Professional Documents
Culture Documents
10137-2:1996
Contents
Page
Committees responsible Inside front cover
National foreword ii
Foreword 2
Text of EN 10137-2 3
List of references Inside back cover
© BSI 11-1998 i
BS EN 10137-2:1996
National foreword
This British Standard has been prepared by Technical Committee ISE/12 and is
the English language version of EN 10137-2:1995 Plates and wide flats made of
high yield strength structural steels in the quenched and tempered or precipitation
hardened conditions — Part 2: Delivery conditions for quenched and tempered
steels, published by the European Committee for Standardization (CEN).
Together with BS EN 10137-1:1996 and BS EN 10137-3:1996, it supersedes
BS 7163:1994 which is withdrawn.
Cross-references
Publication referred to Corresponding British Standard
EN 10137-1:1995 BS EN 10137 Plates and wide flats made of high yield
strength structural steels in the quenched and tempered
or precipitation hardened conditions
Part 1:1996 General delivery requirements
A British Standard does not purport to include all the necessary provisions of a
contract. Users of British Standards are responsible for their correct application.
Compliance with a British Standard does not of itself confer immunity
from legal obligations.
Summary of pages
This document comprises a front cover, an inside front cover, pages i and ii,
the EN title page, pages 2 to 10, an inside back cover and a back cover.
This standard has been updated (see copyright date) and may have had
amendments incorporated. This will be indicated in the amendment table on
the inside front cover.
ii © BSI 11-1998
EUROPEAN STANDARD EN 10137-2
NORME EUROPÉENNE
EUROPÄISCHE NORM September 1995
Descriptors: Iron and steel products, metal plates, wide flats, steels, structural steels, high yield strength steels, delivery conditions,
quenching (cooling), tempering, chemical composition, grades, quality, classifications, designation, mechanical
characteristics, inspection, tests, marking
English version
Plates and wide flats made of high yield strength structural
steels in the quenched and tempered or precipitation
hardened conditions —
Part 2: Delivery conditions for quenched and tempered
steels
Tôles et larges plats en aciers de construction à Blech und Breitflachstahl aus Baustählen mit
haute limite d’élasticité à l’état trempé et höherer Streckgrenze im vergüteten oder im
revenu ou durci par précipitation — ausscheidungsgehärteten Zustand —
Partie 2: Conditions de livraison des aciers à Teil 2: Lieferbedingungen für vergütete Stähle
l’état trempé et revenu
CEN
European Committee for Standardization
Comité Européen de Normalisation
Europäisches Komitee für Normung
Central Secretariat: rue de Stassart 36, B-1050 Brussels
© 1995 All rights of reproduction and communication in any form and by any means reserved in all
countries to CEN and its members.
Ref. No. EN 10137-2:1995 E
EN 10137-2:1995
Foreword Page
8.6 Test methods 6
This European Standard has been prepared by the 8.7 Retests and resubmission for testing 6
Technical Committee ECISS/TC 10, Structural
steel — Qualities, the secretariat of which is held by 8.8 Inspection documents 6
NNI. 9 Marking 6
This European Standard shall be given the status of 10 Disputes 7
a national standard, either by publication of an 11 Options 7
identical text or by endorsement, at the latest by
March 1996, and conflicting national standards Annex A (informative) List of corresponding
shall be withdrawn at the latest by March 1996. former designations 8
According to the CEN/CENELEC Internal Annex B (Informative) Minimum inside
Regulations, the following countries are bound to bend radii for flanging 9
implement this European Standard: Austria, Table 1 — Chemical composition of the ladle
Belgium, Denmark, Finland, France, Germany, analysis for quenched and tempered steels 4
