Professional Documents
Culture Documents
Sanitary, Plumbing Works and Cleaning, Repainting and Sterlization of Watertank
Sanitary, Plumbing Works and Cleaning, Repainting and Sterlization of Watertank
CONTENTS
(C) BRC 2
SCHEDULE OF RATES
PREAMBLE
1. The rates contained herein include the use of materials, labour, maintenance, supply
of fuel and all idling time of vehicles, opening up, taking down, cutting and refixing,
preparation for washing, turning on and off of water supply, tightening bolts and nuts
(where necessary), provision of standby plumbers, ladders and torchlights, other
tools / equipment and removal of all debris, empty tins and other unwanted materials
from the roofs, all as specified, including making good all leaking tank panels with
approved sealants (where necessary), conveyance, delivery, unloading, storing,
hoisting, stools/ladders, all labour setting, fitting, fixing in position, all cutting and
waste, return of packings, establishment charges, overheads, profit and all forms of
claim for loss and expense and making good all work disturbed, unless otherwise
stated.
2. The rates of painting of water tanks unless otherwise stated include the preparation
of surfaces as per manufacturer’s recommendations and Employer’s instructions.
No dilution of coating materials are allowed unless recommended by the
manufacturer and the Employer. The application of coating materials shall comply
strictly to the manufacturer’s recommendations and Employer’s instructions.
3. The cost of hacking, removal and disposal, and the making good of all affected
works shall be deemed to be included in the Schedule of Rates unless otherwise
stated. All schedule of Rates shall be applicable for new and replacement work.
4. Unless otherwise stated, all works shall be measured nett as fixed in its place.
Length of pipes shall be measured based on exposed length.
5. All pipes are described by their respective nominal size specified by the respective
manufacturers.
6. The Employer reserves the right to direct the Contractor to execute any of the
undermentioned items of works which he considers necessary.
7. No scaffold (other than a tower scaffold and trestle scaffold) exceeding 4 metres
shall be erected, installed, re-positioned, altered or dismantled except by an
approved Scaffold Contractor. An approved Scaffold Contractor shall engage a
qualified Scaffolding Supervisor to ensure that the scaffold is erected, installed, re-
positioned, altered or dismantled in accordance with the Regulations. The 4
metres height is defined as the distance between the ground level where scaffold
rests and the level of the highest working platform. The Schedule of Rates have
taken into consideration of the scaffolding cost for height not exceeding 4 metres.
The Contractor shall be paid separately for the scaffolding if its height exceeds 4
metres.
8. All brass fittings, valves, cocks & taps shall be of Dezincification Resistant type
unless otherwise stated.
10. Denotations
B 014 Extra over item B012 for concrete grade 20 base of m 13.10 SB 14
150mm thick
B 015 Extra over item B013 for concrete grade 20 base of m 18.90 SB 15
150mm thick
(C) BRC
C 001 A6 m2 6.40 SC 1
C 002 A7 m2 8.25 SC 2
C 003 A8 m2 10.80 SC 3
C 004 B6 m2 10.70 SC 4
C 005 B7 m2 12.30 SC 5
C 006 B8 m2 16.20 SC 6
C 007 C6 m2 5.00 SC 7
C 008 C7 m2 6.10 SC 8
C 009 C8 m2 7.40 SC 9
Fixed Scaffold
Mobile Scaffold
D 005 Add for item 004 for labour in dismantling, No. 57.50 SD 5
shifting to new location and re-erection
(E) MANHOLE
Manhole Construction
E 006 225mm thick brick works in cement mortar (1:3) for m2 68.90 SE 6
walls of manhole with 20mm thick cement plaster
internally
Manhole Cover
E 011 Cast iron light duty manhole cover and frame Set 71.30 SE 11
with retractable lifting handle including setting
frame in cement mortar (1:3) and sealing cover in
grease and fine sand
E 012 Cast iron light duty manhole cover with retractable No. 65.30 SE 12
lifting handle (excluding frame) and sealing cover in
grease and fine sand
E 013 Cast iron light duty manhole frame only No. 35.80 SE 13
E 014 Lifting handle for cast iron light duty manhole No. 5.70 SE 14
cover
E 015 Cut 2mm wide x 50mm long (maximun) slit at both Job 3.20 SE 15
handle area of existing cast iron manhole cover
E 017 Hydrostatic test of manhole not exceeding 1.5m deep No. 380.00 SE 17
by Licensed Plumber including liaison and submission
of report / result to PUB
G 003 100mm diameter pipe for "duck" foot bend No. 45.00 SG 3
G 004 150mm diameter pipe for "duck" foot bend No. 77.00 SG 4
G 022 Steel bolt for cast iron inspection covers No. 0.70 SG 22
G 027 Cast iron heavy duty 100mm diameter "duck" foot No. 72.10 SG 27
bend including breaking up concrete floor
G 028 100mm diameter cast iron heavy duty union No. 24.50 SG 28
socket for underground pipe
G 029 Cast iron downspout outlet fixed to 75mm diameter No. 14.50 SG 29
cast iron pipe with three numbers of tightening bolts
G 030 225mm x 450mm cast iron purpose made street No. 149.80 SG 30
gully with 100mm outlet including connection, all
necessary excavation and concrete surround.
