Professional Documents
Culture Documents
Rev. 12/09
COPING DIAGRAMS
MEMBRANE/ #9 x 1-1/2" SS
1-1/2" SS RING
WALL SCREW w/ NEOPRENE ROOF
SHANK NAIL
WASHER, TYP. of (4) SIDE
WALL
6" to less than 20"
1-1/2" SS RING (Anchor Clip Design) ROOFING
SHANK NAIL MEMBRANE
FOR FACE >6"
ANCHOR CLIP
NAIL THROUGH
ANCHOR CLIP
ON FACE >6"
*3/4"
*3/8"
ROOF
SIDE
WALL
20" or Greater
(Anchor Clip Design)
Rev. 12/09
STRAIGHT PARAPET INSTALLATION
A
(4) SCREWS DO NOT USE SEALANT
PER CLIP TOP
AT JOINT SPLICES
E
B
(1) NAIL PER INSIDE
CORNER SUPPORT TOP
C F
F D
(2) LOWER NAILS PER CLIP
FACE IF FACE IS >6" & (2)
PER JOINT SPLICE FACE
F
(2) NAILS PER OUTSIDE
D CORNER SUPPORT FACE
Rev. 12/09
HOOK FRONT
SNAP BACK
ROOF
ROOF SIDE
SIDE
SCREW OR RIVET
TOP VIEW (BY INSTALLER) SEALANT BY
L
INSTALLER
END TERM
END
L
CAP
L=23 1/4" - for wall widths 16" wide
L=29 1/4" - for wall widths > 16" and 23" wide
L=custom for wall widths > 23" wide
WALL
STEP 1: Installing Anchor Clips at Corners & Along the Parapet END CLIP NOT
Locate anchor clips as shown. Pull clips snugly against the outside SHOWN
face. Place four (4) screw fasteners in the top of the clip with
STEP 5: Installing End Caps and End Terms
Install end caps and end terms by hooking face and snapping back
fasteners centered in slotted holes. Place two (2) ss ring shank nails
into place. End caps must be restrained from moving by securing the
in the clip face if face is >6". Position the joint splice over the center
end cap to the clip using a stainless steel screw or rivet (by installer)
of the clip and install as shown using two (2) ss ring shank nails thru
through the roof side leg of the end cap. End terms should be
aligning holes. Joint splices should be installed at ALL clip locations.
restrained similarly if no fasteners are previously installed in the end
term wall flange.
COPING
STRAIGHT
LENGTH
WALL
END
COPING
STEP 2: Installing Anchor Clips at Wall Ends MITER
Install the first anchor clip approximately 2" from the wall end as
shown. Install the second anchor clip 24" on center from the wall
end. (If end cap leg is other than 24" adjust clip accordingly.)
ROOF
ROOF
SIDE
SIDE
3" 3" HOOK FRONT
SNAP BACK
STEP 6: Installing Coping Straight Lengths
Begin installing from the corners and ends working inward to the
3" 3" center. Allow a 1/4" gap between the coping sections for
thermal expansion. Lengths of all straight pieces should be
considered prior to cutting to avoid creating relatively short sections
OUTSIDE CORNER INSIDE CORNER
of cap adjacent to full length sections. There should be an anchor clip
STEP 3: Installing Corner Support Clips and joint splice at least every 60" O.C. (40" O.C. when wall is 17"-32"
Two (2) corner support clips are to be placed at all corners to wide) and at every joint. Every fifth 10-foot section of coping should
support the cap. Secure clips using 1-1/2" ss ring shank nails. Set be secured to the clip using a single stainless steel screw or rivet
each clip away from the corner approximately 3". (same procedure as STEP 5) to isolate movement within a
containment zone.
