Professional Documents
Culture Documents
MPU/SRU 1:1
redundancy
Switch 6+2 FULLMESH FULLMESH
redundancy
MPU/SRU/SFU/PFU/PIU boards, power supply modules, and fan modules
Hot swapping support hot-swapping
Air inlet
b
a Ethernet
General Service card GSU Management Process Unit MPU
Power/CLK c Power/CLK
k Ethernet Maintenance
RS232
Service Switch Control p switch unit Management
processi interfac l unit ZXR10-OAM
2.048MHz
ng unit e unit a Control
HSSL n System 2.048Mbps
management and
e Clock TOD/PP1S
maintenance unit module
1 M S
2
8
Power
Power Fan
supply module
module
.. 5
2
1 1
2
3
4
b
a Ethernet
General Service card GSU Management Process Unit MPU
Power/CLK c Power/CLK
k Ethernet Maintenance
RS232
Service Switch Control p switch unit Management
processi interfac l unit ZXR10-OAM
2.048MHz
ng unit e unit a Control
HSSL n System 2.048Mbps
management and
e Clock TOD/PP1S
maintenance unit module
1 M S
2
5
Power
Power Fan
supply module
module
3
2
1 1
2
MPU
2 MPU Boards,1:1 redundant backup
MPU
2 MPU Boards,1:1 redundant backup
1
2
3
b Ethernet
General Service card GSU a Management Process Unit MPU
Power/CLK c Power/CLK
k Ethernet Maintenance RS232
Service Switch Control p switch unit Management
processin interface l ZXR10-OAM
a unit 2.048MHz
g unit unit HSSL Control System
n 2.048Mbps
e management and Clock TOD/PP1S
maintenance module
1 unit M S
2
3
Power
Fan module
Power
supply
module
2
1
1
2
b
a Ethernet
General Service card GSU Management Process Unit MPU
Power/CLK c Power/CLK
k Ethernet Maintenance
RS232
Service Switch Control p switch unit Management
processi interfac l unit ZXR10-OAM
2.048MHz
ng unit e unit a Control
HSSL n System 2.048Mbps
management and
e Clock TOD/PP1S
maintenance unit module
1 M S
2
8
Power
Power Fan
supply module
module
.. 5
2
1 1
2
3
4
1
2
3
b Ethernet
General Service card GSU a Management Process Unit MPU
Power/CLK c Power/CLK
k Ethernet Maintenance RS232
Service Switch Control p switch unit Management
processin interface l ZXR10-OAM
a unit 2.048MHz
g unit unit HSSL Control System
n 2.048Mbps
e management and Clock TOD/PP1S
maintenance module
1 unit M S
2
3
Power
Fan module
Power
supply
module
2
1
1
2
P P P P S S S P P P P
F F F F R F R F F F F
U U U U U U U U U U U
S
F
U
0 1 2 3 4
FAN FAN FAN FAN FAN
0 1 2 3
PWR PWR PWR PWR
M6000-
M6000-
18S
2S10
M6000-2S4
The ACT indicator for the first gigabit electrical interface. It flashes
ACT Yellow
when there are packets being sent and received.
Button Description
Function button. It is used to collect the system operation
FUN state and configuration. Press this button for more than 6
seconds.
RST Reset button. It is used to reset this board.
Active/standby switchover and hot swapping button. When
this board is active, this button is an active/standby
switchover button. Press this button to switchover between
EXCH/OFL the active and the standby boards manually. When this
board is standby, this button is a hot swapping button.
Press this button for more than 6 seconds until the OFL
indicator is on and then the board can be removed.
Ring button. By pressing it for more than 6 seconds, the
RING
ring stops.
MPU board:M6KS-MPU-A
Manages and maintains the router
Processes dynamic routing protocols
Provides the reset function, in-
position signal collection and
active/standby indicator signals for
SFU boards, PFU boards, and ESU
boards
Manages line interface boards
Provides interfaces for operation and
management of the router system
Provides the system environment
monitoring function
System RUN Green System operation indicator. It flashes when the system is
Operation operating properly.
State
ALM Red System alarm indicator. It is on when a fault occurs and off when
the system state is normal.
ACT Green System active indicator. It is on when the board is active and off
Indicators when the board is standby.
Button Descrption
FUN Function button. It is used to collect the system operation state and configuration. Press
this button for more than 6 seconds.
Buttons
RST Reset button. It is used to reset this board.
EXCH Active/standby changeover button. It is used to change over between the active board
and the standby board manually. When the board is a standby board, this button is a
hot-plug button.
© ZTE Corporation. All rights reserved
Technical Specifications of M6KS-MPU-A and
M6KS-MPU-1A
Parameter Specification
Silk screen name M6KS-MPU-A M6KS-MPU-1A
Dimensions
(W×H×D) 197.2mm×35.16mm×515.4mm 197.2mm×35.16mm×515.4mm
Power
consumption 50W 65W
SRU Buttons
Button Description
FUN Function button. It is used to collect the system operation state and
configuration. Press this button for more than 6 seconds.
EXCH/OFL Active/standby changeover and hot-plug button. When this board is active,
this button is an active/standby changeover button. Press this button to
change over
between the active and the standby boards manually. When this board is
standby, this button is a hot-plug button. Press this button for more than 6
seconds until the OFL indicator is on and then the board can be removed.
RING Ring button. By pressing it for more than 6 seconds, the ring stops.
© ZTE Corporation. All rights reserved
M6KS-SRU-A Panel Description - Interfaces
Mark Type Description
OAM RJ45 Download the version file and monitor network ports.
