Professional Documents
Culture Documents
Chassis NC 5AA
Chassis NC 5AA
These instructions are applied to only NC-5AA chassis. 2) Connect H.Scope and Pulse output of Sweamer Generator
to H.Input and Marker input of Alignment Scope,
Notes respectively.
1.So this is a hot chassis, you must be careful, and be caution 3) Apply AGC Voltage(D.C.) to TP11 of IC201.(7.5±0.05V)
not to touch 1st and 2nd concurrently. 4) Apply B+ of IC201 to TP12 of R591.(12.0±0.1V)
2.Adjustment must be done in the correct order. 5) Set VR526(AGC Adjustment) to mechanical center.
3.Power supply of a SET which is adjusted is 100~240V
A.C./50~60Hz. 1.3. Adjustment
4.The receiver must be operated for about 30 minutes proir to A. VCO
the adjustment. 1) Set the vertical range of Alignment Scope to 1V/DIV and
CAL position, and, by applying D.C. 0~9V, do DC
CONTENTS Calibration to place D.C 4.5V point of waveform to center of
1) VIF, AFT and SIF Adjustment Screen.
2) Sound Multiplex Adjustment 2) Connect the Input terminal of Alignment Scope to
3) FOCUS Adjustment TP3(Video Detection Output), and set Vertical Variable
4) AGC Adjustment Switch to CAL position.
4)-1 Picture AGC Adjustment 3) Apply AGC Voltage to TP11 of IC201 through 470§ to be
5) V-Size and V-Center Adjustment 7.5±0.05V
6) Horizontal Size, Center and Side Pincushion Adjustment 4) Adjust L501 so that BEAT appears on 45.75MHz Marker
7) Purity and Convergence Adjustment like <Fig 2> If not, adjust again after attenuating output 10
8) White Balance Adjustment ~20dBu.
9) SUB-Bright Adjustment
10) Vertical Center Adjustment f (MHz)
11) Horizontal Center Adjustment
42.75 45.0 47.25
7.5V L501
VCO COIL 9V
470/0.5W
TP11 2
51
8V
+ 50
C508
TP4
47
R507
8
AFT
R517 L503
Q503 <Figure 3>
44
11 Z502
R518 TP3
2. SIF Adjustment
VCO
14
L502
SWEEMAR
GENERATOR 12.5V
+
2.1. Necessary Instruments
R591
-
POWER
SUPPLY
1) Sweamer Generator : can sweep 3~6MHz
D502
+
TP12 +B 2) Plug In Unit : with 4.5MHz Marker
-ALIGNMENT
3) Alignment Scope : X-Y mode(can measurable 10mV~
SCOPE
20Vp-p)
4) DC Power Supply : 13.5V, over 300mA
<Figure 1> 5) DC Power Supply : 0~12V variable
- 1 -
2.2. Adjustment 100% WHITE
7
1 A/V IN 2 Q202
POWER SUPPLY
C509 VIDEO VIDEO
- + TP8 Q206
3 IC202 6 Q201
7.5V SWEEMAR
A C204 4
5 L201 C201 TP10
GENERATOR
470/0.5W R210
TP11 2
D
SOUND
+
C508
1 8 SOUND
L502 C507
Q603
2
7 Q601 C510
SIF COIL
4 IC501
R609
3
IC601 6
R618
LA7674
TP5
C515
11 45 OSCILLOSCOPE
C516 6.0MHz
14 COLD HOT
Z501
- 2 -
4) Pre-fix 2-pole magnet after adjustment with Lock Ring. 6. White Balance
5) Pull the DY back slowly to get uniformly RED picture and fix 6.1 White Balance Adjustment
it. 6.1.1 Necessary Instrument
1) White BAlance Meter
5.2 Convergence Adjustment
5.2.1 Necessary Instruments 6.1.2 Preliminary Steps
1) Pattern Generator : 216/1 or Equivalents 1) Do this adjustment after operating the SET more than 30
2) Degaussing coil minutes.
2) Receive Standard White pattern.
