Professional Documents
Culture Documents
Product Specification
SPECIFICATION
FOR
APPROVAL
( ) Preliminary Specification
( ● ) Final Specification
SIGNATURE SIGNATURE
APPROVED BY APPROVED BY
DATE DATE
REVIEWED BY
PREPARED BY
Ver. 1.0 0 / 36
LC430DUY
Product Specification
CONTENTS
Ver. 1.0 1 / 36
LC430DUY
Product Specification
RECORD OF REVISIONS
Ver. 1.0 2 / 36
LC430DUY
Product Specification
1. General Description
The LC430DUY is a Color Active Matrix Liquid Crystal Display with an integral the Source PCB and Gat
e implanted on Panel (GIP). The matrix employs a-Si Thin Film Transistor as the active element.
It is a transmissive type display operating in the normally black mode. It has a 43.0 inch diagonally me
asured active display area with WUXGA resolution (1080 vertical by 1920 horizontal pixel array).
Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes.
Gray scale or the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each
d o t .
Therefore, it can present a palette of more than 16.7M(true) colors.
It is intended to support LCD TV, PCTV where high brightness, super wide viewing angle, high color g
a m u t ,
high color depth and fast response time are important.
LVDS EPI(RGB)
EEPROM
2Port Source Driver Circuit
General Features
Active Screen Size 42.51 inches(1,079.75 mm) diagonal
Source D-IC : 8-bit EPI, gamma reference voltage, and control signals
Drive IC Data Interface
Gate D-IC : Gate In Panel
Viewing Angle (CR>10) Viewing angle free ( R/L 178 (Min.), U/D 178 (Min.))
Weight 1.5 (TBD)Kg (Typ.)
Display Mode Transmissive mode, Normally black
Surface Treatment (Top) Hard coating(3H), Anti-glare treatment of the front polarizer, Haze 1%(Typ.)
Ver. 1.0 3 / 36
LC430DUY
Product Specification
Value
Parameter Symbol Unit Note
Min Max
50 Storage
Humidity [(%)R
Wet Bulb
Temperature [°C]
40
40%
Operation
30
H]
20
10
0
10%
5%
-20 0 10 20 30 40 50 60 70 80
Ver. 1.0 4 / 36
LC430DUY
Product Specification
3. Electrical Specifications
3-1. Electrical Characteristics
Value
Parameter Symbol Unit Note
Min Typ Max
Circuit :
- 350 455 mA 1
Power Input Current ILCD
- 550 715 mA 2
T-CON Option Input High Voltage VIH 2.7 - 3.6 VDC
Selection Voltage Input Low Voltage VIL 0 - 0.7 VDC
Power Consumption PLCD - 4.2 5.5 Watt 1
Note 1. The specified current and power consumption are under the VLCD=12.0V, Ta=25 2°C, fV=60Hz
condition, and mosaic pattern(8 x 6) is displayed and fV is the frame frequency.
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power input is 0.5ms (min.).
4. Ripple voltage level is recommended under ±5% of typical voltage
Mosaic Pattern(8 x 6)
Ver. 1.0 5 / 36
LC430DUY
Product Specification
Note 1. All GND(ground) pins should be connected together to the LCD module’s metal frame.
2. All VLCD (power input) pins should be connected together.
3. All Input levels of LVDS signals are based on the EIA 644 Standard.
4. #1~#6 & #8~#9 NC (No Connection): These pins are used only for LGD (Do not connect)
5. LVDS pin (pin No. #24,25,40,41) are used for 10Bit(D) of the LCD module.
If used for 8Bit(R), these pins are no connection.
6. Specific pin No. #44 is used for “No signal detection” of system signal interface.
It should be GND for NSB(No Signal Black) during the system interface signal is not.
If this pin is “H”, LCD Module displays AGP(Auto Generation Pattern).
Ver. 1.0 6 / 36
LC430DUY
Product Specification
Display
tHV 960 960 960 tCLK 1920 / 2
Period
Horizontal
Blank tHB 100 140 240 tCLK 1
Total tHP 1060 1100 1200 tCLK
Display
tVV 1080 1080 1080 Lines
Period
Frequency
Vertical fV 47 60 63 Hz 2
notes: 1. The input of HSYNC & VSYNC signal does not have an effect on normal operation (DE Only Mo
de).
If you use spread spectrum of EMI, add some additional clock to minimum value for clock margi
n.
