Professional Documents
Culture Documents
D.Gray code provides cell values that differ in only one bit in adjacent cells.
Answer: D.Gray code provides cell values that differ in only one bit in adjacent cells.
A. 2
B.20
C.200
D.2000
Answer: C.200
4 MOSFET is a
5 Which of the following measuring instruments can measure both AC & DC quantities?
1.PMMC
2.Moving Iron
3.Rectifier Type
4. Induction Type
A. 1 & 2 Only
B. 2 & 3 Only
C. 3 & 4 Only
D. 1 & 4 Only
6 In SCR, the train of Pulse of high frequency for gate triggering is used to reduce………….
C. di/dt problem
8 For a system, starting from rest, the unit-step response of a system is given by
ct=1-e-2t(t≥0)
A.1 / (1+2s)
B.2 / (2+s)
C.1 / (2+s)
D.2s / (1+2s)
9 A 4-pole, 50HZ induction motor have slip, S= 0.5. Then the speed at which motor is running
is:-
A. 750 rpm
B. 1000 rpm
C. 1250 rpm
D. 1500 rpm
10 The damping ratio of a system is found to be zero; then its behaviour will be ___
A. Critically Damped
B. Over Damped
C. Under Damped
D. Oscillatory
Answer: D. Oscillatory
11 Five flip-flops are used to construct a ring counter, then the number of states that ring
counter can have will be
A. 5 states
B.10 states
C.32 states
D. Infinite states
Answer: A. 5 states
12 Which of the following expression is not equal to the unit of Power; i.e watts?
A.Amperes x volts
D.Amperes / volts
Group- II
1. Provides high common mode voltage rejection
2. Has very high input impedance and very high current gain
3. Is a wide band Amplifier
16 For high head hydro-electric plants above 500 meters the type of Turbine used is ___
A.Francis
B.Propeller
C.Pelton
D.Kaplan
Answer: C.Pelton
A.TC ∝ θ
B.TC ∝ Sin θ
C.TC ∝ Sin2 θ
D.TC ∝ (1/θ)
Answer: A.TC ∝ θ
20 The Fermi function for a hole will be…………., (If the Fermi function for an electron is f(E),
where E is the energy.)
A. 1 - f(E)
B. 1 + f(E)
C. 1 / f(E)
D. f(E)
Answer: A. 1 - f(E)
A. In series
B.In parallel
C. Back to back
D. None of these
22 If the frequency of AC input & max. flux in the core of a single phase transformer is
increased by a factor of 4 & 2 respectively, the change in rms value of induced emf in
