Professional Documents
Culture Documents
3 4
Fully A u t o m a t ic Fully A u t o m a t ic
Suitable for both new,old,dirty,tattered polymer bills and paper bills Suitable for both new,old,dirty,tattered polymer bills and paper bills
m oney c ounter m oney c ounter
“CXX”then press“↑”“↓”buttons to choose the desired 8.Error code and solution
Sensitivity level (range from 0-10). After choosing of the level, press
CAUTION: Message Error Solution
1.It is highly recommended to contact the authorized service center The batch display may show some error code when counting,
“RESET”button to confirm.
which means there are some problems with the machine. Problem with the right
or local dealer before you do the above adjustments.
Refer to the following diagram to find way to solve it. E- 1 counting sensor. Clean the sensor or replace it.
<Double Detection function <available for the models with UV
2.Improper adjustments may cause improper working condition or
detection or the model with both UV and MG/MT detection>.
false detection results.
Message Error Solution
Problem with the
---used to check a double-note
Suspicious bill detected by Remove the suspicious bill on the
stacker, press “RESET”to
E-2 preset sensor Clean the sensor or replace it
UV system; continue;
--By default, serving as a supplementary function, the detection can Problem in the UV system. Lower the UV sensitivity.
be activated when the unit is powered up. Problem with the
--If the machine detects a double-note when counting, it will stop and 7.Fake money alarm Suspicious bill detected by
MG/MT system; Problem in
Remove the suspicious bill on the
stacker,press “RESET”to E-3 speed sensor Clean the sensor or replace it
emit beeping sound, while the batch display will show the message continue;
“d3”(alerting the user the of the presence of a double-note). The When fake money pass the machine, the the MG/MT system. Lower the MG/MT sensitivity.
counting will stop and alarm. The function Problem with the
double-note will always be the last one on the stacker. Remove the
dubious bill, press“RESET”button to continue. display will show the error code. The last
3
Double-note detected by
IR system;
Remove the suspicious bill on the
stacker, press “RESET” to E-4 MG head Replace the MG head
note on the stacker normally is the fake Problem in the IR system. continue;
money. The machine counting quantity Lower the IR sensitivity.
<Half-note Detection<available for the models with UV detection or
number is not included in this note. remove Note of size problem Remove the suspicious bill on the < NOTE >
the model with both UV and MG/MT detection>. detected by size detection
the fake money. Press“RESET”button, stacker, press “RESET” to Generally speaking, most of the above-mentioned problems
---used to check half-note. system; Problem in the size continue;
the machine will start counting again. detection system.
may be caused by dust or dirt inside of the machine. So
Lower the size checking sensitivity.
keeping the machine clean is highly recommended .
--By default, serving as a supplementary function, the half-note
Fake money or questionable money Half-note detected by Remove the suspicious bill on the
detection can be activated when the unit is powered up. half-note detection system; stacker,
--If the machine detects a half-note when counting, it will stop and Problem in the half-note press “RESET”to continue.
emit beeping sound, while the batch display will show the message detection system. 9.Hopper adjustment
“d5”alerting the user the presence of a half-note bill). The dubious Slope-note detected by slope-
bill will always be the last one on the stacker. Remove the dubious note detection system; Remove the bill from the stacker. --When improper feeding of bills occur, adjust the feeding thickness
bill, press“RESET”button to continue<the counting display will Problem in the slope-note Press “RESET” to continue.
detection system setting in the hopper by turning the adjustor screw located in the back
clear>. of the machine to ensure proper feeding.
Chain-note detected by chain-
note detection system; Remove the bill from the stacker.
Problem in the chain-note Press “RESET” to continue.
detection system
2.Turning clockwise the adjustor screw to tighten the feeding hopper, shown in figure 2. New roller Old roller
13.Special function
3.Turning counter clockwise the adjustor screw to loosen the feeding hopper, shown in figure 3.
11.Maintenance
1.This model is with 190mm adjustable hopper to secure the counting
4.After adjusting the correct level and counting performance is normal, tighten the protector screw (using a screwdriver), shown in figure 4.
-Do not operate the unit in areas with high temperature or high humidity 2.With chargeable battery (Optional)
When adjusting the bill thickness adjustor screw does not solve the problem of improper bill since it may damage the machine. 3.With low/mid/high 3 counting speed level (Optional)
feeding, you may need further help by.authorized service center. -When not using the unit for a long period of time, remove the power plug
from the wall outlet.
Hand-hold a note. Put it inside the counting roller and resistant rubber. (see the picture). -Never operate the unit under strong light.
To test the tensile force. Clockwise direction is tighten, counter-clockwise direction is loosing. -Clean the machine frequently after switching off and unplugging of the
machine.
-Do not use this product in areas where it may be exposed to water or
other liquids.
-Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaner. Use a brush or a damp cloth for
Tensile force test.
cleaning.
7 8