Paralistforumts Huawei Good

BSC6900 UMTS V900R013C00
Parameter Reference
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support and service. For any assistance, ple
company headquarters.
Huawei Technologies Co., Ltd.

Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Email: support@huawei.com
Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.

No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huaw
Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective holders.
d service. For any assistance, please contact our local office or
hout prior written consent of Huawei Technologies Co., Ltd.
espective holders.
Purpose
This document provides information about the BSC6900 parameters, including the meaning, value, and usage of the
Intended Audience
•Network planners
•Field engineers
•System engineers
•Shift operators
Organization
Each parameter is described in the following aspects.
Description
MO
Parameter ID
Parameter Name
NE
MML Command
Meaning
IsKey
Mandatory
Feature ID
Feature Name
Value Type
GUI Value Range
Enumeration Number/Bit
Unit
Actual Value Range
Default Value
Recommended Value
Impact
Parameter Relationship
Access
Service Interrupted After Modification
Interruption Scope
Interruption Duration (min)
Caution
Validation of Modification
Impact on Radio Network Performance

Introduced in Version
Attribute
about the BSC6900 parameters, including the meaning, value, and usage of the parameters.
following aspects.
Remarks
Managed object of NE
Simple string for identifying a parameter
Name of the parameter
NEs on which the parameter is set
Commands for setting the parameter
Definition, purpose, and protocols of the parameter
Whether the parameter is used to identify an MO instance
Whether the parameter is mandatory for creating an MO instance
ID of the feature that uses the parameter
Name of the feature that uses the parameter
Parameter value type
Parameter value range displayed on the GUI
Enumeration number corresponding to the GUI value of a parameter of the enumeration

type, or bit position corresponding to the GUI value of a parameter of the bit field type
Parameter value unit

Actual parameter value range corresponding to the GUI Value Range
Initial parameter value assigned by the system. There is no default value for a mandatory
parameter. None indicates that there is no default value. For a bit field parameter, the value
ON of a sub-parameter means that the bit representing the sub-paramet
Parameter values recommended for different scenarios

Parameter impact scope, that is, objects specified when the parameter is set
Relationship between this parameter and other parameters. For example, to use this
parameter, you need to set related switches and parameters.
Whether this parameter is Read & Write or Read Only.
Whether modifying the parameter value interrupts the ongoing services
Possible interruption scope
Possible interruption duration (unit: minute)
Cautions to be taken during the modification
How this parameter takes effect and whether the equipment needs to be restarted after the
modification
Impact of the parameter on radio network performance
Product version in which the parameter is introduced
Whether the parameter is a radio parameter, a transport parameter, or an equipment
parameter
MO Parameter ID Parameter Name
UDPUCFGDATA MaccPageRepeatTimes Repeat Times of Macc Paging
AAL2PATH ANI Adjacent Node ID
AAL2PATH PATHID AAL2 path ID
AAL2PATH CARRYT Bearing type
AAL2PATH CARRYF Bearing subrack No.
AAL2PATH CARRYSN Bearing slot No.
AAL2PATH CARRYUNILNKN Bearing UNI link No.
AAL2PATH CARRYIMAGRPN Bearing IMA group No.
AAL2PATH CARRYFRAATMLNKN Bearing FRAATM link No.
AAL2PATH CARRYNCOPTN Bearing NCOPT port No.
AAL2PATH CARRYVPN Bearing ATM logic port No.

AAL2PATH RSCGRPFLAG Add To Rscgrp Flag
AAL2PATH RSCGRPN Rscgrp No.
AAL2PATH VPI Bearing VPI
AAL2PATH VCI Bearing VCI
AAL2PATH TXTRFX TX traffic record index
AAL2PATH RXTRFX RX traffic record index
AAL2PATH OWNERSHIP AAL2 path ownership
AAL2PATH TRMLOADTHINDEX TRM load threshold index
AAL2PATH TIMERCU Timer_CU timer

AAL2PATH AAL2PATHT AAL2 Path Type
AAL2RT NSAP Destination ATM address
AAL2RT ANI Adjacent Node ID
AAL2RT RTX Route index
Destination ATM address

AAL2RT OWNERSHIP ownership
AAL2TMR ESTREQTMR Establishment request timer
AAL2TMR ESTINDTMR Establishment indication timer
AAL2TMR RELREQTMR Release request timer
AAL2TMR RELINDTMR Release indication timer
AAL2TMR BLOREQTMR Blocking request timer
AAL2TMR UBLREQTMR Unblocking request timer
AAL2TMR RESREQTMR Reset request timer

AAL2TMR MODREQTMR AAL2 modifying request timer
AAL2TMR MODINDTMR AAL2 modifying indication timer
ADJMAP ANI Adjacent Node ID
ADJMAP ITFT Interface Type
Transport Type of the adjacent

ADJMAP TRANST node and interface type
ADJMAP CNMNGMODE Resource Management Mode
ADJMAP CNOPINDEX CN Operator index
ADJMAP TMIGLD Gold user TRMMAP index
ADJMAP TMISLV Silver user TRMMAP index

ADJMAP TMIBRZ Bronze user TRMMAP index
ADJMAP FTI Factor table index
ADJMAP LEIGLD Gold user Load EQ index
ADJMAP LEISLV Silver user Load EQ index
ADJMAP LEIBRZ Bronze user Load EQ index
ADJNODE ANI Adjacent Node ID
ADJNODE NAME Adjacent Node Name
ADJNODE NODET Adjacent Node Type
ADJNODE NODEBID NodeB ID
ADJNODE SGSNFLG SGSN FLAG
ADJNODE TRANST Transport Type
ADJNODE DPX DPX Index

ADJNODE IsROOTNODE Is Root Node
ADJNODE UPPERANI Upper Ani
ADJNODE SRN Subrack No.
ADJNODE SN Slot No.
ADJNODE SAALLNKN SAAL link No.
ADJNODE QAAL2VER Qaal2 Protocol Version
ALMBLKPARA AID Alarm ID
ALMBLKPARA BLKPRD Alarm blink threshold

Upper count threshold of raised
ALMBLKPARA CNTRISTHRD fault
Lower count threshold of raised

ALMBLKPARA CNTSTLTHRD fault
Upper time threshold of raised
ALMBLKPARA TMRISTHRD fault
Lower time threshold of raised

ALMBLKPARA TMSTLTHRD fault
ALMBLKSW BLKFILTERSW Alarm switch of blinking filter
ALMBLKSW BLKSTATSW Switch of statistics blinking alarm
Observing time window of

ALMBLKSW BLKSTATPRD statistical alarm
ALMCAPACITY MAXNUM Max Alarm Log Number
ALMCAPACITY SD Alarm Log Saved Time
ALMFLT CSN Serial No.
ALMLVL AID Alarm ID
ALMLVL ALVL Alarm Severity
ALMML LEVEL Alarm Mask Switch
ALMPORT SRN Subrack No.
ALMPORT PN Port No.
ALMPORT SW Switch
ALMPORT AID Alarm ID
ALMPORT PT Port Type
ALMPORT AVOL Alarm level
ALMPORT UL Upper Limit
ALMPORT LL Lower Limit
ALMSCRN ALVL Alarm Severity
ALMSHLD AID Alarm ID
ALMSHLD SHLDFLG Shield Flag
ASWPARA SW OMU Automatic Switchover Switch

OMU Automatic Switchover
ASWPARA INTV Interval
ASWPARA AUTORESUMESW Auto Turn On Switch
ATMLOGICPORT SRN Subrack No.
ATMLOGICPORT SN Slot No.

ATMLOGICPORT LPNTYPE Type of the logic port
ATMLOGICPORT BT Board type
ATMLOGICPORT LPN The logic port number
ATMLOGICPORT CARRYT The bearing type of the logic port
ATMLOGICPORT CARRYSN Bearing slot No.
ATMLOGICPORT CARRYIMAGRPN IMA group No.
ATMLOGICPORT CARRYUNILNKN Bearing UNI link No.
ATMLOGICPORT CARRYFRAATMLNKN FRAATM link No.
ATMLOGICPORT CARRYPN Optical port No.
ATMLOGICPORT UPPERVP The Upper Logic port Number
ATMLOGICPORT TXBW Forward bandwidth [kbps]
ATMLOGICPORT RXBW Backward bandwidth [kbps]
ATMLOGICPORT RSCMNGMODE Resource management mode
ATMLOGICPORT CNOPINDEX CN operator index
ATMLOGICPORT FLOWCTRLSWITCH Flow control switch
ATMLOGICPORT FCINDEX Flow control parameter index
ATMLOGICPORT TRMLOADTHINDEX TRM load threshold index
ATMLOGICPORT LPN The logic port Number
ATMLOGICPORT FCINDEX Flow control parameter index
ATMLOGICPORT TRMLOADTHINDEX TRM load threshold index
ATMTRF TRFX Traffic index

ATMTRF ST Service type
ATMTRF UT Rate unit
ATMTRF PCR Peak cell rate
ATMTRF SCR Sustainable cell rate
ATMTRF MCR Minimum cell rate
ATMTRF MBS Max burst size
ATMTRF CDVT Cell delay variation tolerance
ATMTRF REMARK Purpose description
BFDPROTOSW SRN Subrack No.
BFDPROTOSW SN Slot No.
BFDPROTOSW SWITCH Bfd Protocol Switch
BOXRPT AID Alarm ID
BOXRPT BOXFLG To Alarm Box Flag
BRD SRN Subrack No.

BRD SN Slot No.
BRD BRDCLASS Board Class
BRD RED Backup
BRD BRDTYPE Board type
BRD BRDCLASS Board Class
BRD BRDTYPE Board Type
BRD LGCAPPTYPE Logical function type
BRD RED Backup
BRD MPUSUBRACK MPU Subrack No.
BRD MPUSLOT MPU Slot No.
BRD ISSUPPORTFRA Support FRA
BRD PORTWORKMODE Port Work Mode
CAB CN Cabinet No.
CAB PWRMODE Cabinet power mode
CAB CN Cabinet No.
CCG CG Command Group
CCG CMD Command Name

CCGN CG Command Group
CCGN CGN Command Group Name
CERTFILE RootCert Root Certificate File Name
CERTFILE PubCert Certificate File Name
CERTFILE PrivKey Private Key File Name
Private Key Password Enabled

CERTFILE PKPEnableSta State
CERTFILE PWD Private Key Password
Certificate Revocation List File

CERTFILE CRLEnableSta State
Certificate Revocation List File
CERTFILE CRL Name
Certificate Chain File Enabled

CERTFILE CCAEnableSta State
CERTFILE CertChain Certificate Chain File Name
CFGDATAEFFECTIVE SRN Subrack No.
CFGDATAINEFFECTIVE SRN Subrack No.
CFMMA SRN Subrack No.
CFMMA SN Slot No.
CFMMA MDIDX MD Index
CFMMA VLANID VLAN ID
CFMMA MAIDX MA Index
CFMMA MANAME MA Name
CFMMA CCMINTERVAL CCM Send Prid
CFMMD SRN Subrack No.
CFMMD SN Slot No.

CFMMD MDIDX MD Index
CFMMD Level MD Level
CFMMD MDName MD Name
CFMMD SRN Subrack No.
CFMMEP SRN Subrack No.
CFMMEP MAIDX MA Index
CFMMEP MEPTYPE MEP Type
CFMMEP MEPID MEP ID
CFMMEP PORTTYPE Port Type
CFMMEP SN Slot No.
CFMMEP PN Port No.
CFMMEP TRUNKN Trunk No.
CLK SRT Subrack type
CLK SRN Subrack No.
CLK SN Slot No.
CLK BT Board type
CLK REF2MCLKSRC Port for LINE1
CLK SUPPORTBAKCLKSRC Use Back-up port for LINE1
CLK REF2MCLKSRCBAK Back-up port for LINE1
CLK REFUSELOCALCLK Use SGSN clock source
CLK REF2MCLKSW1 Switch of panel 2M BITS1

CLK REF2MCLKSW2 Switch of panel 2M BITS2
CLK BACK8KCLKSW1 Switch of backplane LINE1
CLK BACK8KCLKSW2 Switch of backplane LINE2
CLKMODE MODE System clock working mode
CLKMODE SRCGRD Clock source priority
CLKSRC SRCGRD Clock source priority
CLKSRC SRCT Clock source type
CLKTYPE CLKTYPE Clock board type
CMCTRLSW CTRLSW CM Control Enable Switch
CONNTYPE CONNTYPE Connection Type
COPTLNK SRN Subrack No.
COPTLNK SN Slot No.
COPTLNK BT Board Type
COPTLNK PS Port select

COPTLNK PN Port No.
COPTLNK E1T1PN E1/T1 port No.
COPTLNK J2MODE J2 length
COPTLNK J2BYTE_FORMAT J2 Byte Format
COPTLNK J2TXVALUE J2 transmit value
COPTLNK J2RXVALUE J2 expected incept value
COPTLNK JAUTOADD Automatic Append J Byte
CORRM CellId Cell ID
Cell-Oriented Service Distribution

CORRM MbscServiceDiffLdbSw and Load Balancing Switch
Load Difference Threshold

Between 3G And 2G Of CS
CORRM MbscLdBlcCsDeltaThrd Service
PS Load Difference Threshold

Between 3G And 2G Of Ps
CORRM MbscLdBlcPsDeltaThrd Service
CPUTHD BRDCLASS Board Class

CPU occupancy alarm clearance
CPUTHD SSCPUAVEUSAGEALMTHD threshold
CPUTHD SSCPUMAXUSAGEALMTHD CPU occupancy alarm threshold

DSP occupancy alarm clearance
CPUTHD SSDSPAVEUSAGEALMTHD threshold
CPUTHD SSDSPMAXUSAGEALMTHD DSP occupancy alarm threshold

SSTHRUPUTAVEUSAGEALMTH Thruput Occupancy Alarm
CPUTHD D Clearance Threshold
SSTHRUPUTMAXUSAGEALMTH Thruput Occupancy Alarm
CPUTHD D Threshold
CTRLFACTOR TYPE Application Type
CTRLFACTOR FACTOR Factor
DB FN File Name
DEVIP SRN Subrack No.
DEVIP SN Slot No.
DEVIP DEVTYPE Device IP Address Type
DEVIP IPADDR IP address
DEVIP MASK Subnet mask
DEVIP MTU MTU[Byte]
DHCPRLY DHCPRLYID DHCP Relay ID
DHCPRLY DHCPRLYGATEWAYIP DHCP Relay Gateway IP Address
DSCPMAP DSCP Differentiated Service Codepoint
DSCPMAP VLANPRI VLAN Priority
E1T1 SRN Subrack No.
E1T1 SN Slot No.
E1T1 BT Board type

E1T1 PS Port select
E1T1 PN Port No.
E1T1 UNBA Support Balance
E1T1 WORKMODE Work Mode
E1T1 PTTYPE Frame Structure
E1T1 PTTXT Frame send Structure
E1T1 PTRXT Frame receive Structure
E1T1 PTCODE Line code
E1T1 SCRAMBLESW Scramble Switch
E1T1 TS16ENABLE 16TimeSlot switch
E1T1 LOOPSW Loop Detect Switch

E1T1 REMARK Remark
E1T1LOP SRN Subrack No.
E1T1LOP SN Slot No.
E1T1LOP BT Board type
E1T1LOP PN Port No.
E1T1LOP LOPT Loop type
E1T1LOP LLCN Channel No.
E1T1LOP RLCN Channel No.
E1T1LOP AUSTOP Loop time[min]
EMSIP EMSIP EMS IP Address

EMSIP MASK Subnet mask
EMSIP OMUIP OMU External Network Virtual IP
EMSIP OMUMASK OMU External Network Mask
EMU SRN Subrack No.

Enable Alarm Reporting for 48V
EMU VOL48_MASK Power
Enable Alarm Reporting for 24V
EMU VOL24_MASK Power
Enable Temperature Alarm
EMU TEMP_MASK Reporting
EMU HUM_MASK Enable Humidity Alarm Reporting
EMU WATER_MASK Enable Water Alarm Reporting
EMU SMOKE_MASK Enable Smoke Alarm Reporting
EMU INFRA_RED_MASK Infrared alarm switch

Enable Door Status Alarm
EMU DOOR_ENGINE_MASK Reporting
EMU EX_ANO1_TYPE Sensor Type of External Analog 1

Upper Limit of Alarm for 48V
EMU VOL48_THD_HIGH Power
Lower Limit of Alarm for 48V
EMU VOL48_THD_LOW Power
Upper Limit of Alarm for 24V
EMU VOL24_THD_HIGH Power
Lower Limit of Alarm for 24V
EMU VOL24_THD_LOW Power
EMU TEMP_THD_HIGH Upper Limit of Temperature Alarm
EMU TEMP_THD_LOW Lower Limit of Temperature Alarm
EMU HUM_THD_HIGH Upper Limit of Humidity Alarm
EMU HUM_THD_LOW Lower Limit of Humidity Alarm

Upper Limit of Signal Output of
EMU EX_ANO1_SIG_MAX External Analog 1
Lower Limit of Signal Output of
EMU EX_ANO1_SIG_MIN External Analog 1
Upper Limit of Measurement
EMU EX_ANO1_VAL_MAX Range of External Analog 1
Lower Limit of Measurement
EMU EX_ANO1_VAL_MIN Range of External Analog 1
EMU POWER_RELAY1 Switch for Relay 1
ENVALMPARA AID Alarm ID
ENVALMPARA ANM Alarm Name
ENVALMPARA ALVL Alarm Severity

ENVALMPARA ASS Event Type
ETHIP SRN Subrack No.
ETHIP SN Slot No.
ETHIP PN Port No.
ETHIP IPINDEX IP address index
ETHIP IPADDR Local IP address
ETHIP MASK Subnet mask
ETHIP MASK Subnet mask
ETHPORT SRN Subrack No.
ETHPORT SN Slot No.
ETHPORT BRDTYPE Board type.
ETHPORT PTYPE Port type
ETHPORT PN Port No.
ETHPORT AUTO Auto negotiation
ETHPORT SPEED Port speed

ETHPORT MTU MTU[Byte]
ETHPORT FC Physical layer flow control switch
ETHPORT OAMFLOWBW OAM flow min bandwidth[%]
ETHPORT FLOWCTRLSWITCH Flow control switch
ETHPORT FCINDEX Flow control parameter index
ETHPORT ERRDETECTSW Error-frame detect switch
ETHPORT ERRALARMTHD Error-frame alarm threshold
Received broadcast packets alarm

ETHPORT BCPKTALARMTHD threshold[packet/s]
Received broadcast packets alarm
ETHPORT BCPKTALARMCLRTHD clear threshold[packet/s]
ETHPORT CFMVER CFM Protocol Version
ETHREDPORT SRN Subrack No.
ETHREDPORT SN Slot No.
ETHREDPORT PN Port No.
ETHTRK SRN Subrack No.

ETHTRK SN Slot No.
ETHTRK TRKN Trunk No.
ETHTRK WORKMODE Trunk group work mode

ETHTRK SYSPRI Trunk system priority
ETHTRK RT Revertive type
ETHTRK LACPMODE Aggregation Mode
ETHTRK OAMFLOWBW OAM flow min bandwidth[%]
ETHTRK FLOWCTRLSWITCH Flow control switch
ETHTRK FCINDEX Flow control parameter index
ETHTRK CFMVER CFM Protocol Version
ETHTRKIP SRN Subrack No.
ETHTRKIP SN Slot No.
ETHTRKIP TRKN Trunk No.
ETHTRKIP IPINDEX IP address index
ETHTRKIP IPADDR Local IP address
ETHTRKIP MASK Subnet mask
ETHTRKLNK SRN Subrack No.
ETHTRKLNK SN Slot No.
ETHTRKLNK TRKN Trunk No.
ETHTRKLNK TRKLNKSN Trunk Link Slot No.
ETHTRKLNK TRKLNKPN Trunk Link No.
ETHTRKLNK WORKMODE Trunk group work mode

ETHTRKLNK PORTPRI Port priority
FACFG INTERVAL Start Fault Analysis Interval
FACFG PERIOD Fault Analysis Period
FACFG LOGSW Verbose Logging Switch
FANSPEED FANFLAG Fan Type
FANSPEED SRN Subrack No.
FANSPEED FANSPEEDMODE Speed adjustment mode
FANSPEED FANADJUSTCOMMAND2 Duty ratio adjustment command
FCCPUTHD BRDCLASS Board Class
FCCPUTHD SMWINDOW Filter window
FCCPUTHD FDWINDOW Fast judgement window
FCCPUTHD CTHD Critical threshold
FCCPUTHD PRINTCTHD Print control threshold
FCCPUTHD PRINTRTHD Print restore threshold
FCCPUTHD TRACECTHD Debug tracking control threshold
FCCPUTHD TRACERTHD Debug tracking restore threshold

Performance monitor control
FCCPUTHD PMCTHD threshold
Performance monitor restore
FCCPUTHD PMRTHD threshold
FCCPUTHD RESAUDITCTHD Resource Audit control threshold
FCCPUTHD RESAUDITRTHD Resource Audit restore threshold
FCCPUTHD SMPAGECTHD SMS page control threshold
FCCPUTHD SMPAGERTHD SMS page restore threshold

SS and LCS page control
FCCPUTHD SLPAGECTHD threshold
SS and LCS page restore
FCCPUTHD SLPAGERTHD threshold
FCCPUTHD CPAGECTHD Call page control threshold

FCCPUTHD CPAGERTHD Call page restore threshold
FCCPUTHD HANDOVERCTHD Handover control threshold
FCCPUTHD HANDOVERRTHD Handover restore threshold
FCCPUTHD IURULCTHD Iur uplink transfer control threshold
FCCPUTHD IURULRTHD Iur uplink transfer restore threshold

Iur downlink transfer control
FCCPUTHD IURDLCTHD threshold
Iur downlink transfer restore
FCCPUTHD IURDLRTHD threshold
FCCPUTHD CBSCTHD CBS control threshold
FCCPUTHD CBSRTHD CBS restore threshold
FCCPUTHD LOGCTHD Log control threshold
FCCPUTHD LOGRTHD Log restore threshold
FCCPUTHD CELLURACTHD Cell URA update control threshold
FCCPUTHD CELLURARTHD Cell URA update restore threshold

Current XPU CPU share out
FCCPUTHD XPUSHAREOUTTHD threshold
Offset of current CPU load and
FCCPUTHD XPUSHAREINOFFSETTHD target CPU load
FCCPUTHD ACCTHD AC control threshold
FCCPUTHD ACRTHD AC restore threshold
FCCPUTHD IURGCTHD Iur-g control threshold
FCCPUTHD IURGRTHD Iur-g restore threshold
Low Priority Service Control

FCCPUTHD LPRISERVCTHD Threshold
Low Priority Service Restore

FCCPUTHD LPRISERVRTHD Threshold
Normal Priority Service Control

FCCPUTHD NPRISERVCTHD Threshold
Normal Priority Service Restore

FCCPUTHD NPRISERVRTHD Threshold
High Priority Service Control
FCCPUTHD HPRISERVCTHD Threshold
High Priority Service Restore

FCCPUTHD HPRISERVRTHD Threshold
FCCPUTHD MRCTHD MR control threshold
FCCPUTHD MRRTHD MR restore threshold
FCMSGQTHD BRDCLASS Board Class
FCMSGQTHD SMWINDOW Filter window
FCMSGQTHD CTHD Critical threshold
FCMSGQTHD PRINTCTHD Print control threshold
FCMSGQTHD PRINTRTHD Print restore threshold
FCMSGQTHD TRACECTHD Debug tracking control threshold
FCMSGQTHD TRACERTHD Debug tracking restore threshold

Performance monitor control
FCMSGQTHD PMCTHD threshold
Performance monitor restore
FCMSGQTHD PMRTHD threshold
FCMSGQTHD RESAUDITCTHD Resource Audit control threshold
FCMSGQTHD RESAUDITRTHD Resource Audit restore threshold
FCMSGQTHD PAGECTHD Paging control threshold
FCMSGQTHD PAGERTHD Paging restore threshold
FCMSGQTHD HANDOVERCTHD Handover control threshold
FCMSGQTHD HANDOVERRTHD Handover restore threshold
FCMSGQTHD IURULCTHD Iur uplink transfer control threshold
FCMSGQTHD IURULRTHD Iur uplink transfer restore threshold

Iur downlink transfer control
FCMSGQTHD IURDLCTHD threshold
Iur downlink transfer restore
FCMSGQTHD IURDLRTHD threshold
FCMSGQTHD CBSCTHD CBS control threshold

FCMSGQTHD CBSRTHD CBS restore threshold
FCMSGQTHD LOGCTHD Log control threshold
FCMSGQTHD LOGRTHD Log restore threshold
FCMSGQTHD CELLURACTHD Cell URA update control threshold
FCMSGQTHD CELLURARTHD Cell URA update restore threshold
FCMSGQTHD ACCTHD AC control threshold
FCMSGQTHD ACRTHD AC restore threshold
FCMSGQTHD IURGCTHD Iur-g control threshold
FCMSGQTHD IURGRTHD Iur-g restore threshold
FCSW BRDCLASS Board Class
FCSW FCSW Flow control switch
FCSW PRINTSW Print Flow control switch
FCSW TRACESW Debug Flow control switch

Performance monitoring flow
FCSW PMSW control switch
FCSW RESAUDITSW Resource audit flow control switch
FCSW PAGESW Paging flow control switch
FCSW HANDOVERSW Handover flow control switch

Iur uplink transfer flow control
FCSW IURULSW switch
Iur downlink transfer flow control
FCSW IURDLSW switch
FCSW CBSSW CBS flow control switch
FCSW LOGSW Log control switch

Cell URA update flow control
FCSW CELLURASW switch
FCSW IUCTHD IU max call barring ratio
FCSW ACSW AC control switch
FCSW IUFCSW IU flow control switch

FCSW IURGSW Iur-g flow control switch
FCSW MRFCSW MR control switch
FRALNK SRN Subrack No.
FRALNK SN Slot No.
FRALNK FRALNKN Fractional link No.
FRALNK E1T1PN Bearing port No.
FRALNK TSBITMAP Bearing time slot
FRALNK FRALNKT Fractional link type
FRALNK IMAGRPN IMA group No.
FRALNK FLOWCTRLSWITCH Flow control switch
FRALNK FCINDEX Flow control parameter index
FRALNK TRMLOADTHINDEX TRM load threshold index
FRALNK OPSEPFLAG Operator Separated Flag
FRALNK OPSEPINDEX Operator Separated Index
FTPCLTPORT STARTPORT Start Data Port
FTPCLTPORT ENDPORT End Data Port
FTPPWD NEW New Password
FTPPWD CFM Confirm Password

FTPSCLT ENCRYMODE The Encrypted Mode
FTPSCLT SPTSTATEFWL Support State Firewall
FTPSCLTDPORT ServerIP FTP Server IP Address
FTPSCLTDPORT Port Destination Port
FTPSRVPORT STARTPORT Start Data Port
FTPSRVPORT ENDPORT End Data Port
FTPSSRV ENCRYMODE Transport Encrypted Mode
The Type of FTP Server

FTPSSRV DFTPORTSWT Command Port
FTPSSRV SERCMDPORT The Command Port of FTP Server

The Source Date Port of FTP
FTPSSRV SERDATAPORT Server
GLOBALROUTESW GLOBALROUTESW Global route management switch
GPS AGPSRECEIVERID GPS ID
GPS AGPSRECEIVERTYPE GPS type
GPS RNCID RNC ID
GPS CellId Cell ID
GPS GPSPERIOD GPS data report period
GPS DGPSPERIOD DGPS data report period[min]
GPS GCDF GCDF

GPS MTRLGY Metrology
GPS LATITUDE GPS antenna latitude
GPS LONGITUDE GPS antenna longitude
GPS ALTITUDE GPS antenna altitude
GPS LATITUDESEC GPS antenna latitude
GPS LONGITUDESEC GPS antenna longitude
GPS ALTITUDEIMP GPS antenna altitude
GPS GPSPERIOD GPS data report period
GPS DGPSPERIOD DGPS data report period[min]
ICMPGUARD SRN Subrack No.
ICMPGUARD SN Slot No.
ICMPGUARD IPADDR Packet source IP address
ICMPGUARD MASK Packet source mask
ICMPGUARD GUARDTYPE ICMP type which will be guarded
IMAGRP SRN Subrack No.
IMAGRP SN Slot No.
IMAGRP BT Board Type
IMAGRP IMAGRPN IMA group No.

IMAGRP MINLNKNUM Min Number of Links Activated
IMAGRP IMAID IMA ID
IMAGRP FRMLEN TX frame length
IMAGRP DELAY Max diff delay[ms]
IMAGRP IMAVER IMA protocol version
IMAGRP FLOWCTRLSWITCH Flow control switch
IMAGRP FCINDEX Flow control parameter index

Expected diff delay guard-
IMAGRP DLYGB band[cells]
IMAGRP TRMLOADTHINDEX TRM load threshold index
IMAGRP OPSEPFLAG Operator Separated Flag
IMAGRP OPSEPINDEX Operator Separated Index
IMALNK SRN Subrack No.
IMALNK SN Slot No.
IMALNK IMALNKN IMA link No.

IMALNK IMAGRPSN IMA Group Slot No.
IMALNK IMAGRPN IMA group No.
INFBRDRESCFG RESTYPE Restoring Type

INFBRDRESCFG IURESSW Recovery Switch
INFBRDRESCFG IUBRESSW Recovery Switch
INFBRDRESCFG RESSW Recovery Switch

NOBACKUPRESETCELLFAULTR Cell Faulty Rate Of Stand-alone
INFBRDRESCFG ATE Board For Reset
NOBACKUPRESETFAULTNODE Faulty NodeB Number On Stand-
INFBRDRESCFG BNUM alone Board For Reset
BACKUPRESETCELLFAULTRAT Port Cell Faulty Rate Of
INFBRDRESCFG E Main/Standby Board For Reset
BACKUPRESETFAULTNODEBN Port Faulty NodeB Number On
INFBRDRESCFG UM Main/Standby Board For Reset
INFBRDRESCFG BRDREQTIMES Exchange/Establish Requests

Number of SPU To PIU
INFBRDRESCFG SUBSYSREQTIMES Exchange/Establish Requests
Timeout/Failure Rate of SPU
INFBRDRESCFG REQTIMEOUTRATE Exchange/Establish Requests
INFBRDRESCFG QUERYPERIOD Query Period
INFBRDRESCFG QUERYTIMES Number of Queries

Number of Subsequent Fault
INFBRDRESCFG CONTINUOUSFAULTTIMES States For Reset
MERELOADCONTINUOUSFAULT Number of Subsequent Fault
INFBRDRESCFG TIMES States For ME Reload
INFBRDRESCFG RESTIMESPERDAY Number of Recoveries Per Day
INFBRDRESCFG LOGSW Verbose Logging Switch

STATISTICUOIPLOOPFAULTTIM UOIP Signaling Plane Loopback
INFBRDRESCFG E Test Result Statistic Duration
Cell Faulty Rate of One Port For
INFBRDRESCFG CELLFAULTRATEPERPORT ME Reload
IPGUARD SRN Subrack No.
IPGUARD SN Slot No.
IPGUARD BRDTYPE Board type.

IPGUARD VALIDPKTCHKSW Invalid Packet Check Switch
Invalid Packet Alarm

IPGUARD INVALIDPKTALMTHD Threshold[packet/s]
Invalid Packet Alarm Clearance

IPGUARD INVALIDPKTALMRTHD Threshold[packet/s]
IPGUARD ARPLRNSTRICTSW ARP Learning Strict Switch
IPLOGICPORT SRN Subrack No.
IPLOGICPORT SN Slot No.
IPLOGICPORT BT Board Type
IPLOGICPORT LPNTYPE Type of the logic port
IPLOGICPORT LPN Logic Port No.
IPLOGICPORT CARRYT The bearing type of the logic port
IPLOGICPORT PN Physical port No.
IPLOGICPORT UPPERLP The Upper logic port number
IPLOGICPORT TRUNKN The Trunk group No.
IPLOGICPORT PPPLNKN PPP link No.
IPLOGICPORT MPGRPN MP Group No.

IPLOGICPORT RSCMNGMODE Resource management mode
IPLOGICPORT CNOPINDEX CN operator index
IPLOGICPORT BWADJ Auto adjust bandwidth switch
IPLOGICPORT MAXBW Max bandwidth [64kbps]
IPLOGICPORT MINBW Min bandwidth [64kbps]

Load Control algorithm BandWidth
IPLOGICPORT BWRTPTH THD[%]
IPLOGICPORT CIR Bandwidth [64kbps]
IPLOGICPORT CBS Consent burst size [Byte]
IPLOGICPORT OAMFLOWBW OAM flow min bandwidth[%]
IPLOGICPORT RDC Rate down coefficient [%]
IPLOGICPORT RUS Rate up step [kbps]

Packet lost measure period
IPLOGICPORT PLPRD [100ms]
Rate up step adjust period
IPLOGICPORT RUSPRD [PLPRD]
IPLOGICPORT BWMAXRATIO Max bandwidth estimate ratio [%]
IPLOGICPORT PLTH Packet discard threshold[0.001]
IPLOGICPORT LATPRD Delay measure period [100ms]
IPLOGICPORT LATTH Rate down threshold for delay [ms]

Suspend times after bandwidth
IPLOGICPORT LOSTSUSTM adjusted
Delay adjust suspend period
IPLOGICPORT LATSUSTM [LATTH]
IPLOGICPORT LATUPK Average delay up filter mantissa
IPLOGICPORT LATUDK Average delay down filter mantissa
IPLOGICPORT FLOWCTRLSWITCH Flow control switch
IPLOGICPORT FCINDEX Flow control parameter index

Decrease rate alarm report
IPLOGICPORT RPTTHD threshold
Decrease rate alarm recover
IPLOGICPORT RECOVERTHD threshold
IPLOGICPORT TRMLOADTHINDEX TRM load threshold index
IPLOGICPORT OPSEPFLAG Operator Separated Flag
IPLOGICPORT OPSEPINDEX Operator Separated Index
IPMUX MUXTYPE IP MUX Type
IPMUX ANI Adjacent node ID
IPMUX PATHID IP path ID
IPMUX ISQOSPATH IS QOSPATH
IPMUX PHB PHB
IPMUX SUBFRAMELEN Max subframe length[byte]
IPMUX MAXFRAMELEN Maximum Frame Length[byte]
IPMUX FPTIMER Maximum Delay Time[ms]
IPMUX UDPMUXMODSEND Sender UDP MUX Mode
IPMUX UDPMUXMODRECV Receive UDP MUX Mode
IPMUX IPMUXINDEX IP MUX Index
IPMUX MUXTYPE IP MUX Type
IPOAPVC IPADDR IP address
IPOAPVC PEERIPADDR Peer IP address

IPOAPVC CARRYT Bearing type
IPOAPVC CARRYSN Bearing slot No.
IPOAPVC CARRYIMAGRPN Bearing IMA group No.
IPOAPVC CARRYUNILNKN Bearing UNI link No.
IPOAPVC CARRYFRAATMLNKN Bearing FRAATM link No.
IPOAPVC CARRYNCOPTN Bearing NCOPT port No.
IPOAPVC CARRYVPN Bearing ATM logic port No.
IPOAPVC CARRYVPI Bearing VPI
IPOAPVC CARRYVCI Bearing VCI
IPOAPVC TXTRFX TX traffic record index
IPOAPVC RXTRFX RX traffic record index
IPOAPVC PEERT Peer type
IPPATH ANI Adjacent Node ID
IPPATH PATHID IP path ID

IPPATH ITFT Interface Type
IPPATH TRANST Transport Type
IPPATH PATHT IP path type
IPPATH IPADDR Local IP address
IPPATH PEERIPADDR Peer IP address
IPPATH PEERMASK Peer subnet mask
IPPATH TXBW Forward Bandwidth
IPPATH RXBW Backward Bandwidth

IPPATH CARRYFLAG Carry Flag
IPPATH LPNSN IP Logic Port Slot No.
IPPATH LPN IP Logic Port No.
IPPATH RSCGRPN Rscgrp No.
IPPATH TRMLOADTHINDEX TRM load threshold index
IPPATH VLANFlAG VLANID Flag
IPPATH VLANID VLAN ID.
IPPATH PATHCHK IP path check flag
IPPATH ECHOIP Check IP address
IPPATH PERIOD Ping Check Period
IPPATH CHECKCOUNT Ping Check Timeout Counts
IPPATH ICMPPKGLEN Ping packet Length
IPPATH CHECKT IP path check type
IPPATHBIND ANI Adjacent node ID
IPPATHBIND PATHID IP path ID
IPPATHBIND SRN Subrack No.
IPPATHBIND SN Slot No.

IPPATHBIND CHKN Check Index
IPRT SRN Subrack No.
IPRT SN Slot No.
IPRT DSTIP Destination IP address
IPRT DSTMASK Destination address mask
IPRT NEXTHOP Forward route address
IPRT PRIORITY Priority
IPRT REMARK Purpose description
IPRT DSTMASK Destination address mask
IPRTBIND SRN Subrack No.
IPRTBIND SN Slot No.
IPRTBIND DESTIP Destination IP address
IPRTBIND MASK Subnet mask
IPRTBIND NEXTHOP Forward route address
IPRTBIND MBFDCHKN MBFD Check Index

JTGCPLD SRN Subrack No.
JTGCPLD SN Slot No.
JTGCPLD OPMODE Operate mode
JTGCPLD DATAFILE Data file
JTGCPLD RSTDESFILE Reset file
LICALMTHD LICALMCTHD Alarm occur threshold
LICALMTHD LICALMRTHD Alarm recover threshold
LICENSE SETOBJECT Set Object License
LICENSE ISPRIMARYPLMN Primary Operator Flag
LICENSE CNOPERATORINDEX Cn Operator Index
LICENSE CsErlang Voice Erlang-Erlang
LICENSE Psthroughput PS throughput only-kbps
LICENSE HSDPAthroughput HSDPA Throughput-kbps
LICENSE HSUPAthroughput HSUPA Throughput-kbps
LICENSE MBMSthroughput MBMS Throughput-kbps

Hardware Capacity License-
LICENSE HardwareCapacity 165Mbps per board
Fast Dormancy Enhancement-per
LICENSE FastDormancyEnhancement PS Active User
Hardware Capacity License-
LICENSE HardwareCapacityEx 300Mbps per board
LICENSE PSActiveUsers PS Active Users

Push To Talk (per PTT Active
LICENSE PushToTalk User)
LICENSE FUNCTIONSWITCH1 Function Switch1

LICENSE FN File Name
LICENSECTRL SWITCH Grace Protection Period Switch
Path Load EQ Threshold Table

LOADEQ LEI Index
LOADEQ REMARK Remark
Common Channel Pri Path Load

LOADEQ CCHPRITH Threshold
Common Channel Sec-Pri Path

LOADEQ CCHSECWHT Load Ratio Threshold
IMS Signal Pri Path Load
LOADEQ SIPPRITH Threshold
IMS Signal Sec-Pri Path Load

LOADEQ SIPSECWHT Ratio Threshold
LOADEQ SRBPRITH Signal Pri Path Load Threshold
Signal Sec-Pri Path Load Ratio

LOADEQ SRBSECWHT Threshold
AMR Voice Pri Path Load

LOADEQ VOICEPRITH Threshold
AMR Voice Sec-Pri Path Load

LOADEQ VOICESECWHT Ratio Threshold
R99 CS Conversational Pri Path

LOADEQ CSCONVPRITH Load Threshold
R99 CS Conversational Sec-Pri

LOADEQ CSCONVSECWHT Path Load Ratio Threshold
R99 CS Streaming Pri Path Load

LOADEQ CSSTRMPRITH Threshold
R99 CS Streaming Sec-Pri Path

LOADEQ CSSTRMSECWHT Load Ratio Threshold
R99 PS Conversational Pri Path

LOADEQ PSCONVPRITH Load Threshold
R99 PS Conversational Sec-Pri

LOADEQ PSCONVSECWHT Path Load Ratio Threshold
R99 PS Streaming Pri Path Load
LOADEQ PSSTRMPRITH Threshold
R99 PS Streaming Sec-Pri Path

LOADEQ PSSTRMSECWHT Load Ratio Threshold
R99 PS High Interactive Pri Path

LOADEQ PSHIGHINTERACTPRITH Load Threshold
R99 PS High Interactive Sec-Pri

LOADEQ PSHIGHINTERACTSECWHT Path Load Ratio Threshold
R99 PS Mid Interactive Pri Path

LOADEQ PSMIDINTERACTPRITH Load Threshold
R99 PS Mid Sec-Pri Path Load

LOADEQ PSMIDINTERACTSECWHT Ratio Threshold
R99 PS Low Interactive Pri Path

LOADEQ PSLOWINTERACTPRITH Load Threshold
R99 PS Low Interactive Sec-Pri

LOADEQ PSLOWINTERACTSECWHT Path Load Ratio Threshold
R99 PS Background Pri Path Load

LOADEQ PSBKGPRITH Threshold
R99 PS Background Sec-Pri Path

LOADEQ PSBKGSECWHT Load Ratio Threshold
HSDPA Signal Pri Path Load

LOADEQ HDSRBPRITH Threshold
HSDPA Signal Sec-Pri Path Load

LOADEQ HDSRBSECWHT Ratio Threshold
HSDPA IMS Signal Pri Path Load
LOADEQ HDSIPPRITH Threshold
HSDPA IMS Signal Sec-Pri Path

LOADEQ HDSIPSECWHT Load Ratio Threshold
HSDPA Conversational Pri Path

LOADEQ HDCONVPRITH Load Threshold
HSDPA Conversational Sec-Pri

LOADEQ HDCONVSECWHT Path Load Ratio Threshold
HSDPA Streaming Pri Path Load

LOADEQ HDSTRMPRITH Threshold
HSDPA Streaming Sec-Pri Path

LOADEQ HDSTRMSECWHT Load Ratio Threshold
HSDPA High Interactive Pri Path

LOADEQ HDHIGHINTERACTPRITH Load Threshold
HSDPA High Sec-Pri Path Load

LOADEQ HDHIGHINTERACTSECWHT Ratio Threshold
HSDPA Mid Interactive Pri Path

LOADEQ HDMIDINTERACTPRITH Load Threshold
HSDPA Mid Interactive Sec-Pri

LOADEQ HDMIDINTERACTSECWHT Path Load Ratio Threshold
HSDPA Low Interactive Pri Path

LOADEQ HDLOWINTERACTPRITH Load Threshold
HSDPA Low Interactive Sec-Pri

LOADEQ HDLOWINTERACTSECWHT Path Load Ratio Threshold
HSDPA Background Pri Path Load
LOADEQ HDBKGPRITH Threshold
HSDPA Background Sec-Pri Path

LOADEQ HDBKGSECWHT Load Ratio Threshold
HSUPA Signal Pri Path Load

LOADEQ HUSRBPRITH Threshold
HSUPA Signal Sec-Pri Path Load

LOADEQ HUSRBSECWHT Ratio Threshold
HSUPA IMS Signal Pri Path Load

LOADEQ HUSIPPRITH Threshold
HSUPA IMS Signal Sec-Pri Path

LOADEQ HUSIPSECWHT Load Ratio Threshold
HSUPA Conversational Pri Path

LOADEQ HUCONVPRITH Load Threshold
HSUPA Conversational Sec-Pri

LOADEQ HUCONVSECWHT Path Load Ratio Threshold
HSUPA Streaming Pri Path Load

LOADEQ HUSTRMPRITH Threshold
HSUPA Streaming Sec-Pri Path

LOADEQ HUSTRMSECWHT Load Ratio Threshold
HSUPA High Interactive Pri Path

LOADEQ HUHIGHINTERACTPRITH Load Threshold
HSUPA High Interactive Sec-Pri

LOADEQ HUHIGHINTERACTSECWHT Path Load Ratio Threshold
HSUPA Mid Interactive Pri Path
LOADEQ HUMIDINTERACTPRITH Load Threshold
HSUPA Mid Interactive Sec-Pri

LOADEQ HUMIDINTERACTSECWHT Path Load Ratio Threshold
HSUPA Low Interactive Pri Path

LOADEQ HULOWINTERACTPRITH Load Threshold
HSUPA Low Interactive Sec-Pri

LOADEQ HULOWINTERACTSECWHT Path Load Ratio Threshold
HSUPA Background Pri Path Load

LOADEQ HUBKGPRITH Threshold
HSUPA Background Sec-Pri Path

LOADEQ HUBKGSECWHT Load Ratio Threshold
Primary Path Realtime Load

LOADEQ RTPRITH Threshold
Sec-Pri Path Realtime Load Ratio

LOADEQ RTSECWHT Threshold
LODCTRL LODCTRL Board Start Load Control
LOGCFG MODULE MODULE NAME
LOGCFG FWFLAG Flow Log Flag
LOGCFG FRMFLAG Frame Log Flag
LOGCFG FILTERKEY Filter Type Of Frame Log
LOGCFG TASKID TaskID
LOGCFG CMDCODE Command Code

LOGLIMIT TL Time Limit
LOGLIMIT CNTL Counts Limit
LOGLIMIT LT Log Type
M3DE DENO Destination entity No.
M3DE LENO Local entity No.
M3DE DPX DSP index
M3DE ENTITYT Destination entity type
M3DE RTCONTEXT Routing Context
M3DE NAME Destination entity name
M3LE LENO Local entity No.
M3LE SPX OSP index
M3LE ENTITYT Local entity type
M3LE RTCONTEXT Routing Context
M3LE NAME Local entity name
M3LKS SIGLKSX Signalling link set index
M3LKS DENO Destination entity No.
M3LKS LNKSLSMASK Signalling link mask
M3LKS TRAMODE Traffic mode

M3LKS WKMODE Work mode
M3LKS PDTMRVALUE PENDING timer
M3LKS NAME M3UA Signalling link set name
M3LNK SIGLKSX Signalling link set index
M3LNK SIGLNKID Signaling link ID
M3LNK SRN Subrack No.
M3LNK SN Slot No.

M3LNK SSN Subsystem No.
M3LNK SCTPLNKN SCTP link No.
M3LNK PRIORITY Signalling link priority
M3LNK LNKREDFLAG Initial bearing traffic active tag
M3LNK NAME M3UA Signaling link name
M3RT DENO Destination entity No.
M3RT SIGLKSX Signalling link set index
M3RT PRIORITY Route priority
M3RT NAME M3UA route name
MEASRSTLIMIT RT Measure Result Type
MEASRSTLIMIT TL Result Time Limit
MEASRSTLIMIT SL Result Space Limit
MPGRP SRN Subrack No.
MPGRP SN Slot No.

MPGRP BRDTYPE Board type
MPGRP LGCAPPTYPE Logic function type
MPGRP MPGRPN MP Group No.
MPGRP MPTYPE MP type
MPGRP BORROWDEVIP Borrow DevIP
MPGRP LOCALIP Local IP address
MPGRP DEVIP Borrowed device IP address
MPGRP MASK Subnet mask
MPGRP PEERIP Peer IP address
MPGRP MHF MP/MC list head option
MPGRP MCCLASS MC PRI number

MPGRP FRAGSIZE MP flake size
MPGRP IPHC Head compress
MPGRP PFC Protocol field compress
Address and control field

MPGRP ACFC compress
MPGRP PPPMUX PPP mux
MPGRP MAXSFLEN PPP mux max sub-frame length
MPGRP MAXMFLEN PPP mux max mux-frame length

MPGRP MUXTIME PPP mux framing out-time[us]
MPGRP FLOWCTRLSWITCH Flow control switch
MPGRP FCINDEX Flow control parameter index
MPGRP OAMFLOWBW OAM flow min bandwidth[%]
MPGRP AUTHTYPE Validate protocol type
MPGRP AUTHMODE Validate mode
MPGRP AUTHNAME Validate user name
MPGRP AUTHPWD Validate password
MPGRP TRMLOADTHINDEX TRM load threshold index
MPGRP ERRDETECTSW Error-frame detect switch
MPGRP ERRALARMTHD Error-frame alarm threshold
MPGRP ANTIERRFLAG E1T1 anti-error switch
MPGRP EMITTHD Error emit threshold

MPGRP CLEARTHD Error clear threshold
MPGRP OPSEPFLAG Operator Separated Flag
MPGRP OPSEPINDEX Operator Separated Index
MPGRP MCCLASS MC PRI number
MPGRP MAXSFLEN PPP mux max sub-frame length
MPGRP MAXMFLEN PPP mux max mux-frame length
MPGRP MUXTIME PPP mux framing out-time[us]
MPGRP EMITTHD Error emit threshold

MPGRP CLEARTHD Error clear threshold
MPLNK SRN Subrack No.
MPLNK SN Slot No.
MPLNK BRDTYPE Board type
MPLNK MPGRPN MP Group No.
MPLNK PPPLNKN PPP sub-link No.
MPLNK DS1 E1T1 port No.
MPLNK TSBITMAP Bearing time slot
MPLNK RESTARTTMR Sub-protocol negotiate out time[S]
MPLNK KEEPALIVE Keep-alive timer length[S]

MPLNK FCSTYPE CRC check mode
MPUBIND SRN Subrack No.
MPUBIND SN Slot No.
MPUBIND MPUSUBRACK MPU Subrack No.
MPUBIND MPUSLOT MPU Slot No.
MSP SRN Subrack No.
MSP SN Slot No.
MSP PN Port No.
MSP RT Revertive type
MSP WTRT WTR Time[Sec]
MSP K2MODE K2 Mode
MSP SDENABLE SD Enable
MSP SDALMTHD SD Alarm Threshold
MSP SDSFPRI SDSF Priority
MSP MODE Backup mode
MSPCMD SRN Subrack No.
MSPCMD SN Slot No.
MSPCMD PN Port No.

MSPCMD MSPCMD MSP Control Command
MTP3LKS SIGLKSX Signalling link set index
MTP3LKS DPX DSP index
MTP3LKS LNKSLSMASK Signalling link mask
MTP3LKS EMERGENCY Emergency verification
MTP3LKS NAME Signalling link set name
MTP3LNK SIGLKSX Signalling link set index
MTP3LNK SIGSLC Signalling link code
MTP3LNK SRN Subrack No.
MTP3LNK SN Slot No.
MTP3LNK SAALLNKN SAAL link No.
MTP3LNK PRIORITY Signalling link priority
MTP3LNK TCLEN Test code length
MTP3LNK TC Test code
MTP3LNK NAME Signalling link name
MTP3RT DPX DSP index
MTP3RT SIGLKSX Signalling link set index

MTP3RT PRIORITY Route priority
MTP3RT NAME Signalling Route name
MTP3TMR T1TMR Time-control changeover timer
MTP3TMR T2TMR Changeover ACK timer
MTP3TMR T3TMR Time-control changeback timer

Changeover ACK first attempt
MTP3TMR T4TMR timer
Changeover ACK second attempt
MTP3TMR T5TMR timer
Transmission prohibited inhibition
MTP3TMR T8TMR timer
MTP3TMR T10TMR Signalling route set test timer
MTP3TMR T12TMR Uninhibit ACK timer
MTP3TMR T13TMR Force uninhibit timer
MTP3TMR T14TMR Inhibition ACK timer
MTP3TMR T17TMR Link realignment timer
MTP3TMR T22TMR Local inhibit test timer
MTP3TMR T23TMR Remote inhibit test timer
MTP3TMR TMT1TMR Signalling link test ACK timer
MTP3TMR TMT2TMR Signalling link repeat test timer
MTP3TMR SAALTMR L2 link connection timer
N7DPC NAME DSP name
N7DPC DPX DSP index
N7DPC SPX OSP index

N7DPC SPDF Signal point data format
N7DPC DPC DSP code[Whole Number]
N7DPC DPCDNF DSP code[Divided Number]
N7DPC DPCT DSP type
N7DPC SLSMASK Signalling route mask
N7DPC NEIGHBOR Adjacent flag
N7DPC STP STP function switch
N7DPC BEARTYPE DSP bear type
N7DPC NETPRI Net PRI
N7DPC PROT SS7 protocol type
OBJALMSHLD OBJTP Object Type
OBJALMSHLD SRN Subrack No.
OBJALMSHLD SN Slot No.
OBJALMSHLD PN Port No.
OBJALMSHLD DSPN DSP No.

OBJALMSHLD AIDST Alarm Select Type
OBJALMSHLD AID Alarm ID
OFFICENAME SID Office Name
OMUIPRT RTDEST Destination Network Address
OMUIPRT RTDESTMASK Destination Address Mask
OMUIPRT NEXTHOP Forward Route Address
OP OP Operator
OP DESC Description
OP PWD Password
OP CFM Confirm Password
OP UG Operator Level
OP CG Command Group
OP DATE Date Limit
OP STD Start Date
OP ETD End Date
OP TIME Time Limit
OP STT Start Time
OP ETT End Time
OP WEEK Week Limit
OP WK Week
OP NEW New Password
OP UG Operator Level
OP TIME Time Limit
OP WEEK Week Limit
OPC NAME OSP name
OPC SPX OSP index
OPC NI Network ID
OPC SPCBITS OSP code bits
OPC SPDF Signal point data format
OPC SPC OSP code[Whole Number]
OPC SPCDNF OSP code[Divided Number]
OPC RSTFUN Restart switch
OPLOCK LOCKST Set Locked/Unlock

Index of Separate Information for
OPSEPINFO OPSEPINDEX Operators
the Count of the Operators
OPSEPINFO OPCOUNT Selected
OPSEPINFO TYPE Transport Type
OPSEPINFO OPTYPE The type of operator
OPSEPINFO OPINDEX1 Index of 1st Operator
OPSEPINFO BWRATIO1 Bandwidth Ratio of 1st Operator
OPSEPINFO TRMLOADTHINDEX1 Load Threshold of 1st Operator

OPSEPINFO OPINDEX2 Index of 2nd Operator
OPSEPINFO BWRATIO2 Bandwidth Ratio of 2nd Operator
OPSEPINFO TRMLOADTHINDEX2 Load Threshold of 2nd Operator
OPSEPINFO OPINDEX3 Index of 3rd Operator
OPSEPINFO BWRATIO3 Bandwidth Ratio of 3rd Operator
OPSEPINFO TRMLOADTHINDEX3 Load Threshold of 3rd Operator
OPSEPINFO OPINDEX4 Index of 4th Operator
OPSEPINFO BWRATIO4 Bandwidth Ratio of 4th Operator
OPSEPINFO TRMLOADTHINDEX4 Load Threshold of 4th Operator
OPSW SWOP Set Enable/Disable
OPT SRN Subrack No.
OPT SN Slot No.
OPT BT Board type
OPT PS Port select
OPT PN Port No.
OPT SCRAMBLESW Scramble switch
OPT OPTM Optical interface standard
OPT LNKNUMMODE Tributary Numbering
OPT WORKTYPE Work Type
OPT J0TYPE J0 type
OPT J0BYTE_FORMAT J0 Byte Format
OPT J0TXT J0 transmit type

OPT J0TXBYTE_FORMAT J0 Transmit Format
OPT J0TXVALUE J0 transmit value
OPT J0RXT J0 expected incept type
OPT J0RXBYTE_FORMAT J0 Expected Incept Format
OPT J0RXVALUE J0 expected incept value
OPT J1TYPE J1 type
OPT J1BYTE_FORMAT J1 Byte Format
OPT J1TXT J1 transmit type
OPT J1TXBYTE_FORMAT J1 Transmit Format
OPT J1TXVALUE J1 transmit value
OPT J1RXT J1 expected incept type
OPT J1RXBYTE_FORMAT J1 Expected Incept Format
OPT J1RXVALUE J1 expected incept value
OPT S1VALUE S1 Value
OPT B1B2SFTHRD B1B2 signal fail threshold

OPT B1B2SDTHRD B1B2 signal degraded threshold
OPT B3SFTHRD B3 signal fail threshold
OPT B3SDTHRD B3 signal degraded threshold
OPT FLOWCTRLSWITCH Flow control switch
OPT FCINDEX Flow control parameter index
OPT JAUTOADD Automatic Append J Byte
OPT AUTYPE Administration unit type
OPTLOP SRN Subrack No.
OPTLOP SN Slot No.

OPTLOP PN Port No.
OPTLOP LOPT Loop type.
PATCH OT Operation type
PATCH BT Board type
PATCH LGCAPPTYPE Logical function type
PATCH PATTYPE Patch type
PHBMAP SRN Subrack No.
PHBMAP SN Slot No
PHBMAP PHB Per-Hop Behavior
PHBMAP DSCP Differentiated Service Codepoint
PORTFLOWCTRLPARA FCINDEX Flow control parameter index
PORTFLOWCTRLPARA PORTPROTYPE Port protocol type
PORTFLOWCTRLPARA PQNUM Priority queue number
Congestion threshold of queue 0

PORTFLOWCTRLPARA CONGTHD0 [ms]
PORTFLOWCTRLPARA CONGCLRTHD0 Recover threshold of queue 0 [ms]
Packet discard threshold of queue

PORTFLOWCTRLPARA DROPPKTTHD0 0 [ms]










PPPLNK SRN Subrack No.
PPPLNK SN Slot No.
PPPLNK BRDTYPE Board type
PPPLNK LGCAPPTYPE Logic function type
PPPLNK PPPLNKN PPP link No.
PPPLNK DS1 E1T1 port No.

PPPLNK TSBITMAP Bearing time slot
PPPLNK BORROWDEVIP Borrow DevIP
PPPLNK LOCALIP Local IP address
PPPLNK DEVIP Borrowed device IP address
PPPLNK MASK Subnet mask
PPPLNK PEERIP Peer IP address
PPPLNK IPHC Head compress
PPPLNK PFC Protocol field compress

Address and control field
PPPLNK ACFC compress
PPPLNK PPPMUX PPP mux
PPPLNK MAXSFLEN PPP mux max sub-frame length
PPPLNK MAXMFLEN PPP mux max mux-frame length
PPPLNK MUXTIME PPP mux framing out-time[us]
PPPLNK AUTHTYPE Validate protocol type
PPPLNK AUTHMODE Validate mode
PPPLNK AUTHNAME Validate user name
PPPLNK AUTHPWD Validate password
PPPLNK RESTARTTMR Sub-protocol negotiate out time[S]
PPPLNK KEEPALIVE Keep-alive timer length[S]

PPPLNK FLOWCTRLSWITCH Flow control switch
PPPLNK OAMFLOWBW OAM flow min bandwidth[%]
PPPLNK FCINDEX Flow control parameter index
PPPLNK FCSTYPE CRC check mode
PPPLNK TRMLOADTHINDEX TRM load threshold index
PPPLNK ERRDETECTSW Error-frame detect switch
PPPLNK ERRALARMTHD Error-frame alarm threshold
PPPLNK OPSEPFLAG Operator Separated Flag
PPPLNK OPSEPINDEX Operator Separated Index
PPPLNK PPPMUX PPP mux
PPPLNK MUXTIME PPP mux framing out-time[us]
PPPSELFLOOP SRN Subrack No.
PPPSELFLOOP SN Slot No.

PPPSELFLOOP LNKT Link type
PPPSELFLOOP MPGRPN MP Group No.

PPPSELFLOOP PPPLNKN PPP link No.
PPPSELFLOOP LOPT Loop type
PPPSELFLOOP AUSTOP Loop time[min]
PWDPOLICY PwdMinLen password minimal length
PWDPOLICY Complicacy password complicacy
PWDPOLICY MaxMissTimes password max miss times
PWDPOLICY AutoUnlockTime Auto Unlock Time

Resetting Interval of Account Lock
PWDPOLICY RESETINTERVAL Counter
PWDPOLICY MAXVALIDDATES Maximum Valid Days
PWDPOLICY MAXPROMPTDATES Expire Prompt Dates

Password History Records
PWDPOLICY HISTORYPWDNUM Number
Maximum Single Char Repeat
PWDPOLICY MaxRepeatCharTimes Times
First Login Must Modify Password
PWDPOLICY FirstLoginMustModPWD Switch
PWRALMSW SRN Subrack No.

PWRALMSW PWRALMSSW1 First Alarm Switch
PWRALMSW PWRALMSSW2 Second Alarm Switch
PWRPARA SRN Subrack No.
PWRPARA NO1M48ALMTHDUP Upper limit of No.1 input -48V[-V]
PWRPARA NO1M48ALMTHDDOWN Lower limit of No.1 input -48V[-V]

QUEUEMAP SRN Subrack No.
QUEUEMAP SN Slot No.
QUEUEMAP Q0MINDSCP Min DSCP of queue 0
QUEUEMAP OAMMINBWKEY OAM flow min bandwidth switch
QUEUEMAP OAMFLOWDSCP DSCP of OAM flow
QUICKCFG MODE Configure Mode
ROLLBACKPOINT POINTSELECT Remove Mode
ROLLBACKPOINT POINTNAME Rollback Point Name
ROLLBACKPOINT POINTDESINFO Rollback Point Description

ROOLBACK_YES CellId Cell ID
ROOLBACK_YES Ac09ToAsc AC 0~9 to ASC mapping
ROOLBACK_YES Ac10ToAsc AC 10 to ASC mapping
RSCGRP SRN Subrack No.
RSCGRP CTRLSLOT Slot No.
RSCGRP GRPID Transport Resource Group No.
RSCGRP GRPT Transport Resource Group Type
Is First Class Transport Resource

RSCGRP ISFIRSTCLASS Group
Upper Class Transport Resource

RSCGRP UPPERGRPID Group No.
RSCGRP RSCMNGMODE Resource Management Mode
RSCGRP CNOPINDEX CN Operator index
RSCGRP BWMODE Bandwidth Mode
RSCGRP TxBw Forward Bandwidth

RSCGRP RxBw Backward Bandwidth
RSCGRP AllBw Bandwidth
RSCGRP TRMLOADTHINDEX TRM load threshold index
SAALLNK SRN Subrack No.
SAALLNK SN Slot No.
SAALLNK SAALLNKN SAAL link No.
SAALLNK CARRYT Bearing type
SAALLNK CARRYSRN Bearing subrack No.
SAALLNK CARRYSN Bearing slot No.
SAALLNK CARRYUNILNKN Bearing UNI link No.
SAALLNK CARRYIMAGRPN Bearing IMA group No.
SAALLNK CARRYFRAATMLNKN Bearing FRAATM link No.
SAALLNK CARRYNCOPTN Bearing NCOPT port No.
SAALLNK CARRYVPN Bearing ATM logic port No.
SAALLNK CARRYVPI Bearing VPI
SAALLNK CARRYVCI Bearing VCI

SAALLNK TXTRFX TX traffic record index
SAALLNK RXTRFX RX traffic record index
SAALLNK SAALLNKT Interface type
SAALLNK MPS Management proving status
SAALLNK CCTMR Timer_CC
SAALLNK POLLTMR Timer_Poll
SAALLNK IDLETMR Timer_Idle
SAALLNK RSPTMR Timer_No-Response
SAALLNK KEEPTMR Timer_Keep-Alive
SAALLNK COMTMR1 Timer T1
SAALLNK SRECTMR Timer_REPEAT-SREC
SAALLNK INHTMR Timer_NO-CREDIT
SAALLNK MAXNRP Max_NRP
SAALLNK MAXCC MaxCC
SAALLNK MAXPD Max Poll Data Count

SAALLNK STATLEN MaxSTAT
SAALLNK N1 N1
SAALLNK WINDOWSIZE Receiving window size
SCCPTMR CONNECTTMR Connection establishment timer
SCCPTMR IATXTMR Inactive TX timer
SCCPTMR IARXTMR Inactive RX timer
SCCPTMR RELEASETMR Connection release timer
Repeated connection release

SCCPTMR REPRELEASETMR timer
SCCPTMR INTTMR Resource release timer
SCCPTMR GUARDTMR Guard timer
SCCPTMR RESETTMR Reset timer
SCCPTMR REASTMR Reassembly timer
SCCPTMR STATTMR Subsystem test timer
SCCPTMR COTMR Coordination timer
SCCPTMR IGNORTMR Subsystem test ignorance timer
SCCPTMR FREEZENTMR Resource frozen timer
SCCPTMR EATMR EA timer

SCCPTMR LRNTMR LRN frozen timer
SCHTSK ID Task ID
SCHTSK TSKN Task Name
SCHTSKSW ID Task ID
SCHTSKSW TSKN Task Name
SCHTSKSW ENF Status
SCPICH CellId Cell ID
SCPICH ScpichPhyId SCPICH ID
SCPICH ScpichPower SCPICH transmit power[0.1dB]
SCTPLNK SRN Subrack No.
SCTPLNK SN Slot No.
SCTPLNK SCTPLNKN SCTP link No.
SCTPLNK MODE Signalling link mode
SCTPLNK APP Application type
SCTPLNK DSCP Differentiated Service Codepoint
SCTPLNK LOCPN Local SCTP port No.

SCTPLNK LOCIP1 First local IP address
SCTPLNK LOCIP2 Second local IP address
SCTPLNK PEERIP1 First destination IP address
SCTPLNK PEERIP2 Second destination IP address
SCTPLNK PEERPN Destination SCTP port No.
SCTPLNK LOGPORTFLAG Logic Port Flag
SCTPLNK LOGPORTSN Logic Port Slot No.
SCTPLNK LOGPORTNO Logic Port No.
SCTPLNK RTOMIN RTO min value
SCTPLNK RTOMAX RTO max value
SCTPLNK RTOINIT RTO initial value
SCTPLNK RTOALPHA RTO alpha value

SCTPLNK RTOBETA RTO beta value
SCTPLNK TSACK SACK delay timer
SCTPLNK HBINTER Heartbeat interval
SCTPLNK MAXASSOCRETR Association max retrans
SCTPLNK MAXPATHRETR Path max retrans
Calculate checksum when send

SCTPLNK CHKSUMTX message
Calculate checksum when receive

SCTPLNK CHKSUMRX message
SCTPLNK CHKSUMTYPE Checksum arithmetic
SCTPLNK MTU MTU value

VLANID Flag of First Local IP
SCTPLNK VLANFLAG1 address
SCTPLNK VLANID1 VLAN ID of First Local IP address

VLANID Flag of Second Local IP
SCTPLNK VLANFlAG2 address
VLAN ID of Second Local IP

SCTPLNK VLANID2 address
SCTPLNK CROSSIPFLAG Cross IP address available flag
SCTPLNK SWITCHBACKFLAG Switch primary IP address flag
SCTPLNK SWITCHBACKHBNUM Switch back HB number
SCTPLNK BUNDLINGFLAG Bundling Flag
SCTPLNK HBINTER Heartbeat interval
SCTPLNK MAXASSOCRETR Association max retrans

SCTPLNK MAXPATHRETR Path max retrans
SCTPSRVPORT NBAPSRVPN NBAP service listening port No.
SCTPSRVPORT M3UASRVPN M3UA service listening port No.
SCTPSRVPORT BBAPSRVPN BBAP service listening port No.
SCUPORT SRN Subrack No.
SCUPORT SN Slot No.
SCUPORT PN Port No.
SCUPORT Switch Port switch
SHARETHD BT Board type

SMS RRC conn share CPU control
SHARETHD SMRRCCONNCCPUTHD threshold
SMS RRC conn share CPU
SHARETHD SMRRCCONNRCPUTHD restore threshold
Call RRC conn share CPU control
SHARETHD CRRCCONNCCPUTHD threshold
Call RRC conn share CPU restore
SHARETHD CRRCCONNRCPUTHD threshold
Location RRC conn share CPU
SHARETHD LRRCCONNCCPUTHD control threshold
Location RRC conn share CPU
SHARETHD LRRCCONNRCPUTHD restore threshold
SMS RRC conn share msg control
SHARETHD SMRRCCONNCMSGTHD threshold
SMS RRC conn share msg restore
SHARETHD SMRRCCONNRMSGTHD threshold
Call RRC conn share msg control
SHARETHD CRRCCONNCMSGTHD threshold
Call RRC conn share msg restore
SHARETHD CRRCCONNRMSGTHD threshold
Location RRC conn share msg
SHARETHD LRRCCONNCMSGTHD control threshold
Location RRC conn share msg
SHARETHD LRRCCONNRMSGTHD restore threshold
SLFSLVSW SWITCH Self-healing Switch

Self-healing Switch for OMU
SLFSLVSW PSW Process
Self-healing Switch for Memory
SLFSLVSW MSW Overload
Self-healing Switch for Ethernet
SLFSLVSW CSW Adapter Traffic Monitoring
SNTPCLTPARA SP Sync Period
SNTPSRVINFO IP IP Address
SNTPSRVINFO PT Port
SS7PATCHSWITCH SwitchParameter1 SwitchParameter1

SSLAUTHMODE AUTHMODE Authentication Mode
SUBCMD ID Task ID
SUBCMD TSKN Task Name
SUBCMD SUBID Subtask ID
SUBCMD SCMD Command String
SUBCMD CMDSEQ Command Sequence
SUBNET SUBNET Subnet No
SUBRACK SRN Subrack No.

SUBRACK SRName Subrack name
SUBRACK CONNPWR Connect power monitoring board
SUBRACK SCUTYPE SCU Type
SUBRACK SRTTYPE Subrack Hardware Type
SUBRACK SRN Subrack No.
SUBTSK ID Task ID
SUBTSK TSKN Task Name
SUBTSK SUBID Subtask ID
SUBTSK ENF Subtask Status
SUBTSK SCMD Command String
SUBTSK FREQ Time Mode
SUBTSK SD Start Date
SUBTSK ED End Date
SUBTSK RFT Execute Interval

SUBTSK DINM Date in Month
SUBTSK DINW Date in Week
SUBTSK TM1 Execute Time 1
SUBTSK ST Start Time
SUBTSK ET End Time
SUBTSK INTV Time Interval
SUBTSK TM Execute Time
SUBTSK ENF Subtask Status
SUBTSK SD Start Date
SUBTSK ED End Date
SUBTSK RFT Execute Interval

SUBTSK ST Start Time
SUBTSK ET End Time
SUBTSK INTV Time Interval
SUBTSK TM Execute Time
SYS SYSDESC System description
SYS SYSOBJECTID NE Name
SYS SYSCONTACT Contact mode of the manufacturer
SYS SYSLOCATION System Location
SYS SYSSERVICES System services
TGWIP TGWID TGW ID
TGWIP TGWIPOAMIP TGW IP_TRANS IP address
TGWIP TGWIPOAMMASK TGW IP_TRANS IP Mask
TGWIP TGWPEERSRN TGW Trans Subrack No.
TGWIP TGWPEERSN TGW TRANS Slot No.