QX RJ45 Debugging interface.
CONSOLE RJ45 Connect to a back-end management terminal for operation and
maintenance through a tool, for example, HyperTerminal.
AUX RJ45 Connect to a Modulator-Demodulator (MODEM) for remote
management.
USB USB Interface for a USB storage device.
ALM IN RJ45 Alarm input interface
ALM OUT RJ45 Alarm output interface.
LAMP RJ45 Interface for turning on the alarm indicator.
GPS IN RJ45 External interface for GPS clock input.
GPS OUT RJ45 External interface for GPS clock output.
CLK1 SMB External interface for 2.048 MHz or 2.048 Mbit/s clock input/output.
CLK2 SMB External interface for 2.048MHz or 2.048 Mbit/s clock input/output.
Button Description
Function button. It is used to automatically collect system
FUN
information.
RST Reset button. It is used to reset this board.
SFU Buttons
Button Description
OFL Hot-plug button. To plug out this board when the device is powered
on, it is necessary to press this button for more than 6 seconds.
When the OFL indicator is on, the board can be removed.
SFU Indicator
Indicator Color Description
SFU Buttons
Button Description
OFL Hot-plug button. To plug out this board when the device is powered
on, it is necessary to press this button for more than 6 seconds.
When the OFL indicator is on, the board can be removed.
M6KS-PFU-10-A4 Four half-height (197.4 mm × The PIUs include GE, OC3 CPOS,
OC3/OC12 POS, OC48 POS, OC12
4) CPOS, CE1, OC3 ATM and OC12
ATM. The throughput of each
quarter-height PIU is 10Gbps. The
M6KS-PFU-10-A4 board provides
10 G bidirectional network
processing ability.
M6KS-PFU-40-A2 Panel
The indicators and
buttons of PFU
Board are the
same as SFU
M6KS-PFU-10-A4 Panel
RPS-20GE-SFP
RPS-01XGE-SFP+
RPS-02XGE-SFP+
RPS-04P3/P12-SFP
RPU-01XLGE-CFP
RPU-01CGE-CFP
RPH-03XLGE-QSFP+-S
RPH-01CGE-CFP-S
RPN-01XGE-SFP+-S
RPN-02XGE-SFP+-S
RPN-01P192-SFP+
RPN-02P192-SFP+
RPN-24CE1-DB50-75
RPN-24CE1-DB50-75-CES
RPN-24CE1-DB50-120
RPN-24CE1-DB50-120-CES
-48 V RTN
Power supply input (+)
Switch power supply Handle
cable input
Indicator end
Weight 1.2kg
Switch Handl
e
ZXR10 M6000-18S supports N+1 or N+N redundancy for the DC power supply modules.
Parameter Specification
Dimensions (Height × Width × Depth) 19.9 mm ×197.2 mm ×194.5 mm
Weight 0.9 kg
Rated input voltage -48 V DC / -60 V DC
Input voltage range -38.4 V DC to -72 V DC
Rated input current 28 A / 22.3 A
Rated output voltage -12 V DC / -48 V DC
Maximum output current 43 A / 20.3 A
Maximum output power 516 W / 780 W
fan modules
Horizontal Air Filter
Air Filter
© ZTE Corporation. All rights reserved
ZXR10 M6000-S Fan Module
Indicators on the ZXR10 M6000-5S Fan Module Panel
Parameter Description
Power consumption 22 W
Maximum wind
410 Pa
pressure
Maximum air volume 300 cfm
Air Filter
Air Filter
Replaced
© ZTE Corporation. All rights reserved
Heat Dissipation System – M6000-5S/3S AC
Air Filter
Each AC power supply module
has two fans for independent
heat dissipation.
Air Filter
Replaced
© ZTE Corporation. All rights reserved
Heat Dissipation System – M6000-18S
Air Directions
of Network
Processing
Board Slots
Air Directions of
SFU Board Slots
Air Directions of
Power Supply
Module Slots
Layer 2 functions
VLAN /QinQ /Super VLAN /MAC /Smartgroup /LACP/Broadcast restriction
/ARP/IGMP Snooping /Ethernet OAM
Layer 3 functions
IPv4/IPv6/ PIM-SM/PIM-DM/ IGMP
MPLS
MPLS L2 VPN /MPLS L3 VPN /MPLS TE / MPLS OAM
QoS
Traffic Classification/Traffic Monitoring and Shaping/Congestion
management/Congestion avoidance/
H-QoS/QPPB
Reliability
MPLS-TE tunnel end to end path protection/ MPLS-TE FRR/ BFD/VPN FRR/ IP
FRR/ LDP FRR/ Graceful Restart/ VRRP / NSR / Non interrupted upgrade
Security
MPLS tunnel /GRE tunnel /IPsec tunnel
Anti attack /CPU Security / Advanced security features
OAM
Site1
PE/
PE&CE
Site2
CE
Site3
CR CR
CMS center
IP MAN BSC
RNC
Core layer
BRAS
M6000-S Access control
SR SR layer of RAN
Access layer
CE/PTN
Switch xDSL PON
Video Business
Wimax WLAN HSI surveillance IPTV Node B BTS Leased Line
Resident Service Carrier-grade and Leased Line Services
TG/SG
VoIP VPN
Scheme A Scheme B
M6000-S M6000-S
VRRP EBGP/Static
M6000
L2 switch
VRRP
AG AG AG AG AG
WCN Site
switch
CS PS BOSS &
Application
Mobile service SLA guarantee via VPN QoS
Tunnel mode in RFC 3270: uniform, short pipe and pipe modes
Flexible mapping
Traffic engineering