Professional Documents
Culture Documents
Pid Temperature Control Unit: The Dev Ce W TH One Relay
Pid Temperature Control Unit: The Dev Ce W TH One Relay
1 B- 8
Ser�al Commun�cat�on PO1 PO1 PO1
5A@250V
AL1 AL1 AL1
2 A+ 9 AL1 / PO2
(Alarm Output 1 or
C Process Output 2)
3 SSR Output 10
PO1 12V Press Program button Enter Password w�th �ncrement Approve password
(Process Output 1)
4 Max. 10mA 11
to access password screen. or decrement buttons. w�th Enter button
5 12
N 6
Process
Supply 13
Input °C °C °C
*4 °C °C
*5 °C
*6 °C
*7
PT-100
TC
°F °F °F °F °F °F °F
Voltage L
7 14
Supply 1A T Eco PID PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
Sw�tch Fuse AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
1 B-
NO
8 AL2 / PO2
Ser�al Commun�cat�on (Alarm Output 2 or PO1 PO1 PO1 PO1 PO1 PO1 PO1
Process Output 2)
AL1 AL1 AL1 AL1 AL1 AL1 AL1
5A@250V
5A@250V
(RS485, Modbus RTU) NO AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
2 A+ 9
AL1
C (Alarm Output 1)
3 SSR Output 10
PO1 12V °C °C °C °C °C °C °C
(Process Output 1) °F °F °F °F °F °F °F
Eco PID
4 Max. 10mA 11
PO1 PO1 PO1 PO1 PO1 PO1 PO1
N 6 13
Process
Eco PID, PID Temperature Control Un�t Supply Input
PT-100
TC
Voltage L
- 3 d�g�t process (PV) and 4 d�g�t set (SV) d�splay Supply 1A T
7
Eco PID
14 °C
°F
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F
°C
°F
c
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
To reduce the effect of electr�cal no�se on dev�ce, low voltage l�ne (espec�ally sensor
- Adaptat�on of PID Coeff�c�ents to the system w�th Self-Tune and Auto-Tune �nput cable) w�r�ng must be separetely from h�gh current and voltage l�ne. If poss�ble,
- Programmable Heat�ng or Cool�ng Funct�ons for Control Output use sh�elded cable and sh�eld must be connected to ground only one s�de.
°C
°F
°C
°F *1 °C
°F
°C
°F
°C
°F
°C
°F
Eco ser�es temperature controllers are des�gned for measur�ng and controll�ng a Max�mum 9 mm / 0.35 �nch
temperature value. They can be used �n many appl�cat�ons w�th the�r TC and RTD °C
°F
°C
°F
°C
°F
°C
°F
°C
°F
48 mm / 1.89 �nch
°C
They are ma�nly used �n glass, plast�c, petro-chem�stry, text�le, automot�ve and mach�ne °F
ON-OFF, P, PI, PD, PID and Self Tune/Auto Tune PID funct�ons.
°F °F °F °F °F
PO1 AL1
SPECIFICATIONS PO2
/
AL2 PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
PO1
AL1
AL2 / PO2
Measurement Range: Please refer to process �nput type select�on �n process menu °F °F °F °F
Thermocouple (TC):( ± 0.25% of full scale or ± 3ºC, wh�ch one �s greater) ±1 d�g�t max.
Thermores�stance (RTD):( ± 0.25% of full scale or ± 2ºC, wh�ch one �s greater) ±1 d�g�t °C °C
*2,3
Panel Mount�ng
°F °F
*3 - Soft Start Control Output and Soft Start Control T�me parameters �s not act�ve �f parameter
L�ne Compensat�on: Max�mum 10 Ohm �s set as .
Sensor Break Protect�on: Upscale make sure that the cutout �s of the r�ght s�ze. *4 - PID control parameters are not act�ve unless parameter �s set as .
°C
*2,3
2- Check front panel gasket pos�t�on. *5 - Alarm-2 parameters are not act�ve �f parameter �s set as .
°F
Sampl�ng Cycle: 0.1 second *6 - Commun�cat�on parameters are not act�ve on dev�ces have no commun�cat�on module.