TIME DATE Date
TIME TIME Time
TNSOFTPARA DiagnoseSCTPFault SCTP Fault Diagnosis Switch

SAAL Loopback Self-Healing
TNSOFTPARA SAALResumeByLoop Switch
SCTP Loopback Self-Healing
TNSOFTPARA SCTPResumeByLoop Switch
TNSOFTPARA SAALAutoTraceSwitch SAAL Auto Tracing Switch
TNSOFTPARA SCTPAutoTraceSwitch SCTP Auto Tracing Switch

FcSwicthByRatioBetweenCCAndC
TNSOFTPARA R CC/CR Flow Control Switch
CREF Congestion Flow Control
TNSOFTPARA CREFCongFc Switch
Interface Board Performance
TNSOFTPARA IntBrdPerfImprvSwitch Enhancing Switch
Interface Board Flow Control
TNSOFTPARA FcOnItfBrd Switch
SCTP Receive Flow Control
TNSOFTPARA SCTPRecvFc Switch
TRANSPATCHPARA SRN Subrack No.
TRANSPATCHPARA RSVDPARA1 Reserved Parameter 1


TRCTASK TASKNO task number
TRMFACTOR FTI Factor table index
TRMFACTOR REMARK Remark
UMTS general common channel

TRMFACTOR GENCCHDL service downlink factor
UMTS general common channel

TRMFACTOR GENCCHUL service uplink factor
UMTS IMS SRB service downlink
TRMFACTOR SIPDL factor
UMTS IMS SRB service uplink

TRMFACTOR SIPUL factor
UMTS MBMS common channel

TRMFACTOR MBMSCCHDL service downlink factor
UMTS SRB service downlink

TRMFACTOR SRBDL factor
TRMFACTOR SRBUL UMTS SRB service uplink factor

UMTS AMR voice service
TRMFACTOR VOICEDL downlink factor
UMTS AMR voice service uplink

TRMFACTOR VOICEUL factor
UMTS R99 CS conversational

TRMFACTOR CSCONVDL service downlink factor
UMTS R99 CS conversational

TRMFACTOR CSCONVUL service uplink factor
UMTS R99 CS streaming service

TRMFACTOR CSSTRMDL downlink factor
UMTS R99 CS streaming service
TRMFACTOR CSSTRMUL uplink factor
UMTS R99 PS conversational

TRMFACTOR PSCONVDL service downlink factor
UMTS R99 PS conversational

TRMFACTOR PSCONVUL service uplink factor
UMTS R99 PS streaming service

TRMFACTOR PSSTRMDL downlink factor
UMTS R99 PS streaming service

TRMFACTOR PSSTRMUL uplink factor
UMTS R99 PS interactive service
TRMFACTOR PSINTERDL downlink factor
UMTS R99 PS interactive service

TRMFACTOR PSINTERUL uplink factor
UMTS R99 PS background service

TRMFACTOR PSBKGDL downlink factor
UMTS R99 PS background service

TRMFACTOR PSBKGUL uplink factor
UMTS HSDPA signal downlink

TRMFACTOR HDSRBDL factor
UMTS HSDPA IMS signal
TRMFACTOR HDSIPDL downlink factor
UMTS HSDPA voice service

TRMFACTOR HDVOICEDL downlink factor
UMTS HSDPA conversational

TRMFACTOR HDCONVDL service downlink factor
UMTS HSDPA streaming service

TRMFACTOR HDSTRMDL downlink factor
UMTS HSDPA interactive service

TRMFACTOR HDINTERDL downlink factor
UMTS HSDPA background service

TRMFACTOR HDBKGDL downlink factor
TRMFACTOR HUSRBUL UMTS HSUPA signal uplink factor
UMTS HSUPA IMS signal uplink

TRMFACTOR HUSIPUL factor
UMTS HSUPA voice service uplink

TRMFACTOR HUVOICEUL factor
UMTS HSUPA conversational

TRMFACTOR HUCONVUL service uplink factor
UMTS HSUPA streaming service

TRMFACTOR HUSTRMUL uplink factor
UMTS HSUPA interactive service
TRMFACTOR HUINTERUL uplink factor
UMTS HSUPA background service

TRMFACTOR HUBKGUL uplink factor
UMTS EFACH channel forward

TRMFACTOR EFACHDL factor
UMTS EPCH channel forward

TRMFACTOR EPCHDL factor
UMTS ERACH channel uplink

TRMFACTOR ERACHUL factor
TRMLOADTH TRMLOADTHINDEX TRM load threshold index

TRMLOADTH TRANST Transport Type
TRMLOADTH THTYPE Threshold type
Forward handover reserved

TRMLOADTH FWDRSVHOBW bandwidth
Backward handover reserved

TRMLOADTH BWDRSVHOBW bandwidth
Forward congestion remain

TRMLOADTH FWDCONGBW bandwidth
Backward congestion remain

TRMLOADTH BWDCONGBW bandwidth
Forward congestion clear remain

TRMLOADTH FWDCONGCLRBW bandwidth
Backward congestion clear remain

TRMLOADTH BWDCONGCLRBW bandwidth
Forward overload congestion

TRMLOADTH FWDOVLDRSVBW remain bandwidth
Backward overload congestion

TRMLOADTH BWDOVLDRSVBW remain bandwidth
Forward overload congestion clear

TRMLOADTH FWDOVLDCLRRSVBW remain bandwidth
TRMLOADTH BWDOVLDCLRRSVBW clear remain bandwidth
TRMLOADTH FWDRESVHOTH Forward handover reserved ratio
TRMLOADTH BWDRESVHOTH Backward handover reserved ratio
TRMLOADTH FWDCONGTH Forward congestion remain ratio
TRMLOADTH BWDCONGTH Backward congestion remain ratio
Forward congestion clear remain

TRMLOADTH FWDCONGCLRTH ratio
Backward congestion clear remain

TRMLOADTH BWDCONGCLRTH ratio
Forward overload congestion

TRMLOADTH FWDOVLDTH remain ratio

TRMLOADTH BWDOVLDTH remain ratio
Forward overload congestion clear

TRMLOADTH FWDOVLDCLRTH remain ratio

TRMLOADTH BWDOVLDCLRTH clear remain ratio
TRMMAP TMI TRMMAP ID
TRMMAP REMARK Remark
TRMMAP ITFT Interface Type
TRMMAP TRANST Transport Type
TRMMAP CCHPRIPATH Common channel primary path
TRMMAP CCHSECPATH Common channel secondary path
TRMMAP SIPPRIPATH IMS SRB primary path

TRMMAP SIPSECPATH IMS SRB secondary path
TRMMAP SRBPRIPATH SRB primary path
TRMMAP SRBSECPATH SRB secondary path
TRMMAP VOICEPRIPATH AMR voice primary path
TRMMAP VOICESECPATH AMR voice secondary path

R99 CS conversational primary
TRMMAP CSCONVPRIPATH path
R99 CS conversational secondary

TRMMAP CSCONVSECPATH path
TRMMAP CSSTRMPRIPATH R99 CS streaming primary path
TRMMAP CSSTRMSECPATH R99 CS streaming secondary path
R99 PS conversational primary

TRMMAP PSCONVPRIPATH path
R99 PS conversational secondary
TRMMAP PSCONVSECPATH path
TRMMAP PSSTRMPRIPATH R99 PS streaming primary path
TRMMAP PSSTRMSECPATH R99 PS streaming secondary path
R99 PS high PRI interactive

TRMMAP PSINTHGHPRIPATH primary path
R99 PS high PRI interactive

TRMMAP PSINTHGHSECPATH secondary path
R99 PS middle PRI interactive
TRMMAP PSINTMIDPRIPATH primary path
R99 PS middle PRI interactive

TRMMAP PSINTMIDSECPATH secondary path
R99 PS low PRI interactive

TRMMAP PSINTLOWPRIPATH primary path
R99 PS low PRI interactive

TRMMAP PSINTLOWSECPATH secondary path
TRMMAP PSBKGPRIPATH R99 PS background primary path

R99 PS background secondary
TRMMAP PSBKGSECPATH path
TRMMAP HDSRBPRIPATH HSDPA Signal primary path
TRMMAP HDSRBSECPATH HSDPA Signal secondary path
TRMMAP HDSIPPRIPATH HSDPA IMS Signal primary path
HSDPA IMS Signal secondary

TRMMAP HDSIPSECPATH path
TRMMAP HDVOICEPRIPATH HSDPA Voice primary path
TRMMAP HDVOICESECPATH HSDPA Voice secondary path
HSDPA conversational primary

TRMMAP HDCONVPRIPATH path
HSDPA conversational secondary

TRMMAP HDCONVSECPATH path
TRMMAP HDSTRMPRIPATH HSDPA streaming primary path

TRMMAP HDSTRMSECPATH HSDPA streaming secondary path
HSDPA high PRI interactive

TRMMAP HDINTHGHPRIPATH primary path
HSDPA high PRI interactive

TRMMAP HDINTHGHSECPATH secondary path
HSDPA middle PRI interactive

TRMMAP HDINTMIDPRIPATH primary path
HSDPA middle PRI interactive

TRMMAP HDINTMIDSECPATH secondary path
HSDPA low PRI interactive
TRMMAP HDINTLOWPRIPATH primary path
HSDPA low PRI interactive

TRMMAP HDINTLOWSECPATH secondary path
TRMMAP HDBKGPRIPATH HSDPA background primary path
HSDPA background secondary

TRMMAP HDBKGSECPATH path
TRMMAP HUSRBPRIPATH HSUPA Signal primary path

TRMMAP HUSRBSECPATH HSUPA Signal secondary path
TRMMAP HUSIPPRIPATH HSUPA IMS Signal primary path
HSUPA IMS Signal secondary

TRMMAP HUSIPSECPATH path
TRMMAP HUVOICEPRIPATH HSUPA Voice primary path
TRMMAP HUVOICESECPATH HSUPA Voice secondary path

HSUPA conversational primary
TRMMAP HUCONVPRIPATH path
HSUPA conversational secondary

TRMMAP HUCONVSECPATH path
TRMMAP HUSTRMPRIPATH HSUPA streaming primary path
TRMMAP HUSTRMSECPATH HSUPA streaming secondary path
HSUPA high PRI interactive

TRMMAP HUINTHGHPRIPATH primary path
HSUPA high PRI interactive
TRMMAP HUINTHGHSECPATH secondary path
HSUPA middle PRI interactive

TRMMAP HUINTMIDPRIPATH primary path
HSUPA middle PRI interactive

TRMMAP HUINTMIDSECPATH secondary path
HSUPA low PRI interactive

TRMMAP HUINTLOWPRIPATH primary path
HSUPA low PRI interactive

TRMMAP HUINTLOWSECPATH secondary path
TRMMAP HUBKGPRIPATH HSUPA background primary path
HSUPA background secondary

TRMMAP HUBKGSECPATH path
TSCROSS SRN Subrack No.
TSCROSS SN Slot No.
TSCROSS SRCPORTNO Source port No.
TSCROSS SRCTSMASK Source timeslot mask
TSCROSS DSTPORTNO Destination port No.
TSCROSS DSTTSMASK Destination timeslot mask
TSCROSS TSCROSSX Time slot cross index

TZ ZONET TimeZone
TZ DST DaylightSave
TZ SM StartType
TZ SMONTH Start month

TZ SDAY Start date
TZ SWSEQ Start week sequence
TZ SWEEK Start week
TZ ST StartTime
TZ EM EndType
TZ EMONTH End month

TZ EDAY End date
TZ EWSEQ End week sequence
TZ EWEEK End week
TZ ET EndTime
TZ TO AdjustMethod
U2GNCELL RNCId RNC ID
U2GNCELL CellId Cell ID
U2GNCELL GSMCellIndex GSM Cell Index

U2GNCELL CIOOffset Neighboring Cell-Oriented CIO
U2GNCELL Qoffset1sn Qoffset1sn
U2GNCELL Qrxlevmin Min RX Level
U2GNCELL TpenaltyHcsReselect HCS Cell Reselect Penalty Timer
U2GNCELL TempOffset1 HCS Cell Reselect TempOffset1
U2GNCELL BlindHoFlag Blind Handover Flag
U2GNCELL BlindHOPrio Blind Handover Priority
U2GNCELL DRDEcN0Threshhold DRD Ec/No Threshold
U2GNCELL SIB11Ind SIB11 Indicator
U2GNCELL SIB12Ind SIB12 Indicator
U2GNCELL NPrioFlag Neighboring Cell Priority Flag
U2GNCELL NPrio Priority of Neighboring Cell
U2GNCELL MBDRFlag Flag of MBDR Cell

U2GNCELL MBDRPrio MBDR Cell Periority
U2GNCELL SRVCCSwitch Neighboring Cell Support Srvcc
UACALGO AcRstrctSwitch AC Restriction Switch
UACALGO AcRstrctPercent AC Restriction Percent
UACALGO AcIntervalOfCell AC Restriction Interval Of Cell
UACALGO AcRstrctIntervalLen AC Restriction Interval length

AC Restriction Interval of Cell By
UACALGO IuAcIntervalOfCell IU
UADMCTRL AFSetObj AFSetObj
UADMCTRL UlSrbActFactor UL AF of SRB
UADMCTRL DlSrbActFactor DL AF of SRB
UADMCTRL UlAmrConvAF UL AF of R99 AMR conv service
UADMCTRL DlAmrConvAF DL AF of R99 AMR conv service

UL AF of R99 non AMR conv
UADMCTRL UlNonAmrConvAF service
DL AF of R99 non AMR conv
UADMCTRL DlNonAmrConvAF service
UADMCTRL UlStreamAF UL AF of R99 Streaming service
UADMCTRL DlStreamAF DL AF of R99 Streaming service
UADMCTRL UlInteractAF UL AF of R99 interactive service
UADMCTRL DlInteractAF DL AF of R99 interactive service
UADMCTRL UlBackgroundAF UL AF of R99 background service
UADMCTRL DlBackgroundAF DL AF of R99 background service
UADMCTRL MbmsAF AF of MBMS service
UADMCTRL HsupaConvAF AF of hsupa conv service
UADMCTRL HsdpaConvAF AF of hsdpa conv service

UADMCTRL HsupaStreamAF AF of hsupa streaming service
UADMCTRL HsdpaStreamAF AF of hsdpa streaming service
UADMCTRL HsupaInteractAF AF of hsupa interactive service
UADMCTRL HsdpaInteractAF AF of hsdpa interactive service
UADMCTRL HsupaBackGroundAF AF of hsupa background service
UADMCTRL HsdpaBackGroundAF AF of hsdpa background service
UAICH CellId Cell ID
UAICH PRACHPhyChId PRACH ID
UAICH PhyChId AICH ID
UAICH AICHTxTiming AICH Transmission Timing
UAICH STTDInd STTD Indicator
UAICHPWROFFSET CellId Cell ID
UAICHPWROFFSET AICHPowerOffset AICH Power Offset

Average CPU usage threshold for
UALMTHD USRPLNCPUALMTHD generating an alarm
Average CPU usage threshold for
UALMTHD USRPLNCPUCLRTHD clearing an alarm
Average GBR usage threshold for
UALMTHD USRPLNGBRALMTHD generating an alarm
Average GBR usage threshold for
UALMTHD USRPLNGBRCLRTHD clearing an alarm
UAMRC DlThdE1 DL E1 Event Relative Threshold
UAMRC DlThdE2 DL E2 Event Relative Threshold
UAMRC DlThdF1 DL F1 Event Relative Threshold
UAMRC DlThdF2 DL F2 Event Relative Threshold
UAMRC UlModeChangeTimerLen UL Mode Change Timer Length

DL Mode Change Waiting Timer
UAMRC DlModeChangeTimerLen Length
Max Mode Of Narrowband AMRC

UAMRC GoldMaxMode for Golden Users
Max Mode of Narrowband AMRC

UAMRC SilverMaxMode for Silver Users

UAMRC CopperMaxMode for Copper Users
UAMRCWB DlThdE1 DL E1 Event Relative Threshold
UAMRCWB DlThdE2 DL E2 Event Relative Threshold
UAMRCWB DlThdF1 DL F1 Event Relative Threshold
UAMRCWB DlThdF2 DL F2 Event Relative Threshold
UAMRCWB UlModeChangeTimerLen UL Mode Change Timer Length

DL Mode Change Waiting Timer
UAMRCWB DlModeChangeTimerLen Length
Max Mode Of Wideband AMRC for

UAMRCWB GoldMaxMode Golden Users
Max Mode of Wideband AMRC for

UAMRCWB SilverMaxMode Silver Users

UAMRCWB CopperMaxMode Copper Users
UAUTONCELLDETECT SRN Subrack No.
UAUTONCELLDETECT SN Slot No.
Switch for Detecting Missing Intra-

UAUTONCELLDETECT AutoIntraNCellSwitch Freq Neighboring Cells
Switch for Detecting Missing Inter-
UAUTONCELLDETECT AutoInterNCellSwitch Freq Neighboring Cells
UAUTONCELLDETECT MeasObjNum Number of Measurement Object
UAUTONCELLDETECT BandInd1 Band Indicator 1
UAUTONCELLDETECT DLMeasFreq1 Downlink UARFCN 1
Start Scrambling Code of

UAUTONCELLDETECT StartSC1 UARFCN 1
End Scrambling Code of UARFCN

UAUTONCELLDETECT EndSC1 1






Switch for Detecting Missing Inter-

UAUTONCELLDETECT AutoIRATNCellSwitch RAT Neighboring Cells
UAUTONCELLDETECT StartNCC Inter-RAT Start NCC
UAUTONCELLDETECT ENDNCC Inter-RAT End NCC
UAUTONCELLDETECT StartBCC Inter-RAT Start BCC
UAUTONCELLDETECT EndBCC Inter-RAT End BCC
UAUTONCELLDETECT InterRatBandInd Inter-RAT Band Indicator
UAUTONCELLDETECT StartFreq Inter-RAT Start ARFCN
UAUTONCELLDETECT EndFreq Inter-RAT End ARFCN
UBCH CellId Cell ID
UBCH TrChId BCH ID
UBCH BCHPower BCH Transmit Power
UCACALGOSWITCH CacSwitch CAC algorithm switch

UCACALGOSWITCH RsvdPara1 Reserved parameter 1
UCALLSHOCKCTRL CallShockCtrlSwitch Call Shock Control Switch
UCALLSHOCKCTRL RegByFachSwitch Register Bear by Fach Switch

Call Shock Judge Period time
UCALLSHOCKCTRL CallShockJudgePeriod length
System Call Shock Trigger

UCALLSHOCKCTRL SysTotalRrcNumThd Threshold
AMR_RRC Number per Second
UCALLSHOCKCTRL SysAmrRrcNum for System
HiPri_RRC Number per Second
UCALLSHOCKCTRL SysHighPriRrcNum for System
Max RRC_REJ Number per
UCALLSHOCKCTRL SysRrcRejNum Second for System
NodeB Call Shock Trigger

UCALLSHOCKCTRL NBTotalRrcNumThd Threshold
UCALLSHOCKCTRL NBAmrRrcNum for NodeB
UCALLSHOCKCTRL NBHighPriRrcNum for NodeB
UCALLSHOCKCTRL CellTotalRrcNumThd Cell Call Shock Trigger Threshold
UCALLSHOCKCTRL CellAmrRrcNum for Cell
UCALLSHOCKCTRL CellHighPriRrcNum for Cell
UCAPARATERANGE DlCapacitySelect Downlink Rate Selection
UCAPARATERANGE DlRateThreshold1 Downlink Rate Threshold 1
UCAPARATERANGE UlCapacitySelect Uplink Rate Selection
UCAPARATERANGE UlRateThreshold1 Uplink Rate Threshold 1

UCBSADDR SRN Subrack No.
UCBSADDR SN Slot No.
UCBSADDR CnOpIndex Cn Operator Index
UCBSADDR RNCIPADDR CBS RNC IP Address
UCBSADDR CBCIPADDR CBS CBC IP Address
UCBSADDR CBCMASK Subnet Mask

UCBSAREA AreaId CBS Area ID
UCBSAREA CnOpIndex CN Operator Index
UCBSAREA AreaType CBS Area NameCBS Area Type
UCBSAREA LAC Location Area Code
UCBSAREA CellId Cell ID

UCBSAREA AreaId cell broadcast area identifier
UCBSMSG MsgIndex CBS Message Index

UCBSMSG MsgTypeId CBS Message ID
UCBSMSG GeographicalScope Geography Scope
UCBSMSG Priority CBS Message Priority
UCBSMSG RepetPeriod CBS Message Repeat Period

Number of Emergency
UCBSMSG NumOfBrdcstReq Broadcasting Messages
UCBSMSG CodeType Coding Scheme
UCBSMSG AreaID CBS Area ID
UCBSMSG EmergencyType Emergency Broadcasting Type

UCBSMSG CBSMsg Message Content
UCBSMSG CBSMsg CBS Message Content
UCCP NodeBName NodeB Name
UCCP PN Port No.
UCCP CARRYLNKT Bearing Link Type
UCCP SAALLNKN SAAL link No.
UCCP SCTPLNKN SCTP link No.
UCCP MAINLINK Main Link Type
UCCP STACKMODTYPE Link modify type
UCCP MAINLINK Main Link Type
UCDRFILE MODE File Output

Period Mode
of New File
UCDRFILE CYCLE Generation[min]
UCELL CellId Cell ID
UCELL CellName Cell Name

UCELL MaxTxPower Max Transmit Power of Cell
UCELL BandInd Band Indicator
UCELL PeerIsValid Peer Cell Is Valid Or Not
UCELL PeerCellId Peer Cell ID
UCELL CnOpGrpIndex Cn Operator Group Index
UCELL UARFCNUplinkInd UL Frequency Ind

UCELL UARFCNUplink Uplink UARFCN
UCELL UARFCNDownlink Downlink UARFCN
UCELL TCell Time Offset
UCELL NInsyncInd Num of Continuous in Sync Ind
Num of Continuous Out of Sync

UCELL NOutsyncInd Ind
UCELL TRlFailure Radio Link Failure Timer Length
UCELL PScrambCode DL Primary Scrambling Code
UCELL TxDiversityInd TX Diversity Indication

UCELL SpgId Service Priority Group Identity
UCELL NodeBName NodeB Name
UCELL LoCell Local Cell ID
UCELL LAC Location Area Code
UCELL SAC Service Area Code
UCELL CfgRacInd RAC Configuration Indication
UCELL RAC Routing Area Code
UCELL STTDSupInd STTD Support Indicator
UCELL CP1SupInd CP1 Support Indicator
UCELL ClosedLoopTimeAdjustMode Closed Loop Time Adjust Mode
DPCH Tx Diversity Mode for Other

UCELL DpchDivModforOther User
FDPCH Tx Diversity Mode for
UCELL FdpchDivModforOther Other User
DPCH Tx Diversity Mode for

UCELL DpchDivModforMIMO MIMO User
UCELL FdpchDivModforMIMO MIMO User
Tx Diversity Mode for DC-HSDPA
UCELL DivModforDCHSDPA User
UCELL CIO Cell Oriented Cell Individual Offset
UCELL VPLimitInd Cell VP Limit Indicator
UCELL DSSFlag DSS Cell Flag
Maximum TX Power in Small DSS

UCELL DSSSmallCovMaxTxPower Coverage
UCELL DPGId Hierarchy ID of Terminal Type
UCELL URANUM URA number
UCELL URA1 URA ID 1
UCELL URA2 URA ID 2
UCELL URA3 URA ID 3
UCELL URA4 URA ID 4
UCELL URA5 URA ID 5
UCELL URA6 URA ID 6
UCELL URA7 URA ID 7
UCELL URA8 URA ID 8
UCELL SupBmc CBS support

UCELL CBSOpIndex CBS Operator Index
UCELL CBSSAC CBS SAC
UCELL PCPICHPower PCPICH Transmit Power
PCPICH TX Power in Small DSS

UCELL DSSSmallCovPCPICHPower Coverage
UCELL PSCHPower PSCH Transmit Power
UCELL SSCHPower SSCH Transmit Power
UCELL ScpichPower SCPICH transmit power[0.1dB]
UCELL BCHPower BCH Transmit Power
UCELL CellId Cell ID
UCELL CellName Cell Name
UCELL ClusterName Cluster Name

UCELL NodeBName NodeB Name
UCELL LoCell Local Cell ID
UCELL FpSynInd FP Synchronization Indicator
UCELL PCPICHPower PCPICH Transmit Power
UCELL MaxPCPICHPower Max Transmit Power of PCPICH
UCELL MinPCPICHPower Min Transmit Power of PCPICH
UCELL PSCHPower PSCH Transmit Power
UCELL SSCHPower SSCH Transmit Power
UCELL BCHPower BCH Transmit Power
UCELL McchFachMaxPower Max FACH Power of MCCH
UCELL MichPower MICH Power

UCELLACCESSSTRICT CellId Cell ID
UCELLACCESSSTRICT CellReservedForOperatorUse Cell reserved for operator use
UCELLACCESSSTRICT CellReservationExtension Cell reservation extension
UCELLACCESSSTRICT IsAccessClass0Barred Access class 0 barred indicator

UCELLACCESSSTRICT IdleCellBarred Cell barred indicator for SIB3
Intra-freq cell reselection ind for

UCELLACCESSSTRICT IdleIntraFreqReselection SIB3
UCELLACCESSSTRICT IdleTbarred Time barred for SIB3

UCELLACCESSSTRICT ConnCellBarred Cell barred indicator for SIB4
Intra-freq cell reselection ind for

UCELLACCESSSTRICT ConnIntraFreqReselection SIB4
UCELLACCESSSTRICT ConnTbarred Time barred for SIB4
UCELLACINFO CellId Cell ID
UCELLACINFO LAC Location Area Code
UCELLACINFO SAC Service Area Code
UCELLACINFO CfgRacInd RAC Configuration Indication
UCELLACINFO RAC Routing Area Code
UCELLALGOSWITCH CellId Cell ID

UCELLALGOSWITCH NBMCacAlgoSwitch Cell CAC algorithm switch
UCELLALGOSWITCH NBMUlCacAlgoSelSwitch Uplink CAC algorithm switch
UCELLALGOSWITCH NBMDlCacAlgoSelSwitch Downlink CAC algorithm switch
UCELLALGOSWITCH NBMLdcAlgoSwitch Cell LDC algorithm switch
UCELLALGOSWITCH NBMMachsResetAlgoSelSwitch Mac-hs Reset algorithm switch

UCELLALGOSWITCH HspaPlusSwitch Cell Hspa Plus function switch
Cell Hspa Enhanced function

UCELLALGOSWITCH HspaEnhSwitch switch
UCELLALGOSWITCH CellCapacityAutoHandleSwitch Cell Capability Auto Handle Switch
Inter-freq Handover Select User

UCELLALGOSWITCH NbmLdcUeSelSwitch algorithm switch
UCELLALGOSWITCH RsvdPara1 Reserved parameter 1
UCELLALGOSWITCH OffloadSwitch Offload Switch
BE rate reduction switch based on

UCELLALGOSWITCH BERateReduceOnFairnessSwitch fairness
UCELLAMRC CellId Cell ID
Max Mode Of Narrowband AMRC

UCELLAMRC GoldMaxMode for Golden Users

UCELLAMRC SilverMaxMode for Silver Users

UCELLAMRC CopperMaxMode for Copper Users
UCELLAMRCWB CellId Cell ID
Max Mode Of Wideband AMRC for

UCELLAMRCWB GoldMaxMode Golden Users

UCELLAMRCWB SilverMaxMode Silver Users
UCELLAMRCWB CopperMaxMode Copper Users
UCELLCAC CellId Cell ID
UCELLCAC CellEnvType Cell environment type
UCELLCAC UlNonCtrlThdForAMR UL threshold of Conv AMR service
UL threshold of Conv non_AMR

UCELLCAC UlNonCtrlThdForNonAMR service
UCELLCAC UlNonCtrlThdForOther UL threshold of other services
UCELLCAC DlConvAMRThd DL threshold of Conv AMR service
DL threshold of Conv non_AMR

UCELLCAC DlConvNonAMRThd service
UCELLCAC DlOtherThd DL threshold of other services
UCELLCAC UlNonCtrlThdForHo UL handover access threshold
UCELLCAC DlHOThd DL handover access threshold

UCELLCAC UlCellTotalThd UL total power threshold
UCELLCAC DlCellTotalThd DL total power threshold
UL common channel load reserved

UCELLCAC UlCCHLoadFactor coefficient
DL common channel load reserved
UCELLCAC DlCCHLoadRsrvCoeff coefficient
UCELLCAC UlTotalEqUserNum UL total equivalent user number
UCELLCAC DlTotalEqUserNum DL total equivalent user number
Low priority HSUPA user PBR

UCELLCAC HsupaLowPriorityUserPBRThd threshold
Equal priority HSUPA user PBR

UCELLCAC HsupaEqualPriorityUserPBRThd threshold
High priority HSUPA user PBR

UCELLCAC HsupaHighPriorityUserPBRThd threshold
UCELLCAC UlHsDpcchRsvdFactor UL HS-DPCCH reserve factor
UCELLCAC HsdpaStrmPBRThd Hsdpa streaming PBR threshold
UCELLCAC HsdpaBePBRThd HSDPA best effort PBR threshold
UCELLCAC MaxHsdpaUserNum Maximum HSDPA user number

Max UL TX power of
UCELLCAC MaxUlTxPowerforConv conversational service
Max UL TX power of streaming

UCELLCAC MaxUlTxPowerforStr service
Max UL TX power of interactive

UCELLCAC MaxUlTxPowerforInt service
Max UL TX power of background

UCELLCAC MaxUlTxPowerforBac service
UCELLCAC BackgroundNoise Background noise
UCELLCAC DefPcpichEcNo Default PCPICH Ec/No

Auto-adaptive background noise
UCELLCAC BGNSwitch update switch
Background noise update
UCELLCAC BGNAdjustTimeLen continuance Time
Equivalent user number threshold
UCELLCAC BGNEqUserNumThd for background noise
UCELLCAC MaxHsupaUserNum Maximum HSUPA user number
UCELLCAC DlHSUPARsvdFactor Dl HSUPA reserved factor
UCELLCAC DlMBMSRsvdFactor DL MBMS reserved factor
UCELLCAC MtchRsvPwr MTCH reserve power
UCELLCAC MtchRsvSf MTCH reserve SF
UCELLCAC MtchMaxPwr MTCH maximal power
UCELLCAC MtchMaxSf MTCH maximal SF
UCELLCAC UlHoCeResvSf UL handover credit reserved SF
DL handover credit and code

UCELLCAC DlHoCeCodeResvSf reserved SF
Background noise update start
UCELLCAC BgnStartTime time
UCELLCAC BgnEndTime Background noise update end time

Background noise update trigger
UCELLCAC BgnUpdateThd threshold
Background noise abnormal
UCELLCAC BgnAbnormalThd threshold
UCELLCAC MAXEFACHUserNum Maximum EFACH user number
Cell Uplink Capacity of Equal User

UCELLCAC CellUlEquNumCapacity Number
UCELLCAC MaxERACHUserNum Maximum ERACH user number

Power Resource Reserved for
UCELLCAC FreeuserGbpRsvd Free Users
Threshold of Maximum
UCELLCAC HsdpaMaxGBPThd Guaranteed Bit Rates for HSDPA
Threshold of Maximum
UCELLCAC HsupaMaxGBPThd Guaranteed Bit Rates for HSUPA
UCELLCBSDRX CellId Cell ID
UCELLCBSSAC CellId Cell ID
UCELLCBSSAC CnOpIndex Cn Operator Index

UCELLCBSSAC CBSSAC CBS SAC
UCELLCBSSAC MsgInd Message Indicator
UCELLCBSSAC MsgContent Msg Content
UCELLCMCF CellId Cell ID
UCELLCMCF CmcfCellType CM Cell Type

UCELLCMCF DlSFTurnPoint DL SF Threshold
UCELLCMCF UlSFTurnPoint UL SF threshold
UCELLDCCC CellId Cell ID

BE Event F Reporting Power
UCELLDCCC BePwrMargin Margin
Comb Event F Reporting Power
UCELLDCCC CombPwrMargin Margin
UCELLDCCC UlFullCvrRate Uplink Full Coverage Bit Rate
UCELLDCCC DlFullCvrRate Downlink Full Coverage Bit Rate
UCELLDISTANCEREDIRECTIO
N CellId Cell ID
N RedirSwitch Redirection Switch
N DelayThs Propagation delay threshold
N RedirFactorOfLDR Redirection Factor Of LDR
N RedirFactorOfNorm Redirection Factor Of Normal
UCELLDRD CellId Cell ID

Maximum Times of Inter-RAT
UCELLDRD DRMaxGSMNum Direct Retry
UCELLDRD ServiceDiffDrdSwitch Service Steering DRD Switch
UCELLDRD LdbDRDSwitchDCH Load balance DRD switch for DCH
Load balance DRD switch for

UCELLDRD LdbDRDSwitchHSDPA HSDPA
UCELLDRD LdbDRDchoice Load Balancing DRD Choice

Dl load balance DRD power
UCELLDRD LdbDRDLoadRemainThdDCH remain threshold for DCH
UCELLDRD LdbDRDLoadRemainThdHSDPA remain threshold for HSDPA
UCELLDRD CodeBalancingDrdSwitch Code Balancing DRD Switch

Minimum SF Threshold for Code
UCELLDRD CodeBalancingDrdMinSFThd Balancing DRD
Code Occupancy Thres for Code
UCELLDRD CodeBalancingDrdCodeRateThd Balancing DRD
UCELLDRD ReDirBandInd ReDirection target band indicator

Redirection Target UL Frequency
UCELLDRD ReDirUARFCNUplinkInd Index
UCELLDRD ReDirUARFCNUplink Redirection target uplink UARFCN
Redirection target downlink
UCELLDRD ReDirUARFCNDownlink UARFCN
Uplink load balance DRD Switch
UCELLDRD ULLdbDRDSwitchDcHSDPA for DC-HSDPA
ULLdbDRDLoadRemainThdDcHS Uplink load balance DRD remain
UCELLDRD DPA threshold for DC-HSDPA
UCELLDRD DPGDRDSwitch Terminal Type Hierarchy Switch
UCELLDRDMIMO CellId Cell ID

DRD Switch for LegacyH under
UCELLDRDMIMO LegacyHDrdSwitchOfSTTD STTD
DRD Switch for LegacyH under P
UCELLDRDMIMO LegacyHDrdSwitchOfSCPICH and S CPICH
UCELLDRDMIMO CQIRefValueOfSTTD CQI reference value for STTD

CQI reference value for P and S
UCELLDRDMIMO CQIRefValueOfSCPICH CPICH
UCELLDRDMIMO ExcellentCQIThdOfSTTD Excellent CQI Threshold for STTD
UCELLDRDMIMO GoodCQIThdOfSTTD Good CQI Threshold for STTD
UCELLDRDMIMO BadCQIThdOfSTTD Bad CQI Threshold for STTD

Excellent CQI Threshold for P and
UCELLDRDMIMO ExcellentCQIThdOfSCPICH S CPICH
Good CQI Threshold for P and S
UCELLDRDMIMO GoodCQIThdOfSCPICH CPICH
Bad CQI Threshold for P and S
UCELLDRDMIMO BadCQIThdOfSCPICH CPICH
UCELLDSACMANUALPARA CellId Cell ID
UCELLDSACMANUALPARA CnOpIndex CN Operator index
UCELLDSACMANUALPARA CsRestriction Restriction for CS
UCELLDSACMANUALPARA PsRestriction Restriction for PS
UCELLDSACMANUALPARA RestrictionType Restriction Type

UCELLDSACMANUALPARA AcRestriction AC Restriction Indicator
Number of restrained AC every

UCELLDSACMANUALPARA NumberOfACs time
UCELLDSACMANUALPARA AcRange Range of restrained AC
UCELLDSACMANUALPARA AcRstrctIntervalLen Interval of DSAC Restriction
UCELLDYNSHUTDOWN CellId Cell ID
UCELLDYNSHUTDOWN DynShutdownSwitch Cell Dynamic ShutDown Switch

First Cell Dynamic ShutDown
UCELLDYNSHUTDOWN StartTime1 Interval Start Time
First Cell Dynamic ShutDown

UCELLDYNSHUTDOWN EndTime1 Interval End Time
Second Cell Dynamic ShutDown

Second Cell Dynamic ShutDown

Third Cell Dynamic ShutDown

Third Cell Dynamic ShutDown

UCELLDYNSHUTDOWN DynShutDownType Cell Dynamic ShutDown Type
Cell Dynamic ShutDown Total

UCELLDYNSHUTDOWN TotalUserNumThd User Number Threshold
Cell Dynamic ShutDown Hsdpa

UCELLDYNSHUTDOWN HsdpaUserNumThd User Number Threshold
Cell Dynamic ShutDown Hsupa

UCELLDYNSHUTDOWN HsupaUserNumThd User Number Threshold
Cell Dynamic ShutDown

Neighbour Cell Load Remain
UCELLDYNSHUTDOWN NCellLdrRemainThd Threshold
UCELLDYNSHUTDOWN HighPriSPI High-Priority Scheduling Indicator
UCELLEDRX CellId Cell ID
T321 in CELL_FACH State and

UCELLEDRX EDRXT321 DRX Mode
UCELLEDRX EDRXCycle DRX Cycle in CELL_FACH State
Rx Burst in CELL_FACH State and

UCELLEDRX EDRXBurst DRX Mode
DRX Interruption by HS-DSCH
UCELLEDRX EDRXInterruptbyHSDSCHData Data
UCELLEFACH CellId Cell ID
UCELLEFACH EFACHDTCHGBP EFACH DTCH GBP
UCELLEFACH BcchHsscchPower BCCH HS-SCCH Power
UCELLEFACH BcchHspdschPower BCCH HS-PDSCH Power
UCELLEFACH CCCHGBR CCCH MAC-c Flow GBR
UCELLEFACH CCCHMBR CCCH MAC-c Flow MBR
UCELLEFACH SRBGBR SRB MAC-c Flow GBR
UCELLEFACH SRBMBR SRB MAC-c Flow MBR
UCELLEFACH CONVGBR Conversational MAC-c Flow GBR
UCELLEFACH CONVMBR Conversational MAC-c Flow MBR
UCELLEFACH STREAMGBR Streaming MAC-c Flow GBR
UCELLEFACH STREAMMBR Streaming MAC-c Flow MBR
UCELLEFACH INTERACTGBR Interactive MAC-c Flow GBR
UCELLEFACH INTERACTMBR Interactive MAC-c Flow MBR

UCELLEFACH BGGBR Background MAC-c Flow GBR
UCELLEFACH BGMBR Background MAC-c Flow MBR
UCELLEFACH IMSGBR IMS MAC-c Flow GBR
UCELLEFACH IMSMBR IMS MAC-c Flow MBR
UCELLEPCH CellId Cell ID
EPCH Transmission Block Size

UCELLEPCH EPCHTbSizeInd1 Index 1
EPCH Transmission Block Size

UCELLEPCH EPCHTbSizeInd2 Index 2
UCELLEPCH EPCHHSSCCHPower HS-SCCH Power for EPCH UEs
UCELLEPCH EPCHHSPDSCHPower HS-PDSCH Power Under EPCH
Number of EPCHPCCH
UCELLEPCH EPCHPCCHTxNum Transmissions
UCELLEPCH EPCHTOAWS TOAWS Under EPCH
UCELLEPCH EPCHTOAWE TOAWE Under EPCH
UCELLEPCH EPCHMaxRate Maximum EPCH Access Rate
UCELLFRC CellId Cell ID
UL BE traffic DCH decision

UCELLFRC UlBeTraffDecThs threshold
DL BE traffic DCH decision

UCELLFRC DlBeTraffDecThs threshold
Allowing Code Resource Saving
UCELLFRC AllowedSaveCodeResource Mode indication
UCELLFRC EcN0Ths Ec/N0 threshold

UCELLFRC EcN0EffectTime Ec/N0 effective time
Configure Channel Type for RRC
UCELLFRC RrcCauseSigChTypeInd Connection Establishment
Index of Channel Type for RRC
UCELLFRC RrcCauseSigChTypeId Connection Establishment
UCELLFREQUENCY RNCId RNC ID
UCELLFREQUENCY CellId Cell ID
UCELLFREQUENCY BandInd Band Indicator
UCELLFREQUENCY UARFCNUplinkInd UL Frequency Ind
UCELLFREQUENCY UARFCNUplink Uplink UARFCN

UCELLFREQUENCY UARFCNDownlink Downlink UARFCN
UCELLGPSFRMTIMING CellId Cell ID
UCELLGPSFRMTIMING StartFlag GPS Frame Timing Active Flag
UCELLHCS CellId Cell ID
UCELLHCS UseOfHcs Use of HCS

UCELLHCS HCSPrio HCS priority level
UCELLHCS SsearchHCS HCS cell reselection threshold
UCELLHCS SHCSRat HCS inter-rat reselection threshold

Quality threshold for HCS
UCELLHCS Qhcs reselection
Time for evaluating max cell
UCELLHCS TCRmax reselection
UCELLHCS CRMaxNum Max number of cell reselection
Time before revert to low-mobility

UCELLHCS TCrmaxHyst meas
HCS search inter-rat limit
UCELLHCS SlimitSearchRat threshold
UCELLHCSHO CellId Cell ID
Algorithm Switch for UE Speed

UCELLHCSHO SpdEstSwitch Estimation
Time Window for UE Fast Speed

UCELLHCSHO TFastSpdEst Decision
Threshold for UE Fast Speed

UCELLHCSHO NFastSpdEst Decision
Period for UE Slow Speed
UCELLHCSHO TCycleSlow Decision
Time Window for UE Slow Speed

UCELLHCSHO TSlowSpdEst Decision
Threshold for UE Slow Speed

UCELLHCSHO NSlowSpdEst Decision
Time Window For Ping-Pong

UCELLHCSHO TRelateLength Handover Decision in Best Cell
UCELLHOCOMM CellId Cell ID
Inter-Frequency and Inter-RAT

UCELLHOCOMM InterFreqRATSwitch Coexist Switch
Inter-Freq and Inter-RAT Coexist

UCELLHOCOMM CoexistMeasThdChoice Measure Threshold Choice
UCELLHOCOMM CSServiceHOSwitch Inter-RAT CS Handover Switch
UCELLHOCOMM PSServiceHOSwitch Inter-RAT PS Handover Switch
UCELLHSDPA CellId Cell ID
UCELLHSDPA AllocCodeMode Allocate Code Mode
UCELLHSDPA HsPdschCodeNum Code Number for HS-PDSCH
UCELLHSDPA HsPdschMaxCodeNum Code Max Number for HS-PDSCH
UCELLHSDPA HsPdschMinCodeNum Code Min Number for HS-PDSCH
UCELLHSDPA HsScchCodeNum Code Number for HS-SCCH
UCELLHSDPA HspaPower The Offset of HSPA Total Power

UCELLHSDPA HsPdschMPOConstEnum HS-PDSCH MPO Constant
HARQ Preamble Capability
UCELLHSDPA HsdpcchPreambleSwitch Indication
UCELLHSDPA CodeAdjForHsdpaSwitch Code Adjust Switch for HSDPA
User Number for Code Adjust for

UCELLHSDPA CodeAdjForHsdpaUserNumThd HSDPA
Punish Timer Length for Code
UCELLHSDPA HCodeAdjPunshTimerLength Adjust for HSDPA
UCELLHSDPA MIMOMPOConstant MIMO MPO Constant[dB]
UCELLHSDPA CellId Cell ID
UCELLHSDPCCH CellId Cell ID
UCELLHSDPCCH CQIPO CQI Power Offset

UCELLHSDPCCH CQIPOforSHO CQI Power Offset Multi-RLS
UCELLHSDPCCH CQIReF CQI Repetition Factor
UCELLHSDPCCH CQIReFforSHO CQI Repetition Factor Multi-RLS
UCELLHSDPCCH CQIFbCk CQI Feedback Cycle k
UCELLHSDPCCH CQIFbCkforSHO CQI Feedback Cycle k Multi-RLS

CS Services CQI Feedback Cycle
UCELLHSDPCCH CQIFBckforConver k
MIMO Services CQI Feedback
UCELLHSDPCCH CQIFBckforMimo Cycle k
DC MIMO Services CQI Feedback
UCELLHSDPCCH CQIFBckforDcMimo Cycle k
UCELLHSUPA CellId Cell ID
UCELLHSUPA EagchCodeNum Code Number for E-AGCH
Code Number for E-RGCH/E-

UCELLHSUPA ErgchEhichCodeNum HICH
Maximum Target Uplink Load
UCELLHSUPA MaxTargetUlLoadFactor Factor
Target Non-serving E-DCH to

UCELLHSUPA NonServToTotalEdchPwrRatio Total E-DCH Power Ratio
UCELLID RNCId RNC ID
UCELLID SrcCellID Source Cell ID
UCELLID DesCellID Destination Cell ID
UCELLINTERFREQHOCOV CellId Cell ID

Inter-frequency Measure Report
UCELLINTERFREQHOCOV InterFreqReportMode Mode
Inter-frequency Measure Filter

UCELLINTERFREQHOCOV InterFreqFilterCoef Coeff
Inter-frequency Measure
Periodical Measurement Report
UCELLINTERFREQHOCOV PrdReportInterval Period
UCELLINTERFREQHOCOV HystFor2B 2B Hysteresis
UCELLINTERFREQHOCOV HystFor2D 2D Hysteresis
UCELLINTERFREQHOCOV HystFor2F 2F Hysteresis

UCELLINTERFREQHOCOV HystForPrdInterFreq HHO Hysteresis
UCELLINTERFREQHOCOV WeightForUsedFreq Weight for Used frequency
UCELLINTERFREQHOCOV TimeToTrig2B Event 2B Trigger Delay
UCELLINTERFREQHOCOV TimeToTrig2D Event 2D Trigger Delay
UCELLINTERFREQHOCOV TimeToTrig2F Event 2F Trigger Delay
UCELLINTERFREQHOCOV TimeToTrigForPrdInterFreq HHO Period Trigger Delay
Inter-freq CS Measure Start Ec/No

UCELLINTERFREQHOCOV InterFreqCSThd2DEcN0 THD
Inter-freq CS Measure Stop Ec/No

UCELLINTERFREQHOCOV InterFreqCSThd2FEcN0 THD
Inter-freq R99 PS Measure Start
UCELLINTERFREQHOCOV InterFreqR99PsThd2DEcN0 Ec/No THD
Inter-freq H Measure Start Ec/No

UCELLINTERFREQHOCOV InterFreqHThd2DEcN0 THD
Inter-freq R99 PS Measure Stop

UCELLINTERFREQHOCOV InterFreqR99PsThd2FEcN0 Ec/No THD
Inter-freq H Measure Stop Ec/No

UCELLINTERFREQHOCOV InterFreqHThd2FEcN0 THD
Inter-freq CS Measure Start RSCP

UCELLINTERFREQHOCOV InterFreqCSThd2DRSCP THD
Inter-freq CS Measure Stop RSCP

UCELLINTERFREQHOCOV InterFreqCSThd2FRSCP THD
UCELLINTERFREQHOCOV InterFreqR99PsThd2DRSCP RSCP THD
Inter-freq H Measure Start RSCP

UCELLINTERFREQHOCOV InterFreqHThd2DRSCP THD

UCELLINTERFREQHOCOV InterFreqR99PsThd2FRSCP RSCP THD
Inter-freq H Measure Stop RSCP

UCELLINTERFREQHOCOV InterFreqHThd2FRSCP THD
Inter-freq CS Target Frequency

UCELLINTERFREQHOCOV TargetFreqCsThdEcN0 Trigger Ec/No THD
Inter-freq HSPA Target Frequency

UCELLINTERFREQHOCOV TargetFreqHThdEcN0 Trigger Ec/No THD
Inter-freq R99 PS Target

UCELLINTERFREQHOCOV TargetFreqR99PsThdEcN0 Frequency Trigger Ec/No THD
Inter-freq CS Target Freqency
UCELLINTERFREQHOCOV TargetFreqCsThdRscp Trigger RSCP THD
Inter-freq HSPA Target Freqency

UCELLINTERFREQHOCOV TargetFreqHThdRscp Trigger RSCP THD

UCELLINTERFREQHOCOV TargetFreqR99PsThdRscp Frequency Trigger RSCP THD
Inter-freq CS Used frequency

UCELLINTERFREQHOCOV UsedFreqCSThdEcN0 trigger Ec/No THD
Inter-freq R99 PS Used frequency

UCELLINTERFREQHOCOV UsedFreqR99PsThdEcN0 trigger Ec/No THD
Inter-freq H Used frequency trigger

UCELLINTERFREQHOCOV UsedFreqHThdEcN0 Ec/No THD

UCELLINTERFREQHOCOV UsedFreqCSThdRSCP trigger RSCP THD

UCELLINTERFREQHOCOV UsedFreqR99PsThdRSCP trigger RSCP THD
UCELLINTERFREQHOCOV UsedFreqHThdRSCP RSCP THD
UCELLINTERFREQHOCOV InterFreqMeasTime Inter-freq Measure Timer Length
UCELLINTERFREQHOCOV PeriodFor2B 2B Event Retry Period
UCELLINTERFREQHOCOV AmntOfRpt2B 2B Event Retry Max Times
Inter-freq Coverage Handover

UCELLINTERFREQHOCOV TimeToInterfreqHO Trigger Delay
UCELLINTERFREQHONCOV CellId Cell ID

UCELLINTERFREQHONCOV InterFreqFilterCoef Coeff
UCELLINTERFREQHONCOV Hystfor2C 2C Hysteresis
UCELLINTERFREQHONCOV TrigTime2C Event 2C Trigger Delay
Inter-Freq Measure Target

UCELLINTERFREQHONCOV InterFreqCovHOThdEcN0 Frequency Trigger Ec/No THD
UCELLINTERFREQHONCOV InterFreqMeasTime Inter-freq Measure Timer Length
UCELLINTERFREQHONCOV PeriodFor2C 2C Event Retry Period
UCELLINTERFREQHONCOV AmntOfRpt2C Event 2C Retry Max Times
UCELLINTERRATHOCOV CellId Cell ID

UCELLINTERRATHOCOV InterRatReportMode Inter-RAT Report Mode
UCELLINTERRATHOCOV FilterCoefOf2D2F 2D/2F Filter Coefficient
UCELLINTERRATHOCOV MeasQuantityOf3A 3A Measure Quantity
UCELLINTERRATHOCOV InterRATFilterCoef Inter-RAT Filter Coefficient
UCELLINTERRATHOCOV WeightForUsedFreq Weight for Used Frequency
Inter-RAT Period Reporting

UCELLINTERRATHOCOV InterRATPeriodReportInterval Interval
UCELLINTERRATHOCOV Hystfor2D 2D Hysteresis
UCELLINTERRATHOCOV Hystfor2F 2F Hysteresis
UCELLINTERRATHOCOV Hystfor3A 3A Hysteresis
UCELLINTERRATHOCOV HystforInterRAT Inter-RAT Hysteresis
UCELLINTERRATHOCOV TrigTime2D 2D Event Trigger Delay Time
UCELLINTERRATHOCOV TrigTime2F 2F Event Trigger Delay Time
UCELLINTERRATHOCOV TrigTime3A 3A Event Trigger Delay Time
Time to Trigger Handover to Non-

UCELLINTERRATHOCOV TimeToTrigForNonVerify Verified GSM Cell
Time to Trigger Handover to
UCELLINTERRATHOCOV TimeToTrigForVerify Verified GSM Cell
UCELLINTERRATHOCOV BSICVerify BSIC Verify Switch
Inter-RAT CS Measure Start

UCELLINTERRATHOCOV InterRATCSThd2DEcN0 Ec/No THD
Inter-RAT CS Measure Stop Ec/No

UCELLINTERRATHOCOV InterRATCSThd2FEcN0 THD
Inter-RAT R99 PS Measure Start

UCELLINTERRATHOCOV InterRATR99PsThd2DEcN0 Ec/No THD
Inter-RAT HSPA Measure Start
UCELLINTERRATHOCOV InterRATHThd2DEcN0 Ec/No THD
Inter-RAT R99 PS Measure Stop

UCELLINTERRATHOCOV InterRATR99PsThd2FEcN0 Ec/No THD
Inter-RAT HSPA Measure Stop

UCELLINTERRATHOCOV InterRATHThd2FEcN0 Ec/No THD

UCELLINTERRATHOCOV InterRATCSThd2DRSCP RSCP THD
Inter-RAT CS Measure Stop

UCELLINTERRATHOCOV InterRATCSThd2FRSCP RSCP THD

UCELLINTERRATHOCOV InterRATR99PsThd2DRSCP RSCP THD
UCELLINTERRATHOCOV InterRATHThd2DRSCP RSCP THD

UCELLINTERRATHOCOV InterRATR99PsThd2FRSCP RSCP THD

UCELLINTERRATHOCOV InterRATHThd2FRSCP RSCP THD
Inter-RAT CS Handover Decision

UCELLINTERRATHOCOV TargetRatCsThd THD
Inter-RAT R99 PS Handover
UCELLINTERRATHOCOV TargetRatR99PsThd Decision THD
Inter-RAT HSPA Handover

UCELLINTERRATHOCOV TargetRatHThd Decision THD
Inter-RAT CS Used Frequency
UCELLINTERRATHOCOV UsedFreqCsThdEcN0 Trigger Ec/No THD
Inter-RAT R99 PS Used

UCELLINTERRATHOCOV UsedFreqR99PsThdEcN0 Frequency Trigger Ec/No THD
Inter-RAT HSPA Used Frequency
UCELLINTERRATHOCOV UsedFreqHThdEcN0 Trigger Ec/No THD

UCELLINTERRATHOCOV UsedFreqCsThdRscp Trigger RSCP THD
UCELLINTERRATHOCOV UsedFreqR99PsThdRscp Frequency Trigger RSCP THD

UCELLINTERRATHOCOV UsedFreqHThdRscp Trigger RSCP THD
UCELLINTERRATHOCOV InterRATMeasTime Inter-RAT Measure Timer Length
UCELLINTERRATHOCOV InterRATPingPongTimer Inter-RAT Ping-Pong Timer

UCELLINTERRATHOCOV InterRATPingPongHyst Inter-RAT Ping-Pong Hysteresis
UCELLINTERRATHOCOV PeriodFor3A 3A Event Retry Period
UCELLINTERRATHOCOV AmntOfRpt3A 3A Event Maximum Retry Times
Inter-RAT HO Physical Channel

UCELLINTERRATHOCOV InterRatPhyChFailNum Failure THD

UCELLINTERRATHOCOV PenaltyTimeForPhyChFail Failure Penalty Timer
UCELLINTERRATHONCOV CellId Cell ID
UCELLINTERRATHONCOV InterRATFilterCoef Inter-RAT Filter Coefficient

UCELLINTERRATHONCOV Hystfor3C 3C Hysteresis
UCELLINTERRATHONCOV TrigTime3C Event 3C Trigger Delay
UCELLINTERRATHONCOV BSICVerify BSIC Verify Switch

UCELLINTERRATHONCOV InterRATNCovHOCSThd THD
Inter-RAT PS Handover Decision
UCELLINTERRATHONCOV InterRATNCovHOPSThd THD
Inter-RAT Handover Max Attempt

UCELLINTERRATHONCOV InterRATHOAttempts Times
UCELLINTERRATHONCOV InterRATMeasTime Inter-RAT Measure Timer Length
UCELLINTERRATHONCOV CSHOOut2GloadThd CS Domain Reloc GSM Load THD
UCELLINTERRATHONCOV PSHOOut2GloadThd PS Domain Reloc GSM Load THD

UCELLINTERRATHONCOV PeriodFor3C Event 3C Retry Period
UCELLINTERRATHONCOV AmntOfRpt3C Event 3C Retry Max Times

UCELLINTERRATHONCOV InterRatPhyChFailNum Failure THD

UCELLINTERRATHONCOV PenaltyTimeForPhyChFail Failure Penalty Timer
UCELLINTRAFREQHO RNCId RNC ID
UCELLINTRAFREQHO CellId Cell ID
Intra-frequency L3 Filter
UCELLINTRAFREQHO IntraFreqFilterCoef Coefficient
Intra-frequency Measurement
UCELLINTRAFREQHO IntraFreqMeasQuantity Quantity
Event 1A to Periodical Report

UCELLINTRAFREQHO PeriodMRReportNumfor1A Number

UCELLINTRAFREQHO ReportIntervalfor1A Period
Event 1C to Periodical Report

UCELLINTRAFREQHO PeriodMRReportNumfor1C Number

UCELLINTRAFREQHO ReportIntervalfor1C Period
Event 1J to Periodical Report

UCELLINTRAFREQHO PeriodMRReportNumfor1J Number

UCELLINTRAFREQHO ReportIntervalfor1J Period
VP Service Event 1A Relative

UCELLINTRAFREQHO IntraRelThdFor1ACSVP Threshold
CS Non-VP Service Event 1A

UCELLINTRAFREQHO IntraRelThdFor1ACSNVP Relative THD
PS Service Event 1A Relative

UCELLINTRAFREQHO IntraRelThdFor1APS Threshold
VP Service Event 1B Relative
UCELLINTRAFREQHO IntraRelThdFor1BCSVP Threshold
CS Non-VP Service Event 1B

UCELLINTRAFREQHO IntraRelThdFor1BCSNVP Relative Threshold
PS Service Event 1B Relative

UCELLINTRAFREQHO IntraRelThdFor1BPS Threshold
Event 1F Absolute Ec/No

UCELLINTRAFREQHO IntraAblThdFor1FEcNo Threshold
Event 1F Absolute RSCP

UCELLINTRAFREQHO IntraAblThdFor1FRSCP Threshold
UCELLINTRAFREQHO HystFor1A 1A Hysteresis
UCELLINTRAFREQHO HystFor1B 1B Hysteresis
UCELLINTRAFREQHO HystFor1C 1C Hysteresis

UCELLINTRAFREQHO HystFor1D 1D Hysteresis
UCELLINTRAFREQHO HystFor1F 1F Hysteresis
UCELLINTRAFREQHO HystFor1J 1J Hysteresis
UCELLINTRAFREQHO Weight Weighted factor
UCELLINTRAFREQHO TrigTime1A Event 1A Triggering Delay

UCELLINTRAFREQHO TrigTime1B Event 1B Triggering Delay
UCELLINTRAFREQHO TrigTime1C Event 1C Triggering Delay

UCELLINTRAFREQHO TrigTime1D Event 1D Triggering Delay
UCELLINTRAFREQHO TrigTime1F Event 1F Triggering Delay

UCELLINTRAFREQHO TrigTime1J Event 1J Triggering Delay
UCELLINTRAFREQHO SHOQualmin Min Quality THD for SHO
UCELLINTRAFREQHO MaxCellInActiveSet Max Number of Cell in Active Set
Event 1F Blind Handover Trigger

UCELLINTRAFREQHO BlindHORSCP1FThreshold Condition
UCELLLDB CellId Cell ID
UCELLLDB PCPICHPowerPace Pilot power adjustment step
UCELLLDB CellOverrunThd Cell overload threshold
UCELLLDB CellUnderrunThd Cell under load threshold
UCELLLDM CellId Cell ID
UCELLLDM UlLdrTrigThd UL LDR trigger threshold

UCELLLDM UlLdrRelThd UL LDR release threshold
UCELLLDM DlLdrTrigThd DL LDR trigger threshold
UCELLLDM DlLdrRelThd DL LDR release threshold
UCELLLDM UlOlcTrigThd UL OLC trigger threshold
UCELLLDM UlOlcRelThd UL OLC release threshold
UCELLLDM DlOlcTrigThd DL OLC trigger threshold
UCELLLDM DlOlcRelThd DL OLC release threshold

DL State Trans Hysteresis
UCELLLDM DlLdTrnsHysTime threshold
HSUPA auto retransmit load
UCELLLDM HsupAuRetrnsLdTrigThd trigger threshold
HSUPA auto retransmit load
UCELLLDM HsupAuRetrnsLdRelThd release threshold
UL load restricted trigger threshold

UCELLLDM TrigRatioforUlRTWP ratio
UL load restricted release

UCELLLDM RelRatioforUlRTWP threshold ratio
UCELLLDM FairnessThd Fairness threshold
UCELLLDR CellId Cell ID

UCELLLDR DlLdrFirstAction DL LDR first action
UCELLLDR DlLdrSecondAction DL LDR second action
UCELLLDR DlLdrThirdAction DL LDR third action
UCELLLDR DlLdrFourthAction DL LDR fourth action

UCELLLDR DlLdrFifthAction DL LDR fifth action
UCELLLDR DlLdrSixthAction DL LDR sixth action
UCELLLDR DlLdrSeventhAction DL LDR seventh action
UCELLLDR DlLdrEighthAction DL LDR eighth action

UCELLLDR DlLdrNinthAction DL LDR ninth action
UCELLLDR DlLdrTenthAction DL LDR tenth action

DL LDR-BE rate reduction RAB
UCELLLDR DlLdrBERateReductionRabNum number
DL LDR un-ctrl RT Qos re-nego
UCELLLDR DlLdrPsRTQosRenegRabNum RAB num
UCELLLDR DlCSInterRatShouldBeHOUeNum DL CS should be HO user number
UCELLLDR DlPSInterRatShouldBeHOUeNum DL PS should be HO user number

DL LDR-AMR rate reduction RAB
UCELLLDR DlLdrAMRRateReductionRabNum number
DL CS should not be HO user
UCELLLDR DlCSInterRatShouldNotHOUeNum number
DL PS should not be HO user
UCELLLDR DlPSInterRatShouldNotHOUeNum number
UCELLLDR UlLdrFirstAction UL LDR first action

UCELLLDR UlLdrSecondAction UL LDR second action
UCELLLDR UlLdrThirdAction UL LDR third action
UCELLLDR UlLdrFourthAction UL LDR fourth action
UCELLLDR UlLdrFifthAction UL LDR fifth action
UCELLLDR UlLdrSixthAction UL LDR sixth action

UCELLLDR UlLdrSeventhAction UL LDR seventh action
UCELLLDR UlLdrEighthAction UL LDR eighth action

UL LDR-BE rate reduction RAB
UCELLLDR UlLdrBERateReductionRabNum number
UL LDR un-ctrl RT Qos re-nego
UCELLLDR UlLdrPsRTQosRenegRabNum RAB num
UCELLLDR UlCSInterRatShouldBeHOUeNum UL CS should be HO user number
UCELLLDR UlPSInterRatShouldBeHOUeNum UL PS should be HO user number

UL LDR-AMR rate reduction RAB
UCELLLDR UlLdrAMRRateReductionRabNum number
UL CS should not be HO user
UCELLLDR UlCSInterRatShouldNotHOUeNum number
UL PS should not be HO user
UCELLLDR UlPSInterRatShouldNotHOUeNum number
UCELLLDR UlInterFreqHoCellLoadSpaceThd UL HO load space threshold
UCELLLDR DlInterFreqHoCellLoadSpaceThd DL HO load space threshold
UCELLLDR UlInterFreqHoBWThd UL HO maximum bandwidth
UCELLLDR DlInterFreqHoBWThd DL HO maximum bandwidth

MBMS descend power rab
UCELLLDR MbmsDecPowerRabThd threshold
UCELLLDR CellLdrSfResThd Cell LDR SF reserved threshold
UCELLLDR LdrCodePriUseInd LDR code priority indicator
UCELLLDR MaxUserNumCodeAdj Max user number of code adjust
Ul LDR credit SF reserved

UCELLLDR UlLdrCreditSfResThd threshold
Dl LDR credit SF reserved

UCELLLDR DlLdrCreditSfResThd threshold
InterFreq HO code used ratio

UCELLLDR LdrCodeUsedSpaceThd space threshold
Code congestion select inter-freq

UCELLLDR CodeCongSelInterFreqHoInd indication
UCELLLDR GoldUserLoadControlSwitch Gold user load control switch
Forbidden Traffic Class for inter-

UCELLLDR InterFreqLdHoForbidenTC freq HO
Ul TTI HO Credit SF reserved

UCELLLDR UlTtiCreditSfResThd threshold
InterFreq Load Handover Method
UCELLLDR InterFreqLDHOMethodSelection Selection
UCELLLICENSE CellId Cell ID
UCELLLICENSE FuncSwitch1 Function Switch1

UCELLMBDRINTERFREQ CellId Cell ID
UCELLMBDRINTERFREQ InterFreqActiveType MBDR Switch
UCELLMBDRINTERFREQ InterFreqUlMbdrTrigThreshold UL Theshold
UCELLMBDRINTERFREQ InterFreqDlMbdrTrigThreshold DL Theshold

UCELLMBDRINTERFREQ InterFreqFilterCoef Coeff

UCELLMBDRINTERFREQ InterFreqReportMode Mode
UCELLMBDRINTERFREQ InterFreqMeasQuantity Inter-freq Measure Quantity

UCELLMBDRINTERFREQ PrdReportInterval Period
UCELLMBDRINTERFREQ TimeToTrigForPrdInterFreq HHO Period Trigger Delay
UCELLMBDRINTERFREQ HystForPrdInterFreq HHO Hysteresis
UCELLMBDRINTERFREQ Hystfor2C 2C Hysteresis
UCELLMBDRINTERFREQ TrigTime2C Event 2C Trigger Delay
Inter-freq measure target

UCELLMBDRINTERFREQ HOThdEcN0 frequency trigger Ec/No THD

UCELLMBDRINTERFREQ HOThdRscp frequency trigger RSCP THD
Inter-Freq DRD Max Attempt

UCELLMBDRINTERFREQ MaxAttNum Times
UCELLMBDRINTERFREQ InterFreqMeasTime Inter-freq Measure Timer Length
UCELLMBDRINTERRAT CellId Cell ID
UCELLMBDRINTERRAT InterRatActiveType MBDR switch
UCELLMBDRINTERRAT InterRatUlMbdrTrigThreshold UL Theshold
UCELLMBDRINTERRAT InterRatDlMbdrTrigThreshold DL Theshold
UCELLMBDRINTERRAT InterRATFilterCoef Inter-RAT Filter Coefficient
UCELLMBDRINTERRAT InterRatReportMode Inter-RAT Report Mode

UCELLMBDRINTERRAT InterRATPeriodReportInterval Interval
UCELLMBDRINTERRAT BSICVerify BSIC Verify Switch

UCELLMBDRINTERRAT TimeToTrigForNonVerify Verified GSM Cell

UCELLMBDRINTERRAT TimeToTrigForVerify Verified GSM Cell
UCELLMBDRINTERRAT Hystfor3C 3C Hysteresis
UCELLMBDRINTERRAT TrigTime3C Event 3C Trigger Delay

UCELLMBDRINTERRAT InterRATHOThd THD
Inter-RAT DRD Max Attempt

UCELLMBDRINTERRAT MaxAttNum Times
UCELLMBDRINTERRAT UserPercentage UserPercentage
UCELLMBDRINTERRAT InterRATMeasTime Inter-RAT Measure Timer Length
UCELLMBDRINTERRAT PenaltyTimer Inter-RAT Penalty timer length
UCELLMBMSFACH CellId Cell ID
UCELLMBMSFACH ServiceType Service Type
UCELLMBMSFACH ServiceBitRate Service Bit Rate
UCELLMBMSFACH FachMaxPower Fach Max Power
Mtch Minimal Power Percent for

UCELLMBMSFACH MtchMinPerc0 Priority 0

UCELLMBMSFACH MtchMinPerc15 Priority 15
UCELLMBMSFACH ToAWS Time of Arrival Window Startpoint
UCELLMBMSFACH ToAWE Time of Arrival Window Endpoint
UCELLMBMSPARA CellId Cell ID
UCELLMBMSPARA MbmsTransMode Mbms Transfer Mode

UCELLMBMSPARA NCountingThd Counting Threshold
UCELLMBMSPARA NPtpToPtmOffset Ptp To Ptm Offset
UCELLMBMSSA CellId Cell ID
UCELLMBMSSA CnOpIndex Cn Operator Index
UCELLMBMSSA MbmsSaId MBMS SA ID
UCELLMBMSSCCPCH CellId Cell ID
UCELLMBMSSCCPCH ServiceType Service Type
UCELLMBMSSCCPCH ServiceBitRate Service Bit Rate
UCELLMBMSSCCPCH STTDInd STTD Indicator
UCELLMCCH CellId Cell ID

UCELLMCCH MichId MICH ID
UCELLMCCH MichPower MICH Power
UCELLMCCH MichSttdInd MICH STTD Indicator
UCELLMCCH PhyChIdforMcch SCCPCH ID for MCCH
UCELLMCCH FachIdforMcch FACH ID for MCCH
UCELLMCCH FlcAlgoSwitch Flc Algo Switch
UCELLMCDRD CellId Cell ID
UCELLMCDRD BlindDrdExceptHRetrySwitch Aperiodic DRD Retry Switch
DRD Measurement Period Retry

UCELLMCDRD HRetryTimerLength Timer Length
Inter-Frequency Periodic
UCELLMCDRD PrdReportInterval Measurement Report Interval
Target Frequency RSCP Trigger
UCELLMCDRD TargetFreqThdRscp Threshold
Target Frequency EcNo Trigger

UCELLMCDRD TargetFreqThdEcN0 Threshold
DRD Measurement Failure Punish

UCELLMCDRD DrdFaiPenaltyPeriodNum Periods
UCELLMCLDR CellId Cell ID
UCELLMCLDR InterFreqMeasTime Inter-freq Measure Timer Length
Inter-freq Measure Periodical

UCELLMCLDR PrdReportInterval Report Period
Inter-freq Target Frequency
UCELLMCLDR TargetFreqThdRscp Trigger RSCP THD
UCELLMCLDR TargetFreqThdEcN0 Trigger Ec/No THD
UCELLMEAS CellId Cell ID
UCELLMEAS IntraFreqMeasInd Intra-freq Meas Ctrl Info Ind
Inter-freq and Inter-RAT Meas Ctrl

UCELLMEAS InterFreqInterRatMeasInd Info Ind
UCELLMEAS FACHMeasInd FACH Measurement Indicator
UCELLNAME RNCId RNC ID
UCELLNAME CellId Cell ID
UCELLNAME CellName Cell Name
UCELLNCLUSTER CellId Cell ID
UCELLNCLUSTER NClusterId Neighboring Cluster ID
UCELLNFREQPRIOINFO CellId Cell ID
E-UTRA Absolute Radio

UCELLNFREQPRIOINFO EARFCN Frequency Channel Number
Absolute Priority Level of the E-
UCELLNFREQPRIOINFO NPriority UTRA Frequency
RSRP Threshold for High-prio-freq

UCELLNFREQPRIOINFO ThdToHigh Reselection
RSRP Threshold for Low-prio-freq

UCELLNFREQPRIOINFO ThdToLow Reselection
UCELLNFREQPRIOINFO EMeasBW Measurement Bandwidth
Minimum Required RSRP

UCELLNFREQPRIOINFO EQrxlevmin Threshold of the E-UTRA Cell
UCELLNFREQPRIOINFO EDetectInd E-UTRA Monitoring Indication
Number of Cells in the Blacklist of

UCELLNFREQPRIOINFO BlacklstCellNumber the E-UTRA Frequency
UCELLNFREQPRIOINFO BCellID1 ID of Cell 1 in the Blacklist


UCELLOLC CellId Cell ID
UCELLOLC DlOlcFTFRstrctTimes DL OLC fast TF restrict times

UCELLOLC UlOlcFTFRstrctTimes UL OLC fast TF restrict times
DL OLC fast TF restrict RAB

UCELLOLC DlOlcFTFRstrctRabNum number
UL OLC fast TF restrict RAB

UCELLOLC UlOlcFTFRstrctRabNum number
UCELLOLC RateRstrctCoef DL TF rate restrict coefficient
UCELLOLC RecoverCoef DL TF rate recover coefficient
UCELLOLC RateRstrctTimerLen DL TF rate restrict timer length
UCELLOLC RateRecoverTimerLen DL TF rate recover timer length
UCELLOLC DlOlcTraffRelRabNum DL OLC traff release RAB number
UCELLOLC UlOlcTraffRelRabNum UL OLC traff release RAB number
UCELLOLC SeqOfUserRel Sequence of user release
UCELLOLC MbmsOlcRelNum MBMS services number released
Transfer Common Channel User

UCELLOLC TransCchUserNum number
UCELLOLC FACHPwrReduceValue Fach power reduce value
UCELLPUC CellId Cell ID
UCELLPUC SpucLight Load level division threshold 2

UCELLPUC SpucHeavy Load level division threshold 1
UCELLPUC SpucHyst Load level division hysteresis
UCELLPUC OffSinterLight Sintersearch offset 1
UCELLPUC OffSinterHeavy Sintersearch offset 2
UCELLPUC OffQoffset1Light Qoffset1 offset 1
UCELLPUC OffQoffset2Light Qoffset2 offset 1
UCELLPUC OffQoffset1Heavy Qoffset1 offset 2
UCELLPUC OffQoffset2Heavy Qoffset2 offset 2
UCELLQOSHO CellId Cell ID
Down Link RSCP Used-Freq THD

UCELLQOSHO DlRscpQosHyst Hyst
Down Link QoS Measure Timer

UCELLQOSHO DLQosMcTimerLen Length
Up Link QoS Measure Timer

UCELLQOSHO ULQosMcTimerLen Length
3A Used-Freq Measure Quantity

UCELLQOSHO UsedFreqMeasQuantityForQos3A for QoS
UCELLQUALITYMEAS CellId Cell ID
UCELLQUALITYMEAS UlAmrTrigTime6A1 AMR Trigger Time 6A1
UCELLQUALITYMEAS UlAmrTrigTime6A2 AMR Trigger Time 6A2
UCELLQUALITYMEAS UlAmrTrigTime6B1 AMR Trigger Time 6B1
UCELLQUALITYMEAS UlAmrTrigTime6B2 AMR Trigger Time 6B2
UCELLQUALITYMEAS UlAmrTrigTime6D AMR Trigger Time 6D
UCELLQUALITYMEAS UlVpTrigTime6A1 VP Trigger Time 6A1
UCELLQUALITYMEAS UlVpTrigTime6B1 VP Trigger Time 6B1
UCELLQUALITYMEAS UlVpTrigTime6D VP Trigger Time 6D
UCELLQUALITYMEAS UlBeTrigTime6A1 BE Trigger Time 6A1
UCELLQUALITYMEAS UlBeTrigTime6B1 BE Trigger Time 6B1
UCELLQUALITYMEAS UlBeTrigTime6A2 BE Trigger Time 6A2

UCELLQUALITYMEAS UlBeTrigTime6B2 BE Trigger Time 6B2
UCELLQUALITYMEAS UlBeTrigTime6D BE Trigger Time 6D
UCELLQUALITYMEAS UlMeasFilterCoef UL Measurement Filter Coefficient
DL TCP Measurement Filter

UCELLQUALITYMEAS DlMeasFilterCoef Coefficient
UCELLQUALITYMEAS DlAmrTrigTimeE AMR Trigger Time of Event E
AMR Reporting Period Unit for

UCELLQUALITYMEAS ChoiceRptUnitForAmrE Event E
UCELLQUALITYMEAS TenMsecForAmrE AMR Event E Reporting Period
AMR Event E Reporting Period

UCELLQUALITYMEAS MinForAmrE minute
UCELLQUALITYMEAS DlVpTrigTimeE VP Trigger Time of Event E
VP Reporting Period Unit for Event

UCELLQUALITYMEAS ChoiceRptUnitForVpE E
UCELLQUALITYMEAS TenMsecForVpE VP Event E Reporting Period
VP Event E Reporting Period

UCELLQUALITYMEAS MinForVpE minute
UCELLQUALITYMEAS DlBeTrigTimeE BE Trigger Time of Event E
BE Reporting Period Unit for Event

UCELLQUALITYMEAS ChoiceRptUnitForBeE E
UCELLQUALITYMEAS TenMsecForBeE BE Event E Reporting Period
BE Event E Reporting Period

UCELLQUALITYMEAS MinForBeE minute
UCELLQUALITYMEAS DlBeTrigTimeF BE Trigger Time of Event F

UCELLQUALITYMEAS ChoiceRptUnitForBeF F
UCELLQUALITYMEAS TenMsecForBeF BE Event F Reporting Period
BE Event F Reporting Period

UCELLQUALITYMEAS MinForBeF minute
UCELLREDIRECTION CellId Cell ID
UCELLREDIRECTION TrafficType Traffic class
UCELLREDIRECTION RedirSwitch Redirection Switch

UCELLREDIRECTION RedirFactorOfNorm Redirection Factor Of Normal
UCELLREDIRECTION RedirFactorOfLDR Redirection Factor Of LDR
UCELLREDIRECTION RedirBandInd ReDirection target band indicator

UCELLREDIRECTION ReDirUARFCNUplinkInd Index
UCELLREDIRECTION ReDirUARFCNUplink Redirection target uplink UARFCN

UCELLREDIRECTION ReDirUARFCNDownlink UARFCN
UCELLRLACTTIME CellId Cell ID
UCELLRLACTTIME CellId Cell ID
UCELLRLPWR CellId Cell ID
UCELLRLPWR CNDomainId CN domain ID
UCELLRLPWR MaxBitRate Max bit rate of service
UCELLRLPWR RlMaxDlPwr RL Max DL TX power
UCELLRLPWR RlMinDlPwr RL Min DL TX power
UCELLRLPWR DlSF Downlink spreading factor
UCELLSELRESEL CellId Cell ID

Cell Sel-reselection quality
UCELLSELRESEL QualMeas measure
UCELLSELRESEL IdleQhyst1s Hysteresis 1 for idle mode
UCELLSELRESEL ConnQhyst1s Hysteresis 1 for connect mode

UCELLSELRESEL IdleQhyst2s Hysteresis 2 for idle mode
UCELLSELRESEL ConnQhyst2s Hysteresis 2 for connect mode
UCELLSELRESEL Treselections Reselection delay time
UCELLSELRESEL Qqualmin Min quality level
UCELLSELRESEL Qrxlevmin Min Rx level
UCELLSELRESEL QrxlevminExtSup Min Rx level Extend Support
UCELLSELRESEL DeltaQrxlevmin Delta Min Rx level
UCELLSELRESEL MaxAllowedUlTxPower Max allowed UE UL TX power
Intra-freq cell reselection threshold

UCELLSELRESEL IdleSintrasearch for idle mode
Inter-freq cell reselection threshold

UCELLSELRESEL IdleSintersearch for idle mode
Intra-freq cell reselection threshold

UCELLSELRESEL ConnSintrasearch for connect mode
Inter-freq cell reselection threshold

UCELLSELRESEL ConnSintersearch for connect mode
Inter-RAT cell reselection
UCELLSELRESEL SsearchRat threshold
Speed dependent scaling factor
UCELLSELRESEL SpeedDependentScalingFactor for reselection delay
Inter-freqency scaling factor for
UCELLSELRESEL InterFreqTreselScalingFactor reselection delay
Inter-RAT scaling factor for
UCELLSELRESEL InterRatTreselScalingFactor reselection delay
UCELLSELRESEL NonhcsInd Non-HCS indicator
UCELLSELRESEL Tcrmaxnonhcs Non-HCS max TCR
UCELLSELRESEL Ncrnonhcs Non-HCS NCR
UCELLSELRESEL Tcrmaxhystnonhcs Non-HCS TCR max hysteresis
Hysteresis 1 for UE in CELL_PCH

UCELLSELRESEL Qhyst1spch or URA_PCH state
Hysteresis 1for UE in CELL_FACH
UCELLSELRESEL Qhyst1sfach state
Hysteresis 2 for UE in CELL_PCH

UCELLSELRESEL Qhyst2spch or URA_PCH state
Hysteresis 2 for UE in
UCELLSELRESEL Qhyst2sfach CELL_FACH state
Reselection delay time for UE in
UCELLSELRESEL Treselectionspch PCH state
Reselection delay time for UE in
UCELLSELRESEL Treselectionsfach CELL_FACH state
Absolute priority level of the

UCELLSELRESEL SPriority serving cell
RSCP threshold for low-prio-freq

UCELLSELRESEL ThdPrioritySearch1 measurement initiation
Ec/No threshold for low-prio-freq
UCELLSELRESEL ThdPrioritySearch2 measurement initiation
RSCP threshold for low-prio-freq

UCELLSELRESEL ThdServingLow reselection
UCELLSIBSWITCH CellId Cell ID
UCELLSIBSWITCH SibCfgBitMap SIB Switch
UCELLU2LTEHONCOV CellId Cell ID
UCELLU2LTEHONCOV LTEMeasTypOf3C Report Type of LTE Measurement
Layer 3 Filter Coefficient for LTE

UCELLU2LTEHONCOV U2LTEFilterCoef Measurement
UCELLU2LTEHONCOV U2LTEMeasTime LTE Measurement Timer Length
Measurement Quantity for Event

UCELLU2LTEHONCOV LTEMeasQuanOf3C 3C Measurement of LTE
UCELLU2LTEHONCOV Hystfor3C Hysteresis for Event 3C
UCELLU2LTEHONCOV TrigTime3C Time to Trigger Event 3C
RSRP Threshold During PS

UCELLU2LTEHONCOV TargetRatThdRSRP Handover to LTE
RSRQ Threshold During PS

UCELLU2LTEHONCOV TargetRatThdRSRQ Handover to LTE
UCELLULB CellId Cell ID
UCELLULB RTWPHeavyThd RTWP Heavy Threshold
UCELLULB RTWPLightThd RTWP Light Threshold
UCELLULB PCPICHPowerPace CPICH Power Adjustment Pace
UCELLURA CellId Cell ID

UCELLURA URAId URA ID
UCHGTHRSHOLD CnOpIndex Cn Operator Index
UCHGTHRSHOLD Gvcl G-CDR Flow Threshold

Maximum number of charging
UCHGTHRSHOLD Gccl condition changes
UCHGTHRSHOLD Threshold G-CDR Time Threshold
UCHGTHRSHOLD RsvdPara1 Reserved Parameter1
UCHPWROFFSET CellId Cell ID
UCHPWROFFSET PICHPowerOffset PICH Power Offset

UCHPWROFFSET AICHPowerOffset AICH Power Offset
UCHRCTRL StateType State Type
UCHRCTRL DomainType Domain Type
UCHRCTRL FlowType Flow Type
RRC Connection Establishment

UCHRCTRL RRCCause Cause
UCHRSCOPE ScopeType Scope Type
UCHRSCOPE SRN Subrack No.

