Professional Documents
Culture Documents
ORDER INFORMATION
Material Item No.
with
Door overlay View Cranking Slide-on
Cup Arm spring
Screw fixing
Steel, Zamak,
Full overlay 0 ■ F016073066
nickel-plated nickel-plated
Steel, Zamak,
Half overlay 8 ■ F016073068
nickel-plated nickel-plated
Steel, Zamak,
Inset 15 ■ F016073069
nickel-plated nickel-plated
COVER CAPS
Designation Cranking Imprinted/Embossed Item No.
Hinge arm cover cap, steel, short, nickel-plated, not imprinted,
0 On request F069073570
Soft-close compatible
ACCESSORIES
Designation Item No. Designation Item No.
Nexis Slide-on mounting plates 270 Soft-close Pin 290 Assembly aids 358
Accessories 274 Technical information 276
244 Packaging units are not covered in this brochure; please enquire with your supplier
Hinge systems
Nexis Slide-on 25
59
60
3-6
3-11 3-11
Tiomos
F 2xF F
F
18 11 26 3
35 6
Nexis
3 4 5 6 7 8 9 10 11 3 4 5 6 7 8 9 10 11 3 4 5 6
24 0 16 0 0 2 3 4
23 0 15 0 1 2 3 4
22 0 2 14 0 2 2 3 4
21 0 2 3 13 0 2 3
20 0 2 3 4 12 0 2 3 4
19 0 2 3 4 11 0 2 3 4
Special
hinges
18 0 2 3 4 10 0 2 3 4
17 0 2 3 4 9 0 2 3 4
Door overlay
Door overlay
Door reveal
16 0 2 3 4 8 0 2 3 4
15 2 3 4 7 2 3 4
14 2 3 4 6 2 3 4
Mounting plate height Mounting plate height Mounting plate height
Single-joint
MINIMUM GAP MINIMUM REVEAL NOTES
hinges
Cup distance Cup distance The minimum gap is the clearance
3 4 5 6 8 10 3 4 5 6 8 10 required between the front edge of the
20 0.0 0.0 0.0 0.0 0.0 0.0 20 0.1 0.1 0.1 0.1 0.1 0.1 cabinet and the closed door so that the
22 0.0 0.0 0.0 0.0 0.0 0.0 22 0.2 0.2 0.2 0.2 0.2 0.2 door can open without hindrance.
24 0.0 0.0 0.0 0.0 0.0 0.0 24 0.3 0.3 0.3 0.3 0.3 0.3
Cabinet making
Important: The reveals were calculated
accessories
26 0.0 0.0 0.0 0.0 0.0 0.0 26 0.4 0.4 0.4 0.4 0.4 0.4
for doors with a radius of 1 mm!
28 0.0 0.0 0.0 0.0 0.0 0.0 28 0.6 0.6 0.6 0.6 0.6 0.6
Door thickness
Door thickness
30 0.0 0.0 0.0 0.0 0.0 0.0 30 0.8 0.8 0.8 0.8 0.8 0.8 Hinge dimensions and reveal calculation
32 0.0 0.0 0.0 0.0 0.0 0.0 32 2.1 1.1 1.1 1.1 1.1 1.1 with factory setting.
34 0.0 0.0 0.0 0.0 0.0 0.0 34 4.2 3.1 2.3 1.6 1.4 1.4 We recommend a trial fitting.
36 0.0 0.0 0.0 0.0 0.0 0.0 36 6.5 5.2 4.2 3.5 2.2 1.7
Minimum gap Minimum reveal (F)