G 031 110mm diameter cast iron coupling joint including No. 174.10 SG 31
all necessary bolts & nuts
H 006 Extra over item H001, H004 & H005 for bolted flange Joint 9.20 SH 6
joints including all necessary drilling, bolt nut and
gasket
H 011 Extra over items H002, H009 & H010 for bolted Joint 19.60 SH 11
flange joints including all necessary drilling, bolts
and gaskets
H 021 215mm diameter flange washer for water mains No. 5.30 SH 21
H 026 Extra over Item H003, H024 & H025 for bolted Joint 24.30 SH 26
flange joints including all necessary drilling bolts
and gaskets
H 027 Cement lining for 100mm diameter ductile iron fitting No. 8.10 SH 27
H 028 Cement lining for 150mm diameter ductile iron fitting No. 9.40 SH 28
H 029 100mm x 50mm ductile iron cement lined flange tee No. 54.00 SH 29
H 039 Extra over ductile iron pipe for 80mm elbow (all m 21.50 SH 39
angles)
H 040 Extra over ductile iron pipe for 100mm diameter m 25.20 SH 40
elbow (all angles)
H 041 Extra over ductile iron pipe for 150mm diameter m 48.10 SH 41
elbow (all angles)
H 042 13mm diameter stainless steel bolt, nut and No. 2.20 SD 42
washer for flange joint or other fitting
H 043 Ductile iron flange adaptor for 100mm diameter No. 2.20 SD 43
pipe
H 046 Cable tie for securing half channel UPVC pipe No. 0.30 SH 46
cover to main water distribution main
Soil/Waste Pipe
J 054 120mm x 275mm upvc rectangular elbow (SS 272) No. 157.20 SJ 54
plain (Inspection opening including access
cap measured separately)
J 069 Extra over UPVC fitting (various sizes) that comes No. 1.70 SJ 69
with inspection opening (cleaning eye) including
access cap
J 070 Form new opening (cleaning eye) on existing UPVC No. 7.80 SJ 70
pipe fitting complete with boss connector and access
cap
J 071 Screw-on cover for access opening in UPVC testing No. 4.80 SJ 71
opening fitting
J 079 100mm diameter UPVC vent cowl to vent pipe No. 2.60 SJ 79
J 080 150mm diameter upvc vent cowl to vent pipe No. 5.80 SJ 80
J 084 Above 80mm diameter but not exceeding 150mm No. 4.20 SJ 84
diameter
J 086 48mm diameter spigot adaptor for 50mm diameter No. 10.80 SJ 86
cast iron pipe
J 087 72mm diameter spigot adaptor for 80mm diameter No. 14.40 SJ 87
cast iron pipe
J 088 65mm diameter spigot adaptor for 80mm diameter No. 14.40 SJ 88
cast iron vent pipe
J 089 95mm or 96mm diameter spigot adaptor for 100mm No. 19.20 SJ 89
diameter cast iron pipe
J 090 96mm diameter spigot adaptor for 100mm diameter No. 29.50 SJ 90
cast iron 'S' bend
J 092 95mm diameter pan collar adaptor for 100mm No. 28.20 SJ 92
diameter cast iron pipe
J 093 148mm diameter spigot adaptor for 150mm diameter No. 21.60 SJ 93
cast iron pipe
J 094 95mm diameter grating adaptor for 100mm diameter No. 33.30 SJ 94
cast-iron pipe with one/two side inlets irrespective
of size
J 095 117mm diameter grating adaptor for 125mm diameter No. 34.50 SJ 95
cast-iron pipe with one/two side inlets irrespective
of size
J 096 50mm diameter w.c. straight connector with spigot No. 16.80 SJ 96
not exceeding 100mm long
J 097 80mm diameter w.c. straight connector with spigot No. 18.10 SJ 97
not exceeding 100mm long
J 098 100mm diameter w.c. straight connector with spigot No. 19.40 SJ 98
not exceeding 100mm long
J 099 100mm diameter w.c. straight connector with spigot No. 24.40 SJ 99
exceeding 100mm but not exceeding 150mm long
J 100 125mm diameter w.c. straight connector with spigot No. 25.40 SJ 100
not exceeding 100mm long
J 101 125mm diameter w.c. straight connector with spigot No. 26.90 SJ 101
exceeding 100mm but not exceeding 150mm long
J 102 150mm diameter w.c. straight connector with spigot No. 27.50 SJ 102
not exceeding 100mm long
Copper Pipe
Brass Elbow
Brass Coupling
Brass Tee
Brass Nipple
Coupling Ring