2. The performance of the electro-optical characteristics may be influenced by variance of the verti
cal
refresh rate and the horizontal frequency
3. Spread Spectrum Rate (SSR) for 50KHz ~ 100kHz Modulation Frequency(FMOD) is calculated by
(7 – 0.06*Fmod), where Modulation Frequency (FMOD) unit is KHz.
LVDS Receiver Spread spectrum Clock is defined as below figure
Ver. 1.0 7 / 36
LC430DUY
Product Specification
※ Please pay attention to the followings when you set Spread Spectrum Rate(SSR) and Modulation Frequency
(FMOD)
1. Please set proper Spread Spectrum Rate(SSR) and Modulation Frequency (FMOD) of TV system LVDS outp
ut.
2. Please check FOS after you set Spread Spectrum Rate(SSR) and Modulation Frequency(FMOD) to avoid
abnormal display. Especially, harmonic noise can appear when you use Spread Spectrum under FMOD 30
KHz.
Ver. 1.0 8 / 36
LC430DUY
Product Specification
0.7VDD
DE, Data
0.3VDD
tCLK
0.5 VDD
DCLK
Valid data
First data Invalid data Pixel 0,0 Pixel 2,0 Invalid data
Valid data
Second data Invalid data Pixel 1,0 Pixel 3,0 Invalid data
DE(Data Enable)
tHV
tHP
1 1080
DE(Data Enable)
tVV
tVP
Ver. 1.0 9 / 36
LC430DUY
Product Specification
LVDS +
V CM V IN _ MAX V IN _ MIN
LVDS Clock
LVDS Data
( F clk = 1 /T clk )
tSKEW tSKEW
Tclk
LVDS 1’st Clock
tSKEW_min tSKEW_max
Ver. 1.0 10 / 36
LC430DUY
Product Specification
0.5tu tui
i
LVDS Data
360ps
VTH
0V
(Differential) VTL
360ps
teff
0V
(Differential)
Ver. 1.0 11 / 36
LC430DUY
Product Specification
Logic & EPI Power Voltage VCC - 1.62 1.8 1.98 VDC
EPI input common voltage VCM LVDS Type 0.8 VCC/2 1.3 V
EPI +
Vdiff Vdiff
0V
EPI -
Vdiff
Vcm
0V
(Differential Probe) (Active Probe)
0.5 UI
Veye
0V
Veye
(Differential Probe)
B1 B2
Ver. 1.0 12 / 36
LC430DUY
Product Specification
The brightness of each primary color(red,green,blue) is based on the 8bit gray scale data input for the c
olor.
The higher binary input, the brighter the color. Table 6 provides a reference for color versus data input.
Table 6. COLOR DATA REFERENCE
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
RED (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED (255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN (254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN (255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE (000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE (001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE (254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE (255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Ver. 1.0 13 / 36
LC430DUY
Product Specification
90% 90%
Power Supply For LCD
VLCD 10% 10% 10%
0V
T7
T1
T5
T2
Valid Data Vcm : LVDS Common mode Voltage
30%
Interface Signal (Tx_clock) 0V
100% T3 T4
T6
User Control Signal
(LVDS_select)
Value
Parameter Unit Notes
Min Typ Max
T1 0.5 - 20 ms 1
T2 0 - - ms 2
T3 400 - - ms 3
T4 100 - - ms 3
T5 1.0 - - s 4
T6 0 - T2 ms 5
T7 0 - - ms 6
1. Even though T1 is over the specified value, there is no problem if I2T spec of fuse is satisfied.
Note : 2. If T2 is satisfied with specification after removing LVDS Cable, there is no problem.
3. The T3 / T4 is recommended value, the case when failed to meet a minimum specification,
abnormal display would be shown. There is no reliability problem.
4. T5 should be measured after the Module has been fully discharged between power off and on period.
5. If the on time of signals (Interface signal and user control signals) precedes the on time of Power (VLCD),
it will be happened abnormal display. When T6 is NC status, T6 doesn’t need to be measured.
6. It is recommendation specification that T7 has to be 0ms as a minimum value.
※ Please avoid floating state of interface signal at invalid period.
※ When the power supply for LCD (VLCD) is off, be sure to pull down the valid and invalid data to 0V.
Ver. 1.0 14 / 36
LC430DUY
Product Specification
4. Optical Specification
Optical characteristics are determined after the unit has been ‘ON’ and stable in a dark environment at
25±2°C. The values are specified at 50cm from the LCD surface at a viewing angle of and equal to 0
°.
FIG. 1 shows additional information concerning the measurement equipment and method.
