Professional Documents
Culture Documents
Ip Tahun 3 Sem II Sesi 20202021 - Its
Ip Tahun 3 Sem II Sesi 20202021 - Its
COURSE LECTURERS:
Based on the product assigned for your group, prepare a report according to the given tasks in Table 1:
3 KKKR3733 Below are the required tasks for Separation Process II subject:
a) Select a separation unit or units to treat a stream and determine the process
design in terms of temperature, pressure, flow rates, compositions and heat
duty and/or other related parameters.
b) Perform the mass balance on the unit and compare your results with
SuperPro®/ Aspen HYSYS/ Aspen Plus/ Symmetry simulation.
2
4 KKKR3723 Below are the required tasks for Utility and Pressure Vessel Design subject:
a) Determine and explain the need of each utility and mechanism involved in the
equipment.
b) Design and estimate each utility unit in the plant using Kern Method focusing
on the thermal and hydraulic analysis.
c) Design two pressure vessels under respective internal and external pressures
according to ASME Code procedure by considering the corrosion allowance
and nominal in order to determine the wall thickness and the MAWP of the
pressure vessel.
d) Consider also the combined loading of the pressure vessel and perform the
detailed design for the vessel support and flanges, and produce a detailed
engineering drawing on the selected pressure vessels.
5 KKKR3713 Below are the required tasks for Dynamic and Process Control subject:
a) Each student in all group must select ONE unit operation used in their process
and based on the chosen unit operation:
i) Explain the type of control configuration that can be applied to the unit
operation and state the reason of choosing the configuration.
ii) Develop the mathematical modelling of the unit operation to calculate
the Degree of Freedom (DOF) and state your assumptions (if any).
iii) Draw the Piping & Instrumentation Diagram (P&ID) for the unit
operation.
iv) In a Table form, summarize all the type of controllers, control
objectives, control variables, manipulated variables, control actions and
type of valve used in the control configuration. State the set points and
stream numbers accordingly.
b) Conduct a plantwide process control on your whole process and draw the
P&ID. Enclosed the diagram with your final report with proper formatting.
3
Final Report:
The final report must be presented according to the Panduan Penulisan Tesis Gaya UKM, Cetakan Ketiga (2015)
format, inclusive of citation in text formatting and list of references. The report should include all the following:
4
Table 2 List of Groups and Project titles (Set 1 Integrated Project Semester II Academic Session 2020/2021)
5
Table 3 List of Groups and Project titles (Set 2 Integrated Project Semester II Academic Session 2020/2021)
6
Figure 1 Evaluation and Assessment of Integrated Project (20-25 %)
7
Table 4 Integrated Project Planner for Semester II (2020/2021)
MINGGU/TARIKH MULA 1 2 3 4 5 6 7 CPS 8 9 10 11 12 13 14 15 16 17 18
22/ 29/ 5/ 12/ 19/ 26/ 3/ 10/ 17/ 24/ 31/ 7/6 14/ 21/ 28/ 5/ 12/7-30/7
AKTIVITI 3 3 4 4 4 4 5 5 5 5 5 6 6 6 7 (exam)
PROJEK BERSEPADU
THN III - KKKR3733, KKKR3723, KKKR3713, KKKR3743 (Penyelaras: Dr Jarinah)
Taklimat PB Tahun III, Khamis
25/3/2021
Perjumpaan pelajar-pensyarah (buku log) 29/3 – 4/6/2021
Penghantaran cadangan tajuk dan Jumaat 2/4/2021
kumpulan bagi Thn III
Penghantaran Draf Awal I (Introduction, Khamis 8/4/2021
Usage, Process Description, PFD)
Examiners:
PM Noorhisham (Set 1) &
Dr. Ahmad Razi (Set 2)
Penghantaran Draf Awal II (Economic Khamis 22/4/2021
Issues)
Examiners:
PM Ir. Dr. Hassimi/ Dr. Zulhaziman
(Set 1) &
Dr. Darman (Set 2)
Penghantaran Draf Awal III Khamis 6/5/2021
(Environmental and Safety Issues)
Examiners:
PM Dr. Norliza (Set 1) &
Dr. Jarinah (Set 2)
Penghantaran Draf Awal IV (Material Khamis 27/5/2021
and Energy Balances)
Examiner:
PM Ir. Dr. Shuhaida (Set 1) &
Ir. Dr. Teow (Set 2)
Penghantaran Laporan Akhir PB Khamis 17/6/2021
Pembentangan PB Thn III @ 8am-5pm,
Rabu 23/6/2021