Hanger
L 001 Purpose made 32mm wide x 4mm thick mild No. 15.40 SL 1
steel hanger for pipe not exceeding 100mm
diameter including anchoring to structure using
approved expansion bolt
L 002 Purpose made 32mm wide x 4mm thick mild No. 18.60 SL 2
steel hanger for pipe exceeding 100mm diamter
but not exceeding 200mm diameter including
anchoring to structure using approved
explosion bolt
L 003 15mm to 20mm wide punched steel pipe hanger No. 5.20 SL 3
including anchoring to structure using approved
expansion bolt (Band not exceeding 1.5 metre long)
L 010 Galvanised steel holderbats or clips for water pipes No. 1.50 SL 10
not exceeding 25mm diameter
L 011 Galvanised steel holderbats or clips for water pipes No. 2.40 SL 11
exceeding 28mm but not exceeding 54mm diameter
L 020 More than 40mm diameter but not exceeding No. 79.20 SL 20
50mm diameter
L 021 More than 50mm diameter but not exceeding No. 145.20 SL 21
80mm diameter
L 022 More than 80mm diamter but not exceeding No. 171.60 SL 22
100mm diameter
L 023 More than 100mm diameter but not exceeding No. 202.40 SL 23
150mm diameter
Fireclay Sink
M 008 500mm x 400mm (white) with delay action pillar No. 151.10 SM 8
tap in lieu of push button spring type
M 009 500mm x 400mm (coloured) with delay action pillar No. 160.70 SM 9
tap in lieu of push button spring type
M 011 Integral coloured cultured marble basin and top of No. 544.40 SM 11
approximate size 525 x 1500mm with backsplash,
200mm front apron complete with integrated basin,
approved single lever mixer tap with pop-up waste,
bottle trap, waste pipe and galvanised steel bracket
for fixing to wall, and all necessary accessories for
fixing and jointing to pipework miniature stop valve
with flexible tube
M 012 550mm x 450mm stainless steel wash hand basin No. 63.10 SM 12
complete with pillar tap, cantilever brackets,
vulcanite plug and chain, all necessary trap, waste
pipe miniature stop valve and flexible tube
Sink
M 013 1000mm x 500mm single bowl single drainer 2.03mm No. 66.00 SM 13
thick anodised aluminium sink complete with
cantilever brackets 40mm vulcanite plug and chain,
all necessary trap, waste pipe miniature stop valve
and flexible tube
M 016 1500mm x 500mm locally made single bowl double No. 200.90 SM 16
drainer stainless steel sink complete with
cantilever brackets 40mm vulcanite plug and chain,
all necessary trap, waste pipe miniature stop valve
and flexible tube
M 017 1500mm x 500mm locally made double bowl single No. 223.20 SM 17
drainer stainless steel sink complete with cantilever
brackets 40mm vulcanite plug and chain, all
necessary trap, waste pipe miniature stop valve
and flexible tube
M 022 White earthenware squat w.c. pan only, complete No. 146.30 SM 22
with trap and with/without vent including making good
tile surround to match if necessary and hacked up
existing damage pan
M 023 White earthenware pedestal w.c. pan only, complete No. 231.00 SM 23
with plastic seat and trap with or without vent
M 025 White vitreous China wall hung urinal bowl No. 114.80 SM 25
M 026 White glazed urinal slabs 600mm wide x 1050mm No. 551.30 SM 26
high
M 027 White glazed urinal return end slab 1050mm high to No. 245.00 SM 27
match existing
Cistern
M 031 9/4.5 litres dual action approved high level plastic No. 45.50 SM 31
cistern complete with nylon cord, plastic pull and
brackets
M 032 9/4.5 litres dual action approved low level plastic No. 45.50 SM 32
cistern complete with flush bend, actuating lever
handle and cantilever brackets
M 033 UPVC pipe, for sink waste including elbow and bend No. 11.00 SM 33
M 034 Vulcanite plug complete with chain for sink or basin No. 3.30 SM 34
M 035 5mm diameter x 75mm long brass grid screw to No. 1.20 SM 35
sink.