secondary windings will be
A. Reduced by half
B. Increased By half
C. Increased By 8 times
D. Decreased By 8 times
B.101111
C.111110
D.110001
Answer: B.101111
24 LVDT accelerometers are used for which type of frequency vibration measurements?
A. Low
B. Medium
C. High
D. Very High
Answer: A. Low
25 In case of single line to ground fault (LG), all the sequence currents are equal to :-
A.3 Ia
B.la/3
C.Ia
D.Ia2
Answer: B.la/3
26 In a cascaded amplifiers, impedance matching is done between the output of previous
stage and input of next stage, _____
A. only 1 is correct
B. only 2 is correct
C. only 3 is correct
28 When the length of a wire of resistance R is uniformly stretched to n times its original value,
then the value of its new resistance will be
A. nR
B.R/n
C.n2R
D. R
Answer: C.n2R
30 Which one of the following converter can operate both in 3-pulse and 6-pulse mode?
A.Increases
B.Decreases
A.Only 1 is correct
A. A spike
B.A ramp
D.A pulse
A. FCT
B. GTO
C.MCT
D.IGBT
Answer: D.IGBT
36 Which one of the following is the correct sequence of the blocks (therein) starting from the
input in Analog Data Acquisition System is
A. Kelvin’s bridge
B.Anderson’s bridge
C.Schering bridge
D.Carey-Foster’s bridge
A.5V
B.50V
C.200V
D.0V
Answer: D.0V
D. No filter is required
A.Semiconductor devices
B. Vacuum tubes
C.Only in BJTs
D.Photo devices
Answer: B. Vacuum tubes
44 The max demand of a power at a plant is 500 Mw with a load factor of 0.8. If the plant
capacity is 800 Mw, then plant capacity factor is
A.0.25
B.0.5
C.0.75
D.0.8
Answer: B.0.5
45 For an auto transformer, the ratio of conducted VA to transformed VA is 2; then the value of
K will be
A.2
B.3
C. 2/3
D. 3/2
Answer: C. 2/3
46 Two spheres having radii r1 and r2 are connected by a conducting wire and each sphere is
having charge Q, then
A. Production of voltage
B. Production of current
A.High tolerance
49 Which one of the following force acts against the centrifugal force and keeps the electrons
in their orbits, when the electrons revolve around the nucleus with high speed.
C.Adhesive force
D.None of these
50 Which of the following error is not present in a PMMC type measuring instruments?
A. Frictional error
B. Temperature error
C. Frequency error
D. Hysteresis error
51 In a DC Motor, speed control by varying Armature circuit resistance gives speed ___
D. only below base speed only & above base speed only
Answer: A. below base speed only
52 Which of the following power system Device requires continuous signal for keeping them in
turn-on states?
A. SCR
B. GTO
C. BJT
D.MCT
Answer: C. BJT
55 A full adder circuit can be realized with ………….. Half-adder and a ……….. gate
A.Two, zero
B.Two, NOR
C.Two, OR
D.Two, AND
Answer: C.Two, OR
56 Which one of the following is the correct match of Group-I with Group-II
Group-I (Bridges)
A. Anderson Bridge
B. Kelvin Double bridge
C. Schering Bridge
D. Wein bridge
A.Reciprocity theorem
B.Duality theorem
C.Compensation theorem
D.Equivalence theorem
A.50
B.57.5
C.75
D.66.6
Answer: B.57.5
A. Current
B.Electric field
C.Magnetic field
D.Pressure
A.OR-AND
B. AND-OR
C.NOT-OR
D. AND-NOT
Answer: B. AND-OR
A.Equal to zero
62 Twelve 6 ohms resistor are used as edge to form a cube. The resistance between two
diagonally opposite corner of the cube (in ohms) is
A.5/6
B.6/5
C.5
D.6
Answer: C.5
A. Holes
B. Electrons
C. +ve ions
D.–ve ions
Answer: B. Electrons
C.has no charge
65 Which of the following refrigerant used in air conditioner in Indian have the lowest global
warming potential?
