USER MANUAL Common +---------------------------+ R1 Relay Selected Event [1].Relay1: Summary Alarm [2].Relay2: Power Fail R2 [3].Relay3: Battery Low [4].Relay4: On Bypass R3 [5].Relay5: Overload [6] Relay6: Over Temperature R4 [0].Back To Previous Menu
R5 Please Enter Your Choice =>
+5V R6 Once the configuration is complete SW2
CPU Pin MUST be switched to the ON position to apply the new settings, switch SW2 back to the OFF GND-R position to reset to the default settings. Input 3. Press ‘2’ to configure the Input signal. PRESENTATION +---------------------------+ FEATURES | Configure Input Signal | This relay I/O card is an UPS management +---------------------------+ OUTLINE [1].Act as Shutdown or Test: Shutdown product with 6 relay output contacts for monitoring [2].Input Signal Confirm: 3 Seconds GND-R the status and 1 input contact as a shutdown UPS Common [3].Delay Before Shutdown: 30 Seconds R1 or a battery test command. R2 [0].Back To Previous Menu R3 Features: R4 R5 Please Enter Your Choice => z Monitor UPS events. R6 Input
z 6 programmable relay output contacts.
Tx Rx In this menu, the input signal can be redefined z Configurable normal open or normal close for GND-C SW1 as shutdown UPS or battery test signal. SW2 Meanwhile, the UPS shutdown delay time is each relay contact. also adjustable to a maximum of 9999 z Configurable UPS shutdown delay time. I/O PINOUT seconds. z Configurable input signal as shutdown UPS or GND-R: Ground for relays 4. Press ‘3’ to configure the normal open or battery test. normal close for each relay. Common: 12~24VDC z Has the ability to protect up to 6 computers +---------------------------+ Default Alarm Event unattended shutdown gracefully. | Customize Output Relay | R1 Summary Alarm +---------------------------+ R2 Power Fail Relay Selected Event TECHNICAL SPECIFICATION [1].Relay1: Normal Close R3 Battery Low TECHNICAL SPECIFICATION [2].Relay2: Normal Open R4 On Bypass [3].Relay3: Normal Close Size 130 x 60 mm R5 Overload [4].Relay4: Normal Open Weight 200 g [5].Relay5: Normal Close R6 Over Temperature Operating Temperature 0 ~ 40° C [6].Relay6: Normal Open Input: Remote shutdown or battery test [0].Back To Previous Menu Operating Humidity 10 ~ 80 % Tx: Transmit to PC, connect to sub9-pin2 Power Input 8 ~ 20V DC Please Enter Your Choice => Rx: Receive from PC, connect to sub9-pin3 Power Consumption 1.2 Watts Once the configuration is complete SW2 GND-C: Ground for configuration Tx and Rx pins OFF (Default) ON MUST be switched to the ON position to apply OUTPUT CONTACT RATING the new settings. Switch SW2 back to the SW1 Normal open Normal close Maximum OFF position to reset to the default settings. for default settings for default settings DC Voltage DC Current 5. Press ‘0’ to quit this configuration session. SW2 Default settings Customized settings Relay The system would prompt you to save or not. 24 V 1A R1~R6 Press ‘Y’ to save your settings, ‘N’ to ignore. PROGRAMMABLE CONTACTS INPUT RATING COMMUNICATION SETUP POWER OPTION IN WIN 2000/XP Maximum 1. Connect Tx to pin2, Rx to pin3 and GND-C to This relay card has the ability to provide UPS DC Voltage DC Current pin5 of PC RS232 port. signals for Windows NT4/2000/XP/2003. First Input 24 V 10 mA 2. In the Windows environment, launch the connect the RS232 port on the PC to the relay Hyper- Terminal program then open the card as shown: APPLICATION EXAMPLE specified COM port. Then open the power option from control panel 3. Set the following properties: and click on the UPS tab to setup the signals In this case we’ll use the default settings, please Baud rate: 2400, Data Bits: 8, Parity: None polarity, select Positive for Power Fail, Low set SW1 and SW2 to the OFF position. Apply Stop Bit: 1, Flow Control: None Battery and UPS 12VDC to Common contact and connect the Common lamps to R1~R6 terminals. Install a push button RTS pin7 Shutdown. CONFIGURATION GND-R Since the R1~R6 from the Common contact to the input terminal. GND pin5 1. Press <Enter> to get the main menu of the contacts are Press the button for at least 3 seconds to R1 programmable relay card. programmable, shutdown the UPS remotely. Power Fail R2 Common +12V +---------------------------+ CTS pin8 the output | UPS Relay Card | Battery Low R3 contacts can be GND-R +---------------------------+ DCD pin1 Firmware Version: Relay Card V1.4 R4 configured for 3 R1 Summary Alarm [1].Customize Output Relay computers with 2 R2 [2].Configure Input Signal R5 signals (power fail Power Fail [3] Customize Normal Open or Normal Close R3 [0].Quit R6 and low battery) or Battery Low Shutdown UPS Input 6 computers with R4 On Bypass Please Enter Your Choice => DTR pin4 one signal (power R5 Overload 2. Press ‘1’ to configure the alarm event for fail or low battery). R6 R1~R6. Over Temperature Input Contacts R1~R6 can be configured for Note: All of the computers must have the same Shutdown UPS different power events. earth ground potential. Connect all of the computers input power to the same UPS.