Input F�lter: Programmable °C
°F
3- Insert the dev�ce through the cutout. If the PO1
AL1
AL2 / PO2 *7 - If �s d�fferent from 0 and user enters to program menu w�thout enter�ng the password
Control Form: ON/OFF, P, PI, PD or PID (Control form can be programmed by the user) Ec
o
mount�ng clamps are on the un�t, put out them Prot menu �s not shown.
Note: User can ex�t from any parameter screen w�thout sav�ng the values by press�ng button. If
PO
1
OUTPUT
PO 1
2
AL
2
/
115VV (±15%) 50/60Hz - 2VA screen. Or eas�ly press button for 3 seconds* �n ma�n screen.
unt�l the dev�ce completely �mmob�le w�th�n the 2- Observe that bl�nks �n set d�splay.
100-240VV 50/60Hz - 2VA
PO1 PO1 PO1 PO1
°C AL1 AL1 AL1 AL1
°F
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
*Only Auto tune can be started by th�s way.
panel.
Ec
o
parameter �n menu;
ENVIRONMENTAL RATINGS and PHYSICAL SPECIFICATIONS PO1
AL1
PO1
AL1
PO1
AL1
PO1
AL1
Then tune operat�on �s canceled, dev�ce cont�nues to run w�th former
AL2 / PO2 AL2 / PO2 AL2 / PO2 AL2 / PO2
Note-1: User can ex�t from set value sect�on w�thout sav�ng the values by press�ng button. If no
Panel CutOut: 46 x 46 mm operat�on for 120 seconds, dev�ce automat�cally ex�ts from Set Value sect�on.
Note-2: Set value can be adjusted between Set Value Low and H�gh L�m�t ( - ). Introduct�on Brochure. ENG EcoPID 01 V04 10/19
Alarm
: Process Menu Parameters : Alarm-2 Menu Parameters (Only for dev�ces w�th two relays) Output Process Alarm Process Process Alarm
Warranty
Set Set Set Set Set
: Process �nput type select�on; (Default: ) Modbus Address: 40004 Alarm-2 menu parameters can be seen only �f parameter �s . EMKO Elektron�k warrants that the equ�pment del�vered �s free from
: J type (Fe,Cu,N�) Thermocouple , -199ºC,900ºC ; -199ºF,999ºF : Alarm-2 set value. (Default: 400) Modbus Address: 40046
Dev�at�on Band defects �n mater�al and workmansh�p. Th�s warranty �s prov�ded for a
: J type (Fe,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Alarm-2 hysteres�s value. It can be adjusted from %0 to %50 of the Scale
: K type (N�,Cr,N�) Thermocouple , -199ºC,999ºC ; -199ºF,999ºF ( - ). (Default: 0) Modbus Address: 40047 Alarm Alarm Alarm
per�od of two years. The warranty per�od starts from the del�very
: K type (N�,Cr,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Alarm-2 type select�on. (Default: ) Modbus Address: 40048
Hysteres�s Hysteres�s
Process Value
date.
: R type (Pt13%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF : Alarm-2 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum Alarm Th�s warranty �s �n force �f duty and respons�b�l�t�es wh�ch are
: R type (Pt13%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF to alarm-2 set h�gh l�m�t. (Default: 0) Modbus Address: 40049 Output Process Alarm Process Alarm
Set Set
Process
Set Set Set determ�ned �n warranty document and �nstruct�on manual performs
: S type (Pt10%RhPt) Thermocouple , 0ºC,999ºC ; 32ºF,999ºF : Alarm-2 set h�gh l�m�t parameter. It can be adjusted from alarm-2 set low l�m�t to
: S type (Pt10%RhPt) Thermocouple , 0.0ºC,99.9ºC ; 32.0ºF,99.9ºF operat�on scale max�mum. (Default: 500) Modbus Address: 40050 by the customer completely.