Greece, Iceland, Ireland, Italy, Luxembourg, Table 2 — Mechanical properties for
Netherlands, Norway, Portugal, Spain, Sweden, quenched and tempered steels 5
Switzerland, United Kingdom. Table 3 — Minimum values of impact
energy for impact tests on longitudinal
Contents v-notch test pieces 6
Page Table 4 — Minimum values of impact
Foreword 2 energy for impact tests on transverse
v-notch test pieces, when the impact test
1 Scope 3 on transverse test pieces is agreed at the
2 Normative references 3 time of the enquiry and order.
3 Definitions 3 See clause 11 , option 4 7
4 Information to be supplied by Table A.1 — List of corresponding
the purchaser 3 former designations 8
4.1 General 3 Table B.1 — Minimum inside bend
radii for flanging 9
4.2 Options 3
5 Dimensions, mass and tolerances 3
5.1 Dimensions and tolerances 3
5.2 Mass of steel 3
6 Classification and designation 3
6.1 Classification 3
6.2 Designation 3
7 Technical requirements 3
7.1 Steel manufacturing process 3
7.2 Delivery condition 3
7.3 Chemical composition 3
7.4 Mechanical properties 3
7.5 Technological properties 5
7.6 Surface finish 6
7.7 Internal soundness 6
8 Inspection and testing 6
8.1 General 6
8.2 Sampling 6
8.3 Test units 6
8.4 Verfication of chemical composition 6
8.5 Preparation of samples and test pieces 6
2 © BSI 11-1998
EN 10137-2:1995
© BSI 11-1998 3
4
Table 1 — Chemical composition of the ladle analysis for quenched and tempered steelsa
Grade Quality C Mn Si P S N B Cr Cu Mo Nb Ni Ti V Zr
% % % % % % % % % % % % % % %
max. max. max. max. max. max. max. max. max. max. max. b max. max. b max. b max. b
All grades (no symbol) 0,20 1,70 0,80 0,025 0,015 0,015 0,0050 1,50 0,50 0,70 0,06 2,0 0,05 0,12 0,15
L 0,020 0,010
L1 0,020 0,010
EN 10137-2:1995
a Depending on the thickness of the product and the manufacturing conditions, the manufacturer may add to the steel one or several alloying elements up to the maximum values
given in order to obtain the specified properties (see 7.3.2 ).
b There shall be at least 0,015 % of a grain-refining element present. Aluminium is also one of these elements. The minimum content of 0,015 % applies to soluble aluminium, this
value is regarded as attained if the total aluminium content is at least 0,018 %; in case of dispute the soluble aluminium content shall be determined.
© BSI 11-1998
EN 10137-2:1995
If agreed at the time of the enquiry and order the If specified at the time of the enquiry and order
requirements of EN 10137-1 shall apply. plates and wide flats ordered and supplied in the
quenched and tempered condition with a nominal
See clause 11 , option 5. thickness ≤ 16 mm are suitable for flanging without
7.5 Technological properties cracking with the indicative values for the inside
7.5.1 Weldability bend radii for cold forming as given in annex B.
See clause 11 , option 6.
Weldability shall be in accordance with EN 10137-1.
7.5.2 Formability 7.5.3 Other requirements
NOTE Recommendations regarding hot and cold forming are
If specified at the time of enquiry and order the
laid down in ECSC IC 2. grade S460 shall be suitable for hot-dip zinc-coating
and shall comply with the relevant product quality
requirements.
See clause 11 , option 7.
Table 2 — Mechanical properties for quenched and tempered steels
Designation of steel Minimum yield strength ReH Tensile strength Rm Minimum percentage
grade elongation at fracture
N/mm 2 N/mm 2 %
Nominal thickness Nominal thickness
mm mm
Name Material ≥3 > 50 > 100 ≥3 > 50 > 100 Lo = 5,65 So
© BSI 11-1998 5
EN 10137-2:1995
6 © BSI 11-1998
EN 10137-2:1995
10 Disputes 11 Options
In case of disputes EN 10137-1 applies. See options 1 to 13 of EN 10137-1.
7.6 ).
14) Repair by welding is allowed (see
Table 4 — Minimum values of impact energy for impact tests on transverse v-notch test pieces,
when the impact test on transverse test pieces is agreed at the time of the enquiry and order.