UCHRSCOPE SN Slot No.
UCHRSCOPE SSN Subsystem No.
UCHRSCOPE NodeBId NodeB ID
UCHRSCOPE CellId Cell ID
UCHRSCOPE CHRScopeCtrl CHR Scope Control Switch
UCIDCHG CellIDChgSwitch Cell ID Changing Switch

Cell ID Changing Period time
UCIDCHG CellIDChgPeriod length
UCMCF DeltaCFN Delta CFN to Start CM Mode
UCMCF DlSFTurnPoint DL SF Threshold
UCMCF UlSFTurnPoint UL SF threshold
UCMCF CmcfCellType CM Cell Type
UCMCF DlSFLimitCMInd Dl SF Limit CM Ind
UCMCF LimitCMDlSFThd Dl SF Threshold to Limit CM

UCMCF HsdpaCMPermissionInd CM Permission Ind on HSDPA
UCMCF HsupaCMPermissionInd CM Permission Ind on HSUPA
UCMCF EHSPACMPermissionInd CM Permission Ind on HSPA+
UCNDOMAIN CNDomainId CN domain ID
UCNDOMAIN T3212 Periodical location update timer
UCNDOMAIN ATT Attach/detach allowed indication
UCNDOMAIN NMO Network mode of operation
UCNDOMAIN DRXCycleLenCoef DRX cycle length coefficient

UCNNODE CnOpIndex Cn Operator Index
UCNNODE CNId CN node ID
UCNNODE CNDomainId CN domain ID
UCNNODE Dpx DSP index
UCNNODE CNProtclVer CN protocol version
UCNNODE SupportCRType CR support type
UCNNODE CNLoadStatus Status of CN Node
UCNNODE AvailCap Capability of CN Node

UCNNODE TnlBearerType Iu transfers bearer type
UCNNODE RTCPSwitch RTCP SWITCH
UCNNODE RTCPBWRatio RATE OF RTCP BANDWIDTH
UCNNODE Switch3GPP25415CR0125 Switch3GPP25415CR0125
UCNNODE RsvdPara1 Reserved parameter 1
Downlink E2EQoS Algorithm

UCNNODE DLE2EQoSSwitch Switch
UCNOPALLCELLBLK CnOpIndex Cn Operator Index
UCNOPALLCELLBLK DomainType Blocked Domain Type

UCNOPALLCELLBLK ProcessDuration Processing Duration
UCNOPERATOR OperatorType Operator Type
UCNOPERATOR CnOperatorName Cn Operator Name
UCNOPERATOR MCC MCC
UCNOPERATOR MNC MNC
UCNOPERATOR CnOpIndex Cn Operator Index
UCNOPERGROUP CnOpGrpIndex Cn Operator Group Index
UCNOPERGROUP CnOpGrpName Cn Operator Group Name
UCNOPERGROUP CnOpNum Operator Number
UCNOPERGROUP CnOpIndex1 Operator 1 Index

UCNOPERGROUP CnOpIndexComm Common Operator Index
UCNTCHK CounterCheckSwitch Counter check switch
UCNTCHK CountCThreshold Count-C threshold

Release 0 kbit/s Timer Length for
UCOIFTIMER ZeroRateUpFailToRelTimerLen Failed to Rate Up
UCOIFTIMER ChannelRetryTimerLen Channel Retry Timer Length
UCOIFTIMER ChannelRetryHoTimerLen Channel Retry Ho Timer Length
UCOIFTIMER RabModifyTimerLen Rab Modify Timer Length

Punishment Timer for HSUPA
UCOIFTIMER AdapRetranPunTimer Adaptive Retrans
UCONNMODETIMER T302 Timer 302
UCONNMODETIMER N302 Constant 302

Channel Configuration Strategy

UCORRMALGOSWITCH CfgSwitch Switch
Dynamic Resource Allocation
UCORRMALGOSWITCH DraSwitch Switch
UCORRMALGOSWITCH CsSwitch CS Algorithm Switch
UCORRMALGOSWITCH PcSwitch Power Control Switch

UCORRMALGOSWITCH CmpSwitch Compatibility Switch
UCORRMALGOSWITCH MapSwitch Service Mapping Strategy Switch

UCORRMALGOSWITCH PsSwitch PS Rate Negotiation Switch
UCORRMALGOSWITCH DrSwitch Direct Retry Switch
UCORRMALGOSWITCH HoSwitch HandOver Switch

UCORRMALGOSWITCH SrnsrSwitch SRNSR Algorithm Switch
UCORRMALGOSWITCH CmcfSwitch CMCF Algorithm Switch

CORRM Algorithm Reserved
UCORRMALGOSWITCH ReservedSwitch0 Switch 0
UCORRMALGOSWITCH ReservedSwitch1 Switch 1
CORRM Algorithm Reserved U32

UCORRMALGOSWITCH ReservedU32Para0 Para 0


UCORRMALGOSWITCH CmpSwitch2 Compatibility Switch2
UCORRMPARA PerfEnhanceSwitch Performance Enhancement Switch

UCORRMPARA ReservedSwitch0 Switch 0
UCORRMPARA ReservedSwitch1 Switch 1
UCORRMPARA ReservedU32Para0 Para 0
UCPUSSHARETHD CPUSShareThd CPUS Traffic Share Threshold
UCTCH CellId Cell ID
UCTCH FachId FACH ID
UCTRLPLNFCPARA RanCtrlFcSwitch Control Plane Flow Control switch

Congestion Level from others to
UCTRLPLNFCPARA AllToLow low rate
UCTRLPLNFCPARA HighToHigh high to high control rate
UCTRLPLNFCPARA OverToOver Overload to Overload Rate
UCTRLPLNFCPARA LowToMidToHighToOver Congestion Level Rises Rate
UCTRLPLNFCPARA OverToHighToMid Congestion Level Descends Rate
Control Plane Sharing Out

UCTRLPLNSHAREPARA CtrlPlnSharingOutThd Threshold
UCTRLPLNSHAREPARA CtrlPlnSharingOutOffset Control Plane Sharing Out Offset
UCTRLPLNSHAREPARA MaxCAPSMidLoad Max Capability Middle Load
Sharing Out Capability Middle

UCTRLPLNSHAREPARA SharingOutCAPSMidLoad Load
UCTRLPLNSHAREPARA MaxCAPSLowLoad Max Capability Normal Load
UCZ CnOpIndex Cn Operator Index
UCZ LAC Location Area Code
UCZ SAC Service Area Code
UCZ CZ Classified Zone ID

Uplink Bit Rate Threshold for
UDCCC UlDcccRateThd DCCC
Downlink Bit Rate Threshold for
UDCCC DlDcccRateThd DCCC
UDCCC LittleRateThd Low Activity Bit Rate Threshold
UDCCC DcccStg DCCC Strategy
UDCCC HsupaDcccStg HSUPA DCCC Strategy

BE Event F Reporting Power
UDCCC BePwrMargin Margin
Comb Event F Reporting Power
UDCCC CombPwrMargin Margin
UDCCC UlRateUpAdjLevel Uplink Rate Increase Adjust Level
UDCCC UlRateDnAdjLevel Uplink Rate Decrease Adjust Level

Uplink Mid Bit Rate Calculate
UDCCC UlMidRateCalc Method
UDCCC UlMidRateThd Uplink Mid Bit Rate Threshold

Downlink Rate Increase Adjust
UDCCC DlRateUpAdjLevel Level
Downlink Rate Decrease Adjust
UDCCC DlRateDnAdjLevel Level
Downlink Mid Bit Rate Calculate
UDCCC DlMidRateCalc Method
UDCCC DlMidRateThd Downlink Mid Bit Rate Threshold

DCCC Rate Up Fail Time
UDCCC FailTimeTh Threshold
DCCC Rate Up Fail Monitor Time
UDCCC MoniTimeLen length
DCCC Rate Up Fail Penalty Time
UDCCC DcccUpPenaltyLen Length
UDCCC UlFullCvrRate Uplink Full Coverage Bit Rate
UDCCC DlFullCvrRate Downlink Full Coverage Bit Rate
UDCCC DchThrouMeasPeriod DCH Throu Meas Period
UDCCC HsupaBeShoRateThd HSUPA BE SHO THD RATE

Event 4B Threshold for E-DCH-to-
UDCCC E2DThrou4BThd DCH Channel Switch
UDEVICETYPEIMSI IMSISegIndex Index of IMSI Number Segment

IMSI Number Segment
UDEVICETYPEIMSI IMSISegChoice Configuration Mode
UDEVICETYPEIMSI IMSIStart Start of IMSI Number Segment
UDEVICETYPEIMSI IMSIEnd End of IMSI Number Segment
UDEVICETYPEIMSI IMSISelected IMSI Filter Character

Fixed Value in IMSI Number
UDEVICETYPEIMSI IMSIFixed Segment
UDEVICETYPEPRIOGROUP DPGId Hierarchy ID of Terminal Type
UDEVICETYPEPRIOGROUP UEDP UE Hierarchy Priority
UDEVICETYPEPRIOGROUP DataCardDP Data Card Hierarchy Priority
UDEVICETYPEPRIOGROUP ReservedDP Reserved Parameter
UDISTANCEREDIRECTION RedirSwitch Redirection Switch
UDISTANCEREDIRECTION DelayThs Propagation delay threshold
UDISTANCEREDIRECTION RedirFactorOfLDR Redirection Factor Of LDR
UDISTANCEREDIRECTION RedirFactorOfNorm Redirection Factor Of Normal

First Macro Diversity Combination
UDPUCFGDATA FpmdcCombineDelayValue Delay
Iub FP Protect Time of Trans
UDPUCFGDATA IubFpTwaittrchsyncrsp Channel Syn
Protect Time of Iub FP for Node
UDPUCFGDATA IubFpTwaitnodesyncrsp Syn
Iur FP Protect Time of Trans
UDPUCFGDATA IurFpTwaittrchsyncrsp Channel Syn
Protect Time of Iur FP for Node
UDPUCFGDATA IurFpTwaitnodesyncrsp Syn
UDPUCFGDATA TimeAlignSwitch Time Adjustment Switch

Frame Loss Ratio Thres of Iub E-
UDPUCFGDATA EdchIubCongLossRatioThd DCH Cong
Iub E-DCH Congestion Check
UDPUCFGDATA EdchIubCongCheckSwitch Switch
UDPUCFGDATA CRCCheckSwitch CRC Check Switch

Switch Of DL R99 Congestion
UDPUCFGDATA DlR99CongCtrlSwitch Control
Congestion Thres of Packet Loss
UDPUCFGDATA PacketLossRatioThld Ratio
Congestion Thres of Lost Packet
UDPUCFGDATA PacketLossNumThld Number
Iur HSUPA Congestion Control
UDPUCFGDATA HsupaIurCongCtrlSwitch Switch
Congestion Delay Thres in UL
UDPUCFGDATA TnlLatencyThld Trans Layer
PacketLossRatio Thres in UL
UDPUCFGDATA TnlPacketLossRatioThld Trans Layer
Lost Packet Num Thres In UL
UDPUCFGDATA TnlPacketLossNumThld Trans Layer
Lost Packet Num Thres2 In UL
UDPUCFGDATA TnlPacketLossNumThld2 Trans Layer
UDPUCFGDATA TpeSwitch TPE Switch
UDPUCFGDATA SpiWeightAdjPeriod SPI Weight Adjustment Period

Service Priority Adjusting
UDPUCFGDATA ServicePriAdjCoef Coefficient
UDPUCFGDATA SpiWeiStrategyFactor SPI Weight Adjust Strategy Factor

Max Interval of SPI Weight Adjust
UDPUCFGDATA MaxAdjPeriodCoef Factor
UDPUCFGDATA R99TnlSwitch R99 Congestion Control Switch
UDPUCFGDATA HsupaTnlSwitch HSUPA Congestion Control Switch
UDPUCFGDATA CellCountersMeasOBJCtrlSwitch Performance Measurement Switch

UDPUCFGDATA AntiDDoSThs Anti-DDoS Flow Control Threshold
UDPUCFGDATA AntiSpfThs Anti-spoofing Threshold
Scheduling Priority Weight for High

UDPUCFGDATA ServPriAdjCoefHigh PRI Service
Scheduling Priority Weight for

UDPUCFGDATA ServPriAdjCoefMiddle Middle PRI Service
Scheduling Priority Weight for Low

UDPUCFGDATA ServPriAdjCoefLow PRI Service
RAB PDP Alive Detect Timer
UDPUCFGDATA OffloadAliveDetectPeriod Length of Offload User
RAB Keep Alive Timer Length of
UDPUCFGDATA OffloadAliveKeepPeriod Offload User
UDPUCFGDATA FachCongThd FACH Congestion Threshold

FACH Congestion Recovery
UDPUCFGDATA FachCongRecoverThd Threshold
FACH Congestion Clearing
UDPUCFGDATA FachCongClearThd Threshold
Switch of Auto ACK Construct in
UDPUCFGDATA TcpAutoAckSwitch TCP Mode
UDPUCFGDATA DrdRollBackSwitch DRD Rollback Switch
UDPUCFGDATA HspaTrafficTimeSwitch HSDPA Data Sending Time Switch
UDPUCFGDATA PagingSwitch Paging Preemption Switch

Silence Detection and Tracing
UDPUCFGDATA SilentTraceSwitch Switch
UDPUCFGDATA AmrNoiseCorrectSwitch AMR Noise Change Switch
UDPUCFGDATA TpeEnhanceSwitch TPE Multi-Threading Switch
UDPUCFGDATA SmartSrvSharingThd Smart Service Sharing Threshold

UDPUCFGDATA RsvdSwitch1 Reserved Switch 1
UDPUCFGDATA RsvdSwitch2 Reserved Switch 2
UDPUCFGDATA RsvdPara1 Reserved Parameter1


Maximum Times of Inter-RAT
UDRD DRMaxGSMNum Direct Retry
UDRD ServiceDiffDrdSwitch Service Steering DRD Switch
UDRD LdbDRDSwitchDCH Load balance DRD switch for DCH
Load balance DRD switch for

UDRD LdbDRDSwitchHSDPA HSDPA
UDRD LdbDRDchoice Load Balancing DRD Choice
RRC Redirection Switch for

UDRD ConnectFailRrcRedirSwitch Admission Failure
UDRD LdbDRDOffsetDCH Load balance DRD offset for DCH

Load balance DRD offset for
UDRD LdbDRDOffsetHSDPA HSDPA
UDRD LdbDRDLoadRemainThdDCH remain threshold for DCH
UDRD LdbDRDLoadRemainThdHSDPA remain threshold for HSDPA
Load balance DRD total power
UDRD LdbDRDTotalPwrProThd protect threshold
UDRD CodeBalancingDrdSwitch Code Balancing DRD Switch
UDRD DeltaCodeOccupiedRate Delta of Code Occupancy

Minimum SF Threshold for Code
UDRD CodeBalancingDrdMinSFThd Balancing DRD
Code Occupancy Thres for Code
UDRD CodeBalancingDrdCodeRateThd Balancing DRD
UDRD ReDirBandInd ReDirection target band indicator

UDRD ReDirUARFCNUplinkInd Index
UDRD ReDirUARFCNUplink Redirection target uplink UARFCN

UDRD ReDirUARFCNDownlink UARFCN
Uplink load balance DRD Switch
UDRD ULLdbDRDSwitchDcHSDPA for DC-HSDPA
Uplink load balance DRD Offset
UDRD ULLdbDRDOffsetDcHSDPA for DC-HSDPA
ULLdbDRDLoadRemainThdDcHS Uplink load balance DRD remain
UDRD DPA threshold for DC-HSDPA
UDRD BasedOnMeasHRetryDRDSwitch Measurement-Based DRD Switch

UDRD DPGDRDSwitch Terminal Type Hierarchy Switch
DRD Switch for LegacyH under
UDRDMIMO LegacyHDrdSwitchOfSTTD STTD
DRD Switch for LegacyH under P
UDRDMIMO LegacyHDrdSwitchOfSCPICH and S CPICH
UDRDMIMO CQIRefValueOfSTTD CQI reference value for STTD

CQI reference value for P and S
UDRDMIMO CQIRefValueOfSCPICH CPICH
UDRDMIMO ExcellentCQIThdOfSTTD Excellent CQI Threshold for STTD
UDRDMIMO GoodCQIThdOfSTTD Good CQI Threshold for STTD
UDRDMIMO BadCQIThdOfSTTD Bad CQI Threshold for STTD

Excellent CQI Threshold for P and
UDRDMIMO ExcellentCQIThdOfSCPICH S CPICH
Good CQI Threshold for P and S
UDRDMIMO GoodCQIThdOfSCPICH CPICH
Bad CQI Threshold for P and S
UDRDMIMO BadCQIThdOfSCPICH CPICH
CQI Measurement Filter

UDRDMIMO CQIMeasFilterCoef Coefficient
UDRDMIMO CQITrigTimeE CQI Trigger Time Of Event E

CQI Reporting Period Unit For
UDRDMIMO ChoiceRptUnitForCQIE Event E
CQI Event E Reporting Period In
UDRDMIMO TenMsecForCQIE 10ms
CQI Event E Reporting Period In
UDRDMIMO MinForCQIE Minute
UDRDMIMO CQITrigTimeF CQI Trigger Time Of Event F

CQI Reporting Period Unit For
UDRDMIMO ChoiceRptUnitForCQIF Event F
CQI Event F Reporting Period In
UDRDMIMO TenMsecForCQIF 10ms
CQI Event F Reporting Period In
UDRDMIMO MinForCQIF Minute
UDSACAUTOALGO DsacAutoSwitch Switch for auto DSAC
UDSACAUTOALGO CsRestriction Restriction for CS
UDSACAUTOALGO PsRestriction Restriction for PS

Number of restrained Access
UDSACAUTOALGO NumberOfACs Class every time
UDSACAUTOALGO AcRange Range of restrained Access Class
Access Class Restriction interval
UDSACAUTOALGO AcIntervalOfCells between Cells
Interval length of Domain Specific
UDSACAUTOALGO AcRstrctIntervalLen Access Class Restriction
DSS Dea Inter-Freq HO Protection

UDSSPARA DeaDSSInterFreqHOTimer Duration
DSS Dea Inter-RAT HO Protection

UDSSPARA DeaDSSInterRATHOTimer Duration
HO Period at a Spectrum
UDSSPARA DeaDSSHOPeriodTimer Withdrawal
HO UE Threshold at a Spectrum
UDSSPARA DeaDSSPeriodHOUserNumThrd Withdrawal
Urgent DSS Dea Inter-Freq HO
UDSSPARA UrgentDeaDSSHOTimer Duration
UDTXDRXPARA TrafficClass Traffic class
UDTXDRXPARA EdchTtiType Edch TTI type
UDTXDRXPARA Dtxvalid DTX Parameter Switch

Threshold For DPCCH
UDTXDRXPARA InactThsForCycle2 Transmission Cycle 2
Number of Preamble Timeslots in
UDTXDRXPARA DtxLongPreamble the Case of DtxCycle2
UDTXDRXPARA MacInactiveThreshold MAC Inactivity Threshold
UDTXDRXPARA CqiDtxTimer CQI Activity Timer
UDTXDRXPARA DpcchBurst1 DPCCH Transmission Burst 1
UDTXDRXPARA DpcchBurst2 DPCCH Transmission Burst 2
UDTXDRXPARA Drxvalid DRX Parameter Switch

UDTXDRXPARA DrxCycle DRX Cycle
UDTXDRXPARA InactThsForDrxCycle DRX Inactivity Threshold

Inactivity Threshold for UE Grant
UDTXDRXPARA InactThsForGrantMonitoring Monitoring
UE DRX Grant Monitoring
UDTXDRXPARA DrxGrantMonitoring Decision
CQI Feedback Cycke in DTX-DRX
UDTXDRXPARA CQIFbCkinInDTXDRXmode mode
UDTXDRXPARA DtxCycle1 DPCCH Transmission Cycle 1
UDTXDRXPARA DtxCycle2 DPCCH Transmission Cycle 2
UDTXDRXPARA MacDtxCycle MAC Transmission Cycle
Traffic Priority Mapping DSCP

UE2EQOSPARA DSCP0TrafficPri Value 0

























































UEDCHRATEADJUSTSET EdchRateAdjustSet HSUPA UpLink Rate Adjust Set
HSUPA Voice Packet Missing
UEDCHTTIRECFG VoicePmrMcSwitch Ratio Measurement Switch
Highest User Priority Guarantee
UEDCHTTIRECFG PriorityOpt Option
Event A Triggering Threshold for
UEDCHTTIRECFG AmrEventAThd AMR
Event 6A1 Relative Threshold for
UEDCHTTIRECFG AmrThd6A1 AMR
Event 6B1 Relative Threshold for
UEDCHTTIRECFG AmrThd6B1 AMR
UEDCHTTIRECFG WAmrEventAThd WAMR
UEDCHTTIRECFG WAmrThd6A1 WAMR
UEDCHTTIRECFG WAmrThd6B1 WAMR
UEDCHTTIRECFG VoipEventAThd VoIP
UEDCHTTIRECFG VoipThd6A1 VoIP
UEDCHTTIRECFG VoipThd6B1 VoIP
UEDCHTTIRECFG BeThd6A1 6A1 threshold for BE
UEDCHTTIRECFG BeThd6B1 6B1 threshold for BE
UEDCHTTIRECFG BeThd6A2 6A2 threshold for BE
UEDCHTTIRECFG BeThd6B2 6B2 threshold for BE

Lower rate ratio thd of TTI 2ms To
UEDCHTTIRECFG LowRatioFor2msTo10ms 10ms
Upper rate ratio thd of TTI 2ms To
UEDCHTTIRECFG UpRatioFor2msTo10msBaseRtwp 10ms for RTWP/Cover
Upper rate ratio thd of TTI 2ms To
UEDCHTTIRECFG UpRatioFor2msTo10msBaseCE 10ms for CE
UEDCHTTIRECFG RatioFor10msTo2ms Rate ratio thd of TTI 10ms To 2ms
UEDCHTTIRECFG ResourceOption Resource Option
UERACHACTOASCMAP CellId Cell ID
UERACHACTOASCMAP Ac09ToAsc AC 0~9 to ASC mapping
UERACHACTOASCMAP Ac10ToAsc AC 10 to ASC mapping
UERACHASC CellId Cell ID

ERACH Available Signature Start
UERACHASC ERACHASCAvailSigStartIndex Index
ERACH Available Signature End
UERACHASC ERACHASCAvailSigEndIndex Index
UERACHASC ERACHASCAvailSubChlNum Assigned Subchannel Number
UERACHASC ERACHPersistenceFactors ERACH Persist Scaling Factor
UERACHBASIC CellId Cell ID
UERACHBASIC CommonEdchTTISelect TTI for Common E-DCH

ERACH Available Preamble
UERACHBASIC ERACHAvailPreambleSig Signatures
Available Subchannels for ERACH

UERACHBASIC ERACHAvailableSubChannel UEs
UERACHBASIC ERACHConstantValue ERACH Preamble Constant Value
UERACHBASIC ERACHPreambleRetransMax ERACH Preamble Retrans Max
UERACHBASIC ERACHPowerRampStep ERACH Power Ramp Step

ERACH Maximum preamble
UERACHBASIC ERACHMmax cycles
UERACHBASIC ERACHNB01max ERACH NB01 max
UERACHBASIC ERACHNB01min ERACH NB01 min

Number of Common EDCH
UERACHBASIC CommonEdchResourceNum Resources
UERACHBASIC ERACHMBR ERACH E-DCH MBR
UERACHBASIC ERACHGBR ERACH E-DCH GBR
UERACHBASIC MaxTBforCellEdgeUser Max TB Size for Cell Edge UEs
UEXT2GCELL GSMCellIndex GSM Cell Index
UEXT2GCELL GSMCellName GSM Cell Name
UEXT2GCELL NBscIndex Neighboring BSC Index
UEXT2GCELL LdPrdRprtSwitch Switch of Periodic Load Reporting

UEXT2GCELL MCC Mobile country code
UEXT2GCELL MNC Mobile network code
UEXT2GCELL CnOpGrpIndex CN Operator Group Index
UEXT2GCELL LAC Location Area Code
UEXT2GCELL CfgRacInd RAC Configuration Indication
UEXT2GCELL RAC Routing area code
UEXT2GCELL CID GSM cell ID
UEXT2GCELL NCC Network Color Code
UEXT2GCELL BCC BS Color Code

UEXT2GCELL BcchArfcn Inter-RAT Cell Frequency Number
Inter-RAT Cell Frequency Band

UEXT2GCELL BandInd Indicator
UEXT2GCELL RatCellType Inter-RAT cell type
UEXT2GCELL UseOfHcs Use of HCS
UEXT2GCELL HCSPrio HCS Priority Level

Quality Threshold for HCS
UEXT2GCELL Qhcs Reselection
UEXT2GCELL NcMode Network Control Mode

Inter-RAT cell support RIM
UEXT2GCELL SuppRIMFlag indicator
Inter-RAT cell support PS HO
UEXT2GCELL SuppPSHOFlag indicator
UEXT2GCELL CIO Cell Individual Offset
UEXT3GCELL NRncId Neighboring RNC ID
UEXT3GCELL CellId Cell ID of Neighboring RNC
UEXT3GCELL CellHostType Cell Host Type

UEXT3GCELL CellName Cell Name
UEXT3GCELL CnOpGrpIndex CN Operator Group Index
UEXT3GCELL PScrambCode DL Primary Scrambling Code
UEXT3GCELL BandInd Band Indicator
UEXT3GCELL UARFCNUplinkInd UL Frequency Ind
UEXT3GCELL UARFCNUplink Uplink UARFCN

UEXT3GCELL UARFCNDownlink Downlink UARFCN
UEXT3GCELL SlaveNRncId Slave RNC ID
UEXT3GCELL SlaveNCellId Slave Cell ID
UEXT3GCELL TxDiversityInd TX Diversity Indication
UEXT3GCELL LAC Location Area Code
UEXT3GCELL CfgRacInd RAC Configuration Indication
UEXT3GCELL RAC Routing area code
UEXT3GCELL QqualminInd Min Quality Level Ind

UEXT3GCELL Qqualmin Min Quality Level
UEXT3GCELL QrxlevminInd Min RX Level Ind
UEXT3GCELL Qrxlevmin Min RX level
UEXT3GCELL QrxlevminExtSup Min Rx level Extend Support
UEXT3GCELL DeltaQrxlevmin Delta Min Rx level
UEXT3GCELL MaxAllowedUlTxPowerInd Max Allowed UE UL TX Power Ind
UEXT3GCELL MaxAllowedUlTxPower Max Allowed UE UL TX Power
UEXT3GCELL UseOfHcs Use of HCS
UEXT3GCELL HCSPrio HCS Priority Level

Quality Threshold for HCS
UEXT3GCELL Qhcs Reselection
UEXT3GCELL SuppDpcmodeChgFlag Support DPC mode Change ind
UEXT3GCELL STTDSupInd STTD Support Indicator
UEXT3GCELL CP1SupInd CP1 Support Indicator
UEXT3GCELL ClosedLoopTimeAdjustMode Closed Loop Time Adjust Mode
DPCH Tx Diversity Mode for Other

UEXT3GCELL DpchDivModforOther User
UEXT3GCELL FdpchDivModforOther Other User
DPCH Tx Diversity Mode for

UEXT3GCELL DpchDivModforMIMO MIMO User
UEXT3GCELL FdpchDivModforMIMO MIMO User
Tx Diversity Mode for DC-HSDPA
UEXT3GCELL DivModforDCHSDPA User
UEXT3GCELL CellCapContainerFdd Cell Capability Container
UEXT3GCELL OverLayMobilityFlag OverLay Network Mobility Flag

HARQ Preamble Capability
UEXT3GCELL HarqPreaCap Indication
UEXT3GCELL CIO Cell oriented Cell Individual Offset
UEXT3GCELL EFachSupInd EFachSupInd
UEXT3GCELL APFlag APFlag
UEXT3GCELL VPLimitInd VPLimitInd
UFACH CellId Cell ID
UFACH PhyChId SCCPCH ID

UFACH TrChId FACH ID
UFACH RateMatchingAttr Rate Matching Attribute
UFACH ToAWS Time of Arrival Window Startpoint
UFACH ToAWE Time of Arrival Window Endpoint
UFACH MaxFachPower Max Transmit Power of FACH
UFACH MaxCmchPi Max Common Channel Priority
UFACH MinCmchPi Min Common Channel Priority
UFACH SigRbInd Bearing Signal Indication
UFACH ChCodingType Channel Code Type
UFACH CodingRate Coding Rate
UFACHBANDWIDTH TrafficClass Traffic class
UFACHBANDWIDTH UserPriority User Priority
UFACHBANDWIDTH BandWidthForFACH Bandwidth of Fach
UFACHDYNTFS CellId Cell ID
UFACHDYNTFS TrChId FACH ID
UFACHDYNTFS RLCSize RLC Size
UFACHDYNTFS TFsNumber Number of TFs
UFACHDYNTFS TbNumber1 TB Number of TF1
UFACHLOCH CellId Cell ID
UFACHLOCH TrChId FACH ID

UFDPCHPARA FdpchPO2 F-DPCH Power Offset
FDPCH Maximum Reference
UFDPCHRLPWR FdpchMaxRefPwr Power
FDPCH Minimum Reference
UFDPCHRLPWR FdpchMinRefPwr Power
UFRC DefaultConstantValue Default Constant Value
UFRC PwrCtrlAlg Power control algorithm selection

UL Closed Loop Power Control
UFRC UlTpcStepSize Step
UFRC FddTpcDlStepSize FDD DL power control step size
UFRC DpcMode DL power control mode

DL AMR-NB Code-Resource-
UFRC DlSaveCodeResourceSwitch Saving switch
DL DPCH puncturing limit in the
UFRC DlDpchPlSaveMode saving mode
UFRC DrxCycleLenCoef Paging DRX cycle coefficient
UFRC UlBeTraffInitBitrate UL BE traffic Initial bit rate
UFRC DlBeTraffInitBitrate DL BE traffic Initial bit rate

Upper limit of UL BE data rate in
UFRC UlDchBeUpperLimitforAmr AMR services
Upper limit of DL BE data rate in
UFRC DlDchBeUpperLimitforAmr AMR services
Upper limit of UL BE data rate in
UFRC UlDchBeUpperLimitforOther Non-AMR services
Upper limit of DL BE data rate in
UFRC DlDchBeUpperLimitforOther Non-AMR services
Streaming traffic transmission
UFRC UlStrTransModeOnHsupa mode on HSUPA
HSUPA TTI 10ms schedule period
UFRC Hsupa10msSchPrdForNonGrant without grant
UFRC Hsupa2msSchPrdForNonGrant without grant
UFRC Hsupa10msSchPrdForGrant with grant
UFRC Hsupa2msSchPrdForGrant with grant
UFRC HsupaInitialRate Initial rate of HSUPA BE traffic
UFRC DlBeH2DInitialRate DL Rate of HSDPA BE on DCH
UFRC ImsBearEnhancedSwitch IMS Bearer Enhancement Switch
UFRC ImsInitialAccessRate Ims initial rate
UFRC VoipHsupaTti HSUPA TTI type of VOIP traffic

Rate Threshold of Streaming
UFRC StreamHsupa2msTtiRateThs Services on 2ms TTI of HSUPA
Rate threshold of BE on 2ms TTI

UFRC BeHsupa2msTtiRateThs of HSUPA
UFRC EcN0Ths Ec/N0 threshold
UFRC EcN0EffectTime Ec/N0 effective time

Cell_DCH DL L2 enhance max
UFRC MacPduMaxSizeForDlL2Enhance PDU size
Cell_DCH UL L2 enhance max
UFRC RlcPduMaxSizeForUlL2Enhance RLC PDU size
Cell_DCH UL L2 enhance min
UFRC RlcPduMinSizeForUlL2Enhance RLC PDU size
Cell_FACH L2 enhance max PDU
UFRC MacPduMaxSizeForEFach size
Preferred MIMO or 64QAM

UFRC MIMOor64QAMSwitch Character
Delay Time for DTX_DRX to Take
UFRC DtxDrxEnablingDelay Effect
HSPA Technologies Retried by
UFRC RetryCapability UEs
Prefered DPCCH slot format for
UFRC DpcchSlotFmtForHspa HSPA
UFRC CSVoiceHsupaTti HSUPA TTI type of CS voice traffic
UFRC CSVoiceHspaUlRelDelay CS Voice Hspa Ul Relative Delay
UFRC CSVoiceHspaDlRelDelay CS Voice Hspa Dl Relative Delay

IMS signalling transmission mode
UFRC UlIMSTransModeOnHsupa on HSUPA
SRB transmission mode on
UFRC UlSRBTransModeOnHsupa HSUPA
Preferred MIMO_64QAM or
UFRC MIMO64QAMorDCHSDPASwitch DC_HSDPA Character
The total rate threshold of HSUPA
UFRC HsupaUl16QamTotalRateThs traffic for using 16QAM
UFRC PTTArpPriorityLevel PTT ARP Priority
UFRC PTTArpPreEmptCap PTT ARP Preemption Capability
UFRC PTTArpPreEmptVuln PTT ARP Preemption Vulnerability
UFRC PTTArpQueuingAllowed PTT ARP Queuing Allowed
UFRC PTTDrxCycleLenCoef DRX cycle coefficient of PTT user
UFRC PTTHsupaTti PTT HSUPA TTI type
UFRC DefaultSPIWeight Default SPI Weight

Cell_PCH L2 enhance max PDU
UFRC EPCHDLEL2MaxRlcPduSize size
ERACH Max RLC PDU Size
UFRC ERACHMaxPDUSizeforEUL2 Under UL Layer 2
ERACH Min RLC PDU Size Under
UFRC ERACHMinPDUSizeforEUL2 UL Layer 2
PTT traffic transmission mode on
UFRC UlPttTransModeOnHsupa HSUPA
DL TX Power Threshold of
UFRC SecCellTcpThd Secondary Cell
Threshold of HSDPA Users in
UFRC SecCellHUserNumThd Secondary Cell
UFRCCHLTYPEPARA CSVoiceChlType CS voice channel type
UFRCCHLTYPEPARA VoipChlType VOIP channel type
UFRCCHLTYPEPARA PTTChlType PTT channel type
UFRCCHLTYPEPARA ImsChlType IMS channel type
Type of Channel Preferably

UFRCCHLTYPEPARA SrbChlType Carrying Signaling RB
Effective Flag of Signaling RB

UFRCCHLTYPEPARA SrbChlTypeRrcEffectFlag Channel Type
UL BE traffic DCH decision

UFRCCHLTYPEPARA UlBeTraffDecThs threshold
DL BE traffic DCH decision

UFRCCHLTYPEPARA DlBeTraffDecThs threshold
DL streaming traffic threshold on
UFRCCHLTYPEPARA DlStrThsOnHsdpa HSDPA
UFRCCHLTYPEPARA DlBeTraffThsOnHsdpa DL BE traffic threshold on HSDPA

UL streaming traffic threshold on
UFRCCHLTYPEPARA UlStrThsOnHsupa HSUPA
UFRCCHLTYPEPARA UlBeTraffThsOnHsupa UL BE traffic threshold on HSUPA
UGIPORT SRN Subrack No.
UGIPORT SN Slot No.
UGIPORT PN Port No.

UGIPORT ISPSSHAREPORT Whether it share port with IuPS
UGIPORT VLANID VLAN ID.
UGTPU GTPUPATHTIMEOUTTHD Path Timeout Threshold
UGTPU GTPUPATHTIMEOUTMAXNUM Maximum Path Timeouts
UGTPU EchoSwitch Echo Detection Switch
UGTPU IuPsSelfCureSwitch Iu-PS Self-healing Switch
UGTPU IuPsAuditSwitch Iu-PS Audit Switch
UGTPU RsvdPara1 Reserved parameter 1
Time Window for UE Fast Speed

UHCSHO TFastSpdEst Decision
Threshold for UE Fast Speed

UHCSHO NFastSpdEst Decision
Period for UE Slow Speed
UHCSHO TCycleSlow Decision
Time Window for UE Slow Speed

UHCSHO TSlowSpdEst Decision
Threshold for UE Slow Speed

UHCSHO NSlowSpdEst Decision
Time Window For Ping-Pong

UHCSHO TRelateLength Handover Decision in Best Cell
Softer Handover Combination

UHOCOMM DivCtrlField Indication Switch
UHOCOMM HspaTimerLen HSPA Hysteresis Timer Length
Inter-Freq and Inter-RAT Coexist

UHOCOMM CoexistMeasThdChoice Measure Threshold Choice
Max Number of Cell in EDCH
UHOCOMM MaxEdchCellInActiveSet Active Set Length of Anti
The Timer
Pingpong NCOV Interfreq
UHOCOMM IFAntiPingpangTimerLength Handover
UHSDPCCH CQIPO CQI Power Offset
UHSDPCCH CQIPOforSHO CQI Power Offset Multi-RLS
UHSDPCCH CQIReF CQI Repetition Factor
UHSDPCCH CQIReFforSHO CQI Repetition Factor Multi-RLS
UHSDPCCH CQIFbCk CQI Feedback Cycle k
UHSDPCCH CQIFbCkforSHO CQI Feedback Cycle k Multi-RLS

CS Services CQI Feedback Cycle
UHSDPCCH CQIFBckforConver k
MIMO Services CQI Feedback
UHSDPCCH CQIFBckforMimo Cycle k
DC MIMO Services CQI Feedback
UHSDPCCH CQIFBckforDcMimo Cycle k
UHSSCCHLESSOPPARA TrafficClass Traffic class
UHSSCCHLESSOPPARA UseMacehs Mac-ehs Flag
UHSSCCHLESSOPPARA AlignMode Align Type
Configured TBS Count for HS-

UHSSCCHLESSOPPARA TbIndexNum SCCH Less Mode
UHSSCCHLESSOPPARA TbSizeIndex1 TB Size Index 1
UHSSCCHLESSOPPARA HspdcchSecondCodeSupp1 Support second code Flag for Tb1


UIDLEMODETIMER T300 Timer 300
UIDLEMODETIMER N300 Constant 300
UIDLEMODETIMER T312 Timer 312
UIDLEMODETIMER N312 Constant 312
UIMBCELL CellId Cell ID
UIMBCELL ClusterName Cluster Name
UIMBCELL MaxTxPower Max Transmit Power of Cell
UIMBCELL PSCHPower PSCH Transmit Power
UIMBCELL SSCHPower SSCH Transmit Power
UIMBCELL PCPICHPower PCPICH Transmit Power

UIMBCELL MaxPCPICHPower Max Transmit Power of PCPICH
UIMBCELL MinPCPICHPower Min Transmit Power of PCPICH
UIMBCELL BCHPower BCH Transmit Power
UIMBCELL MichPower MICH Power
UIMBCELL McchFachMaxPower Max FACH Power of MCCH
UIMBCLUSTER ClusterId Cluster ID
UIMBCLUSTER ClusterName Cluster Name
UIMBCLUSTER CnOpGrpIndex Cn Operator Group Index
UIMBCLUSTER TddBandInd Tdd Band Indicator
UIMBCLUSTER UARFCN TDD UARFCN
UIMBCLUSTER TCell Time Offset
UIMBCLUSTER PScrambCode DL Primary Scrambling Code
UIMBCLUSTER MPUSUBRACK MPU Subrack No.
UIMBCLUSTER MPUSLOT MPU Slot No.
UIMBCLUSTER CellReservedForOperatorUse Cell reserved for operator use

UIMBCLUSTER CellReservationExtension Cell reservation extension
UIMBCLUSTER Tbarred Access Barred Time
UIMBCLUSTERMBMSSA ClusterId Cluster ID
UIMBCLUSTERMBMSSA CnOpIndex Cn Operator Index
UIMBCLUSTERMBMSSA MbmsSaId MBMS SA ID
UIMBCLUSTERMCCH ClusterId Cluster ID
UIMBFACH ServiceBitRate Data Rate of IMB Service
UIMBFACH ServiceType Service Type
UIMBFACH FachMaxPower Maximum FACH Power
UIMBFACH PowerOffset Power Offset
UIMBNCLUSTER ClusterId Cluster ID
UIMBNCLUSTER NClusterId Neighboring Cluster ID
UIMBSERVICECH ClusterId Cluster ID
UIMBSERVICECH PhyChId Physical Channel ID

UIMBSERVICECH ServiceType Service Type
Number of IMB Services on One

UIMBSERVICECH ServiceNum Channel
UIMBSERVICECH CnOpIndex1 Index of CN Operator 1
UIMBSERVICECH ServiceId1 ID of IMB Service 1
UIMBSERVICECH ServiceBitRate1 Data Rate of IMB Service 1

Subframe Number of SCCPCH

UIMBSERVICECH SubframeNum FT2
First Channelization Code of

UIMBSERVICECH SccpchType2CodeFirst SCCPCH FT2
Last Channelization Code of

UIMBSERVICECH SccpchType2CodeLast SCCPCH FT2
UIMBSERVICECH ModuType Modulation Scheme
UIMBSERVICECH SlotFormat Timeslot Format
UIMBSWITCH IMBSwitch IMB Switch
UIMEITAC TAC_FUNC The function of the TAC
UIMEITAC TAC TAC
UIMEITAC Description Description
UIMEITAC FastDormancy Fast Dormancy Switch
UIMEITAC PROCESSSWITCH Process Control Switch
Minimum of IMSI route parameter

UIMSIIDNNSCNIDMAP ImsiRtMin in IDNNS
Maximum of IMSI route parameter

UIMSIIDNNSCNIDMAP ImsiRtMax in IDNNS
UIMSIIDNNSCNIDMAP CnOpIndex Cn Operator Index
UIMSIIDNNSCNIDMAP CNId CN node ID
UIMSISNAMAP ImsiMin The start of IMSI
UIMSISNAMAP ImsiMax The end of IMSI
UIMSISNAMAP MCC MCC
UIMSISNAMAP MNC MNC
UIMSISNAMAP SnaExistInd SNAC Configuration Indication
UIMSISNAMAP SNAC Sharing Network Area Code
UIMSISNAMAP MCC Mobile country code
UIMSISNAMAP MNC Mobile network code

UINTERFREQHOCOV InterFreqReportMode Mode

UINTERFREQHOCOV InterFreqFilterCoef Coeff
UINTERFREQHOCOV PrdReportInterval Period
UINTERFREQHOCOV HystFor2B 2B Hysteresis
UINTERFREQHOCOV HystFor2D 2D Hysteresis
UINTERFREQHOCOV HystFor2F 2F Hysteresis
UINTERFREQHOCOV HystForPrdInterFreq HHO Hysteresis
UINTERFREQHOCOV WeightForUsedFreq Weight for Used frequency

UINTERFREQHOCOV TimeToTrig2B Event 2B Trigger Delay
UINTERFREQHOCOV TimeToTrig2D Event 2D Trigger Delay
UINTERFREQHOCOV TimeToTrig2F Event 2F Trigger Delay
UINTERFREQHOCOV TimeToTrigForPrdInterFreq HHO Period Trigger Delay
Inter-freq CS Measure Start Ec/No

UINTERFREQHOCOV InterFreqCSThd2DEcN0 THD
Inter-freq CS Measure Stop Ec/No

UINTERFREQHOCOV InterFreqCSThd2FEcN0 THD

UINTERFREQHOCOV InterFreqR99PsThd2DEcN0 Ec/No THD
Inter-freq H Measure Start Ec/No

UINTERFREQHOCOV InterFreqHThd2DEcN0 THD
UINTERFREQHOCOV InterFreqR99PsThd2FEcN0 Ec/No THD
Inter-freq H Measure Stop Ec/No

UINTERFREQHOCOV InterFreqHThd2FEcN0 THD
Inter-freq CS Measure Start RSCP

UINTERFREQHOCOV InterFreqCSThd2DRSCP THD
Inter-freq CS Measure Stop RSCP

UINTERFREQHOCOV InterFreqCSThd2FRSCP THD

UINTERFREQHOCOV InterFreqR99PsThd2DRSCP RSCP THD
Inter-freq H Measure Start RSCP

UINTERFREQHOCOV InterFreqHThd2DRSCP THD
UINTERFREQHOCOV InterFreqR99PsThd2FRSCP RSCP THD
Inter-freq H Measure Stop RSCP

UINTERFREQHOCOV InterFreqHThd2FRSCP THD
Inter-freq CS Target Frequency

UINTERFREQHOCOV TargetFreqCsThdEcN0 Trigger Ec/No THD

UINTERFREQHOCOV TargetFreqR99PsThdEcN0 Frequency Trigger Ec/No THD
Inter-freq HSPA Target Frequency

UINTERFREQHOCOV TargetFreqHThdEcN0 Trigger Ec/No THD
Inter-freq CS Target Freqency

UINTERFREQHOCOV TargetFreqCsThdRscp Trigger RSCP THD

UINTERFREQHOCOV TargetFreqR99PsThdRscp Frequency Trigger RSCP THD
Inter-freq HSPA Target Freqency

UINTERFREQHOCOV TargetFreqHThdRscp Trigger RSCP THD

UINTERFREQHOCOV UsedFreqCSThdEcN0 trigger Ec/No THD

UINTERFREQHOCOV UsedFreqR99PsThdEcN0 trigger Ec/No THD

UINTERFREQHOCOV UsedFreqHThdEcN0 Ec/No THD

UINTERFREQHOCOV UsedFreqCSThdRSCP trigger RSCP THD

UINTERFREQHOCOV UsedFreqR99PsThdRSCP trigger RSCP THD

UINTERFREQHOCOV UsedFreqHThdRSCP RSCP THD
UINTERFREQHOCOV InterFreqMeasTime Inter-freq Measure Timer Length
UINTERFREQHOCOV PeriodFor2B 2B Event Retry Period
UINTERFREQHOCOV AmntOfRpt2B 2B Event Retry Max Times
Inter-freq Coverage Handover

UINTERFREQHOCOV TimeToInterfreqHO Trigger Delay

UINTERFREQHONCOV InterFreqFilterCoef Coeff
UINTERFREQHONCOV Hystfor2C 2C Hysteresis
UINTERFREQHONCOV TrigTime2C Event 2C Trigger Delay

UINTERFREQHONCOV InterFreqNCovHOThdEcN0 frequency trigger Ec/No THD
UINTERFREQHONCOV InterFreqMeasTime Inter-freq Measure Timer Length
UINTERFREQHONCOV PeriodFor2C 2C Event Retry Period
UINTERFREQHONCOV AmntOfRpt2C Event 2C Retry Max Times
UINTERFREQNCELL RNCId RNC ID

UINTERFREQNCELL CellId Cell ID
UINTERFREQNCELL NCellRncId RNC ID of a neighboring cell
UINTERFREQNCELL NCellId Neighboring Cell ID
UINTERFREQNCELL CIOOffset Neighboring Cell Oriented CIO
UINTERFREQNCELL SIB11Ind SIB11 Indicator
UINTERFREQNCELL IdleQoffset1sn IdleQoffset1sn
UINTERFREQNCELL IdleQoffset2sn IdleQoffset2sn
UINTERFREQNCELL SIB12Ind SIB12 Indicator
UINTERFREQNCELL ConnQoffset1sn ConnQoffset1sn

UINTERFREQNCELL ConnQoffset2sn ConnQoffset2sn
UINTERFREQNCELL TpenaltyHcsReselect HCS Cell Reselect Penalty Timer
UINTERFREQNCELL TempOffset1 HCS Cell Reselect TempOffset1
UINTERFREQNCELL TempOffset2 HCS Cell Reselect TempOffset2
Priority of Coverage-Based Inter-

UINTERFREQNCELL HOCovPrio Frequency Handover
UINTERFREQNCELL BlindHoFlag Blind Handover Flag
UINTERFREQNCELL BlindHOQualityCondition Blind Handover Quality Condition
UINTERFREQNCELL NPrioFlag Neighboring Cell Priority Flag
UINTERFREQNCELL NPrio Priority of Neighboring Cell
UINTERFREQNCELL DRDEcN0Threshhold Drd Ec/No Threshold
UINTERFREQNCELL MBDRFlag Flag of MBDR Cell
UINTERFREQNCELL MBDRPrio MBDR Cell Periority

UINTERFREQNCELL DrdOrLdrFlag DrdOrLdrFlag
Neighboring Cell Quality

UINTERFREQNCELL InterNCellQualReqFlag Guarantee Indication
UINTERFREQNCELL Qqualmin Min Quality Level
UINTERFREQNCELL Qrxlevmin Min RX Level
UINTERRATHOCOV InterRatReportMode Inter-RAT Report Mode
UINTERRATHOCOV FilterCoefOf2D2F 2D/2F Filter Coefficient
UINTERRATHOCOV MeasQuantityOf3A 3A Measure Quantity

UINTERRATHOCOV InterRATFilterCoef Inter-RAT Filter Coefficient
UINTERRATHOCOV WeightForUsedFreq Weight for Used Frequency

UINTERRATHOCOV InterRATPeriodReportInterval Interval
UINTERRATHOCOV Hystfor2D 2D Hysteresis
UINTERRATHOCOV Hystfor2F 2F Hysteresis
UINTERRATHOCOV Hystfor3A 3A Hysteresis
UINTERRATHOCOV HystforInterRAT Inter-RAT Hysteresis
UINTERRATHOCOV TrigTime2D 2D Event Trigger Delay Time
UINTERRATHOCOV TrigTime2F 2F Event Trigger Delay Time

UINTERRATHOCOV TrigTime3A 3A Event Trigger Delay Time

UINTERRATHOCOV TimeToTrigForNonVerify Verified GSM Cell

UINTERRATHOCOV TimeToTrigForVerify Verified GSM Cell
UINTERRATHOCOV BSICVerify BSIC Verify Switch

UINTERRATHOCOV InterRATCSThd2DEcN0 Ec/No THD
Inter-RAT CS Measure Stop Ec/No

UINTERRATHOCOV InterRATCSThd2FEcN0 THD
UINTERRATHOCOV InterRATR99PsThd2DEcN0 Ec/No THD

UINTERRATHOCOV InterRATHThd2DEcN0 Ec/No THD

UINTERRATHOCOV InterRATR99PsThd2FEcN0 Ec/No THD

UINTERRATHOCOV InterRATHThd2FEcN0 Ec/No THD

UINTERRATHOCOV InterRATCSThd2DRSCP RSCP THD
Inter-RAT CS Measure Stop

UINTERRATHOCOV InterRATCSThd2FRSCP RSCP THD
UINTERRATHOCOV InterRATR99PsThd2DRSCP RSCP THD

UINTERRATHOCOV InterRATHThd2DRSCP RSCP THD

UINTERRATHOCOV InterRATR99PsThd2FRSCP RSCP THD

UINTERRATHOCOV InterRATHThd2FRSCP RSCP THD

UINTERRATHOCOV TargetRatCsThd THD
Inter-RAT R99 PS Handover

UINTERRATHOCOV TargetRatR99PsThd Decision THD
Inter-RAT HSPA Handover
UINTERRATHOCOV TargetRatHThd Decision THD

UINTERRATHOCOV UsedFreqCsThdEcN0 Trigger Ec/No THD
UINTERRATHOCOV UsedFreqR99PsThdEcN0 Frequency Trigger Ec/No THD

UINTERRATHOCOV UsedFreqHThdEcN0 Trigger Ec/No THD
UINTERRATHOCOV UsedFreqCsThdRscp Trigger RSCP THD

UINTERRATHOCOV UsedFreqR99PsThdRscp Frequency Trigger RSCP THD
UINTERRATHOCOV UsedFreqHThdRscp Trigger RSCP THD
UINTERRATHOCOV InterRATMeasTime Inter-RAT Measure Timer Length
UINTERRATHOCOV InterRATPingPongTimer Inter-RAT Ping-Pong Timer
UINTERRATHOCOV InterRATPingPongHyst Inter-RAT Ping-Pong Hysteresis
UINTERRATHOCOV PeriodFor3A 3A Event Retry Period
UINTERRATHOCOV AmntOfRpt3A 3A Event Maximum Retry Times

UINTERRATHOCOV InterRatPhyChFailNum Failure THD

UINTERRATHOCOV PenaltyTimeForPhyChFail Failure Penalty Timer
UINTERRATHONCOV InterRATFilterCoef Inter-RAT Filter Coefficient
UINTERRATHONCOV Hystfor3C 3C Hysteresis
UINTERRATHONCOV TrigTime3C Event 3C Trigger Delay
UINTERRATHONCOV BSICVerify BSIC Verify Switch

UINTERRATHONCOV InterRATNCovHOCSThd THD
Inter-RAT PS Handover Decision
UINTERRATHONCOV InterRATNCovHOPSThd THD
Inter-RAT Handover Max Attempt

UINTERRATHONCOV InterRATHOAttempts Times
UINTERRATHONCOV InterRATMeasTime Inter-RAT Measure Timer Length
UINTERRATHONCOV SndLdInfo2GsmInd Send Load Info to GSM Ind
NCOV Reloc Ind Based on GSM

UINTERRATHONCOV NcovHoOn2GldInd Cell Load
UINTERRATHONCOV CSHOOut2GloadThd CS Domain Reloc GSM Load THD
UINTERRATHONCOV PSHOOut2GloadThd PS Domain Reloc GSM Load THD

UINTERRATHONCOV PeriodFor3C Event 3C Retry Period
UINTERRATHONCOV AmntOfRpt3C Event 3C Retry Max Times

UINTERRATHONCOV InterRatPhyChFailNum Failure THD

UINTERRATHONCOV PenaltyTimeForPhyChFail Failure Penalty Timer
Intra-frequency L3 Filter
UINTRAFREQHO FilterCoef Coefficient
Intra-frequency Measurement
UINTRAFREQHO IntraFreqMeasQuantity Quantity
UINTRAFREQHO PeriodMRReportNumfor1A Number
UINTRAFREQHO ReportIntervalfor1A Period
UINTRAFREQHO PeriodMRReportNumfor1C Number
UINTRAFREQHO ReportIntervalfor1C Period
UINTRAFREQHO PeriodMRReportNumfor1J Number
UINTRAFREQHO ReportIntervalfor1J Period
VP Service Event 1A Relative

UINTRAFREQHO IntraRelThdFor1ACSVP Threshold
CS Non-VP Service Event 1A
UINTRAFREQHO IntraRelThdFor1ACSNVP Relative THD
PS Service Event 1A Relative

UINTRAFREQHO IntraRelThdFor1APS Threshold
VP Service Event 1B Relative

UINTRAFREQHO IntraRelThdFor1BCSVP Threshold
CS Non-VP Service Event 1B

UINTRAFREQHO IntraRelThdFor1BCSNVP Relative Threshold
PS Service Event 1B Relative

UINTRAFREQHO IntraRelThdFor1BPS Threshold
Event 1F Absolute Ec/No

UINTRAFREQHO IntraAblThdFor1FEcNo Threshold
Event 1F Absolute RSCP

UINTRAFREQHO IntraAblThdFor1FRSCP Threshold
UINTRAFREQHO HystFor1A 1A Hysteresis
UINTRAFREQHO HystFor1B 1B Hysteresis
UINTRAFREQHO HystFor1C 1C Hysteresis
UINTRAFREQHO HystFor1D 1D Hysteresis
UINTRAFREQHO HystFor1F 1F Hysteresis
UINTRAFREQHO HystFor1J 1J Hysteresis
UINTRAFREQHO Weight Weighted factor

UINTRAFREQHO TrigTime1A Event 1A Triggering Delay
UINTRAFREQHO TrigTime1B Event 1B Triggering Delay
UINTRAFREQHO TrigTime1C Event 1C Triggering Delay

UINTRAFREQHO TrigTime1D Event 1D Triggering Delay
UINTRAFREQHO TrigTime1F Event 1F Triggering Delay

UINTRAFREQHO TrigTime1J Event 1J Triggering Delay
Max Evaluation Period of SHO
UINTRAFREQHO ShoFailPeriod Failure
UINTRAFREQHO ShoFailNumForDwnGrd Threshold Number of SHO Failure
UINTRAFREQHO RelThdForDwnGrd Relative Threshold of SHO Failure
Period of Penalty Timer for SHO

UINTRAFREQHO DcccShoPenaltyTime Failure After Down Rate
UINTRAFREQHO SHOQualmin Min Quality THD for SHO
UINTRAFREQHO MaxCellInActiveSet Max Number of Cell in Active Set

Event 1F Blind Handover Trigger
UINTRAFREQHO BlindHORSCP1FThreshold Condition
Intra-Frequency Measurement
UINTRAFREQHO BlindHOIntrafreqMRInterval Report Interval of Blind HO
Intra-Frequency Masurement
UINTRAFREQHO BlindHOIntrafreqMRAmount Report Amount of Blind Handover
UINTRAFREQNCELL RNCId RNC ID
UINTRAFREQNCELL CellId Cell ID
UINTRAFREQNCELL NCellRncId RNC ID of a neighboring cell
UINTRAFREQNCELL NCellId Neighboring Cell ID
UINTRAFREQNCELL CIOOffset Neighboring Cell Oriented CIO
UINTRAFREQNCELL CellsForbidden1A Affect 1A Threshold Flag
UINTRAFREQNCELL CellsForbidden1B Affect 1B Threshold Flag
UINTRAFREQNCELL SIB11Ind SIB11 Indicator
UINTRAFREQNCELL IdleQoffset1sn IdleQoffset1sn

UINTRAFREQNCELL IdleQoffset2sn IdleQoffset2sn
UINTRAFREQNCELL SIB12Ind SIB12 Indicator
UINTRAFREQNCELL ConnQoffset1sn ConnQoffset1sn
UINTRAFREQNCELL ConnQoffset2sn ConnQoffset2sn
UINTRAFREQNCELL TpenaltyHcsReselect HCS Cell Reselect Penalty Timer
UINTRAFREQNCELL TempOffset1 HCS Cell Reselect TempOffset1
UINTRAFREQNCELL TempOffset2 HCS Cell Reselect TempOffset2
UINTRAFREQNCELL NPrioFlag Neighboring Cell Priority Flag
UINTRAFREQNCELL NPrio Priority of Neighboring Cell
UINTRAFREQNCELL MbmsNCellInd MBMS Neighboring Cell Indicator
UIPDL NodeBName NodeB Name

Seed of the Pseudo-random
UIPDL Seed Sequence Generator
UIPSERVICEQOS CnOpIndex Cn Operator Index
UIPSERVICEQOS RecIndex Record Index
UIPSERVICEQOS TrafficType Traffic Type
UIPSERVICEQOS MatchType Match Type
UIPSERVICEQOS IPAddress IP Address
UIPSERVICEQOS IPMask IP Mask
UIPSERVICEQOS PortNum IP Port
UIPSERVICEQOS ProtocolType IP Protocol Type
UIPSERVICEQOS TrafficPriority Traffic Priority
UIURCOMMSCCP SRN Subrack No
UIURCOMMSCCP SN Slot No
UIURGCONN NBscIndex Neighboring BSC Index

UIURGCONN IntraMbscInd Intra-MBSC Indication
UIURGCONN SRN Subrack No
UIURGCONN SN Slot No
UIURGCONN SSN Subsystem No.
UIURGCONN Dpx DSP index
UIURGCONN PeerSRN Neighboring BSC Subrack No.
UIURGCONN PeerSN Neighboring BSC Slot No.
UIURGCONN PeerSSN Subsystem No.
UIUTIMERANDNUM CnOpIndex Cn Operator Index
UIUTIMERANDNUM CNId CN node ID

Times of resending reset message
UIUTIMERANDNUM RstRsndNum to CN
UIUTIMERANDNUM RafcTmr Trafc
UIUTIMERANDNUM RatcTmr Tratc
UIUTIMERANDNUM StateIndTmr CN protection timer
UIUTIMERANDNUM IgorTmr TigOR

UIUTIMERANDNUM IntrTmr TinTR
UKPIALMTHD KpiAlarmSwitch RNC Report KPI Alarm Switch
UKPIALMTHD KpiAlarmChkTimes the Period of KPI Alarm Check
Threshold of RRC Connection

UKPIALMTHD RrcConnEstabSuccRatioThd Setup Successful Ratio
The minimum of Rrc connection

UKPIALMTHD RrcConnEstabAttMinNum request Per CPUS.
Threshold of AMR RAB Setup

UKPIALMTHD AmrRabEstabSuccRatioThd Successful Ratio
Minimum Number of AMR RAB

UKPIALMTHD AmrRabEstabAttMinNum Establish Request
Threshold of VP RAB Setup

UKPIALMTHD VpRabEstSuccRatioThd Successful Ratio
Minimum Number of VP RAB

UKPIALMTHD VpRabEstAttMinNum Establish Request
Threshold of HSDPA RAB Setup

UKPIALMTHD HsdpaRabEstSuccRatioThd Successful Ratio
Minimum Number of HSDPA RAB

UKPIALMTHD HsdpaRabEstAttMinNum Establish Request
Threshold of HSUPA RAB Setup

UKPIALMTHD HsupaRabEstSuccRatioThd Successful Ratio
Minimum Number of HSUPA RAB

UKPIALMTHD HsupaRabEstAttMinNum Establish Request
Threshold of PS RAB Setup

UKPIALMTHD PsRabEstSuccRatioThd Successful Ratio
Minimum Number of PS RAB

UKPIALMTHD PsRabEstAttMinNum Establish Request
UKPIALMTHD AmrRabAbnormRelRatioThd Threshold of AMR Call Drop Ratio
Minimum Number of AMR Call

UKPIALMTHD AmrRabRelMinNum Release
UKPIALMTHD VpRabAbnormRelRatioThd Threshold of VP Call Drop Ratio
Minimum Number of VP Call

UKPIALMTHD VpRabRelMinNum Release
UKPIALMTHD PsRabAbnormRelRatioThd Threshold of PS Call Drop Ratio
Minimum Number of PS Call

UKPIALMTHD PsRabRelMinNum Release
UKPISELFCUREPARA KPICureCtrlSwitch CPUS KPI Self-Healing Switch

Abnormal KPI Success Rate-
UKPISELFCUREPARA SuccRatioAbnThreshold Triggered Self-Healing Threshold
ULAC CnOpIndex Cn Operator Index
ULAC LAC Location Area Code
ULAC PlmnValTagMin Min PLMN Value Tag
ULAC PlmnValTagMax Max PLMN Value Tag
ULASNAMAP LAC Location Area Code
ULASNAMAP SNAC Sharing Network Area Code

ULASNAMAP MCC Mobile country code
ULASNAMAP MNC Mobile network code
ULASNAMAP LAC Location area code
ULDCALGOPARA LdrFirstPri first priority for load reshuffling
ULDCALGOPARA LdrSecondPri second priority for load reshuffling
ULDCALGOPARA LdrThirdPri third priority for load reshuffling
ULDCALGOPARA LdrFourthPri fourth priority for load reshuffling
ULDCALGOPARA LdcSwitch load control algorithm switch

NCP Congestion Flow Control
ULDCALGOPARA NcpCongFlowCtrSwitch Switch
Intra-frequency LDB period timer
ULDCPERIOD IntraFreqLdbPeriodTimerLen length
ULDCPERIOD PucPeriodTimerLen PUC period timer length
ULDCPERIOD LdrPeriodTimerLen LDR period timer length
ULDCPERIOD OlcPeriodTimerLen OLC period timer length
ULDCPERIOD FairnessPeriodTimerLen Fairness period timer length
Period of RTWP-Based Intra-

ULDCPERIOD IntraFreqUlbPeriodTimerLen frequency LB
UL basic common measure filter

ULDM UlBasicCommMeasFilterCoeff coeff
Time unit for UL basic meas rprt
ULDM ChoiceRprtUnitForUlBasicMeas cycle
ULDM TenMsecForUlBasicMeas UL basic meas rprt cycle 10ms
ULDM MinForUlBasicMeas UL basic meas rprt cycle minu
DL basic common measure filter

ULDM DlBasicCommMeasFilterCoeff coeff
Time unit for DL basic meas rprt
ULDM ChoiceRprtUnitForDlBasicMeas cycle
ULDM TenMsecForDlBasicMeas DL basic meas rprt cycle 10ms
ULDM MinForDlBasicMeas DL basic meas rprt cycle minu

Period common measure protect
ULDM PeriodProtectTimerCoeff timer coeff
ULDM LdbAvgFilterLen LDB smoothing filter length
ULDM PucAvgFilterLen PUC smoothing filter length
ULDM UlLdrAvgFilterLen UL LDR smoothing filter length
ULDM DlLdrAvgFilterLen DL LDR smoothing filter length
ULDM UlOlcAvgFilterLen UL OLC smoothing filter length
ULDM DlOlcAvgFilterLen DL OLC smoothing filter length
ULDM UlCacAvgFilterLen UL CAC smoothing filter length
ULDM DlCacAvgFilterLen DL CAC smoothing filter length

Time unit of HSDPA need pwr
ULDM ChoiceRprtUnitForHsdpaPwrMeas meas cycle
HSDPA need pwr meas cycle
ULDM TenMsecForHsdpaPwrMeas 10ms
ULDM MinForHsdpaPwrMeas minu
ULDM HsdpaNeedPwrFilterLen HSDPA need power filter len

ChoiceRprtUnitForHsdpaRateMea Time unit of HSDPA bit rate meas
ULDM s cycle
ULDM TenMsecForHsdpaPrvidRateMeas HSDPA bit rate meas cycle 10ms
ULDM MinForHsdpaPrvidRateMeas HSDPA bit rate meas cycle minu
ULDM HsdpaPrvidBitRateFilterLen HSDPA bit rate filter len

Max number of continuous invalid
ULDM MaxMeasContInvalidTimes measurement
ULDM UlOlcMeasFilterCoeff UL overload measure filter coeff

Time unit for UL OLC meas rprt
ULDM ChoiceRprtUnitForUlOlcMeas cycle
ULDM TenMsecForUlOlcMeas UL OLC meas rprt cycle 10ms
ULDM MinForUlOlcMeas UL OLC meas rprt cycle minu
ULDM UlOlcTrigHyst UL OLC trigger hysteresis
ULDM DlOlcMeasFilterCoeff DL overload measure filter coeff

Time unit for DL OLC meas rprt
ULDM ChoiceRprtUnitForDlOlcMeas cycle
ULDM TenMsecForDlOlcMeas DL OLC meas rprt cycle 10ms
ULDM MinForDlOlcMeas DL OLC meas rprt cycle minu
ULDM DlOlcTrigHyst DL OLC trigger hysteresis

ChoiceRprtUnitForHsupaRateMea Time unit of HSUPA bit rate meas
ULDM s cycle
ULDM TenMsecForHsupaPrvidRateMeas HSUPA bit rate meas cycle 10ms
ULDM MinForHsupaPrvidRateMeas HSUPA bit rate meas cycle minu
ULDM HsupaPrvidBitRateFilterLen HSUPA bit rate filter len
ULDM UlbAvgFilterLen ULB Filter Length
ULOCELL NodeBName NodeB Name
ULOCELL LoCell Local Cell ID
ULTECELL LTECellIndex LTE Cell Index
ULTECELL LTECellName LTE Cell Name
ULTECELL EUTRANCELLID LTE Cell Identity

ULTECELL MCC Mobile Country Code
ULTECELL MNC Mobile Network Code
ULTECELL TAC Tracking Area Code
ULTECELL CnOpGrpIndex LTE Operator Group Index
ULTECELL CellPHYID LTE Physical Cell Identity
ULTECELL LTEBand LTE Cell Frequency Band
ULTECELL LTEArfcn LTE Cell Downlink Frequency
LTE Cell Supporting PS HO

ULTECELL SuppPSHOFlag Indicator
ULTECELL BlackFlag BlackCell List Flag
ULTENCELL RNCId RNC ID

ULTENCELL CellId Cell ID
ULTENCELL LTECellIndex LTE Cell Index
UMBMSALARMPARA MbmsInactTmr Set mbms data check timer
UMBMSALARMSERVICE MbmsMCC Mobile country code
UMBMSALARMSERVICE MbmsMNC Mobile network code
UMBMSALARMSERVICE MbmsServiceId MBMS ServiceId
UMBMSFACH ServiceType Service Type
UMBMSFACH ServiceBitRate Service Bit Rate
UMBMSFACH FachMaxPower Maximum FACH Power

UMBMSFACH MtchMinPerc0 Priority 0

UMBMSFACH MtchMinPerc15 Priority 15
UMBMSFACH ToAWS Time of Arrival Window Startpoint

UMBMSFACH ToAWE Time of Arrival Window Endpoint
UMBMSPERF ChIdx Channel Index
UMBMSPERF ChSwitch Channel Switch
UMBMSPERF MCC Mobile country code
UMBMSPERF MNC Mobile network code
UMBMSPERF ServiceId Service ID
UMBMSSA CnOpIndex Cn Operator Index
UMBMSSA MbmsSaId MBMS SA ID
UMBMSSCCPCH ServiceType Service Type
UMBMSSCCPCH ServiceBitRate Service Bit Rate
UMBMSSCCPCH STTDInd STTD Indicator
UMBMSSWITCH MbmsSwitch MBMS Control Switch
UMBMSSWITCH MbmsIubSharingSwitch MBMS Iub Sharing Switch

Msch Switch For NonMtchMulti
UMBMSSWITCH MschSwitchForNonMtchMulti Sccpch
UMBMSSWITCH MschSwitchForMtchMulti Msch Switch For MtchMulti Sccpch
Service Distribution and Load

UMBSCCRRM MbscServiceDiffLdbSwitch Balancing Switch
Load Difference Threshold
Between 3G And 2G Of CS
UMBSCCRRM Mbsc3G2GLdBlcCsDeltaThrd Service
PS Load Difference Threshold
Between 3G And 2G Of Ps
UMBSCCRRM Mbsc3G2GLdBlcPsDeltaThrd Service
2G Cell Load Measurement Report

UMBSCCRRM CommonMeasurementPeriod Period
Non-Coverage Handover Based
UMBSCCRRM MbscNcovHoOn2GldInd on 2G Load Indication
Load-base Handover Based on

UMBSCCRRM LoadHoOn3G2GldInd 3G2G Load Difference Indication
Adjustment Coefficient of 2G Load

UMBSCCRRM Mbsc2GLoadAdjustCoeff Value
GERAN System Information

UMBSCCRRM MbscReqGeranInfoSwitch Exchange Switch
UMBSCCRRM MbscNonLdrRedirFactor Un-LDR Redirection Factor
UMBSCCRRM MbscLdrRedirFactor LDR Redirection Factor

Service Distribute and Load
UMBSCCRRM MbscSdiffLdbPhaseSwitch Balance Phase Switch
UMCCHPERIODCOEF McchModPeriodCoef Mcch Mod Period Coefficient
UMCCHPERIODCOEF McchAccessPeriodCoef Mcch Access Period Coefficient
UMCCHPERIODCOEF McchRepPeriodCoef Mcch Repetition Period Coefficient
UMCDRD BlindDrdExceptHRetrySwitch Aperiodic DRD Retry Switch
DRD Measurement Period Retry

UMCDRD HRetryTimerLength Timer Length
Inter-Frequency Periodic
UMCDRD PrdReportInterval Measurement Report Interval
Target Frequency RSCP Trigger
UMCDRD TargetFreqThdRscp Threshold
Target Frequency EcNo Trigger

UMCDRD TargetFreqThdEcN0 Threshold
DRD Measurement Failure Punish

UMCDRD DrdFaiPenaltyPeriodNum Periods
UMCLDR InterFreqMeasTime Inter-freq Measure Timer Length
Inter-freq Measure Periodical

UMCLDR PrdReportInterval Report Period
UMCLDR TargetFreqThdRscp Trigger RSCP THD
UMCLDR TargetFreqThdEcN0 Trigger Ec/No THD
UMGWTST TstSwitch MGWTST SWITCH
UMGWTST TstImsi MGWTST USER IMSI
UMSCHFACH FachMaxPower Fach Max Power
UMTCH ServiceType Service Type

UMTCH ServiceBitRate Service Bit Rate
UMTCH MtchRohcSwitch Mtch Rohc Switch
UNATALG PROTOCOLTYPE Protocol type
UNATALG ALGSW ALG switch
UNATALG AGINGTIMER ALG Aging Time[s]
UNATRESPOOL SRN Subrack No.
UNATRESPOOL SN Slot No.
UNATRESPOOL PN Port No.
UNATRESPOOL NATINDEX NAT index
UNATRESPOOL STARTADDR Start IP address
UNATRESPOOL ENDADDR End IP address

UNATRESPOOL MAXPN MAX port No.
UNATRESPOOL MINPN MIN port No.
UNATSWITCH NATSW NAT switch
UNBMPARA ReliabilitySwitch Reliability Switch
UNBMPARA PerfEnhanceSwitch Performance Switch

UNBMPARA ReservedSwitch0 NBM Algorithm Reserved Switch 0
UNBMPARA ReservedSwitch1 NBM Algorithm Reserved Switch 1
NBM Algorithm Reserved U32
UNBMPARA ReservedU32Para0 Para 0
NBM Algorithm Reserved U32
UNBMPARA ReservedU32Para1 Para 1
NBM Algorithm Reserved U8 Para
UNBMPARA ReservedU8Para0 0
NBM Algorithm Reserved U8 Para
UNBMPARA ReservedU8Para1 1
UNBNODESYNCMONPARA NodeBName NodeB Name

UNBNODESYNCMONPARA NodeSyncTime Measurement Start Time
UNBNODESYNCMONPARA NodeSyncPeriod Measurement Period
UNBSC NBscIndex Neighboring BSC Index
UNCELLDETECTSWITCH SRN Subrack No.
UNCELLDETECTSWITCH SN Slot No.
Intra-Frequency Neighboring Cell

UNCELLDETECTSWITCH IntraFreqNCellDetectSwitch Detect Switch
Inter-Frequency Neighboring Cell

UNCELLDETECTSWITCH InterFreqNCellDetectSwitch Detect Switch
Inter-Rat Neighboring Cell Detect

UNCELLDETECTSWITCH InterRatNCellDetectSwitch Switch
UNCP NodeBName NodeB Name
UNCP CARRYLNKT Bearing Link Type
UNCP SAALLNKN SAAL link No.
UNCP SCTPLNKN SCTP link No.
UNCP MAINLINK Main Link Type
UNCP STACKMODTYPE Link Modify Type

UNCP MAINLINK Main Link Type
UNILNK SRN Subrack No.
UNILNK SN Slot No.
UNILNK UNILNKN UNI link No.
UNILNK FLOWCTRLSWITCH Flow control switch
UNILNK FCINDEX Flow control parameter index
UNILNK TRMLOADTHINDEX TRM load threshold index
UNILNK OPSEPFLAG Operator Separated Flag
UNILNK OPSEPINDEX Operator Separated Index
UNODEB NodeBName NodeB Name
UNODEB NodeBId NodeB ID
UNODEB SRN Subrack No.
UNODEB SN Slot No.
UNODEB SSN Subsystem No.
UNODEB TnlBearerType IUB Trans Bearer Type
UNODEB IPTRANSAPARTIND IP Trans Apart Ind
UNODEB TRANSDELAY IUB Trans Delay
UNODEB SATELLITEIND Satellite Trans Ind

UNODEB NodeBProtclVer NodeB Protocol Version
UNODEB RscMngMode Resource Management Mode
UNODEB NodebTraceSwitch NodeB Trace Switch
UNODEB HostType NodeB Host Type
UNODEB PeerRncId Peer RNC ID
UNODEB PeerNodebId Peer NodeB ID
UNODEB SharingType Sharing Type Of NodeB
UNODEB CnOpIndex Cn Operator Index
UNODEB DSSFlag DSS NodeB Flag
UNODEBALGOPARA NodeBName NodeB Name
UNODEBALGOPARA NodeBLdcAlgoSwitch NodeB LDC algorithm switch
UNODEBALGOPARA NodeBHsdpaMaxUserNum NodeB Max HSDPA User Number
UNODEBALGOPARA NodeBHsupaMaxUserNum NodeB Max HSUPA User Number
UNODEBALGOPARA HsupaCeConsumeSelection HSUPA Credit Consume Type

UNODEBALGOPARA RsvdPara1 Reserved parameter 1
UNODEBESN NODEBID NodeB ID
UNODEBESN NBLB1 The First Serial Number
Use the second Serial Number or

UNODEBESN USENBLB2 not
UNODEBESN NBLB2 The Second Serial Number
UNODEBESN NODEBPT NODEB Port Type
UNODEBESN PTIP NodeB Port IP Address

UNODEBESN PTIPMASK NodeB Port IP Mask
UNODEBESN NBGWIPSWITCH NodeB Gateway IP Switch
UNODEBESN NEXTHOP Forward route address
UNODEBIP NODEBID NodeB ID
UNODEBIP NBTRANTP NodeB TransType
UNODEBIP NBIPOAMIP NodeB IP_TRANS IP address
UNODEBIP NBIPOAMMASK NodeB IP_TRANS IP Mask
UNODEBIP IPSRN NodeB IP_TRANS Subrack No.