Rev. 12/09
RADIUS PARAPET INSTALLATION
A
(4) SCREWS
DO NOT USE SEALANT
PER CLIP TOP AT JOINT SPLICES
E
C F
F D
(2) NAILS PER CLIP FACE
IF FACE IS >6" & (2)
PER JOINT SPLICE FACE
F
(2) NAILS PER
D OUTSIDE CORNER
SUPPORT FACE
OUTSIDE CORNER INSIDE CORNER
RADIUS TO STRAIGHT RADIUS TO STRAIGHT
Rev. 12/09
HOOK FRONT
SNAP BACK
ROOF SIDE
ROOF
SIDE
SEALANT BY
RO
DE
WALL
END
RADIUS TO
STRAIGHT
MITER
STEP 2: Installing Anchor Clips at Wall Ends
Install the first anchor clip approximately 2" from the wall end as
shown. Install the second anchor clip 24" on center from the wall
end. (If end cap leg is other than 24" adjust clip accordingly.)
Rev. 12/09
VAULTED PARAPET INSTALLATION
FORMED COPING
COPING CAP ANCHOR CLIP
#9 x 1-1/2"
SS SCREW w/
NEOPRENE
WASHER, TYP.
ROOF
Clip = Wall + 3/8" SIDE
OFFSET Cap = Wall + 1-1/4"
1-1/2" SS RING
SHANK NAIL ROOFING
Wall MEMBRANE
A
(4) SCREWS
PER CLIP TOP
(1) NAIL PER
D INSIDE CORNER
SUPPORT TOP
B E
E C
(2) NAILS PER CLIP
FACE IF FACE IS >6"
E
C (2) NAILS PER OUTSIDE
INSIDE CORNER
OUTSIDE CORNER CORNER SUPPORT FACE
Vaulted to Flat Wall Vaulted to Flat Wall
Transition Miter Transition Miter
Rev. 12/09
HOOK FRONT
SNAP BACK
ROOF
ROOF SIDE
SIDE
L
FLAT
END TERM
VAULTED VAULTED
END
CAP
58" L
COPING
STRAIGHT
LENGTH
WALL
END
COPING
STEP 2: Installing Anchor Clips at Wall Ends MITER
Install the first anchor clip approximately 2" from the wall end as
shown. Install the second anchor clip 24" on center from the wall
end. DO NOT place second clip at joint location. (If end cap leg is
other than 24" adjust clip accordingly.)
ROOF SIDE
ROOF SIDE
VA
UL
TE
3" 3"
D
D
VA
UL
TE
STEP 6: Installing Vaulted Coping Lengths
Begin installing from the corners and ends working inward to the
3" 3" center. Allow a 1/4" gap between the coping sections for
thermal expansion. Lengths of all vaulted pieces should be
considered prior to cutting to avoid creating relatively short sections
OUTSIDE CORNER INSIDE CORNER of cap adjacent to full length sections. There should be an anchor clip
at least every 60" O.C. (Clip spacing may vary). Every fifth 60"
STEP 3: Installing Corner Support Clips section of coping should be secured to the clip using a single
Two (2) corner support clips are to be placed at all corners to stainless steel screw or rivet (same procedure as STEP 5) to isolate
support the cap. Secure clips using 1-1/2" ss ring shank nails. Set movement within a containment zone.
each clip away from the corner approximately 3".
Rev. 12/09
SPECIAL CONDITION INSTALLATION
CLEATS ONLY SHOW FOR CLARITY. SEE PAGE 3 FOR
SPLICE AND CAP DRAWINGS.
2" EXAMPLE 2
2 CORNER
INLINE TRANSITION SUPPORTS
NOTE: Instructions are for
face leg and back leg offsets.
'L1' 'L'
STEPS:
1. Install cleat 1 2" from offset, use only if wide wall cap leg
length is longer than 20". PIER END TRANSITION
2. Install cleats 2 centered under cap ends. NOTE: Instructions are for
face leg and back leg offsets.
STEPS:
CORNER
1. Install cleat 1 only if 'L' is longer than 12".
SUPPORTS
2. For 'L1' cleats and corner supports, see below.
2 3. Install cleats 2 centered under cap ends.
EXAMPLE 1
'Z' MITER
NOTE: Instructions work for 2 1 2
face leg on either side.
CORNER
'L1' 'L' SUPPORTS
STEPS:
1. Install cleat 1 only if 'L' is longer than 12".
2. For 'L1' procedures see table below.
3. Install cleats 2 centered under cap ends.
Rev. 12/09