Professional Documents
Culture Documents
09mar2011111237 Servi
09mar2011111237 Servi
Production Effective :
VIN Production Date
NA From January, 2005
(3) Register the ECM COMMUNICATION ID between the new transponder key ECU and the
ECM.
Target ECU Procedure
ECM "D"
(2) Register the ECM COMMUNICATION ID between the new transponder key ECU and the
ECM.
Target ECU Procedure
ECM "D"
HINT:
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
• If the key code registration has failed in automatic key code registration mode, code 2-1
will be indicated by the security indicator. Trying to re-register an already registered key
will cause code 2-2 to be output when the key is inserted. If the number of registered
key codes exceeds the maximum limit, code 2-3 will be indicated by the security
indicator. The details are shown in the next step.
(2) Automatic Key Code Registration (New Registration) by using the switch operation.
Procedure Time Security Indicator Condition
1. Start Blinking
(a) Driver door is closed. - HINT:
(b) Key is not inserted in ignition key cylinder. Until the first key is inserted.
7. Next OFF
8. End
HINT:
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
• If the key code registration has failed in automatic key code registration mode, code 2-1
will be indicated by the security indicator. Trying to re-register an already registered key
will cause code 2-2 to be output when the key is inserted. If the number of registered
key codes exceeds the maximum limit, code 2-3 will be indicated by the security
indicator. The details are shown in the next step.
(3) End automatic key code registration mode.
Automatic key code registration mode can be forced to end with it when at least 1 key
code (immobiliser code) for the master key has been registered.
HINT:
• In automatic key code registration mode, when no key is inserted into the ignition key
cylinder, the security indicator remains on.
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
• If the key code registration has failed in automatic key code registration mode, code 2-1
will be indicated by the security indicator. Trying to re-register an already registered key
will cause code 2-2 to be output when the key is inserted. If the number of registered
key codes exceeds the maximum limit, code 2-3 will be indicated by the security
indicator. The details are shown in the next step.
0.2 sec.
ON
Normal (Immobiliser
system is operating OFF
normally)
1.8 sec.
ON
Code 2 - 1
OFF
0.25 sec.
0.5 sec.
ON
Code 2 - 2 OFF
0.25 sec.
0.5 sec.
ON
Code 2 - 3
OFF
0.25 sec.
0.5 sec.
B111593E11
HINT:
Automatic key code registration mode can be forced to end when the key codes
(immobiliser codes) for 1 or more master keys have been registered.
7. Next OFF
8. End
HINT:
• A brief outline of procedures for key code registration is shown on this page. Refer to
the intelligent tester screen instructions for more information.
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
• If the key code registration has failed in automatic key code registration mode, code 2-1
will be indicated by the security indicator. Trying to re-register an already registered key
will cause code 2-2 to be output when the key is inserted. If the number of registered
key codes exceeds the maximum limit, code 2-3 will be indicated by the security
indicator. The details are shown in the next step.
7. Next OFF
8. End
HINT:
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
• If the key code registration has failed in automatic key code registration mode, code 2-1
will be indicated by the security indicator. Trying to re-register an already registered key
will cause code 2-2 to be output when the key is inserted. If the number of registered
key codes exceeds the maximum limit, code 2-3 will be indicated by the security
indicator. The details are shown in the next step.
4. ERASURE OF KEY CODE: PROCEDURE "C"
(a) Erasing Key Codes
HINT:
• All key codes are erased except for the master key, which is used for erasing the key codes.
In order to use a key whose code has been erased, a new key code must be registered.
• Registration will be cancelled if each step is not completed within the specified time.
(1) Erase key codes using the intelligent tester.
Procedure Time Security Indicator Condition
Blinking
1. Start HINT:
Until the first key is inserted.
-
2. Insert an already registered master key into
the ignition key cylinder and turn the ignition OFF
switch on.
3. Intelligent tester operation:
(a) Select Body from the menu.
(b) Select Immobiliser.
(c) Select Utility.
(d) Select Transponder Code Erasure. Within 120 sec. OFF
HINT:
After the above operation, proceed to the next
step in accordance with the prompts on the
tester screen.
Within 10 sec.
4. Remove the master key. HINT: ON for 1 sec., then OFF
After the tester instruction.
5. Next - Blinking
6. End
HINT:
• A brief outline of procedures for key code registration is shown on this page. Refer to
the intelligent tester screen's instructions for more information.
• When the immobiliser system is operating normally and the key is pulled out, the
security indicator blinks continuously.
(2) Erase key codes by switch operation.
Procedure Time Security Indicator Condition
Blinking
1. Start - HINT:
Until the first key is inserted.
2. Insert an already registered master key into
the ignition key cylinder and remove the
master key 6 times. Within 35 sec. OFF
HINT:
When the immobiliser system is operating normally and the key is pulled out, the security
indicator blinks continuously.
5. ECU COMMUNICATION ID REGISTRATION (TRANSPONDER KEY ECU): PROCEDURE "D"
(a) Register the ECU Communication ID
NOTICE:
• The ECU COMMUNICATION ID must be registered when the transponder key ECU is
replaced in order to match these ECM COMMUNICATION IDs.
• The engine cannot be started unless the ECM COMMUNICATION IDs match.
(1) Register the ECU Communication ID operation.
CG
DLC3
TC
SST
B128293E01
Hold the key with its ornament surface within a range of 10 mm (0.39 in.) or less from the engine switch.
B113988E01
*1: Repeat this process for each key which is to be registered for the vehicle. Finish the
procedure for each key within 30 seconds. If the procedure for any of the keys has not been
finished within the specified time, perform the registration procedures again from process 1.
Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more keys
are in the cabin simultaneously, electric waves will interfere with each other, preventing normal
registration.