UNODEBIP IPSN NodeB IP_TRANS Slot No.
UNODEBIP IPLOGPORTFLAG Whether Binding logical port or not
UNODEBIP IPLPN Logic port No.
UNODEBIP NBATMOAMIP NodeB ATM_TRANS IP address
UNODEBIP NBATMOAMMASK NodeB ATM_TRANS IP Mask
UNODEBIP ATMSRN NodeB ATM_TRANS Subrack No.
UNODEBIP ATMSN NodeB ATM_TRANS Slot No.
UNODEBIP VLANFLAG Vlan Flag
UNODEBIP VLANID VLAN ID.
UNODEBIP VLANPRI VLAN Priority

UNODEBLDR NodeBName NodeB Name
UNODEBLDR DlLdrFirstAction DL LDR first action
UNODEBLDR DlLdrSecondAction DL LDR second action
UNODEBLDR DlLdrThirdAction DL LDR third action
UNODEBLDR DlLdrFourthAction DL LDR fourth action
UNODEBLDR DlLdrFifthAction DL LDR fifth action

UNODEBLDR DlLdrSixthAction DL LDR Sixth action
UNODEBLDR DlLdrSeventhAction DL LDR Seventh action

DL LDR-BE rate reduction RAB
UNODEBLDR DlLdrBERateReductionRabNum number
DL LDR un-ctrl RT Qos re-nego
UNODEBLDR DlLdrPsRTQosRenegRabNum RAB num
UNODEBLDR DlCSInterRatShouldBeHOUeNum DL CS should be ho user number
UNODEBLDR DlPSInterRatShouldBeHOUeNum DL PS should be ho user number

DL CS should not be ho user
UNODEBLDR DlCSInterRatShouldNotHOUeNum number
DL PS should not be ho user
UNODEBLDR DlPSInterRatShouldNotHOUeNum number
UNODEBLDR UlLdrFirstAction UL LDR first action
UNODEBLDR UlLdrSecondAction UL LDR second action

UNODEBLDR UlLdrThirdAction UL LDR third action
UNODEBLDR UlLdrFourthAction UL LDR fourth action
UNODEBLDR UlLdrFifthAction UL LDR fifth action
UNODEBLDR UlLdrSixthAction UL LDR Sixth action
UNODEBLDR UlLdrSeventhAction UL LDR Seventh action

UL LDR-BE rate reduction RAB
UNODEBLDR UlLdrBERateReductionRabNum number
UL LDR un-ctrl RT Qos re-nego
UNODEBLDR UlLdrPsRTQosRenegRabNum RAB num
UNODEBLDR UlCSInterRatShouldBeHOUeNum UL CS should be ho user number
UNODEBLDR UlPSInterRatShouldBeHOUeNum UL PS should be ho user number

UL CS should not be ho user
UNODEBLDR UlCSInterRatShouldNotHOUeNum number
UL PS should not be ho user
UNODEBLDR UlPSInterRatShouldNotHOUeNum number
UL LDR-AMR rate reduction RAB
UNODEBLDR UlLdrAMRRateReductionRabNum number
DL LDR-AMR rate reduction RAB
UNODEBLDR DlLdrAMRRateReductionRabNum number
Ul LDR Credit SF reserved
UNODEBLDR UlLdrCreditSfResThd threshold
Dl LDR Credit SF reserved
UNODEBLDR DlLdrCreditSfResThd threshold
Ul TTI HO Credit SF reserved

UNODEBLDR UlTtiCreditSfResThd threshold
UNODEBNAME NodeBId NodeB ID
UNODEBNAME NewNodeBName NodeB New Name
UNODEBOLC NodeBName NodeB Name
UNODEBOLC IubDlOlcRelRabNum DL OLC released RAB number
UNODEBOLC IubUlOlcRelRabNum UL OLC released RAB number
UNRELATION RNCId RNC ID
UNRELATION CellId Cell ID
UNRELATION NCellType Neighboring Cell Type
UNRIGLBCNIDMAP CnOpIndex Cn Operator Index
UNRIGLBCNIDMAP CNId CN node ID
UNRIGLBCNIDMAP NRI Network resource identity
UNRNC NRncId Neighboring RNC ID

UNRNC SHOTRIG SHO cross IUR trigger
UNRNC HHOTRIG HHO cross IUR trigger
UNRNC ServiceInd CN domain indication
UNRNC IurExistInd IUR Interface Existing Indication
UNRNC Dpx DSP index
UNRNC RncProtclVer RNC protocol version
UNRNC StateIndTMR Sccp state ind protection timer
UNRNC SuppIurCch IUR CCH support flag
Relocation with HHO process

UNRNC HhoRelocProcSwitch switch
UNRNC TnlBearerType IUR trans bearer type
UNRNC PsBeProcType Handover Type for PS BE Traffic
UNRNC IurHsdpaSuppInd Hsdpa cap ind over IUR for NRNC
UNRNC IurHsupaSuppInd Hsupa cap ind over IUR for NRNC

Iub Private Interface Switch of
UNRNC IubUPPrivateInterfaceSwitch User Plane
H2D procedure before reloc when
UNRNC CSVoiceOverHspaSuppInd CsOverHspa
UNRNC ProcessSwitch Process Control Switch

UNRNC RsvdPara1 Reserved parameter 1
UNRNC RsvdPara2 Reserved parameter 2

Iub Private Interface Switch of
UNRNC IubCPPrivateInterfaceSwitch Control Plane
UNRNCURA NRncId Neighboring RNC ID
UNRNCURA URAId URA ID
UNRNCURA CnOpIndex Cn Operator Index
UOFFLOAD CnOpIndex Cn Operator Index
UOFFLOAD OffloadSwitch Offload Switch
UOFFLOAD NonDTRAB Non-Direct Tunnel RAB
UOFFLOAD RegAPN Registered Access Point Name
UOFFLOAD GiPercent Gi bandwidth alloc Rate
UOFFLOAD ChargingSwitch ChargeSwitch

UOFFLOAD RsvdPara1 Reserved parameter 1
UOFFLOAD CnOpIndex Cn Operator Index
UOFFLOAD RegAPN Registered Access Point Name

UOFFLOADAPN ApnIndex Index of APN
UOFFLOADAPN CnOpIndex Cn Operator Index

UOFFLOADAPN APN Access Point Name
UOFFLOADIMEITAC TAC TAC
UOFFLOADIMEITAC Description Description
UOFFLOADIMSI CnOpIndex Cn Operator Index
UOFFLOADIMSI IMSIStart The Start of IMSI
UOFFLOADIMSI IMSIEnd The End of IMSI
UOFFLOADRAB CnOpIndex Cn Operator Index
UOFFLOADRAB UserPriority User Priority
UOFFLOADRAB OffloadService Offload Service Type
UOPERATORCFGPARA CnOpIndex Cn Operator Index
Feature Supporting Mode of CS

UOPERATORCFGPARA CsNriCfgMode Domain
Feature Supporting Mode of PS
UOPERATORCFGPARA PsNriCfgMode Domain
UOPERATORCFGPARA NNSfTmr Timer NNSF
UOPERATORCFGPARA CSNRILength Length of CS NRI in bits
UOPERATORCFGPARA PSNRILength Length of PS NRI in bits
UOPERATORCFGPARA NullNRI NullNRI VALUE

UOPERATORCFGPARA CsInfoUpdFlag CS Information Update Switch
UOPERATORCFGPARA PsInfoUpdFlag PS Information Update Switch
CS Information Update Protection

UOPERATORCFGPARA CsInfoUpdTmr Timer
PS Information Update Protection

UOPERATORCFGPARA PsInfoUpdTmr Timer
UOPERATORSHARINGMODE RANSharingSupport RAN Sharing Support
UOPERATORSHARINGMODE MOCNSupport MOCN Support
UOPERATORSHARINGMODE InterPlmnHoAllowedIntraRat Intra RAT Inter Plmn Ho Allowed

UOPERATORSHARINGMODE InterPlmnHoAllowedInterRat Inter RAT Inter Plmn Ho Allowed
UOPERATORSHARINGMODE DefaultCnOp Default CnOperator
UOPERATORSHARINGMODE MocnControlSwitch Mocn Control Switch
UOPERCAPARATERANGE CnOpIndex CN Operator Index
UOPERCAPARATERANGE DlCapacitySelect Downlink Rate Selection
UOPERCAPARATERANGE DlRateThreshold1 Downlink Rate Threshold 1

UOPERCAPARATERANGE UlCapacitySelect Uplink Rate Selection
UOPERCAPARATERANGE UlRateThreshold1 Uplink Rate Threshold 1
UOPERSCHEDULEPRIOMAP CnOpIndex CN Operator Index
UOPERSCHEDULEPRIOMAP TrafficClass Traffic Class

UOPERSCHEDULEPRIOMAP UserPriority User Priority
UOPERSCHEDULEPRIOMAP THPClass Traffic Handling Priority Class
UOPERSCHEDULEPRIOMAP SPI Scheduling Priority Indicator
UOPERSPIWEIGHT CnOpIndex CN Operator Index
UOPERSPIWEIGHT SPI Scheduling Priority Indicator
UOPERSPIWEIGHT SpiWeight SPI Weight

Configure SPI Weight Based on
UOPERSPIWEIGHT RateRangeSPIWeightInd HSPA Rate Range
SPI Weight for HSDPA Rata
UOPERSPIWEIGHT DlRateRange1SPIWeight Range 1
SPI Weight for HSUPA Rata
UOPERSPIWEIGHT UlRateRange1SPIWeight Range 1
UOPERTHPCLASS CnOpIndex CN Operator Index
User Class of Traffic Handling

UOPERTHPCLASS THP1Class Priority 1













UOPERUSERGBR CnOpIndex CN Operator Index
UOPERUSERGBR TrafficClass Traffic Class

UOPERUSERGBR THPClass Traffic Handling Priority Class
UOPERUSERGBR BearType Bearer Type
UOPERUSERGBR UserPriority User Priority
UOPERUSERGBR UlGBR Uplink GBR for BE service
UOPERUSERGBR DlGBR Downlink GBR for BE service
UOPERUSERHAPPYBR CnOpIndex CN Operator Index
UOPERUSERHAPPYBR TrafficClass Traffic class
UOPERUSERHAPPYBR UserPriority User Priority
UOPERUSERHAPPYBR THPClass Traffic Handling Priority Class

UOPERUSERHAPPYBR HappyBR Happy bit rate
UOPERUSERPRIORITY CnOpIndex CN Operator index
User_priority of
UOPERUSERPRIORITY ARP1Priority Allocation/Retention priority 1
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
Integrate Priority Configured

UOPERUSERPRIORITY PriorityReference Reference
UOPERUSERPRIORITY CarrierTypePriorInd Indicator of Carrier Type Priority
UPCCPCH CellId Cell ID
UPCCPCH PhyChId PCCPCH ID
UPCH CellId Cell ID
UPCH PhyChId SCCPCH ID
UPCH TrChId PCH ID
UPCH RateMatchingAttr Rate Matching Attribute
UPCH ToAWS Time of Arrival Window Startpoint
UPCH ToAWE Time of Arrival Window Endpoint

UPCH PCHPower PCH Power
UPCHDYNTFS CellId Cell ID
UPCHDYNTFS TrChId PCH ID
UPCHDYNTFS RLCSize RLC Size
UPCHDYNTFS TFsNumber Number of TFs
UPCHDYNTFS TbNumber1 TB Number of TF1
UPCHDYNTFS TbNumber2 TB Number of TF2
UPCPICH CellId Cell ID
UPCPICH PhyChId PCPICH ID
UPCPICH PCPICHPower PCPICH Transmit Power
UPCPICH MaxPCPICHPower Max Transmit Power of PCPICH
UPCPICH MinPCPICHPower Min Transmit Power of PCPICH
PCPICH TX Power in Small DSS

UPCPICH DSSSmallCovPCPICHPower Coverage
UPCPICHPWR CellId Cell ID
UPCPICHPWR MaxPCPICHPower Max Transmit Power of PCPICH
UPCPICHPWR MinPCPICHPower Min Transmit Power of PCPICH
UPERIODICRTTLCS PeriodicRttSwitch Periodical RTT Switch

Direct Transfer to Periodical
UPERIODICRTTLCS Direct2PeriodicSwitch Locating Switch
UPERIODICRTTLCS ReportingAmount Report Number
UPERIODICRTTLCS ReportingInterval Reporting Interval
UPICH CellId Cell ID
UPICH PhyChId SCCPCH ID
UPICH PICHId PICH ID
UPICH PICHMode PICH Mode
UPICH STTDInd STTD Indicator
UPICHPWROFFSET CellId Cell ID
UPICHPWROFFSET PICHPowerOffset PICH Power Offset
UPLMNVALTAGRANGE ModType Modification Type
UPLMNVALTAGRANGE CnOpIndex CN Operator index
UPLMNVALTAGRANGE LAC Location area code
UPLMNVALTAGRANGE RAC Routing area code
UPLMNVALTAGRANGE PlmnValTagMin Min PLMN value tag
UPLMNVALTAGRANGE PlmnValTagMax Max PLMN value tag
UPOOLPRIMHOSTPOLICY ReHostPolicy Re-host Policy Type
UPOOLPRIMHOSTPOLICY Delay Delay Time Length
UPOOLPRIMHOSTPOLICY AbsTime Specify Time
UPRACH CellId Cell ID
UPRACH PhyChId PRACH ID

UPRACH PreambleSignatures Preamble Signatures
UPRACH RACHSubChNo RACH Sub Channel No.
UPRACHACTOASCMAP CellId Cell ID
UPRACHACTOASCMAP PhyChId PRACH ID
UPRACHACTOASCMAP Ac09ToAsc AC 0~9 to ASC mapping
UPRACHACTOASCMAP Ac10ToAsc AC 10 to ASC mapping

UPRACHASC CellId Cell ID
UPRACHASC PhyChId PRACH ID
UPRACHASC AccessServiceClass Access Service Class
UPRACHASC AvailablesignatureStartIndex Available Signature Start Index
UPRACHASC AvailablesignatureEndIndex Available Signature End Index
Available Subchannel Control

UPRACHASC AvailableSubchannelCtrlWord Word
UPRACHASC PersistScalingFactor Persist Scaling Factor
UPRACHBASIC CellId Cell ID
UPRACHBASIC PhyChId PRACH ID
UPRACHBASIC PreambleSignatures Preamble Signatures
UPRACHBASIC RACHSubChNo RACH Sub Channel No.

Constant Value for Calculating
UPRACHBASIC Constantvalue Initial TX Power
UPRACHBASIC PreambleRetransMax Max Preamble Retransmission
UPRACHBASIC PowerRampStep Power Increase Step
UPRACHBASIC CTFCSize CTFC Length of TFCS
UPRACHSLOTFORMAT CellId Cell ID
UPRACHSLOTFORMAT PhyChId PRACH ID
UPRACHSLOTFORMAT SlotFormatNum Number of PRACH Slot Formats
UPRACHSLOTFORMAT SlotFormat1 Slot Format 1
UPRACHTFC CellId Cell ID
UPRACHTFC PhyChId PRACH ID

Calculated Transport Format
UPRACHTFC CTFC Combination
UPRACHTFC PowerOffsetPpm Power Offset
UPRACHTFC GainFactorBetaC Gain Factor BetaC
UPRACHTFC GainFactorBetaD Gain Factor BetaD
UPRACHUUPARAS CellId Cell ID
UPRACHUUPARAS PhyChId PRACH ID

Constant Value for Calculating
UPRACHUUPARAS Constantvalue Initial TX Power
UPRACHUUPARAS PowerRampStep Power Increase Step
UPRACHUUPARAS PreambleRetransMax Max Preamble Retransmission
UPSCH CellId Cell ID
UPSCH PhyChId PSCH ID
UPSCH PSCHPower PSCH Transmit Power
UPSINACTTIMER PsInactTmrForCon Conversational service T1
UPSINACTTIMER ProtectTmrForCon Conversational service T2
UPSINACTTIMER PsInactTmrForStr Streaming service T1
UPSINACTTIMER ProtectTmrForStr Streaming service T2
UPSINACTTIMER PsInactTmrForInt Interactive service T1
UPSINACTTIMER ProtectTmrForInt Interactive service T2
UPSINACTTIMER PsInactTmrForBac Background service T1
UPSINACTTIMER ProtectTmrForBac Background service T2
FAST DORMANCY USER T1 in

UPSINACTTIMER PsInactTmrForPreFstDrm CELL_PCH
UPSINACTTIMER ProtectTmrForImsSig IMS signal T2

UPSINACTTIMER PSInactTmrForImsSig IMS signal T1

UPSINACTTIMER PsInactTmrForFstDrmDch CELL_DCH

UPSINACTTIMER PsInactTmrForFstDrmFach CELL_FACH
Layer 1 Fast Synchronization

UPTTPARAM PTTFastL1SyncSwitch Switch
PTT Paging Message Resending
UPTTPARAM PTTPageRepeatTimes Times
PTT CELL UPDATE CONFIRM
UPTTPARAM PTTCUCRepeatTimer Message Resending Timer
PTT CELL UPDATE CONFIRM
UPTTPARAM PTTCUCRepeatTimes Message Resending Times
UPTTSTATETRANS PTTStateTransSwitch PTT State Transition Switch

PTT Direct P2D State Transition
UPTTSTATETRANS PTTP2DSwitch Switch
PTT DCH/HSPA to FACH State

UPTTSTATETRANS PTTDH2FStateTransTimer Transition Timer
PTT CPC_HSPA to FACH State

UPTTSTATETRANS PTTCpc2FStateTransTimer Transition Timer
PTT DCH/HSPA to E_FACH State

UPTTSTATETRANS PTTDH2EFachStateTransTimer Transition Timer
PTT CPC_HSPA to E_FACH State

UPTTSTATETRANS PTTCpc2EFachStateTransTimer Transition Timer
UPTTSTATETRANS PTTDH2FTvmThd PTT D/H2F 4B Threshold

UPTTSTATETRANS PTTDH2FTvmTimeToTrig PTT D/H2F 4B Time
UPTTSTATETRANS PTTDH2FTvmPTAT PTT D/H2F 4B Pending Time

UPTTSTATETRANS PTTE2FThrouMeasPeriod PTT E-DCH Throu Meas Period
UPTTSTATETRANS PTTE2FThrouThd PTT E-DCH2F 4B Threshold
UPTTSTATETRANS PTTE2FThrouTimeToTrig PTT E-DCH2F 4B Period Amount
PTT E-DCH2F 4B Pending Period

UPTTSTATETRANS PTTE2FThrouPTAT Amount
PTT FACH to PCH State

UPTTSTATETRANS PTTF2PStateTransTimer Transition Timer
UPTTSTATETRANS PTTF2PTvmThd PTT F2P 4B Threshold
UPTTSTATETRANS PTTF2PTvmTimeToTrig PTT F2P 4B Time
UPTTSTATETRANS PTTF2PTvmPTAT PTT F2P 4B Pending Time
UPTTSTATETRANS PTTF2DHTvmThd PTT F2D/HSPA 4A Threshold
UPTTSTATETRANS PTTF2DHTvmTimeToTrig PTT F2D/HSPA 4A Time

PTT Enhanced F2D/HSPA 4A
UPTTSTATETRANS PTTEF2DHTvmThd Threshold
PTT Enhanced F2D/HSPA 4A

UPTTSTATETRANS PTTEF2DHTvmTimeToTrig Time
PTT F2P/Measurement Control
UPTTSTATETRANS PTTF2PMCModSwitch Switch
UQOSACT BEQosPerform QoS Switch for BE Traffic
UQOSACT AMRQosPerform QoS Switch for AMR Traffic
UQOSACT VPQosPerform QoS Switch for VP Traffic
UQOSACT BeUlAct1 First Action for BE Uplink QoS
UQOSACT BeUlAct2 Second Action for BE Uplink QoS
UQOSACT BeUlAct3 Third Action for BE Uplink QoS
UQOSACT BeUlRateAdjTimerLen Wait Timer for BE Uplink Rate

UQOSACT BeDlAct1 First Action for BE Downlink QoS
Second Action for BE Downlink

UQOSACT BeDlAct2 QoS
UQOSACT BeDlAct3 Third Action for BE Downlink QoS
UQOSACT BeUlEvTrigInd Indicator for BE Uplink QoS Event

Srnc Parameter for BE Downlink
UQOSACT SrncBeDlRlcQosSwitch RLC QoS
DRNC Parameter for BE Downlink

UQOSACT DrncBeDlRlcQosSwitch RLC QoS
Adjustment Switch for AMR Uplink

UQOSACT UlQosAmrAdjSwitch Rate
UQOSACT AmrUlRateAdjTimerLen Wait Timer for AMR Uplink Rate
InterFreq HO For Switch for Uplink

UQOSACT UlQosAmrInterFreqHoSwitch AMR
InterRat HO Switch for Uplink

UQOSACT UlQosAmrInterRatHoSwitch AMR
Switch of WAMR Uplink Rate

UQOSACT UlQosWAmrAdjSwitch Adjustment
UQOSACT WAmrUlRateAdjTimerLen Wait Timer for WAMR Uplink
InterFreq HO Switch for Uplink

UQOSACT UlQosWAmrInterFreqHoSwitch WAMR
InterRat HO Switch for Uplink

UQOSACT UlQosWAmrInterRatHoSwitch WAMR
Switch of AMR Downlink Rate
UQOSACT DlQosAmrAdjSwitch Adjustment
InterFreq HO Switch for Downlink

UQOSACT DlQosAmrInterFreqHoSwitch AMR
InterRat HO Switch for Downlink
UQOSACT DlQosAmrInterRatHoSwitch AMR
UQOSACT DlQosWAmrAdjSwitch Switch for WAMR Downlink Rate
InterFreq HO Switch for WAMR

UQOSACT DlQosWAmrInterFreqHoSwitch Downlink
InterRat HO Switch for WAMR
UQOSACT DlQosWAmrInterRatHoSwitch Downlink
UQOSACT UlQosVpInterFreqHoSwitch InterFreq HO Switch for Uplink VP

InterFreq HO Switch for Downlink
UQOSACT DlQosVpInterFreqHoSwitch VP
UQOSACT BeUlQos6A1McSwitch Measurement of 6A1 Switch
UQOSACT BeUlQos5AMcSwitch Measurement of 5A Switch
UQOSACT BeUlQos6DMcSwitch Measurement of 6D Switch

UQOSACT BEInterIurRateUpTimer Timer for BE Inter Iur Rate
Down Link RSCP Used-Freq THD

UQOSHO DlRscpQosHyst Hyst
Down Link QoS Measure Timer

UQOSHO DLQosMcTimerLen Length
Up Link QoS Measure Timer

UQOSHO ULQosMcTimerLen Length
3A Used-Freq Measure Quantity

UQOSHO UsedFreqMeasQuantityForQos3A for QoS
UQUALITYMEAS UlAmrTrigTime6A1 AMR Trigger Time 6A1
UQUALITYMEAS UlAmrTrigTime6A2 AMR Trigger Time 6A2
UQUALITYMEAS UlAmrTrigTime6B1 AMR Trigger Time 6B1
UQUALITYMEAS UlAmrTrigTime6B2 AMR Trigger Time 6B2

UQUALITYMEAS UlAmrTrigTime6D AMR Trigger Time 6D
UQUALITYMEAS UlVpTrigTime6A1 VP Trigger Time 6A1
UQUALITYMEAS UlVpTrigTime6B1 VP Trigger Time 6B1
UQUALITYMEAS UlVpTrigTime6D VP Trigger Time 6D
UQUALITYMEAS UlBeTrigTime6A1 BE Trigger Time 6A1
UQUALITYMEAS UlBeTrigTime6B1 BE Trigger Time 6B1
UQUALITYMEAS UlBeTrigTime6A2 BE Trigger Time 6A2
UQUALITYMEAS UlBeTrigTime6B2 BE Trigger Time 6B2
UQUALITYMEAS UlBeTrigTime6D BE Trigger Time 6D
UQUALITYMEAS UlMeasFilterCoef UL Measurement Filter Coefficient
DL TCP Measurement Filter

UQUALITYMEAS DlMeasFilterCoef Coefficient
UQUALITYMEAS DlAmrTrigTimeE AMR Trigger Time of Event E

AMR Reporting Period Unit for
UQUALITYMEAS ChoiceRptUnitForAmrE Event E
UQUALITYMEAS TenMsecForAmrE AMR Event E Reporting Period
AMR Event E Reporting Period

UQUALITYMEAS MinForAmrE minute
UQUALITYMEAS DlVpTrigTimeE VP Trigger Time of Event E

VP Reporting Period Unit for Event
UQUALITYMEAS ChoiceRptUnitForVpE E
UQUALITYMEAS TenMsecForVpE VP Event E Reporting Period

VP Event E Reporting Period
UQUALITYMEAS MinForVpE minute
UQUALITYMEAS DlBeTrigTimeE BE Trigger Time of Event E

UQUALITYMEAS ChoiceRptUnitForBeE E
UQUALITYMEAS TenMsecForBeE BE Event E Reporting Period
BE Event E Reporting Period

UQUALITYMEAS MinForBeE minute
UQUALITYMEAS DlBeTrigTimeF BE Trigger Time of Event F

UQUALITYMEAS ChoiceRptUnitForBeF F
UQUALITYMEAS TenMsecForBeF BE Event F Reporting Period

BE Event F Reporting Period
UQUALITYMEAS MinForBeF minute
UQUEUEPREEMPT PreemptAlgoSwitch Preempt algorithm switch
UQUEUEPREEMPT MbmsPreemptAlgoSwitch Mbms PreemptAlgoSwitch
UQUEUEPREEMPT PreemptRefArpSwitch PreemptRefArpSwitch
UQUEUEPREEMPT QueueAlgoSwitch Queue algorithm switch
UQUEUEPREEMPT QueueLen Queue length
UQUEUEPREEMPT PollTimerLen Poll timer length
UQUEUEPREEMPT MaxQueueTimeLen Max queuing time length

Preemptvulnerability for
UQUEUEPREEMPT EmcPreeRefVulnSwitch Emergency call switch
URAC CnOpIndex Cn Operator Index
URAC LAC Location Area Code
URAC RAC Routing Area Code
URAC PlmnValTagMin Min PLMN Value Tag
URAC PlmnValTagMax Max PLMN Value Tag
URACH CellId Cell ID
URACH PhyChId PRACH ID
URACH TrChId RACH ID
URACH RateMatchingAttr Rate Matching Attribute
URACH NB01min Random Back-off Lower Limit
URACH NB01max Random Back-off Upper Limit
URACH Mmax Max Preamble Loop
URACHDYNTFS CellId Cell ID

URACHDYNTFS TrChId RACH ID
URACHDYNTFS RLCSize RLC Size
URACHDYNTFS TFsNumber Number of TFs
URACHDYNTFS TbNumber1 TB Number of TF1
URACHDYNTFS TbNumber2 TB Number of TF2
URACHMEASUREPARA EcN0MaxUpAdjStep Maximum Ec/N0 Up Step
URACHMEASUREPARA EcN0MaxDownAdjStep Maximum Ec/N0 Down Step
URACHMEASUREPARA EcN0AdjStep Ec/N0 Adjustment Step
URACHMEASUREPARA TagetRlcRetrans Target RLC Retransmission Rate

Ec/N0 Adjustment Measurement
URACHMEASUREPARA EcN0AdjTimerLen Period
URACHMEASUREPARA MaxEcN0Value Maximum Ec/N0 Value
URACHMEASUREPARA MinEcN0Value Minimum Ec/N0 Value
UREDIRECTION TrafficType Traffic Type
UREDIRECTION RedirSwitch Redirection Switch
UREDIRECTION RedirFactorOfNorm Redirection Factor Of Normal
UREDIRECTION RedirFactorOfLDR Redirection Factor Of LDR
UREDIRECTION RedirBandInd Redirection target band indicator

UREDIRECTION ReDirUARFCNUplinkInd Index
UREDIRECTION ReDirUARFCNUplink Redirection target uplink UARFCN
UREDIRECTION ReDirUARFCNDownlink UARFCN
URESERVEOVSF CellId Cell ID
URESERVEOVSF DLOVSFSF Reserved DL code OVSF
URESERVEOVSF DLCODENO Reserved DL code No
URESERVEOVSF DLCODENO Reserved DL code No
URNCALLCELLBLK DomainType Blocked Domain Type

URNCALLCELLBLK ProcessDuration Processing Duration
URNCBASIC RncId RNC ID
URNCBASIC NSAP Source ATM address
URNCCBCPUID CnOpIndex Cn Operator Index
URNCCBCPUID SRN Subrack No.
URNCCBCPUID SN Slot No.
URNCCBCPUID SSN Subsystem No.
URNCCBPARA CBSwitch CB Switch

URNCCBPARA CTCHSwitch CTCH switch of cell broadcast
URNCCBPARA CodeScheme Code Scheme
URNCCBPARA RepeatPeriod Repeat Period
URNCCBPARA RepeatNum Repeat Number
Cell Dynamic ShutDown Switch for

URNCCELLSHUTDOWNPARA DynCellShutDownSwitch RNC
Period Judge Timer Length for Cell

URNCCELLSHUTDOWNPARA DynCellOpenJudgeTimerlen Dynamic Open
Protect Timer Length for Cell

URNCCELLSHUTDOWNPARA DynCellShutdownProtectTimerlen Dynamic ShutDown
URNCMBMSPARA MbmsTransMode Mbms Transfer Mode
URNCMBMSPARA MtchMultiplexThd MTCH Multiplex Threshold
URNCMBMSPARA CombNCellPercent Combine Neighbour Cell Percent
URNCMBMSPARA XOffset X Offset
URNCMBMSPARA NCountingThd Counting Threshold

URNCMBMSPARA NPtpToPtmOffset Ptp To Ptm Offset
URNCMBMSPARA UpLimitCountingTime Up Limit Counting Time
URNCMBMSPARA RecountingPeriod Recounting Period
URNCMBMSPARA PunishTime Punish Time
URNCMBMSPARA PtmPreemptSwitch Ptm Preempt Switch
URNCMBMSPARA PtmStrmPasiSwitch Ptm Stream Passivity Switch
URNCMBMSPARA PtmNullStrmPasiSwitch Ptm Null Stream Passivity Switch
URNCMBMSPARA MbmsPtpUlBitRate Mbms Ptp UpLink Bit Rate
URNCPOOL RncPoolIndex RncPool Index
URNCPOOL RncPoolName RncPool Name
URNCPOOL BeatSendingDis HeartBeat Sending Time Interval
URNCPOOL BeatDectThred HeartBeat Lost Times Threshold

HeartBeat Recover Times
URNCPOOL BeatRecvrThred Threshold
URNCPOOL IuStatePolicyForPool Iu State Policy For RncPool
URNCPOOLMEMBER RncPoolIndex RncPool Index
URNCPOOLMEMBER NrncId Nrnc ID
UROAMMAP MCC MCC

UROAMMAP MNC MNC
UROAMMAP CnOpIndex Cn Operator Index
UROAMMAP CnOpGrpIndex Cn Operator Group Index
UROAMMAP AvailRoamCap Capability of Roaming Operator
Cause of RRC connection

URRCESTCAUSE RrcCause establishment
Channel type for RRC

URRCESTCAUSE SigChType establishment
Switch for RRC established on

URRCESTCAUSE EFachSwitch E_FACH
Index of Channel Type for RRC

URRCESTCAUSESIGCHTYPE RrcCauseSigChTypeId Connection Establishment
SRB Channel Type for Originating
URRCESTCAUSESIGCHTYPE OrigConvCallChType Conversational Call

URRCESTCAUSESIGCHTYPE OrigSteamCallChType Streaming Call

URRCESTCAUSESIGCHTYPE OrigInterCallChType Interactive Call

URRCESTCAUSESIGCHTYPE OrigBkgCallChType Background Call

URRCESTCAUSESIGCHTYPE OrigSubStrafCallChType Subscribed traffic Call
SRB Channel Type for

URRCESTCAUSESIGCHTYPE TermConvCallChType Terminating Conversational Call

URRCESTCAUSESIGCHTYPE TermStreamCallChType Terminating Streaming Call

URRCESTCAUSESIGCHTYPE TerminterCallChType Terminating Interactive Call
URRCESTCAUSESIGCHTYPE TermBkgCallChType Terminating Background Call
SRB Channel Type for Emergency

URRCESTCAUSESIGCHTYPE EmergCallChType Call
SRB Channel Type for Inter-RAT

URRCESTCAUSESIGCHTYPE InterRatCellResChType cell re-selection
SRB Channel Type for Inter-RAT

URRCESTCAUSESIGCHTYPE InterRatCellChgChType cell change order

URRCESTCAUSESIGCHTYPE RegistChType Registration
URRCESTCAUSESIGCHTYPE DetachChType SRB Channel Type for Detach

URRCESTCAUSESIGCHTYPE OrigHighPrioSigChType High Priority Signalling

URRCESTCAUSESIGCHTYPE OrigLowPrioSigChType Low Priority Signalling
SRB Channel Type for Call re-
URRCESTCAUSESIGCHTYPE CallReChType establishment

Terminating High Priority
URRCESTCAUSESIGCHTYPE TermHighPrioSigChType Signalling

URRCESTCAUSESIGCHTYPE TermLowPrioSigChType Terminating Low Priority Signalling

URRCESTCAUSESIGCHTYPE TermCauseUnknownChType Terminating cause unknown
SRB Channel Type for MBMS ptp

URRCESTCAUSESIGCHTYPE MbmsCallChType RB request
URRCESTCAUSESIGCHTYPE DefaultChType Default SRB Channel Type

URRCTRLSWITCH PROCESSSWITCH Process switch
URRCTRLSWITCH PROCESSSWITCH2 Process Control Switch 2
URRCTRLSWITCH RsvdPara1 Reserved parameter 1

URRRSVDPARA RsvdPara1 Reserved parameter 1

USAC CnOpIndex Cn Operator Index
USAC LAC Location Area Code
USAC SAC Service Area Code
USAMBMSPARA CnOpIndex Cn Operator Index
USAMBMSPARA MbmsSaId MBMS SA ID
USAMBMSPARA MbmsTransMode Mbms Transfer Mode
USAMBMSPARA NCountingThd Counting Threshold

USAMBMSPARA NPtpToPtmOffset Ptp To Ptm Offset
USAS CnOpIndex CN Operator Index
USAS SASId SAS ID
USAS Dpx DSP Index
USAS ShareSwitch SAS Share Switch
USAS SASId SAS Index
USAS Dpx DSP Index
Intra-frequency LDB period timer

USATLDCPERIOD IntraFreqLdbPeriodTimerLen length
USATLDCPERIOD PucPeriodTimerLen PUC period timer length
USATLDCPERIOD LdrPeriodTimerLen LDR period timer length
USATLDCPERIOD OlcPeriodTimerLen OLC period timer length
USATLDCPERIOD FairnessPeriodTimerLen Fairness period timer length
Period of RTWP-Based Intra-

USATLDCPERIOD IntraFreqUlbPeriodTimerLen frequency LB
UL basic common measure filter
USATLDM UlBasicCommMeasFilterCoeff coeff
Time unit for UL basic meas rprt
USATLDM ChoiceRprtUnitForUlBasicMeas cycle
USATLDM TenMsecForUlBasicMeas UL basic meas rprt cycle 10ms
USATLDM MinForUlBasicMeas UL basic meas rprt cycle minu
DL basic common measure filter

USATLDM DlBasicCommMeasFilterCoeff coeff
Time unit for DL basic meas rprt
USATLDM ChoiceRprtUnitForDlBasicMeas cycle
USATLDM TenMsecForDlBasicMeas DL basic meas rprt cycle 10ms
USATLDM MinForDlBasicMeas DL basic meas rprt cycle minu

Period common measure protect
USATLDM PeriodProtectTimerCoeff timer coeff
USATLDM LdbAvgFilterLen LDB smoothing filter length
USATLDM PucAvgFilterLen PUC smoothing filter length
USATLDM UlLdrAvgFilterLen UL LDR smoothing filter length
USATLDM DlLdrAvgFilterLen DL LDR smoothing filter length
USATLDM UlOlcAvgFilterLen UL OLC smoothing filter length
USATLDM DlOlcAvgFilterLen DL OLC smoothing filter length
USATLDM UlCacAvgFilterLen UL CAC smoothing filter length
USATLDM DlCacAvgFilterLen DL CAC smoothing filter length

Time unit of HSDPA need pwr
USATLDM ChoiceRprtUnitForHsdpaPwrMeas meas cycle
USATLDM TenMsecForHsdpaPwrMeas 10ms
USATLDM MinForHsdpaPwrMeas minu
USATLDM HsdpaNeedPwrFilterLen HSDPA need power filter len
ChoiceRprtUnitForHsdpaRateMea Time unit of HSDPA bit rate meas
USATLDM s cycle
USATLDM TenMsecForHsdpaPrvidRateMeas HSDPA bit rate meas cycle 10ms
USATLDM MinForHsdpaPrvidRateMeas HSDPA bit rate meas cycle minu
USATLDM HsdpaPrvidBitRateFilterLen HSDPA bit rate filter len

Max number of continuous invalid
USATLDM MaxMeasContInvalidTimes measurement
USATLDM UlOlcMeasFilterCoeff UL overload measure filter coeff

Time unit for UL OLC meas rprt
USATLDM ChoiceRprtUnitForUlOlcMeas cycle
USATLDM TenMsecForUlOlcMeas UL OLC meas rprt cycle 10ms
USATLDM MinForUlOlcMeas UL OLC meas rprt cycle minu
USATLDM UlOlcTrigHyst UL OLC trigger hysteresis
USATLDM DlOlcMeasFilterCoeff DL overload measure filter coeff

Time unit for DL OLC meas rprt
USATLDM ChoiceRprtUnitForDlOlcMeas cycle
USATLDM TenMsecForDlOlcMeas DL OLC meas rprt cycle 10ms
USATLDM MinForDlOlcMeas DL OLC meas rprt cycle minu
USATLDM DlOlcTrigHyst DL OLC trigger hysteresis
USATLDM UlbAvgFilterLen ULB Filter Length
USCCPCH CellId Cell ID
USCCPCH PhyChId SCCPCH ID
USCCPCH PCHPower PCH Power

USCCPCH SCCPCHOffset SCCPCH Offset
USCCPCHBASIC CellId Cell ID
USCCPCHBASIC PhyChId SCCPCH ID
USCCPCHBASIC SCCPCHOffset SCCPCH Offset
USCCPCHBASIC ScrambCode Scrambling Code
USCCPCHBASIC STTDInd STTD Indicator
USCCPCHBASIC CTFCSize CTFC Length of TFCS
USCCPCHBASIC SlotFormat Slot Format
USCCPCHBASIC TFCIpresence TFCI Existing Indicator
USCCPCHBASIC MbmsChInd Mbms Channel Indicator
USCCPCHTFC CellId Cell ID
USCCPCHTFC PhyChId SCCPCH ID

Calculated Transport Format
USCCPCHTFC CTFC Combination
USCHEDULEPRIOMAP TrafficClass Traffic Class
USCHEDULEPRIOMAP UserPriority User Priority
USCHEDULEPRIOMAP THPClass Traffic Handling Priority Class
USCHEDULEPRIOMAP SPI Scheduling Priority Indicator
USCPICH CellId Cell ID

USMLC SmlcMethod UE Positioning Method
USMLC AGPSMethodType A-GPS Method Type
USMLC AGPSAddAssDataSendFlag A-GPS Additional Data Send Flag
UE-assisted A-GPS Data Send

USMLC UeAssAgpsAssDataSwitch switch
UE-based A-GPS Data Send

USMLC UeBasAgpsAssDataSwitch Switch
USMLC MaxGpsSats Maximum Num of GPS Satellites
USMLC OTDOAMethodType OTDOA Method Type
USMLC CELLIDRTTMethodType CELLID+RTT Method Type
USMLC EmergLCSSwitch Emergency LCS Switch
Emergency LCS Inter-Rat

USMLC InterRatHOPermit Handover Permit
USMLC InterRatHOType Inter-Rat Handover Type
USMLC OptionalIESendSwitch Optional IE Send Switch

ForcedSho Switch in CELLID+RTT
USMLC ForcedSHOSwitch Method
USMLC IntraRelThdFor1A 1A Event Relative Threshold
USMLC IntraRelThdFor1B 1B Event Relative Threshold
USMLC TrigTime1A 1A Event Trigger Delay Time
USMLC TrigTime1B 1B Event Trigger Delay Time
USMLC SHOQualmin Min Quality THD for SHO
USMLC LcsWorkMode Location Working Mode
USMLC IupcRspTimerLen Timer Length for Iupc Response
USMLC ResultGeoType Location Result Shape
USMLCCELL RNCId RNC ID
USMLCCELL CellId Cell ID
USMLCCELL CellLocCfgType Cell Location Setting Type
USMLCCELL GCDF Geo-coordinate Data Format
USMLCCELL MTRLGY Metrology
USMLCCELL AntennaLatitudeDegree Cell Antenna Latitude
USMLCCELL AntennaLongitudeDegree Cell Antenna Longitude
USMLCCELL AntennaAltitudeMeter Cell Antenna Altitude
USMLCCELL MaxAntennaRange Cell Antenna Max Coverage
USMLCCELL AntennaOrientation Cell Antenna Orientation
USMLCCELL AntennaOpening Cell Antenna Opening

USMLCCELL CellAverageHeight Cell Average Altitude
USMLCCELL CellHeightStd Cell Altitude Standard Deviation
USMLCCELL CellEnvironment Cell Environment Case
USMLCCELL CellidRttActivateFlag CELLID+RTT Method Active Flag
USMLCCELL OtdoaActivateFlag OTDOA Method Active Flag
USMLCCELL AgpsActivateFlag A-GPS Method Active Flag
USMLCCELL CellCenterLatitude Cell Center Latitude
USMLCCELL CellCenterLongitude Cell Center Longitude
USMLCCELL CellCenterAltitude Cell Center Altitude

Cell Center Uncertainty Semi-
USMLCCELL UncertSemiMajor major
USMLCCELL UncertSemiMinor minor
Cell Center Orientation Of Major
USMLCCELL OrientOfMajorAxis Axis
USMLCCELL UncertAltitude Cell Center Uncertainty Altitude
USMLCCELL AntennaLatitudeDegreeSec Cell Antenna Latitude
USMLCCELL AntennaLongitudeDegreeSec Cell Antenna Longitude
USMLCCELL CellCenterLatitudeSec Cell Center Latitude
USMLCCELL CellCenterLongitudeSec Cell Center Longitude
USMLCCELL AntennaAltitudeMeterImp Cell Antenna Altitude
USMLCCELL MaxAntennaRangeImp Cell Antenna Max Coverage
USMLCCELL CellAverageHeightImp Cell Average Altitude
USMLCCELL CellHeightStdImp Cell Altitude Standard Deviation
USMLCCELL CellCenterAltitudeImp Cell Center Altitude

USMLCCELL UncertSemiMajorImp major
USMLCCELL UncertSemiMinorImp minor
USMLCCELL UncertAltitudeImp Cell Center Uncertainty Altitude
USPG SpgId Service priority group Identity
USPG PriorityServiceForR99RT Service priority of R99 RT service
Service priority of R99 NRT

USPG PriorityServiceForR99NRT service
USPG PriorityServiceForHSDPA Service priority of HSDPA service
USPG PriorityServiceForHSUPA Service priority of HSUPA service
USPG PriorityServiceForExtRab Service priority of Other service
USPIWEIGHT SPI Scheduling Priority Indicator
USPIWEIGHT SpiWeight SPI Weight

Configure SPI Weight Based on
USPIWEIGHT RateRangeSPIWeightInd HSPA Rate Range
USPIWEIGHT DlRateRange1SPIWeight Range 1
USPIWEIGHT UlRateRange1SPIWeight Range 1
USQICOUNT SqiGoodThres SQI Good Judgment Threshold
USQICOUNT SqiBadThres SQI Bad Judgment Threshold
USRNSR SRNSRExpiryTime SRNS Relocation Expiry Time
Estimated Non-Measurement
USRNSR SRNSRDelayOffset Delay Offset
USRNSR SRNSRIurReselectTimerLen SRNSR Iur Reselection Timer
Relocation Trigger Timer After

USRNSR SRNSRTrigTimer IurCCH
Duration of Triggering Static

USRNSR SrnsrSeparateDuration Relocation
SRNS Relocation-Allowed Traffic
USRNSR SrnsRabCnDomainType Type
USSCH CellId Cell ID

USSCH PhyChId SSCH ID
USSCH SSCHPower SSCH Transmit Power
USTATETIMER RrcUeRspTmr RRC UE response timer
USTATETIMER RrcIuRelCmdTmr RRC Iu release command timer
USTATETIMER RrcRelRetranTmr RRC release retransmission timer
USTATETIMER RrcPaingType1Tmr RRC paging type 1 response timer
USTATETIMER RrcInitDtTmr RRC initial DT timer

RRC RLC completion
USTATETIMER RrcRlcAckCmpTmr acknowledgement timer
USTATETIMER RbSetupRspTmr Wait RB setup response timer

UE capability enquiry response
USTATETIMER UeCapEnqRspTmr timer
Wait RB reconfiguration response
USTATETIMER RbRecfgRspTmr timer
USTATETIMER RbRelRspTmr Wait RB release response timer
USTATETIMER RlSetupRspTmr RL setup response timer
USTATETIMER RlRecfgReadyTmr RL reconfiguration timer
USTATETIMER RlRelRspTmr RL release timer
USTATETIMER RlRstrTmr RL restoration timer

DRL AAL2 establishment
USTATETIMER DrlAal2EstIndTmr indication timer
USTATETIMER DrlRecfgCmitTmr DRL reconfiguration commit timer
USTATETIMER HoCellUpdateRspTmr HO cell update response timer
USTATETIMER HoPagingRspTmr HO paging response timer

USTATETIMER HoRelocReqTmr HO relocation request timer
HO active set update response
USTATETIMER HoAsuTmr timer
HO wait timer for TrCh or RB

USTATETIMER HoWtTrchRecfgRspTmr reconfiguration response
USTATETIMER HoPhychRecfgTmr HO PhyCh reconfiguration timer
USTATETIMER RelocCmdTmr Relocation Command timer

Relocation Iu release command
USTATETIMER RelocIuRelCmdTmr timer
USTATETIMER RelocDataFwdTmr Relocation data forwarding timer
USTATETIMER RelocAnotherTmr Relocation another request timer
USTATETIMER RelocCommitTmr Relocation commit timer

Relocation mobile info
USTATETIMER RelocMobilConfTmr confirmation timer
Relocation PhyCh reconfiguration
USTATETIMER RelocPhychRecfgTmr timer
Relocation Inter-RAT HO
USTATETIMER RelocUtranHoCmpTmr completion timer
Relocation failed Iu release
USTATETIMER RelocFailIuRelCmdTmr command timer
USTATETIMER SysHoPsResumeTmr PS resume timer after SYSHO

RRC security mode completion
USTATETIMER RrcSecrtModeCmpTmr timer
USTATETIMER UeCntCheckRspTmr UE counter check response timer
USTATETIMER CmchRsrcRspTmr CMCH RSRC response timer
USTATETIMER IuCSRelNoRABTmr Iu CS Release protection timer
USTATETIMER IuPSRelNoRABTmr Iu PS Release protection timer

Wait Time In RRC Connection
USTATETIMER RrcConnRejWaitTmr Reject Message

UTHPCLASS THP1Class Priority 1












UTYPRAB RabIndex Service parameter index
UTYPRABBASIC RabIndex Service parameter index
UTYPRABBASIC TrafficClass Traffic Class
UTYPRABBASIC Ssd Signal Source Description
UTYPRABBASIC MaxBitRate Max rate
UTYPRABBASIC CNDomainId CN domain ID
UTYPRABBASIC BetaC Reference BetaC
UTYPRABBASIC BetaD Reference BetaD
UTYPRABBASIC SHInd Service Handover Indicator

2G Cell Capability Required for
UTYPRABBASIC Req2GCap Inter-RAT Handover
UTYPRABBASIC UlFpMode UL FP Mode
UTYPRABBASIC AppliedDirect RAB Applied Direction
Service-Based Handover to LTE

UTYPRABBASIC EUTRANSHIND Allowed
UTYPRABDCCCMC RabIndex Service parameter index
UTYPRABDCCCMC Direction Direction
Traffic Measurement Event 4A

UTYPRABDCCCMC Event4aThd threshold
Traffic Measurement Event 4B

UTYPRABDCCCMC Event4bThd threshold
Pending Time After Triggering of

UTYPRABDCCCMC TimetoTrigger4A Event 4A[ms]
UTYPRABDCCCMC PendingTime4A Pending time after trigger 4A

Pending Time After Triggering of
UTYPRABDCCCMC TimetoTrigger4B Event 4B[ms]
UTYPRABDCCCMC PendingTime4B Pending time after trigger 4B
Number of MRs Before Triggering

UTYPRABDCCCMC EdchTimetoTrigger4A of Event 4A on EDCH
Number of MRs Between Two

UTYPRABDCCCMC EdchPendingTime4A Events 4A on EDCH

UTYPRABDCCCMC EdchTimetoTrigger4B of Event 4B on EDCH

UTYPRABDCCCMC EdchPendingTime4B Events 4B on EDCH

UTYPRABDCCCMC DchThrouTimetoTrigger4B of Event 4B on DCH

UTYPRABDCCCMC DchThrouPendingTime4B Events 4B on DCH
UTYPRABHSPA RabIndex Service parameter index
UTYPRABHSPA TrchType Transport channel type
UTYPRABHSPA MachsT1 MAC-hs T1 timer
UTYPRABHSPA MachsWinSize MAC-hs window size

The Number of HS-DSCH MAC-D
UTYPRABHSPA HsdschMacdPduSizeNum PDU Size
UTYPRABHSPA HsdschMacdPduSize1 HS-DSCH MAC-D PDU size1

UTYPRABHSPA MachsDiscardTimeOpt MAC-hs Discard timer option
UTYPRABHSPA MachsDiscardTime MAC-hs Discard timer
UTYPRABHSPA HsupaMaxRateUpScale HSUPA service rate extend scale

The Number of E-DCH MAC-D
UTYPRABHSPA EdchMacdPduSizeNum PDU Size
UTYPRABHSPA EdchMacdPduSize1 E-DCH MAC-D PDU size1

UTYPRABHSPA HBDelaycnd Happy bit delay time
UTYPRABHSPA MacesWinSize MAC-ES window size
UTYPRABHSPA MacesT1 MAC-es T1 timer
UTYPRABHSUPAPC RabIndex Service parameter index
UTYPRABHSUPAPC SubflowIndex Traffic Subflow Index
UTYPRABHSUPAPC TrchType Transport channel type
UTYPRABHSUPAPC Ul16QamInd Ul 16QAM Used Indication
UTYPRABHSUPAPC UlL2EnhanceInd Ul enhanced L2 Used Indication

EdPower Interpolation Priority
UTYPRABHSUPAPC EdPwrInterpolationInd Used Indication
UTYPRABHSUPAPC InitSirtarget SIR init target value
UTYPRABHSUPAPC MaxSirtarget Maximum SIR target
UTYPRABHSUPAPC MinSirtarget Minimum SIR target
UTYPRABHSUPAPC EtfciTabIdx E-TFCI Table Index
UTYPRABHSUPAPC RefEtfciNum The Number of Reference E-TFCI
UTYPRABHSUPAPC RefEtfciIdx1 Reference E-TFCI Index1

UTYPRABHSUPAPC RefEtfciPO1 Reference E-TFCI Power Offset1


UTYPRABHSUPAPC ERgch2IndStpThs E-RGCH 2-Index-Step Threshold
UTYPRABHSUPAPC ERgch3IndStpThs E-RGCH 3-Index-Step Threshold
UTYPRABHSUPAPC UlEcBoostingInd UL E-DPCCH Boosting Indication
Minimum Reduced E-DPDCH

UTYPRABHSUPAPC BetaEdMin Gain Factor
HARQ PO for Large

UTYPRABHSUPAPC HarqPOLargeRetr Retransmission
HARQ PO for Small Retrans at

UTYPRABHSUPAPC HarqPOLitRetrLRate Low Speed

UTYPRABHSUPAPC HarqPOLitRetrHRate High Speed
UTYPRABOLPC RabIndex Service parameter index
UTYPRABOLPC SubflowIndex Traffic Subflow Index
UTYPRABOLPC TrchType Transport channel type
UTYPRABOLPC DelayClass Delay Class

Target value of service
UTYPRABOLPC BLERQuality DCH_BLER
Maximum E-DCH SIR decrease
UTYPRABOLPC EdchSirMaxDownStep step
Maximum Number of E-DCH PDU
UTYPRABOLPC MaxEdchRetransNum retransfer
Edch Little Target Number of E-
UTYPRABOLPC EdchTargetLittleRetransNum DCH PDU retransfer
Edch Target Large Number of E-

UTYPRABOLPC EdchTargetLargeRetransNum DCH PDU retransfer
UTYPRABQUALITYMEAS RabIndex Service parameter index
Uplink Event 6A1 Relative

UTYPRABQUALITYMEAS UlThd6A1 Threshold
Uplink Event 6A2 Relative

UTYPRABQUALITYMEAS UlThd6A2 Threshold
Uplink Event 6B1 Relative

UTYPRABQUALITYMEAS UlThd6B1 Threshold
Uplink Event 6B2 Relative

UTYPRABQUALITYMEAS UlThd6B2 Threshold
Statistic Block Number for 5A

UTYPRABQUALITYMEAS StaBlkNum5A Event
UTYPRABQUALITYMEAS Thd5A Event 5A Threshold
UTYPRABQUALITYMEAS HangBlockNum5A Interval Block Number
UTYPRABQUALITYMEAS ThdEa Event Ea Relative Threshold
UTYPRABQUALITYMEAS ThdEb Event Eb Relative Threshold
UTYPRABRLC RabIndex Service parameter index
UTYPRABRLC SubflowIndex Traffic Subflow Index
UTYPRABRLC TrchType Transport channel type
Opposite direction transport

UTYPRABRLC OppositeTrchType channel type
UTYPRABRLC DelayClass Delay Class

UTYPRABRLC RlcMode RLC mode selection
RLC AM Mode Parameters
UTYPRABRLC AmRlcCfgPara Selection
UTYPRABRLC TxWindowSize TX window size
UTYPRABRLC TxWindowSizeLimit TX window size limit
UTYPRABRLC TimerRST Reset timer duration
UTYPRABRLC MaxRST Max resetting times
Deliver data by sequence order on

UTYPRABRLC InSequenceDeliveryOrder RNC side
UTYPRABRLC AMRlcDiscardMode AM RLC discard mode selection
UM-TM RLC discard mode

UTYPRABRLC UMTMRlcDiscardMode selection
UTYPRABRLC ExplicitTimerMRW Explicit-ind slide RX window timing
UTYPRABRLC ExplicitTimerDiscard Explicit-ind SDU discard timing

Explicit-ind MRW command max
UTYPRABRLC ExplicitMaxMRW re-TX number
UTYPRABRLC NoExplicitTimerDiscard No-explicit-ind SDU discard
UTYPRABRLC MaxDAT Discard PDU max TX

UTYPRABRLC TimerMRW Discard slide RX window timing
Discard MRW command max re-
UTYPRABRLC MaxMRW TX number
UTYPRABRLC NoDiscardMaxDAT No-Discard PDU max TX
UTYPRABRLC RxWindowSize RX window size
UTYPRABRLC RxWindowSizeLimit RX window size limit
UTYPRABRLC MissingPDUInd Missing PDU indication
UTYPRABRLC TimerStatusProhibit Status report prohibit timer

State report period transmission
UTYPRABRLC TimerStatusPeriodic timer
UTYPRABRLC CfgPollingPara Configure polling para indication
UTYPRABRLC LastTxPDUPoll Last TX PDU poll indication
UTYPRABRLC LastReTxPDUPoll Last re-TX PDU poll indication

UTYPRABRLC TimerPollProhibit Poll prohibit timer
UTYPRABRLC TimerPoll re-TX poll timer
UTYPRABRLC PollPDU PDU poll frequency
UTYPRABRLC PollSDU SDU poll frequency
UTYPRABRLC PollWindow Poll window
UTYPRABRLC TimerPollPeriodic Periodical poll interval
UTYPRABRLC UlSegInd UL RLC segment indication
UTYPRABRLC DlSegInd DL RLC segment indication

Delay Time of Retransmission
UTYPRABRLC TimeToMoniter Detection[ms]
UTYPRABRLC MoniterPrd re-TX monitor period

Filter Coefficient of RLC
UTYPRABRLC ReTransRatioFilterCoef Retransmission Ratio
UTYPRABRLC EventAThred Event A threshold

UTYPRABRLC TimeToTriggerA Hysteresis of Event A
UTYPRABRLC PendingTimeA Event A pending time after trigger
UTYPRABRLC EventBThred Event B threshold
UTYPRABRLC TimeToTriggerB Hysteresis of Event B
UTYPRABRLC PendingTimeB Event B pending time after trigger
UTYPRABRLC EventAReportDelay Event A report delay

DL L2 enhance PDU poll
UTYPRABRLC PollPDUForDlEnL2 frequency
DL L2 enhance SDU poll
UTYPRABRLC PollSDUForDlEnL2 frequency
UL L2 enhance PDU poll
UTYPRABRLC PollPDUForUlEnL2 frequency
UL L2 enhance SDU poll
UTYPRABRLC PollSDUForUlEnL2 frequency
UTYPSRBHSUPAPC SrbIndex Signalling RB index
UTYPSRBHSUPAPC TrchType Transport channel type
UTYPSRBHSUPAPC Ul16QamInd Ul 16QAM Used Indication
UTYPSRBHSUPAPC UlL2EnhanceInd Ul enhanced L2 Used Indication

EdPower Interpolation Priority
UTYPSRBHSUPAPC EdPwrInterpolationInd Used Indication
UTYPSRBHSUPAPC InitSirtarget SIR init target value
UTYPSRBHSUPAPC MaxSirtarget Maximum SIR target
UTYPSRBHSUPAPC MinSirtarget Minimum SIR target
UTYPSRBHSUPAPC EtfciTabIdx E-TFCI Table Index
UTYPSRBHSUPAPC RefEtfciNum The Number of Reference E-TFCI
UTYPSRBHSUPAPC RefEtfciIdx1 Reference E-TFCI Index1

UTYPSRBHSUPAPC RefEtfciPO1 Reference E-TFCI Power Offset1


UTYPSRBHSUPAPC ERgch2IndStpThs E-RGCH 2-Index-Step Threshold
UTYPSRBHSUPAPC ERgch3IndStpThs E-RGCH 3-Index-Step Threshold
UTYPSRBHSUPAPC UlEcBoostingInd UL E-DPCCH Boosting Indication
Minimum Reduced E-DPDCH

UTYPSRBHSUPAPC BetaEdMin Gain Factor
HARQ PO for Large

UTYPSRBHSUPAPC HarqPOLargeRetr Retransmission

UTYPSRBHSUPAPC HarqPOLitRetrLRate Low Speed

UTYPSRBHSUPAPC HarqPOLitRetrHRate High Speed
UTYPSRBRLC SrbIndex Signalling RB index
UTYPSRBRLC TrchType Transport channel type

Opposite direction transport
UTYPSRBRLC OppositeTrchType channel type
UTYPSRBRLC DelayClass Delay Class
UTYPSRBRLC LochIndex Logic channel index
UTYPSRBRLC RlcMode RLC mode selection

RLC AM mode parameters
UTYPSRBRLC AmRlcCfgPara selection
UTYPSRBRLC TxWindowSize TX window size
UTYPSRBRLC TimerRST Reset timer duration
UTYPSRBRLC AMRlcDiscardMode AM RLC discard mode selection
UM-TM RLC discard mode

UTYPSRBRLC UMTMRlcDiscardMode selection
UTYPSRBRLC ExplicitTimerMRW Explicit-ind slide RX window timing
UTYPSRBRLC ExplicitTimerDiscard Explicit-ind SDU discard timing
Explicit-ind MRW command max

UTYPSRBRLC ExplicitMaxMRW re-TX number
UTYPSRBRLC NoExplicitTimerDiscard No-explicit-ind SDU discard timer
UTYPSRBRLC MaxDAT Discard PDU max TX
UTYPSRBRLC TimerMRW Discard slide RX window timing
Discard MRW command max re-

UTYPSRBRLC MaxMRW TX number
UTYPSRBRLC NoDiscardMaxDAT No-Discard PDU max TX
UTYPSRBRLC RxWindowSize RX window size
UTYPSRBRLC MissingPDUInd Missing PDU indication
UTYPSRBRLC TimerStatusProhibit Status report prohibit timer
State report period transmission

UTYPSRBRLC TimerStatusPeriodic timer
UTYPSRBRLC CfgPollingPara Configure polling para indication
UTYPSRBRLC LastTxPDUPoll Last TX PDU poll indication
UTYPSRBRLC LastReTxPDUPoll Last re-TX PDU poll indication

UTYPSRBRLC TimerPollProhibit Poll prohibit timer
UTYPSRBRLC TimerPoll re-TX poll timer
UTYPSRBRLC PollPDU PDU poll frequency
UTYPSRBRLC PollSDU SDU poll frequency
UTYPSRBRLC PollWindow Poll window
UTYPSRBRLC TimerPollPeriodic Periodical poll interval
UTYPSRBRLC PollPDUForEnL2 L2 enhance PDU poll frequency
UTYPSRBRLC PollSDUForEnL2 L2 enhance SDU poll frequency
UU2LTEHONCOV LTEMeasTypOf3C Report Type of LTE Measurement

Layer 3 Filter Coefficient for LTE
UU2LTEHONCOV U2LTEFilterCoef Measurement
UU2LTEHONCOV U2LTEMeasTime LTE Measurement Timer Length
Measurement Quantity for Event

UU2LTEHONCOV LTEMeasQuanOf3C 3C Measurement of LTE
UU2LTEHONCOV Hystfor3C Hysteresis for Event 3C
UU2LTEHONCOV TrigTime3C Time to Trigger Event 3C
RSRP Threshold During PS

UU2LTEHONCOV TargetRatThdRSRP Handover to LTE
RSRQ Threshold During PS

UU2LTEHONCOV TargetRatThdRSRQ Handover to LTE
UUEA EncryptionAlgo Encryption algorithm

Cell Reselection Counter
UUESTATETRANS CellReSelectCounter Threshold
UUESTATETRANS D2F2PTvmThd BE D2F/R or F/R2P 4B Threshold
UUESTATETRANS D2FTvmTimeToTrig BE D2F/R 4B Time
UUESTATETRANS D2FTvmPTAT BE D2F/R 4B Pending Time
UUESTATETRANS F2PTvmTimeToTrig BE F2P 4B Time
UUESTATETRANS F2PTvmPTAT BE F2P 4B Pending Time
UUESTATETRANS BeF2DTvmThd BE F/R2D 4A Threshold
UUESTATETRANS BeF2DTvmTimeToTrig BE F/R2D 4A Time
UUESTATETRANS BeH2FTvmThd BE HS-DSCH2F 4B Threshold
UUESTATETRANS BeH2FTvmTimeToTrig BE HS-DSCH2F 4B Time
UUESTATETRANS BeH2FTvmPTAT BE HS-DSCH2F 4B Pending Time

UUESTATETRANS BeF2HTvmThd BE F2HS-DSCH 4A Threshold
UUESTATETRANS BeF2HTvmTimeToTrig BE F2HS-DSCH 4A Time
UUESTATETRANS RtDH2FTvmThd RT D/HSPA2F 4B Threshold
UUESTATETRANS RtDH2FTvmTimeToTrig RT D/HSPA2F 4B Time
UUESTATETRANS RtDH2FTvmPTAT RT D/HSPA2F 4B Pending Time
UUESTATETRANS RtF2DHTvmThd RT F2D/HSPA 4A Threshold
UUESTATETRANS RtF2DHTvmTimeToTrig RT F2D/HSPA 4A Time
UUESTATETRANS E2FThrouMeasPeriod E-DCH Throu Meas Period
UUESTATETRANS E2FThrouThd E-DCH2F 4B Threshold
UUESTATETRANS E2FThrouTimeToTrig E-DCH2F 4B Period Amount

E-DCH2F 4B Pending Period
UUESTATETRANS E2FThrouPTAT Amount
UUESTATETRANS BeF2ETvmThd BE F2E-DCH 4A Threshold
UUESTATETRANS BeF2ETvmTimeToTrig BE F2E-DCH 4A Time
BE F2CPC_HS-DSCH 4A
UUESTATETRANS BeF2CpcHTvmThd Threshold
UUESTATETRANS BeF2CpcHTvmTimeToTrig BE F2CPC_HS-DSCH 4A Time
UUESTATETRANS RtF2CpcTvmThd RT F2CPC_HSPA 4A Threshold
UUESTATETRANS RtF2CpcTvmTimeToTrig RT F2CPC_HSPA 4A Time
UUESTATETRANS BeF2CpcETvmThd BE F2CPC_E-DCH 4A Threshold
UUESTATETRANS BeF2CpcETvmTimeToTrig BE FACH2CPC_E-DCH 4A Time

UUESTATETRANS BeEFach2DTvmThd BE E_FACH2D 4A Threshold
UUESTATETRANS BeEFach2DTvmTimeToTrig BE E_FACH2D 4A Time
BE E_FACH2HS-DSCH 4A
UUESTATETRANS BeEFach2HTvmThd Threshold
UUESTATETRANS BeEFach2HTvmTimeToTrig BE E_FACH2HS-DSCH 4A Time
RT E_FACH2D/HSPA 4A
UUESTATETRANS RtEFach2DHTvmThd Threshold
UUESTATETRANS RtEFach2DHTvmTimeToTrig RT E_FACH2D/HSPA 4A Time
UUESTATETRANS BeEFach2CpcTvmThd BE E_FACH2CPC 4A Threshold
UUESTATETRANS BeEFach2CpcTvmTimeToTrig BE E_FACH2CPC 4A Time
RT E_FACH2CPC_HSPA 4A
UUESTATETRANS RtEFach2CpcTvmThd Threshold
UUESTATETRANS RtEFach2CpcTvmTimeToTrig RT E_FACH2CPC_HSPA 4A Time

Fast Dormancy User
FACH/E_FACH2DCH/HSPA 4A
UUESTATETRANS FastDormancyF2DHTvmThd Threshold
UUESTATETRANSTIMER CellReSelectTimer Cell Reselection Timer
UUESTATETRANSTIMER BeD2FStateTransTimer BE DCH to FACH Transition Timer
BE FACH or E_FACH to PCH

UUESTATETRANSTIMER BeF2PStateTransTimer Transition Timer
BE HS-DSCH to FACH Transition

UUESTATETRANSTIMER BeH2FStateTransTimer Timer
Realtime DCH or HSPA To FACH

UUESTATETRANSTIMER RtDH2FStateTransTimer Transition Timer
BE E-DCH to FACH State

UUESTATETRANSTIMER BeE2FStateTransTimer Transition Timer
UUESTATETRANSTIMER BeCpc2FStateTransTimer BE CPC to FACH Transition Timer
Realtime CPC to FACH Transition

UUESTATETRANSTIMER RtCpc2FStateTransTimer Timer
BE DCH to E_FACH Transition

UUESTATETRANSTIMER BeD2EFachStateTransTimer Timer
BE HSPA to E_FACH Transition

UUESTATETRANSTIMER BeH2EFachStateTransTimer Timer
Realtime DCH or HSPA to

UUESTATETRANSTIMER RtDH2EFachStateTransTimer E_FACH Transition Timer
BE CPC to E_FACH Transition

UUESTATETRANSTIMER BeCpc2EFachStateTransTimer Timer
Realtime CPC to E_FACH

UUESTATETRANSTIMER RtCpc2EFachStateTransTimer Transition Timer
UUIA IntegrityProtectAlgo Integrity protection algorithm

UUNOFFLOADIP CnOpIndex Cn Operator Index
UUNOFFLOADIP IpAddr IP Address
UUNOFFLOADIP Mask Mask
UURA URAId URA ID
UURA CnOpIndex Cn Operator Index
UUSERGBR TrafficClass Traffic Class
UUSERGBR THPClass Traffic Handling Priority Class
UUSERGBR BearType Bearer Type
UUSERGBR UserPriority User Priority
UUSERGBR UlGBR Uplink GBR for BE service
UUSERGBR DlGBR Downlink GBR for BE service
UUSERHAPPYBR TrafficClass Traffic class
UUSERHAPPYBR UserPriority User Priority
UUSERHAPPYBR THPClass Traffic Handling Priority Class
UUSERHAPPYBR HappyBR Happy bit rate
UUSERMBR SingalUlMBR Uplink MBR of Signal
UUSERMBR SingalDlMBR Downlink MBR of Signal
UUSERMBR StreamUlMBR Uplink MBR of Streaming
UUSERMBR StreamDlMBR Downlink MBR of Streaming
UUSERMBR ConverUlMBR Uplink MBR of Conversation
UUSERMBR ConverDlMBR Downlink MBR of Conversation

Percentage of User Plane Sharing
UUSERPLNSHAREPARA UserPlnSharingOutThd Out threshold
Percentage of User Plane Sharing

UUSERPLNSHAREPARA UserPlnSharingOutOffset Out Offset
Percentage of User Plane CPU

UUSERPLNSHAREPARA UserPlnCpuSharingOutThd Usage Sharing Out Threshold
Percentage of User Plane CPU

UUSERPLNSHAREPARA UserPlnCpuSharingOutOffset Usage Sharing Out Offset
Percentage of DSP CPU Restrain

UUSERPLNSHAREPARA DSPRestrainCpuThd Threshold
User_priority of
UUSERPRIORITY ARP1Priority Allocation/Retention priority 1
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
User_priority of
Integrate Priority Configured

UUSERPRIORITY PriorityReference Reference
UUSERPRIORITY CarrierTypePriorInd Indicator of Carrier Type Priority
UVIPIMSI VIPIMSI IMSI
UVIPTRACESW Switch Switch
UWPSALGO NbmWpsAlgorithmSwitch Set WPS Algorithm Switch
UWPSALGO NbmWpsAlgorithmPriority Set WPS user priority
VCLLOP SRN Subrack No.
VCLLOP LNKT Link type
VCLLOP SN Slot No.
VCLLOP SAALLNKN SAAL link No.
VCLLOP IPADDR IP address
VCLLOP PEERIPADDR Peer IP address

VCLLOP ANI Adjacent node ID
VCLLOP PATHID AAL2 path ID
VCLLOP LOPT Loop type
VCLLOP AUSTOP Loop time[min]
VLANID SRN Subrack No.
VLANID SN Slot No.
VLANID IPADDR Next Hop IP address.
VLANID VLANID VLAN ID.
VPCLCX LSRN Low bearing subrack No.
VPCLCX LSN Low slot No.
VPCLCX LCARRYT Low bearing type
VPCLCX LIMAGRPN Low IMA group No.
VPCLCX LUNILNKN Low UNI link No.
VPCLCX LFRAATMLNKN Low FRAATM link No.
VPCLCX LPN Low NCOPT port No.
VPCLCX HSRN High subrack No.
VPCLCX HSN High slot No.
VPCLCX HCARRYT High bearing type
VPCLCX HIMAGRPN High IMA group No.
VPCLCX HUNILNKN High UNI link No.
VPCLCX HFRAATMLNKN High FRAATM link No.