: T type (Cu,Cu,N�) Thermocouple , -199ºC,400ºC ; -199ºF,752ºF : Alarm-2 on delay t�me. It can be adjusted from 0 to 9999 seconds. (Default: 0)
Dev�at�on Range
Alarm
Ma�ntenance
: T type (Cu,Cu,N�) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF Modbus Address: 40051 Alarm Alarm
: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -150ºC,800ºC ; -199ºF,999ºF : Alarm-2 off delay t�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher Hysteres�s Hysteres�s Repa�rs should only be performed by tra�ned and spec�al�zed
Process Value
: L type (N�,Cr,Co / N�,Fe,Mn,Cu) Thermocouple , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF than 9998, �s seen on the screen and Alarm Latch�ng Output �s selected. In Alarm personnel. Cut power to the dev�ce before access�ng �nternal parts.
: Cu-50 , -199ºC,200ºC ; -199ºF,392ºF alarm latch�ng output mode �n order to make pass�ve alarm outputs, press enter Output Process Alarm Process Do not clean the case w�th hydrocarbon-based solvents (Petrol,
: Cu-50 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF button at ma�n screen. (Default: 0) Modbus Address: 40052 Set Set Set
: Pt-100 , -199ºC,650ºC ; -199ºF,999ºF Tr�chlorethylene etc.). Use of these solvents can reduce the
: Pt-100 , -19.9ºC,99.9ºC ; -19.9ºF,99.9ºF : Commun�cat�on Parameters (Only for dev�ces w�th RS-485 com.) Dev�at�on Range mechan�cal rel�ab�l�ty of the dev�ce. Use a cloth dampened �n ethyl
: Un�t Select�on. or can be chosen. (Default: ) Modbus Address: 40005 : Commun�cat�on access�ng address of dev�ce. (Default: 1) Modbus H�gh Alarm alcohol or water to clean the external plast�c case.
Alarm
: Operat�on Scale m�n�mum (Low L�m�t) value. It changes accord�ng to the process Address: 40056 Hysteres�s
�nput type and scale. (Default: -199) Modbus Address: 40006 Process Value Other Informat�ons
: Commun�cat�on Baud Rate. (Default: 3) Modbus Address: 40057
: Operat�on Scale max�mum (H�gh L�m�t) value. It changes accord�ng to the : 1200 Baud Rate. Manufacturer Informat�on:
process �nput type and scale. (Default: 900) Modbus Address: 40007
Error Messages
: 2400 Baud Rate. Emko Elektron�k Sanay� ve T�caret A.Ş.
: Process Set value Low L�m�t. M�n�mum set value �s def�ned w�th th�s parameter. : 4800 Baud Rate.
°C
°F 1-Sensor fa�lure �n analog �nputs. Sensor connect�on �s wrong or there
It can be adjusted between Operat�on Scale m�n�mum and max�mum ( - ) : 9600 Baud Rate. �s no sensor connect�on. Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369
BURSA/TURKEY
a
values. (Default: -199) Modbus Address: 40008
PO1
: Par�ty Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40058 password and wants to change a parameter, the warn�ng message �s Fax: +90 224 261 1912
values. (Default: 900) Modbus Address: 40009 : No Par�ty. shown on the bottom d�splay as shown on the left. Dev�ce does not a
PO1
AL1
: D�splay offset for process value. It can be adjusted from -10% of scale to 10% of : Odd Par�ty. AL2 / PO2
: Def�ne f�lter t�me(sec) for d�splayed value. (Default: 1.0) Modbus Address: 40011 : Stop B�t Select�on for Commun�cat�on. (Default: 0) Modbus Address: 40059 3-If value that �s read from the analog �nput �s lower than process set
: 1 Stop B�t.
PO1
AL1
low l�m�t parameter value ( ), value on the top d�splay starts to bl�nk Dem�rtaş Organ�ze Sanay� Bölges� Karanf�l Sk. No:6 16369
: Control Menu Parameters as shown on the p�cture.