M 036 Brass waste fitting to sink or basin complete with Set 6.90 SM 36
brass cobweb grating, chain and plug
M 037 Brass waste fitting to sink or basin complete with No. 4.80 SM 37
brass cobweb grating only.
M 039 15mm Sink mixer lift-up tap with swivel spout No. 57.50 SM 39
M 040 `Presto' No. 605 or other approved wash basin delay No. 89.70 SM 40
action pillar tap.
M 041 Cast iron brackets for draining board, sink, basin or No. 6.20 SM 41
cistern including cutting and fixing to walls
M 042 PVC screw cap for vent of w.c. squat/pedestal pan No. 2.80 SM 42
M 043 Plastic w.c. seat complete with cover. (Heavy duty No. 26.40 SM 43
of any colour)
M 044 Plastic w.c. seat but without cover. (Heavy duty No. 9.90 SM 44
of any colour)
M 045 Rubber cone for joint between flush pipe and back No. 3.30 SM 45
inlet of w.c. pedestal pan.
M 047 Porcelain enamelled foot treads for squat pan Pair 33.60 SM 47
including hacking up existing and make good tile
surround if necessary to match existing
Sparge Pipe
M 054 Glazed vitreous clay lid cover to w.c. cistern No. 10.20 SM 54
M 057 Brass chain and rubber pull for high level cistern No. 6.90 SM 57
M 059 Brass nut for flush pipe to w.c. cistern outlet No. 5.40 SM 59
connection .
M 060 Chromium plated lever handle to low level w.c. No. 5.30 SM 60
cistern.
M 065 Plastic flush arm holder with nylon rope to w.c. No. 3.10 SM 65
cistern.
M 067 Plastic nut for flush pipe to w.c. cistern outlet No. 4.20 SM 67
connection
M 068 PVC flush pipe not exceeding 2.0m long bend to No. 5.30 SM 68
high level cistern
M 069 PVC flush pipe exceeding 2.0m but not exceeding No. 6.30 SM 69
3.0m long bent to high level cistern
M 070 40mm PVC flush pipe to low level cistern No. 4.20 SM 70
M 075 Galvanised steel cistern chain and pull for No. 6.20 SM 75
high level cistern
M 077 More than 300mm long but not exceeding No. 4.50 SM 77
600mm long
M 080 Surfaced mounted chromium plated toilet roll holder No. 12.50 SM 80
with plastic roller fixed or plugged to wall
M 081 Surfaced mounted plastic type toilet roll holder with No. 8.90 SM 81
plastic roller fixed or plugged to wall
M 082 Approved plastic roller fixed in existing toilet roll No. 0.70 SM 82
holder brackets
Soap Tray/Dispenser
M 083 150 x 150mm white glazed recessed type soap tray No. 14.90 SM 83
embedded in cement mortar including hacking off
existing and make good tile surround to match
M 084 108mm x 108mm white glazed recessed type soap No. 16.90 SM 84
tray embedded in cement mortar
M 085 20G 18-8 Type 304 stainless steel rectangular liquid No. 43.80 SM 85
soap dispenser or other approve of 1.2 litre capacity
equipped with acrylic soap level window, exposed
surface stain-finished complete with vandal resistant
mounting bracket and separate concealed wallplate
M 086 Horizontal all purposed valve (Model CV-025A) for No. 9.90 SM 86
stainless steel liquid soap dispenser constructed of
chrome plated brass with Buna-N "O" ring markings
with engineering plastic moving parts and push-in
type valve projecting 61mm
M 088 Deck mounted stainless steel liquid soap dispenser No. 47.80 SM 88
Mirror
Shower Rose
M 093 Standard ABS chrome plated shower set comprising Set 115.00 SM 93
shower head (minimum 2 spray patterns),
wall mounted sliding rail, height adjustable and
rotatable shower head holder and soap dish and
minimum 1.5m long flexible connecting tube
M 094 Long bath trap complete with waste fittings and No. 11.40 SM 94
overflow pipes
M 097 Temporary removal of long bath tub to facilitate repair No. 91.30 SM 97
works and re-install the existing long bath tub upon
completion of repair works including all necessary
reinstatement of wall tiles, pipings and fittings
(reinstatement of wall tiles and pipe fittings measured
separately)
Hand Dryer
M 100 25mm diameter C.P. copper flush pipes including all No. 13.70 SM 100
necessary tees and brackets for each chute
M 101 25mm diameter galvanised steel flush pipe including No. 11.00 SM 101
all necessary tees and brackets for each chute
Stop Cock
Bib Tap
N 011 13mm brass bib tap with spigot nozzle including No. 10.50 SN 11
detachable tap head
N 012 13mm brass bib tap with a hole drilled through No. 11.00 SN 12
the shaft for the tap head for locking purpose