VPCLCX HPN High NCOPT port No.
VPCLCX CXT Cross type
VPCLCX LVPI Low VPI
VPCLCX LVCI Low VCI
VPCLCX HVPI High VPI
VPCLCX HVCI High VCI
VPCLCX TXTRFX TX traffic record index
VPCLCX RXTRFX RX traffic record index
VPCLCX VPCLCXN Cross connect index

NE MML Command
BSC690
0 SET UDPUCFGDATA(Optional)
ADD AAL2PATH(Mandatory)
BSC690 MOD AAL2PATH(Mandatory)
0 RMV AAL2PATH(Mandatory)
ADD AAL2PATH(Mandatory)
BSC690 MOD AAL2PATH(Mandatory)
0 RMV AAL2PATH(Mandatory)
BSC690 ADD AAL2PATH(Mandatory)

0 MOD AAL2PATH(Optional)

0 MOD AAL2PATH(Mandatory)










BSC690 ADD AAL2PATH(Optional)

BSC690
0 ADD AAL2RT(Mandatory)
BSC690
0 ADD AAL2RT(Mandatory)
ADD AAL2RT(Optional)
BSC690 MOD AAL2RT(Mandatory)
0 RMV AAL2RT(Mandatory)
BSC690 ADD AAL2RT(Optional)

0 MOD AAL2RT(Mandatory)
BSC690
0 SET AAL2TMR(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD ADJMAP(Mandatory)
BSC690 MOD ADJMAP(Mandatory)
0 RMV ADJMAP(Mandatory)
BSC690 ADD ADJMAP(Mandatory)

0 MOD ADJMAP(Optional)






ADD ADJNODE(Mandatory)
BSC690 MOD ADJNODE(Mandatory)
0 RMV ADJNODE(Mandatory)
BSC690 ADD ADJNODE(Mandatory)
0 MOD ADJNODE(Optional)

BSC690
0 ADD ADJNODE(Mandatory)
BSC690

BSC690
BSC690

BSC690 ADD ADJNODE(Optional)

BSC690
0 SET ALMBLKPARA(Mandatory)
BSC690
0 SET ALMBLKPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET ALMBLKSW(Optional)
BSC690
BSC690
BSC690
0 SET ALMCAPACITY(Optional)
BSC690
0 SET ALMCAPACITY(Optional)
BSC690
0 RMV ALMFLT(Mandatory)
BSC690
0 SET ALMLVL(Mandatory)
BSC690
0 SET ALMLVL(Mandatory)
BSC690
0 SET ALMML(Mandatory)
BSC690
0 SET ALMPORT(Mandatory)
BSC690
BSC690
0 SET ALMPORT(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET ALMSCRN(Mandatory)
BSC690
0 SET ALMSHLD(Mandatory)
BSC690
0 SET ALMSHLD(Mandatory)
BSC690
0 SET ASWPARA(Mandatory)
BSC690
0 SET ASWPARA(Mandatory)
BSC690
0 SET ASWPARA(Optional)
ADD
ATMLOGICPORT(Mandatory)
RMV
BSC690 MOD
0 ATMLOGICPORT(Mandatory)
ADD
RMV
BSC690 MOD
ADD
BSC690 MOD
BSC690 ADD ATMLOGICPORT(Optional)
0 MOD ATMLOGICPORT(Optional)
BSC690
0 ADD ATMLOGICPORT(Optional)
BSC690 ADD
BSC690 ADD
BSC690
BSC690
BSC690
BSC690
BSC690
0 ADD
ADD ATMLOGICPORT(Optional)
BSC690 ATMLOGICPORT(Mandatory)
0 MOD
ADD ATMLOGICPORT(Optional)
BSC690
BSC690
BSC690 ADD ATMLOGICPORT(Optional)

BSC690
BSC690
RMV
BSC690 MOD
BSC690
ADD ATMTRF(Mandatory)
BSC690 RMV ATMTRF(Mandatory)
0 MOD ATMTRF(Mandatory)
BSC690
0 ADD ATMTRF(Mandatory)
BSC690
0 ADD ATMTRF(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD ATMTRF(Optional)
0 MOD ATMTRF(Mandatory)
BSC690
0 SET BFDPROTOSW(Mandatory)
BSC690
BSC690
BSC690
0 SET BOXRPT(Mandatory)
BSC690
0 SET BOXRPT(Mandatory)
RMV BRD(Mandatory)
BSC690 MOD BRD(Mandatory)
0 ADD BRD(Mandatory)
RMV BRD(Mandatory)
BSC690 MOD BRD(Optional)
BSC690
0 MOD BRD(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690
0 ADD BRD(Optional)
BSC690 ADD CAB(Mandatory)
0 RMV CAB(Mandatory)
BSC690 ADD CAB(Optional)
0 MOD CAB(Optional)
BSC690
0 MOD CAB(Mandatory)
BSC690 ADD CCG(Mandatory)

0 RMV CCG(Mandatory)
BSC690 ADD CCG(Mandatory)
0 RMV CCG(Mandatory)
BSC690
0 SET CCGN(Mandatory)
BSC690
0 SET CCGN(Optional)
BSC690
0 SET CERTFILE(Optional)
BSC690
BSC690
BSC690
BSC690
0 SET CERTFILE(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 CFGDATAEFFECTIVE(Optional)
SET
BSC690 CFGDATAINEFFECTIVE(Mandato
0 ry)
BSC690 ADD CFMMA(Mandatory)
0 RMV CFMMA(Mandatory)
BSC690
0 ADD CFMMA(Mandatory)
BSC690
BSC690
BSC690
0 ADD CFMMA(Optional)
BSC690
0 ADD CFMMD(Mandatory)
BSC690 ADD CFMMD(Mandatory)
0 RMV CFMMD(Mandatory)
BSC690 ADD CFMMD(Mandatory)
BSC690
0 ADD CFMMD(Optional)
BSC690
0 ADD CFMMD(Mandatory)
BSC690
BSC690 ADD CFMMEP(Mandatory)
0 RMV CFMMEP(Mandatory)
BSC690
0 ADD CFMMEP(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET CLK(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLK(Optional)
BSC690
0 SET CLKMODE(Mandatory)
BSC690
0 SET CLKMODE(Mandatory)
BSC690 ADD CLKSRC(Mandatory)
0 RMV CLKSRC(Mandatory)
BSC690
0 ADD CLKSRC(Mandatory)
BSC690
0 SET CLKTYPE(Mandatory)
BSC690
0 SET CMCTRLSW(Mandatory)
BSC690
0 SET CONNTYPE(Mandatory)
BSC690
0 SET COPTLNK(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET COPTLNK(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UCELLMBSCCRRM(Mandatory)
MOD
UCELLMBSCCRRM(Mandatory)
BSC690 RMV
0 UCELLMBSCCRRM(Mandatory)
ADD
UCELLMBSCCRRM(Optional)
BSC690 MOD
0 UCELLMBSCCRRM(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690
0 SET CPUTHD(Mandatory)
BSC690
0 SET CPUTHD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET CTRLFACTOR(Mandatory)
BSC690
0 SET CTRLFACTOR(Mandatory)
BSC690
0 RTR DB(Mandatory)
BSC690
0 ADD DEVIP(Mandatory)
BSC690
BSC690
BSC690 ADD DEVIP(Mandatory)

0 RMV DEVIP(Mandatory)
BSC690
BSC690
0 ADD DEVIP(Optional)
BSC690 ADD DHCPRLY(Mandatory)
0 RMV DHCPRLY(Mandatory)
BSC690
0 ADD DHCPRLY(Mandatory)
BSC690
0 SET DSCPMAP(Mandatory)
BSC690
0 SET DSCPMAP(Optional)
BSC690
0 SET E1T1(Mandatory)
BSC690
BSC690
BSC690
0 SET E1T1(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET E1T1LOP(Mandatory)
BSC690
BSC690
BSC690
0 SET E1T1LOP(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 ADD EMSIP(Mandatory)
BSC690
0 ADD EMSIP(Mandatory)
BSC690
0 ADD EMSIP(Optional)
BSC690
0 ADD EMSIP(Optional)
ADD EMU(Mandatory)
BSC690 RMV EMU(Mandatory)
0 MOD EMU(Mandatory)
BSC690 ADD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
0 MOD EMU(Optional)
BSC690
0 SET ENVALMPARA(Mandatory)
BSC690
0 SET ENVALMPARA(Optional)
BSC690
BSC690
ADD ETHIP(Mandatory)
BSC690 MOD ETHIP(Mandatory)
0 RMV ETHIP(Mandatory)
BSC690 ADD ETHIP(Mandatory)
0 MOD ETHIP(Optional)
BSC690
0 ADD ETHIP(Mandatory)
BSC690
0 MOD ETHIP(Optional)
BSC690
0 SET ETHPORT(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET ETHPORT(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD ETHREDPORT(Mandatory)
0 RMV ETHREDPORT(Mandatory)
BSC690 ADD ETHTRK(Mandatory)
0 RMV ETHTRK(Mandatory)
BSC690
0
BSC690 ADD ETHTRK(Optional)
0 ADD ETHTRK(Optional)
BSC690
BSC690
0 ADD ETHTRK(Mandatory)
BSC690
BSC690
BSC690
BSC690
ADD ETHTRKIP(Mandatory)
BSC690 RMV ETHTRKIP(Mandatory)
0 MOD ETHTRKIP(Mandatory)
BSC690 ADD ETHTRKIP(Mandatory)
0 MOD ETHTRKIP(Optional)
BSC690 ADD ETHTRKIP(Mandatory)
0 MOD ETHTRKIP(Optional)
BSC690 ADD ETHTRKLNK(Mandatory)
0 RMV ETHTRKLNK(Mandatory)
BSC690
0 ADD ETHTRKLNK(Mandatory)
BSC690
BSC690
0
BSC690 ADD ETHTRKLNK(Optional)
BSC690
0 SET FACFG(Optional)
BSC690
BSC690
BSC690
0 SET FANSPEED(Mandatory)
BSC690
BSC690
BSC690
0 SET FANSPEED(Optional)
BSC690
0 SET FCCPUTHD(Mandatory)
BSC690
0 SET FCCPUTHD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET FCMSGQTHD(Mandatory)
BSC690
0 SET FCMSGQTHD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET FCSW(Mandatory)
BSC690
0 SET FCSW(Mandatory)
BSC690
0 SET FCSW(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD FRALNK(Mandatory)
BSC690 RMV FRALNK(Mandatory)
0 MOD FRALNK(Mandatory)
BSC690 ADD FRALNK(Mandatory)
0 MOD FRALNK(Optional)

BSC690
0 ADD FRALNK(Mandatory)
BSC690
0 ADD FRALNK(Mandatory)
BSC690 ADD FRALNK(Optional)

BSC690
0 SET FTPCLTPORT(Mandatory)
BSC690
0 SET FTPCLTPORT(Mandatory)
BSC690
0 MOD FTPPWD(Mandatory)
BSC690
0 MOD FTPPWD(Mandatory)
BSC690
0 SET FTPSCLT(Optional)
BSC690
0 SET FTPSCLT(Optional)
FTPSCLTDPORT(Mandatory)
MOD
BSC690 RMV
0 FTPSCLTDPORT(Mandatory)
ADD
BSC690 MOD
0 FTPSCLTDPORT(Mandatory)
BSC690
0 SET FTPSRVPORT(Mandatory)
BSC690
0 SET FTPSRVPORT(Mandatory)
BSC690
0 SET FTPSSRV(Optional)
BSC690
0 SET FTPSSRV(Mandatory)
BSC690
BSC690
BSC690 SET
0 GLOBALROUTESW(Mandatory)
ADD GPS(Mandatory)
BSC690 MOD GPS(Mandatory)
0 RMV GPS(Mandatory)
BSC690
0 ADD GPS(Mandatory)
BSC690
BSC690
BSC690
0 ADD GPS(Optional)
BSC690
0 ADD GPS(Optional)
BSC690 ADD GPS(Optional)
0 MOD GPS(Optional)
BSC690 ADD GPS(Optional)
0 MOD GPS(Optional)
BSC690 ADD GPS(Mandatory)
0 MOD GPS(Mandatory)
BSC690
0 MOD GPS(Optional)
BSC690
0 MOD GPS(Optional)
BSC690 ADD ICMPGUARD(Mandatory)
0 RMV ICMPGUARD(Mandatory)
BSC690
0 ADD ICMPGUARD(Mandatory)
ADD IMAGRP(Mandatory)
BSC690 RMV IMAGRP(Mandatory)
0 MOD IMAGRP(Mandatory)
BSC690 ADD IMAGRP(Mandatory)
BSC690 ADD IMAGRP(Optional)
0 MOD IMAGRP(Optional)





BSC690 ADD IMAGRP(Mandatory)
BSC690 RMV IMALNK(Mandatory)
0 ADD IMALNK(Mandatory)

0
BSC690 ADD IMALNK(Mandatory)
BSC690
BSC690
0 SET INFBRDRESCFG(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET IPGUARD(Mandatory)
BSC690
BSC690
BSC690
0 SET IPGUARD(Optional)
BSC690
BSC690
BSC690
ADD IPLOGICPORT(Mandatory)
BSC690 MOD IPLOGICPORT(Mandatory)
0 RMV IPLOGICPORT(Mandatory)
ADD IPLOGICPORT(Mandatory)
BSC690 MOD IPLOGICPORT(Mandatory)
BSC690 ADD IPLOGICPORT(Mandatory)
0 MOD IPLOGICPORT(Mandatory)
ADD IPLOGICPORT(Optional)
BSC690 MOD IPLOGICPORT(Optional)
BSC690
0 ADD IPLOGICPORT(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 MOD IPLOGICPORT(Optional)
BSC690 ADD IPLOGICPORT(Optional)

BSC690
0 ADD IPMUX(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690 ADD IPMUX(Optional)
0 MOD IPMUX(Optional)
BSC690 ADD IPMUX(Mandatory)
BSC690 ADD IPMUX(Mandatory)
ADD IPMUX(Optional)
BSC690 MOD IPMUX(Mandatory)
0 RMV IPMUX(Mandatory)
BSC690
0 MOD IPMUX(Mandatory)
ADD IPOAPVC(Mandatory)
BSC690 RMV IPOAPVC(Mandatory)
0 MOD IPOAPVC(Mandatory)
ADD IPOAPVC(Mandatory)
BSC690 RMV IPOAPVC(Mandatory)
BSC690 ADD IPOAPVC(Mandatory)
0 MOD IPOAPVC(Optional)
BSC690 ADD IPOAPVC(Optional)




BSC690
0 ADD IPOAPVC(Mandatory)
ADD IPPATH(Mandatory)
BSC690 MOD IPPATH(Mandatory)
0 RMV IPPATH(Mandatory)
ADD IPPATH(Mandatory)
BSC690 MOD IPPATH(Mandatory)
0 RMV IPPATH(Mandatory)
BSC690 ADD IPPATH(Mandatory)
0 MOD IPPATH(Mandatory)
BSC690
0 ADD IPPATH(Mandatory)
BSC690
0 ADD IPPATH(Optional)
BSC690
BSC690
BSC690
0 ADD IPPATH(Optional)

0 MOD IPPATH(Optional)

BSC690 ADD IPPATH(Optional)





BSC690 ADD IPPATHBIND(Mandatory)
0 RMV IPPATHBIND(Mandatory)
BSC690 ADD IPPATHBIND(Mandatory)
0 RMV IPPATHBIND(Mandatory)
BSC690
0 ADD IPPATHBIND(Mandatory)
BSC690
BSC690
ADD IPRT(Mandatory)
BSC690 RMV IPRT(Mandatory)
0 MOD IPRT(Mandatory)
ADD IPRT(Mandatory)
ADD IPRT(Mandatory)
BSC690 ADD IPRT(Mandatory)
ADD IPRT(Mandatory)
BSC690
0 ADD IPRT(Mandatory)
BSC690 ADD IPRT(Mandatory)
0 MOD IPRT(Optional)
BSC690
0 RMV IPRT(Mandatory)
ADD IPRTBIND(Mandatory)
BSC690 MOD IPRTBIND(Mandatory)
0 RMV IPRTBIND(Mandatory)
BSC690 ADD IPRTBIND(Mandatory)
0 MOD IPRTBIND(Mandatory)
BSC690
0 UPD JTGCPLD(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET LICALMTHD(Mandatory)
BSC690
0 SET LICALMTHD(Mandatory)
BSC690
0 SET LICENSE(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 RMV LICENSE(Mandatory)
0 RVK LICENSE(Optional)
BSC690
0 SET LICENSECTRL(Mandatory)
ADD LOADEQ(Mandatory)
BSC690 MOD LOADEQ(Mandatory)
0 RMV LOADEQ(Mandatory)
BSC690 ADD LOADEQ(Mandatory)
0 MOD LOADEQ(Optional)
BSC690 ADD LOADEQ(Optional)





















































BSC690
0 SET LODCTRL(Mandatory)
BSC690
0 SET LOGCFG(Mandatory)
BSC690
0 SET LOGCFG(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET LOGLIMIT(Optional)
BSC690
0 SET LOGLIMIT(Optional)
BSC690
0 SET LOGLIMIT(Mandatory)
ADD M3DE(Mandatory)
BSC690 MOD M3DE(Mandatory)
0 RMV M3DE(Mandatory)
BSC690
0 ADD M3DE(Mandatory)
BSC690
0 ADD M3DE(Mandatory)
BSC690 ADD M3DE(Mandatory)

0 MOD M3DE(Optional)
BSC690 ADD M3DE(Optional)

BSC690 ADD M3DE(Mandatory)
ADD M3LE(Mandatory)
BSC690 MOD M3LE(Mandatory)
0 RMV M3LE(Mandatory)
BSC690
0 ADD M3LE(Mandatory)
BSC690
0 ADD M3LE(Mandatory)
BSC690 ADD M3LE(Optional)

0 MOD M3LE(Optional)
BSC690 ADD M3LE(Mandatory)
0 MOD M3LE(Optional)
ADD M3LKS(Mandatory)
BSC690 MOD M3LKS(Mandatory)
0 RMV M3LKS(Mandatory)
BSC690
0 ADD M3LKS(Mandatory)
BSC690 ADD M3LKS(Optional)

0 MOD M3LKS(Optional)
BSC690
0 ADD M3LKS(Optional)
BSC690
0 ADD M3LKS(Optional)
BSC690 ADD M3LKS(Optional)
BSC690 ADD M3LKS(Mandatory)
ADD M3LNK(Mandatory)
BSC690 MOD M3LNK(Mandatory)
0 RMV M3LNK(Mandatory)
ADD M3LNK(Mandatory)
BSC690 MOD M3LNK(Mandatory)
0 RMV M3LNK(Mandatory)
BSC690
0 ADD M3LNK(Mandatory)
BSC690
0
BSC690 ADD M3LNK(Mandatory)
0 ADD M3LNK(Optional)
BSC690
0 ADD M3LNK(Mandatory)
BSC690 ADD M3LNK(Optional)
0 MOD M3LNK(Optional)
BSC690
0 ADD M3LNK(Optional)
BSC690 ADD M3LNK(Mandatory)
0 MOD M3LNK(Optional)
ADD M3RT(Mandatory)
BSC690 MOD M3RT(Mandatory)
0 RMV M3RT(Mandatory)
ADD M3RT(Mandatory)
BSC690 MOD M3RT(Mandatory)
0 RMV M3RT(Mandatory)
BSC690 ADD M3RT(Optional)

0 MOD M3RT(Optional)
BSC690 ADD M3RT(Mandatory)
0 MOD M3RT(Optional)
BSC690
0 SET MEASRSTLIMIT(Mandatory)
BSC690
BSC690
ADD MPGRP(Mandatory)
BSC690 MOD MPGRP(Mandatory)
0 RMV MPGRP(Mandatory)
BSC690 ADD MPGRP(Mandatory)
0 MOD MPGRP(Mandatory)
BSC690 ADD MPGRP(Optional)

0 MOD MPGRP(Optional)




BSC690
0 ADD MPGRP(Optional)




BSC690
BSC690
BSC690








BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD MPLNK(Mandatory)
BSC690 MOD MPLNK(Mandatory)
0 RMV MPLNK(Mandatory)
ADD MPLNK(Mandatory)
BSC690 ADD MPLNK(Mandatory)
0 MOD MPLNK(Mandatory)
BSC690
0 ADD MPLNK(Mandatory)
ADD MPLNK(Optional)
BSC690 ADD MPLNK(Optional)

0 MOD MPLNK(Optional)
BSC690 ADD MPLNK(Mandatory)


BSC690
0 SET MPUBIND(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET MSP(Mandatory)
BSC690
BSC690
BSC690
0 SET MSP(Optional)
BSC690
0 SET MSP(Optional)
BSC690
0 SET MSP(Optional)
BSC690
0 SET MSP(Optional)
BSC690
BSC690
0 SET MSP(Optional)
BSC690
0 SET MSP(Optional)
BSC690
0 SET MSPCMD(Mandatory)
BSC690
BSC690
BSC690
ADD MTP3LKS(Mandatory)
BSC690 MOD MTP3LKS(Mandatory)
0 RMV MTP3LKS(Mandatory)
BSC690
0 ADD MTP3LKS(Mandatory)
BSC690 ADD MTP3LKS(Optional)

0 MOD MTP3LKS(Optional)
BSC690 ADD MTP3LKS(Optional)
BSC690 ADD MTP3LKS(Mandatory)
ADD MTP3LNK(Mandatory)
BSC690 MOD MTP3LNK(Mandatory)
0 RMV MTP3LNK(Mandatory)
ADD MTP3LNK(Mandatory)
BSC690 MOD MTP3LNK(Mandatory)
0 RMV MTP3LNK(Mandatory)
BSC690
0 ADD MTP3LNK(Mandatory)
BSC690
BSC690
BSC690 ADD MTP3LNK(Optional)
0 MOD MTP3LNK(Optional)
BSC690 ADD MTP3LNK(Mandatory)
ADD MTP3RT(Mandatory)
BSC690 MOD MTP3RT(Mandatory)
0 RMV MTP3RT(Mandatory)
ADD MTP3RT(Mandatory)
BSC690 MOD MTP3RT(Mandatory)
0 RMV MTP3RT(Mandatory)
BSC690 ADD MTP3RT(Optional)
0 MOD MTP3RT(Optional)
BSC690 ADD MTP3RT(Mandatory)
0 MOD MTP3RT(Optional)
BSC690
0 SET MTP3TMR(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD N7DPC(Mandatory)
0 MOD N7DPC(Optional)
ADD N7DPC(Mandatory)
BSC690 MOD N7DPC(Mandatory)
0 RMV N7DPC(Mandatory)
BSC690
0 ADD N7DPC(Mandatory)
0 MOD N7DPC(Mandatory)
BSC690
0 ADD N7DPC(Mandatory)
BSC690 ADD N7DPC(Optional)



BSC690
0 ADD N7DPC(Optional)
BSC690 ADD OBJALMSHLD(Mandatory)
0 RMV OBJALMSHLD(Mandatory)
BSC690 ADD OBJALMSHLD(Optional)
0 RMV OBJALMSHLD(Optional)
BSC690
0 SET OFFICENAME(Mandatory)
BSC690 ADD OMUIPRT(Mandatory)
0 RMV OMUIPRT(Mandatory)
BSC690 ADD OMUIPRT(Mandatory)
0 RMV OMUIPRT(Mandatory)
BSC690
0 ADD OMUIPRT(Mandatory)
RMV OP(Mandatory)
BSC690 ADD OP(Mandatory)
0 MOD OP(Mandatory)
BSC690 ADD OP(Optional)
0 MOD OP(Optional)
BSC690
0 ADD OP(Mandatory)
0 MOD OP(Optional)
BSC690
0 ADD OP(Optional)

0 MOD OP(Optional)
0 MOD OP(Optional)
0 MOD OP(Mandatory)
0 MOD OP(Mandatory)
BSC690
0 ADD OP(Optional)
0 MOD OP(Mandatory)
0 MOD OP(Mandatory)
BSC690
0 ADD OP(Optional)
0 MOD OP(Mandatory)
BSC690
0 MOD OP(Optional)
BSC690
0 MOD OP(Optional)
BSC690
0 MOD OP(Optional)
BSC690
0 MOD OP(Optional)
BSC690 ADD OPC(Mandatory)
0 MOD OPC(Optional)
ADD OPC(Mandatory)
BSC690 MOD OPC(Mandatory)
0 RMV OPC(Mandatory)
BSC690
0 ADD OPC(Mandatory)
BSC690 ADD OPC(Mandatory)
0 MOD OPC(Optional)
BSC690 ADD OPC(Optional)

0 MOD OPC(Optional)
0 MOD OPC(Optional)
0 MOD OPC(Optional)

0 MOD OPC(Optional)
BSC690
0 SET OPLOCK(Mandatory)
BSC690 ADD OPSEPINFO(Mandatory)
0 RMV OPSEPINFO(Mandatory)
BSC690
0 ADD OPSEPINFO(Mandatory)
BSC690
0 ADD OPSEPINFO(Mandatory)
BSC690
0 ADD OPSEPINFO(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET OPSW(Mandatory)
BSC690
0 SET OPT(Mandatory)
BSC690
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPT(Optional)
BSC690
0 SET OPTLOP(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 RMV PATCH(Optional)
BSC690
0 RMV PATCH(Mandatory)
BSC690
BSC690
BSC690
0 SET PHBMAP(Mandatory)
BSC690
BSC690
BSC690
ADD
PORTFLOWCTRLPARA(Mandato
ry)
RMV
BSC690 PORTFLOWCTRLPARA(Mandato
0 ry)
ADD
BSC690 PORTFLOWCTRLPARA(Mandato
0 ry)
BSC690 ADD
0 PORTFLOWCTRLPARA(Optional)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
ADD PPPLNK(Mandatory)
BSC690 MOD PPPLNK(Mandatory)
0 RMV PPPLNK(Mandatory)
ADD PPPLNK(Mandatory)
BSC690 MOD PPPLNK(Mandatory)
BSC690 ADD PPPLNK(Mandatory)
0 MOD PPPLNK(Mandatory)
BSC690 ADD PPPLNK(Optional)
ADD PPPLNK(Optional)
BSC690 MOD PPPLNK(Optional)

0 MOD PPPLNK(Optional)





BSC690
0 ADD PPPLNK(Optional)

BSC690
0 ADD PPPLNK(Optional)









BSC690
BSC690
BSC690
0 SET PPPSELFLOOP(Mandatory)
BSC690
0
BSC690 SET PPPSELFLOOP(Mandatory)
BSC690
BSC690
0
0
BSC690
0 SET PWDPOLICY(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET PWRALMSW(Mandatory)
BSC690
0 SET PWRALMSW(Optional)
BSC690
0 SET PWRALMSW(Optional)
BSC690
0 SET PWRPARA(Mandatory)
BSC690
0 SET PWRPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET QUEUEMAP(Mandatory)
BSC690
BSC690
0 SET QUEUEMAP(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET QUICKCFG(Mandatory)
BSC690 RMV
0 ROLLBACKPOINT(Mandatory)
RMV
ROLLBACKPOINT(Mandatory)
BSC690 ADD
0 ROLLBACKPOINT(Mandatory)
BSC690
0 ADD ROLLBACKPOINT(Optional)
MOD
BSC690 UERACHACTOASCMAP(Mandato
0 ry)
MOD
BSC690 UERACHACTOASCMAP(Optional
0 )MOD
0 )MOD
0 )MOD
0 )
MOD
0 )MOD
0 )MOD
0 )
ADD RSCGRP(Mandatory)
BSC690 MOD RSCGRP(Mandatory)
0 RMV RSCGRP(Mandatory)
BSC690 ADD RSCGRP(Mandatory)

0 MOD RSCGRP(Optional)
BSC690
0 ADD RSCGRP(Mandatory)
BSC690
BSC690
BSC690



BSC690 ADD RSCGRP(Optional)

ADD SAALLNK(Mandatory)
BSC690 RMV SAALLNK(Mandatory)
0 MOD SAALLNK(Mandatory)
BSC690 ADD SAALLNK(Mandatory)

0 MOD SAALLNK(Optional)





BSC690 ADD SAALLNK(Optional)






BSC690
0 SET SCCPTMR(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD SCHTSK(Mandatory)
0 RMV SCHTSK(Optional)
BSC690 ADD SCHTSK(Mandatory)
0 RMV SCHTSK(Optional)
BSC690
0 SET SCHTSKSW(Optional)
BSC690
0 SET SCHTSKSW(Optional)
BSC690
0 SET SCHTSKSW(Mandatory)
BSC690
0 ADD USCPICH(Mandatory)
BSC690
0 ADD USCPICH(Optional)
BSC690
0 ADD USCPICH(Optional)
ADD SCTPLNK(Mandatory)
BSC690 MOD SCTPLNK(Mandatory)
0 RMV SCTPLNK(Mandatory)
BSC690 ADD SCTPLNK(Mandatory)

0 MOD SCTPLNK(Optional)
BSC690
0 ADD SCTPLNK(Mandatory)
BSC690 ADD SCTPLNK(Optional)


0 MOD SCTPLNK(Mandatory)









BSC690
0 ADD SCTPLNK(Optional)
BSC690
BSC690





BSC690
BSC690
BSC690
BSC690
0 SET SCTPSRVPORT(Optional)
BSC690
BSC690
BSC690
0 SET SCUPORT(Mandatory)
BSC690
0 SET SCUPORT(Optional)
BSC690
0 SET SCUPORT(Optional)
BSC690
0 SET SCUPORT(Mandatory)
BSC690
0 SET SHARETHD(Mandatory)
BSC690
0 SET SHARETHD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET SLFSLVSW(Mandatory)
BSC690
0 SET SLFSLVSW(Optional)
BSC690
BSC690
BSC690
0 SET SNTPCLTPARA(Mandatory)
BSC690 ADD SNTPSRVINFO(Mandatory)
0 RMV SNTPSRVINFO(Optional)
BSC690
0 ADD SNTPSRVINFO(Mandatory)
BSC690 SET
0 SS7PATCHSWITCH(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690
0 SET SSLAUTHMODE(Mandatory)
BSC690 ADD SUBCMD(Optional)
0 RMV SUBCMD(Optional)
BSC690 ADD SUBCMD(Optional)
0 RMV SUBCMD(Optional)
BSC690 ADD SUBCMD(Mandatory)
0 RMV SUBCMD(Mandatory)
BSC690
0 ADD SUBCMD(Mandatory)
BSC690 ADD SUBCMD(Mandatory)
0 RMV SUBCMD(Mandatory)
BSC690
0 SET SUBNET(Mandatory)
BSC690 ADD SUBRACK(Mandatory)
0 RMV SUBRACK(Mandatory)
BSC690 ADD SUBRACK(Mandatory)
0 MOD SUBRACK(Optional)
BSC690 ADD SUBRACK(Optional)
BSC690
0 ADD SUBRACK(Optional)
BSC690 ADD SUBRACK(Optional)
BSC690
0 MOD SUBRACK(Mandatory)
ADD SUBTSK(Optional)
BSC690 RMV SUBTSK(Optional)
0 MOD SUBTSK(Optional)
ADD SUBTSK(Optional)
BSC690 RMV SUBTSK(Optional)
ADD SUBTSK(Mandatory)
BSC690 RMV SUBTSK(Mandatory)
0 MOD SUBTSK(Mandatory)
BSC690
0 ADD SUBTSK(Optional)
BSC690
0 ADD SUBTSK(Mandatory)
BSC690 ADD SUBTSK(Mandatory)

BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET SYS(Optional)
BSC690
0 SET SYS(Optional)
BSC690
0 SET SYS(Optional)
BSC690
0 SET SYS(Optional)
BSC690
0 SET SYS(Optional)
ADD TGWIP(Mandatory)
BSC690 MOD TGWIP(Mandatory)
0 RMV TGWIP(Mandatory)
BSC690 ADD TGWIP(Mandatory)

0 MOD TGWIP(Optional)


BSC690
0 SET TIME(Optional)
BSC690
0 SET TIME(Optional)
BSC690
0 SET TNSOFTPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 TRANSPATCHPARA(Mandatory)
BSC690 SET
0 TRANSPATCHPARA(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0
BSC690 TRANSPATCHPARA(Optional)
0 DEL TRCTASK(Mandatory)
ADD TRMFACTOR(Mandatory)
BSC690 MOD TRMFACTOR(Mandatory)
0 RMV TRMFACTOR(Mandatory)
BSC690 ADD TRMFACTOR(Mandatory)
0 MOD TRMFACTOR(Optional)
BSC690 ADD TRMFACTOR(Optional)































BSC690 ADD TRMLOADTH(Mandatory)

0 RMV TRMLOADTH(Mandatory)
BSC690
0 ADD TRMLOADTH(Mandatory)
BSC690
0 ADD TRMLOADTH(Mandatory)
BSC690
0 ADD TRMLOADTH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD TRMMAP(Mandatory)
BSC690 MOD TRMMAP(Mandatory)
0 RMV TRMMAP(Mandatory)
BSC690 ADD TRMMAP(Optional)
0 MOD TRMMAP(Optional)
BSC690 ADD TRMMAP(Mandatory)

0 MOD TRMMAP(Mandatory)

















































BSC690 ADD TSCROSS(Mandatory)
0 RMV TSCROSS(Mandatory)
BSC690 ADD TSCROSS(Mandatory)
BSC690
0 ADD TSCROSS(Mandatory)
BSC690
BSC690
BSC690
BSC690 ADD TSCROSS(Optional)
BSC690
0 SET TZ(Optional)
BSC690
0 SET TZ(Optional)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
BSC690
0 SET TZ(Mandatory)
ADD U2GNCELL(Mandatory)
BSC690 MOD U2GNCELL(Mandatory)
0 RMV U2GNCELL(Mandatory)
BSC690 ADD U2GNCELL(Optional)
0 MOD U2GNCELL(Optional)




BSC690 ADD U2GNCELL(Mandatory)

0 MOD U2GNCELL(Mandatory)


BSC690 ADD U2GNCELL(Mandatory)

0 MOD U2GNCELL(Mandatory)

BSC690
0 SET UACALGO(Optional)
BSC690
0 SET UACALGO(Mandatory)
BSC690
BSC690
BSC690
0 SET UACALGO(Optional)
BSC690
0 SET UADMCTRL(Mandatory)
BSC690
0 SET UADMCTRL(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD UAICH(Mandatory)
0 RMV UAICH(Mandatory)
BSC690
0 ADD UAICH(Optional)
BSC690 ADD UAICH(Optional)
0 RMV UAICH(Mandatory)
BSC690
BSC690
BSC690 MOD
0 UAICHPWROFFSET(Mandatory)
BSC690 MOD
0 UAICHPWROFFSET(Mandatory)
BSC690
0 SET UALMTHD(Optional)
BSC690
BSC690
BSC690
BSC690
0 SET UAMRC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UAMRCWB(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
SET
BSC690 UAUTONCELLDETECT(Mandator
0 y)
SET
0 y)
BSC690 SET
0 UAUTONCELLDETECT(Optional)
BSC690 SET
SET
0 y)
SET
0 y)
BSC690 SET
SET
0 y)
SET
0 y)
SET
0 y)
BSC690 SET
SET
0 y)
SET
0 y)
SET
0 y)
BSC690 SET
SET
0 y)
SET
0 y)
SET
0 y)
BSC690 SET
SET
0 y)
SET
0 y)
BSC690 SET
SET
0 y)
SET
0 y)
SET
0 y)
SET
0 y)
SET
0 y)
SET
0 y)
SET
0 y)
BSC690 ADD UBCH(Mandatory)
0 RMV UBCH(Mandatory)
BSC690
0 ADD UBCH(Optional)
BSC690
0 ADD UBCH(Optional)
BSC690 SET
0 UCACALGOSWITCH(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0 UCALLSHOCKCTRL(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0 UCAPARATERANGE(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 ADD UCBSADDR(Mandatory)
0 MOD UCBSADDR(Optional)
ADD UCBSADDR(Mandatory)
BSC690 MOD UCBSADDR(Mandatory)
0 RMV UCBSADDR(Mandatory)
0
BSC690 MOD UCBSADDR(Optional)
0
BSC690 ADD UCBSAREA(Mandatory)
0 ADD UCBSAREA(Mandatory)
0 RMV UCBSAREA(Mandatory)
0
BSC690 RMV UCBSAREA(Mandatory)
ADD UCBSMSG(Mandatory)
BSC690 MOD UCBSMSG(Mandatory)
0
BSC690 RMV UCBSMSG(Mandatory)
0 ADD UCBSMSG(Mandatory)
BSC690
BSC690
0 ADD UCBSMSG(Optional)
BSC690 ADD UCBSMSG(Optional)
0 MOD UCBSMSG(Optional)
BSC690
BSC690 ADD UCBSMSG(Mandatory)
BSC690
BSC690
0
ADD UCCP(Mandatory)
BSC690 RMV UCCP(Mandatory)
0 MOD UCCP(Mandatory)
ADD UCCP(Mandatory)
BSC690 RMV UCCP(Mandatory)
BSC690
0 ADD UCCP(Mandatory)
BSC690 ADD UCCP(Mandatory)

BSC690 ADD UCCP(Mandatory)

BSC690
0 ADD UCCP(Optional)
BSC690
BSC690
BSC690
0
BSC690 SET UCDRFILE(Mandatory)
0 SET UCDRFILE(Optional)
ADD UCELLSETUP(Mandatory)
ADD
UCELLQUICKSETUP(Mandatory)
MOD UCELL(Mandatory)
BSC690 MOD UCELLSETUP(Mandatory)
0 RMV UCELL(Mandatory)
BSC690 ADD
0 UCELLQUICKSETUP(Mandatory)
ADD UCELLSETUP(Optional)
ADD
UCELLQUICKSETUP(Optional)
MOD UCELL(Optional)
ADD UIMBCELLSETUP(Optional)
ADD
BSC690 UIMBCELLQUICKSETUP(Optiona
0 l)
ADD
BSC690 UCELLQUICKSETUP(Mandatory)
0 MOD UCELLSETUP(Optional)
ADD
BSC690 UCELLQUICKSETUP(Optional)
0 MOD UCELL(Optional)
ADD
0 MOD UCELL(Mandatory)
BSC690 ADD
BSC690 ADD UCELLSETUP(Optional)
ADD
ADD
ADD



ADD
BSC690 ADD UCELLSETUP(Mandatory)
ADD
BSC690 ADD
ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
0 MOD UCELLSETUP(Mandatory)


ADD
ADD
ADD
ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
0 UCELLQUICKSETUP(Optional)
BSC690 ADD
BSC690 ADD
ADD
ADD
BSC690
BSC690
BSC690
BSC690
ADD
UIMBCELLSETUP(Mandatory)
ADD
BSC690 UIMBCELLQUICKSETUP(Mandat
0 ory)
ADD
ADD
0 ory)
ADD
ADD
0 ory)
ADD
ADD
0 ory)
ADD
ADD
0 ory)
ADD
ADD
0 ory)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
0 l)
ADD
UCELLACCESSSTRICT(Mandator
y)
MOD
y)
RMV
BSC690 UCELLACCESSSTRICT(Mandator
0 y)
ADD
UCELLACCESSSTRICT(Optional)
BSC690 MOD
0 UCELLACCESSSTRICT(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
y)
BSC690 MOD
ADD
MOD
0 y)
ADD
MOD
0 y)
ADD
y)
BSC690 MOD
ADD
MOD
0 y)
ADD
MOD
0 y)
BSC690
0 MOD UCELLACINFO(Mandatory)
BSC690
0 MOD UCELLACINFO(Optional)
BSC690
BSC690
BSC690
0 MOD UCELLACINFO(Mandatory)
ADD
UCELLALGOSWITCH(Mandatory)
MOD
BSC690 RMV
0 UCELLALGOSWITCH(Mandatory)
ADD
UCELLALGOSWITCH(Optional)
BSC690 MOD
0 UCELLALGOSWITCH(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD UCELLAMRC(Mandatory)
BSC690 RMV UCELLAMRC(Mandatory)
0 MOD UCELLAMRC(Mandatory)
BSC690 ADD UCELLAMRC(Optional)

0 MOD UCELLAMRC(Optional)


ADD
UCELLAMRCWB(Mandatory)
MOD
UCELLAMRCWB(Mandatory)
BSC690 RMV
0 UCELLAMRCWB(Mandatory)
BSC690 ADD UCELLAMRCWB(Optional)

0 MOD UCELLAMRCWB(Optional)

ADD UCELLCAC(Mandatory)
BSC690 MOD UCELLCAC(Mandatory)
0 RMV UCELLCAC(Mandatory)
BSC690 ADD UCELLCAC(Optional)
0 MOD UCELLCAC(Optional)























BSC690 ADD UCELLCAC(Mandatory)
0 MOD UCELLCAC(Mandatory)
BSC690 ADD UCELLCAC(Mandatory)

0 MOD UCELLCAC(Mandatory)

BSC690 ADD UCELLCBSDRX(Mandatory)
0 RMV UCELLCBSDRX(Mandatory)
ADD UCELLCBSSAC(Mandatory)
BSC690 MOD UCELLCBSSAC(Mandatory)
0 RMV UCELLCBSSAC(Mandatory)
BSC690 ADD UCELLCBSSAC(Mandatory)
0 MOD UCELLCBSSAC(Mandatory)
0 MOD UCELLCBSSAC(Optional)
BSC690 ADD UCELLCBSSAC(Optional)

0 MOD UCELLCBSSAC(Optional)

0 MOD UCELLCBSSAC(Mandatory)
ADD UCELLCMCF(Mandatory)
BSC690 RMV UCELLCMCF(Mandatory)
0 MOD UCELLCMCF(Mandatory)
BSC690 ADD UCELLCMCF(Optional)

0 MOD UCELLCMCF(Optional)

ADD UCELLDCCC(Mandatory)
BSC690 RMV UCELLDCCC(Mandatory)
0 MOD UCELLDCCC(Mandatory)
BSC690 ADD UCELLDCCC(Optional)
0 MOD UCELLDCCC(Optional)
ADD
UCELLDISTANCEREDIRECTION(
Mandatory)
MOD
Mandatory)
RMV
BSC690 UCELLDISTANCEREDIRECTION(
0 Mandatory)
ADD
Optional)
MOD
0 Optional)
ADD
Optional)
MOD
0 Optional)
ADD
Optional)
MOD
0 Optional)
ADD
Optional)
MOD
0 Optional)
ADD UCELLDRD(Mandatory)
BSC690 MOD UCELLDRD(Mandatory)
0 RMV UCELLDRD(Mandatory)
BSC690 ADD UCELLDRD(Optional)
0 MOD UCELLDRD(Optional)





ADD
UCELLDRDMIMO(Mandatory)
MOD
UCELLDRDMIMO(Mandatory)
BSC690 RMV
0 UCELLDRDMIMO(Mandatory)
BSC690 ADD UCELLDRDMIMO(Optional)
0 MOD UCELLDRDMIMO(Optional)
ADD
UCELLDSACMANUALPARA(Man
datory)
MOD
datory)
RMV
BSC690 UCELLDSACMANUALPARA(Man
0 datory)
ADD
datory)
MOD
datory)
RMV
0 datory)
ADD
datory)
MOD
BSC690 UCELLDSACMANUALPARA(Opti
0 onal)
ADD
datory)
MOD
0 onal)
ADD
datory)
MOD
0 onal)
ADD
datory)
MOD
0 datory)
ADD
datory)
MOD
0 datory)
ADD
datory)
MOD
0 datory)
ADD
datory)
MOD
0 datory)
ADD
UCELLDYNSHUTDOWN(Mandato
ry)
MOD
ry)
RMV
BSC690 UCELLDYNSHUTDOWN(Mandato
0 ry)
ADD
ry)
MOD
BSC690 UCELLDYNSHUTDOWN(Optional
0 )
ADD
ry)
MOD
0 )
ADD
ry)
MOD
0 )
ADD
ry)
MOD
0 )
ADD
ry)
MOD
0 )
ADD
ry)
MOD
0 )
ADD
ry)
MOD
0 )
UCELLDYNSHUTDOWN(Optional
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
ADD UCELLEDRX(Mandatory)
BSC690 MOD UCELLEDRX(Mandatory)
0 RMV UCELLEDRX(Mandatory)
BSC690 ADD UCELLEDRX(Optional)

0 MOD UCELLEDRX(Optional)


ADD UCELLEFACH(Mandatory)
BSC690 MOD UCELLEFACH(Mandatory)
0 RMV UCELLEFACH(Mandatory)
BSC690 ADD UCELLEFACH(Optional)
0 MOD UCELLEFACH(Optional)
ADD UCELLEPCH(Mandatory)
BSC690 MOD UCELLEPCH(Mandatory)
0 RMV UCELLEPCH(Mandatory)
BSC690 ADD UCELLEPCH(Optional)

0 MOD UCELLEPCH(Optional)




RMV UCELLFRC(Mandatory)
BSC690 ADD UCELLFRC(Mandatory)
0 MOD UCELLFRC(Mandatory)
BSC690 ADD UCELLFRC(Optional)

0 MOD UCELLFRC(Optional)


BSC690 ADD UCELLFRC(Mandatory)
0 MOD UCELLFRC(Mandatory)
BSC690 MOD
0 UCELLFREQUENCY(Optional)
BSC690 MOD
0 UCELLFREQUENCY(Mandatory)
BSC690 MOD
0 UCELLFREQUENCY(Mandatory)
BSC690 MOD
BSC690 MOD
BSC690 MOD
ADD
UCELLGPSFRMTIMING(Mandato
ry)
MOD
UCELLGPSFRMTIMING(Mandato
ry)
RMV
BSC690 UCELLGPSFRMTIMING(Mandato
0 ry)
ADD
UCELLGPSFRMTIMING(Optional)
BSC690 MOD
0 UCELLGPSFRMTIMING(Optional)
ADD UCELLHCS(Mandatory)
BSC690 MOD UCELLHCS(Mandatory)
0 RMV UCELLHCS(Mandatory)
BSC690 ADD UCELLHCS(Optional)

0 MOD UCELLHCS(Optional)



ADD UCELLHCSHO(Mandatory)
BSC690 MOD UCELLHCSHO(Mandatory)
0 RMV UCELLHCSHO(Mandatory)
BSC690 ADD UCELLHCSHO(Optional)

0 MOD UCELLHCSHO(Optional)





ADD
UCELLHOCOMM(Mandatory)
MOD
UCELLHOCOMM(Mandatory)
BSC690 RMV
0 UCELLHOCOMM(Mandatory)
BSC690 ADD UCELLHOCOMM(Optional)

0 MOD UCELLHOCOMM(Optional)



BSC690 ADD UCELLHSDPA(Mandatory)
0 MOD UCELLHSDPA(Mandatory)
BSC690 ADD UCELLHSDPA(Optional)

0 MOD UCELLHSDPA(Optional)






0 MOD UCELLHSDPA(Mandatory)

BSC690
0 RMV UCELLHSDPA(Mandatory)
ADD
UCELLHSDPCCH(Mandatory)
MOD
UCELLHSDPCCH(Mandatory)
BSC690 RMV
0 UCELLHSDPCCH(Mandatory)
BSC690 ADD UCELLHSDPCCH(Optional)

0 MOD UCELLHSDPCCH(Optional)
ADD UCELLHSUPA(Mandatory)
BSC690 MOD UCELLHSUPA(Mandatory)
0 RMV UCELLHSUPA(Mandatory)
BSC690 ADD UCELLHSUPA(Optional)
0 MOD UCELLHSUPA(Optional)


BSC690
0 MOD UCELLID(Optional)
BSC690
0 MOD UCELLID(Mandatory)
BSC690
0 MOD UCELLID(Mandatory)
ADD
UCELLINTERFREQHOCOV(Mand
atory)
MOD
UCELLINTERFREQHOCOV(Mand
atory)
RMV
BSC690 UCELLINTERFREQHOCOV(Mand
0 atory)
ADD
UCELLINTERFREQHOCOV(Optio
nal)
MOD
BSC690 UCELLINTERFREQHOCOV(Optio
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
UCELLINTERFREQHONCOV(Ma
ndatory)
MOD
UCELLINTERFREQHONCOV(Ma
ndatory)
RMV
BSC690 UCELLINTERFREQHONCOV(Ma
0 ndatory)
ADD
UCELLINTERFREQHONCOV(Opt
ional)
MOD
BSC690 UCELLINTERFREQHONCOV(Opt
0 ional)
ADD
ional)
MOD
0 ional)
ADD
ional)
MOD
0 ional)
ADD
ional)
MOD
0 ional)
ADD
ional)
MOD
0 ional)
ADD
ional)
MOD
0 ional)
ADD
ional)
MOD
0 ional)
ADD
UCELLINTERRATHOCOV(Manda
tory)
MOD
UCELLINTERRATHOCOV(Manda
tory)
RMV
BSC690 UCELLINTERRATHOCOV(Manda
0 tory)
ADD
UCELLINTERRATHOCOV(Option
al)
MOD
BSC690 UCELLINTERRATHOCOV(Option
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
UCELLINTERRATHONCOV(Mand
atory)
MOD
UCELLINTERRATHONCOV(Mand
atory)
RMV
BSC690 UCELLINTERRATHONCOV(Mand
0 atory)
ADD
UCELLINTERRATHONCOV(Optio
nal)
MOD
BSC690 UCELLINTERRATHONCOV(Optio
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
ADD
nal)
MOD
0 nal)
y)
RMV
UCELLINTRAFREQHO(Mandator
y)
MOD
BSC690 UCELLINTRAFREQHO(Mandator
0 y)
y)
RMV
UCELLINTRAFREQHO(Mandator
y)
MOD
BSC690 UCELLINTRAFREQHO(Mandator
0 y)
ADD
UCELLINTRAFREQHO(Optional)
BSC690 MOD
0 UCELLINTRAFREQHO(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD UCELLLDB(Mandatory)
BSC690 MOD UCELLLDB(Mandatory)
0 RMV UCELLLDB(Mandatory)
BSC690 ADD UCELLLDB(Optional)

0 MOD UCELLLDB(Optional)


ADD UCELLLDM(Mandatory)
BSC690 MOD UCELLLDM(Mandatory)
0 RMV UCELLLDM(Mandatory)
BSC690 ADD UCELLLDM(Optional)

0 MOD UCELLLDM(Optional)









ADD UCELLLDR(Mandatory)
BSC690 MOD UCELLLDR(Mandatory)
0 RMV UCELLLDR(Mandatory)
BSC690 ADD UCELLLDR(Optional)
0 MOD UCELLLDR(Optional)






















ADD UCELLLICENSE(Mandatory)
BSC690 MOD UCELLLICENSE(Mandatory)
0 RMV UCELLLICENSE(Mandatory)
BSC690 ADD UCELLLICENSE(Optional)
0 MOD UCELLLICENSE(Optional)
ADD
UCELLMBDRINTERFREQ(Manda
tory)
MOD
UCELLMBDRINTERFREQ(Manda
tory)
RMV
BSC690 UCELLMBDRINTERFREQ(Manda
0 tory)
ADD
UCELLMBDRINTERFREQ(Option
al)
MOD
BSC690 UCELLMBDRINTERFREQ(Option
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
al)
MOD
0 al)
ADD
UCELLMBDRINTERRAT(Mandato
ry)
MOD
UCELLMBDRINTERRAT(Mandato
ry)
RMV
BSC690 UCELLMBDRINTERRAT(Mandato
0 ry)
UCELLMBDRINTERRAT(Optional
)
MOD
BSC690 UCELLMBDRINTERRAT(Optional
0 )
)
MOD
0 )
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
ADD
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
ADD
)
MOD
0 )
)
MOD
0 )
ADD
UCELLMBMSFACH(Mandatory)
BSC690 RMV
0 UCELLMBMSFACH(Mandatory)
ADD
BSC690 RMV
ADD
BSC690 RMV
BSC690 ADD
0 UCELLMBMSFACH(Optional)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
ADD
UCELLMBMSPARA(Mandatory)
MOD
UCELLMBMSPARA(Mandatory)
BSC690 RMV
0 UCELLMBMSPARA(Mandatory)
ADD
UCELLMBMSPARA(Optional)
BSC690 MOD
0 UCELLMBMSPARA(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690 ADD UCELLMBMSSA(Mandatory)
0 RMV UCELLMBMSSA(Mandatory)
BSC690
0 ADD UCELLMBMSSA(Mandatory)
BSC690 ADD UCELLMBMSSA(Mandatory)
0 RMV UCELLMBMSSA(Mandatory)
ADD
UCELLMBMSSCCPCH(Mandatory
)
MOD
)
RMV
BSC690 UCELLMBMSSCCPCH(Mandatory
0 )
ADD
)
MOD
)
RMV
0 )
ADD
)
MOD
)
RMV
0 )
ADD
UCELLMBMSSCCPCH(Optional)
BSC690 MOD
0 UCELLMBMSSCCPCH(Optional)
ADD UCELLMCCH(Mandatory)
BSC690 MOD UCELLMCCH(Mandatory)
0 RMV UCELLMCCH(Mandatory)
BSC690
0 ADD UCELLMCCH(Mandatory)
BSC690 ADD UCELLMCCH(Optional)
0 MOD UCELLMCCH(Optional)
BSC690
BSC690

ADD UCELLMCDRD(Mandatory)
BSC690 MOD UCELLMCDRD(Mandatory)
0 RMV UCELLMCDRD(Mandatory)
BSC690 ADD UCELLMCDRD(Optional)

0 MOD UCELLMCDRD(Optional)




ADD UCELLMCLDR(Mandatory)
BSC690 MOD UCELLMCLDR(Mandatory)
0 RMV UCELLMCLDR(Mandatory)
BSC690 ADD UCELLMCLDR(Optional)

0 MOD UCELLMCLDR(Optional)

ADD UCELLMEAS(Mandatory)
BSC690 MOD UCELLMEAS(Mandatory)
0 RMV UCELLMEAS(Mandatory)
BSC690 ADD UCELLMEAS(Optional)

0 MOD UCELLMEAS(Optional)

BSC690
0 MOD UCELLNAME(Optional)
BSC690
0 MOD UCELLNAME(Mandatory)
BSC690
0 MOD UCELLNAME(Mandatory)
ADD
UCELLNCLUSTER(Mandatory)
BSC690 RMV
0 UCELLNCLUSTER(Mandatory)
ADD
UCELLNCLUSTER(Mandatory)
BSC690 RMV
0 UCELLNCLUSTER(Mandatory)
ADD
UCELLNFREQPRIOINFO(Mandat
ory)
MOD
ory)
RMV
BSC690 UCELLNFREQPRIOINFO(Mandat
0 ory)
ADD
ory)
MOD
ory)
RMV
BSC690 UCELLNFREQPRIOINFO(Mandat
0 ory)
ADD
ory)
MOD
BSC690 UCELLNFREQPRIOINFO(Optiona
0 l)
ADD
UCELLNFREQPRIOINFO(Optiona
l)
MOD
0 l)
ADD
l)
MOD
0 l)
ADD
l)
MOD
0 l)
ADD
l)
MOD
0 l)
ADD
l)
MOD
0 l)
ADD
l)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD
ory)
MOD
0 l)
ADD UCELLOLC(Mandatory)
BSC690 MOD UCELLOLC(Mandatory)
0 RMV UCELLOLC(Mandatory)
BSC690 ADD UCELLOLC(Optional)

0 MOD UCELLOLC(Optional)






BSC690
0 ADD UCELLOLC(Optional)
BSC690
0 ADD UCELLOLC(Optional)

ADD UCELLPUC(Mandatory)
BSC690 MOD UCELLPUC(Mandatory)
0 RMV UCELLPUC(Mandatory)
BSC690 ADD UCELLPUC(Optional)

0 MOD UCELLPUC(Optional)

MOD UCELLQOSHO(Mandatory)
BSC690 RMV UCELLQOSHO(Mandatory)
0 ADD UCELLQOSHO(Mandatory)
BSC690 MOD UCELLQOSHO(Optional)

0 ADD UCELLQOSHO(Optional)



)
MOD
UCELLQUALITYMEAS(Mandatory
)
RMV
BSC690 UCELLQUALITYMEAS(Mandatory
0 )
ADD
UCELLQUALITYMEAS(Optional)
BSC690 MOD
0 UCELLQUALITYMEAS(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
MOD
0 )
)
MOD
0 )
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
MOD
0 )
)
MOD
0 )
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
MOD
0 )
)
MOD
0 )
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
MOD
0 )
)
MOD
0 )
ADD
UCELLREDIRECTION(Mandatory)
MOD
BSC690 RMV
0 UCELLREDIRECTION(Mandatory)
ADD
MOD
BSC690 RMV
0 UCELLREDIRECTION(Mandatory)
ADD
UCELLREDIRECTION(Optional)
BSC690 MOD
0 UCELLREDIRECTION(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690 ADD
0 UCELLRLACTTIME(Mandatory)
BSC690 RMV
0 UCELLRLACTTIME(Mandatory)
ADD UCELLRLPWR(Mandatory)
BSC690 MOD UCELLRLPWR(Mandatory)
0 RMV UCELLRLPWR(Mandatory)
BSC690 ADD UCELLRLPWR(Mandatory)

0 MOD UCELLRLPWR(Optional)

ADD
UCELLSELRESEL(Mandatory)
MOD
BSC690 RMV
0 UCELLSELRESEL(Mandatory)
BSC690 ADD UCELLSELRESEL(Optional)
0 MOD UCELLSELRESEL(Optional)




ADD
BSC690 MOD
0 UCELLSELRESEL(Mandatory)










ADD
UCELLSIBSWITCH(Mandatory)
MOD
UCELLSIBSWITCH(Mandatory)
BSC690 RMV
0 UCELLSIBSWITCH(Mandatory)
ADD
UCELLSIBSWITCH(Optional)
BSC690 MOD
0 UCELLSIBSWITCH(Optional)
ADD
UCELLU2LTEHONCOV(Mandator
y)
MOD
UCELLU2LTEHONCOV(Mandator
y)
RMV
BSC690 UCELLU2LTEHONCOV(Mandator
0 y)
ADD
UCELLU2LTEHONCOV(Optional)
BSC690 MOD
0 UCELLU2LTEHONCOV(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD UCELLULB(Mandatory)
BSC690 MOD UCELLULB(Mandatory)
0 RMV UCELLULB(Mandatory)
BSC690 ADD UCELLULB(Optional)

0 MOD UCELLULB(Optional)


BSC690 ADD UCELLURA(Mandatory)
0 RMV UCELLURA(Mandatory)
BSC690 ADD UCELLURA(Mandatory)
0 RMV UCELLURA(Mandatory)
BSC690 SET
0 UCHGTHRSHOLD(Mandatory)
BSC690
0 SET UCHGTHRSHOLD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UCHPWROFFSET(Mandatory)
BSC690 RMV
0 UCHPWROFFSET(Mandatory)
BSC690
0 ADD UCHPWROFFSET(Optional)
BSC690
0 ADD UCHPWROFFSET(Optional)
BSC690
0 SET UCHRCTRL(Optional)
BSC690
BSC690
BSC690
BSC690
0 SET UCHRSCOPE(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UCIDCHG(Optional)
BSC690
0 SET UCIDCHG(Optional)
BSC690
0 SET UCMCF(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UCMCF(Mandatory)
BSC690
BSC690
BSC690
ADD UCNDOMAIN(Mandatory)
BSC690 MOD UCNDOMAIN(Mandatory)
0 RMV UCNDOMAIN(Mandatory)
BSC690 ADD UCNDOMAIN(Optional)
0 MOD UCNDOMAIN(Optional)

ADD UCNNODE(Mandatory)
BSC690 MOD UCNNODE(Mandatory)
0 RMV UCNNODE(Mandatory)
ADD UCNNODE(Mandatory)
BSC690 MOD UCNNODE(Mandatory)
0 RMV UCNNODE(Mandatory)
BSC690 ADD UCNNODE(Mandatory)

0 MOD UCNNODE(Mandatory)
0 MOD UCNNODE(Optional)

BSC690 ADD UCNNODE(Optional)





BSC690
0 ADD UCNNODE(Optional)

BSC690
ADD
UCNOPALLCELLBLK(Mandatory)
MOD
BSC690 RMV
0 UCNOPALLCELLBLK(Mandatory)
ADD
BSC690 MOD
0 UCNOPALLCELLBLK(Mandatory)
ADD
BSC690 MOD
0 UCNOPALLCELLBLK(Optional)
ADD
UCNOPERATOR(Mandatory)
BSC690 MOD
0 UCNOPERATOR(Mandatory)
UCNOPERATOR(Mandatory)
BSC690 MOD
BSC690 ADD
BSC690 ADD
BSC690
0 ADD UCNOPERATOR(Optional)
BSC690 MOD
BSC690 RMV
ADD
UCNOPERGROUP(Mandatory)
MOD
BSC690 RMV
0 UCNOPERGROUP(Mandatory)
ADD
BSC690 MOD
0 UCNOPERGROUP(Optional)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690
0 ADD UCNOPERGROUP(Optional)
BSC690
0 SET UCNTCHK(Optional)
BSC690
0 SET UCNTCHK(Mandatory)
BSC690
0 SET UCOIFTIMER(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UCONNMODETIMER(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
SET
BSC690 UCORRMALGOSWITCH(Optional
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )SET
0 )
SET
0 )
SET
0 )
SET
0 )
BSC690
0 SET UCORRMPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UCPUSSHARETHD(Optional)
BSC690 ADD UCTCH(Mandatory)
0 RMV UCTCH(Mandatory)
BSC690 ADD UCTCH(Mandatory)
0 RMV UCTCH(Mandatory)
BSC690 SET
0 UCTRLPLNFCPARA(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
SET
BSC690 UCTRLPLNSHAREPARA(Optional
0 )
SET
0 )
SET
0 )
SET
0 )
SET
0 )
BSC690 ADD UCZ(Mandatory)
0 RMV UCZ(Mandatory)
BSC690
0 ADD UCZ(Mandatory)
BSC690
0 ADD UCZ(Mandatory)
BSC690 ADD UCZ(Mandatory)
0 RMV UCZ(Mandatory)
BSC690
0 SET UDCCC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UDCCC(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET UDCCC(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UDEVICETYPEIMSI(Mandatory)
BSC690 RMV
0 UDEVICETYPEIMSI(Mandatory)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
0 UDEVICETYPEIMSI(Optional)
ADD
UDEVICETYPEPRIOGROUP(Man
datory)
MOD
UDEVICETYPEPRIOGROUP(Man
datory)
RMV
BSC690 UDEVICETYPEPRIOGROUP(Man
0 datory)
ADD
UDEVICETYPEPRIOGROUP(Opti
onal)
MOD
BSC690 UDEVICETYPEPRIOGROUP(Opti
0 onal)
ADD
onal)
MOD
0 onal)
ADD
onal)
MOD
0 onal)
SET
BSC690 UDISTANCEREDIRECTION(Optio
0 nal)
SET
0 nal)
SET
0 nal)
SET
0 nal)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UDRD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UDRDMIMO(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UDRDMIMO(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET UDRDMIMO(Mandatory)
BSC690 SET
0 UDSACAUTOALGO(Optional)
BSC690 SET
0 UDSACAUTOALGO(Mandatory)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690
0 SET UDSSPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UDTXDRXPARA(Mandatory)
BSC690
0 SET UDTXDRXPARA(Mandatory)
BSC690
0 SET UDTXDRXPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UE2EQOSPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
SET
BSC690 UEDCHRATEADJUSTSET(Option
0 al)
BSC690
0 SET UEDCHTTIRECFG(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UERACHACTOASCMAP(Mandato
ry)
RMV
BSC690 UERACHACTOASCMAP(Mandato
0 ry)
ADD
0 )ADD
0 )ADD
0 )
ADD
0 )ADD
0 )ADD
0 )ADD
0 )
ADD UERACHASC(Mandatory)
BSC690 RMV UERACHASC(Mandatory)
0 MOD UERACHASC(Mandatory)
BSC690 ADD UERACHASC(Optional)
0 MOD UERACHASC(Optional)

ADD UERACHBASIC(Mandatory)
BSC690 MOD UERACHBASIC(Mandatory)
0 RMV UERACHBASIC(Mandatory)
BSC690 ADD UERACHBASIC(Mandatory)
0 MOD UERACHBASIC(Mandatory)
BSC690 ADD UERACHBASIC(Optional)
0 MOD UERACHBASIC(Optional)



ADD UEXT2GCELL(Mandatory)
BSC690 RMV UEXT2GCELL(Mandatory)
0 MOD UEXT2GCELL(Mandatory)
BSC690 ADD UEXT2GCELL(Mandatory)
0 MOD UEXT2GCELL(Optional)


BSC690 ADD UEXT2GCELL(Optional)





BSC690
0 ADD UEXT3GCELL(Mandatory)
BSC690
0 ADD UEXT3GCELL(Mandatory)









BSC690
0 ADD UEXT3GCELL(Optional)

ADD UFACH(Mandatory)
BSC690 RMV UFACH(Mandatory)
0 MOD UFACH(Mandatory)
BSC690
0 ADD UFACH(Mandatory)
ADD UFACH(Mandatory)
BSC690 RMV UFACH(Mandatory)
0 MOD UFACH(Mandatory)
BSC690
0 ADD UFACH(Optional)
BSC690
BSC690
BSC690 ADD UFACH(Optional)

0 MOD UFACH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UFACHBANDWIDTH(Mandatory)
BSC690 SET
0 UFACHBANDWIDTH(Mandatory)
BSC690 SET
0 UFACHBANDWIDTH(Optional)
BSC690 ADD UFACHDYNTFS(Mandatory)
0 RMV UFACHDYNTFS(Mandatory)
BSC690
0 ADD UFACHDYNTFS(Mandatory)
BSC690
0 ADD UFACHDYNTFS(Optional)
BSC690
BSC690
BSC690 ADD UFACHLOCH(Mandatory)
0 RMV UFACHLOCH(Mandatory)
BSC690 ADD UFACHLOCH(Mandatory)
0 RMV UFACHLOCH(Mandatory)
BSC690
0 SET UFDPCHPARA(Optional)
BSC690
0 SET UFDPCHRLPWR(Optional)
BSC690
0 SET UFDPCHRLPWR(Optional)
BSC690
0 SET UFRC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UFRC(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UFRCCHLTYPEPARA(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 ADD UGIPORT(Mandatory)
0 RMV UGIPORT(Mandatory)
BSC690
0 ADD UGIPORT(Mandatory)
BSC690
0 ADD UGIPORT(Mandatory)
BSC690
0 SET UGTPU(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UHCSHO(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UHOCOMM(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UHSDPCCH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
SET
BSC690 UHSSCCHLESSOPPARA(Mandat
0 ory)
SET
0 ory)
SET
0 ory)
SET
BSC690 UHSSCCHLESSOPPARA(Optiona
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
BSC690 SET
0 UIDLEMODETIMER(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 RMV UIMBCELL(Mandatory)
0 MOD UIMBCELL(Mandatory)
BSC690
0 MOD UIMBCELL(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD UIMBCLUSTER(Mandatory)
BSC690 RMV UIMBCLUSTER(Mandatory)
0 MOD UIMBCLUSTER(Mandatory)
BSC690
0 ADD UIMBCLUSTER(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD UIMBCLUSTER(Optional)
0 MOD UIMBCLUSTER(Optional)
ADD
UIMBCLUSTERMBMSSA(Mandat
ory)
RMV
BSC690 UIMBCLUSTERMBMSSA(Mandat
0 ory)
ADD
ory)
RMV
0 ory)
ADD
ory)
RMV
0 ory)
ADD
UIMBCLUSTERMCCH(Mandatory)
BSC690 RMV
0 UIMBCLUSTERMCCH(Mandatory)
BSC690
0 SET UIMBFACH(Mandatory)
BSC690
0 SET UIMBFACH(Mandatory)
BSC690
0 SET UIMBFACH(Optional)
BSC690
0 SET UIMBFACH(Optional)
UIMBNCLUSTER(Mandatory)
BSC690 RMV
0 UIMBNCLUSTER(Mandatory)
UIMBNCLUSTER(Mandatory)
BSC690 RMV
0 UIMBNCLUSTER(Mandatory)
ADD
UIMBSERVICECH(Mandatory)
BSC690 RMV
0 UIMBSERVICECH(Mandatory)
ADD
UIMBSERVICECH(Mandatory)
BSC690 RMV
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690
0 ADD UIMBSERVICECH(Optional)
BSC690
0 ADD UIMBSERVICECH(Optional)
BSC690
0 SET UIMBSWITCH(Optional)
ADD UIMEITAC(Mandatory)
BSC690 MOD UIMEITAC(Mandatory)
0 RMV UIMEITAC(Mandatory)
ADD UIMEITAC(Mandatory)
BSC690 MOD UIMEITAC(Mandatory)
0 RMV UIMEITAC(Mandatory)
BSC690 ADD UIMEITAC(Mandatory)
0 MOD UIMEITAC(Optional)
BSC690 ADD UIMEITAC(Optional)
BSC690 ADD UIMEITAC(Optional)

UIMSIIDNNSCNIDMAP(Mandator
y)
RMV
BSC690 UIMSIIDNNSCNIDMAP(Mandator
0 y)
y)
RMV
0 y)
y)
RMV
0 y)
y)
RMV
0 y)
BSC690 ADD UIMSISNAMAP(Mandatory)
0 RMV UIMSISNAMAP(Mandatory)
BSC690
0 ADD UIMSISNAMAP(Mandatory)
BSC690
0 ADD UIMSISNAMAP(Mandatory)

BSC690
BSC690
BSC690 SET
0 UINTERFREQHOCOV(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0 UINTERFREQHONCOV(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
ADD
UINTERFREQNCELL(Mandatory)
RMV
BSC690 MOD
0 UINTERFREQNCELL(Mandatory)
ADD
RMV
BSC690 MOD
ADD
RMV
BSC690 MOD
ADD
RMV
BSC690 MOD
ADD
UINTERFREQNCELL(Optional)
BSC690 MOD
0 UINTERFREQNCELL(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690 SET
0 UINTERRATHOCOV(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0 UINTERRATHONCOV(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690
0 SET UINTRAFREQHO(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UINTRAFREQNCELL(Mandatory)
RMV
BSC690 MOD
0 UINTRAFREQNCELL(Mandatory)
ADD
RMV
BSC690 MOD
ADD
RMV
BSC690 MOD
ADD
RMV
BSC690 MOD
ADD
UINTRAFREQNCELL(Optional)
BSC690 MOD
0 UINTRAFREQNCELL(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD UIPDL(Mandatory)
BSC690 MOD UIPDL(Mandatory)
0 RMV UIPDL(Mandatory)
BSC690 ADD UIPDL(Mandatory)
0 MOD UIPDL(Optional)
ADD
UIPSERVICEQOS(Mandatory)
MOD
BSC690 RMV
0 UIPSERVICEQOS(Mandatory)
ADD UIPSERVICEQOS(Optional)
MOD
BSC690 RMV
BSC690 ADD UIPSERVICEQOS(Optional)

0 MOD UIPSERVICEQOS(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690 ADD UIPSERVICEQOS(Optional)

0 MOD UIPSERVICEQOS(Optional)
ADD
BSC690 UIURCOMMSCCP(Mandatory)
0 MOD UIURCOMMSCCP(Optional)
ADD
BSC690 UIURCOMMSCCP(Mandatory)
0 MOD UIURCOMMSCCP(Optional)
ADD UIURGCONN(Mandatory)
BSC690 RMV UIURGCONN(Mandatory)
0 MOD UIURGCONN(Mandatory)
BSC690 ADD UIURGCONN(Mandatory)
0 MOD UIURGCONN(Optional)
BSC690 SET
0 UIUTIMERANDNUM(Mandatory)
BSC690 SET
0 UIUTIMERANDNUM(Mandatory)
BSC690 SET
0 UIUTIMERANDNUM(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690
0 SET UKPIALMTHD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UKPISELFCUREPARA(Optional)
BSC690 SET
0 UKPISELFCUREPARA(Optional)
BSC690 ADD ULAC(Mandatory)
0 RMV ULAC(Mandatory)
BSC690 ADD ULAC(Mandatory)
0 RMV ULAC(Mandatory)
BSC690
0 ADD ULAC(Mandatory)
BSC690
0 ADD ULAC(Mandatory)
BSC690
0 ADD ULASNAMAP(Mandatory)
BSC690 ADD ULASNAMAP(Mandatory)
0 RMV ULASNAMAP(Mandatory)

BSC690
BSC690
0 SET ULDCALGOPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET ULDCPERIOD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET ULDM(Optional)
BSC690
BSC690
0 SET ULDM(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD ULOCELL(Mandatory)
0 RMV ULOCELL(Mandatory)
BSC690 ADD ULOCELL(Mandatory)
0 RMV ULOCELL(Mandatory)
ADD ULTECELL(Mandatory)
BSC690 MOD ULTECELL(Mandatory)
0 RMV ULTECELL(Mandatory)
BSC690 ADD ULTECELL(Mandatory)

0 MOD ULTECELL(Optional)







BSC690 ADD ULTECELL(Optional)

BSC690 ADD ULTECELL(Optional)

ADD ULTENCELL(Mandatory)
BSC690 MOD ULTENCELL(Mandatory)
0 RMV ULTENCELL(Mandatory)
BSC690 SET
0 UMBMSALARMPARA(Mandatory)
ADD
UMBMSALARMSERVICE(Mandat
ory)
RMV
BSC690 UMBMSALARMSERVICE(Mandat
0 ory)
ADD
ory)
RMV
0 ory)
ADD
ory)
RMV
0 ory)
BSC690
0 SET UMBMSFACH(Mandatory)
BSC690
0 SET UMBMSFACH(Mandatory)
BSC690
0 SET UMBMSFACH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UMBMSPERF(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690 ADD UMBMSSA(Mandatory)
0 RMV UMBMSSA(Mandatory)
BSC690 ADD UMBMSSA(Mandatory)
0 RMV UMBMSSA(Mandatory)
BSC690 SET
0 UMBMSSCCPCH(Mandatory)
BSC690 SET
0 UMBMSSCCPCH(Mandatory)
BSC690
0 SET UMBMSSCCPCH(Optional)
BSC690
0 SET UMBMSSWITCH(Mandatory)
BSC690
0 SET UMBMSSWITCH(Optional)
BSC690
BSC690
BSC690
0 SET UMBSCCRRM(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UMCCHPERIODCOEF(Optional)
BSC690 SET
BSC690 SET
BSC690
0 SET UMCDRD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UMCLDR(Optional)
BSC690
BSC690
BSC690
BSC690
0 SET UMGWTST(Mandatory)
BSC690
0 SET UMGWTST(Mandatory)
BSC690
0 SET UMSCHFACH(Optional)
BSC690
0 SET UMTCH(Mandatory)
BSC690
0 SET UMTCH(Mandatory)
BSC690
0 SET UMTCH(Optional)
BSC690
0 SET UNATALG(Mandatory)
BSC690
BSC690
BSC690 ADD UNATRESPOOL(Mandatory)
0 RMV UNATRESPOOL(Mandatory)
BSC690
0 ADD UNATRESPOOL(Mandatory)
BSC690
0
0
0 ADD UNATRESPOOL(Mandatory)
BSC690
0 SET UNATSWITCH(Mandatory)
BSC690
0 SET UNBMPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UNBNODESYNCMONPARA(Man
datory)
MOD
datory)
RMV
BSC690 UNBNODESYNCMONPARA(Man
0 datory)
ADD
datory)
MOD
BSC690 UNBNODESYNCMONPARA(Opti
0 onal)
ADD
datory)
MOD
BSC690 UNBNODESYNCMONPARA(Opti
0 onal)
BSC690 ADD UNBSC(Mandatory)
0 RMV UNBSC(Mandatory)
SET
BSC690 UNCELLDETECTSWITCH(Manda
0 tory)
SET
BSC690 UNCELLDETECTSWITCH(Manda
0 tory)
SET
BSC690 UNCELLDETECTSWITCH(Option
0 al)
SET
0 al)
SET
0 al)
ADD UNCP(Mandatory)
BSC690 RMV UNCP(Mandatory)
0 MOD UNCP(Mandatory)
BSC690
0 ADD UNCP(Mandatory)
BSC690 ADD UNCP(Mandatory)

BSC690 ADD UNCP(Mandatory)

BSC690
0 ADD UNCP(Optional)
BSC690
BSC690
ADD UNILNK(Mandatory)
BSC690 MOD UNILNK(Mandatory)
0 RMV UNILNK(Mandatory)
BSC690 ADD UNILNK(Optional)
0 MOD UNILNK(Optional)
0 MOD UNILNK(Mandatory)
BSC690 ADD UNILNK(Mandatory)
0 MOD UNILNK(Mandatory)
BSC690 ADD UNODEB(Mandatory)
0 RMV UNODEB(Mandatory)
0 MOD UNODEB(Mandatory)
BSC690
0 ADD UNODEB(Mandatory)
BSC690
0 ADD UNODEB(Mandatory)
BSC690
0 ADD UNODEB(Optional)
BSC690 ADD UNODEB(Optional)

0 MOD UNODEB(Optional)
BSC690
0 ADD UNODEB(Optional)
ADD
UNODEBALGOPARA(Mandatory)
MOD
UNODEBALGOPARA(Mandatory)
BSC690 RMV
0 UNODEBALGOPARA(Mandatory)
ADD
UNODEBALGOPARA(Optional)
BSC690 MOD
0 UNODEBALGOPARA(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
MOD UNODEBESN(Mandatory)
BSC690 RMV UNODEBESN(Mandatory)
0 ADD UNODEBESN(Mandatory)
BSC690 MOD UNODEBESN(Optional)


0 ADD UNODEBESN(Optional)
BSC690 MOD UNODEBESN(Mandatory)


0 ADD UNODEBESN(Optional)

MOD UNODEBIP(Mandatory)
BSC690 RMV UNODEBIP(Mandatory)
0 ADD UNODEBIP(Mandatory)
BSC690 MOD UNODEBIP(Mandatory)
BSC690 MOD UNODEBIP(Optional)









0 ADD UNODEBIP(Optional)


ADD UNODEBLDR(Mandatory)
BSC690 MOD UNODEBLDR(Mandatory)
0 RMV UNODEBLDR(Mandatory)
BSC690 ADD UNODEBLDR(Optional)

0 MOD UNODEBLDR(Optional)












BSC690
0 MOD UNODEBNAME(Mandatory)
BSC690
0 MOD UNODEBNAME(Mandatory)
ADD UNODEBOLC(Mandatory)
BSC690 MOD UNODEBOLC(Mandatory)
0 RMV UNODEBOLC(Mandatory)
BSC690 ADD UNODEBOLC(Optional)
0 MOD UNODEBOLC(Optional)
BSC690 ADD UNODEBOLC(Optional)
0 MOD UNODEBOLC(Optional)
BSC690
0 RMV UNRELATION(Optional)
BSC690
0 RMV UNRELATION(Mandatory)
BSC690
0 RMV UNRELATION(Mandatory)
ADD
UNRIGLBCNIDMAP(Mandatory)
BSC690 RMV
0 UNRIGLBCNIDMAP(Mandatory)
ADD
BSC690 RMV
ADD
BSC690 RMV
ADD UNRNC(Mandatory)
BSC690 MOD UNRNC(Mandatory)
0 RMV UNRNC(Mandatory)
BSC690 ADD UNRNC(Mandatory)
0 MOD UNRNC(Optional)


0 MOD UNRNC(Mandatory)
BSC690 ADD UNRNC(Optional)



0 MOD UNRNC(Mandatory)

BSC690 ADD UNRNCURA(Mandatory)