50cm
FIG. 1 Optical Characteristic Measurement Equipment and Method
Value
Parameter Symbol Unit notes
Min Typ Max
Rx 0.661
RED
Ry 0.328
Bx 0.134
BLUE
By 0.122
right(=0°) r (x axis) 89 - - -
Viewing
2D left (=180°) l (x axis) 89 - - -
Angle
(CR>10)
up (=90°) u (y axis) 89 - - -
down (=270°) d (y axis) 89 - - -
Gray Scale - - - 4
Ver. 1.0 15 / 36
LC430DUY
Product Specification
2. Response time is the time required for the display to transit from any gray to white (Rise Time,
TrR)
and from any gray to black (Decay time, TrD). For additional information see the FIG. 3.
※ G to GBW Spec stands for average value of all measured points.
Photo Detector : RD-80S / Field : 2 °
3. G to G σ is Variation of Gray to Gray response time composing a picture
Xi = Individual Data
G to G (σ) = √ Σ(Xi- u)2
N
u = Data average
N : The number of Data
4. The value of transmittance should be extracted using the standard light source of D65
5. The value of color coordinates should be extracted using the standard light source of D65
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axi
s w h i c h
is normal to the LCD module surface. For more information, see the FIG. 4.
7. Gray scale specification
Gamma Value is approximately 2.2. For more information, see the Table 9.
Table 9. GRAY SCALE SPECIFICATION
L0 0.07
L15 0.27
L31 1.04
L47 2.49
L63 4.68
L79 7.66
L95 11.5
L111 16.1
L127 21.6
L143 28.1
L159 35.4
L175 43.7
L191 53.0
L207 63.2
L223 74.5
L239 86.7
L255 100
Ver. 1.0 16 / 36
LC430DUY
Product Specification
H
A
② ③
①
V
B
A : H / 4 mm
④ ⑤ B : V / 4 mm
@ H,V : Active Area
Response time is defined as the following figure and shall be measured by switching the input signal
for “Gray(N)” and “Black or White”.
Tr Tf
100
90
Optical
Response
10
Gray(N) White Gray(N) Black
0
N = 0(Black)~255(White)
Ver. 1.0 17 / 36
LC430DUY
Product Specification
Normal
E Y
= 90 , Up
= 180 , Left
= 0 , Right
= 270 , Down
Ver. 1.0 18 / 36
LC430DUY
Product Specification
5. Mechanical Characteristics
Item Value
Horizontal 953.0mm
Outline Dimension
Vertical 543.0mm
(Only Glass)
Thickness 1.4 mm
Horizontal 941.184mm
Active Display Area
Vertical 529.416mm
Hard coating(3H)
Surface Treatment
Anti-glare treatment of the front polarizer : Haze 1%(Typ.)
Note : Please refer to a mechanical drawing in terms of tolerance at the next page.
Ver. 1.0 19 / 36
LC430DUY
Product Specification
6. Mechanical Dimension
6-1. Board Assembly Dimension
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
B B
C C
D D
E E
F F
G G
H H
i i
J J
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 <A1>
Date Version
Ver. 1.0 20 / 36
LC430DUY
Product Specification
Date Version
Ver. 1.0 21 / 36
LC430DUY
Product Specification
7. Reliability
Table 11. ENVIRONMENT TEST CONDITION
Note : Before and after Reliability test, LCM should be operated with normal function.
Ver. 1.0 22 / 36
LC430DUY
Product Specification
8. International Standards
8-1. Safety
a) UL 60065, Underwriters Laboratories Inc.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
b) CAN/CSA C22.2 No.60065:03, Canadian Standards Association.
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
c) IEC 60065, The International Electrotechnical Commission (IEC).
Audio, Video and Similar Electronic Apparatus - Safety Requirements.
8-2. Environment
a) RoHS, Directive 2011/65/EU of the European Parliament and of the council of 8 June 2011
Ver. 1.0 23 / 36
LC430DUY
Product Specification
9. Packing
Ver. 1.0 24 / 36
LC430DUY
Product Specification
10. Precautions
Please pay attention to the followings when you use this TFT LCD module.
Ver. 1.0 25 / 36
LC430DUY
Product Specification
(1) Temperature : 5 ~ 40 ℃
(2) Humidity : 35 ~ 75 %RH
(3) Period : 6 months
(4) Control of ventilation and temperature is necessary.
(5) Please make sure to protect the product from strong light exposure, water or moisture. Be careful f
or
condensation.