N 013 13mm brass bib tap with spigot nozzle and No. 12.50 SN 13
a hole drilled through the shaft for the tap
head for locking purpose
N 017 13mm chromium plated brass 2-way bib tap No/ 18.00 SN 17
N 018 15mm chromium plated brass 2-way bib tap No. 24.00 SN 18
(lever head type)
N 022 13mm matt steel finish garden bib tap with No. 11.40 SN 22
spigot nozzle and lever head
N 023 15mm matt steel finish garden bib tap with No. 21.10 SN 23
spigot nozzle and lever head
Pillar Tap
N 028 15mm chromium plated pillar tap with swivel No. 21.70 SN 28
swan neck
N 029 20mm chromium plated brass pillar tap for No. 32.00 SN 29
long bath
Gland Nut
Rubber Washer
N 038 Rubber washer for 13mm to 25mm stop cock or bib No. 1.10 SN 38
tap in replacement.
N 039 Rubber washer for 30mm to 50mm stop cock or bib No. 1.40 SN 39
tap in replacement.
Gate Valve
N 048 80mm diameter ductile/cast iron gate valve including No. 133.40 SN 48
washers, gaskets, bolts and nuts
N 049 100mm diameter ductile/cast iron gate valve including No. 164.50 SN 49
washers, gaskets, bolts and nuts
N 050 50mm diameter DZR type brass gate valve including No. 33.10 SN 50
washers, gaskets, bolts & nuts, etc
N 051 40mm diameter DZR type brass ball valve No. 33.20 SN 51
N 052 Lever stem to 50mm diameter equilibrium ball float No. 13.50 SN 52
valve
Sluice Valve
N 053 150mm diameter cast iron sluice valve with flanged No. 261.70 SN 53
ends and wheel head
N 060 Exposed water closet flush valve with 240mm x No. 177.70 SN 60
408mm `L' flush pipe, vacuum breaker and stop
valve for back inlet water closet
N 061 Exposed water closet flush valve with 280mm long No. 177.70 SN 61
supply pipe, vacuum breaker and stop valve for top
inlet water closet bowl
N 062 Water closet water-saving flush valve with 470mm x No. 184.70 SN 62
320mm long `T' flush pipe, vacuum breaker and stop
value
N 063 Water closet water-saving flush valve with 280mm No. 186.80 SN 63
long flush pipe, vacuum breaker and stop valve
N 064 Water closet concealed flush valve with flushing pipe No. 93.00 SN 64
and 32mm diameter elbow coupling
N 065 Water closet water-saving concealed flush valve with No. 220.00 SN 65
flushing pipe and 32mm diameter elbow coupling
N 066 PUB approved stainless steel sensor operated flush No. 512.00 SN 66
valve complete with stainless steel outlet flush
pipes to water closets including fixing and jointing
to water supply and fittings as specified
N 069 Urinal concealed flush valve with 16mm diameter `L' No. 99.90 SN 69
shape flushing pipe, front cap cover, but without spud
N 070 Urinal concealed flush valve with 16mm diameter `L' No. 111.00 SN 70
shape flushing pipe, front cap cover, but with spud
N 072 Repair automatic (electronic) sensor for flush valve Job 16.00 SN 72
(Parts measured separately)
N 073 Flush valve assembly (Body, 'O' ring, Adaptor No. 20.30 SN 73
and Handle cap)
N 079 Stopcock assembly complete with handle, 'O' ring No. 44.60 SN 79
stopcock cap, 'O' ring, seal check valve and rubber
washer
N 085 Push Button assembly complete with cap nut, No. 12.20 SN 85
hexagonal nut and switch
N 086 Solenoid assembly complete with valve, coil, plug, No. 28.30 SN 86
rubber washer and screws (E-Ring)
N 088 Sensor assembly complete with studs and nuts No. 34.40 SN 88
N 098 Casing complete with front cover, back cover and No. 23.30 SN 98
screws
N 099 Cover frame complete with screws (and magnet) No. 17.30 SN 99
N 104 Elbow adaptor (90 degree straight, T-Elbow) No. 4.70 SN 104
N 108 Miniature stop valves for basin and cistern No. 4.70 SN 108
Flow Regulator
N 109 15mm diameter approved constant flow regulator of No. 5.60 SN 109
12 litres per minute
Rubber Hose
Floor Trap
P 002 Cast iron deep seal floor trap complete with hinged No. 85.30 SP 2
grating cast iron hopper and with vertical side or
back inlets and 75mm outgo pipe including hacking
existing damaged trap and jointing to existing pipe
P 003 150mm cast iron hopper connecting piece not No. 13.20 SP 3
exceeding 300mm long including hacking existing
hopper and all necessary jointing
P 004 100mm diameter cast iron floor trap or floor waste No. 59.60 SP 4
with hinged grating, hopper and 75mm outgo and
concrete surround (at ground floor slab) including
hacking to remove existing damaged trap/waste and
jointing to pipe.
