The document describes withdrawable injection spears used for injecting chemicals into large diameter water pipes. The spears come in DN8/4, DN20 and DN32 sizes and allow chemicals to be injected into the center of flow while being removable for cleaning. They feature a ball isolation valve and can be withdrawn without stopping water flow. Safety lines are included to prevent the spear fully withdrawing before closing the valve.
The document describes withdrawable injection spears used for injecting chemicals into large diameter water pipes. The spears come in DN8/4, DN20 and DN32 sizes and allow chemicals to be injected into the center of flow while being removable for cleaning. They feature a ball isolation valve and can be withdrawn without stopping water flow. Safety lines are included to prevent the spear fully withdrawing before closing the valve.
The document describes withdrawable injection spears used for injecting chemicals into large diameter water pipes. The spears come in DN8/4, DN20 and DN32 sizes and allow chemicals to be injected into the center of flow while being removable for cleaning. They feature a ball isolation valve and can be withdrawn without stopping water flow. Safety lines are included to prevent the spear fully withdrawing before closing the valve.
Principal of Operation Summary Specification Description Part No.
Designed for installation at the point Withdrawable quills are manufactured DN8/4 Injection Quill 95709571 of chemical injection into a large from grey uPVC components with diameter flow pipe, the ‘quill’ allows EPDM seals. A fully withdrawable the chemical to be dosed into the injection lance to enable Please check chemical chemical solutions to be centre of the main flow, thus compatibility before use. closed into the centre of ensuring good mixing and preventing water flow. Also allows damage from local corrosion or In the DN8/4 quills, Hastelloy C ease of cleaning. Pipe encrustation around the pipeline springs are used in the non-return fittings ½” BSPM. Also boss. valves. fitted with a standard Maximum Operating Pressure: 10 Bar DN8 N/R valve to By means of the ball-type isolating prevent backflow. valve and the seal block/union nut Please Note: The DN8/4 injection Supplied with DN4 & fitted, the ‘quill’ may be withdrawn valves incorporate an “anti- DN8 connections. from the pipeline for siphon/non-return” valve which, in cleaning/maintenance without the itself, provides a backpressure (load) Carbon Dioxide 91339432 necessity of isolating the flow in the of approximately 1 Bar. This load Injection Quill main pipeline. The ‘quill’ passes must be taken into account when As for DN8 injection quill through the ball in the valve, which calculating the overall discharge but has gas diffuser at must be closed when the ‘quill’ has head. end of probe. been withdrawn beyond it and before it is totally removed. DN20 Injection Quill 95714449 Safety Notes A fully withdrawable To prevent accidental total injection lance to enable withdrawal of the ‘quill’ before the chemical solutions to be closed into the centre of valve has been closed, a safety trace water flow. Also allows is fitted to the assembly which should ease of cleaning. Pipe be adjusted on installation so that it fitting 1” BSPM. is at its maximum length when the Chemical Entry - ¾ ‘quill’ has been withdrawn just BSPM and ¾ Hose Barb. beyond the valve ball. When the (does not include valve has been closed, the trace may Non-return valve) then be un-clipped to allow the ‘quill’ to be totally withdrawn. DN32 Injection Quill 95714451 As for DN20 but with Always hold the quill before pipe fitting – 2” BSPM. undoing the union nut to prevent Chemical Entry - 1½” the quill shooting out under BSPM pressure. (does not include Non-return valve)
WESTERN AUSTRALIA SOUTH AUSTRALIA VICTORIA
28 Sorbonne Crescent 29 Deloraine Road Unit 4, 47-51 Little Boundary Road Canning Vale WA 6155 Edwardstown SA 5039 Laverton North VIC 3026 Telephone: (08) 9251 5200 Telephone: (08) 8374 7800 Telephone: (03) 9315 3088 Fax: (08) 9455 4224 Fax: (08) 8374 7899 Fax: (03) 9318 9653 Email: hydramet@hydramet.com.au Email: hydrasa@hydramet.com.auu Email: hydravic@hydramet.com.au PRODUCT DATA SHEET WITHDRAWABLE INJECTION SPEAR SERIES 522
DN8/4 WITHDRAWABLE INJECTION QUILL
Installation Notes 1. It is important that the assembly is properly No. Code Description supported on installation to avoid accidental 1 BFV050 BARREL UNION ½”BSP F breakage, which may occur if left protruding 2 522-0211-02A CHAIN RETAINER from the main pressure pipeline unsupported. 3 522-0211-01A VALVE ADAPTOR 2. For larger diameter pipes, a ‘saddle’ tee 4 (Part of item 10) arrangement is recommended. 5 VEFV050C BALL VALVE ½” (CR seals) 3. The connection provided on the outlet from the 6 522-0211-03A Nylon coated SS trace 275MM ball valve may be bushed to other sizes as 8 50.1336A SCREW SS applicable. (½” BSP for DN8/4, 1” BSP for DN20 9 NFV050 NIPPLE ½” BSP & 2” for DN32) 10 522-021 INJECTION VALVE DN8 4. The standard ‘quill’ length protruding from the 11 529-014 CAP ASSY DN8/4 valve outlet connection can be cut to length to 12 52.104 O RING VITON (SEAL) suit pipe diameter and chamfered to 60° before 13 BS211V O RING VITON (Union) installation. DN20 WITHDRAWABLE INJECTION QUILL (A99 version) Note: Do not shorten DN8 CO2 Quill 1 BFV100 BARREL UNION 1”BSP F 2 522-1521-02A CHAIN RETAINER 11 3 522-1521-01A VALVE ADAPTOR 4 522-1521-05A TUBE ASSY DN20 5 VEFV100C BALL VALVE 1” 10 6 Nylon coated SS trace 440MM 8 10.1336a SCREW SS 2 9 NFV100 NIPPLE 1” BSP 11 AFV050 HOSE TAIL 20MM 1 12 BS118V O RING VITON (Seal) 13 BS219V O RING VITON