See clause 11, option 4
Designation of steel grade Minimum values of impact energy in J at test temperatures, in °C
Name Material number 0 – 20 – 40 – 60
S460Q 1,8908
S500Q 1,8924
S550Q 1,8904
S620Q 1,8914 30 27 — —
S690Q 1,8931
S890Q 1,8940
S960Q 1,8941
S460QL 1,8906
S500QL 1,8909
S550QL 1,8926
S620QL 1,8927 35 30 27 —
S690QL 1,8928
S890QL 1,8983
S960QL 1,8933
S460QL1 1,8916
S500QL1 1,8984
S550QL1 1,8986
S620QL1 1,8987 40 35 30 27
S690QL1 1,8988
S890QL1 1,8925
© BSI 11-1998 7
EN 10137-2:1995
Annex A (informative)
List of corresponding former designations
Table A.1 — List of corresponding former designations
Designation of steel grade Equivalent former designations in
Name Material number EU 137 (1983) Germany France Sweden
S460Q 1,8908 FeE 460 V
S460QL 1,8906 FeE 460 V KT TStE 460 V S 460 T
S460QL1 1,8916
S890Q 1,8940
S890QL 1,8983 TStE 890 V
S890QL1 1,8925 EStE 890 V
S960Q 1,8941
S960QL 1,8933 TStE 960 V S 960 T
8 © BSI 11-1998
EN 10137-2:1995
Annex B (informative)
Minimum inside bend radii for flanging
Table B.1 — Minimum inside bend radii for flanging
Designation of steel grade Minimum recommended inside bend radii for
nominal thicknesses (t) 3 ≤ t ≤ 16 mma
Name Material number Axis of bend in transverse Axis of bend in longitudinal
direction direction
S460Q 1,8908 3,0t 4,0 t
S460QL 1,8906 3,0t 4,0 t
S460QL1 1,8916 3,0t 4,0 t
© BSI 11-1998 9
10 blank
BS EN 10137-2:1996
List of references
See national foreword.
© BSI 11-1998
||
||
||
||
||
BSI Ð British Standards Institution
||
||
||
|| BSI is the independent national body responsible for preparing British Standards. It
presents the UK view on standards in Europe and at the international level. It is
|| incorporated by Royal Charter.
||
|| Revisions
|| British Standards are updated by amendment or revision. Users of British Standards
|| should make sure that they possess the latest amendments or editions.
||
|| It is the constant aim of BSI to improve the quality of our products and services. We
would be grateful if anyone finding an inaccuracy or ambiguity while using this
|| British Standard would inform the Secretary of the technical committee responsible,
|| the identity of which can be found on the inside front cover. Tel: 020 8996 9000.
|| Fax: 020 8996 7400.
||
|| BSI offers members an individual updating service called PLUS which ensures that
|| subscribers automatically receive the latest editions of standards.
|| Buying standards
|| Orders for all BSI, international and foreign standards publications should be
|| addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001.
||
|| In response to orders for international standards, it is BSI policy to supply the BSI
|| implementation of those that have been published as British Standards, unless
|| otherwise requested.
|| Information on standards
|| BSI provides a wide range of information on national, European and international
|| standards through its Library and its Technical Help to Exporters Service. Various
|| BSI electronic information services are also available which give details on all its
|| products and services. Contact the Information Centre. Tel: 020 8996 7111.
|| Fax: 020 8996 7048.
|| Subscribing members of BSI are kept up to date with standards developments and
|| receive substantial discounts on the purchase price of standards. For details of
|| these and other benefits contact Membership Administration. Tel: 020 8996 7002.
|| Fax: 020 8996 7001.
||
|| Copyright
|| Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of
|| the publications of the international standardization bodies. Except as permitted
|| under the Copyright, Designs and Patents Act 1988 no extract may be reproduced,
|| stored in a retrieval system or transmitted in any form or by any means ± electronic,
|| photocopying, recording or otherwise ± without prior written permission from BSI.
|| This does not preclude the free use, in the course of implementing the standard, of
|| necessary details such as symbols, and size, type or grade designations. If these
|| details are to be used for any other purpose than implementation then the prior
|| written permission of BSI must be obtained.
|| If permission is granted, the terms may include royalty payments or a licensing
|| agreement. Details and advice can be obtained from the Copyright Manager.
|| Tel: 020 8996 7070.
||
||
||
||
BSI ||
389 Chiswick High Road ||
London ||
W4 4AL ||
||
||
|