(6) Please keep the modules at a circumstance shown below Fig. 2
Ver. 1.0 26 / 36
LC430DUY
Product Specification
# APPENDIX-I-1
■ Pallet Ass’y ⓑ
① ②
ⓐ
③
ⓒ ④
ⓓ
⑤
ⓔ
ⓐ Pallet Plywood
ⓒ PE Sheet PE
ⓗ
⑥ ⓓ Top Packing EPS
Bottom Packi
ⓔ EPS
ng
ⓕ ⓕ Angle Packing Single Wall
ⓖ
ⓖ Tape OPP
Ⓙ ⓗ Band PP
ⓘ Clip Steel
ⓕ Ⓙ Wrap L-LDPE
Ver. 1.0 27 / 36
LC430DUY
Product Specification
# APPENDIX-I-2
■ Control PCB Packing Ass’y
[8Tray+Empty Tray]
[10pcs/Tray]
NO
DESCRIPTION MATERIAL
.
2 Tray PET
3 Box SWR4
Ver. 1.0 28 / 36
LC430DUY
Product Specification
# APPENDIX- II-1
■ Serial Label
20±0.2mm
MADE IN KOREA
6±0.2mm
Ver. 1.0 29 / 36
LC430DUY
Product Specification
# APPENDIX- II-2
■ BOX Label
LC430DUY-SHA1
QTY : 17
■ Pallet Label
LC430DUY
SHA1
136 PCS 001/01-01
MADE IN KOREA RoHS Verified
XXXXXXXXXXXXX XXX
Ver. 1.0 30 / 36
LC430DUY
Product Specification
# APPENDIX- III-1
■ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7= “L” or “NC”)
Vsync 57
Data Enable 58
CLOCK 12
Note: 1. The LCD module uses a 100 Ohm[Ω] resistor between positive and negative lines of each rec
eiver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data. 31 / 36
Ver. 1.0
LC430DUY
Product Specification
# APPENDIX- III-2
■ Required signal assignment for Flat Link (Thine : THC63LVD103) Transmitter(Pin7= “H” )
Vsync 57
Data Enable 58
CLOCK 12
Note :1. The LCD module uses a 100 Ohm[Ω] resistor between positive and negative lines of each rece
iver
input.
2. Refer to LVDS Transmitter Data Sheet for detail descriptions. (THC63LVD103 or Compatible)
3. ‘7’ means MSB and ‘0’ means LSB at R,G,B pixel data. 32 / 36
Ver. 1.0
LC430DUY
Product Specification
# APPENDIX- IV
■ LVDS Data-Mapping Information (8 Bit )
RCLKP
RCLKM
RAP R13’ R12’ G12 R17 R16 R15 R14 R13 R12 G12”
RBP G14’ G13’ B13 B12 G17 G16 G15 G14 G13 B13”
RCP B15’ B14’ DE VSYNC HSYNC B17 B16 B15 B14 DE”
RCLKP
RCLKM
RAP R11’ R10’ G10 R15 R14 R13 R12 R11 R10 G10”
RBP G12’ G11’ B11 B10 G15 G14 G13 G12 G11 B15”
RCP B13’ B12’ DE VSYNC HSYNC B15 B14 B13 B12 DE”
Ver. 1.0 33 / 36
LC430DUY
Product Specification
# APPENDIX- V
■ Option Pin Circuit Block Diagram
1KΩ
LVDS Select
(Pin 7) LVDS Select
60kΩ
ASIC
(TCON)
Ver. 1.0 34 / 36
LC430DUY
Product Specification
# APPENDIX-Ⅶ-1
■ Flicker Adjustment
Parameter Unit Min Typ Max Note
Adjust Pattern /
- G H2Dot Full Flicker / 127Gray 60Hz
Gray Level
Position - Center
R G B R G B R G B R G B R G B
Row 1
Row 2 127Gray
Row 3
0Gray
Row 4
SCL
PMIC
SDA
B A : Pull-up Resistors
(If it is necessary)
Adjustment JIG LCD Module B : I2C Connector
(Refer to Appendix IX)
Ver. 1.0 35 / 36
LC430DUY
Product Specification
# APPENDIX-IX
-LCD Connector : TF06L-50S-0.5SH (Manufactured by HRS) or Compatible
- Material List
◈ Note
- Pad : GOLD Plating
- # ≥ Cpk 1.0
- ## ≥ Cpk 1.33
- Stiffener color : Sky Blue
- H-F
- Dimensions unit : mm
Ver. 1.0 36 / 36