P 005 150mm diameter cast iron floor trap with hinged No. 78.10 SP 5
grating, hopper and 100mm diameter outgo and
concrete surround (at ground floor slab) including
hacking to remove existing damaged trap and jointing
to pipe.
Waste Trap
P 006 100mm UPVC adjustable 'S' trap complete with No. 15.10 SP 6
hopper, vent socket and grating including jointing to
waste pipe
P 007 100mm UPVC adjustable 'P' trap complete with No. 12.70 SP 7
hopper, vent socket and grating including jointing to
waste pipe
Bottle Trap
P 023 6mm thick 150mm square UPVC grating with/without No. 4.60 SP 23
perforation with hinges/frame including
bedding in cement mortar
P 024 2mm thick 150mm galvanised steel square hinged No. 6.80 SP 24
grating with/without perforation for apron gulley
including embedding in cement mortar
Dome-Shaped Grating
P 048 75mm diameter cast iron dome grating including No. 14.90 SP 48
embedding in cement mortar
P 049 100mm diameter cast iron dome grating including No. 16.20 SP 49
embedding in cement mortar
P 050 150mm diameter cast iron dome grating including No. 12.30 SP 50
embedding in cement mortar
Strainer
P 051 Purpose made perforated 18G aluminium strainer not No. 84.00 SP 51
exceeding 300mm diameter for street gulley trap
excluding cast iron grating
P 053 Cast iron strainer for interceptor trap, rectangle/ No. 86.70 SP 53
square type not exceeding 0.72m2
P 054 100mm diameter ductile iron `Y' - pattern trap No. 245.30 SP 54
including flanges and cutting, removing existing
pipe etc
P 056 UPVC anti-mosquito device (98mm) with body, filter, Set 10.80 SP 56
cover and gully trap grating
P 057 UPVC anti-mosquito device (98mm) with body, filter No. 6.40 SP 57
and cover only
P 059 Auto floating ball cover fitting c/w lightweight PVC No. 7.50 SP 59
ball
Q 004 Re-caulk joints of 100mm diameter cast iron rising Joint 7.30 SQ 4
main pipe including raking out and providing
additional spun yarn and molten lead if required
in upright position
Q 005 Re-caulk joints of 100mm diameter cast iron rising Joint 6.60 SQ 5
main pipe on level ground including raking out and
providing additional spun yarn and molten lead if
required
Q 006 Re-caulk joints of 150mm diameter cast iron rising Joint 7.80 SQ 6
main pipe including raking out and providing
additional spun yarn and molten lead if required in
upgright position
Q 007 Re-caulk joints of 150mm diameter cast iron rising Joint 7.30 SQ 7
main pipe on level ground including raking out and
providing additional spun yarn and molten lead if
required
Q 008 Cut 100mm diameter cast iron rising mains and Joint 35.30 SQ 8
jointing with Gilbault coupling
Q 009 Cut 150mm diameter cast iron rising mains Joint 45.70 SQ 9
and jointing with Gilbault coupling.