(b) PROCEDURE "B"
New key ID registration (If replacing the certification ECU, perform the following.)
Process Procedure
Turn the engine switch on (IG). Connect the intelligent tester. Select
(Entry & Start) → (Utility) → (Key Code Registration) from the tester
menu.
HINT:
1. Start of registration
The engine switch cannot be turned on (IG) more than 10 times. After
connecting the tester, turn the tester on while turning the driver's door
courtesy switch on and off repeatedly at 1.5 second intervals or less to
continue key registration procedure.
Perform the operation according to the prompts on the intelligent
2. Confirmation of ECU code tester screen. HINT: The mode is automatically selected by the tester,
new registration mode or additional registration mode.
Hold a registered key close to the engine switch. (For details, refer to
3. Confirmation of all registered keys (*1) PROCEDURE "1".)
Confirm that the wireless door lock buzzer sounds.
Perform the operation according to the prompts on the intelligent
4. Confirmation of ECU code
tester screen.
Hold an unregistered key close to the engine switch. (For details, refer
to PROCEDURE "1".)
5. Verification of unregistered key (*2) Confirm that the wireless door lock buzzer sounds. Place the
unregistered key on the front passenger's seat.
Confirm that the wireless door lock buzzer sounds once.
Process Procedure
Perform the operation according to the prompts on the intelligent
6. Registration of ID code
tester screen.
7. End of registration Finish the new key ID registration.
• *1: Repeat this process for each key registered for the vehicle. Finish the procedure for each
key within 30 seconds. If the procedure for any of the keys has not been finished within the
specified time, perform the registration procedures again from process 1. If the key
confirmation procedure for a key is performed, the security indicator comes on and remains
on until all the keys are confirmed.
• *2: Repeat this process for each key which is to be registered for the vehicle. Finish the
procedure for each key within 30 seconds. If the procedure for any of the keys has not been
finished within the specified time, perform the registration procedures again from process 1.
Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more
keys are in the cabin simultaneously, electric waves will interfere with each other, preventing
normal registration.
(c) PROCEDURE "C"
Additional key ID registration
Process Procedure
Turn the engine switch on (IG). Connect the intelligent tester. Select
1. Start of registration (Entry & Start) → (Utility) → (Key Code Registration) from the tester
menu.
Perform the operation according to the prompts on the intelligent
tester screen.
HINT:
The mode is automatically selected by the tester, new registration
2. Confirmation of registered key (*1) mode or additional registration mode.
Hold a registered key close to the engine switch. (For details, refer to
PROCEDURE "1".)
Confirm that the wireless door lock buzzer sounds once.
Perform the operation according to the prompts on the intelligent
3. Confirmation of ECU code
tester screen.
Hold an unregistered key close to the engine switch. (For details, refer
to PROCEDURE "1".)
4. Verification of unregistered key (*2) Confirm that the wireless door lock buzzer sounds once. Place the
unregistered key on the front passenger's seat.
Confirm that the wireless door lock buzzer sounds once.
Perform the operation according to the prompts on the intelligent
5. Registration of ID code
tester screen.
6. End of registration Finish the additional key ID registration.
• *1: Perform this process for one of the keys registered for the vehicle. Finish the procedure
within 30 seconds. If the procedure has not been finished within the specified time, perform
the registration procedures again from process 1.
• *2: Repeat this process for each key which is to be registered for the vehicle. Finish the
procedure for each key within 30 seconds. If the procedure for any of the keys has not been
finished within the specified time, perform registration procedures again from process 1.
Make sure that only 1 key is in the cabin during the registration procedures. If 2 or more
keys are in the cabin simultaneously, electric waves will interfere with each other, preventing
normal registration.
(d) PROCEDURE "D"
Key ID erasure
HINT:
Erase all the registered key codes except one.
Process Procedure
Turn the engine switch on (IG). Connect the intelligent tester. Select
1. Start of code erasure
(Entry & Start) → (Utility) → (Key Code Erasure) from the tester menu.
Perform the operation according to the prompts on the intelligent
tester screen.
2. Confirmation of registered key (Select the key to be registered in
Hold a registered key close to the engine switch. (For details, refer to
the vehicle.)
PROCEDURE "1".)
Confirm that the wireless door lock buzzer sounds once.
Perform the operation according to the prompts on the intelligent
3. Erasure of ID code
tester screen.
4. End of code erasure Finish the key ID erasure.
*1: Perform this process for one of the keys registered for the vehicle. Finish the procedure
within 30 seconds. If the procedure has not been finished within the specified time, perform the
erasure procedures again from process 1.
(e) PROCEDURE "E"
ECU code registration
Process Procedure
Turn the engine switch on (IG). Connect the intelligent tester. Select
1. Start of registration (Entry & Start) → (Utility) → (ECU Communication ID Registration) →
(ID Code Box and Steering Lock) from the tester menu.
Hold a registered key close to the engine switch. (For details, refer to
2. Confirmation of registered key (*1) PROCEDURE "1".)
Confirm that the wireless door lock buzzer sounds once.
Perform the operation according to the prompts on the intelligent
3. Registration of ECU code
tester screen.
4. End of registration Finish the ECU code registration.
*1: Perform this process for one of the keys registered for the vehicle. Finish the procedure
within 30 seconds. If the procedure has not been finished within the specified time, perform the
registration procedures again from process 1.
(f) PROCEDURE "F"
ECU communication ID registration
NOTICE:
• The ECU COMMUNICATION ID must be registered when the transponder key ECU is
replaced in order to match these ECM COMMUNICATION IDs.
• The engine cannot be started unless the ECM COMMUNICATION IDs match.
(1) Register the ECU Communication ID operation.
CG
DLC3
TC
SST
B128293E01