Professional Documents
Culture Documents
JKSSB Je Ce MMC 1 23
JKSSB Je Ce MMC 1 23
co
1
www.gradeup.co
A. B.
C. 2l D. l
Ans. C
3. The main bars in RCC column should be at least
A. 10 mm B. 12 mm
C. 16 mm D. 20 mm
Ans. B
4. The maximum dry density of soil is 15 kN/m 3 at OMC 23%. Find air void (%) of the soil. If
specific gravity of soil is 2.6
A. 10 B. 2
C. 6 D. 12
Ans. C
5. The manometer head (Hm) of a centrifugal pump is given by
A. Pressure head at outlet of pump – pressure head at inlet
B. Total head at inlet total head at outlet
C. Total head at outlet – total head at inlet
D. None of the above
Ans. C
6. The discharge passing over an ogee spillway is given by (where, L is effective length of
spillway crest and H is the total head over the spillway crest including velocity head.)
A. CLH3/2 B. CLH3/2
C. CLH5/2 D. CLH1/2
Ans. A
7. Steel unit generates which of the following Air Pollutants ?
A. Particulate smoke, CO, fluoride B. SO2, NOx, particulate smoke
C. NOx, SO2, particulate D. SO2, Acid Mist
Ans. B
8. Floating car method is a _________
A. speed and delay study. B. spot speed study.
C. origin and destination study. D. accident study.
Ans. A
2
www.gradeup.co
9. The distance between the gauge faces of stock rail and tongue rail at the heel of the switch
is called
A. Heel divergence B. Flange way clearance
C. Switch angle D. Throw of switch
Ans. A
10. Air permeability test is done to measure:
A. Setting time of cement B. Soundness of cement
C. Chemical composition of cement D. Fineness of cement
Ans. D
11. In a transit theodolite, the error due to non-parallelism of axis of telescope level and line
of collimation can be eliminated by
A. reading both verniers.
B. reading different parts of main scale.
C. reading left and right face observations.
D. taking both right and left swing readings.
Ans. C
12. Torque corresponding to a twist of one radian in a shaft over its unit length is called
A. Torsional rigidity B. Torsional stress
C. Flexural rigidity D. Moment of resistance
Ans. A
13. Yield line theory leads to result in
A. Elastic solution B. Lower bound solution
C. Upper bound solution D. Unique solution
Ans. C
14. In case of stratified soil layers, the best equation that can be adopted for computing the
pressure distribution is
A. Skempton’s B. Westergaard’s
C. Prandtl’s D. Rankine’s
Ans. B
15. An inward flow reaction turbine:
A. Impulse turbine B. Francis turbine
C. Pelton turbine D. All the above
Ans. B
16. In a Canal Syphon type Cross Drainage Work
A. canal bed is below the drain
B. canal bed is above the drain
C. canal bed and the drain at the same level
D. canal and the drain crossing at right angles
Ans. A
3
www.gradeup.co
A. B.
C. D.
Ans. A
23. End bearing splices are used for
A. Bars in tension B. Bars in compression
C. Resist torsion D. None of the above
Ans. B
24. Which of the following are true for Pumping in test?
A. This test is economical than pumping out test
B. Its results are more reliable than pumping out test
C. They are conducted just closer to the hole where plumping out test was performed
D. All of the above
Ans. D
4
www.gradeup.co
25. The vertical depth of the centre of pressure, for the inclined plane surface below the
free surface of the liquid is
A. B.
C. D.
Ans. C
26. Water requirement for the crops is equal to
A. Consumptive use
B. Consumptive use + Application loss
C. Consumptive use + Application loss + Special needs for land preparation,
transplantation
D. Consumptive use + Application loss + Surface runoff
Ans. C
27. The units in which both sedimentation & digestion process of sludge take places
simultaneously is
A. skimming tank B. imhoff tank
C. detritus tank D. digestion tank
Ans. B
28. Modulus of subgrade reaction using 30cm diameter plate is obtained as 200N/cm 3. The
value of the same using standard plate will be
A. 500 B. 80
C. 100 D. 200
Ans. B
29. The gauge of a railway track is defined as:
A. The clear distance between inner faces of two rails
B. The clear distance between outer faces of two rails
C. The centre to centre distance between two rails
D. The distance between inner faces of a pair of wheels
Ans. A
30. The carpet area of a residential building may be _________ of plinth area.
A. 15% to 30% B. 30% to 40%
C. 40% to 50% D. 50% to 65%
Ans. D
31. The angle between two plain mirrors of an optic square is ________.
A. 0° B. 30°
C. 45° D. 90°
Ans. C
5
www.gradeup.co
32. A rectangular beam of width 200mm is subjected to a shear force of 40kN. If the maximum
shear stress of the cross section is 2 N/mm2, the depth of the beam should be
A. 100 mm B. 150 mm
C. 200 mm D. 225 mm
Ans. B
33. The negative moment reinforcement are provided at least
A. 1/5th of total reinforcement B. 1/4th of total reinforcement
C. 1/3rd of total reinforcement D. 1/6th of total reinforcement
Ans. C
34. If the initial void ratio is less than critical void ratio for a shear test on cohesionless soil
then the volume of sample
A. Increases B. Decreases
C. Remains Constant D. first decreases then increases
Ans. D
35. At sea level, the value of atmospheric pressure is close to
A. 1.033 m of water column B. 10.33 m of water column
C. 103.3 m of water column D. 101.3 m of water column
Ans. B
36. Defective air circulation in plant’s root zone is an effect of
A. Mixed cropping B. Fall in soil moisture content
C. Water logging D. High temperatures
Ans. C
37. Sulphur dioxide is an air pollutant, which is mainly emitted by
A. Coal burning B. Gasoline fuel
C. Tyres D. Carburettor
Ans. A
38. What will be the max flow in VPH for relation v=55 - 0.44k,where v is speed in kmph and
k isdensity in vpkm
A. 2000 B. 1718
C. 1500 D. 1000
Ans. B
39. Cement used for railway sleepers is designated as
A. 40-S B. 53-S
C. 46-S D. 48-S
Ans. B
6
www.gradeup.co
7
www.gradeup.co
8
www.gradeup.co
A. B.
C. D.
Ans. C
57. Wicket gates are:
A. Gate valve in a penstock B. Sluice gates of dam
C. Runner vanes of reaction turbine D. Guide vanes of reaction turbine
Ans. D
58. Excavation exceeding 1.5 m in width as well as 10 m 2 on plan but not exceeding 30 cm in
depth shall be described as
A. Surface excavation B. Surface dressing
C. Excavation in trenches D. Cutting
Ans. A
59. Design of foundation for a large generator is guided, primarily, by
A. Frequency B. Deformation
C. Strength D. Stiffness
Ans. A
60. Hydraulic jump for energy dissipation is used in:
A. Saft spillway B. Syphon spillway
C. Side channel spillway D. All of these
Ans. B
***
9
www.gradeup.co
10