A.R-22
B.R-32
C.R410A
D.R290
Answer: D.R290
A.Propeller type
A.LVDT
B.Thermocouple
C.Pezoelectric
D. Photovoltaic cell
Answer: A.LVDT
A.Degree
B.Steradian
C.Radians
D.Radians/meter
Answer: B.Steradian
74 For silicon PN junction, at 20 degree Celsius, it has a reverse saturation current of 10 pA.
For the same bias, the reverse saturation current at 40 degree Celsius will be
A.20 pA
B.30 pA
C.40 pA
D. 80 pA
Answer: C.40 pA
A. Excess-3 code
B. 8421 code
C. 7421 code
D.Gray code
A. Ultraviolet
B. Infrared
D. Visible region
Answer: B. Infrared
77 Parameters for a RLC circuits are R= 2 ohms, L= 1 Henry, C=1 Farad. If these are
connected in Parallel, then the system response of the circuit will be
A. Un-damped
B.Critically damped
C.Under damped
D.Over damped
Answer: C.Under damped
78 Which one of the following is the correct match of Group-I with Group-II
Group-I
A. Moving iron and hot wire type
B. Galvanometer
C. PMMC
D. Electrostatic type
Group-II
1. Air Friction
2. Electromagnetic
3. Fluid friction
4. Eddy current
A.100
B.90.86
C.70.7
D.80.8
Answer: C.70.7
82 Which of the following power electronics devices are unidirectional current devices?
1. Triac
2. RCT
3. GTO
4. MOSFET
5. IGBT
83 Rotor input to rotor gross output of an induction motor are related to each other as ____
(where S is slip)
A. S
B. 1/(S-1)
C. (S -1)
D. 1/S
84 The total flux emitted by a lamp source of 100 candle power is approximately
A.314
B.628
C.1256
D.2512
Answer: C.1256
A.are parallel
C. are perpendicular
86 The Laplace transform of a signal y(t) is Y(S) = 1 / s(s-1), then its final value will be
A.-1
B.0
C.1
D.Unbounded
Answer: D.Unbounded
87 To sample the signal properly, find the sampling period of the signal for which the frequency
spectrum lies within the band f0 to f1, where f1 is greater than f0 .
88 For a Op-Amp circuit working as high gain comparator, if one input is connected to ground
and a sinusoidal voltage is applied to the other input, then the output of the circuit will be
A.A sinusoid
89
2.36 V
- 2.36 V
4.414 V
- 4.414 V
Answer: - 4.414 V
90 In overhead transmission lines, the use of stock bridge dampers is done to ___
A.Transformer
B.DC machines
C.Energy meters
D.Synchronous machines
93 Which one of the following is used to fed pulse-width modulated inverter for the control of
an ac motor?
A. Ac regulator
B. Uncontrolled rectifier
C.Controlled rectifier
D. Cycloconverter
Group-II
1.Frequency division
2. Addressing in memory chips
3. Serial to parallel data conversion
95 When an SCR is in conducting state and a reverse voltage is applied between anode and
cathode, but it fails to turn off. What is the reason behind it ?
96 For a common collector amplifier, which one of the following characteristics is not correct?
97 For signed decimal numbers represented by 6-bits 1’s compliment number, the range will
be
A. -31 to +31
B. -63 to +63
C. -64 to +63
D. -32 to + 31
98 Which of the following AC Bridge is used for the measurement of mutual inductions
between two coils?
A. Wein Bridge
B. Hay Bridge
D. Schering Bridge
A.Low, high
B.High, low
C. Low, low
D.High, high
100 An underground cable has an impedance of 0.4 mH/km &capacities of 0.16 µf/ km; then the
surge independence of the cable will be
A.0.4
B.2.5
C.sqrt (2.5)
D.0.6
102 The feedback transformer and diode in complementary commutated inverters is used to
Group-II
1. Low frequency oscillator
2. High frequency oscillator
3. Stable frequency oscillator
A.A-1 B-2 C-3
A. Moving plunger
B. Moving Iron
C. Buchholz
D. Balanced beam
Answer: C. Buchholz
106 If the concentration of current is more on the surface in comparison to its core, then the
phenomenon is called as ___
A.Proximity effect
B.Corona
C.Skin effect
D.Ferranti effect
107 Which of the following refrigerants used in air conditioner does not deplete ozone layer?
A.CFCs
B.HFCs
Answer: B.HFCs
108 The temperature of the p-type semiconductor is gradually and continuously increased.
What will be the effect on Fermi level?
D. It will move into the region between the acceptor level and the valence band.
109 Freewheeling diode is used with bridge type ac/dc converter to……….
C.Regenerative breaking
110 The average demand of a thermal plant is 500 MW and its systems capacity is 1000 MW,
then Plant Capacity Factor (PCF) is :-
A.0.5
B.2
C.1
D.0
Answer: A.0.5
111 Which of the following AC Bridges is used for the measurement of low (Q<1) quality factors
of inductance?
B. Hay Bridge
C. Anderson Bridge
IDSS = 1 mA
and VP= - 5 V
A.0.2 mS
B.0.4 mS
C.0.6 mS
D.0.8 mS
Answer: B.0.4 mS
113 The power plant which is cheapest in operation & maintenance is
A.2
B.4
C.8
D.16
Answer: C.8
115
116 In power factor correction of a 3φ system, the capacitance required per phase in star
connection is equal to ……….. times the capacitance required per phase in delta
connection.