0 RMV UNRNCURA(Mandatory)
BSC690 ADD UNRNCURA(Mandatory)
0 RMV UNRNCURA(Mandatory)
BSC690
0 ADD UNRNCURA(Mandatory)
BSC690 ADD UOFFLOAD(Mandatory)
0 RMV UOFFLOAD(Mandatory)
BSC690 ADD UOFFLOAD(Optional)
0 MOD UOFFLOAD(Optional)
BSC690
0 ADD UOFFLOAD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 MOD UOFFLOAD(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD UOFFLOADAPN(Mandatory)
0 RMV UOFFLOADAPN(Mandatory)
BSC690
0 ADD UOFFLOADAPN(Mandatory)
BSC690
0 ADD UOFFLOADAPN(Mandatory)
ADD
UOFFLOADIMEITAC(Mandatory)
BSC690 RMV
0 UOFFLOADIMEITAC(Mandatory)
BSC690 ADD
0 UOFFLOADIMEITAC(Mandatory)
BSC690 ADD UOFFLOADIMSI(Mandatory)
0 RMV UOFFLOADIMSI(Mandatory)
ADD UOFFLOADRAB(Mandatory)
BSC690 MOD UOFFLOADRAB(Mandatory)
0 RMV UOFFLOADRAB(Mandatory)
ADD UOFFLOADRAB(Mandatory)
BSC690 MOD UOFFLOADRAB(Mandatory)
0 RMV UOFFLOADRAB(Mandatory)
BSC690 ADD UOFFLOADRAB(Mandatory)
0 MOD UOFFLOADRAB(Mandatory)
SET
BSC690 UOPERATORCFGPARA(Mandato
0 ry)
SET
BSC690 UOPERATORCFGPARA(Optional
0 )
SET
0 )
SET
0 )
SET
0 ry)
SET
0 ry)
SET
0 )
SET
0 )
SET
0 )
SET
0 ry)
SET
0 ry)
SET
BSC690 UOPERATORSHARINGMODE(O
0 ptional)
SET
0 ptional)
SET
0 ptional)
SET
0 ptional)
SET
0 ptional)
SET
0 ptional)
ADD
UOPERCAPARATERANGE(Mand
atory)
RMV
BSC690 UOPERCAPARATERANGE(Mand
0 atory)
ADD
BSC690 UOPERCAPARATERANGE(Optio
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
0 nal)
ADD
UOPERSCHEDULEPRIOMAP(Ma
ndatory)
RMV
BSC690 UOPERSCHEDULEPRIOMAP(Ma
0 ndatory)
ADD
ndatory)
RMV
0 ndatory)
ADD
ndatory)
RMV
0 ndatory)
ADD
ndatory)
RMV
0 ndatory)
ADD
0 ndatory)
ADD
UOPERSPIWEIGHT(Mandatory)
BSC690 RMV
0 UOPERSPIWEIGHT(Mandatory)
ADD
UOPERSPIWEIGHT(Mandatory)
BSC690 RMV
0 UOPERSPIWEIGHT(Mandatory)
BSC690 ADD
0 UOPERSPIWEIGHT(Optional)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD
ADD
UOPERTHPCLASS(Mandatory)
MOD
UOPERTHPCLASS(Mandatory)
BSC690 RMV
0 UOPERTHPCLASS(Mandatory)
ADD
UOPERTHPCLASS(Optional)
BSC690 MOD
0 UOPERTHPCLASS(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
UOPERUSERGBR(Mandatory)
MOD
BSC690 RMV
0 UOPERUSERGBR(Mandatory)
ADD
MOD
BSC690 RMV
ADD
MOD
BSC690 RMV
ADD
MOD
BSC690 RMV
ADD
MOD
BSC690 RMV
BSC690 ADD UOPERUSERGBR(Optional)

0 MOD UOPERUSERGBR(Optional)
BSC690 ADD UOPERUSERGBR(Optional)

0 MOD UOPERUSERGBR(Optional)
ADD
UOPERUSERHAPPYBR(Mandato
ry)
RMV
BSC690 UOPERUSERHAPPYBR(Mandato
0 ry)
ADD
ry)
RMV
0 ry)
ADD
ry)
RMV
0 ry)
ADD
ry)
RMV
0 ry)
BSC690 ADD
0 UOPERUSERHAPPYBR(Optional)
ADD
UOPERUSERPRIORITY(Mandato
ry)
MOD
UOPERUSERPRIORITY(Mandato
ry)
RMV
BSC690 UOPERUSERPRIORITY(Mandato
0 ry)
ADD
UOPERUSERPRIORITY(Optional)
BSC690 MOD
0 UOPERUSERPRIORITY(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
BSC690 ADD UPCCPCH(Mandatory)
0 RMV UPCCPCH(Mandatory)
BSC690
0 ADD UPCCPCH(Optional)
BSC690 ADD UPCH(Mandatory)
0 RMV UPCH(Mandatory)
BSC690
0 ADD UPCH(Mandatory)
BSC690 ADD UPCH(Optional)
0 RMV UPCH(Mandatory)
BSC690
0 ADD UPCH(Optional)
BSC690
BSC690
BSC690
BSC690 ADD UPCHDYNTFS(Mandatory)
0 RMV UPCHDYNTFS(Mandatory)
BSC690 ADD UPCHDYNTFS(Optional)
BSC690 ADD UPCHDYNTFS(Mandatory)
BSC690
0 ADD UPCHDYNTFS(Mandatory)
BSC690
0 ADD UPCHDYNTFS(Optional)
BSC690
0 ADD UPCHDYNTFS(Optional)
BSC690 ADD UPCPICH(Mandatory)
0 RMV UPCPICH(Mandatory)
BSC690
0 ADD UPCPICH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 MOD UPCPICHPWR(Mandatory)
BSC690
0 MOD UPCPICHPWR(Optional)
BSC690
0 MOD UPCPICHPWR(Optional)
BSC690 SET
0 UPERIODICRTTLCS(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 ADD UPICH(Mandatory)
0 RMV UPICH(Mandatory)
BSC690
0 ADD UPICH(Mandatory)
BSC690 ADD UPICH(Optional)
0 RMV UPICH(Mandatory)
BSC690
0 ADD UPICH(Optional)
BSC690
0 ADD UPICH(Optional)
BSC690 MOD
0 UPICHPWROFFSET(Mandatory)
BSC690 MOD
0 UPICHPWROFFSET(Mandatory)
MOD
BSC690 UPLMNVALTAGRANGE(Mandato
0 ry)
MOD
0 ry)
MOD
0 ry)
MOD
0 ry)
BSC690 MOD
0 UPLMNVALTAGRANGE(Optional)
BSC690 MOD
0 UPLMNVALTAGRANGE(Optional)
SET
BSC690 UPOOLPRIMHOSTPOLICY(Optio
0 nal)
SET
BSC690 UPOOLPRIMHOSTPOLICY(Mand
0 atory)
SET
BSC690 UPOOLPRIMHOSTPOLICY(Mand
0 atory)
BSC690 MOD UPRACH(Mandatory)
0 RMV UPRACH(Mandatory)
BSC690 MOD UPRACH(Mandatory)
0 RMV UPRACH(Mandatory)
BSC690
0 MOD UPRACH(Optional)
BSC690
0 MOD UPRACH(Optional)
ADD
UPRACHACTOASCMAP(Mandato
ry)
MOD
ry)
RMV
BSC690 UPRACHACTOASCMAP(Mandato
0 ry)
ADD
UPRACHACTOASCMAP(Optional
)
MOD
ry)
RMV
BSC690 UPRACHACTOASCMAP(Mandato
0 ry)
)
MOD
BSC690 UPRACHACTOASCMAP(Optional
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
)
MOD
0 )
ADD UPRACHASC(Mandatory)
BSC690 MOD UPRACHASC(Mandatory)
0 RMV UPRACHASC(Mandatory)
ADD UPRACHASC(Optional)
ADD UPRACHASC(Mandatory)
BSC690 ADD UPRACHASC(Optional)
0 MOD UPRACHASC(Optional)

BSC690
0 ADD UPRACHASC(Mandatory)
BSC690
0 ADD UPRACHBASIC(Mandatory)
BSC690
0 ADD UPRACHBASIC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
UPRACHSLOTFORMAT(Mandato
ry)
RMV
BSC690 UPRACHSLOTFORMAT(Mandato
0 ry)
ADD
UPRACHSLOTFORMAT(Optional)
RMV
0 ry)
ADD
0 ry)
BSC690 ADD
0 UPRACHSLOTFORMAT(Optional)
BSC690 ADD
BSC690 ADD
BSC690 ADD
BSC690 ADD UPRACHTFC(Mandatory)
0 RMV UPRACHTFC(Mandatory)
BSC690 ADD UPRACHTFC(Optional)
BSC690 ADD UPRACHTFC(Mandatory)
BSC690
0 ADD UPRACHTFC(Mandatory)
BSC690
0 ADD UPRACHTFC(Mandatory)
BSC690
0 ADD UPRACHTFC(Optional)
BSC690 MOD
0 UPRACHUUPARAS(Mandatory)
BSC690 MOD
0 UPRACHUUPARAS(Mandatory)
BSC690 MOD
0 UPRACHUUPARAS(Optional)
BSC690 MOD
BSC690 MOD
BSC690 ADD UPSCH(Mandatory)
0 RMV UPSCH(Mandatory)
BSC690
0 ADD UPSCH(Optional)
BSC690
0 ADD UPSCH(Optional)
BSC690
0 SET UPSINACTTIMER(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UPTTPARAM(Optional)
BSC690
BSC690
BSC690
BSC690 SET
0 UPTTSTATETRANS(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
0
BSC690 UPTTSTATETRANS(Optional)
SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690
0 SET UQOSACT(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UQOSHO(Optional)
BSC690
BSC690
BSC690
BSC690
0 SET UQUALITYMEAS(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UQUALITYMEAS(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 SET
0 UQUEUEPREEMPT(Optional)
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 SET
BSC690 ADD URAC(Mandatory)
0 RMV URAC(Mandatory)
BSC690
0 ADD URAC(Mandatory)
BSC690
0 ADD URAC(Mandatory)
ADD URACH(Mandatory)
BSC690 MOD URACH(Mandatory)
0 RMV URACH(Mandatory)
BSC690
0 ADD URACH(Optional)
ADD URACH(Optional)
BSC690 MOD URACH(Mandatory)
0 RMV URACH(Mandatory)
BSC690
0 ADD URACH(Optional)
BSC690 ADD URACH(Optional)
0 MOD URACH(Optional)

BSC690 ADD URACHDYNTFS(Mandatory)
0 RMV URACHDYNTFS(Mandatory)
BSC690 ADD URACHDYNTFS(Optional)
BSC690 ADD URACHDYNTFS(Mandatory)
BSC690
0 ADD URACHDYNTFS(Mandatory)
BSC690
0 ADD URACHDYNTFS(Optional)
BSC690
0 ADD
SET URACHDYNTFS(Optional)
BSC690 URACHMEASUREPARA(Optional
0 )
SET
0 )SET
0 )SET
0 )SET
0 )SET
0 )
SET
0 )
BSC690
0 SET UREDIRECTION(Mandatory)
BSC690
0 SET UREDIRECTION(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD
URESERVEOVSF(Mandatory)
BSC690 RMV
0 URESERVEOVSF(Mandatory)
ADD
URESERVEOVSF(Mandatory)
BSC690 RMV
BSC690 ADD
BSC690
0 RMV URESERVEOVSF(Optional)
ADD
URNCALLCELLBLK(Mandatory)
BSC690 MOD
0 URNCALLCELLBLK(Optional)
ADD
URNCALLCELLBLK(Mandatory)
BSC690 MOD
0 URNCALLCELLBLK(Optional)
BSC690 ADD URNCBASIC(Mandatory)

0 MOD URNCBASIC(Optional)
BSC690 ADD URNCBASIC(Mandatory)

0 MOD URNCBASIC(Optional)
BSC690 ADD URNCCBCPUID(Mandatory)
0 RMV URNCCBCPUID(Mandatory)
BSC690
0 ADD URNCCBCPUID(Mandatory)
BSC690
BSC690
BSC690
0
BSC690 SET URNCCBPARA(Optional)
0 SET URNCCBPARA(Optional)
BSC690
BSC690
BSC690
SET
BSC690 URNCCELLSHUTDOWNPARA(O
0 ptional)
SET
0 ptional)
SET
0 ptional)
BSC690
0 SET URNCMBMSPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD URNCPOOL(Mandatory)
BSC690 MOD URNCPOOL(Mandatory)
0 RMV URNCPOOL(Mandatory)
BSC690 ADD URNCPOOL(Mandatory)
0 MOD URNCPOOL(Optional)
BSC690 ADD URNCPOOL(Optional)

ADD
URNCPOOLMEMBER(Mandatory)
BSC690 RMV
0 URNCPOOLMEMBER(Mandatory)
ADD
URNCPOOLMEMBER(Mandatory)
BSC690 RMV
0 URNCPOOLMEMBER(Mandatory)
BSC690 ADD UROAMMAP(Mandatory)
0 RMV UROAMMAP(Mandatory)
BSC690
0 ADD UROAMMAP(Mandatory)
BSC690 SET
0 URRCESTCAUSE(Mandatory)
BSC690
0 SET URRCESTCAUSE(Optional)
BSC690
0 SET URRCESTCAUSE(Optional)
ADD
URRCESTCAUSESIGCHTYPE(M
andatory)
MOD
URRCESTCAUSESIGCHTYPE(M
andatory)
RMV
BSC690 URRCESTCAUSESIGCHTYPE(M
0 andatory)
ADD
URRCESTCAUSESIGCHTYPE(O
ptional)
MOD
BSC690 URRCESTCAUSESIGCHTYPE(O
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
ADD
ptional)
MOD
0 ptional)
BSC690
0 SET URRCTRLSWITCH(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET URRRSVDPARA(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD USAC(Mandatory)
0 RMV USAC(Mandatory)
ADD
USAMBMSPARA(Mandatory)
MOD
BSC690 RMV
0 USAMBMSPARA(Mandatory)
ADD
MOD
BSC690 RMV
0 USAMBMSPARA(Mandatory)
BSC690 ADD USAMBMSPARA(Optional)

0 MOD USAMBMSPARA(Optional)

BSC690 ADD USAS(Mandatory)
0 MOD USAS(Mandatory)
BSC690 ADD USAS(Mandatory)
0 MOD USAS(Mandatory)
BSC690
0 ADD USAS(Mandatory)
BSC690 ADD USAS(Optional)
0 MOD USAS(Optional)
BSC690
0 RMV USAS(Mandatory)
BSC690
0 MOD USAS(Optional)
BSC690
0 SET USATLDCPERIOD(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET USATLDM(Optional)
BSC690
BSC690
0 SET USATLDM(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 MOD USCCPCH(Mandatory)
0 RMV USCCPCH(Mandatory)
BSC690 MOD USCCPCH(Mandatory)
0 RMV USCCPCH(Mandatory)
BSC690
0 MOD USCCPCH(Optional)
BSC690
0 MOD USCCPCH(Optional)
BSC690 ADD
0 USCCPCHBASIC(Mandatory)
BSC690 ADD
BSC690
0 ADD USCCPCHBASIC(Optional)
BSC690 ADD
BSC690
BSC690
BSC690 ADD
BSC690 ADD
BSC690
BSC690 ADD USCCPCHTFC(Mandatory)
0 RMV USCCPCHTFC(Mandatory)
SET
BSC690 USCHEDULEPRIOMAP(Mandator
0 y)
SET
0 y)
SET
0 y)
SET
0 y)
BSC690
0 RMV USCPICH(Mandatory)
BSC690
0 SET USMLC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET USMLC(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
ADD USMLCCELL(Mandatory)
BSC690 MOD USMLCCELL(Mandatory)
0 RMV USMLCCELL(Mandatory)
ADD USMLCCELL(Mandatory)
BSC690 MOD USMLCCELL(Mandatory)
0 RMV USMLCCELL(Mandatory)
BSC690 ADD USMLCCELL(Mandatory)
0 MOD USMLCCELL(Mandatory)
BSC690 ADD USMLCCELL(Optional)
0 MOD USMLCCELL(Optional)




ADD USPG(Mandatory)
BSC690 MOD USPG(Mandatory)
0 RMV USPG(Mandatory)
BSC690 ADD USPG(Optional)

0 MOD USPG(Optional)




BSC690
0 SET USPIWEIGHT(Mandatory)
BSC690
0 SET USPIWEIGHT(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET USQICOUNT(Optional)
BSC690
0 SET USQICOUNT(Optional)
BSC690
0 SET USRNSR(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD USSCH(Mandatory)
0 RMV USSCH(Mandatory)
BSC690
0 ADD USSCH(Optional)
BSC690
0 ADD USSCH(Optional)
BSC690
0 SET USTATETIMER(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UTHPCLASS(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 RMV UTYPRAB(Mandatory)
ADD UTYPRABBASIC(Mandatory)
BSC690 MOD
0 UTYPRABBASIC(Mandatory)
BSC690
0 ADD UTYPRABBASIC(Mandatory)
BSC690
BSC690 ADD UTYPRABBASIC(Mandatory)

0 MOD UTYPRABBASIC(Optional)
BSC690



BSC690 ADD UTYPRABBASIC(Optional)

ADD
UTYPRABDCCCMC(Mandatory)
BSC690 MOD
0 UTYPRABDCCCMC(Mandatory)
ADD
BSC690 MOD
0 UTYPRABDCCCMC(Mandatory)
ADD
UTYPRABDCCCMC(Optional)
BSC690 MOD
0 UTYPRABDCCCMC(Optional)
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD
BSC690 MOD
ADD UTYPRABHSPA(Mandatory)
BSC690 MOD UTYPRABHSPA(Mandatory)
0 RMV UTYPRABHSPA(Mandatory)
ADD UTYPRABHSPA(Mandatory)
BSC690 MOD UTYPRABHSPA(Mandatory)
0 RMV UTYPRABHSPA(Mandatory)
BSC690 ADD UTYPRABHSPA(Optional)

0 MOD UTYPRABHSPA(Optional)
BSC690 ADD UTYPRABHSPA(Mandatory)

0 MOD UTYPRABHSPA(Mandatory)
BSC690 ADD UTYPRABHSPA(Mandatory)
BSC690 MOD
0 UTYPRABHSUPAPC(Mandatory)
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
0 UTYPRABHSUPAPC(Optional)
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 ADD UTYPRABOLPC(Mandatory)

0 MOD UTYPRABOLPC(Mandatory)


0 MOD UTYPRABOLPC(Optional)

ADD
UTYPRABQUALITYMEAS(Mandat
ory)
MOD
BSC690 UTYPRABQUALITYMEAS(Mandat
0 ory)
ADD
ory)
MOD
BSC690 UTYPRABQUALITYMEAS(Option
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD
ory)
MOD
0 al)
ADD UTYPRABRLC(Mandatory)
BSC690 MOD UTYPRABRLC(Mandatory)
0 RMV UTYPRABRLC(Mandatory)
BSC690 ADD UTYPRABRLC(Mandatory)
0 MOD UTYPRABRLC(Mandatory)

0 MOD UTYPRABRLC(Optional)


BSC690 ADD UTYPRABRLC(Optional)
















BSC690 MOD
0 UTYPSRBHSUPAPC(Mandatory)
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
0 UTYPSRBHSUPAPC(Optional)
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690 MOD
BSC690
0 MOD UTYPSRBRLC(Mandatory)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 MOD UTYPSRBRLC(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UU2LTEHONCOV(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
0 SET UUEA(Optional)
BSC690
0 SET UUESTATETRANS(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
SET
BSC690 UUESTATETRANSTIMER(Option
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
SET
0 al)
BSC690
0 SET UUIA(Optional)
UUNOFFLOADIP(Mandatory)
BSC690 RMV
0 UUNOFFLOADIP(Mandatory)
BSC690 RMV
BSC690 RMV
BSC690 ADD UURA(Mandatory)
0 RMV UURA(Mandatory)
BSC690
0 ADD UURA(Mandatory)
BSC690
0 SET UUSERGBR(Mandatory)
BSC690
BSC690
BSC690
BSC690
0 SET UUSERGBR(Optional)
BSC690
0 SET UUSERGBR(Optional)
BSC690 SET
0 UUSERHAPPYBR(Mandatory)
BSC690 SET
BSC690 SET
BSC690
0 SET UUSERHAPPYBR(Optional)
BSC690
0 SET UUSERMBR(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
SET
BSC690 UUSERPLNSHAREPARA(Optiona
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
SET
0 l)
BSC690
0 SET UUSERPRIORITY(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD UVIPIMSI(Mandatory)
0 RMV UVIPIMSI(Mandatory)
BSC690
0 SET UVIPTRACESW(Mandatory)
BSC690
0 SET UWPSALGO(Optional)
BSC690
0 SET UWPSALGO(Optional)
BSC690
0 SET VCLLOP(Mandatory)
BSC690
BSC690
0 SET VCLLOP(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD VLANID(Mandatory)
0 RMV VLANID(Mandatory)

BSC690
0 ADD VLANID(Mandatory)
BSC690
0 ADD VPCLCX(Mandatory)
BSC690
BSC690
BSC690
0 ADD VPCLCX(Optional)
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690
BSC690 ADD VPCLCX(Optional)
0 RMV VPCLCX(Mandatory)
This parameter defines the times of retransmission of paging messages. If the times of retransmission exceed the value of this
Uniquely identifies an adjacent node
ID of one AAL2 path between two AAL2 nodes. The PATHID of the same AAL2 path configured between two AAL2 nodes mu
Lower layer link type of bearing the Path.

UNI: see"ADD UNILNK";
IMA: see"ADD IMALNK";
FRAATM: see"ADD FRALNK";
NCOPT: see"LST OPT";
ATMLOGICPORT: see"ADD ATMLOGICPORT";
NULL: used when testing.
Subrack number of bearing the AAL2 path
Number of the slot bearing the AAL2 link
Number of the UNI link that carries the PATH. The field is valid only when the " bearer type " parameter is set to UNI. The bea
Number of the IMA group that carries the PATH. The field is valid only when the " bearer type " parameter is set to IMA. The b
Number of the FRA ATM link that carries the PATH. This field is valid only when the " bearer type " parameter is set to FRAAT
Number of the NCOPT port that carries the path. This field is valid only when the " bearer type " parameter is set to NCOPT.
ATM logic port No. bearing the PATH. This field is valid only when the " bearer type " parameter is set to ATM logic port. The b
port must be the leaf ATM logic port (the last level ATM logic port).
Whether to add the AAL2 path to the resource group
Resource group number of the PATH
VPI of the AAL2 path out RNC
VCI of the AAL2 path out RNC
TX traffic record index of the AAL2 Path on the out RNC port (ATM layer PVC traffic). The traffic index is configured in the ATM
RX traffic record index of the AAL2 Path on the out RNC port (ATM layer PVC traffic). The traffic index is configured in the ATM
The ownership of the AAL2 path is local or peer
TRM load threshold index. The TRM load threshold must be configured (see "ADD TRMLOADTH").
Timer_CU timer. The parameter affects the AAL2 transport efficiency and transport delay.
Service type of carried over the PATH. For R99, only the R99 service can be carried. For HSPA, only the HSPA service can b
ATM address of the destination node of the AAL2 route. The value is entered in the hexadecimal format, with the length rangin
ICD address). The ATM address starting with H'45 close to seven and half bytes of the H'45 must be in the BCD code (15-bit d
0x45000971500202001F0000000000000000000000. When the DSP is not all zero, it is E.164A. The ATM address is allocate
Route logical number
Whether to indicate that the " destination ATM node " is the same as the ATM node specified by the " adjacent node ID ".
AAL2 connection establishment request timer. This timer is started when an AAL2 signaling entity sends the peer node a requ
AAL2 connection establishment indication timer. This timer is started when an AAL2 signaling entity sends the service user an
This timer is started when an AAL2 signaling entity sends the peer node a request for releasing an AAL2 connection.
This timer is started when an AAL2 signaling entity sends the peer node an indication for releasing an AAL2 connection.
This timer is started when an AAL2 signaling entity sends the peer node a request for blocking an AAL2 path.
This timer is started when an AAL2 signaling entity sends the peer node a request for unblocking an AAL2 path.
This timer is started when an AAL2 signaling entity sends the peer node a request for resetting an AAL2 path.
This timer is started when an AAL2 signaling entity sends the peer node a request for modifying the bandwidth of an AAL2 pat
This timer is started when an AAL2 signaling entity sends the service user an indication for modifying the bandwidth of an AAL
Type of the adjacent node
Transport type of the adjacent node and interface type
Resource management mode. When the interface type is IUB, the value can be set to SHARE or EXCLUSIVE. When the inter
Operator index of the resource group
Gold user TRMMAP index used by the current adjacent node
Silver user TRMMAP index used by the current adjacent node

Bronze user TRMMAP index used by the current adjacent node
Activation factor table index
Gold user load EQ index used by the current adjacent node
Silver user load EQ index used by the current adjacent node
Bronze user load EQ index used by the current adjacent node
Name of the adjacent node
ID of the adjacent node to be added. The parameter is valid when Adjacent node type is set to IUB.
This parameter specifies whether the RNC is connected to a SGSN or a GGSN. This parameter is valid when the node type is
Transport type
This parameter is valid when the node type is set to IUR, IUCS, IUPS, or NNI_AAL2SWITCH.
Whether to indicate it is the root node when the transport type is ATM or ATM_IP
Whether to indicate it is the upper level adjacent node when "Is Root Node" is set to No.
Specifies the subrack number.
This parameter is valid when the node type is set to UNI_AAL2SWITCH. It is the slot number of the SAAL link of the AAL2 sig
SAAL link number of the XPU board. This number identifies an SAAL link uniquely.
Function set of the adjacent node supported by local RNC. When the parameter is set to CS1, it indicates that the local RNC is
CS2 protocol version is backward compatible with the CS1. By default, the parameter is set to CS2. When the peer is not com
Alarm ID
Alarm blink filter threshold. When the interval between the generation and clearance of an alarm is equal to or smaller than the
Assume that this threshold is not 0. When the accumulated number of alarm blink times exceeds the threshold, the alarm is re
Assume that this threshold is not 0. When the number of alarm blink times is smaller than the threshold, the alarm is reported.
Maximum rate of the accumulated alarm blink duration to the alarm blink measurement period. Assume this threshold is not 0.
period, see "SET ALMBLKSW".
Minimum rate of the accumulated alarm blink duration to the alarm blink measurement period. Assume this threshold is not 0.
period, see "SET ALMBLKSW".
Base Station Controller alarm blink filter switch
Switch controlling whether to perform statistics of Base Station Controller alarms
Measurement period of filtered Base Station Controller alarms

Maximum capacity for storing the alarm log
Maximum number of days for storing history alarms
Serial number of the alarm record.
Identifier of the alarm. This parameter uniquely identifies an alarm.
Alarm severity. One severities can be selected. By default, all severities are selected.
Alarm mask switch
Number of the subrack
Port No. of environment alarm
Operating state of the environment alarm port
Alarm ID
Port type of environment alarm
Alarm level for a digital port
Upper limit for triggering an alarm
Lower limit for triggering an alarm
Shield flag of the alarm
If this parameter is set to "ON", you must set "OMU automatic switchover interval". Otherwise, "OMU automatic switchover inte
Automatic switchover interval. This parameter needs to be set only when "OMU automatic switchover switch" is set to "ON". Th
This parameter specifies whether turn on automatic switchover automatically.
Indicates the slot number for running this command

Type of logical port
Board type
Logical port number
Bearer type of the logical port
Bearing slot No.
IMA group number of the logical port
UNI link number
Fractional ATM link number of the logical port
Optical interface number of the logical port
Upper number of the logical port
Backward bandwidth of the logical port
Backward bandwidth of the logical port
Resource management mode of logical port
Index of the operator
Logical port flow control switch
Flow control parameter index
TRM load threshold index
Logical port number
Traffic index
Service type of the ATM
Rate unit
Peak rate of the ATM traffic
Average rate of the ATM traffic
Minimum guarantee rate of the ATM traffic
Maximum burst size (MBS)
Tolerable delay jitter
Purpose description of the ATM traffic record
Number of the slot
Turn on or turn off the BFD protocol switch
Whether to report the alarm to the alarm box

Number of the slot
Classes of boards classified according to function modules
Whether to back up the data of the board
Type of the board
Type of the board
Logical function type of the board

OAM:Operation And Maintenance Process
UCP:All the UCP subsystems are configured as CPUS to act as the control plane processing subsystems for UMTS RNC
RUCP:Subsystem 0 of RUCP is configured as the MPU subsystem to act as the resource management subsystem. The other
UUP:UMTS RNC User plane Process
ATM:AEUa/ATM ATM over E1/T1/J1 interface,AOUa/ATM ATM over channelized Optical STM-1/OC-3 interface,AOUc/ATM A
IP:GOUc/IP IP over GE Optical interface,GOUa/IP IP over GE Optical interface,PEUa/IP IP over E1/T1/J1 interface,FG2c/IP I
Optical STM-1/OC-3 interface
SAU:Service Aware Uint
Whether to back up the data of the board
Number of the subrack where the MPU subsystem is located
Number of the slot where the MPU subsystem is located
Whether to support the FRA (E1/T1 frame relay interface board)

Work mode of the board ports.
Load sharing:The ports of the active board and the standby board work independently. Load sharing mode is supported only w
parameter.
Backup:The ports of the standby board are used only for backup.
Number of the cabinet
Power mode of the cabinet
Number of the cabinet
Customized command group to be processed.
You can select one or more commands.

Customized command group to be processed.
Name of the command group. You can define the name.
Name of the root certificate file
Name of the certificate file
Name of the private key file

Whether to enable the private key password.
DISABLE: indicating that the private key password is disabled.
ENABLE: indicating that the private key password is enabled.
Private key password

Whether to enable the certificate revocation list.
DISABLE: indicating that the certificate revocation list is disabled.
ENABLE: indicating that the certificate revocation list is enabled.
Name of the certificate revocation list file.

Whether to enable the certificate chain
DISABLE: indicating that the certificate chain is disabled
ENABLE: indicating that the certificate chain is enabled
Name of the certificate chain file
Identifies a maintenance domain
Specifies the identifier of a VLAN. Connectivity Fault Management (CFM) supports the creation of a Maintenance Association
Identifies a maintenance group. Maintenance group: maintenance alliance (MA), which is a component of the maintenance do
The range of the MA index is 0~99 for one pair of active and standby FG2a or GOUa boards, or 0~499 for one pair of active a
Name of the MA
Transmission period of the CCM packet in the MA
The subrack number for running this command

Identifies a maintenance domain
Class of the maintenance domain
name of the MD

Identifies a maintenance group. Maintenance group: maintenance alliance (MA), which is a component of the maintenance do
The range of the MA index is 0~99 for one pair of active and standby FG2a or GOUa boards, or 0~499 for one pair of active a
The type of the maintenance point added to the maintenance group. LocalMep indicates a local maintenance point and Remo
Identifies a maintenance point in the maintenance alliance
A maintenance point is an edge node of the MA.
Indicates the type of the physical port used by the local maintenance point in the maintenance group. FE indicates the FE port
Specifies Ethernet port number.
TRUNK group number
Type of the subrack
Number of the slot
Type of the board
Port for output LINE1. Only one clock source can be configured and this parameter specifies the clock source.(The actual valu
Whether to use Back-up port for LINE1
Back-up port for output LINE1. Only one clock source can be configured and this parameter specifies the clock source.(The ac
This parameter applies only to the Gb interface boards. When the clock sources of the SGSN and the MSC are different, set th
Switch of panel BITS1(2M)

Switch of panel BITS2(2M)
Switch of backplane LINE1
Switch of backplane LINE2

Working mode of the system clock. Working modes of the system clock are as follows: MANUAL: In this mode, you must spec
this mode, the crystal oscillator of board is used.
Priority of the clock source
Priority of the clock source.There are four priorities (in descending order): 1, 2, 3, 4.
Type of the clock source.
Type of the clock board
Configuration rollback control switch that is used to specify whether to support the configuration rollback function
Type of the connection between the NE and EMS or LMT. The connection can be a plain connection or SSL encryption conne
Board type
Port selection
Port number
E1/T1 port number
Byte length of J2
Byte display format of J2
Sending value of J2. The input string should be combined by characters whose ASCII values are defined from 0 to 127 in ASC
Expected receiving value of J2. The input string should be combined by characters whose ASCII values are defined from 0 to
A zero or a space used to fill in the J byte of the optical port based on the J byte of the peer equipment. If the J bytes are incon
Unique ID of a cell
This parameter defines the switch of Cell-Oriented service distribution and load balancing algorithm. If SERVICE-BASED is se
is selected, it will be automatically adjusted to SERVICE-BASED or LOAD-BASED according the load status of current cell.
This parameter defines the load difference threshold between 3G cell and 2G cell when CS service is distributed to 2G. If the l
This parameter defines the load difference threshold between 3G cell and 2G cell when PS service is distributed to 2G. If the l
CPU usage alarm clearance threshold. When the CPU usage is lower than the threshold, the CPU usage alarm is cleared. "CP
CPU usage alarm threshold. When the CPU usage exceeds the threshold, a CPU usage alarm is reported. "CPU occupancy a
DSP usage alarm clearance threshold. When the DSP usage is lower than the threshold, the DSP usage alarm is cleared. "DS
DSP usage alarm threshold. When the DSP usage exceeds the threshold, a DSP usage alarm is reported. "DSP occupancy a
Throughput usage alarm clearance threshold. When the throughput usage is lower than the threshold, the throughput usage a
Throughput usage alarm threshold. When the throughput usage exceeds the threshold, a throughput usage alarm is reported.
Upper layer application type, including CCP, NCP, ALCAP, and operation and maintenance link IPoAPVC
Activation factor. The bandwidth of this link is the bandwidth of the CCP, NCP, ALCAP, and IPoA PVC multiplied by the activa
Name of the file that backs up the OMU data.
Device IP Address Type
IP address of the board
Subnet mask of the board
Specifies the Maximum Transmission Unit size.
DHCP Relay ID
This parameter indicates the IP Address of DHCP Relay Gateway.
Differentiated service code is used to identify the service priority of the user.
VLAN priority
Board type
Port selection
E1/T1 port number

Whether support the balanced mode and unbalanced mode.
When this parameter is set to "YES", you can run MML commands to set the balancing mode of the interface boards. You do n
When this parameter is set to "NO", you must run MML commands to set the working mode to T1 if the working mode needs to
Working mode.
E1: The E1 system is recommended by the IUT-T. E1 carries signals at 2.048 Mbit/s. G.703 defines the electrical specification
T1: The T1 system is recommended by the ANSI and widely used in the North America. T1 carries signals at 1.544 Mbit/s.
E1_BA: A circuit that uses two wires to transmit the same but contra-directional signals. The 120-ohm E1 line and 100-ohm T1
E1_UNBA: A circuit that uses one transmission signal cable and one common grounding cable to transmit signals. The 75-ohm
Frame structure
Sending frame structure
Receiving frame structure
Line coding method
Scramble switch
This parameter specifies whether to use timeslot 16, or not.
Loop Detect Switch

Remark
Board type
E1/T1 port number
Loopback type
The loopback channel number for loopback mode of single channel local loop
The loopback channel number for loopback mode of single channel remote loop, it can select more than one channel
It specifies the loopback duration.
IP address of the NE management system

External virtual IP address of the OMU
Subnet mask of the OMU in the external network
48V voltage alarm switch
24V voltage alarm switch
Temperature alarm switch
Humidity alarm switch
Water sensor alarm switch
Smog alarm switch
Infrared alarm switch
Door status alarm switch
Sensor type of extended analog signal 1
Upper limit for triggering a 48V voltage sensor alarm
Lower limit for triggering a 48V voltage sensor alarm
Upper limit for triggering a 24 V voltage sensor alarm
Lower limit for triggering a 24 V voltage sensor alarm
Upper limit of temperature
Lower limit of temperature
Upper limit of humidity. When the humidity exceeds the upper limit, a humidity alarm is reported.
Lower limit of humidity. When the humidity is lower than the lower limit, a humidity alarm is reported.
Upper limit of extended output analog signal 1. If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of this para
Lower limit of extended output analog signal 1. If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of this param
Maximum measurement range of extended analog signal 1. If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit
Minimum measurement range of extended analog signal 1. If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit
Upper limit of extended output analog signal 2. If "Sensor Type of External Analog 2" is set to VOLTAGE, the unit of this param
Relay switch 1
Relay switch 2
Relay switch 3
Relay switch 4
Relay switch 5
Relay switch 6
New name of the alarm
Network management type of the alarm. By default, all network management types are selected.
IP address index of the Ethernet port
Local IP address of the Ethernet port
Subnet mask of the ether port
Board type
Ethernet port type
Whether the self-negotiation mode is adopted

1. When the FG2a/FG2c board is used and the port type is GE, the default of the local self-negotiation mode is adopted.
2. If the self-negotiation mode is adopted, the FE port rate, working mode and flow control mode must be in accordance with th
Otherwise, transmission failure must be incurred.
3. If the self-negotiation mode is adopted on the local system, the peer must use the self-negotiation mode.
Rate over the GE electrical port. When this parameter is set to 1000M, the GE electrical port performs negotiation at the rate o
Mbit/s or 1000 Mbit/s.
Specifies the Maximum Transmission Unit size.
This parameter specifies whether to send and process the flow control frame on the physical layer, or not. The setting of this p
Ratio of the minimum guarantee bandwidth of the OAM stream to the port bandwidth
Port flow control switch
Error-frame detect switch
Error-frame alarm threshold
Received broadcast packets alarm threshold. When a network storm occurs on the network, the quality of the services carried
second is greater than the specified alarm threshold for 30 consecutive seconds.
Received broadcast packets alarm clear threshold. It is automatically cleared when the number of broadcast packets received
CFM protocol version. Value V7 indicates that the 1AG protocol of draft 7 is used. Value V8 indicates that the 1AG protocol of
Slot number for running this command

Aggregation group number
Trunk group working mode.

Trunk group system priority.
Recovery mode of the Trunk group.
Aggregation mode. When this parameter is set to static aggregation, the LACP protocol is activated; otherwise, the LACP prot
Ratio of the minimum guarantee bandwidth of the OAM stream to the port bandwidth
CFM protocol version. Value V7 indicates that the 1AG protocol of draft 7 is used. Value V8 indicates that the 1AG protocol of
IP address index of the aggregation group
Local IP address of the aggregation group
Subnet mask
Slot number of the aggregation member
Port number of the aggregation member
Trunk group working mode.

Trunk port priority.
Interval between the fault analysis center starts and the fault analysis center beings to analyze faults.
Period of fault analysis.
Switch for controlling whether the detailed log of fault analysis is to be recorded. You are advised to turn the switch on during f
Type of the fan
Fan adjustment mode
Duty ratio-based speed adjustment
Number of CPU usage samples involved in the calculation of the average CPU usage in the sliding window
Number of CPU usage sampling times for fast judgment. The value of this parameter must be of half size of "Filter window" or
Critical threshold of CPU usage. When the CPU usage in "Fast judgement window" reaches or exceeds the threshold, all activ
Printing control threshold. If the CPU usage of sliding windows reaches or exceeds the threshold, printing flow control is trigge
Printing control threshold. If the CPU usage of sliding windows is lower than the threshold, printing flow control on the serial po
CPU usage threshold for debugging tracing flow control. When the average CPU usage of sliding windows reaches or exceed
CPU usage threshold for recovery from debugging tracing flow control. When the average CPU usage of smooth windows is lo
CPU usage threshold for performance monitoring. When the average CPU usage of sliding windows reaches or exceeds the t
CPU usage threshold for recovery from performance monitoring. When the average CPU usage of sliding windows is lower tha
CPU usage threshold for resource auditing control. When the average CPU usage of sliding windows reaches or exceeds the
CPU usage threshold for recovery from resource auditing control. When the average CPU usage of sliding windows is lower th
CPU usage threshold for paging flow control over the short message service (SMS). When the average CPU usage of sliding
CPU usage threshold for recovery from paging flow control over the short message service (SMS). When the average CPU us
CPU usage threshold for paging flow control over best effort (BE) services, supplementary services (SS), and location service
thresholds as SS and LCS to ensure the paging success rate of real-time services.
CPU usage threshold for stopping paging flow control over best effort (BE) services, supplementary services (SS), and locatio
control thresholds as SS and LCS to ensure the paging success rate of real-time services.
CPU usage threshold for paging control over real-time services. When the average CPU usage within the length of sliding win
CPU usage threshold for stopping paging control over real-time services. When the average CPU usage within the length of sl
services.
CPU usage threshold for handover control. When the average CPU usage of sliding windows reaches or exceeds the threshol
CPU usage threshold for recovery from handover control. When the average CPU usage of sliding windows is lower than the t
CPU usage threshold for Iur uplink flow control. When the average CPU usage of sliding windows reaches or exceeds the thre
CPU usage threshold for recovery from Iur uplink flow control. When the average CPU usage of sliding windows is lower than
CPU usage threshold for Iur downlink flow control. When the average CPU usage of sliding windows reaches or exceeds the t
CPU usage threshold for recovery from Iur downlink flow control. When the average CPU usage of sliding windows is lower th
CPU usage threshold for Cell Broadcast Service (CBS) flow control. When the average CPU usage of sliding windows reache
CPU usage threshold for recovery from CBS flow control. When the average CPU usage of sliding windows is lower than the t
CPU usage threshold for log flow control. When the average CPU usage of sliding windows reaches or exceeds the threshold,
CPU usage threshold for recovery from log flow control. When the average CPU usage of sliding windows is lower than the thr
CPU usage threshold for cell update. When the average CPU usage of sliding windows reaches or exceeds the threshold, cell
CPU usage threshold for recovery from cell update control. When the average CPU usage of sliding windows is lower than the
Load sharing threshold of the current XPU. When the CPU usage of an XPU exceeds the threshold, load sharing is configurab
Difference between CPU usage of the current and target XPUs. If the difference between CPU usage of the current and target
Access flow control threshold. When the average CPU usage of sliding windows exceeds the threshold, AC flow control is trigg
Access flow control recovery threshold. When the average CPU usage of sliding windows is lower than the threshold, AC flow
CPU usage threshold for Iur-g interface control. When the average CPU usage of sliding windows reaches or exceeds the thre
CPU usage threshold for recovery from Iur-g interface control. When the average CPU usage of sliding windows is lower than
CPU usage threshold for low priority service flow control. When the average CPU usage of sliding windows reaches or exceed
CPU usage threshold for recovery from flow control over low priority service. When the average CPU usage of sliding windows
CPU usage threshold for normal priority service flow control. When the average CPU usage of sliding windows reaches or exc
CPU usage threshold for recovery from flow control over normal priority service. When the average CPU usage of sliding wind
CPU usage threshold for high priority service flow control. When the average CPU usage of sliding windows reaches or excee
CPU usage threshold for recovery from flow control over high priority service. When the average CPU usage of sliding window
Access flow control threshold. When the average CPU usage of sliding windows exceeds the threshold, MR flow control is trig
Access flow control recovery threshold. When the average CPU usage of sliding windows is lower than the threshold, MR flow
Number of CPU usage samples involved in the calculation of the average CPU usage in the sliding window
Critical threshold of packet queue usage. When the packet queue usage reaches or exceeds the threshold, all active flow con
Printing control threshold. When the packet queue usage of sliding windows reaches or exceeds the threshold, printing flow co
Printing control threshold. When the packet queue usage of sliding windows is lower than the threshold, printing flow control o
Packet queue usage threshold for debugging tracing flow control. When the average packet queue usage of sliding windows r
Packet queue usage threshold for recovery from debugging tracing flow control. When the average packet queue usage of sm
Packet queue usage threshold for performance monitoring. When the average packet queue usage of sliding windows reache
Packet queue usage threshold for recovery from performance monitoring. When the packet queue usage of sliding windows is
Packet queue usage threshold for resource auditing control. When the average packet queue usage of sliding windows reache
Packet queue usage threshold for recovery from resource auditing control. When the average packet queue usage of sliding w
CPU usage threshold for paging flow control. When the average CPU usage of sliding windows reaches or exceeds the thresh
Packet queue usage threshold for recovery from paging flow control. When the average packet queue usage of sliding window
Packet queue usage threshold for handover control. When the average packet queue usage of sliding windows reaches or exc
Packet queue usage threshold for recovery from handover control. When the average packet queue usage of sliding windows
Packet queue usage threshold for Iur uplink flow control. When the average packet queue usage of sliding windows reaches o
Packet queue usage threshold for recovery from Iur uplink flow control. When the average packet queue usage of sliding wind
Packet queue usage threshold for Iur downlink flow control. When the average packet queue usage of sliding windows reache
Packet queue usage threshold for recovery from Iur downlink flow control. When the average packet queue usage of sliding w
Packet queue usage threshold for CBS flow control. When the average packet queue usage of sliding windows reaches or exc
Packet queue usage threshold for recovery from CBS flow control. When the average packet queue usage of sliding windows
Packet queue usage threshold for log flow control. When the average packet queue usage of sliding windows reaches or exce
Packet queue usage threshold for recovery from log flow control. When the average packet queue usage of smooth windows i
Packet queue usage threshold for cell update. When the average packet queue usage of sliding windows reaches or exceeds
Packet queue usage threshold for recovery from cell update control. When the average packet queue usage of sliding window
Access packet queue usage threshold. When the average packet queue usage of sliding windows exceeds the threshold, AC
Access packet recovery threshold. When the average packet queue usage of sliding windows is lower than the threshold, AC
Packet queue usage threshold for Iur-g interface. When the average packet queue usage of sliding windows reaches or excee
Packet queue usage threshold for recovery from Iur-g interface. When the average packet queue usage of sliding windows is l
Flow control switch. Other switches are valid only when "Flow control switch" is "ON".
Whether to control the printing flow on the serial port
Whether to control the debugging tracing flow
Whether to monitor the RRM performance
Whether to control the resource auditing flow
Whether to control paging flow
Whether to control handover flow
Whether to control the traffic on the Iur uplink
Whether to control the traffic on the Iur downlink
Whether to control CBS flow
Whether to control the log flow
Whether to control cell updates
Maximum traffic rate for restriction in the case of congestion on the IU interface. This parameter is valid only when "Board Clas
Whether to control AC flow
Whether to control signaling traffic on the IU interface

Whether to control traffic on the Iur-g interface
Whether to control MR flow
Link number of fractional ATM/IMA
Number of the bearing port
Bearer timeslot
Fractional link type
IMA group
Link flow control switch
Flow control parameter index. This parameter must be a flow control parameter that is already set through the "ADD PORTFLO
Operator Separated Flag.
Operator Separated Index.
Start data port on the FTP client.
End data port on the FTP client.
Password.
Confirm password. The confirm password is required to ensure that a correct password is entered.
Encryption mode supported when the NE serves as the FTP server.
AUTO: indicating that the FTP client selects the encryption mode.
PLAINTEXT: indicating that the plain text mode is used forcibly.
ENCRYPTED: indicating that the encrypted mode is used forcibly.
Whether the FTP client supports the state firewall
IP address of the FTP server to be visited by the FTP client
This port is provided by the FTP server to be visited by the FTP client.
Start data port on the FTP server in passive mode.
End data port on the FTP server in passive mode.

Encryption mode used when the NE serves as the FTP client
AUTO: indicating that the FTP client automatically selects the encryption mode
PLAINTEXT: indicating that the plain text mode is used forcibly.
ENCRYPTED: indicating that the encrypted mode is used forcibly.
Whether to use the customized port
DEFAULTPORT: indicating that the FTP server uses the default port 21 as a command port and port 20 as a data port to prov
CUSTOMPORT: indicating that the FTP server uses the customized port to provide FTP services
Number of the command listening port of the server. You should not use any port number occupied by other applications.
Number of the data port of the server in active mode. You should not use any port number occupied by other applications.
Global routing management switch. If this switch is turned on, the IP addresses in the controlled range cannot be in the same
GPS receiver ID
GPS receiver type. An GPS receiver can be installed on the local RNC, a Node B controlled by the local RNC, or a neighborin
ID of the RNC where a GPS receiver is installed
ID of the cell to which a GPS receiver belongs.
Period for reporting GPS data
Period for reporting differential GPS data
Format of the geographic coordinates. The values include "DEG" and "SEC".
Metric system. The values of this parameter include "MET" and "IMP".
Longitude of the GPS receiver antenna
Latitude of the GP receiver antenna
Height of the specified GSP receiver antenna
Longitude of the GPS receiver antenna
Latitude of the GPS receiver antenna
Height of the specified GSP receiver antenna
Period for reporting GPS data
Period for reporting differential GPS data
Source IP address of the packet for preventing the ICMP attack
Mask of the source IP network segment of the packet against the ICMP attack
Packet type against the ICMP attack
Board type
IMA group
Minimum links required for this IMA group in the activated state
IMA identifier
Frame length. A longer frame improves the transmission efficiency, but at the same time reduces the sensitivity to errors.
Maximum delay difference between links in the same IMA group
IMA protocol version
Expected DELAY depth
IMA link number

Indicates the carrying slot
IMA group
Type of self-healing of an interface board.

Type of the Iu interface board enabled with self-healing.
Type of the Iub interface board enabled with self-healing.
Whether an interface board of a specific type supports self-healing.
Rate of faulty cells on a stand-alone board for reset.
Number of faulty NodeBs on a stand-alone board for reset.
Rate of faulty cells on active/standby board ports for reset.
Number of NodeBs whose ports are faulty on active/standby boards for reset.
Number of exchange/establishment requests.
Number of requests for and establishments of data exchange from the SPU to an interface board.
Rate of SPU exchange request timeout and SPU exchange establishment failure.
Query period.
Number of queries.
Number of consecutive faults in the query period for a board to be reset.
Maximum number of consecutive faults in the query period. The ME is reloaded if this threshold is reached.
Maximum number of self-healings of an interface board in a day.
Switch for controlling whether the detailed log of fault analysis is to be recorded. You are advised to turn the switch on during f
Duration of summarizing the UOIP signaling plane loopback test results.
Rate of faulty cells of one port for ME reload.
Board type
This parameter specifies whether to check the number of invalid packets received and report alarm on an interface board. Wh
is cleared when the number of invalid packets received per second within 30 seconds on a board is lower than the alarm clear
When the number of invalid packets received per second within 30 seconds on an interface board exceeds this threshold, an i
When the number of invalid packets received per second within 30 seconds on an interface board is lower than this threshold,
When this parameter is set to "ON", an interface board learns only the response messages to the ARP requests sent by itself.
Board type
Type of logical port
Logical port number
Bearer type of the logical port
FE/GE port number
Upper number of the logical port
Trunk group number of the logical port
PPP link number
MLPPP group number.

Resource management mode. The logical port working in the SHARE mode can be shared by multiple carriers. The logical po
Index of the operator

Switch for adjusting the dynamical bandwidth of the logical port. If this switch is turned on, the system adjusts the dynamical b
the IPPM, see the description of the command "ACT IPPM".
Maximum bandwidth for dynamic adjustment at the logical port
Minimum bandwidth for dynamic adjustment at the logical port
Threshold of bandwidth change based on the load control algorithm. When the system detects that the change of the available
Bandwidth of the logical port
Maximum burst size (MBS)
Minimum guarantee bandwidth of the OAM stream
Speed reduction coefficient of the logical port. When detecting link congestion through IPPM, the system reduces the bandwid
Logical port speed increase step. When detecting the available bandwidth increase through IPPM, the system increases the b
Statistics period of the packet drop ratio. This parameter indicates the period for collecting the statistics information about the p
Bandwidth increase step adjustment period. This parameter indicates the period to increase the bandwidth of the logical port.
Maximum ratio of the estimated bottleneck bandwidth
Packet drop ratio threshold for speed reduction. When the packet drop ratio exceeds the value of this parameter, the rate of th
Delay statistics period. This parameter indicates the period to collect the statistics information about the link transmission dela
Bandwidth reduction delay threshold. This parameter is used to trigger the function of bandwidth reduction at the logical port w
Number of suspension periods after the bandwidth adjustment is performed based on the packet drop ratio. This parameter sp
control the rate of the bandwidth adjustment at the logical port.
Number of delay adjustment suspension periods. This parameter specifies the delay statistics periods in which the bandwidth
logical port.
Average delay increase filtering index. The actual value is 1/2^ LATUPK. The value of LATUPK should be bigger than the one
Average delay reduction filtering index. The actual value is 1/2^ LATUDK. The value of LATUDK should be smaller than the on

Speed reduction alarm report threshold. When the proportion of the current available bandwidth to the adjustable bandwidth is
bandwidth. The adjustable bandwidth can be obtained by subtracting the minimum bandwidth from the maximum bandwidth.
Speed reduction alarm recovery threshold. When the proportion of the current available bandwidth to the adjustable bandwidth
IP packet multiplexing type
Adjacent node identifier of this IP path
IP path ID,Identifying an IP path
This parameter specifies whether it is QOSPATH, or not.
PHB type of the IPMUX to be enabled
Maximum sub-frame length. This parameter indicates the maximum sub-frame length for multiplexing. If the length of a sub-fra
Maximum multiplexing frame length
This parameter specifies the maximum time that the system waits before sending the multiplexed data. This parameter is used
UDP multiplexing mode of the sending party. If the mode that does not support the function of compressing the RTP header in
party supports both the UDP MUX RTP header and the function of compressing the RTP header.
UDP multiplexing mode of the receiving party. The mode that does not support the function of compressing the RTP header in
party supports both the UDP MUX RTP header and the function of compressing the RTP header.
IP packet multiplex index
IP packet multiplexing type
Local IP address
Peer IP address
Bearer type
Bearing slot No.
IMA group number
UNI link number
Fractional ATM link number of the bearer network
NCOPT port number of the bearer network
ATM virtual port number of the bearer PVC
VPI value of the VCL of the bearer network
VCI value of the VCL of the bearer network
Sending traffic index
Receiving traffic index
IPoA PVC peer type
Uniquely identifies an IP path

Transport type of the adjacent node to which the path belongs
This parameter specifies the type of an IP path. It indicates the priority of the user plane data that is carried on the IP path. Th
BE data, AF data, and EF data are all of the non-QoS type. Different data can share the bandwidth of a QoS-type IP path. The
type of the physical port is PPP or MP, the non-QoS type IP path is configured as a high-priority path. When the physical port
actual priority of user plane data, however, is set through the "SET PHBMAP" command.
The local IP address must be the configured IP address (including the IP address and port address of the interface board).
The peer IP address should not be the same as the local address.
Subnet mask of the peer IP
Transmit bandwidth of IP path
Receive bandwidth of IP path

Carry Flag of IP path
IPLGCPORT: indicates that the IP Path is carried on the IP logic port;
RSCGRP: indicates that the IP Path is carried on the resource group;
NULL: indicates that the IP Path is carried on the physics port.
Number of the IP logical port that carries the IP path
Number of the IP logical port that carries the IP path
Resource group number of the PATH
TRM load threshold index. The TRM load threshold must be configured.
If the parameter is set to Disable, the added IP path is not configured with the VLAN ID. If the parameter is set to Enable, the a
VLANID of the IP address of the specified next hop
IP path check flag
Peer IP address to be checked. The input address (CHKIPADDR) must be the address (regardless of the network segment ad
Ping check period of IP Path
Number of ping check timeouts. The parameter indicates the number of timeout record failures.
Ping packet length. It is the total length of the Ping packet containing the IP header.
IP path check type
Adjacent node identifier of this IP path
IP path ID,Identifying an IP path

Detection index
Destination IP address
Subnet mask
IP address of the next hop
Route priority.
Purpose description of the route record
Subnet mask
Subnet mask
Detection index. The index is a unique value ranging from 0 to 511 if it is not specified.
Number of the slot
In the normal mode, if the board cannot be reset, no operation is performed. In the force mode, if the board cannot be reset, th
This is the data file for upgrading board. The data file names of different boards are different.
This is the description file for resetting the board. The reset file names of different boards are different.
The occur threshold of 20258 alarm,you can set it from 90% to 99%
The recover threshold of 20258 alarm,you can set it from 90% to 99%
Product application mode
Primary operator flag. YES indicates to activate the license of the primary operator, and NO indicates to activate the license of
Operator index
Number of Erlangs for voice services
Max throughput of PS
The total HSDPA traffic of all operators cannot exceed the HSDPA value in the license.
The total HSUPA traffic of all operators cannot exceed the HSUPA value in the license.
The total MBMS traffic of all operators cannot exceed the MBMS value in the license.
The setting values cannot exceed the hardware capacity value in the license.
The total Fast Dormancy Enhancement value of all operators cannot exceed the Fast Dormancy Enhancement value in the lic
The setting values cannot exceed the hardware capacity value in the license.
The total PS active users value of all operators cannot exceed the PS active users value in the license.
The total Push To Talk value of all operators cannot exceed the Push To Talk value in the license.
Function switch 1
Function switch 2
Function switch 3
Function switch 4
Function switch 5
Name of the specified file. The specified file under the \ftp\license directory of the active OMU workspace.
Grace Protection Period Switch determines whether to enter the grace protection period.
Path load EQ threshold table index
Remark
Load threshold of the primary path for Common channel traffic. When the load of the primary path is greater than the value of
secondary path.
Threshold of the ratio of the secondary path load to the primary path load for Common channel traffic. When the load of the pr
preferably admitted on the secondary path.
Load threshold of the primary path for IMS Signal traffic. When the load of the primary path is greater than the value of this pa
Threshold of the ratio of the secondary path load to the primary path load for IMS Signal traffic. When the load of the primary p
on the secondary path.
Load threshold of the primary path for Signal traffic. When the load of the primary path is greater than the value of this parame
Threshold of the ratio of the secondary path load to the primary path load for Signal traffic. When the load of the primary path
secondary path.
Load threshold of the primary path for AMR voice traffic. When the load of the primary path is greater than the value of this pa
Threshold of the ratio of the secondary path load to the primary path load for AMR voice traffic. When the load of the primary p
Load threshold of the primary path for R99 CS conversational traffic. When the load of the primary path is greater than the valu
admitted on the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for R99 CS conversational traffic. When the load of t
conversational traffic is preferably admitted on the secondary path.
Load threshold of the primary path for R99 CS streaming traffic. When the load of the primary path is greater than the value of
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for R99 CS streaming traffic. When the load of the p
is preferably admitted on the secondary path.
Load threshold of the primary path for R99 PS conversational traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for R99 PS conversational traffic. When the load of t
Load threshold of the primary path for R99 PS streaming traffic. When the load of the primary path is greater than the value of
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for R99 PS streaming traffic. When the load of the p
Load threshold of the primary path for R99 PS high interactive traffic. When the load of the primary path is greater than the val
Threshold of the ratio of the secondary path load to the primary path load for R99 PS high interactive traffic. When the load of
interactive traffic is preferably admitted on the secondary path.
Load threshold of the primary path for R99 PS mid interactive traffic. When the load of the primary path is greater than the valu
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for R99 PS mid interactive traffic. When the load of t
Load threshold of the primary path for R99 PS low interactive traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for R99 PS low interactive traffic. When the load of t
Load threshold of the primary path for R99 PS background traffic. When the load of the primary path is greater than the value
Threshold of the ratio of the secondary path load to the primary path load for R99 PS background traffic. When the load of the
traffic is preferably admitted on the secondary path.
Load threshold of the primary path for HSDPA Signal traffic. When the load of the primary path is greater than the value of this
secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSDPA Signal traffic. When the load of the prima
Load threshold of the primary path for HSDPA IMS Signal traffic. When the load of the primary path is greater than the value o
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSDPA IMS Signal traffic. When the load of the p
Load threshold of the primary path for HSDPA conversational traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSDPA conversational traffic. When the load of t
Load threshold of the primary path for HSDPA streaming traffic. When the load of the primary path is greater than the value of
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSDPA streaming traffic. When the load of the p
Load threshold of the primary path for HSDPA high interactive traffic. When the load of the primary path is greater than the val
Threshold of the ratio of the secondary path load to the primary path load for HSDPA high interactive traffic. When the load of
Load threshold of the primary path for HSDPA mid interactive traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSDPA mid interactive traffic. When the load of t
Load threshold of the primary path for HSDPA low interactive traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSDPA low interactive traffic. When the load of t
Load threshold of the primary path for HSDPA background traffic. When the load of the primary path is greater than the value
Threshold of the ratio of the secondary path load to the primary path load for HSDPA background traffic. When the load of the
Load threshold of the primary path for HSUPA Signal traffic. When the load of the primary path is greater than the value of this
secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSUPA Signal traffic. When the load of the prima
Load threshold of the primary path for HSUPA IMS Signal traffic. When the load of the primary path is greater than the value o
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSUPA IMS Signal traffic. When the load of the p
Load threshold of the primary path for HSUPA conversational traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSUPA conversational traffic. When the load of t
Load threshold of the primary path for HSUPA streaming traffic. When the load of the primary path is greater than the value of
the secondary path.
Threshold of the ratio of the secondary path load to the primary path load for HSUPA streaming traffic. When the load of the p
Load threshold of the primary path for HSUPA high interactive traffic. When the load of the primary path is greater than the val
Threshold of the ratio of the secondary path load to the primary path load for HSUPA high interactive traffic. When the load of
Load threshold of the primary path for HSUPA mid interactive traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSUPA mid interactive traffic. When the load of t
Load threshold of the primary path for HSUPA low interactive traffic. When the load of the primary path is greater than the valu
Threshold of the ratio of the secondary path load to the primary path load for HSUPA low interactive traffic. When the load of t
Load threshold of the primary path for HSUPA background traffic. When the load of the primary path is greater than the value
Threshold of the ratio of the secondary path load to the primary path load for HSUPA background traffic. When the load of the
Real time flux load threshold of the primary path for BE traffic. When the real time flux load of the primary path is greater than
Threshold of the ratio of the secondary path real time flux load to the primary path real time flux load for BE traffic. When the re
of this parameter, the BE traffic is preferably admitted on the secondary path.
Board start load control
Name of the OMU process.
Switch for recording flow logs.
Switch for recording messages sent between OMU processes.
By which the logs of messages sent between OMU processes are filtered.
ID of the task of filtering logs of messages sent between OMU processes.
Code of the command of filtering logs of messages sent between OMU processes.
When the operation time of the OMU exceeds the value specified by this parameter, some records are deleted from the opera
Maximum number of records allowed in the operation log
Type of the log
The destination entity number uniquely identifies a destination entity.
The local entity number uniquely identifies a local entity.
The DSP index uniquely identifies a DSP.

Type of the destination entity. For details, see RFC4666.
M3UA_ASP: suggested to use when there is a signaling transfer point (STP) between the local entity and the destination entit
M3UA_IPSP: suggested to use when there is no signaling transfer point (STP) between the local entity and the destination en
M3UA_SS7SP: suggested to use when the destination entity is a narrowband signaling point
M3UA_SP: represents all types of the destination entity
Routing context. The routing context identifies a specified route. If the routing context is to be configured, its value must be ne
The name of an M3UA destination entity must be unique.
The local entity number uniquely identifies a local entity.
Uniquely identifies an OSP

Type of the M3UA local entity. For details about the ASP and IPSP, see RFC4666.
M3UA_ASP: suggested to use when there is a signaling transfer point (STP) between the local entity and the destination entit
M3UA_IPSP: suggested to use when there is no signaling transfer point (STP) between the local entity and the destination en
Routing context. The routing context identifies a specified route. If the routing context is to be configured, its value must be ne
The name of an M3UA local entity must be unique.
Uniquely identifies a signaling link set
Signaling link mask corresponding to the M3UA link set. It is used for the M3UA link load sharing. It is valid only when the work
link is used for the load sharing, B0001 and B1000 indicate that up to two links are used for the load sharing. The additional lin
Traffic mode of the M3UA link set. At present, only the active/standby and load sharing mode is available.
If the M3UA links in the link set work in overriding mode, only one link in the link set works in the active mode, and all other link
take over as the active link.
If the M3UA links in the link set work in load-sharing mode, all the M3UA links in the link set work in active mode and carry traf
Working mode of the M3UA link set, including M3UA_ASP and M3UA_IPSP. For details about the ASP and IPSP, see the RF
Pending timer of the M3UA link set
Name of the M3UA link set. The name of the M3UA signalling link set must be unique.
ID of an M3UA link in the specified link set
Number of the slot where the XPU board is located

Subsystem number of CPUS
Specifies the SCTP link number for the XPU board. This number uniquely identifies an SCTP link.
Priority of the signaling link. 0 indicates the highest priority.
Initial bearing tag of the M3UA link. This parameter can be set to either active mode or standby mode. For details about the re
Name of the M3UA link.M3UA link names and M3UA links have a one-to-one correspondence.
Route priority. The highest priority is represented by 0.
The M3UA route and its name have a one-to-one relationship.
Type of the measurement result files.
The longest time for which the measurement result files can be saved. The measurement result files will be automatically dele
The maximum space the measurement result files can take. The measurement result files will be automatically deleted if the s

Board type
Logical function type
MLPPP group number.
Specifies MLPPP type.
This parameter specifies whether to use the device IP address as the local IP address, or not. If this parameter is set to YES,
Local IP address of the MLPPP group.
Borrowed device IP address.
Subnet mask of the MLPPP group in BSC.
Peer IP address of the MLPPP group.
MLPPP/MCPPP sequence header option.
Number of MCPPP priorities. This parameter is valid when the MLPPP group type is MCPPP. Value 4(8) indicates that there a
Specifies the size of an MLPPP fragment. The length of packets should be bigger or equal with the value defined by this param
This parameter specifies whether to compress the IP header of a MLPPP group, or not.
Compression flag of the PPP link protocol domain
This parameter specifies whether to compress the address and control fields, or not. If this parameter is set to ENABLE, both e
This parameter specifies whether to enable the PPP frame multiplexing function, or not.If this parameter is set to ENABLE, the
Maximum length of the PPP multiplexing frame
Maximum length of the PPP multiplexing frame

Frame timeout duration of the PPP multiplexing group
Type of validation protocol for the PPP or MLPPP link negotiation.
Validation mode upon PPP or MLPPP link negotiation.
Username to validate, for the PPP or MLPPP link negotiation.
Password to validate, upon PPP or MLPPP link negotiation.
E1T1 anti-error switch.
Error emit threshold.

Error clear threshold.
Number of MCPPP priorities. This parameter is valid when the MLPPP group type is MCPPP. Value 4(8) indicates that there a
Maximum PPPMUX sub-frame length. If the PPP frame length is larger than this value, the PPPMUX multiplexing is performed
met: wMuxMaxSfL<=( wMuxMfl-8 )/2
The value of this parameter cannot be less than the maximum PPPMUX sub-frame length (MUXMAXSFL). This parameter can
condition must be met: wMuxMaxSfL <= ( wMuxMfl-8 )/2
Maximum time waiting for multiplexing
Error emit threshold.

Error clear threshold.
Board type
MLPPP group number.
PPP link number
Number of the E1T1 port for bearing the PPP link
Bearer E1/T1 port timeslot of MLPPP link.
Duration of the PPP/MLPPP link restart timer.
Duration of the PPP/MLPPP link keep-alive timer.

CRC verification mode of MLPPP link.
Number of the slot
Number of the slot
Indicates the port number for running this command
Recovery mode of the MSP protection group
Wait to restore time
This parameter determines whether the last three bits of K2 indicates the single end and the dual end, or not. For details abou
This parameter specifies whether to report the Signal Degrade (SD) alarm. For details about this parameter, see ITU-T G.841
When this parameter is set to ENABLE, the SD alarm threshold parameter must be set. In this case, if the signal degradation e
alarm and does not initiate the MSP switchover.
SD alarm triggering threshold

This parameter specifies the priority of Signal Fail (SF) and Signal Degrade (SD). This parameter is used for determining whet
When the priority of SF and SD is set to high at both the local end and the peer end, the MSP protection switchover is perform
according to the low-priority SDSF procedure defined in ITU-T G.841 standards.
Note that the setting of this parameter must be consistent between the local end and the peer end. In addition, the local end a
Backup mode of the switch protection group
Number of the slot
Indicates the port number for running this command

Control command of the MSP switchover protection group
Uniquely identifies a signalling link set
This parameter specifies a signaling link mask, corresponding to an MTP3 link set. It is used for MTP3 link load sharing. Relat
indicate that up to two links are used for the load sharing. The additional links are not used for the load sharing. This value AN
Whether to verify the centralized signaling link in the case of the link establishment. ON: emergency verification, that is, the ve
be ensured. You are advised to use the normal verification. That is, the emergency verification switch is set to OFF.
Name of the signalling link set
ID of an MTP3 link in a specified link set
Number of the subrack where the XPU board is located
Priority of the signaling link. 0 indicates the highest priority.
Test code length of the signaling link. By default, the value is 10.
Test code for the MTP3 link. After the successful test, the link can be used for carrying signaling services. If the test fails, the M
Name of the MTP3 link

Route priority. The highest priority is represented by 0.
Name of an MTP3 route
When a normal changeover cannot be initiated, services will be changed over to an alternative link after this timer expires to a
This timer is a protection timer waiting for an extended changeover acknowledgement message (XCA) from the peer end after
When a normal changeback cannot be initiated, services will be changed back to a normal link only after this timer expires to a
This timer is a protection timer waiting for a changeback acknowledgement message (CBA) from the peer end after the first ch
This timer is a protection timer waiting for a changeback acknowledgement message (CBA) from the peer end after the secon
This timer is started when a transmission prohibited message (TFP) is sent. The TFP will not be sent any more during the runn
When the reception of a TFP causes unavailability of a route, this timer is started to regularly check whether the route is recov
This timer is a protection timer waiting for an uninhibit acknowledgement message (LUA) from the peer end after an uninhibit m
This timer is a protection timer waiting for a force uninhibit acknowledgement message (LUA) from the peer end after a force u
This timer is a protection timer waiting for an inhibition acknowledgement message (LIA) from the peer end after an inhibition m
This timer is started when a link fails to be started. The restart of the link is initiated after this timer expires.
After a local link is inhibited, this timer is started to regularly check the management states at both ends of the link.
After a remote link is inhibited, this timer is started to regularly check the management states at both ends of the link.
This timer is a protection timer waiting for a signalling link test acknowledgement message (SLTA) from the peer end after a si
This timer is used to send the signalling link test messages (SLTM) to the peer end regularly.
This timer is a protection timer waiting for an L2 response after a link setup request is sent to the L2.
The DSP must have been configured. The DSP name must be unique.

Data format of the specified signaling point.
When this parameter is set to "WNF", the SPC is expressed in the form of an integer number.
When this parameter is set to "DNF", the SPC is expressed in three segments. The number of bits included in each segment d
When the signaling point code bits parameter is set to "BIT14", the number of bits included in each segment is 3, 8, and 3.
Assume that the signaling point code bits parameter is set to "BIT14" and the SPC is expressed in three segments 5-7-2. You
1. Convert the value in each segment to a binary number and fill 0s into a segment if the number of bits included in that segme
is 111. As previously stated, when the signaling point code bits parameter is set to "BIT14", eight bits must be included in the s
2. Convert this binary number to a decimal number. The decimal form of this binary number is 10,298.
As an integer, the DSP code can be expressed by a decimal digit or a hexadecimal digit. If the DSP code is expressed by a he
DSP code expressed in the format of segments 8-8-8
DSP type.
IUCS: indicates the IU interface CS control plane and user plane signaling point.
IUPS: indicates the signaling point of the IU interface PS control signaling plane.
IUR: indicates the signaling point of the base station controller that is connected to the RNC.
IUCS_ALCAP: indicates the signaling point of the IU interface CS user signaling plane.
IUCS_RANAP: indicates the signaling point of the IU interface CS control plane.
STP: indicates the signaling transfer point.
AAL2SWITCH: indicates the ATM switch.
IUPC: indicates the signaling point of the IUPC interface.
Signaling route load sharing. In the value, the number of 1s (represented by n) determines the maximum number (2) of routes
the load sharing. The AND operation between this value and " signaling link mask " in the link set is equal to 0.
The DSP and OSP are in the associated mode or non associated mode.
Whether to enable the signaling point with the signaling transfer function
DSP bearer type.
MTP3: indicates that the lower layer bearer is the MTP3 used in ATM/TDM scenario;
M3UA: indicates that the lower layer bearer is the M3UA used in IP scenario;
MTP3_M3UA: indicates that the lower layer bearer is the MTP3 and M3UA used in ATM/TDM/IP scenario.
The type of the network that is preferentially used to carry the DSP.
MTP3_FIRST: indicates that the MTP3 is preferentially used to carry the DSP;
M3UA_FIRST: indicates that the M3UA is preferentially used to carry the DSP.
Identifies the DSP protocol type, including ITUT(International Telecommunication Union - Telecommunication Standardization
Shield type of the alarm. "ALL" indicates one shield type instead of all types.
Number of the subrack where the indicator alarm to be queried is generated.
Number of the slot where the alarm is generated, the number of the slot where the OMU board is positioned is not supported.
Number of the port where the alarm is generated, only the ports for data transmission are supported, such as E1/T1 port, chan
Number of the DSP where the alarm is generated.

Type of alarm selection.
Name of an office. This parameter consists of only letters, numerals, hyphens, or underlines, and must start with a letter or a n
Routing mask
Account of the operator.
Description of the operator account.
Password
Confirm password. The confirm password is required to ensure that a correct password is entered.
Group to which the operator belongs. This parameter is used to limit the right of the operator.
Number of the command group.
Whether to limit the operation date of the operator.
Start date. The input format is YYYY&MM&DD.
End date of the user operation. Input format: YYYY&MM&DD.
Whether to limit the operation time of the operator
Start time. The input format is HH&MM&SS.
End time of the user operation. The input format of this parameter is HH&MM&SS.
Whether to limit the operation weekday of the operator. If the weekday needs to be limited, see the description of "Week".
You can select multiple weekdays.
Password.
User group.
Whether to limit the operation time of the operator.
Whether to limit the operation weekday of the operator.
Name of the OSP
Network ID
Number of bits contained in the signaling point code
Data format of the specified signaling point.

When this parameter is set to "WNF", the SPC is expressed in the form of an integer number.
When this parameter is set to "DNF", the SPC is expressed in three segments. The number of bits included in each segment d
Assume that the signaling point code bits parameter is set to "BIT14" and the SPC is expressed in three segments 5-7-2. You
1. Convert the value in each segment to a binary number and fill 0s into a segment if the number of bits included in that segme
is 111. As previously stated, when the signaling point code bits parameter is set to "BIT14", eight bits must be included in the s
2. Convert this binary number to a decimal number. The decimal form of this binary number is 10,298.
As an integer, the OSP code can be expressed by a decimal digit or a hexadecimal digit. If the OSP code is expressed by a he
OSP code expressed in the form of segments 8-8-8
Whether to enable the restart function
Whether to lock all the non-default local accounts
The index of the parameters about operator separate information
For there are four operators at all, the parameter can be selected from one to four.
The transport type which can only be ATM or IP
The type of operator.
Set the index of 1st operator to configure the bandwidth ratio or TRMLOADTH for the operator.
The parameter is to set the percentage of bandwidth for the operator.
The load threshold for 1st operator to protect the port from congestion. If the bandwidth usage of the operator is too high, the i
Set the index of 2nd operator to configure the bandwidth ratio or TRMLOADTH for the operator.
The load threshold for 2nd operator to protect the port from congestion. If the bandwidth usage of the operator is too high, the
Set the index of 3rd operator to configure the bandwidth ratio or TRMLOADTH for the operator.
The load threshold for 3rd operator to protect the port from congestion. If the bandwidth usage of the operator is too high, the
Set the index of 4th operator to configure the bandwidth ratio or TRMLOADTH for the operator.
The load threshold for 4th operator to protect the port from congestion. If the bandwidth usage of the operator is too high, the i
Whether to enable the local user management function
Board type
Port selection
Port number
Scramble switch
Optical interface standard

Optical port tributary numbering method. This parameter indicates the sequence of tributaries in an SDH frame. If the sequenc
ALCATEL_MODE:(1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,3
HUAWEI_MODE:(1,4,7,10,13,16,19,22,25,28,31,34,37,40,43,46,49,52,55,58,61,2,5,8,11,14,17,20,23,26,29,32,35,38,41,44,4
LUCENT_MODE:(1,4,7,10,13,16,19,2,5,8,11,14,17,20,3,6,9,12,15,18,21,22,25,28,31,34,37,40,23,26,29,32,35,38,41,24,27,30
Optical interface type. Value UNI indicates that the interface is a user network interface. Value NNI indicates that the interface
J0 type
Sending type of J0
Sending value of J0. J0 byte, also called the trace byte of the regenerator section on the optical port (RTIM), is one of the optic
combined by characters whose ASCII values are defined from 0 to 127 in ASCII table, viz. capital letters or lowercase letters, n
Expected receiving type of J0
Expected receiving value of J0. J0 byte, also called the trace byte of the regenerator section on the optical port (RTIM), is one
capital letters or lowercase letters, numbers and underline and so on.
J1 type
Sending type of J1
sending value of J1. J1 byte, also called the trace byte of the high-order path on the optical port, is one of the optical port inter
whose ASCII values are defined from 0 to 127 in ASCII table, viz. capital letters or lowercase letters, numbers and underline a
Expected receiving type of J1
Expected receiving value of J1. J1 byte, also called the trace byte of the high-order path on the optical port, is one of the optic
letters or lowercase letters, numbers and underline and so on.
S1 sending value. It is a synchronization status byte used by the local end to examine the quality of the received clock signals
Threshold of B1 and B2 signal failure

Threshold of B1 and B2 signal degrade
Threshold of B3 signal failure
Threshold of B3 signal degrade
A zero or a space used to fill in the J byte of the optical port based on the J byte of the peer equipment. If the J bytes are incon
optical adaptation type between high-order path and multiplex section.

