Review Problem 1. An iron column of annular cross-section has an outer diameter of 200mm and is subjected to a force of 75 kN. Find the thickness of the wall if the allowable compressive stress is 10 Mpa. a. 12.75 mm c. 12.57 mm b. 17.75 mm d. 15.75 mm 2. A steel tie rod on bridge must be made to withstand a pull of 5000 lbs. Find the diameter of the rod assuming of safety of 5 and ultimate stress of 64,000 psi. a. 0.75 c. 0.71 b. 0.84 d. 0.79 3. Compute the safe wall thickness of a 76.2 cm diameter steel tank. The tank is subjected to 7.33 Mpa pressure and the steel material has a yield stress of 215.4 Mpa. The factor of safety to is 3. a. 1.95 cm c. 3.89 cm b. 4.09 cm d. 3.96 cm 4. A cylindrical water tank is 8 m in diameter and 12 m high. If the tank is to be completely filled, determine the minimum thickness of the tank plating if the stress is limited to 40 Mpa. a. 11.77 mm c. 13.18 mm b. 10.25 mm d. 12.6 mm 5. A 2-inch solid shaft is driven by a 36-inch gear and transmits power at 120 rpm. If the allowable shearing stress is 12 ksi, what horsepower can be transmitted? a. 29.89 c. 35.89 b. 38.89 d. 34.89 6. A hollow shaft has an inner diameter of 0.035 m and an outer diameter of 0.06 m. Compute for the torque in N-m, if the stress is not to exceed 120 Mpa. a. 4500 c. 4100 b. 4300 d. 4150 7. Determine the length of the shortest 2 mm diameter wire which can be twisted through two complete turns without exceeding a shearing stress of 70 MPa and using Modulus of rigidity 35 GPa. a. 3.14 m c. 4.31 m b. 6.28 m d. 8.26 m 8. What is the modulus of elasticity if the stress is 44,000 psi and unit strain of 0.00105? a. 41.905 x 106 c. 42.300 x 106 b. 41.202 x 106 d. 43.101 x 106 9. A steel wire 10 m long hanging vertically support a load of 2000 N. Neglecting the weight of the wire, determine the required diameter, if the stress is not to exceed 140 MPa and total elongation is not to exceed 5 mm, E = 200 GPa. a. 6.739 mm c. 8.694 mm b. 4.026 mm d. 5.046 mm 10. An iron steam pipe is 200 ft long at 0o C. what will its increase in length when heated to 100 o C? Coefficient of linear expansion is 10 x 10 -6 /o C. a. 0.18 ft c. 0.12 ft b. 0.28 ft d. 0.20 ft 11. A flanged bolt coupling of eight steel 20 mm diameter bolts spaced evenly around a bolt circle 300 mm in diameter. Determine the torque capacity of the coupling if the allowable stress shearing stress in the bolt is 40 MN/m2. a. 15.1 kN-m c.17.5 kN-m b. 14.6 kN-m d. 13.6 kN-m 12. A simple beam 10 m long carries a concentrated load of 200 kN at the midspan. What is the maximum moment of the beam? a. 250 kN-m c. 500 kN-m b. 400 kN-m d. 100 kN-m 13. A simply supported beam, 10 m long carries a uniformly distributed load of 20 kN/m. What is the value of the maximum shear of the beam due to this load? a. 250 kN c. 100 kN b. 1000 kN d. 500 kN 14. A beam 6 m long is simply supported and loaded by a uniformly varying distributed load with zero intensity at the left and 50 kN/m at the right. Find the location of the maximum bending moment. a. 3 m c. 3.46 m b. 4 m d. 3.76 m 15. A simply supported rectangular beam 50 mm wide and 100 mm deep carries a uniformly distributed load of 1200 N/m over its entire length. What is the maximum length of the beam if the flexural stress is limited to 20 Mpa. a. 10 m c. 11 m b. 3.33 m d. 15 m Thank You & Stay Safe!!!