Q 011 Repair leaking joints of galvanised service pipe not No. 2.00 SQ 11
exceeding 25mm diameter
Q 019 Bore holes in water service pipes for use as bin Job 4.30 SQ 19
chute sparge pipes at 50mm centre to centre
(per chute)
Q 020 Take down copper inlet pipe to w.c. cistern for Job 3.90 SQ 20
clearing and rodding including refixing to position and
make good work disturbed
Repair to WC
Q 022 Hack hole through wall or floor slabs not exceeding Job 13.10 SQ 22
150mm thick to form chase for entry of water service
pipe (pipe measured separately)
Q 025 Clear obstructions in floor traps, gulley traps and Job 4.60 SQ 25
urinal trap
Q 028 Clear obstructions or for flushing the sullage water or Job 6.00 SQ 28
rain water down pipes right through to sumps or
house drains
Q 032 Repair 80mm to 100mm ductile/cast iron gate valve No. 10.10 SQ 32
leakage including renewing gaskets/servicing of
pressure reducing valve 32mm to 50mm diameter
Q 035 Adjust stop cocks to tilt towards any direction Job 2.00 SQ 35
specified including making good any damaged or
affected piping work
Q 036 Clean white glazed w.c. pans or other white glazed Job 1.60 SQ 36
sanitary fittings to a satisfactory finish free from stain
Q 038 Repair leaking joints of stainless steel pipe not No. 5.00 SQ 38
exceeding 42mm diameter
Q 039 Repair leaking joints of stainless steel pipe above No. 5.10 SQ 39
42mm diameter but exceeding 75mm diameter
Q 040 Repair leaking joints of upvc pipe from 50mm No. 5.20 SQ 40
diameter to 150mm diameter.
Q 041 Repair leaking joint of dry riser pipe to comply with No. 16.90 SQ 41
FSSD regulation including testing
Locking Device
Q 044 2mm thick galvanised steel locking device of approved No. 15.50 SQ 44
box or cylindrical pattern for staircase taps, bin
chute stopcock etc complete with chain including all
necessary welding
Q 046 Modification of existing locking device for water taps No. 56.70 SQ 46
to incorporate self locking mechanism /
"push-on" type complete with 2 keys (key-alike)
Q 047 200mm x 200mm x 150mm x 1.6mm thick mild steel No. 40.90 SQ 47
box with electro-galvanised coated with 1 coat
of epoxy baked powder coated paint c/w locking
mechanism
Miscellaneous Repairs
Q 052 Break through roof slab to form operning for entry of Opening 13.10 SQ 52
water service pipes and make good all work
disturbed including waterproofing work on completion
of pipe installation to the entire satisfaction of the
roofing specialist. (waterproofing work carried out
by Specialist to be measured separately)
Q 053 Seal up sand holes in cast iron pipes with metalic No. 5.10 SQ 53
epoxy resin as per manufacturer's instruction
including touching up paint to match existing
Q 056 Supply labour and equipment for locating leaks in Test 161.00 SQ 56
underground pipe
Q 058 Repair leaking cast iron pipe at joint of UPVC pipe Joint 6.40 SQ 58
exceeding 75mm but not exceeding 150mm
diameter
Q 059 Replace lock only to tap box of refuse chute flushing No. 13.80 SQ 59
system & civil defence tap to match existing
Q 060 Break up existing long bath wall to form opening not Job 36.90 SQ 60
exceeding 0.05m2, complete with new precast
concrete maintenance access door, finish with wall
tiles to match existing including carting away of
debris
Q 061 Break up displaced stool support of water mains and No. 13.40 SQ 61
provide new 305mm x 305mm brick stool support not
exceeding 380mm high including rendering sides and
haunching top in cement mortar (1:3)
Q 062 Repair leak in concrete surround of gulley trap, cast Job 3.60 SQ 62
iron soil pipes, etc. with waterproofed cement mortar
Q 065 Rake out existing pointing at joint between sink and Job 3.60 SQ 65
wall and repoint in white cement
Q 066 Rake out existing pointing at joint between long bath Job 11.50 SQ 66
and wall and repoint in white cement
Q 067 Form 75mm high cement surround at base of w.c. Job 3.90 SQ 67
cistern flush-pipe and squat pan joint to cure leak
R 002 Clear, flush with water, clean, including scrape Job 3.30 SR 2
hardened oil sludge, debris etc, off inspection
chamber using high pressure water jetting, electro-
mechanical equipment with minimum discharge
pressure of 4000 PSI and vacuum cleaning
equipment (Including main and branch half round
channels within inspection chambers)
R 003 Clear, flush with water, clean, including scrape Job 5.10 SR 3
hardened oil sludge, debris, etc off street gulleys and
strainers using high pressure water jetting and
electro-mechanical equipment with minimum
discharge pressure of 4000 psi