AL2 / PO2
(Default: ) Modbus Address: 40015 : Password for access�ng to the programm�ng sect�on. It can be adjusted from 0 to AL2 / PO2
bl�nk as shown on the p�cture.
a
: Process Type Select�on. It can be (Heat�ng) or (Cool�ng).(Default: ) 9999. If �s 0, password screen �s not seen. If �s d�fferent from 0 and user Order�ng Informat�on
°C
°F
5-If value that �s read from the analog �nput �s lower than sensor scale
Modbus Address: 40016 enters to the menu pages w�thout enter�ng the password, all the menus can be low l�m�t, value on the top d�splay starts to bl�nk as shown on the
: Process Control Type Select�on. It can be or . (Default: ) Modbus observed except protect�on menu . But dev�ce does not allow to do any changes
PO1
p�cture. A B C D E
AL1
AL2 / PO2
6-If value that �s read from the analog �nput �s h�gher than sensor scale
°C
: Hysteres�s value. It can be adjusted from %0 to %50 of the Scale ( - ). : User default parameters. Th�s parameter �s used for sav�ng all parameters to °F
If = , then th�s parameter can be seen. (Default: 3) Modbus Address: 40018 restore later or restore all parameters saved before. If �s chosen, all parameters PO1
h�gh l�m�t, value on the top d�splay starts to bl�nk as shown on the 4 . . . S .
: Sensor Break Output Value. It can be adjusted from %0 to %100. (Default: 0.0) saved before are restored. If �s chosen, all parameters saved to restore later. If
AL1
AL2 / PO2 p�cture.
Modbus Address: 40019 �s chosen, noth�ng �s changed. (Default: ) Modbus Address: 40064 A D�mens�on
: The cho�ce of d�splayed text on process value d�splay when sensor �s broken. : Th�s parameter �s used for restore factory defaults. If �s chosen, factory Installat�on 4 48x48 DIN 1/16
It can be or . (Default: ) Modbus Address: 40020 defaults parameters restored. If �s chosen, noth�ng �s changed. (Default: ) Before beg�nn�ng �nstallat�on of th�s product, please
: Soft Start Set value. Dev�ce operates �n Soft Start mode, unt�l the temperature Modbus Address: 40065 B Supply Voltage
read the �nstruct�on manual and warn�ngs below
c
reaches Soft Start set value. If �s selected, Soft Start mode �s d�sabled. (Default: ) Remove all �nput/output connect�ons on term�nals before restor�ng 1 100-240VV 50/60Hz
Modbus Address: 40021 parameters to user/factory defaults.
carefully.
2 24VW (±%15) 50/60Hz
: Soft Start Control Output. Th�s parameter determ�nes soft start mode control In package, 3 115VV (±%15) 50/60Hz
output percentage. It can be adjusted from %10 to %90. (Default: 10.0) Modbus Modbus Addresses of Dev�ce Operat�on Info. (Read Input Reg�ster)
-One p�ece un�t 5 230VV (±%15) 50/60Hz
Address: 40022 Modbus Address: 30000 D�splayed Temperature Value
: Soft Start Control T�me. Th�s parameter determ�nes soft start mode control t�me. -Two p�eces mount�ng clamp 6 10...30VZ
Modbus Address: 30001 Status of LEDs: b�t.1 ALR1, b�t.2 ALR2, b�t.9 °C
(Default: 1.0) Modbus Address: 40023 -One p�ece �nstruct�on manual 7 24VV (±%15) 50/60Hz
b�t.10 °F, b�t.11 PO2, b�t.12 PO1
Modbus Address: 30002 Status of Dev�ce: b�t.0 Sensor Break Status
9 Customer
: PID Menu Parameters
Alarm Types A v�sual �nspect�on of th�s product for poss�ble damage occured C Outputs-1
PID menu parameters can be seen only �f parameter �s .
Alarm
dur�ng sh�pment �s recommended before �nstallat�on. It �s your 1R 1 x Relay Output (5A@250VV at Res�st�ve Load) (NO,C)
: If tune parameter �s set to or , dev�ce start to calculate PID
parameters automat�cally. (Default: ) Modbus Address: 40027 Output Alarm respons�b�l�ty to ensure that qual�f�ed mechan�cal and electr�cal 2R 2 x Relay Output (5A@250VV at Res�st�ve Load) (NO,NO,C)
Set
: Proport�onal band. It can be adjusted from %1.0 to %100.0. (Default: 10.0) techn�c�ans �nstall th�s product.