Indicates the port number for running this command.
OIUa: 0; AOUa/POUa: 0~1; UOIa(ATM)/UOIa(IP)/AOUc/POUc: 0~3; UOIc: 0~7
Loopback type
Operation type of the command.
Type of the board
Logical function type of the board

UCP:All the UCP subsystems are configured as CPUS to act as the control plane processing subsystems for UMTS RNC
RUCP:Subsystem 0 of RUCP is configured as the MPU subsystem to act as the resource management subsystem. The other
UUP:UMTS RNC User plane Process
ATM:AEUa/ATM ATM over E1/T1/J1 interface,AOUa/ATM ATM over channelized Optical STM-1/OC-3 interface,AOUc/ATM A
IP:GOUc/IP IP over GE Optical interface,GOUa/IP IP over GE Optical interface,PEUa/IP IP over E1/T1/J1 interface,FG2c/IP IP
Unchannelized Optical STM-1/OC-3 interface
Patch type
Number of the slot

Value of the per-hop behavior (PHB)
The DSCP is a field of the IP data packet. It is used to assign the differentiated service to the communication networks. The D
Port protocol type
This parameter applies to the FG2a, GOUa, and UOIa(IP) boards. For the boards working in ATM transmission mode, this par
If the duration for buffering the data in queue 0 is more than or equals to the value of this parameter, flow control is triggered. F
If the duration for buffering the data in queue 0 is less than or equals to the value of this parameter, flow control is canceled. F
If the duration for buffering the data in queue 0 is more than or equals to the value of this parameter, the subsequent packets a
If the duration for buffering the data in queue 3 is more than or equals to or equals to the value of this parameter, flow control i
If the duration for buffering the data in queue 5 is more than or equals to the value of this parameter, flow control is triggered.
If the duration for buffering the data in queue 5 is less than or equals to the value of this parameter, flow control is canceled.
Board type
Logical function type
PPP link number.
Number of the E1T1 port for bearing the PPP link

Bearer E1/T1 port timeslot of PPP link.
This parameter specifies whether to use the device IP address as the local IP address, or not. If this parameter is set to YES,
Local IP address of PPP link. The IP address of the PPP link on the BSC side.
Borrowed device IP address.
Subnet mask of the PPP link
Peer IP address of PPP link
This parameter specifies whether to compress the packet headers, or not.
Compression flag of the PPP link protocol domain

This parameter specifies whether to compress the address and control fields, or not. If this parameter is set to ENABLE, both e
Maximum PPPMUX sub-frame length. If the PPP frame length is larger than this value, the PPPMUX multiplexing is performed
met: wMuxMaxSfL <= ( wMuxMfl-8 )/2
The value of this parameter cannot be less than the maximum PPPMUX sub-frame length (MUXMAXSFL). This parameter can
condition must be met: wMuxMaxSfL <= ( wMuxMfl-8 )/2.
Type of validation protocol for the PPP or MLPPP link negotiation.
Validation mode upon PPP or MLPPP link negotiation.
Username to validate, for the PPP or MLPPP link negotiation.
Password to validate, upon PPP or MLPPP link negotiation.
Duration of the PPP/MLPPP link restart timer.
Duration of the PPP/MLPPP link keep-alive timer.

CRC verification mode of PPP link.

PPP/MPGRP link type
MLPPP group number.

PPP link number.
Loop type.
It specifies the test duration.
Minimum length of the user password.
Complexity of the password.
Maximum number of retries when the user logs in.
Duration of time after which the locked user is unlocked automatically.
Interval for resetting the counter when the user fails to log in.
Interval between the date when the password takes effect and the date when the password expires.
Password Warning Period
Maximum History Password Numbers.
Maximum allowable number of repeats of a single character in the password for logging in to the LMT. If a single character in t
Switch for prompting the user to change the password forcibly upon the first login to the LMT.

First alarm switch of power distribution monitoring board
Second alarm switch of power distribution monitoring board
Upper limit of input voltage 1
Lower limit of input voltage 1

Minimum DSCP of queue 0. The IP packets with DSCP in a relation that "Min DSCP of queue 0" <= DSCP <= 63 is added to q
Minimum DSCP of queue 1. The IP packets with DSCP in a relation that "Min DSCP of queue 1" <= DSCP < "Min DSCP of qu
Minimum guarantee bandwidth switch of the OAM stream
DSCP value of the OAM stream. The data of the OAM stream are not added to queues 0 to 5 for transmission. Instead, the da
Configuration mode
Rollback type
Name of the rollback point
Description of the rollback point

ID of a cell. For detailed information about this parameter, see 3GPP TS 25.401.
Correspondence between Access Classes (ACs) 0-9 and an ASC. For details, see 3GPP TS 25.331.
Correspondence between AC 10 and an ASC. For details, see 3GPP TS 25.331.
Slot number of the MPU Subsystem for the centralized management of the resources
Transport resource group number
Type of the transport resource group
Whether to indicate the first class transport resource group
Upper class transport resource group No. It is valid only when " Is First Class Transport Resource Group " is set to NO.
The parameter indicates whether the resource group is shared or is used by a specific telecom carrier.
Operator index of the resource group
Bandwidth mode
Transmit bandwidth
Receive bandwidth
Specifies the bandwidth occupied when the " transmission resource group type " is IP and the " bandwidth mode " is HALF_DU
TRM load threshold index. The TRM load threshold must be configured (see "ADD TRMLOADTH").
Bearer type of the SAAL link outgoing port
Number of the subrack bearing the SAAL link
Number of the slot bearing the SAAL link
Number of the bearer UNI link. The parameter is valid only when " bearer type " is set to UNI.
Number of the bearer IMA group. The parameter is valid only when " bearer type " is set to IMA.
Number of the bearer FRAATM(Fractional ATM) link. The parameter is valid only when " bearer type " is set to FRAATM.
Number of the NCOPT port that carries the SAAL link. The parameter is valid only when " bearer type " is set to NCOPT.
ATM logic port number of the bearer. The parameter is valid only when " bearer type " is set to ATMLOGICPORT.
VPI value of the SAAL out RNC
VCI value of the SAAL out RNC

TX traffic record index of the SAAL link
RX traffic record index of the SAAL link
Interface type of the SAAL link. The interface type of the Iub interface is UNI. The interface type of the Iu and Iur interface link
Management proving mode of the SAAL link. When Management proving status is set to MPS_NORMAL, the SAAL sends the
set to MPS_NEUTRAL, the SAAL does not send the verification packet according to the user and peer requirements in the init
A protection timer started after the BGN, END, RS, and ER message are sent. If it times out, the system resends messages.
Interval of sending the Poll messages. It indicates the period during which the peer end responds after receiving a message.
Interval of sending the Poll messages when no data is sent
No response timer
Timer of waiting for STAT response from the peer end
This parameter specifies the interval between the initial alignment failure and the next initial alignment.
This parameter specifies the period of time required by a specific SSCF to assign a link.
This parameter specifies the interval between two consecutive packets sent by the SSCF for verification at the link verification
Specifies the frequency through which ER can be sent. If the second ER message is received before the timeout of the timer,
Maximum allowed duration without credit
Maximum number of allowed retransmissions during the verification.
Maximum number of allowed retransmission upon the timeout of the connection control timer (CCTMR).
Maximum data count in the poll period. It indicates the count of data packets (SD) allowed to be transmitted between the interv
Maximum length of the list in the STAT PDU
Number of transmitted verification packets in the initial verification. See the ITU-T Q2110.
Receiving window size. It controls the transmit speed of the peer.
Length of the connection establishment timer. This timer is started when the SCCP initiates establishment of a connection. Th
Length of the inactive TX timer. This timer is started after a connection is established successfully. When this timer expires, a
Length of the inactive RX timer. This timer is started after a connection is established successfully. If a detection message is n
Length of the connection release timer. When the SCCP starts releasing a connection, this timer is started. When this timer ex
Length of the repeated connection release timer. When the connection release timer expires, this timer is started. When this ti
Length of the resource release timer. When the connection release timer expires, this timer is started. When this timer expires
Length of the guard timer. When a faulty SCCP is recovered, this timer is started. When this timer expires, all procedures will b
Length of the reset timer. When the SCCP initiates a reset request, this timer is started waiting for resource release. For detail
Length of the reassembly timer. This timer is used for connectionless data reassembly. If this timer expires, you can infer that
Length of the subsystem test timer. The subsystem test message will be sent when this timer expires. For details on this param
Length of the coordination timer. For details on this parameter, see the protocol ITU-T Q.714.
Length of the subsystem test ignorance timer. This timer is used to specify a delay between the authorized exit and the actual
Length of the timer for freezing the local reference number (LRN) after SCCP connectionless data segmentation. When user d
Length of the expedited acknowledgment (EA) timer. This timer is used to confirm expedited data of class 3 messages of the S
Length of the timer for freezing the local reference number (LRN) after SCCP connection release. After SCCP connection rele
Number of the scheduled task.
Name of the scheduled task.
Status of the scheduled task. This parameter determines whether to start the scheduled task.
Uniquely identifying a SCPICH in a cell.
TX power of the SCPICH in a cell.
SCTP link work mode. Server mode: RNC starts the listening and waits for the peer to send the SCTP-INIT message. Client m
Upper layer application type of the SCTP link. The upper layer application type of the Iub interface is NBAP. The upper layer a
The DSCP is a field of the IP data packet. It is used to assign the differentiated service to the communication networks. The D
Specifies the local port number of an SCTP link.

Identifies the first local IP address that communicates with the peer end. When it is set to 0, it is invalid. This IP address must
Identifies the second local IP address that communicates with the peer end. When it is set to 0, it is invalid. This IP address m
First destination IP address. The invalid value is 0.
Second destination IP address. The invalid value is 0.
Destination SCTP port number
Whether the SCTP is bound to a logical port. For details, see "ADD IPLOGICPORT".
Logical port slot No. bound by the SCTP. For details, see the parameter "Slot No." of the "ADD IPLOGICPORT".
Logical port No. bound by the SCTP. For details, see the parameter "Logic port No." of the "ADD IPLOGICPORT".
When the "RTOMAX" parameter is set to a fixed value, the larger the value is, the longer the check of the link is.
When the "RTOMIN" parameter is set to a fixed value, the larger the value is, the longer the check of the link is.
When the "RTOMIN" and "RTPMAX" parameters are set to fixed values, the larger the value is, the longer the check of the link
It is used to calculate the round-trip time of the protocol stack and the RTO value. The value must be smaller than "RTOBETA
It is used to calculate the round-trip time of the protocol stack and the RTO value. The value must be greater than "RTOALPH
SACK delay timer
Heartbeat interval when the SCTP server is idle
If the number of the association retransmissions exceeds this value, the parameter is deleted automatically. The value must be
If the number of the path retransmissions exceeds this value, the parameter is deleted automatically. The value must be small
Whether to perform checksum when sending message. In the current version, users' setting on this parameter does not take e
Whether to perform checksum when receiving message. In the current version, users' setting on this parameter does not take
Checksum arithmetic type. According to the RFC4960, the ALDER32 algorithm is not applicable to the SCTP checksum. The C
Maximum transport unit
VLANID flag of first local IP address
VLAN ID of first Local IP address
VLANID Flag of second Local IP address
VLAN ID of second Local IP address

The field indicates whether the cross-connect path is available. When the cross-path is available, a maximum of four IP paths
local IP address and the first peer IP address, and the IP path between the second local IP address and the second peer IP ad
IP address and the second peer IP address.
The field indicates whether the primary path can be switched back when it is available.
The association is smoothly switched over to the primary path after the number of heartbeat responses is received.
Whether to enable the data binding function
Heartbeat interval when the SCTP server is idle
If the number of the association retransmissions exceeds this value, the parameter is deleted automatically. The value must be
If the number of the path retransmissions exceeds this value, the parameter is deleted automatically. The value must be small
Number of the NBAP service listening port
Number of the M3UA service listening port
Number of the BBAP service listening port

Number of the slot.
This parameter needs to be set when the SCUa and SCUb boards are installed in the same subrack.
Number of the port
State of the panel port switch
Type of the board.
CPU usage threshold for SMS RRC load sharing. When the CPU usage reaches or exceeds the threshold, SMS RRC connec
CPU usage threshold for recovery from SMS RRC load sharing. When the CPU usage is lower than this threshold, SMS RRC
CPU usage threshold for call RRC connection load sharing. When the CPU usage reaches or exceeds the threshold, call RRC
CPU usage threshold for recovery from RRC connection load sharing. When the CPU usage is lower than the threshold, call R
CPU usage threshold for location RRC load sharing. When the CPU usage reaches or exceeds the threshold, location RRC co
CPU usage threshold for recovery from location RRC load sharing. When the CPU usage is lower than the threshold, location
Packet queue usage threshold for SMS RRC load sharing. When the packet queue usage reaches or exceeds this threshold,
Packet queue usage threshold for recovery from SMS RRC load sharing. When the packet queue usage is lower than this thre
Packet usage control threshold for call RRC connection load sharing. When the packet queue usage reaches or exceeds the t
Packet queue usage threshold for recovery from RRC connection load sharing. When the packet queue usage is lower than th
Packet control threshold for location RRC load sharing. When the packet queue usage reaches or exceeds the threshold, loca
Packet queue usage threshold for recovery from location RRC load sharing. When the packet queue usage is lower than the t
Switch for the OMU self-healing
Switch for the self-healing of the OMU processes
Switch for the self-healing of the OMU when the OMU process memory is overloaded.
Self-healing switch for the Ethernet adapter traffic monitoring.
Synchronization period of the SNTP client service
IP address of the server
Number of the port that provides the time information on the SNTP server
Set patch switch parameter1

SSL authentication mode of the peer certificate
Number of the scheduled subtask
Command string of the scheduled subtask. This command can be only a service command, and the system command cannot
Sequence number of the command string of the scheduled subtask.
Subnet Number in a BSC

Name of the subrack to be added
Whether to connect the power monitoring board
Type of SCU Board
Hardware type of the subrack
Number of the scheduled subtask
Status of the scheduled subtask to be added
Command string of the scheduled subtask. This command can be only a service command, and the system command cannot
Based on different requirements, you can set different time points for the scheduled task.
Seven time modes are available:
1. ONTIME: When this parameter is set to "ONTIME", the command is executed once only at the specified time point.
2. DAILY_T: When this parameter is set to "DAILY_T", the command is executed every day. You can also set up to five time
3. DAILY_C: When this parameter is set to "DAILY_C", the command is executed every day. You can set the start time and e
4. WEEKLY_T: When this parameter is set to "WEEKLY_T", the command is executed every week. You can set the day in w
5. WEEKLY_C: When this parameter is set to "WEEKLY_C", the command is executed every week. You can set the day in w
is one week and the default time interval is 30 minutes.
6. MONTHLY_T: When this parameter is set to "MONTHLY_T", the command is executed every month. You can set the day
7. MONTHLY_C: When this parameter is set to "MONTHLY_C", the command is executed every month. You can set the day
interval is one month and the default time interval is 30 minutes.
Date when the scheduled task is started
Date when the scheduled task is stopped

Interval for executing the scheduled subtask
The unit is determined according to the time mode.
1. If the time mode is set to "DAILY_T" or "DAILY_C", the unit is day.
2. If the time mode is set to "WEEKLY_T" or "WEEKLY_C", the unit is week.
3. If the time mode is set to "MONTHLY_T" or "MONTHLY_C", the unit is month.
Day in the month on which the command can be executed.
Day in the week on which the command can be executed.
If the time mode is set to "DAILY_T", "WEEKLY_T", or "MONTHLY_T", you should set this parameter. This parameter specifie
If the time mode is set to "DAILY_T", "WEEKLY_T", or "MONTHLY_T", you should set this parameter.
Time when the scheduled subtask is stopped. If the time mode is set to "DAILY_T", "WEEKLY_T", or "MONTHLY_T", you sho
Interval for executing the scheduled subtask. If the time mode is set to "DAILY_C", "WEEKLY_C", or "MONTHLY_C", you sho
When the time mode is set to "ONTIME", you should set this parameter.
Status of the scheduled subtask to be modified
Date when the scheduled task is started
Date when the scheduled task is stopped

Interval for executing the scheduled subtask
The unit is determined according to the time mode.
1. If the time mode is set to "DAILY_T" or "DAILY_C", the unit is day.
2. If the time mode is set to "WEEKLY_T" or "WEEKLY_C", the unit is week.
3. If the time mode is set to "MONTHLY_T" or "MONTHLY_C", the unit is month.
If the time mode is set to "DAILY_T", "WEEKLY_T", or "MONTHLY_T", you should set this parameter.
Time when the scheduled subtask is stopped. If the time mode is set to "DAILY_T", "WEEKLY_T", or "MONTHLY_T", you sho
Interval for executing the scheduled subtask. If the time mode is set to "DAILY_C", "WEEKLY_C", or "MONTHLY_C", you sho
When the time mode is set to "ONTIME", you should set this parameter.
Description of the Base Station Controller
Name of the Base Station Controller of Network Element
Contact way of the Base Station Controller supplier
Location of the Base Station Controller
Services provided by the Base Station Controller
TGW ID
This parameter indicates the address of the operation and maintenance console for TGW.
This parameter indicates the mask of the operation and maintenance console for TGW.
Subrack number of the RNC interface board interworking with TGW
Slot number of the RNC interface board interworking with TGW

Date
Time
Whether to enable SCTP fault diagnosis.
If this switch is turned on, the RNC automatically checks whether internal transmission is normal after the RNC detects an SCT
Whether to enable SAAL link loopback self-healing.
If this switch is turned on, the RNC automatically checks whether internal transmission is normal after it detects an SAAL link f
Whether to enable SCTP link loopback self-healing.
If this switch is turned on, the RNC automatically checks whether internal transmission is normal after it detects an SCTP link f
Whether to enable SAAL link automatic tracing.
If this switch is turned on, the RNC automatically starts SAAL link tracing after it detects an SAAL link fault and sends the traci
Whether to enable SCTP link automatic tracing.
If this switch is turned on, the RNC automatically starts SCTP link tracing after it detects an SCTP link fault and sends the trac
Whether to enable Connection Confirm/Connection Request (CC/CR) flow control. The SCCP periodically measures the numb
If this switch is turned on, the RNC starts flow control if the proportion of the connection setup responses to the connection set
Whether to enable Connection Refused (CREF) congestion flow control. If this switch is turned on, flow control is started autom
Whether to enhance the interface board performance.
If this switch is turned on, the Busy Hour Call Attempts (BHCA) of the GOUa and FG2a boards can be greatly increased.
Whether to enable interface board flow control.
If this switch is turned on, the RNC adjusts the traffic load on the interface board according to the CPU usage of the interface b
Whether to turn on the SCTP receive data flow control switch.
If this switch is turned on, the initial link setup packets received after the tenth initial link setup packet in each second are disca
Parameter 1 reserved for future use.


ID that uniquely identifies a tracing task within the system.
Activation factor table index
Remark
WCDMA AMR general common channel service downlink factor
WCDMA general common channel service uplink factor

WCDMA IMS signaling service downlink factor
WCDMA IMS signaling service uplink factor
WCDMA MBMS general common channel service downlink factor
WCDMA signaling service downlink factor
WCDMA signaling service uplink factor

WCDMA AMR voice service downlink factor
WCDMA AMR voice service uplink factor
WCDMA R99 CS conversational service downlink factor
WCDMA R99 CS conversational service uplink factor
WCDMA R99 CS streaming service downlink factor

WCDMA R99 CS streaming service uplink factor
WCDMA R99 PS conversational service downlink factor
WCDMA R99 PS conversational service uplink factor
WCDMA R99 PS streaming service downlink factor
WCDMA R99 PS streaming service uplink factor

WCDMA R99 PS interactive service downlink factor
WCDMA R99 PS interactive service uplink factor
WCDMA R99 PS background service downlink factor
WCDMA R99 PS background service uplink factor
WCDMA HSDPA signaling downlink factor

WCDMA HSDPA IMS signaling downlink factor
UMTS HSDPA voice service downlink factor
WCDMA HSDPA conversational service downlink factor
HSDPA streaming service downlink factor
WCDMA HSDPA interactive service downlink factor
WCDMA HSDPA background service downlink factor

WCDMA HSUPA signaling uplink factor
WCDMA HSUPA IMS signaling uplink factor
WCDMA HSUPA voice service uplink factor
WCDMA HSUPA conversational service uplink factor
WCDMA HSUPA streaming service uplink factor

WCDMA HSUPA interactive service uplink factor
WCDMA HSUPA background service uplink factor
WCDMA EFACH channel downlink factor
WCDMA EPCH channel downlink factor
WCDMA ERACH channel uplink factor
TRM load threshold index. It is the unique ID of the load threshold.

Transport type
Load balance threshold type. It indicates the threshold calculation mode.
Reserved forward bandwidth for handover user
Reserved backward bandwidth for handover user
If the available forward bandwidth is less than or equal to this value, the forward congestion alarm is emitted and forward cong
If the available backward bandwidth is less than or equal to this value, the backward congestion alarm is emitted and backwar
If the available forward bandwidth is greater than this value, the forward congestion alarm is cleared and forward congestion c
If the available backward bandwidth is greater than this value, the backward congestion alarm is cleared and backward conge
If the available forward bandwidth is less than or equal to this value, the forward overload congestion alarm is emitted and forw
If the available backward bandwidth is less than or equal to this value, the backward overload congestion alarm is emitted and
If the available forward bandwidth is greater than this value, the forward overload congestion alarm is cleared and forward ove
If the available backward bandwidth is greater than this value, the backward overload congestion alarm is cleared and backwa
Ratio of reserved forward bandwidth for handover user
Ratio of reserved backward bandwidth for handover user
If the ratio of available forward bandwidth is less than or equal to this value, the forward congestion alarm is emitted and forwa
If the ratio of available backward bandwidth is less than or equal to this value, the backward congestion alarm is emitted and b
If the ratio of available forward bandwidth is greater than this value, the forward congestion alarm is cleared and forward conge
If the ratio of available backward bandwidth is greater than this value, the backward congestion alarm is cleared and backward
If the ratio of available forward bandwidth is less than or equal to this value, the forward overload congestion alarm is emitted a
If the ratio of available backward bandwidth is less than or equal to this value, the backward overload congestion alarm is emit
If the ratio of available forward bandwidth is greater than this value, the forward overload congestion alarm is cleared and forw
If the ratio of available backward bandwidth is greater than this value, the backward overload congestion alarm is cleared and
TRMMAP index
Remark
Transport type
Primary path that carries the common channel services
Secondary path that carries the common channel services
IMS SRB primary path

IMS signaling service bearer secondary path
Signaling service bearer primary path
Signaling service bearer secondary path
AMR voice service bearer primary path
AMR voice service bearer secondary path

R99 CS conversational service primary path
R99 CS conversational service secondary path
R99 CS streaming service bearer primary path
R99 CS streaming service bearer secondary path
R99 PS conversational service primary path

R99 PS conversational service secondary path
R99 PS streaming service bearer primary path
R99 PS streaming service bearer secondary path
R99 PS high PRI interactive primary path
R99 PS high PRI interactive secondary path

R99 PS middle PRI interactive primary path
R99 PS middle PRI interactive secondary path
R99 PS low PRI interactive primary path
R99 PS low PRI interactive secondary path
R99 PS background service bearer primary path

R99 PS background service bearer secondary path
HSDPA signaling bearer primary path
HSDPA signaling bearer secondary path
HSDPA IMS signaling bearer primary path
HSDPA IMS signaling bearer secondary path

HSDPA voice service bearer primary path
HSDPA voice service bearer secondary path
HSDPA conversational service bearer primary path
HSDPA conversational service bearer secondary path
HSDPA streaming service bearer primary path

HSDPA streaming service bearer secondary path
HSDPA high PRI interactive primary path
HSDPA high PRI interactive secondary path
HSDPA middle PRI interactive primary path
HSDPA middle PRI interactive secondary path

HSDPA low PRI interactive primary path
HSDPA low PRI interactive secondary path
HSDPA background service bearer primary path
HSDPA background service bearer secondary path
HSUPA signaling bearer primary path

HSUPA signaling bearer secondary path
HSUPA IMS signaling bearer primary path
HSUPA IMS signaling bearer secondary path
HSUPA voice service bearer primary path
HSUPA voice service bearer secondary path

HSUPA conversational service primary path
HSUPA conversational service secondary path
HSUPA streaming service bearer primary path
HSUPA streaming service bearer secondary path
HSUPA high PRI interactive primary path

HSUPA high PRI interactive secondary path
HSUPA middle PRI interactive primary path
HSUPA middle PRI interactive secondary path
HSUPA low PRI interactive primary path
HSUPA low PRI interactive secondary path

HSUPA background service bearer primary path
HSUPA background service bearer secondary path
Source of timeslot cross
Source timeslot mask
Destination of the timeslot cross connection
Target timeslot mask
Timeslot cross index

Time zone
Whether daylight saving time has to be used
Type of the start date. "WEEK" indicates that the start date is a weekday. "DATE" indicates that the start date is a month day.
Month in which DST starts

Start date of the daylight saving time (DST)
Sequence of the start week of DST
Weekday on which DST starts
Time to start DST. Note that the time set in this parameter is not a DST.
Type of the end date. "WEEK" indicates that the end date is a weekday. "DATE" indicates that the end date is a month day. "D
Month on which DST ends

End date of the daylight saving time
Sequence of the end week of DST
Weekday on which DST ends
Time to stop DST. Note that the time set in this parameter is a DST.
Offset to DST, namely, the adjustment to time.
ID of an RNC
Uniquely identifying a WCDMA cell, to which neighboring GSM cells can be added.
Unique ID of a GSM cell

Cell individual offset for the GSM cell.
This parameter is used for decision making for the inter-RAT handover. A larger value of the parameter indicates the higher th
Offset between the neighboring GSM cell and WCDMA cell.

This specifies the offset of the measurement value of the neighboring GSM cell signal quality. This parameter is used for RSS
In cell reselection algorithm, this parameter is used for moving the border of a cell. Content: During cell selection or resection,
parameter can be configured by the network planner according to reality.
For details, refer to 3GPP TS 25.331.
As for the impact on network performance:
The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller the value the param
Minimum RX level of the GSM cell.
Before the UE camps on the cell, take the measurement of the signal quality in the cell. If the quality is better than this parame
Specifies the penalty time for cell reselection.
If this parameter is set to a greater value, the penalty time for HCS cell reselection is prolonged. If this parameter is set to a sm
hierarchical cell structure cannot be deployed effectively.
Cell offset used for CPICH RSCP measurement value in HCS cell selection.
If this parameter is set to a greater value, the probability for selecting a neighboring cell reduces. If this parameter is set to a sm
Whether to perform blind handover.

The value FALSE indicates that the cell is not considered as a candidate cell for blind handover. Therefore, blind over to this c
Priority of the neighboring cell for blind handover.

The value 0 represents the highest priority. Priorities 0 to 15 are assigned to concentric neighboring cells, which can ensure su
DRD Ec/No threshold for determining whether to perform the blind handover. The DRD is permitted if Ec/No of the current cell
Indicates whether to send the system information block 11 (SIB11) including neighboring cell information.
The value "FALSE" indicates that the neighboring information is not included in the SIB11. The value "TRUE" indicates that th
Indicates whether to send the SIB12 indication including the neighboring cell information.
Priority flag of neighboring cells

The value TRUE indicates that the neighboring cell priority is valid, and the value FALSE indicates that the neighboring cell pri
Priority of neighboring cells.

A smaller value of this parameter indicates a higher priority assigned to the neighboring cell. The neighboring cell with a highe
This parameter is valid when "NPrioFlag" is set to TRUE.
Whether the cell supports the measure-based directed retry (MBDR) algorithm.
The value TRUE indicates that the cell supports the MBDR algorithm, and the value FALSE indicates that the cell does not su
Priority of a MBDR cell.
This parameter is valid only when the "MBDRFlag" parameter is set to TRUE. It indicates the tiptop priority when the value is s
when there are many of cells meet the quality condition. Attention, when there does not have cell meet the quality condition ba
This parameter specifies whether a neighboring 2G cell supports SRVCC.
When this parameter is set to "Without DTM", it indicates that the neighboring 2G cell does not support SRVCC in DTM mode.
When this parameter is set to "With DTM", it indicates that the neighboring 2G cell supports SRVCC in DTM mode. That is, SR
When this parameter is set to "OFF", it indicates that the neighboring 2G cell does not support SRVCC.
OFF indicates that the AC algorithm is automatically disabled. ON indicates that the AC algorithm is automatically enabled.
Access restriction ratio. When a cell performs access classes restriction, you can select some access classes from AC0 to AC
restriction is released and other access classes of the local cell are selected for access classes restriction based on the ratio s
Interval of automatic access classes restriction between cells. When a subsystem of an RNC performs access classes restricti
The process lasts until all the cells are going through access classes restriction. For detailed information of this parameter, ref
Interval of access classes restriction. When a cell performs access classes restriction, it selects some access classes and afte
When the Iu interface is faulty, the RNC gradually restricts cell access in Bar mode. When the Iu interface is restored, the RNC
time period and the risk due to congestion is reduced.
The activity factor at the radio layer varies with the service priority. The configuration of the activity factor is performed based o
UL activity factor of SRB.Signals might be discontinuously transmitted because of the activation detection of conversational se
DL.
DL activity factor of SRB. Signals might be discontinuously transmitted because of the activation detection of conversational se
DL.
UL activity factor of the R99 AMR conversational service. Signals might be discontinuously transmitted because of the activati
channel might be different in UL and DL.
DL activity factor of the R99 AMR conversational service. Signals might be discontinuously transmitted because of the activati
UL activity factor of the R99 non AMR conversational service. Signals might be discontinuously transmitted because of the act
DL activity factor of the R99 non AMR conversational service. Signals might be discontinuously transmitted because of the act
UL activity factor of the R99 streaming service. Signals might be discontinuously transmitted because of the activation detectio
be different in UL and DL.
DL activity factor of the R99 streaming service. Signals might be discontinuously transmitted because of the activation detectio
UL activity factor of the R99 interactive service. Signals might be discontinuously transmitted because of the activation detectio
DL activity factor of the R99 interactive service. Signals might be discontinuously transmitted because of the activation detectio
UL activity factor of the R99 background service. Signals might be discontinuously transmitted because of the activation detec
DL activity factor of the R99 background service. Signals might be discontinuously transmitted because of the activation detec
Activity factor of the MBMS service. Signals might be discontinuously transmitted because of the activation detection of conve
in UL and DL.
UL activity factor of the HSUPA conversational service. Signals might be discontinuously transmitted because of the activation
might be different in UL and DL.
DL activity factor of the HSUPA conversational service. Signals might be discontinuously transmitted because of the activation
UL activity factor of the HSUPA streaming service. Signals might be discontinuously transmitted because of the activation dete
DL activity factor of the HSUPA streaming service. Signals might be discontinuously transmitted because of the activation dete
UL activity factor of the HSUPA interactive service. Signals might be discontinuously transmitted because of the activation det
DL activity factor of the HSUPA interactive service. Signals might be discontinuously transmitted because of the activation det
UL activity factor of the HSUPA background service. Signals might be discontinuously transmitted because of the activation de
DL activity factor of the HSUPA background service. Signals might be discontinuously transmitted because of the activation de
Uniquely identifying a PRACH in a cell corresponding to the AICH
Uniquely identifying an AICH in a cell

This parameter specifies the transmission timing information of an AICH relative to uplink PRACH.
"0" indicates that there are 7680 chips offset between the access preamble of the PRACH and AICH. "1" indicates that there a
This parameter indicates whether the SCCPCH shall use STTD or not. For detailed information of this parameter, refer to 3GP
Difference between the transmit power of an AICH and that of PCPICH
The average CPU usage threshold for generating a resource overload alarm on the user plane.
The average CPU usage threshold for clearing a resource overload alarm on the user plane.
The average Guaranteed Bit Rate (GBR) usage threshold for generating a resource overload alarm on the user plane.
The average Guaranteed Bit Rate (GBR) usage threshold for clearing a resource overload alarm on the user plane.
Threshold E1 of DL AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value calculate
maximum DL TX power minus the relative threshold.
Threshold E2 of DL AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value calculate
Threshold F1 of DL AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value calculate
Threshold F2 of DL AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value calculate
To adjust the UL AMR speech rate, AMRC delivers the TFC CONTROL command and starts this timer. If no failure message i
The AMRC needs to check whether the TFO/TrFO exists before adjusting DL AMR speech rate. If the TFO/TrFO does not exi
peer RNC a command requesting the AMR mode at a lower level. In addition, the local RNC starts the timer. After the peer RN
adjustment of the DL AMR speech rate is successful. Otherwise, the adjustment fails.
Maximum rate of the narrowband AMR speech service for gold users.
Maximum rate of the narrowband AMR speech service for silver users
Maximum rate of the narrowband AMR speech service for copper users.
Threshold E1 of DL wideband AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value
threshold is equal to the maximum DL TX power minus the relative threshold.
Threshold E2 of DL wideband AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value
Threshold F1 of DL wideband AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value
Threshold F2 of DL wideband AMR speech rate adjustment. Periodical reporting is used for DL measurement. When the value
To adjust the UL wideband AMR speech rate, AMRC delivers the TFC CONTROL command and starts this timer. If no failure
The AMRC needs to check whether the TFO/TrFO exists before adjusting DL wideband AMR speech rate. If the TFO/TrFO do
delivers to the peer RNC a command requesting the wideband AMR mode at a lower level. In addition, the local RNC starts th
received before the timer expires, the adjustment of the DL wideband AMR speech rate is successful. Otherwise, the adjustme
Maximum rate of the wideband AMR speech service for gold users
Maximum rate of the wideband AMR speech service for silver users
Maximum rate of the wideband AMR speech service for copper users
No. of the subrack.
No. of the slot of the board.
This parameter specifies whether to activate the algorithm for detecting missing intra-frequency neighboring cells.
This parameter specifies whether to activate the algorithm for detecting missing inter-frequency neighboring cells.
This parameter specifies the number of measurement object. One measurement object contains parameters including downlin
Indicating the selected frequency Band in the cell setup process. For detailed information of this parameter, refer to 3GPP TS
This parameter specifies the downlink UARFCN of the frequency to undergo detection of missing inter-frequency neighboring
Note: The list of missing neighboring cells is a list of neighboring cells that are missing from the list of existing neighboring cell
neighboring cells. They are not counted in the existing neighboring cell relationship.
This parameter specifies the start scrambling code for detection of the frequency and defines the scrambling code range toget
This parameter specifies the end scrambling code for detection of the frequency and defines the scrambling code range togeth
This parameter specifies whether to activate the algorithm for detecting missing inter-RAT neighboring cells.
This parameter specifies the start Network Color Code (NCC) and defines the NCC range together with the end NCC. The NC
This parameter specifies the end NCC and defines the NCC range together with the start NCC. The NCC range, BCC range, a
This parameter specifies the start BCC and defines the BCC range together with the end BCC. The BCC range, NCC range, a
This parameter specifies the end BCC and defines the BCC range together with the start BCC. The BCC range, NCC range, a
This parameter specifies the band of the inter-RAT neighboring cells to be tested for detecting missing configuration of neighb
This parameter specifies the start ARFCN and defines the frequency range together with the end ARFCN. The frequency rang
This parameter specifies the end ARFCN and defines the frequency range together with the start ARFCN. The frequency rang
Uniquely identifying a BCH in a cell
Offset of the BCH transmit power from the PCPICH transmit power in a cell. For detailed information of this parameter, refer to
The parameter values are described as follows:
NODEB_CREDIT_CAC_SWITCH: The system performs CAC based on the usage state of NodeB credit. When the NodeB's c
Reserved Parameter1.
Reserved parameter 2.
The parameter specifies whether to perform Call Attempt Per Second (CAPS) control for the number of RRC connection estab
SYS_LEVEL indicates that the RNC will perform flow control for the RRC connection requests at SPU subsystem level.
NODEB_LEVEL indicates that the RNC will perform flow control for the RRC connection requests at NodeB level.
CELL_LEVEL indicates that the RNC will perform flow control for the RRC connection requests at cell level.
The parameter specifies whether to set up RRC connection for registration on the FACH instead of on the DCH in the call sho
When ON is selected, RNC will perform flow control at cell level or NodeB level, the RRC connection for registration is set up o
When OFF is selected, the channel setup strategy of RRC connection request for registration can be set by running the SET U
The parameter specifies the period of entering flow control at SPU subsystem level, NodeB level, or cell level.
In the period, if the number of RRC connection requests that the SPU subsystem, NodeB, or cell receives exceed relative trigg
The parameter specifies the threshold of entering flow control for RRC connection requests at SPU subsystem level.
During the call shock judgment period (CallShockJudgePeriod), when the number of RRC connection requests exceed the val
The flow control strategies for RRC connection requests are as follows:
If the originating interactive call, originating background call, or originating streaming call causes the RRC connection requests
If the number of admitted RRC connection requests for registration and inter-RAT cell reselection exceeds the value of "SysHi
If the number of admitted RRC connection requests for AMR exceeds the value of "SysAmrRrcNum", RNC will perform flow co
If other services cause RRC connection requests, RNC will not perform flow control.
The parameter specifies the number of RRC connection requests per second for originating conversational call at SPU subsys
The parameter specifies the number of RRC connection requests per second for registration and inter-RAT cell reselection at
The parameter specifies the maximum number of RRC Connection Reject messages per second from SPU subsystem to UE.
discard the RRC connection request.
The parameter specifies the threshold of entering flow control for RRC connection requests at NodeB level.
If the number of admitted RRC connection requests for registration and inter-RAT cell reselection exceeds the value of "NBHig
If the number of admitted RRC connection requests for AMR exceeds the value of "NBAmrRrcNum", RNC will perform flow co
The parameter specifies the number of RRC connection requests per second for originating conversational call at NodeB leve
The parameter specifies the threshold of entering flow control for RRC connection requests at cell level.
If the number of admitted RRC connection requests for registration and inter-RAT cell reselection exceeds the value of "CellHi
If the number of admitted RRC connection requests for AMR exceeds the value of "CellAmrRrcNum", RNC will perform flow co
The parameter specifies the number of RRC connection requests per second for originating conversational call at cell level.
Method of determining an HSDPA service rate when the differentiated HSPA service based on SPI weight function is enabled.
smaller one between MBR and the peak rate corresponding to the UE HSDPA category is used. Value Max indicates that the
Downlink rate threshold 1. This parameter is used to determine the value range of an HSDPA service rate when the differentia
Method of determining an HSUPA service rate when the differentiated service based on SPI weight function is enabled. Value
one between MBR and the peak rate corresponding to the UE HSUPA category is used. Value Max indicates that the greater
Uplink rate threshold 1. This parameter is used to determine the value range of an HSUPA service rate when the differentiated
Number of the EPS subrack managing the subsystem to which the NodeB belongs
UMTS XPU board slot Number
Represent an index for a CN operator.
IP address of the RNC
IP address of the CBC (Cell Broadcast Center)
Mask of the sub-network of the CBC IP address

ID of a CBS area.
Type of a CBS area.
Code of a location area, where the MS can move without location update. Proper division of location area facilitates load balan
ID of a cell. For details on this parameter, see 3GPP TS 25.401.

the only identifier of the simple cell broadcast
Represent an index for a CBS message.

Channel ID for a CBS message.
Geographical coverage of a CBS message. A normal CBS message can be transmitted by cell, PLMN, or SA, and an emerge
Priority for sending simplified CBS messages.
Interval between sending of two CBS messages.
Number of transmitted CBS messages.
Coding scheme of a CBS message.
Area for transmitting a CBS message.
Type of emergency CBS messages.

Content of a emergency message.
If "Emergency Broadcasting Type" is set to "Earthquake", this parameter is defined as "Earthquake".
If "Emergency Broadcasting Type" is set to "Tsunami", this parameter is defined as "Tsunami".
If "Emergency Broadcasting Type" is set to "Hurricane", this parameter is defined as "Hurricane".
If "Emergency Broadcasting Type" is set to "Other", this parameter is defined by customers.
Content of a normal CBS message.
Name of the NodeB
Number of the CCP port. For detailed information of this parameter, refer to 3GPP TS 25.430.
When the NCP/CCP is based on ATM, set Bearing link type to SAAL. When the NCP/CCP is based on IP, set Bearing link typ
Preferred type of the link used to carry a link when the bearer link type is SAAL-SCTP. When the current bearer link fails, it wil
When the CCP is ATM to ATM-IP, set link change type to ATMTODUAL. When the CCP is based on IP to ATM-IP, set link cha
Mode of file output.

Period of new file generation.
Identifying a cell name

Sum of the maximum transmit power of all DL channels in a cell. For detailed information of this parameter, refer to 3GPP TS
Indicating peer cell is valid or not.
Indicating the corresponding peer cell ID of the cell in a RNCPOOL in RNC Node Redundancy function.
Represent an index for a Operator Group.

Indicating whether the UL frequency of the cell need be configured. TRUE indicates that the UL frequency need be configured
25.433.
Additional frequencies: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
Band5:
General frequencies: [4132-4233]
Additional frequencies: {782, 787, 807, 812, 837, 862}
Band6:
Additional frequencies: {812, 837}
Band7:
Additional frequencies: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
Band8:
Additional frequencies: none
Band9:
BandIndNotUsed:
[0-16383]
Uplink UARFCN of a cell.
Suppose the Uplink UARFCN is unspecified and the value of [Band indication] is Band1, Band2, Band3, Band4, Band5, Band6
If the DL frequency belongs to common frequencies, then
Band1: Uplink UARFCN = Downlink UARFCN - 950
If the DL frequency belongs to special frequencies, then
For detailed information of this parameter, refer to 3GPP TS 25.433.
Depending on the value of [Band indication], as shown below:
Band1
Band2
Additional frequencies: {412,437,462,487,512,537,562,587,612,637,662,687}
Band3
Band4
Band5
Additional frequencies: {1007, 1012, 1032,1037, 1062, 1087}
Band6
Band7
Band8
Band9
BandIndNotUsed:[0-16383]
Downlink UARFCN of a cell.For detailed information of this parameter, refer to 3GPP TS 25.433.
Difference between the System Frame Number (SFN) and NodeB Frame Number (BFN) of the NodeB which the cell belongs
This parameter defines the times of successive in-sync indications required for the NodeB to trigger the radio link recovery pro
recovery process, which indicates that the radio link set has been synchronized. Once the radio link recovery process is trigge
This parameter defines the times of successive in-sync indications required for starting the radio link failure timer. When the ra
successive in-sync indications of the number defined by NInsyncInd.When the timer expires, the NodeB triggers the radio link
Radio link failure timer duration. When the radio link set is in the synchronized state, the NodeB starts the timer after it receive
expires, the NodeB triggers the radio link failure process, and indicates which radio link set is out-of-sync.
Sequence Number of a DL primary scrambling code in a cell. For detailed information of this parameter, refer to 3GPP TS 25.4
This parameter indicates whether transmission diversity configuration of the cell's downlink common physical channels is activ
Indicating which service priority group this cell belongs to. The service priorities of services in this cell can be obtained through
Name of the NodeB
Uniquely identifying a local cell. For detailed information of this parameter, refer to 3GPP TS 25.401.
Identifies a location area code for a Public Land Mobile Network (PLMN) of the GSM-MAP type. It is defined by the operator. F
MCC,MNC,LAC and SAC together compose the Service Area ID (SAI). SAI = MCC || MNC || LAC || SAC. The SAI is used to d
of this parameter, refer to 3GPP TS 23.003.
This parameter indicates whether RAC is configured. If the RNC supports the PS domain, the value of this parameter must be
Identifying a routing area in a location area for a Public Land Mobile Network (PLMN)of GSM-MAP type. It is defined by the op
This parameter indicates whether STTD TX diversity is supported.
This parameter indicates whether the closed loop TX diversity mode 1 supported.
The parameter takes for adjusting the phase and amplitude of the DL dedicated channel upon reception of response from the
Specifies the TX diversity mode on DPCH for the non-MIMO users and non-DC-HSDPA users.
Specifies the TX diversity mode on F-DPCH for the non-MIMO users and non-DC-HSDPA users.
According to the protocol 3GPP TS 25.211, the F-DPCH can use STTD TX diversity mode only. For details on this parameter,
Specifies the TX diversity on DPCH mode for the MIMO users.

Specifies the TX diversity mode on F-DPCH for the MIMO users.
Specifies the TX diversity mode for the DC-HSDPA users.
According to the protocol 3GPP TS 25.211, the DC-HSDPA feature can use STTD TX diversity mode only. For details, see 3G
This parameter works with the offset of neighboring cell-oriented Cell Individual Offset (CIO). It is used for intra- or inter-freque
This switch defines whether a video phone is barred in a cell. If a video phone is allowed in a confidential zone such as a milita
Whether a cell supports Dynamic Spectrum Sharing (DSS)
Maximum transmit power of a cell that is enabled with Dynamic Spectrum Sharing (DSS) and in small DSS coverage.
The parameter specifies the priority of a terminal type. This parameter is used only to identify terminals. The parameter Hierarc
Number of UTRAN Registration Areas (URAs) which the cell belongs to
A cell can belong to multiple URAs. This parameter indicates the ID of the first URA that the cell belongs to. The URA is used
A cell can belong to multiple URAs. This parameter indicates the ID of the second URA that the cell belongs to. The URA is us
A cell can belong to multiple URAs. This parameter indicates the ID of the third URA that the cell belongs to. The URA is used
A cell can belong to multiple URAs. This parameter indicates the ID of the fourth URA that the cell belongs to. The URA is use
A cell can belong to multiple URAs. This parameter indicates the ID of the fifth URA that the cell belongs to. The URA is used
A cell can belong to multiple URAs. This parameter indicates the ID of the sixth URA that the cell belongs to. The URA is used
A cell can belong to multiple URAs. This parameter indicates the ID of the seventh URA that the cell belongs to. The URA is u
A cell can belong to multiple URAs. This parameter indicates the ID of the eighth URA that the cell belongs to. The URA is use
Indicating whether the cell supports the CBS service

A CBS Operator of the cell
CBS service area which the cell belongs to. The cell can belong to only one CBS service area.
TX power of the PCPICH in a cell. This parameter should be set based on the actual system environment such as cell coverag
soft handover areas stipulated in the network planning. For detailed information of this parameter, refer to 3GPP TS 25.433.
PCPICH transmit power of a cell that is enabled with Dynamic Spectrum Sharing (DSS) and in small DSS coverage.
Offset of the PSCH transmit power from the PCPICH transmit power in a cell.
Offset of the SSCH transmit power from the PCPICH transmit power in a cell.
TX power of the SCPICH in a cell.
Name of a cluster. A cluster name is unique within one RNC.

Name of the NodeB
Whether a cell participates in frame protocol (FP) synchronization of the cluster to which the cell belongs.
Maximum TX power of the PCPICH in a cell. This parameter should be set based on the actual system environment such as c
Minimum TX power of the PCPICH in a cell. This parameter should be set based on the actual system environment such as ce
Maximum transmit power on a FACH that carries an MCCH for IMB services. The MCCH for IMB services is carried on a FAC
TX power of the MICH.For details about this parameter, refer to the 3GPP 25.433.
Indicating whether the cell is reserved for operators. If the status of cell is NOT_BARRED, and the cell is reserved for operator
this parameter, refer to 3GPP TS 25.331.
Indicating whether the cell is reserved for extension. If [Cell barred indicator] is NOT_BARRED, and the cell is not reserved for
Indicating whether the UE allocated with Access Class 0 can be allowed to initiate access to the radio network. The UE judges
Indicating whether the UE allocated with Access Class 1 can be allowed to initiate access to the radio network.The UE judges
Indicating whether the UE allocated with Access Class 10 can be allowed to initiate access to the radio network.The UE judge
Indicating whether the UE allocated with Access Class 12 can be allowed to initiate access to the radio network. The UE judge
Indicating whether the UE allocated with Access Class 15 can be allowed to initiate access to the radio network. The UE judge
Indicating whether the UE in idle mode is allowed to access the cell. When the cell status is BARRED, it indicates that the UEs
Indicating whether the UE in idle mode is allowed to reselect another intra-frequency cell. This parameter is valid when [Cell b
NOT_ALLOWED, the UE in idle mod cannot select another intra-frequency cell. The indicator can be neglected in case of eme
This parameter is valid when [Cell barred indicator for SIB3] is BARRED. It indicates that the delay of the cell can be measure
trying to read the cell bar status. For detailed information, refer to 3GPP TS 25.331.
Indicating whether the UE in connected mode is allowed to access the cell. When the cell status is BARRED, it indicates that t
Indicating whether the UE in idle mode is allowed to reselect another intra-frequency cell. This parameter is valid when [Cell b
NOT_ALLOWED, the UE in idle mod cannot select another intra-frequency cell. The indicator can be neglected in case of eme
This parameter is valid when [Cell barred indicator for SIB4] is BARRED. It indicates that the delay of the cell can be measure
refer to 3GPP TS 25.331.
This parameter indicates whether RAC is configured. If the RNC supports the PS domain, the value of this parameter must be
The above values of the algorithms represent the following information:
CRD_ADCTRL: Control Cell Credit admission control algorithm.
Only when NODEB_CREDIT_CAC_SWITCH which is set by the SET UCACALGOSWITCH command and this switch are on,t
HSDPA_UU_ADCTRL: Control HSDPA UU Load admission control algorithm. This swtich does not work when uplink is beare
HSDPA_GBP_MEAS: Control HSDPA HS-DSCH Required Power measurement.
HSDPA_PBR_MEAS: Control HSDPA HS-DSCH Provided Bit Rate measurement.
HSUPA_UU_ADCTRL: Control HSUPA UU Load admission control algorithm. This switch does not work when uplink is beare
MBMS_UU_ADCTRL: Control MBMS UU Load admission control algorithm.
HSUPA_PBR_MEAS: Control HSUPA Provided Bit Rate measurement.
HSUPA_EDCH_RSEPS_MEAS: Control HSUPA Provided Received Scheduled EDCH Power Share measurement.
EMC_UU_ADCTRL: Control power admission for emergency user.
RTWP_RESIST_DISTURB: Control algorithm of resisting disturb when RTWP is abnormal.
FACH_UU_ADCTRL: Admission control switch for the FACH on the Uu interface. This switch determines whether to admit a u
1. If this switch is enabled: if the current cell is congested due to overload, and the users are with RAB connection requests
procedure succeeds.
2. If this switch is disabled: FACH user admission procedure is initiated without the consideration of cell state.
MIMOCELL_LEGACYHSDPA_ADCTRL: Legacy HSDPA admission control algorithm in MIMO cell.
FAST_DORMANCY_ADCTRL: Control admission for Fast Dormancy user. If this switch is disabled, state transition from CELL
If switches above are selected, the corresponding algorithms will be enabled; otherwise, disabled.
The algorithms with the above values represent are as follow:
ALGORITHM_OFF: Disable uplink call admission control algorithm.
ALGORITHM_FIRST: The load factor prediction algorithm will be used in uplink CAC.
ALGORITHM_SECOND: The equivalent user number algorithm will be used in uplink CAC.
ALGORITHM_THIRD: The loose call admission control algorithm will be used in uplink CAC.
ALGORITHM_OFF: Disable downlink call admission control algorithm.
ALGORITHM_FIRST: The load factor prediction algorithm will be used in downlink CAC.
ALGORITHM_SECOND: The equivalent user number algorithm will be used in downlink CAC.
ALGORITHM_THIRD: The loose call admission control algorithm will be used in downlink CAC.

INTRA_FREQUENCY_LDB: Intra-frequency load balance algorithm. It is also named cell breathing algorithm.Based on the ce
PUC: Potential user control algorithm. Based on the cell load, this algorithm changes the selection/reselection parameters of a
UL_UU_OLC: UL UU overload congestion control algorithm. When the cell is overloaded in UL, this algorithm reduces the cell
DL_UU_OLC: DL UU overload congestion control algorithm. When the cell is overloaded in DL, this algorithm reduces the cell
UL_UU_LDR: UL UU load reshuffling algorithm. When the cell is heavily loaded in UL, this algorithm reduces the cell load in U
should not be inter-RAT handover and AMR service rate reduction.
DL_UU_LDR: DL UU load reshuffling algorithm. When the cell is heavily loaded in DL, this algorithm reduces the cell load in D
should not be inter-RAT handover, AMR service rate reduction and MBMS service power decrease.
OLC_EVENTMEAS: Control OLC event measurement. This algorithm starts the OLC event measurement.
CELL_CODE_LDR: Code reshuffling algorithm. When the cell CODE is heavily loaded, this algorithm reduces the cell CODE l
CELL_CREDIT_LDR:Credit reshuffling algorithm. When the cell credit is heavily loaded, this algorithm reduces the credit load
RAT handover.
INTRA_FREQUENCY_ULB: Intra-frequency load balancing algorithm based on RTWP. CPICH power of a cell is adjusted acc
If INTRA_FREQUENCY_LDB, PUC, ULOLC, DLOLC, ULLDR, UDLLDR, OLC_EVENTMEAS, CELL_CODE_LDR, CELL_CRE

ALGORITHM_REQUIRED: Always reset the mac-hs no matter the cells in question are in the same NodeB or not.
ALGORITHM_DEPEND_ON_LCG: Reset the mac-hs only when the cells in question are in the different local cell group.
This parameter is used to select a feature related to HSPA+.
If a feature is selected, it indicates that the corresponding algorithm is enabled. If a feature is not selected, it indicates that the
determines whether the cell supports the E-FACH/MIMO feature but does not affect the establishment of the E-FACH and the
If E_F_DPCH are selected, the corresponding function will be enabled; otherwise, disabled.

TX_DIVERSITY_ON_TO_OFF:When TX Diversity is on to off,the algorithms of cell capacity auto handle is open.
TX_DIVERSITY_OFF_TO_ON:When TX Diversity is off to on,the algorithms of cell capacity auto handle is open.
NBM_LDC_ALL_UE: When inter-freq handover select user occurs, no need to consider whether target cell support Ue.
NBM_LDC_MATCH_UE_ONLY: When inter-freq handover select user occurs, only consider Ues supported by target cell.
NBM_LDC_MATCH_UE_FIRST: When inter-freq handover select user occurs, first consider Ues supported by target cell.

RSVDBIT1: Control RTWP Anti-interfere algorithm
RSVDBIT2~RSVDBIT16:Reserved Switch
If RSVDBIT1 is selected, the corresponding algorithms will be enabled; otherwise, disabled.
Reserved parameter 2
The parameter specifies whether to enable the offload function in a cell.
This parameter specifies whether to enable the fairness-based BE rate reduction algorithm.
Maximum rate of the narrowband AMR speech service for gold users.
Maximum rate of the narrowband AMR speech service for silver users
Maximum rate of the narrowband AMR speech service for copper users.
Maximum rate of the wideband AMR speech service for gold users
Maximum rate of the wideband AMR speech service for silver users
Maximum rate of the wideband AMR speech service for copper users
Defining the radio environment type of the cell, such as a typical town cell, urban cell, and mountain area cell.
The percentage of the conversational non-AMR service threshold to the 100% uplink load. It is applicable to algorithm 1 and a
accessed. If the UL load of a cell is higher than this threshold after the access of a non-AMR speech service, this service will b
The UL load factor thresholds include parameters of [UL threshold of Conv non_AMR service], [UL handover access threshold
of the conversational non-AMR service.
The percentage of the conversational non-AMR service threshold to the 100% uplink load. It is applicable to algorithm 1 and a
accessed. If the UL load of a cell is higher than this threshold after the access of a non-AMR speech service, this service will b
The percentage of other service thresholds to the 100% uplink load. The services refer to other admissions except the convers
accessing, the RNC evaluates the measurement value of the uplink load after the service is accessed. If the UL load of a cell i
of other services.
The percentage of the conversational AMR service threshold to the 100% downlink load. It is applicable to algorithm 1 and alg
the DL load of a cell is higher than this threshold after the access of an AMR speech service, this service will be rejected. If the
The DL load factor thresholds include parameters of [DL threshold of Conv non_AMR service], [DL handover access threshold
of the conversational AMR service.
The percentage of the conversational non-AMR service threshold to the 100% downlink load. It is applicable to algorithm 1 and
accessed. If the DL load of a cell is higher than this threshold after the access of a non-AMR speech service, this service will b
The percentage of other service thresholds to the 100% downlink load. The services refer to other admissions except the conv
is accessing, the RNC evaluates the measurement value of the downlink load after the service is accessed. If the DL load of a
of other services.
The percentage of the handover service admission threshold to the 100% uplink load. It is applicable to algorithm 1 and algori
load of a cell is higher than this threshold after the access, this service will be rejected. If the UL load of a cell will not be highe
The percentage of the handover service admission threshold to the 100% downlink load. It is applicable to algorithm 1 and alg
the DL load of a cell is higher than this threshold after the access, this service will be rejected. If the DL load of a cell will not b
Admission threshold of total cell uplink power. This parameter is related to the target load of the uplink schedule.
Admission threshold of the total cell downlink power. If the value is too high, too many users will be admitted. However, the thr
The admission control decision is only for dedicated channels. For common channels, some resources instead of a special ad
In the UL, according to the current load factor and the characteristics of the new call, the UL CAC algorithm predicts the new tr
threshold. If the value is not higher than the threshold, the call is admitted; otherwise, rejected.
Different admission policies are used for dedicated channel and common channel users. For common channel users, resource
the assumption of admitting the new call, then plus with the premeditated common channel DL load factor to get the predicted
When the algorithm 2 is used, this parameter defines the total equivalent user numbers corresponding to the 100% uplink load
When the algorithm 2 is used, this parameter defines the total equivalent user number corresponding to the 100% downlink loa
Threshold of all the HSUPA user PBR whose schedule priority is lower than that of users to be admitted.
Threshold of all the HSUPA user PBR whose schedule priority is the same as that of users to be admitted.
Threshold of all the HSUPA user PBR whose schedule priority is higher than that of users to be admitted.
If the HS-DPCCH carries ACK/NACK, the system will not perform CAC. If the HS-DPCCH carries CQI, the system will perform
Average throughput admission threshold of the HSDPA streaming service. If the sum of PBR of all the accessed streaming us
satisfied and new HSDPA streaming services are not allowed. Otherwise, the QoS can be satisfied and new HSDPA streamin
Average throughput admission threshold of the HSDPA best effort traffic. If the sum of PBR of all the accessed HSDPA BE us
satisfied and new HSDPA BE services are not allowed. Otherwise, the QoS can be satisfied and new HSDPA BE services are
Maximum number of users supported by the HSDPA channel. The user in this parameter refers to the user with services on th
on the cell type and the richness of the available HSDPA power and code resources.
Maximum UL transmit power for conversational service in a specific cell. It is based on the UL coverage requirement of the co
Maximum UL transmit power for the streaming service in a specific cell. It is based on the UL coverage requirement of the stre
The maximum UL transmit power for the interactive service in a specific cell. It is based on the UL coverage requirement of the
The maximum UL transmit power for background service in a specific cell. It is based on the UL coverage requirement of the b
If [Auto-Adaptive Background Noise Update Switch] is set to OFF, it is used to set background noise of the cell. If [Auto-Adapt
When the RNC is performing downlink open power control, it evaluates link consumption according to the PCPICH TX power a
When the parameter is 'OFF', the auto-adaptive background noise update algorithm is switched off. Otherwise, the algorithm is
Only when the measured background noise's duration reaches this parameter, the output of the auto-adaptive background noi
regarded as the effective background noise.
When the number of uplink equivalent users is not larger than this parameter, the RTWP could be regarded as background no
same time, the auto-adaptive status should be reset.
Maximum number of users supported by the HSUPA channel. The user in this parameter refers to the user with services on th
on the cell type and the richness of the available HSUPA power and code resources.
Reserved DL power factor for HSUPA user. The higher the value is, the more resources reserved for the HSUPA control chan
Reserved DL power factor for MBMS service.

Available guarantee power of all the MTCHs. This parameter is a protection for the MBMS PTM bearing. When the power of a
resources may be consumed by the MBMS PTM bearing and too little capacity is left for the non-MBMS services.
Available guarantee codes of all the MTCHs. This parameter is a protection for the MBMS PTM bearing.
Available guarantee codes of all the MTCHs. This parameter is a protection for the MBMS PTM bearing. When the codes of al
resources may be consumed by the MBMS PTM bearing and too little capacity is left for the non-MBMS services.
Maximum code limit of all the MTCHs. This parameter is a limit to the maximum bearing of the MBMS PTM bearing. When the
system resources may be consumed by the MBMS PTM bearing and too little capacity is left for the non-MBMS services.
Uplink Credit Reserved by Spread Factor for HandOver. SFOFF means that none of them are reserved for handover.
Some cell resources can be reserved for handover UEs to guarantee handover success rate and improve access priority of ha
corresponding credit resource are reserved.
(1) This parameter, along with the [Algorithm stop time], is used to limit the validation time of the background noise automatic u
[Algorithm start time] each day. In other periods, the algorithm fails. If [Algorithm stop time] is less than [Algorithm start time], a
fails.
(2) Input format: HH&MM&SS
(1) This parameter, along with the [Algorithm start time], is used to limit the validation time of the background noise automatic
[Algorithm start time] each day. In other periods, the algorithm fails. If [Algorithm stop time] is less than [Algorithm start time], a
fails
(2) Input format: HH&MM&SS
The difference of RTWP that trigger the update of background noise. If the difference is larger than the threshold, the backgro
This parameter is applied when "BGNSwitch" is set to ON. (1) If the difference of measured background noise without filtered a
the background noise will not be updated.
The parameter indicates the max user number the EFACH channel can supports.
Used to check whether the number of equivalent users is overlarge in a cell. If the rate of equivalent users to total equivalent u
users is not overlarge, and the switch of RTWP anti-interference algorithm is enabled, the RTWP anti-interference algorithm is
Max ERACH UE NumberMaximum number of UEs that can access a cell using the ERACH function.
Power resource reserved for free users. The total guaranteed power for free user groups must not exceed this parameter valu
Threshold of the maximum guaranteed power for HSDPA users. This threshold limits the power that can be used by HSDPA u
Threshold of the maximum guaranteed power for HSUPA users. This threshold limits the power that can be used by HSUPA u
Uniquely identifying a cell. For detailed information of this parameter, refer to 3GPP TS 25.401.

Together with PLMN code and LAC, uniquely corresponding to a cell.
When ON,the message is valid.When OFF,the message is invalid.
When ON,the message is valid.When OFF,the message is invalid.
Unique ID of a cell
CM type of the cell.

The CM parameters are configured on the basis of the CM type of the cell. That is, the CM sequence number is determined af
Downlink compressed mode (CM) implementation mode selection threshold.
When the downlink spreading factor is greater than or equal to the value of this parameter, the SF/2 mode is preferred. Otherw
The SF/2 mode consumes more system resources and therefore this mode is recommended only for low-rate users. The high
recommended only when the SF/2 approach is unavailable or there are high-rate users.
Uplink CM implementation mode selection threshold.
When the uplink spreading factor is greater than or equal to the value of this parameter, the SF/2 mode is preferred. Otherwise
The relative power margin of single BE traffic, used to calculate the triggering threshold of event F, can avoid the fluctuation of
The relative power margin of combined traffics, used to calculate the triggering threshold of event F, can avoid the fluctuation o
Maximum UL rate when coverage of the entire cell is ensured under certain load. For a BE service that has a low maximum ra
Maximum DL rate during network planning when coverage of the entire cell is ensured. When the DL TCP is limited, the curren
processing. Thus, the DCCC algorithm is applied to BE services whose maximum DL rate is greater than the threshold.
Unique ID of a cell
This parameter specifies whether the distance based RRC redirection algorithm is valid. The algorithm is valid only when the s
Redirection algorithm works only when the propagation delay between UE and NodeB is larger then this threshold. For details
When the UL load state or DL load state of the serving cell is LDR(basic congestion) or OLC(overload congestion), a UE may
redirection is not performed if the load state on the serving cell is LDR or OLC.
When the load of the serving cell is within the normal range, a UE may be redirected to another cell according to the distance
normal range.
Unique ID of a cell
Maximum number of inter-RAT RAB directed retries. It decides the size of the candidate set for inter-RAT DRD. The value 0 in
Whether the service steering DRD algorithm is applied.

Whether the load balancing DRD algorithm is applied to DCH services.
- ON: The load balancing DRD algorithm will be applied.
- OFF: The load balancing DRD algorithm will not be applied.
Whether the load balancing DRD algorithm is applied to HSDPA services.
- ON: The load balancing DRD algorithm will be applied.
Whether load balancing DRD is based on power or on user number.
- Power: Power(Downlink none-HSDPA power is used for DCH services, and downlink HSDPA guarantee power is used for H
- UserNumber: User number(Downlink R99 equivalent user number is used for DCH services, and downlink HSDPA user num
Downlink load threshold to trigger load balancing DRD for DCH services. The load balancing DRD will be triggered only when
Downlink load threshold to trigger load balancing DRD for HSDPA services. The load balancing DRD will probably be triggered
Whether to apply the code balancing DRD algorithm. The "DR_RAB_SING_DRD_SWITCH" parameter in "SET UCORRMALG
One of the triggering conditions of code balancing DRD. The other condition is the code occupancy threshold. Code balancing
One of the triggering conditions of code balancing DRD. The other condition is the minimum spreading factor. Code balancing
Frequency band of the target UL and DL UARFCNs to which the UE is redirected. It is recommended that this parameter is se
redirection is initiated in the current cell when the UARFCN to which the UE is redirected is the same as that of the current cel
Whether the target UL UARFCN to which the UE is redirected needs to be configured. TRUE indicates that the UL UARFCN n
Special UARFCNs: none
BAND4
Common UARFCNs: [1312-1513]
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
Special UARFCNs: {812, 837}
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
BandIndNotUsed: [0-16383]
If the UL UARFCN is not manually configured, if RedirBandInd is set to BAND1, BAND2, BAND3, BAND4, BAND5, BAND6, B
If the DL UARFCN is a common UARFCN, the relation between the UL UARFCN and the DL UARFCN is as follows:
BAND1: UL UARFCN = DL UARFCN - 950
If the DL UARFCN is a special UARFCN, the relation between the UL UARFCN and the DL UARFCN is as follows:
Target DL UARFCN for the RRC redirection. Different values of "RedirBandInd" correspond to different value ranges of the UA
This parameter specifies whether to enable the uplink load balance for DC-HSDPA traffic. The uplink load balance is performe
This parameter specifies the threshold of triggering the uplink load balance for DC-HSDPA traffic. If the remaining number of e
The parameter specify Whether to enable the terminal type hierarchy algorithm.
Unique ID of a cell
Whether to enable DRD for technological satisfaction of non-MIMO legacyH in STTD mode.
Whether to enable DRD for technological satisfaction of non-MIMO legacyH in primary and secondary CPICH mode.
Reference CQI for determining the channel condition by comparing with the CQI threshold during RAB setup.
CQI threshold for determining that the channel condition is Excellent.
CQI threshold for determining that the channel condition is Good.
CQI threshold for determining that the channel condition is Bad.
Specifies the index of the telecom operator.
Specifies whether to impose the access restriction on the CS domain.
Specifies whether to impose the access restriction on the PS domain.
Specifies the mode of restricting the access classes.

Specifies the access classes that are restricted according to the fixed restriction mode.
Specifies the number of access classes that are restricted at a time according to the flexible polling restriction mode.
Specifies the access classes that are restricted according to the flexible polling restriction mode.
Specifies the interval delay between consecutive pollings according to the flexible polling restriction mode.
Whether the dynamic shutdown algorithm is enabled in a cell. ON_1, ON_2, and ON_3 indicate that one, two, and three shutd
Start time of the first interval when the cell dynamic shutdown feature is valid.
End time of the first interval when the cell dynamic shutdown feature is valid.
Start time of the second interval when the cell dynamic shutdown feature is valid.
End time of the second interval when the cell dynamic shutdown feature is valid.
Start time of the third interval when the cell dynamic shutdown feature is valid.
End time of the third interval when the cell dynamic shutdown feature is valid.
Type of cell dynamic shutdown. When this parameter is set to FORCESHUTDOWN, the cell is shut down unconditionally in ea
to QOSSHUTDOWN, the RNC attempts to shut down a cell in each cell shutdown period if the load of a neighboring cell is so
Threshold for the total number of DCH and CCH users in a cell. The RNC attempts to shut down a cell when the number of DC
Threshold for the number of HSDPA (including DC-HSDPA) users in a cell. The RNC attempts to shut down a cell when the nu
Threshold for the number of HSUPA (including DC-HSUPA) users in a cell. The RNC attempts to shut down a cell when the nu
Threshold for load margin of a neighboring cell. The RNC attempts to shut down a cell when the load margin of a neighboring
High-priority scheduling indicator. after this cell is shut down based on QoS, throughput of high-priority HSDPA users determin
Determines duration for which the UE waits until no data is received to UEs in CELL_FACH state and Discontinuous Receptio
Determines the length of a DRX Cycle for UEs in CELL_FACH state and DRX mode. For details, see 3GPP TS 25.331.
Determines the period within a DRX Cycle for which UEs in CELL_FACH state and DRX mode continuously receive HS-DSCH
Whether the DRX operation can be interrupted by HS-DSCH data for UEs in CELL_FACH state and DRX mode. For details, s
This parameter specifies the maximum guaranteed power of the DTCH mapped onto the EFACH.
This parameter specifies the power offset between HS-SCCH and P-CPICH when BCCH is mapped onto the EFACH.
When UE is in Enhanced CELL_FACH state, the data on the BCCH is also sent on the HS-PDSCH. Meanwhile, the HS-SCCH
This parameter specifies the transmission power of the HS-PDSCH that sends the data carried on the BCCH. When UE receiv
The MAC-c on Iub interface will increase after the Enhanced CELL_FACH is supported in the cell. When the UE enters the En
The MAC-c flow on the Iub interface will increase after Enhanced CELL_FACH is supported in the cell. When the UE enters th
The MAC-c flow on Iub interface will increase after the Enhanced CELL_FACH is supported in the cell. When the UE enters th
Size index of the first transmission block (TB) transmitted in blind transfer that uses HS-SCCH Less Paging when the EPCH fu
Size index of the second TB transmitted in blind transfer that uses HS-SCCH Less Paging when the EPCH function is enabled
Offset of HS-SCCH power against P-CPICH power. The power offset is provided for EPCH UEs.
Offset of HS-PDSCH power against P-CPICH power when the EPCH function is enabled.
Number of transmissions during which the PCCH sends the Paging Type 1 message when the EPCH function is enabled.
Offset of Time of Arrival Window Start Point (TOAWS) against TOA Window Endpoint (TOAWE) for downlink data frames.
Offset of TOAWE against Latest Time of Arrival (LTOA) for downlink data frames.
Maximum EPCH access rate. The parameter value times "EPCH Activation Factor" equals Iub bandwidth that is applied when
Unique ID of a cell
Rate threshold for the decision to set up a PS domain background/interactive service on the DCH in the uplink. Only when the
specifications, only the background/interactive services whose rate is lower than 16 kbit/s can be carried on the CCH. Therefo
Rate threshold for the decision to set up a PS domain background/interactive service on the DCH in the downlink. Only when t
the specifications, only the background/interactive services whose rate is lower than 16 kbit/s can be carried on the CCH. The
This parameter specifies whether the DL code-resource-saving mode is applicable to narrowband AMR services, TRUE specif
maximum bit rate of single AMR service is lower than or equal to 7.95 kbit/s, while SF128 is used if the code-resource-saving
Threshold for determining the signal quality in a cell. If the reported Ec/No exceeds the value of this parameter, you can infer t
Time duration when the reported Ec/No is valid. The reported Ec/No is valid for the period (starting from the time when the Ec/
Whether to configure the cell-level SRB channel type for an RRC connection establishment.
Index of Signaling Radio Bearer (SRB) channel type for an RRC connection establishment. Each index corresponds to a set o
ID of an RNC
Indicating whether the UL frequency of the cell need be configured. TRUE indicates that the UL frequency need be configured
25.433.
Band5:
Additional frequencies: {782, 787, 807, 812, 837, 862}
Band6:
Band7:
Band8:
Band9:
BandIndNotUsed:
[0-16383]
Uplink UARFCN of a cell.
Suppose the Uplink UARFCN is unspecified and the value of [Band indication] is Band1, Band2, Band3, Band4, Band5, Band6
If the DL frequency belongs to common frequencies, then
Depending on the value of [Band indication], as shown below:
Band1
Band2
Additional frequencies: {412,437,462,487,512,537,562,587,612,637,662,687}
Band3
Band4
Band5
Additional frequencies: {1007, 1012, 1032,1037, 1062, 1087}
Band6
Band7
Band8
Band9
BandIndNotUsed:[0-16383]
Downlink UARFCN of a cell.For detailed information of this parameter, refer to 3GPP TS 25.433.
When the parameter is set to INACTIVE, the GPS frame timing measurement is not activated. When the parameter is set to A
Indicating whether HCS is used. For details, refer to 3GPP TS 25.304.

HCS priority of the cell belongs to. The parameter depends on HCS rules. For details, refer to 3GPP TS 25.304.
Intra-system HCS cell reselection start threshold. When Srxlev of the serving cell is less than this parameter, the UE starts the
Inter-system HCS cell reselection start threshold. When Srxlev of the serving cell is less than this parameter, the UE starts the
Quality threshold of HCS cell reselection. It can be used to calculate the quality level of the specified cell in HCS reselection H
Maximum duration of cell reselection. This parameter, along with the [Max number of cell reselection], is used for rate evaluati
Maximum number of cell reselection. This parameter, along with the [Time for evaluating max cell reselection], is used for rate
Time before reverting to low-mobility measurement. For detailed information of this parameter, refer to 3GPP TS 25.304.
The UE does not start the inter-RAT measurement if it detects that the quality of the serving cell is higher than this threshold. F
Unique ID of a cell
Switch of the algorithm for UE speed estimation. This parameter indicates whether the UE speed estimation is allowed in this c
The value ON indicates that the UE speed estimation is allowed in this cell.
The value OFF indicates that the UE speed estimation is not allowed in this cell.
Note: The UE speed estimation cannot be triggered even if this switch is set to ON in either of the following cases: The cell is n
Time window for estimating whether the UE is in high-mobility state.

The start point of the estimation is the moment of the last reporting of event 1D, and the backdated time length is determined b
Threshold for determining whether the UE is in high-mobility state.

After the UE reports event 1D, the UE is considered in high-mobility state if the number of changes of the best cell during "TFa
Period for determine whether the UE is in low-mobility state.
The RNC periodically determines whether the UE is in low-mobility state. The smaller the value is, the more frequently the stat
Time window for deciding whether the UE is in low-mobility state.

Every time the slow speed period timer expires, the RNC estimates whether the UE is in low-mobility state. This parameter spe
Threshold for determining whether the UE is in low-mobility state.