R 004 Clear, flush with water, clean, including scrape Job 134.10 SR 4
hardened oil sludge, debris etc, off grease trap/
interceptor using high pressure water jetting and
electro-mechanical equipment with minimum
discharge pressure of 4000 PSI including vacuum
cleaning of solids and semi solids
R 008 Pump up and remove oil waste from oil interceptors No. 19.20 SR 8
in industrial workshops
R 009 Flush the 100mm diameter ductile iron `Y' pattern No. 3.30 SR 9
trap
R 010 Clear waste and sludge from oil interceptors in Drum 39.90 SR 10
industrial estates collected in metal drum (209 litres/
46 gallons) and cart away to NEA's dumping ground
in accordance with NEA's requirement and including
dumping fee
S 003 50mm diameter galvanised steel spring clip with No. 2.90 SS 3
nylon nettings cover at outlet of overflow pipe
S 004 100mm diameter galvanised steel spring clip with No. 3.10 SS 4
nylon mosquito mesh cover at outlet of overflow pipe
S 008 Seal up gaps along edges between covers and tanks m2 1.10 SS 8
with new nylon mosquito mesh of approved quality
with approved non-toxic sealing compound
S 012 Repair of leaky joints of link pipe jointing to water Joint 8.40 SS 12
storage tanks including necessary gaskets, sealing
compound etc
S 014 Rolled steel joists for support of tanks including bolts, Kg 1.30 SS 14
fixing and painting
S 015 Approved inspection cover to mild steel water tank to No. 29.70 SS 15
match existing
S 018 Dismantle bulging water tank panel and refix to Panel 6.10 SS 18
proper shape (provision of additional angle steel
bracings/stays, flush and refilling water, sterilize and
test water sample measured separately)
S 019 100mm galvanised iron jam nut complete with No. 5.90 SS 19
washer, etc. to water tank
S 021 Repair leakage at jamb nut (flushing and refilling No. 6.80 SS 21
water, sterilize and test water sample measured
separately)
S 022 Dismantle and remove from site existing damaged Cover 32.30 SS 22
inspection cover including the 150mm high four-sided
galvanised steel boxing to the access hole and
replace with 0.559mm thick galvanised steel cover
overall size 490 x 490mm including boxing up the
access hole with 150mm high x 0.559mm thick
galvanised steel including pop-riveting
S 024 100mm diameter PVC cap with 100mm diameter Job 27.00 SS 24
UPVC bend (any angles) (SS 213) plain and 100mm
diameter testing openings (F & F) including removal
of existing nylon netting and drill holes of different
sizes to PVC cap and providing of allen type screw
S 027 Flush suction/storage tanks and refilling with clean No. 3.30 SS 27
water upon completion (Applicable for repainting of of Tank
mild steel tank or where washing of tank is not
required)
S 031 Clean and remove rust stains from external surface m2 0.35 SS 31
of stainless steel water tanks
S 032 Flush steel strainer located after PUB Bulk Meter No. 3.90 SS 32
including dismantling and refixing
S 034 Paint internal surfaces and cover of mild steel water m2 2.50 SS 34
tanks including bracing with one coat of water based
converter. (Surface preparation measured separately)
S 035 Paint internal surfaces and cover of mild steel water m2 4.70 SS 35
tanks including bracing with two finishing coats of
water based paint. (Surface preparation measured
separately)
S 037 Paint external surfaces of mild steel water tanks with m2 2.40 SS 37
one coat of rust convertor of water based.
(Surface preparation measured separately)
S 039 Paint external surfaces of mild steel water tanks with m2 2.20 SS 39
one finishing coat water based paint.
(Surface preparation measured separately)
S 040 Paint external surfaces of mild steel water tanks with m2 3.60 SS 40
one finishing coat of epoxy based paint.
(Surface preparation measured separately)
S 042 Replace FRP/GRP panel for water tank (flush and panel 406.90 SS 42
refilling water, sterilize and test water sample shall
be measured separately)
T 001 13mm diameter light guage metal flexible inlet tube No. 1.80 ST 1
to cistern/basins and taps complete with connectors
T 002 13mm rubber washer to tap and stop cock No. 0.40 ST 2
T 012 13mm diameter DZR type brass stop cock No. 8.40 ST 12
T 014 13mm diameter copper piping 300mm long with No. 3.30 ST 14
connectors at both ends for fittings
T 018 13mm brass bib key tap including detachable spindle No. 7.50 ST 18
head
(U) DAYWORKS
Labour
Plant
U 006 Motor Lorry (Pick-up) not more than 2.50 tonne Hr 18.30 SU 6
including fuel and driver
U 007 Motor Lorry 3 tonne size including fuel and driver Hr 25.60 SU 7