Professional Documents
Culture Documents
LiquaROAM E-Flex Fitting Instructions 09102014RCT 04 With Vent
LiquaROAM E-Flex Fitting Instructions 09102014RCT 04 With Vent
LiquaROAM LLC, 2646 South Loop West, Suite 405, Houston, Texas, 77054 USA.
Phone (713) 664 4030, Fax (713) 664 3732, Mobile (713) 478 8441
rev 04 - 09102014 1
Fitting instructions
E-Flex Easy Flexitank
rev 04 - 09102014 2
• Ensure that only containers that have been
heavy weight tested to a minimum of 30,480
kilograms are used.
• Ensure the containers are no older than 5 years.
• Ensure that containers are in excellent condition.
• No repair on side walls and no damages on the
floor.
• Foodgrade containers only – free of odors.
rev 04 - 09102014 3
• Sweep the container carefully with a broom.
• Ensure that nails and other objects that may damage/puncture the flexitank are removed.
• Cover potential uneven areas on the walls and on the floor with duck tape (thick tape).
rev 04 - 09102014 4
Open the E-flex box and ensure that the following are in the package:
1. E-flex
2. Warning labels
3. Two cable ties
4. Adhesive Tape
rev 04 - 09102014 5
Position the E-flex to the edge of the left door.
Unroll the E-flex into the container.
Make sure not to step on the E-flex while unrolling.
Make sure not to wear shoes during the fitting operation.
The door end of the E-Flex should be at the point
where the wooden floor side meets the metal door
frame.
rev 04 - 09102014 6
E-Flex Flexible Harness…
E-flex has to be fastened to the lashing rings in the
container to avoid sliding during transportation.
Not all containers have the same lashing ring
configuration. Approximate your container to the
drawing.
rev 04 - 09102014 7
BELT TYING 1 : NOSE DIRECTION
rev 04 - 09102014 8
BELT TYING 2 : DOOR DIRECTION
rev 04 - 09102014 9
BELT TYING 3 :
rev 04 - 09102014 10
Vent System (Optional)
rev 04 - 09102014 11
Vent System (Optional)
rev 04 - 09102014 12
Vent System (Optional)
rev 04 - 09102014 13
Vent System (Optional)
rev 04 - 09102014 14
Vent System (Optional)
rev 04 - 09102014 15
DOOR PROTECTION :
Although 20cm free space remains between E-flex and the doors after filling, a protective
operation against the sharp edges of the bolts on the doors is required.
The box will be used as a door protector. Collapse the box as shown.
rev 04 - 09102014 16
DOOR PROTECTION : OPTION 1
If the fitting operation is being done at the filling location, place the board
between the E-flex and doors.
Please ensure that plastic supported area which remains between the two sides
of the collapsed box, is downwards.
rev 04 - 09102014 17
DOOR PROTECTION : OPTION 2
If the filling and fitting areas are different then please follow the below instructions.
Cut the board into two pices from the joint corners.
rev 04 - 09102014 18
Fix the cut pieces of the board to the door by the provided adhesive tapes.
rev 04 - 09102014 19
• Fill in the provided Check List and stick it to the door on the right hand side
rev 04 - 09102014 20
WARNING:
IMPROPER FITTING MAY CAUSE CAPACITY PROBLEMS, INNER LAYERS MAY GET
STUCK AND STRETCH. THIS MAY CAUSE SEVERE LEAKINGS.
rev 04 - 09102014 21
• We have 2 or 3 inch valve alternatives.
• Valves have male cam-lock connection.
• According to your 2 or 3 inch preference you will need to have a female camlock
coupling.
rev 04 - 09102014 22
READY FOR FILLING...
rev 04 - 09102014 23
• Connect the hose to the valve.
• Make sure that protective bonnet spout is unrolled.
• Make sure that the hose is suspended at the top of the container by using a strap.
• Make sure that you have chosen a light weight filling hose.
rev 04 - 09102014 24
• Start loading the E-flex.
• WARNING:
• Ensure that the start up pumping speed does not exceed 300 lt /min (80 GPM) until the E-flex
rises to an approximate height of 50 cm (roughly the first 5-6,000 litres) , then increase the
speed up to 800lt/min (210 GPM). Please ensure that the filling stations follow this instruction
carefully.
• Generally filling will take aproximattely 50 minutes.
rev 04 - 09102014 25
• When the flexitank is loaded, remove the hose.
• Attach the cap of the valve and fasten it.
• Fasten the bonnet cover with a cable tie over the body of the valve.
• Twist the bonnet and make a “swan-neck” folding.
• Fasten with the provided second cable tie once again.
rev 04 - 09102014 26
Bonnet Closure...
E-flex has two protective bonnets around the inlet to prevent contamination and to act as secondary
containment in case of an incident.
Ensure that Bonnet is well tied according to our instructions.
rev 04 - 09102014 27
Bonnet Closure...
4 5 6
rev 04 - 09102014 28
WARNING LABELS:
rev 04 - 09102014 29
rev 04 - 09102014
30
Thank you for choosing
E-Flex Easy Flexitank
THANK YOU ON BEHALF OF:
&
ROAM Tank Systems LLC
2646 South Look West, Suite 405
Houston, TX 77054
713-664-4030
jmrose@roamfluidsolutions
www.roamfluidsolutions.com
rev 04 - 09102014
31