5.2.2 Preliminary Steps 3) Adjust under “APC ON” condition.
1) Do this adjustment after operating the SET more than 30 4) Turn Screen VR CCW.
minutes. 5) Set Red driver(VR571) and Blue driver(VR572) to
2) Degauss CPT and Cabinet with Degaussing coil. mechanical center.
3) Receive Cross hatch pattern. 6) Set Red Bias(VR574) ,Blue Bias(VR575) and Green
4) Adjust Contrast and Bright properly. Bias(VR573) to 1/3 point to Clock-wise from full CCW.
7) Set SVC SW to “SVC” to get Horizontal line.
5) Untighten half-fixed Magnet Assy lock ring
6.1.3 Adjustment
5.2.3 Adjustment 1) Turn screen VR slowly to see first horizontal line on screen
A. Center(Static) Convergence Adjustment 2) Make horizontal line white with 2 Bias VRs which aren’t
1) Unify Red and Blue vertical lines at center of screen by displayed in 1).
varying the angle of two tabs of 4-pole magnet. 3) Vary screen VR to get very dim horizontal line.
2) Rotate tab with sustaining the angle of item 1) and unify 4) Set SVC SW to “Normal” position.
Red and Blue vertical lines at center of screen. 5) Receive adjustment signal-White in upper and Black in
3) Unify Red,Blue and Green vertical lines by adjusting two Lower.
tab2 of 6-pole magnet. 6) Vary Red driver(VR571) and Blue driver(VR572) to get
4) Rotate tab with sustaining the angle of item 3) and unify White screen in White.
Red,Blue and Green vertical lines. 7) Vary Bias and Drivers to get the best screen in White and
5) To get more detail adjustment repeat 1),2) with Black.
remembering changes of Red,Blue and Green. 8) Check adjustment condition with White Balance Meter.
6) Fix magnet assy lock ring. 9) Refer below for Adjustment
B. Dynamic Convergence Adjustment
1) Prepare bonded rubber wedge. Color Temperature X Y
2) Adhere rubber wedge to “A” part halfly.
(Don’t remove paper of bonding part.) 10,000K 0.281 0.288
3) Move the DY every direction to get best convergence in High Light : 40fl
every corner. Low Right : 4fl
4) Adhere rubber wedge to bottom of CPT.(Refer <Fig 9>).
5) After checking the locatons of 3 wedges and check 7. Focus Adjustment
Convergence. 1) Receive Digital pattern.
6) Paint white lacquer on DY fixing nut and magnet. 2) Set screen conditon to “APC ON”.
DEFLECTION YOKE 3) Turn Focus VR to get the best condition in center and
ADHESIVE TAPE PURITY &CONVERGENCE every corner.
MAGNET ASSEMBLY
6-POLE
8. Sub-Bright Adjustment
1) Receive Digital pattern.
,
,,,,,,,,,, 2) Do this adjustment after operating the SET more than 30
,,,,,, ,,,,,,,,,,,,,
,,,,,,,,,, ,,,,,,,,
,
,,,,,,,,,, ,,,,,,, minutes.
,,,,,, ,,,,
- 3 -
HOT COLD
AUDIO IN VIDEO IN
IC601
Q603 JA001
3
T403
IC501
PRE-AMP. Z101 VIF IC202
8 SIF-IN
48
TU100 LA7674 SFE4.5 40 Q208
Q102 SIF 9
TUNER AFT
DET-OUT
50 44
VCO IC602
SHARP 51 34
5V 12V 33V BRI TPS4.5
LOCK
COLOR 45 6 1 TDA 4 SP
CLOCK AFT -Y 2006
DATA TINT 46 21
IC1 CONT
CS
BLOCK DIAGRM
H V
13
TX PA1 23 28
TMP67CC31
PRE-AMP 35 CPT PCB
IC2 CPT
- 1 -
Q11 Q10
5V Q402
RL801 Q401 H. D. T
1877
12V
D/G
Q806
COIL T402
FBT
IC801 1 5 TO IC1 HT 9
TO CPT 24V 5
3 TO T403
STR50092K 8 24V 6
12V
2
FBP 10
5