A.SQRT (2)
B.2
C.SQRT (3)
D.3
Answer: D.3
A. cosφ = (R/Z)
B. tanφ=(R/X)
C. cosφ = (X/R)
D. tanφ= (R/Z)
119 According to energy conservation ACT 2001, The Bureau of energy efficiency (BEE) came
into force from :-
A. 2000 AD
B. 2001 AD
C. 2002 AD
D. 2003 AD
Answer: C. 2002 AD
121 In case of a fault in a transmission line, which device sends information and to which device
to interrupt the circuit respectively?
A.Relay, fuse
122 Which one of the following represents the line integral of the vector potential A around the
boundary of a source S?
D.Current density
123 Which one of the following transistor configuration provides the highest output impedance
A.Common Base
B.Common collector
C.Common Emitter
400+j300
400-j300
j100
- j900
Answer: 400-j300
125 The condition at which the drain current becomes nearly constant, then the drain-source-
voltage at this condition is known as
A. Breakdown voltage
B. Barrier voltage
D. Pick-off voltage
126 Which one of the following statement is correct for AND logic gate?
127 The function of dampers bars in salient pole synchronous machines is/are:
C. Both Damp out the rotor oscillations & to start the machine
Answer: C. Both Damp out the rotor oscillations & to start the machine
129 If a damper bar 3φ synchronous motors’ load is increased beyond limit, it will
C.will stop
130 The depth of penetration of a wave in lossy dielectric increases with increasing
A.Conductivity
B.Permeability
C.Wavelength
D.Permittivity
Answer: C.Wavelength
131 Which one of the following materials does not contain a covalent bond?
A.Metal
B.Silicon
C.Organic polymers
D.Diamond
Answer: A.Metal
B.The same transformer can be used from either sides; HV/LV sides or LV / HV sides
A. 450 ± 6 Ω
B. 450 ± 4 Ω
C. 450 ± 2 Ω
D. 450 ± 12 Ω
Answer: D. 450 ± 12 Ω
135
11.86
10
25
11.18
Answer: 11.18
136 For a closed surface, the value of total electric flux coming out through it will be equal to
……..
A.Zero
138 Which one of the following conversion is done by Power chopper circuit ?
A.dc to dc
B. ac to ac
C. ac to dc
D. dc to ac
Answer: A.dc to dc
139 For a logic gate, when all its inputs are at logic ‘0’, the output is ‘1’
The logic gate is either
B.Reverse saturation current of a silicon diode is much smaller than that of a germanium.
C. The reverse resistance of a junction diode increases with increase with temperature
D.Reverse saturation current in a BJT approximately doubles for every 10 degree Celsius
rise in temperature.
Answer: C. The reverse resistance of a junction diode increases with increase with temperature
141 Find the correct match of Group-I with Group-II
Group-I (Type of device)
A. Zener diode
B. Tunnel diode
C. Schottky diode
D. Photodiode
142 The steam generated in case of a water tube boiler as compared to fire tube boiler is
A.Less
B.More
C.Equal
Answer: B.More
A.(-0.5, 0)
B.(-2.548, 0)
C. (-4, 0)
D.(-0.784, 0)
Answer: D.(-0.784, 0)
144 Which of the following materials is used as both cladding & moderator in a nuclear power
plant?
A.Magnesium
B.Zirconium
C.Beryllium
D.Graphite
146 Which of the following have the maximum specific ratio (ratio of discharge pressure to
section pressure)
A.Fan
B.Blower
D.Compressor
Answer: D.Compressor
147 Four thyristors of rating 800V are connected in series. Then the percentage series derating
factor, if the power circuit is of 3KV, will be ____ percent.
A.12.5
B.6.25
C.25
D.50
Answer: B.6.25
148 The insulation resistance of a 10km underground cable is 1MΩ. Then the insulation
resistance of same cable of length 100km will be
A.1MΩ
B.10MΩ
C.100MΩ
D.0.1MΩ
Answer: D.0.1MΩ
149 Per unit impedance of a generator of 100MVA, 10 KV is 0.2PU; then the impedance of
same in ohms will be
A. 0.5 Ω
B. 0.2 Ω
C. 5 Ω
D. 2 Ω
Answer: B. 0.2 Ω