Modbus Address: 40028 Process H�gh D Outputs-2
If there �s danger of ser�ous acc�dent result�ng from a fa�lure or defect
: Integral T�me. It can be adjusted from 0 to 3600 second. (Default: 100) Modbus Alarm S SSR Dr�ver Output (Max. 10mA, Max. 12VZ)
�n th�s un�t, power off the system and the electr�cal connect�on of the
Address: 40029 Alarm
: Der�vat�ve T�me. It can be adjusted from 0.0 to 999.9 second. (Default: 25.0)
Hysteres�s dev�ce from the system. E Commun�cat�on
Process Value
Modbus Address: 40030 Alarm The un�t �s normally suppl�ed w�thout a power sw�tch or a fuse. Use 0 None
: Output Control Per�od. It can be adjusted from 0.5 to 150 second. (Default: 1.0) Output Alarm power sw�tch and fuse as requ�red. 485 RS-485 Commun�cat�on
Set
Modbus Address: 40031
Be sure to use the rated power supply voltage to protect the un�t
: Set value offset. (Set + ) �s used as set value �n PID calculat�ons. Th�s
parameter �s used for sh�ft�ng the proport�onal band. It can be adjusted from (- /2) to aga�nst damage and to prevent fa�lure.
Process Low Before comm�ss�on�ng the dev�ce, parameters must be set �n
( /2). (Default: 0) Modbus Address: 40032 Keep the power off unt�l all of the w�r�ng �s completed so that electr�c
Alarm Alarm
accordance w�th des�red use. Incomplete or �ncorrect conf�gurat�on
Hysteres�s
shock and trouble w�th the un�t can be prevented.
: Alarm-1 Menu Parameters Process Value can cause dangerous st�uat�ons.
Alarm Never attempt to d�sassemble, mod�fy or repa�r th�s un�t. Tamper�ng Because of l�m�ted mechan�cal l�fe of relay output contact, SSR
: Alarm-1 set value. (Default: 300) Modbus Address: 40036 Output Process Process Alarm
w�th the un�t may results �n malfunct�on, electr�c shock or f�re. output �s recommended wh�ch the dev�ce use PID control algor�tm.
: Alarm-1 hysteres�s value. It can be adjusted from %0 to %50 of the scale Set Set Set
( - ). (Default: 0) Modbus Address: 40037 Do not use the un�t �n combust�ble or explos�ve gaseous The dev�ce w�th ON/OFF control algor�tm, hysteres�s parameter must
Dev�at�on H�gh
: Alarm-1 type select�on. (Default: ) Modbus Address: 40038 atmospheres. Dur�ng the equ�pment �s putted �n hole on the metal be set a su�table value for your system, to avo�d too much relay
Alarm
: Alarm-1 set low l�m�t parameter. It can be adjusted from operat�on scale m�n�mum Alarm panel wh�le mechan�cal �nstallat�on some metal burrs can cause sw�tch�ng.
to alarm-1 set h�gh l�m�t. (Default: 0) Modbus Address: 40039 Hysteres�s
Vac,
Process Value �njury on hands, you must be careful.
: Alarm-1 set h�gh l�m�t parameter. It can be adjusted from alarm-1 set low l�m�t to Vdc,
operat�on scale m�n�mum. (Default: 500) Modbus Address: 40040
Alarm Montage of the product on a system must be done w�th �t’s mount�ng
Output Vdc or Vac can be appl�ed
: Alarm-1 on Delay T�me. It can be adjusted from 0 to 9999 seconds. (Default: 0)
Process
Set
Alarm
Set
Process
Set clamp. Do not do the montage of the dev�ce w�th �nappropr�ate
Modbus Address: 40041 mount�ng clamp. Be sure that dev�ce w�ll not fall wh�le do�ng the
: Alarm-1 off Delay T�me. It can be adjusted from 0 to 9998 seconds. If �t �s h�gher Dev�at�on Low
montage.
than 9998, �s seen on the screen and alarm latch�ng output �s selected. In alarm Alarm
latch�ng output mode �n order to make pass�ve alarm outputs, press enter button at Alarm
Hysteres�s
It �s your respons�b�l�ty �f th�s equ�pment �s used �n a manner not
ma�n screen. (Default: 0) Modbus Address: 40042 Process Value spec�f�ed �n th�s �nstruct�on manual.