After the UE reports event 1D, the UE is considered in low-mobility state if the number of changes of the best cell is smaller th
Time window for determining whether ping-pong handover occurs in the best cell during the UE speed estimation.
In the speed estimation algorithm, an algorithm is adopted to avoid inaccurate estimation caused by frequent handovers of be
The given time length is set by this parameter. If this parameter is set too great, the RNC may mistakenly determine that ping-
Unique ID of a cell
Cell-level switch for controlling inter-frequency and inter-RAT handover.
When inter-frequency and inter-RAT cells coexist, the parameter should be configured according to actual handover policies.
When INTERFREQ is selected, only inter-frequency neighboring cells are measured and inter-frequency handover is performe
When INTERRAT is selected, only GSM neighboring cells are measured and inter-RAT handover is performed.
When SIMINTERFREQRAT is selected, both inter-frequency and inter-RAT cells are measured, and the handover is performe
This parameter specifies the event 2D/2F measurement threshold of which measurement type (inter-frequency or inter-RAT m
When COEXIST_MEAS_THD_CHOICE_INTERFREQ is selected, event 2D/2F measurement thresholds oriented towards inte
When COEXIST_MEAS_THD_CHOICE_INTERRAT is selected, event 2D/2F measurement thresholds oriented towards inter-
The factors such as the event 2D/2F measurement thresholds for inter-frequency measurement and inter-RAT measurement,
inter-frequency measurement, and inter-frequency neighboring cells are preferred when inter-RAT and inter-frequency neighb
Whether the cell allows inter-RAT handover for CS services.
When the switch is set to ON, the inter-RAT handover for CS services is enabled. When the switch is set to OFF, the inter-RA
Based on the Service Handover Indicator of a service and the related parameter configurations on the network side, related m
Note that the service handover is triggered only when the Service Handover Indicator is set to HO_TO_GSM_SHOULD_BE_P
Whether the cell allows inter-RAT handover for PS services.
When the switch is set to ON, the inter-RAT handover for PS services is enabled. When the switch is set to OFF, the inter-RAT
Based on the Service Handover Indicator of a service and the related parameter configurations on the network side, related m
Note that the service handover is triggered only when the Service Handover Indicator is set to HO_TO_GSM_SHOULD_BE_P
If Manual is chosen, parameter " Code Number for HS-PDSCH " determines HS-PDSCH code number to be allocated. If Auto
25.308.
The parameter specifies the number of HS-DPSCH codes. This parameter is valid only when "Allocate Code Mode" is set to "M
The parameter determines the maximum number of HS-PDSCH codes (SF=16). This parameter is valid only when "Allocate C
is idle or busy. When the code resource used by the non-HSPA services is little, the HS-PDSCH uses the rest idle codes as m
The parameter specifies the minimum number of the HS-PDSCH codes (SF=16). This parameter is valid only when "Allocate C
code tree. When the non-H services need more code resources, the non-H service will gradually occupy the codes used by th
This parameter decides the maximum number of subscribers that the NodeB can schedule in a TTI period. For detailed inform
This parameter specifies the offset between the total HSPA power and the maximum transmission power of a cell. The total H
This parameter named Measure Power Offset Constant is used to compute measurement power offset. Measurement power o
Measure Power Offset = Max(-6, Min(13,CellMaxPower - PcpichPower - Measure Power OffsetConstant)). For details of the IE
Indicating whether HARQ Preamble is supported. For detailed information of this parameter, refer to 3GPP TS 25.308.
This parameter specifies code reshuffling switch for HDSPA. If the switch is set as ON, codes occupied by the R99 service can
codes can be used by HSDPA and thus HSDPA throughput can be improved.
H-based code tree reshuffle user number threshold. When the switch "Code Adjust Switch for HSDPA"is enabled, if the numbe
on lots of users at a time is avoided.
This parameter is used for setting the punish timer length for code adjust for hsdpa.
Measure power offset (MPO) constant for calculating MPO. The formula is as follows: MPO = Max(-6, Min(13, CellMaxPower -
the transmit power of both PCPICH and SCPICH.
CQI power offset from the UL DPCCH when the UE is in the single-RLS state. When the value is set too low, CQI resolution o
CQI power offset from the UL DPCCH when the UE is in the multi-RLS state. When the value is set too low, CQI resolution of
Number of CQI retransmissions when the UE is in the single-RLS state. Assume that the CQI repetition factor is N. The receiv
Number of CQI retransmissions when the UE is in the multi-RLS state. Assume that the CQI repetition factor is N. The receive
Duration of a CQI feedback cycle when the UE is in the single-RLS state. In each CQI feedback cycle, the UE retransmits CQI
Duration of a CQI feedback cycle when the UE is in the multi-RLS state. In each CQI feedback cycle, the UE retransmits CQI
Period of sending the channel quality indication (CQI) feedback of conversational services.
Period of sending the channel quality indication (CQI) feedback of non-conversational services in MIMO mode without DC-HA
Period of sending the channel quality indication (CQI) feedback of non-conversational services in MIMO+DC-HSDPA mode, e
The parameter specifies the number of codes (SF=256) used by the E-DCH Absolute Grant Channel (E-AGCH). For details ab
The parameter specifies the number of codes (SF=128) used by the E-DCH Relative Grant Channel (E-RGCH)/E-DCH Hybrid
RNC receives from the E-DCH is correct or not. The E-RGCH and E-HICH are dedicated channels shared by multiple UEs. Th
For details about this parameter, refer to 3GPP TS 25.433.
The parameter specifies the target value of the uplink load. HSUPA power control on the NodeB side keeps uplink load close t
This parameter specifies the ratio of the non-serving E-DCH RX power to the total E-DCH RX power. The parameter indicates
ID of an RNC
Cell ID before modification
New cell ID
Unique ID of a cell
Cell-oriented inter-frequency measurement report mode
If this parameter is set to PERIODICAL_REPORTING, measurement reports are periodically reported. If this parameter is set
There are two inter-frequency handover report modes in the RNC, namely, event-triggered report and periodical report. The re
Event-triggered report mode
In this mode, event 2B is used to decide whether to trigger inter-frequency handover. This prevents the ping-pong handover (T
trigger threshold"). Event 2B cannot change from event-triggered mode to periodical mode. When event-triggered measureme
load are saved. Comparing the signal quality between intra-frequency and inter-frequency handovers, the ping-pong effect in h
each time when the best cell is updated, the inter-frequency measurement parameters should be updated accordingly.
Periodical report mode
In this mode, event 2D/2F is used to start and stop the compressed mode, and to periodically report the inter-frequency cell m
timer expires, the inter-frequency handover is started after the timer expires.
If the handover fails, the handover decision is performed, according to the periodical inter-frequency measurement report.
The advantage of the periodical measurement report mode is that it can repeatedly perform direct retry on the same cell when
handover decision is performed in the RNC. The disadvantage of the periodical measurement report mode is that it requires la
As for the impact on network performance,the two measurement report modes have both advantages and disadvantages. Cur
This parameter specifies the Layer 3 filter coefficient for the inter-frequency measurement
This parameter has the same physical significance and measurement model as the layer 3 filter coefficient for the intra-freque
can be adjusted according to performance statistics.
Interval between periodic reporting for the inter-frequency handover.

In periodic reporting mode, the inter-frequency handover attempts is reported at the preset interval. It is not recommended tha
have high load when processing signaling. If the interval is too long, the network cannot detect the signal changes in time. Thi
Hysteresis for triggering event 2B.

The value of this parameter is associated with the slow fading. If this parameter is set to a greater value, the ability of resisting
Hysteresis for triggering event 2D.

The value of this parameter is associated with the slow fading. If this parameter is set to a greater value, the probability of ping
When "InterFreqReportMode" is set to PERIODICAL_REPORTING, the hysteresis in active set quality measurement is used t
than the threshold). Event 2D is used to enable the compression mode and event 2F is used to disable the compression mode
frequency handover.
To set "Hystfor2D" and "Hystfor2F", you should consider the radio environment (with slow fading characteristics), actual hando
Hysteresis for triggering event 2F.

frequency handover.
Hysteresis in the inter-frequency hard handover triggered by the periodic measurement report.
This parameter is used to estimate the inter-frequency handover on the RNC side. If this parameter is set to a greater value, th
triggered in time.
The parameter WeightForUsedFreq is the frequency weighting factor used to calculate the quality of the current frequency.
If this parameter is set to a greater value, the higher quality of the active set is obtained. If this parameter is set to 0, the gener
TS 25.331. This parameter is used for event-triggered reporting of inter-frequency handovers for events 2D, 2F, 2B and 2C, bu
Interval time between the detection of event 2B and sending of measurement report. This parameter correlates with slow fadin
interval can effectively reduce the average number of handovers and the number of incorrect handovers, preventing unnecess
rate is less sensitive to this interval. Therefore, for the cell with most of the fast-moving UEs, this parameter can be set to a sm
Interval time between detection of event 2D and sending of the measurement report. This parameter correlates with slow fadin
The emulation results show that setting this interval can effectively reduce the average number of handovers and the number
whereas, for the slow-moving UE, the call drop rate is less sensitive to this interval. Therefore, for the cell with most of the fast
the actual network statistics.
Interval time between detection of event 2F and sending of the measurement report.This parameter correlates with slow fading
Interval between reception of periodical reports and triggering of the inter-frequency handover.
Only the inter-frequency cell in which the signal quality is above a certain threshold in all periodic reports during a time equal to
slow in responding to signal change. The emulation results show that setting this interval can effectively reduce the average nu
more sensitive to this interval, whereas, for the slow-moving UE, the call drop rate is less sensitive to this interval. Therefore, f
can be adjusted according to the actual network statistics.
Ec/No threshold of triggering the inter-frequency measurement for CS services.

The threshold of triggering the inter-frequency measurement (namely, threshold of enabling the compression mode) is a key p
the following factors: moving speed of the UE and cell radius.
When Ec/No is used as the measurement quantity for CS services, the UE reports event 2D when the measured Ec/No value
For the UE moving at a speed of 5 km/h, the recommended threshold is -17 dB; for the UE moving at a speed of 50 km/h, the
For the cell in which the UEs are moving at various speeds, set this parameter to -14 dB. The emulation result shows that the
Event 2D and event 2F are used to enable and disable the compression mode respectively. To enable the compression mode
the thresholds of triggering event 2D and event 2F.
Ec/No threshold of stopping the inter-frequency measurement for CS services.

The threshold of stopping the inter-frequency measurement (namely, threshold of disabling the compression mode) is a key pa
When Ec/No is used as the measurement quantity for CS services, the UE reports event 2F when the measured Ec/No value
Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA services.
When Ec/No is used as the measurement quantity for PS non-HSPA services, the UE reports event 2D when the measured E
Ec/No threshold of triggering the inter-frequency measurement for HSPA services.

When Ec/No is used as the measurement quantity for HSPA services, the UE reports event 2D when the measured Ec/No val
Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA services.

When Ec/No is used as the measurement quantity for PS non-HSPA services, the UE reports event 2F when the measured Ec
Ec/No threshold of stopping the inter-frequency measurement for HSPA services.

When Ec/No is used as the measurement quantity for HSPA services, the UE reports event 2F when the measured Ec/No valu
RSCP threshold of triggering the inter-frequency measurement for CS services.

When RSCP is used as the measurement quantity for CS services, the UE reports event 2D when the measured RSCP value
For the UE moving at a speed of 5 km/h, the recommended threshold is -100 dBm; for the UE moving at a speed of 50 km/h, t
For the cell in which the UEs are moving at various speeds, set this parameter to -95 dBm. The emulation result shows that th
When the signals at the entrance to an elevator or a subway change too fast to perform handover, set this parameter to -90 dB
RSCP threshold of stopping the inter-frequency measurement for CS services.

When RSCP is used as the measurement quantity for CS services, the UE reports event 2F when the measured RSCP value
RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA services.
When RSCP is used as the measurement quantity for HSPA services, the UE reports event 2D when the measured RSCP val
RSCP threshold of triggering the inter-frequency measurement for HSPA services.

RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA services.

When RSCP is used as the measurement quantity for PS non-HSPA services, the UE reports event 2F when the measured R
RSCP threshold of stopping the inter-frequency measurement for HSPA services.

When RSCP is used as the measurement quantity for HSPA services, the UE reports event 2F when the measured RSCP val
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for CS
target frequency is higher than this threshold. If the inter-frequency reporting mode is set to "PERIODIC_TRIGGER", this para
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for HS
when the quality of the target frequency is higher than this threshold. If the inter-frequency reporting mode is set to "PERIODIC
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for no
2B. That is, event 2B can be triggered when the quality of the target frequency is higher than this threshold. If the inter-frequen
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for CS
the quality of the target frequency is higher than this threshold. If the inter-frequency reporting mode is set to "PERIODIC_TRI
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for HS
than the start threshold for event 2D or equal to the threshold of event 2F.
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for no
Threshold of used frequency quality for triggering inter-frequency measurement based on measurement quantity of Ec/No for
for triggering event 2B can be met only when the quality of the uesd frequency is smaller than this threshold. In addition, even
After handover, even if the inter-frequency measurement is triggered again, it is very difficult to hand over the UE again to the
event 2B. One of the necessary conditions for triggering event 2B can be met only when the quality of the used frequency is s
conditions for triggering event 2B can be met only when the quality of the used frequency is smaller than this threshold. In add
Threshold of used frequency quality for triggering inter-frequency measurement based on measurement quantity of RSCP for
for triggering event 2B can be met only when the quality of the used frequency is smaller than this threshold. In addition, even
Length of the timer for the inter-frequency measurement.

If the inter-frequency handover is not performed before this timer expires, the inter-frequency measurement is stopped and the
This parameter is used to prevent the long duration of the inter-frequency measurement state (compression mode) due to una
Sets the interval between the failure in the inter-frequency handover triggered by the event 2B and the inter-frequency handov
Maximum number of inter-frequency handover re-attempts after event 2B is reported when the measurement control message
If this parameter is set to a greater value, the number of inter-frequency handover re-attempts increases and the possibility of
measurement control message to allow the UE to be handed over to other cells of this frequency.
If the measurement control is released, the inter-frequency handover re-attempt is stopped.
Maximum delay before triggering the inter-frequency coverage handover.

If the inter-frequency coverage handover priority of the cell reporting the MR is equal to the highest priority of the target cell de
the measurement control list, the inter-freq coverage handover delay timer is enabled.
When the timer expires, the inter-freq handover is triggered.
Unique ID of a cell
Hysteresis used for event 2C.
Interval time between detection of event 2C and sending of the measurement report.
The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the probability of incorrec
Threshold of the target frequency quality for triggering inter-frequency handover.

This parameter is used for measurement control on event 2C. When the target frequency quality is higher than this threshold,

Interval between the handover re-attempts for event 2C.

If the inter-frequency handover for event 2C fails, the RNC reties the inter-frequency handover. This parameter specifies the in
to the target cell whose load is reduced. The RNC load, however, increases.
Maximum number of handover attempts for event 2C.

This parameter specifies the maximum number of handover re-attempts for event 2C when the measurement control message
the number of re-attempts reaches the preset value, the RNC does not attempt to perform the handover. Alternatively, when th
Unique ID of a cell
Inter-RAT measurement reporting mode.
When PERIODICAL_REPORTING is selected, the periodical reporting is used for inter-RAT measurement. When EVENT_TR
The RNC provides two inter-RAT measurement reporting modes, event-triggered reporting and periodical reporting.
Event-triggered reporting
To avoid the ping-pong effect before and after the inter-RAT handover, use event 3A (quality of the currently used frequency is
the BSIC of the GSM cell whose event 3A needs to be triggered must be decoded correctly by the UE. The reporting mode of
The advantage of event-triggered reporting is that the signaling transmission and processing load are saved. Comparing the s
cannot be changed to periodical reporting. For the cell-oriented algorithm parameters, each time when the best cell is updated
Periodical reporting
When the quality of the GSM cell reported by the UE meets the criteria for inter-RAT handover, the delay trigger timer is starte
For the GSM cell whose BSIC can be decoded correctly, a shorter delay trigger time should be set to indicate the high priority
If the handover fails, the handover re-attempt is made again according to the periodical inter-RAT measurement report.
The advantage of periodical reporting is that it can be used for repeated handover re-attempts on the same cell when the hand
needs not to inform the UEs of the parameter change through signaling messages after the handovers. The drawback of perio
The two reporting modes have both advantage and drawback. Currently, the traditional periodical reporting mode is preferred.
L3 filtering coefficient for event 2D or event 2F measurement

If this parameter is set to a greater value, the effect of smoothing signals and the ability of anti-fast-fading improve. However, t
increases.
The parameter has the same physical meaning and measurement model as the inter-frequency L3 filter coefficient. The report
Parameter adjustment suggestions:
In cells where the average moving speed of UEs is low, there is a comparatively big shadow fading square error. Therefore, th
In cells where the average moving speed of UEs is medium, there is a comparatively smaller shadow fading square error. The
In cells where the average moving speed of UEs is high, there is a comparatively small shadow fading square error. Therefore
Measurement quantity used in coverage-based inter-RAT measurement in event 3A-triggered reporting mode.
When CPICH_Ec/No is selected, it indicates that the Ec/No measurement quantity is used for event 3A measurement. The ph
When CPICH_RSCP is selected, it indicates that the RSCP measurement quantity is used for event 3A measurement. The ph
When AUTO is selected, it indicates that the Ec/No measurement quantity is used for event 3A measurement if the RNC recei
This parameter specifies the Layer 3 filter coefficient for the inter-RAT measurement.
increases.
This parameter is used for event 3A evaluation. For detailed information of this parameter, refer to 3GPP TS 25.133.
To set this parameter, see the method for setting the intra-frequency handover weighting factor "Weight".
Interval that the UE reports inter-RAT measurement results to the RNC.

This parameter specifies the interval that the UE sends inter-RAT measurement results to the RNC in periodical reporting mod
The GSM RSSI measurement period is 480 ms. Therefore, the inter-RAT periodical reporting interval should be longer than 48
The adjustment should be made according to the configured GSM RSSI measurement compressed mode sequence. Accordin
finished in 1000 ms. According to 3GPP specifications, the number of inter-RAT neighboring cells should not exceed 32. There
The setting of this parameter has impact on the Uu signaling traffic. If the period is too short and the reporting frequency is too
Hysteresis for event 2D.
This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the currently used frequency is b
triggered in time. If this parameter is set to a smaller value, ping-pong reporting of event 2D is likely to occur.
The setting of this parameter should consider the radio conditions (slow fading), actual handover distance, and moving speed
Hysteresis for event 2F.

The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the probability of ping-po
The inter-RAT measurement hysteresis in periodical reporting mode is used to prevent the ping-pong reporting of event 2D (th
compressed mode and event 2F is used to disable the compressed mode. "Hystfor2D" can be increased slightly based on the
active set updates.
Hysteresis for event 3A.

The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the ability of resisting sig
another RAT where the UE needs to be handed over to must be of good quality. Therefore, the criteria for triggering the inter-R
The emulation result shows that in a cell where the average moving speed of UEs is high (for example, a cell that covers highw
this parameter can be set to a larger value 3.0 dB, because there are usually many tall buildings and thus the shadow fading v
Hysteresis for inter-RAT periodical reporting.

This parameter is used to avoid incorrect decisions caused by unexpected jitters of signals during inter-RAT handover decision
If this parameter is set to a greater value, the ability of resisting signal fluctuation improves and the number of ping-pong hand
of good quality. Therefore, the criteria for triggering the inter-RAT handover decision is hard to be fulfilled, and the call drop rat
Interval time between detection of event 2D and sending of the measurement report.
The emulation result shows that the hysteresis setting can effectively reduce the average number of handovers and the numb
the call drop rate is more sensitive to the delay, whereas, for the slow-moving UE, the call drop rate is less sensitive to the del
are in slow movement, this parameter can be set to a greater value. The value of this parameter can be adjusted according to
Interval time between detection of event 2F and sending of the measurement report.
Interval time between detection of event 3A and sending of the measurement report.
The value of this parameter is associated with the slow fading. If this parameter is set to a greater value, the probability of inco
signal change; however, the probability of incorrect decision becomes high.
The inter-frequency measurement reporting period is 480 ms. Therefore, the trigger delay time shorter than 480 ms is invalid.
If the parameter is set to a larger value, handover is unlikely to be triggered. However, call drops may increase as the paramet
Time delay for triggering handovers to GSM cells with non-verified BSIC.
During the period of time specified by this parameter, if the signal quality in a neighboring GSM cell fulfills inter-RAT handover
is set to a larger value, the average number of handovers decreases, but call drops may occur.
Time delay for triggering handovers to GSM cells with verified BSIC.
The criterion for triggering inter-RAT handover is as follows:
Mother_RAT + CIO >= Tother_RAT + H/2
If the quality of the neighboring GSM cell meets the preceding criterion, the RAN starts the trigger timer. After the timer expires
This parameter and the hysteresis are used together to prevent incorrect decisions caused by signal jitters during inter-RAT h
Considering that the UE is on the edge of the system, this parameter should be set to a comparatively low value. In situations
If this parameter is set to a larger value, the average number of handovers decreases, but call drops may occur.
Switch for verifying the Base Station Identity Code (BSIC).

This parameter is used to control cells where inter-RAT measurement reports are triggered. When the parameter is set to "RE
the BSIC of the measured cell is decoded correctly. This parameter is valid for both periodical reporting mode and event-trigge
If the parameter is set to "NOT_REQUIRED", handovers are likely to be triggered, but the handover reliability is lower than tha
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is Ec/No.
The threshold of triggering the inter-RAT measurement (the threshold of enabling the compressed mode) is a key parameter in
factors, moving speed of the UE and cell radius.
speeds. The emulation result shows that the call drop rate remains low for the UEs moving at a speed of 120 km/h when this p
If the cell is a macro cell, it indicates that micro cells exist in this cell. To enable the micro cells to handle more traffic, the comp
If the cell is a micro cell, the default value should be modified according to the link budgeting result.
Event 2D and event 2F are used to enable and disable the compressed mode respectively. When the cell is located in the cen
increase the threshold of triggering event 2D; otherwise, decrease the threshold of triggering event 2D. To prevent the frequen
Event 2D and event 2F are used to enable and disable the compressed mode respectively in inter-RAT measurement. The req
To enable the compressed mode earlier, increase the threshold of triggering event 2D; otherwise, decrease the threshold of tr
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Ec/No.
The threshold of stopping the inter-RAT measurement (the threshold of disabling the compressed mode) is a key parameter in
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the measurement quantity is Ec/No.
When Ec/No is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2D when the mea
In actual networks, set this parameter to -14 dB because the UEs in a cell usually move at different speeds. The emulation res
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Ec/No.
When Ec/No is used as the measurement quantity for PS domain HSPA services, the UE reports event 2F when the measure
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is Ec/No.
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is RSCP.
In most cases, users want to be maintained within a 3G network. Therefore, the start threshold of the inter-RAT measurement
the inter-RAT measurement start threshold should be set relatively larger in order to trigger inter-RAT measurement easily, thu
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is RSCP.
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the measurement quantity is RSCP.
When RSCP is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2D when the mea
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is RSCP.
Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the measurement quantity is RSCP.
When RSCP is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2F when the mea
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is RSCP.
Quality requirement for the cell of another RAT during inter-RAT handover for CS domain services.
For CS services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is used to set the cri
currently used frequency. If the value of "Inter-RAT Reporting Mode" is set to "PERIODICAL_REPORTING", this parameter is
If the value of "Inter-RAT Reporting Mode" is set to "PERIODICAL_REPORTING", this parameter is used for the assessment o
decision.
If the quality of the cell of another RAT in the inter-RAT measurement report fulfils the following criterion:
Then, the system starts the trigger timer, and makes the handover decision after the timer expires. If the quality of the cell of a
Mother_RAT + CIO < Tother_RAT - H/2
The RNC stops the timer and waits for another inter-RAT measurement report.
Here,
Mother_RAT is the measurement result of the GSM RSSI.
Tother_RAT is the inter-RAT handover decision threshold.
Cell Individual Offset (CIO) is the offset for the cell of another inter-RAT.
H represents the hysteresis, the setting of which can reduce wrong decisions caused by signal jitters.
The sensitivity of a GSM mobile phone is -102 dBm. Considering a margin of 3 dB for compensation of fast fading, 5 dB for co
The parameter value can vary with the handover policy. To have UEs handed over only to GSM cells of high quality, the inter-
Quality requirement for the cell of another RAT during inter-RAT handover for PS domain non-HSPA services.
For PS domain non-HSPA services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is
than the quality of the currently used frequency. If the value of "Inter-RAT Reporting Mode" is set to "PERIODICAL_REPORTI
decision.
Here,
Quality requirement for the cell of another RAT during inter-RAT handover for HSPA services.
For PS services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is used to set the cri
decision.
Here,
Ec/No quality threshold for used frequency of CS services.
For CS services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Repor
and the TargetRatCsThd criterion is fulfilled.
The following factors should be considered during setting:
When the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", the quality of the currently used frequency fulfills
Here,
QUsed is the estimated quality of the currently used frequency of UTRAN.
Tused is the quality threshold for the currently used frequency of GSM.
When the signal quality of the currently used frequency is poor, that is, below the specified value of this parameter, you can in
triggering threshold of event 2F, or is set equally to the triggering threshold of event 2D.
For combined services, the parameter configuration for CS services should be adopted as long as CS services are involved.
Impact on network performance:
If this parameter is set to a larger value, event 3A is likely to be triggered. However, handover is likely to be triggered when the
Ec/No quality threshold for used frequency of PS domain non-HSPA services.

For PS domain non-HSPA services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value o
than this threshold and the TargetRatR99PsThd criterion is fulfilled.
Here,
Ec/No quality threshold for used frequency of HSPA services.
For HSPA services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Rep
threshold and the TargetRatR99PsThd criterion is fulfilled.
Here,
RSCP quality threshold for used frequency of CS domain services.

For CS services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Repor
Here,
RSCP quality threshold for used frequency of PS domain non-HSPA services.
For PS domain non-HSPA services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value o
Here,
RSCP quality threshold for used frequency of HSPA services.

For HSPA services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Re
Here,
Length of the timer for inter-RAT measurement.

After inter-RAT measurement starts, if no inter-RAT handover is performed when this timer expires, the inter-RAT measureme
This parameter is designed to prevent that the UE being in compressed mode for a long time when the handover criteria are n
decreases.
Most inter-RAT handovers can be finished within 60s.
If the parameter is set to a smaller value, the UE cannot finish inter-RAT handover. If the parameter is set to a larger value, the
"InterRATMeasTime" that satisfies most UEs.
Length of the timer to avoid ping-pong handovers between 2G and 3G networks.

When a UE in the CS domain is handed over from a 2G network to a 3G network, the system increases the hysteresis used fo
3A report. The value 0 indicates that the system does not take measures to avoid ping-pong handover between 2G and 3G ne
Hysteresis to avoid ping-pong handover between 2G and 3G networks.
used for inter-RAT measurement. The value 0 indicates that the system does not take measures to avoid ping-pong handover
Interval between handover attempts for event 3A.

This parameter specifies the interval between handover attempts for event 3A. If this parameter is set to a smaller value, hand
however, cause the increase in the RNC load.
Maximum number of handover attempts after inter-RAT handover triggered by event 3A fails.
This parameter specifies the maximum number of handover re-attempts for event 3A when the measurement control is valid. I
reaching the value specified by this parameter, the RNC makes no further handover attempt to the target cell. If the compresse
Maximum number of inter-RAT handover failures allowed due to physical channel failure. When the number of inter-RAT hand
attempts.
For details about the physical channel failure, see 3GPP TS 25.331.
Duration of the penalty for inter-RAT handover failure due to physical channel failure. The UE is not allowed to make inter-RAT
Unique ID of a cell
increases.
another RAT where the UE needs to be handed over to must be of good quality. Therefore, the criterion for triggering the inter

If the value of "Inter-RAT Report Mode" is set to "PERIODICAL_REPORTING", this parameter is used for the assessment of in
decision.
If the quality of the cell of another RAT in the inter-RAT measurement report fulfills the following criterion:
Here,
decision.
Here,
Maximum number of inter-RAT handover attempts after the non-coverage-based handover failures. For each handover attemp

decreases.
This parameter specifies the threshold for 2G load of relocation target, in an inter-RAT handover in CS domain. When the GSM
the uplink or downlink normalized load carried in the relocation response message from the 2G system exceeds the value of th
This parameter specifies the threshold for 2G load of relocation target, in an inter-RAT handover in PS domain. When the GSM
This parameter specifies the interval between the handover re-attempts for event 3C. If this parameter is set to a smaller value
attempts, however, cause the increase in the RNC load.
Maximum number of handover re-attempts for event 3C.

This parameter specifies the maximum number of handover attempts for event 3C when the measurement control message is
After reaching the value specified by this parameter, the RNC makes no further handover attempt to the target cell. If the comp
attempts.
ID of an RNC
Unique ID of a cell
This parameter specifies the Layer 3 filter coefficient for the intra-frequency measurement.
According to 3GPP TS 25.331, the filtered measurement value is calculated using the following formula, where k represents th
Fn = (1 - a) * Fn - 1 + a * Mn
a = (1/2)(k/2)
Here, Fn: filtered measurement result
Fn - 1: previously filtered measurement result
Mn: latest received measurement result from physical layer
When a is set to 1, L3 filtering is not applied.
The input measurement value to L3 filter has been filtered by L1 filter, where the impact of fast fading is almost eliminated. In t
measurement value, and provide more reliable measurement result for event judgement.
Note that this parameter has great impact on the overall performance of the handover. Therefore, set this parameter with caut
Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies the reference measurement q
threshold, the measurement quantity should be set based on the reality of the cell. If the cell is located in the center of the cov
factor that affects signal quality is the distance between the cell and the base station. In this case, you are advised to set this p
Maximum number of reporting event 1A after the reporting mode is changed to periodical reporting. When the number of repor
Interval at which event 1A is reported after the reporting mode is changed to periodical reporting. Generally, event 1A is report
reported for "PeriodMRReportNumfor1A" times at the interval specified by this parameter. If the mode of reporting event 1A is
Maximum number of reporting event 1C after the reporting mode is changed to periodical reporting. When the number of repo
Interval at which event 1A is reported after the reporting mode is changed to periodical reporting. Generally, event 1C is report
reported for "PeriodMRReportNumfor1C" times at the interval specified by this parameter.If the mode of reporting event 1C is
Maximum number of reporting event 1J after the reporting mode is changed to periodical reporting. When the number of repor
Interval at which event 1J is reported after the reporting mode is changed to periodical reporting. Generally, event 1J is reporte
reported for "PeriodMRReportNumfor1J" times at the interval specified by this parameter.If the mode of reporting event 1J is s
Relative threshold for event 1A decision when VP service is performed. If this parameter is set to a greater value, the probabili
directly affect the SHO ratio. Therefore, the threshold should be wisely chosen to achieve smooth SHOs. The value of this par
threshold is set to 5 dB, the ratio of the UE involved in soft handover (the number of cells in the active set is at least 2) is abou
pong handover.
You can set different relative thresholds for event 1A and event 1B to reduce the ping-pong effect and change the soft handov
specific applications, if the ping-pong effect cannot be curbed by adjusting the hysteresis values for event 1A and event 1B, yo
set increases. In this case, more UEs are in soft handover status; however, more forward resources are occupied.If this param
Relative threshold for event 1A decision when non-VP service is performed in CS domain. If this parameter is set to a greater
threshold can directly affect the SHO ratio. Therefore, the threshold should be wisely chosen to achieve smooth SHOs.
The value of this parameter determines the SHO area and SHO ratio. In the CDMA system, the ratio of the UE involved in soft
is at least 2) is about 35%. you are advised to set the relative threshold to a great value (5 dB to 7 dB) during site deployment,
set increases. In this case, more UEs are in soft handover status; however, more forward resources are occupied. If this param
Relative threshold for event 1A decision when PS service is performed. If this parameter is set to a greater value, the probabili
pong handover.
Relative threshold for event 1B decision when VP service is performed. If this parameter is set to a smaller value, the probabil
pong handover.
Relative threshold for event 1B decision when non-VP service is performed in CS domain. If this parameter is set to a smaller
threshold can directly affect the SHO ratio. Therefore, the threshold should be wisely chosen to achieve smooth SHOs. The va
when the relative threshold is set to 5 dB, the ratio of the UE involved in soft handover (the number of cells in the active set is
to avoid the ping-pong handover.
Relative threshold for event 1B decision when PS service is performed. If this parameter is set to a smaller value, the probabil
pong handover.
Ec/No absolute threshold for event 1F in the SHO algorithm. This parameter must be set to the value that guarantees the qual
Event 1F refers to the event reported when an urgent blind handover is triggered. If event 1F is reported in a cell belonging to
measurements on the pilot strength and signal quality in the best cell of the cell where the UE is located. Generally, this functio
this parameter is set to a smaller value, the probability of triggering event 1F reduces. For details on the definition of event 1F,
actual scenarios, this parameter should be set according to the handover strategy and network coverage.
RSCP absolute threshold for event 1F in the SHO algorithm. This parameter must be set to the value that guarantees the qua
This parameter specifies the hysteretic value for event 1A. The value of this parameter is associated with the slow fading. If th
parameter, see 3GPP TS 25.331. Event 1A, as a key event, refers to the event triggered when a cell is added to the active set
the ratio of soft handovers (SHOs) may be affected. In addition, filter coefficient and interval time must be considered in setting
This parameter specifies the hysteretic value for event 1B. The value of this parameter is associated with the slow fading, and
parameter.
This parameter specifies the hysteretic value for event 1C. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1D. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1F. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1J. The value of this parameter is associated with the slow fading, and
parameter.
Used for calculating the relative threshold of the soft handover based on the measurement report of each cell in the active set.
parameter is set to 0, the general quality of the active set is the quality of the best cell. In this case, the relative threshold of so
when maximum ratio combining is performed in the downlink of all cells in the active set.
This parameter specifies the interval time between detection of event 1A and sending of the measurement report. The value o
The time-to-trigger mechanism is introduced for the following purposes:
- reducing the number of wrong event reports caused by burst signals,
- preventing the ping-pong handover,
- reducing the impact of shadow fading on event decisions.
Setting an appropriate triggering delay effectively reduces the average number of handovers and the number of wrong handov
If the handover cannot be triggered in time, the time-to-trigger parameter for event 1A needs to be changed to 200 ms or 100
This parameter specifies the interval time between detection of event 1B and sending of the measurement report. The value o
Setting an appropriate interval time effectively reduces the average number of handovers and the number of wrong handovers
This parameter specifies the interval time between detection of event 1C and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1D and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1F and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1J and sending of the measurement report. The value of
If events 1A, 1C, and 1D are reported to the RNC, the target cell can be added to the active set only when CPICH Ec/No is gre
This parameter is used to set a baseline for the quality of the radio links to be added. The current events of soft handovers are
more downlink resources are occupied and more TPC errors are caused, and the soft handover performance is worsened. Th
This parameter should be adjusted, based on the planned Ec/No that the cell soft handover area is expected to reach. If this p
the probability for adding a neighboring cell to the active set increases. In this case, however, the service quality of the cell to b
Maximum number of cells in an active set. This parameter is used to achieve the balance between the signal quality in the SH
several cells. This increases the amount of data to be processed and lowers the system performance. To reduce intra-frequen
decrease in cells in the active set can reduce the consumption of system resources.
Threshold of the quality of the cell reporting event 1F for triggering blind handover. The blind handover is triggered only when
This parameter is used to raise the success rate of blind handovers. If all the signals in the cell reporting event 1F are of poor
Pilot power adjustment step increased or decreased in each increase of the cell breathing algorithm or decrease of cell pilot. F
If the cell downlink load exceeds this threshold, the algorithm will decrease the pilot transmit power of the cell so as to increase
If the cell downlink load is lower than this threshold, the algorithm will increase the pilot transmit power of the cell so as to shar
If the ratio of UL load of the cell to the uplink capacity is not lower than this threshold, the UL load reshuffling function of the ce
threshold should be higher than 10%. The ping-pong effect of the preliminary congestion state may occur.
If the ratio of UL load of the cell to the uplink capacity is lower than this threshold, the UL load reshuffling function of the cell is
If the ratio of DL load of the cell to the downlink capacity is not lower than this threshold, the DL load reshuffling function of the
If the ratio of DL load of the cell to the downlink capacity is lower than this threshold, the DL load reshuffling function of the cel
If the ratio of UL load of the cell to the uplink capacity is not lower than this threshold, the UL overload and congestion control
difference between the OLC release threshold and the OLC trigger threshold is higher than 10%. It is desirable to set the two p
If the ratio of UL load of the cell to the uplink capacity is lower than this threshold, the UL overload and congestion control func
between the OLC release threshold and the OLC trigger threshold is higher than 10%. It is desirable to set the two parameters
If the ratio of DL load of the cell to the downlink capacity is not lower than this threshold, the DL overload and congestion contr
difference between the OLC release threshold and the OLC trigger threshold is higher than 10%. It is desirable to set the two p
If the ratio of DL load of the cell to the downlink capacity is lower than this threshold, the DL overload and congestion control fu
between the OLC release threshold and the OLC trigger threshold is higher than 10%. It is desirable to set the two parameters
If the DL load state of the cell is lasted longer than this threshold, the DL load state of the cell transfers.
HSUPA auto retransmit load trigger threshold.
HSUPA auto retransmit load release threshold.
UL load restricted trigger threshold ratio.If the state of the load for the TTI switchover algorithm is normal and the current uplin
UL load restricted release threshold ratio.If the state of the load for the TTI switchover algorithm is restricted and the current up
This parameter specifies the fairness threshold that is set between the R99 BE service and HSUPA service. When the ratio of
the HSUPA service rate.
NOACT: No load reshuffling action is taken.
INTERFREQLDHO: The inter-frequency load handover is performed.
BERATERED: Channels are reconfigured for the BE service.
QOSRENEGO: The renegotiation on the QoS of the uncontrollable real-time service is performed.
CSINTERRATSHOULDBELDHO: The inter-RAT SHOULDBE load handover of the CS domain is performed.
PSINTERRATSHOULDBELDHO: The inter-RAT SHOULDBE load handover of the PS domain is performed.
AMRRATERED (AMR service rate decreasing): The setting of the TFC subset and the negotiation of the service rate can be p
MBMSDECPOWER (MBMS power limiting): The MBMS service is configured with the minimum power.
CODEADJ (code tree reshuffling): The fragments of the downlink code tree are arranged.
PSINTERRATSHOULDNOTBELDHO: The inter-RAT SHOULDNOTBE load handover of the PS domain is performed.
PSINTERRATSHOULDNOTLDHO: The inter-RAT SHOULDNOTBE load handover of the PS domain is performed.
The LDR takes the actions in the preset sequence and judges whether each action is successful. If an action is unsuccessful,
Because each action is performed by its algorithm module, the LDR algorithm only selects users and delivers control message
The inter-frequency load handover has no impact on the QoS of users and can balance the cell load, so the inter-frequency lo
The BE service rate reduction is effective only when the DCCC algorithm is enabled.
This parameter has the same content as DlLdrFirstAction. The selected actions, however, should be unique.
Number of RABs selected in a DL LDR BE traffic rate reduction. In the actual system, this parameter can be set on the basis o
high value. Because the basic congestion control algorithm is designed to slowly decrease cell load, you need to set this param
Number of RABs selected in a DL LDR uncontrolled real-time traffic QoS renegotiation. The target subscribers of this paramet
may be smaller than the value of this parameter, for example, the candidate subscribers selected for downlink LDR do not me
Number of users selected in a DL LDR CS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a DL LDR PS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
low value. If the high-rate subscribers occupy a low proportion, set the parameter to a comparatively high value. Because the b
The mechanism of the LDR is that an action is performed in each [LDR period] and some services are selected based on the a
fluctuate greatly and over control may occur (the state of basic congestion turns into another extreme--under load). If the param
Number of users selected in a DL LDR CS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
Number of users selected in a DL LDR PS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
comparatively low value. If the high-rate subscribers occupy a low proportion, set the parameter to a comparatively high value

INTERFREQLDHO: The inter-frequency load handover is performed.
BERATERED: Channels are reconfigured for the BE service.
QOSRENEGO: The renegotiation on the QoS of the uncontrollable real-time service is performed.
CSINTERRATSHOULDBELDHO: The inter-RAT SHOULDBE load handover of the CS domain is performed.
CSINTERRATSHOULDNOTLDHO: The inter-RAT SHOULDBE load handover of the CS domain is performed.
The BE service rate decreasing is effective only when the DCCC algorithm is enabled.
This parameter has the same content as UlLdrFirstAction. The selected actions, however, should be unique.
Number of RABs selected in a UL LDR BE traffic rate reduction. In the actual system, this parameter can be set on the basis o
Number of RABs selected in a UL LDR uncontrolled real-time traffic QoS renegotiation. The target subscribers of this paramet
Number of users selected in a UL LDR CS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a UL LDR PS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a UL LDR CS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
Number of users selected in a UL LDR PS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
The inter-frequency neighboring cell could be selected as the destination of load handover only when its load remaining space
congestion status. The higher the parameter is, the more difficult it is for the inter-frequency blind handover occurs.
The inter-frequency neighboring cell could be selected as the destination of load handover only when its load remaining space
congestion status. The higher the parameter is, the more difficult it is for the inter-frequency blind handover occurs.
The UE can be selected to process load handover only when its bandwidth is less than this threshold.
The UE can be selected to process load handover only when its bandwidth is less than this threshold.
When the priority of the RAB of MBMS services exceeds this threshold, reconfigure the MBMS power to the minimum power. T
service must be decreased as required in the duration of cell congestion. Some services with high priority, for example the dis
failure and the load control algorithm.
This parameter specifies the Cell SF reserved threshold used for judging whether the code load reshuffling (LDR) is allowed. T
FALSE means not considering the code priority during the code reshuffling. TRUE means considering the code priority during
This parameter specifies the number of users selected in code reshuffling. Code reshuffling can be triggered only when the nu
should be set to a comparatively low value.
Reserved SF threshold in uplink credit LDR. The uplink credit LDR could be triggered only when the SF factor corresponding t
Reserved SF threshold in downlink credit LDR. The downlink credit LDR could be triggered only when the SF factor correspon
Code resource usage difference threshold. Inter-frequency handover is triggered when the difference of the resource usage of
This switch is valid only when the inter-frequency handover switch is enabled. TRUE means that inter-frequency handover is s
frequency coverage, if code resources present a bottleneck, such as indoor environment, the parameter is recommended to b
Indicates whether gold users involve in the switch of congestion control. According to the policy set for gold users by operators
cell resource congestion, which impacts user service quality. If the switch is disabled, no action is performed on gold users.
This parameter specifies the forbidden traffic classes when perform inter-frequency handover, in order to prevent disarranging
The threshold of the reserved SF is used for judging the uplink credit state for TTI switchover decision. When uplink credit is lo
This parameter specifies load handover method.When network is composed of same frequency band,Blind Handover method
Unique ID of a cell
Function control item switches:
1) INTELLIGENT_INTERFREQ_UE_TYPE_STEERING: When this switch is turned on, the Intelligent Inter-Carrier UE Layered
Unique ID of a cell
MBDR switch
This parameter is the relative threshold of cell for judging whether uplink MBDR algorithm of inter frequency is in overload stat
the product of uplink cell admission control threshold and this parameter, and is lower than the uplink cell admission control th
This parameter is the relative threshold of cell for judging whether downlink MBDR algorithm of inter frequency is in overload s
higher than the product of downlink cell admission control threshold and this parameter, and is lower than the downlink cell ad
Inter-frequency measurement report mode.

There are two inter-frequency handover report modes in the RNC, namely, event-triggered report and periodical report.
- Event-triggered measurement report
In this mode, event 2C is used to decide whether to trigger inter-frequency handover.
- Periodical report mode
When the quality of the inter-frequency cell reported by the UE meets the criteria for inter-frequency handover, the delay trigge
Measurement quantity used in measurement-based inter-frequency measurement in event (2C) triggered or periodical reportin
- CPICH: Common Pilot Channel
- Ec/No: Signal-to-Noise Ratio
- RSCP: Received Signal Code Power
- CPICH_Ec/No: to use the Ec/No measurement quantity for event 2C or Inter-Frequency periodical measurement. The physic
- CPICH_RSCP: to use the RSCP measurement quantity for event 2C or Inter-Frequency periodical measurement. The physic
- BOTH:both quantities of the target cell must be satisfied when performing the handover judgement.Valid when the Inter-Freq
triggered in time.

Threshold of signal quality of the target frequency for triggering inter-frequency(Ec/No) measurement.
If the mode is set to event mode, this parameter is used to set measurement control on the event 2C.
If the mode is set to periodical mode, this parameter is used to estimate the periodical reports and only if quality of the target fr
Threshold of signal quality of the target frequency for triggering inter-frequency(RSCP) measurement.
If the mode is set to event mode, this parameter is used to set measurement control on the event 2C.
If the mode is set to periodical mode, this parameter is used to estimate the periodical reports and only if quality of the target fr
The maximum number of attempts to perform inter-freq handovers

This parameter specifies the maximum number of attempts for the RNC to perform inter-freq handover after inter-freq handove
Timer length for inter-frequency measurement.
After inter-frequency measurement starts, if no inter-frequency handover is performed when this timer expires, the inter-freque
This parameter is used to prevent the long inter-frequency measurement state (compressed mode) due to unavailable measur
Unique ID of a cell
MBDR switch
This parameter is the relative threshold of cell for judging whether uplink MBDR algorithm of inter RAT is in overload state. It re
of uplink cell admission control threshold and this parameter, and is lower than the uplink cell admission control threshold, upli
This parameter is the relative threshold of cell for judging whether downlink MBDR algorithm of inter RAT is in overload state.
product of downlink cell admission control threshold and this parameter, and is lower than the downlink cell admission control
increases.
Inter-RAT measurement report mode.

-Event-triggered measurement report
In this mode, event 3C is used to decide whether to trigger inter-RAT handover.
-Periodical report mode

Quality requirement for the inter-RAT cell during an inter-RAT handover with CS domain services.
This parameter is used to set measurement control on the event 3C. The event 3C is triggered when the signal quality of the ta
If the periodical report mode is used, the inter-RAT handover decision thresholds are used for the assessment of inter-RAT co
If the quality of another RAT in the inter-RAT measurement report meets the following condition:
the system starts the trigger timer and implements the handover decision after timeout. If the quality of the preceding RAT mee
The system stops the timer, and the RNC waits for another inter-RAT measurement report.
In which,
Mother_RAT indicates the measurement result of the GSM RSSI;
Tother_RAT indicates the inter-RAT handover decision threshold;
Cell Individual Offset (CIO) indicates the offset of the inter-RAT cell;
H represents the hysteresis. Hysteresis can reduce wrong decisions caused by signal jitters.
The sensitivity of a GSM mobile phone is -102 dBm, so the outdoor reception level should not be lower than -90 dBm, conside
The values of inter-RAT handover decision thresholds vary with the handover policy. To have UEs hand over only to the GSM
This parameter specifies the maximum number of attempts for the RNC to perform inter-RAT handovers after a cell-oriented m
The ratio of the users which could launch the handover to inter-RAT neighbour cell.
When the parameter is ALL_USER, it means all of the users could be handover to the inter-RAT neighbour cell. When the par
the parameter is QUARTER, it means only 1/4 of the users could be handover to the inter-RAT neighbour cell.
Timer length for inter-RAT measurement.

After inter-RAT measurement starts, if no inter-RAT handover is performed when this timer times out, the inter-RAT measurem
To set this parameter, you need to consider the following factors:
This parameter aims to prevent that the handover conditions are not met and the compressed mode is kept for a long time wh
Most inter-RAT handovers can be finished within 60 s.
As for the impact on network performance,
If the InterRATMeasTime is excessively low, the UE cannot finish inter-RAT handovers. If the parameter is set to a great value
Strech for penalty of inter-RAT handover failure. No try of inter-RAT handover to the penalty cell will be taken until penalty finis
This parameter specifies the traffic class of the MBMS service carried on the common channel. For details of this parameter, r
This parameter specifies the rate of the MBMS service carried on the common channel. For details of this parameter, refer to t
This parameter specifies the maximum power of the FACH. For details of this parameter, refer to the 3GPP TS 25.211.
This parameter specifies the minimum coverage percentage of the MTCH corresponding to the RAB priority of 0. When the ce
minimum coverage area of the MBMS service. The minimum coverage area is set to a certain percentage of the coverage are
25.346.
This parameter specifies the minimum coverage percentage of the MTCH corresponding to the RAB priority of 15. When the c
25.346.
Start point of the arrival window of DL data frame. Normally, it is forecasted that a DL data frame will arrive after the time spec
End point of the arrival window of DL data frame. Normally, it is forecasted that a DL data frame will arrive before the time spe
This parameter specifies the transport mode of MBMS services. The point-to-multipoint (PTM), point-to-point (PTP), and enhan
complicated. In dynamic mode, transition between PTP and PTM modes is performed dynamically to balance the quality of se
MBMS service, and the MBMS user might experience service disruption when the user moves across the border between PTP
When the number of UEs responding to counting/recounting is greater than or equal to this threshold, the PTM mode is applie
This parameter specifies the NPTP-PTM offset. During recounting in PTP mode, if the number of PTP users is larger than or e
The transition between PTP and PTM affects user experience. Thus, to minimize ping-pong effect, the transition between PTP
Threshold" is small, it is recommended that the default value of this parameter be used.
MBMS SA ID. For detailed information of this parameter, refer to the 3GPP 25.346.
Physical channel ID of the MICH.
The value indicates whether the MICH uses time and space TX diversity. For detailed information of this parameter, refer to th
ID of the physical channel carrying the MCCH
ID of the transport channel carrying the MCCH
Switch of the FLC algorithm. The FLC is a mandatory algorithm used in the multi-frequency network to guarantee that UEs cam
Unique ID of a cell
When the measurement-based DRD is performed, this parameter is used to determine whether the DRD retry for blind handov
If this parameter is set to "ON", the DRD retry for blind handover is performed in aperiodic mode.
If this switch is set to "OFF", the DRD retry for blind handover is not performed in aperiodic mode.
Specifies the time length of the measurement-based DRD periodic retry timer. After the service is set up or the data reconfigur
periodic retry timer, initiate an inter-frequency measurement for the DRD inter-frequency neighboring cell, and initiate the chan
subscribers to re-access the cell with a high priority becomes low. If this parameter is set to a smaller value, the probability for
Interval between sending of periodic measurement reports.

This parameter has impact on the Uu signaling flow. If this parameter is set to a small value, the RNC may have high load whe
RSCP Threshold for the target cell. This parameter is used to estimate the signal quality of the periodic reports.The DRD is trig
attempt success rate is high. If this parameter is set to a lower value, it is easy for subscribers to re-access another cell with a
Ec/No Threshold for the target cell. This parameter is used to estimate the signal quality of the periodic reports. The DRD is tri
order to increase the successful rate of handover, inner protection mechanism keep Ec/No of target cell larger than -16.
Number of retry periods in the interval between a failure of a measurement-based DRD re-attempt and the initiation of the nex
with a high priority becomes high; however, the performance is greatly affected. Note: The process of a measurement-based D
retries the access to a cell in the reported DRD cell list. The process ends until the cell access succeeds.
Unique ID of a cell
This parameter defines the timer length for inter-frequency measurement.
The interval between two reports is the configured value.

This parameter has impact on the Uu signaling flow. If the interval is too short and the frequency is too high, the RNC may hav
Estimate the signal quality of the periodic reports. The inter-frequency handover is triggered only when the signal quality of the
Indicating whether the intra-frequency measurement control information should be delivered through the system information. G
system, the UE can start the intra-frequency measurement and send the measurement report immediately after it enters CELL
handover area to implement soft handovers more quickly to decrease the call drop rate. With the preconfiguration function, the
to the 3GPP TS 25.331 protocol.
Indicating whether the inter-frequency/RAT measurement control information should be delivered through the system informat
measurement and cell reselection assessment according to the inter-frequency neighboring cell list in the SIB11 or SIB12. If in
SIB12. If the inter-frequency FDD measurement indicator and Inter-RAT measurement indicator are set to FALSE in the syste
inter-RAT neighboring cell is configured, the UE does not perform the inter-frequency or inter-RAT measurement and cell rese
Whether the UE in the CELL_FACH state performs inter-frequency or inter-RAT measurement. When "InterFreqInterRatMeas
"InterFreqInterRatMeasInd" is set to INTER_FREQ_AND_INTER_RAT, this parameter can be set to NOT_REQUIRE, INTER_
ID of an RNC
ID of a neighboring cluster.
E-UTRA Absolute Radio Frequency Channel Number

This parameter specifies the absolute priority level of the E-UTRA frequency.
The UE compares the value of this parameter with the absolute priority level of the serving cell, and specifies the target freque
That is,
when the value of this parameter is greater than the priority level of the serving cell, the UE measures the neighboring frequen
When the value of this parameter is smaller than the priority level of the serving cell, the UE measures the neighboring frequen
The value of this parameter is set during network planning.
The greater the value of this parameter is, the easier the UE reselects a cell on this frequency, the smaller the value of this pa
For details on this parameter, see 3GPP TS 25.304.
This parameter specifies the RSRP above which the UE performs cell reselection from the serving cell to a cell on the target fr
The UE measures cells on the target frequency for cell reselection.
Within the interval defined by Treselections, if the RSRP of the cell on the target frequency is greater than the value of this par
The greater the value of this parameter is, the harder the UE reselects a cell on the target frequency, the smaller the value of t
This parameter specifies the RSRP above which the UE performs cell reselection from the serving cell to a cell on the target fr
The UE measures cells on the target frequency for cell reselection.
Within the interval defined by Treselections, if the RSCP of the serving cell is smaller than the parameter of RSCP threshold o
The greater the value of this parameter is, the harder the UE reselects a cell on the target frequency, the smaller the value of t
This parameter indicates the measurement bandwidth information common for all cells on the target frequency and is defined
The value of this parameter indicates the number of resource blocks over which the UE could measure.
In the E-UTRA system, the sign N is used to indicate the cell bandwidth.
The current protocol supports six types of bandwidth, namely, N = 6, 15, 25, 50, 75, and 100, mapping with 1.4 MHz, 3 MHz, 5
In the UTRA system, the cell bandwidth is 5 MHz.
This parameter indicates the minimum required RSRP of the cell on the target frequency.
During cell reselection decision, the Srxlev is obtained by the RSRP of the cell on the target frequency measured by the UE m
If the Srxlev is greater than the parameter of the target cell during the interval defined by Treselections, the UE performs cell re
The greater the value of this parameter is, the harder the UE reselects a cell on this frequency, the smaller the value of this pa
This parameter indicates the E-UTRA monitoring indication.

The value TRUE indicates that UEs in Idle mode can detect E-UTRA cells and report the result to the non-access stratum (NA
This parameter is used to set the number of cells in the blacklist of the target frequency.
Cells in the blacklist of the E-UTRA frequency are not used as target cells for cell reselection.
This parameter indicates physical cell ID of cell in the blacklist.

Cell in the blacklist is not used as target cell for cell reselection. Physical cell ID are used to distinguish cell in the specified fre













DL fast TF restriction refers to a situation where, when the cell is overloaded and congested, the downlink TF can be adjusted
The mechanism of the OLC is that an action is performed in each [OLC period] and some services are selected based on the
After the overload is triggered, the RNC immediately executes OLC by first executing fast TF restriction. The internal counter i
exceeds the OLC action threshold, the previous operation has no obvious effect on alleviating the overload and the system ha
overload status is released slowly.
UL fast TF restriction refers to a situation where, when the cell is overloaded and congested, the uplink TF can be adjusted to
After the overload is triggered, the RNC immediately executes OLC by first executing fast TF restriction. The internal counter i
exceeds the OLC action threshold, the previous operation has no obvious effect on alleviating the overload and the system ha
The lower the parameters are, the more likely the users are released, resulting in negative effect on the system performance.
Selection of RABs of the OLC is based on the service priorities and ARP values and bearing priority indication. The RAB of low
UlOlcFTFRstrctRabNum and DlOlcFTFRstrctRabNum to comparatively low values. If the high-rate subscribers occupy a low p
the cell load decreases, and the more user QoS is affected.
UL fast TF restriction refers to a situation where, when the cell is overloaded and congested, the uplink TF can be adjusted to
Selection of RABs of the OLC is based on the service priorities and ARP values and bearing priority indication. The RAB of low
UlOlcFTFRstrctRabNum and DlOlcFTFRstrctRabNum to comparatively low values. If the high-rate subscribers occupy a low p
The higher the parameters are, the more users are involved in fast TF restriction under the same conditions, the quicker the ce
The smaller this parameter is, the larger the TF restrict effect. The lower the parameter is, the more severe the rate is restricte
greater this parameter is, the larger the TF restrict effect.
RateRstrctTimerLen and RateRecoverTimerLen are effective only to the downlink. The uplink fast TF restriction is performed b
the time expires. The higher RateRstrctTimerLen is, the more slowly the BE service rate decreases. The lower RateRstrctTime
restriction. RateRstrctTimerLen and RateRecoverTimerLen are effective only to the downlink. The uplink fast TF restriction is p
restriction once the time expires. The higher RateRecoverTimerLen is, the more slowly the BE service rate recovers, while the
User release is an extreme method in reducing the cell load and recovering the system when the cell is overloaded and conge
For the users of a single service, the releasing of RABs means the complete releasing of the users. The releasing of RABs cau
User release is an extreme method in reducing the cell load and recovering the system when the cell is overloaded and conge
For the users of a single service, the releasing of RABs means the complete releasing of the users. The releasing of RABs cau
This parameter indicates whether the MBMS service is released first or user first when the overload occurs.
MBMS service release is an extreme method in reducing the cell load and recovering the system when the cell is overloaded a
Transfer Common Channel User number
Value range: 0~10
Content: When the system is overloaded and congested, users on the DCH can be reconfigured to the CCH in order to reduce
If the parameter value is too high, the OLC action may fluctuate greatly and over control may occur (the state of overload and
This parameter defines the reduce value in reducing FACH power Action.
It is used to decide whether the cell load level is "Light" or not. It is denoted by the ratio of NodeB TX power to the maximum T
If the load of a cell is equal to or lower than this threshold, the load level of this cell is light.
If the load level of a cell is light, the PUC algorithm will configure selection/reselection parameters for this cell to lead the UE to
It is used to decide whether the cell load level is "Heavy" or not. It is denoted by the ratio of NodeB TX power to the maximum
If the load of a cell is equal to or higher than this threshold, the load level of this cell is heavy.
If the load level of a cell is heavy, the PUC algorithm will configure selection/reselection parameters for this cell to lead the UE
Hysteresis used to determine the cell load level. It is denoted by the ratio of NodeB TX power to the maximum TX power. It is
Offset of Sintersearch when center cell load level is "Light" (Note: Sintersearch is used to decide whether to start the inter-freq
Offset of Sintersearch when center cell load level is "Heavy" (Note: Sintersearch is used to decide whether to start the inter-fre
Offset of Qoffset1 when neighboring cell load is lighter than that of the center cell (Note: Qoffset1 is used as a priority to decid
Offset of Qoffset2 when neighboring cell load is lighter than that of the center cell (Note: Qoffset2 is used as a priority to decid
Offset of Qoffset1 when neighboring cell load is heavier than that of the center cell (Note: Qoffset1 is used as a priority to deci
Offset of Qoffset2 when neighboring cell load is heavier than that of the center cell (Note: Qoffset2 is used as a priority to deci
Unique ID of a cell
Frequency hysteresis of downlink RSCP QoS.
This parameter controls the used frequency thresholds for the inter-frequency and inter-RAT measurement based on QoS.
In event mode, if the inter-frequency and inter-RAT measurement events occurred for the downlink QoS reason, the used freq
The larger the value of the parameter is, the more easily event 2B, inter-frequency handover based on QoS, and event 3A, int
Timer length for downlink QoS measurement.

This parameter controls the time lengths for the inter-frequency and inter-RAT measurement based on QoS.
After inter-frequency or inter-RAT measurement starts, if no inter-frequency handover is performed when this timer expires, the
For the inter-frequency or inter-RAT measurement based on coverage, the compressed mode can be stopped through reportin
It reduces the influence of long time compressed mode to the serving cell.
The compressed mode may be stopped ahead of time, which can cause the result that the UE fails to initiate inter-frequency o
Timer length for uplink QoS measurement.

This parameter controls the time lengths for the inter-frequency and inter-RAT measurement based on Qos.
This parameter configures the used frequency measurement quantity to trigger the inter-RAT measurement for the purpose of
Ec/No: signal-to-noise ratio
RSCP: received signal code power
CPICH_Ec/NO: the measurement quantity used for event 2D and 2F, with unit of dB
CPICH_RSCP: the measurement quantity used for event 2D and 2F, with unit of dBm
The RNC, in the coverage-based inter-RAT measurement, may configure that the inter-RAT measurement quantity are deliver
the QoS-based inter-RAT measurement to set the used frequency separately. When both the QoS-based and the coverage-ba
When the UE moves to the cell border, and there is a intra-frequency neighboring cell in the moving direction, CPCICH Ec/No
and the quality should be evaluated according to CPCICH RSCP. If the measurement quantity is not properly selected, the ha
Duration when the measured value of AMR keeps fulfilling the 6A1 measurement condition before the event 6A1 is triggered. E
lowered. The measured value is reported after it fulfills the conditions for reporting and for the trigger time specified by this par
Duration when the measured value of AMR keeps fulfilling the 6B1 measurement condition before the event 6B1 is triggered. E
raised. The measured value is reported after it fulfills the conditions for reporting and for the trigger time specified by this param
Duration when the measured value of AMR keeps fulfilling the 6D measurement condition before the event 6D is triggered. Ev
The measured value is reported after it fulfills the conditions for reporting and for the trigger time specified by this parameter. T
Duration when the measured value of VP keeps fulfilling the 6A1 measurement condition before the event 6A1 is triggered. Th
Duration when the measured value of VP keeps fulfilling the 6B1 measurement condition before the event 6B1 is triggered. Th
Duration when the measured value of VP keeps fulfilling the 6D measurement condition before the event 6D is triggered. The
Duration when the measured value of BE keeps fulfilling the 6A1 measurement condition before the event 6A1 is triggered. Th
Duration when the measured value of BE keeps fulfilling the 6B1 measurement condition before the event 6B1 is triggered. Th
Duration when the measured value of BE keeps fulfilling the 6D measurement condition before the event 6D is triggered. The
Smooth filtering coefficient for UL measured values. The smooth filtering algorithm is used to avoid random interference in me
Smooth filtering coefficient for DL measured values. The smooth filtering algorithm is used to avoid random interference in me
Duration from when the AMR TX power is beyond the threshold Ea or below the threshold Eb to when the event Ea or Eb is tri
This parameter specifies the reporting period of the event E of the AMR service. The unit of the reporting period can be 10 ms
This parameter is valid when the corresponding parameter related to the reporting period unit for the event E of AMR service i
Duration from when the VP TX power is beyond the threshold Ea or below the threshold Eb to when the event Ea or Eb is trigg
This parameter specifies the reporting period of the event E of the VP service. The unit of the reporting period can be 10 ms o
This parameter is valid when the corresponding parameter related to the reporting period unit for the event E of VP service is s
Duration from when the BE TX power is beyond the threshold Ea to when the event Ea is triggered or from when the BE TX po
This parameter specifies the reporting period of the event E of the BE service. The unit of the reporting period can be 10 ms o
This parameter is valid when the corresponding parameter related to the reporting period unit for the event E of BE service is s
Duration within which the measured power being lower than the threshold is allowed for BE service. This parameter is used to
This parameter specifies the reporting period of the event F of the BE service. The unit of the reporting period can be 10 ms o
This parameter is valid when the corresponding parameter related to the reporting period unit for the event F of BE service is s
Unique ID of a cell
Traffic class whose RRC redirection parameters are to be set

Whether the RRC redirection algorithm is valid for the specified service. The algorithm is valid only when the RRC direct redire
- OFF indicates that RRC redirection is not allowed.
- Only_To_Inter_Frequency indicates that only RRC redirection to inter-frequency cells is allowed.
- Only_To_Inter_Frequency indicates that only RRC redirection to inter-RAT cells is allowed.
Possibility of redirecting the UE to another cell. When the load of the serving cell is within the normal range, a UE may be redir
Possibility of redirecting the UE to another cell. When the UL load state or DL load state of the serving cell is LDR or OLC, a U
BAND4
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
Value range: 0-16383
Identifying the type of a CN.
This parameter denotes the rate of services. The typical services include 12.2 kbit/s, 64 kbit/s, 144 kbit/s, 384 kbit/s and so on
This parameter specifies the maximum DL RL power to be assigned.

This parameter should fulfill the coverage requirement of the network planning, and the value is relative to [PCPICH transmit p
This parameter specifies the minimum DL RL power to be assigned.

This parameter should consider the maximum downlink transmit power and the dynamic range of power control, and the value
3GPP TS 25.433.
This parameter refers to the downlink spreading factor used by the RL carrying single service with the CN domain in typical en
detailed information of this parameter, refer to 3GPP TS 25.433.
Measurement quantity of cell selection and reselection. It can be set to CPICH Ec/N0 or CPICH RSCP. For detailed informatio
The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for cell selection and reselection is
According to the R regulation, the current serving cell involves in cell selection after the measurement value is added with the
frequent location updates (idle mode), URA updates (URA_PCH), or cell updates (CELL_FACH, CELL_PCH), and thus increa
According to the CPICH RSCP emulation report of inter-frequency hard handovers, the measurement hysteresis ranges 4 dBm
example the suburbs and countryside, reduce the measurement hysteresis to guarantee timely location updates of UEs. The h
The hysteresis value of the serving FDD cells in connected mode in case the quality measurement for cell selection and resele
The hysteresis value of the serving FDD cells in idle mode in case the quality measurement for cell selection and reselection is
be adopted as the value. This parameter is not configured when its value is 255.
The hysteresis value of the serving FDD cells in connected mode in case the quality measurement for cell selection and resele
is 255.
If the signal quality (CPICH Ec/No measured by the UE) of a neighboring cell is better than that of the serving cell during the s
Set the parameter as follows:
1. Ensure that the UE can reselect a cell when crossing the non-soft-switch area of the cell and that the UE timely performs loc
2. Ensure that the UE does not reselect a cell when it is in the soft-switch area of the cell. In this way, the unnecessary location
3. Consider the difference between cells that cover different areas, for example the cells covering highways and cells covering
the parameter is set to a comparatively high value, the cell reselection delay may become excessively high, and thus cell rese
For detailed information, refer to 3GPP TS 25.304.
The minimum required quality threshold corresponding to CPICH Ec/No. The UE can camp on the cell only when the measure
cell, but it is possible that the UE cannot receive the system messages that are sent through the PCCPCH. For detailed inform
The minimum required RX threshold corresponding to CPICH RSCP. The UE can camp on the cell only when the measured C
the easier it is for the UE to reside in the cell, but it is possible that the UE cannot receive the system messages that are sent t
Indicating whether the actual value of Qrxlevmin should be added with the value of DeltaQrxlevmin or not. If QrxlevminExtSup
Actual minimum required RX level = minimum required RX level + extended minimum required RX level. For details, refer to th
The maximum allowed uplink transmit power of a UE in the cell, which is related to the network planning. For detailed informat
Threshold for intra-frequency cell reselection in idle mode. When the quality (CPICH Ec/No measured by the UE) of the servin
has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection
frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a
detailed information, refer to 3GPP TS 25.304.
Threshold for inter-frequency cell reselection in idle mode. When the quality (CPICH Ec/No measured by UE) of the serving ce
priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection start
start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a compara
information, refer to 3GPP TS 25.304.
Threshold for intra-frequency cell reselection in connected mode. When the quality (CPICH Ec/No measured by the UE) of the
reselection has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cel
UE may frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold
For detailed information, refer to 3GPP TS 25.304.
Threshold for inter-frequency cell reselection in connected mode. When the quality (CPICH Ec/No measured by UE) of the ser
has a priority higher than the inter-frequency cell reselection and inter-RAT cell reselection, the intra-frequency cell reselection
frequently start cell reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to a
detailed information, refer to 3GPP TS 25.304.
Threshold for inter-RAT cell reselection. When the quality (CPICH Ec/No measured by UE) of the serving cell is lower than this
value of this parameter is 127. The intra-frequency cell reselection has a priority higher than the inter-frequency cell reselectio
information, refer to 3GPP TS 25.304.
For a high-mobility UE, multiples this parameter by its reselection delay to reduce the reselection delay of the UE. This parame
This parameter is used to increase time of inter-frequency reselection. It is not configured when its value is 255. For detailed in
This parameter is used to increase time of inter-RAT reselection. It is not configured when its value is 255. For detailed inform
Indicating whether the non-HCS speed estimation parameter should be configured.
Maximum duration of non-HCS cell reselection. If the number of cell reselection exceed the value of this parameter during Tcr
Maximum number of non-HCS cell reselection. This parameter, along with Tcrmaxnonhcs, defines the speed estimation thresh
Hysteresis time before non-HCS resuming slow movement. When UE is in high-speed movement, if the number of cell reselec
This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement hysteresis of the UE is 1. It
Otherwise, the greater the parameter value is, the harder the cell selection happens. For detailed information, refer to 3GPP T
This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis of the UE is 1. It is used whe
This parameter indicates that in the CELL_PCH or URA_PCH connection mode, the measurement hysteresis of the UE is 2. It
This parameter indicates that in the CELL_FACH connection mode, the measurement hysteresis of the UE is 2. It is used whe
This parameter indicates the UE reselection delay in the CELL_PCH or URA_PCH connection mode. This parameter is not co
This parameter indicates the UE reselection delay in the CELL_FACH connection mode. This parameter is not configured whe
This parameter indicates the absolute priority level of the serving cell when the UE performs cell reselection.
The UE compares the absolute priority level of the serving cell with that of neighboring frequencies, and specifies the target fre
That is,
when the priority level of the serving cell is smaller than that of the neighboring frequency, the UE measures the neighboring fr
When the priority level of the serving cell is greater than that of the neighboring frequency, the UE measures the neighboring f
The greater the absolute priority level of the serving cell is, the harder the UE performs cell reselection, the smaller the absolu
This parameter specifies the minimum CPICH RSCP value that triggers the UE to measure cells on low-priority frequencies.
That is, subtract the minimum CPICH RSCP from the CPICH RSCP of the serving cell. If the obtained number is no greater th
The greater the value of this parameter is, the easier the UE measures cells for priority-based cell reselection, the smaller the
This parameter specifies the minimum CPICH Ec/No value that triggers the UE to measure cells on low-priority frequencies.
That is, subtract the minimum CPICH Ec/No from the CPICH Ec/No value of the serving cell. If the obtained number is no grea
The greater the value of this parameter is, the easier the UE measures cells for priority-based cell reselection, the smaller the
This parameter specifies the CPICH RSCP value of the serving cell below which the UE initiates cell reselection to a cell on th
The UE measures cells on the target frequency for cell reselection. Within the interval defined by Treselections, if the CPICH R
The greater the value of this parameter is, the easier the UE performs priority-based cell reselection, the smaller the value of t
Determine whether some system information blocks are broadcast in this cell. If the corresponding system information block is
Unique ID of a cell
This parameter specifies the type of measurement result that a UE needs to carry in an event-triggered or periodical measurem
to report measurement results of both the types: Reference Signal Received Power (RSRP) and Reference Signal Receiving Q
This parameter specifies the layer 3 filter coefficient for the LTE measurement. Layer 3 filter coefficient is sent to the UE and th
The variables in the formula are defined as follows: a=1/(2^(k/2)), where k is this parameter. Fn-1 is the old filtered measureme
This parameter specifies the duration of the timer that is used in LTE measurement. If the LTE measurement timer reaches the
parameter is set to 0, it indicates that the LTE measurement timer is not started.
This parameter specifies the measurement quantity of a handover target LTE system in an event 3C measurement report sent
Measurement", as is specified in 3GPP TS 25.331.
RSRP is the average power of signals received on all resource elements (REs) that carry reference signals within a certain sym
RSRQ is defined as the ratio of RSRP to RSSI (RSRQ = N*RSRP/RSSI). The coefficient N is introduced to adjust possible ban
This parameter specifies the hysteresis for a UE to report event 3C. For detailed description of the parameter, see 3GPP TS 2
This parameter specifies the interval time between detection of event 3C and sending of the measurement report. How to set t
This parameter specifies the RSRP threshold in the event 3C measurement of LTE during a handover that is not based on cov
25.331.
This parameter specifies the RSRQ threshold in the event 3C measurement of LTE during a handover that is not based on cov
25.331.
RTWP heavy threshold for the load balancing algorithm based on Received Total Wideband Power (RTWP). If power in a cell
RTWP light threshold for the load balancing algorithm based on RTWP. If power in a cell is less than the threshold, CPICH po
Pace at which CPICH power is increased or decreased each time
Identity of the UTRAN registration area. The URA is only used by the UTRAN and the CN does not know the URA. The URA c
This parameter specifies the index of the operator.
This parameter specifies the flow threshold at which G-CDRs are generated.
This parameter specifies the maximum number of charging condition changes. G-CDRs can be generated when the maximum
This parameter specifies the time threshold at which G-CDRs are generated.
This parameter is saved for the coming usage.
Difference between the transmit power of PICH and that of PCPICH. For details, refer to the 3GPP TS 25.433 protocol.
This parameter specifies the power offset between the transmit power of an AICH and that of P-CPICH. For details, refer to th
Switch for controlling the output of normal or abnormal flow information block.
Switch for deciding the output of information about the CS or PS domain.
Switch for controlling whether a flow information block is outputted.
Cause of RRC connection establishment that triggers the output of a CHR log.
Method of setting a CHR.

Number of the slot
Number of the subsystem
NodeB ID.
Whether the CHR function is supported in a specified scope. If the parameter is set to ON, the CHR function is enabled.
Indicating whether to use changing cell id in UU interface.
Indicate the period of cell ID changing.

In order that the UE and NodeB can start CM simultaneously, the user should predetermine the time difference between Comp
transmission from RNC to UE and that from RNC to NodeB. Usually it ranges 500 to 1500 ms. The radio frame length in WCD
Downlink compressed mode (CM) implementation mode selection threshold.
When the downlink spreading factor is greater than or equal to the value of this parameter, the SF/2 mode is preferred. Otherw
Uplink CM implementation mode selection threshold.
When the uplink spreading factor is greater than or equal to the value of this parameter, the SF/2 mode is preferred. Otherwise
CM type of the cell.

The CM parameters are configured on the basis of the CM type of the cell. That is, the CM sequence number is determined af
Whether the CM is limited by the downlink spreading factor (SF). Starting the compressed mode is resource consuming for the
downlink DCH channel; when this parameter is set to TRUE, the enabling of CM considers the SF of the downlink DCH chann
Downlink SF threshold for enabling compressed mode (CM).

When the parameter "DlSFLimitCMInd" is set to TRUE and the current downlink SF is smaller than or equal to the value of this
parameter, the active set quality measurement is allowed, that is, the CM can be enabled.
Whether the compressed mode (CM) can coexist with the HSDPA service. If this parameter is set to TRUE: 1. the RNC can en
DCH) channel switch. 2. The HSDPA services cannot be enabled when the CM is enabled.
This switch is used for the compatibility of the HSDPA terminals that do not support CM when HSDPA is enabled.
Whether the compressed mode (CM) can coexist with the HSUPA service. If this parameter is set to Permit: 1. the RNC can e
channel switch. 2. The HSUPA services cannot be enabled when the CM is enabled. If this parameter is set to BasedonUECa
This switch is used for the compatibility of the HSUPA terminals that do not support CM when HSUPA is enabled.
Whether the compressed mode (CM) can coexist with the HSPA+ service.
If this parameter is set to TRUE: 1. the RNC can enable the CM for HSPA+ services. 2. The HSPA+ services can be enabled w
enabled when the CM is enabled.
This switch is used for the compatibility of the HSPA+ terminals that do not support CM when HSPA+ is enabled.
Periodical location update is implemented by MS through the location update procedure. 0: The periodical update procedure is
Indicating whether attach/detach is allowed. NOT_ALLOWED indicates that MS cannot apply the IMSI attach/detach procedur
This parameter should be set according to the actual network situation . If there is the Gs interface between SGSN and MSC/V
CN domain specific Discontinuous Reception (DRX) cycle length coefficient broadcast on SIB1 and used by UEs in Idle Mode
Identifying a CN Node.
DSP index. This parameter uniquely identifies a peer DSP.
Protocol version supported by the CN.
CR supported by the protocol version of the CN.
Status of a CN node. The status needs to be negotiated with the CN and is configured through the MML command. A CN nod
1. Normal: This value indicates that the UE can access the CN node normally.
2. Offload: If the UE carries "NullNRI"("SET UOPERATORCFGPARA") in the Initial Direct transfer message, the UE cannot ac
3. Inhibited: This value indicates that the UE cannot access the CN node normally.
Capacity of a CN node. This parameter indicates the proportion of different CN nodes in the total capacity rather than the actu
The transfers bearer type of Iu interface.
This parameter is valid only when "CNDomainId" is set to CS_DOMAIN and "TnlBearerType" is set to IP_TRANS. When RTCP
Analyze the performance statistic of the above objects, overall evaluation the situation of the network.
The rate of RTCP bandwidth by the Iu CS bandwidth. For example if this value is 1, it expresses that the allocated RTCP path
This parameter is valid only when "CNDomainId" is set to CS_DOMAIN. When the parameter is set to ON, the RNC supports t
This parameter specifies whether to enable the end-to-end QoS assurance algorithm.
ON: The end-to-end (RNC and the CN) QoS assurance algorithm is enabled. In this case, the RNC obtains the service type in
OFF: The end-to-end (RNC and the CN) QoS assurance algorithm is disabled. In this case, the IEs that indicate service type i
This parameter specifies the blocked domain type.

This parameter specifies the processing duration of the cell blocking in the RNC.
Identify Operator Type,as follows:
Primary operator: Each RAN system has only one primary operator. The primary operator owns all or part of the resources of t
Secondary operator: Each RAN system can have a maximum of three secondary operators. A secondary operator owns part o
Outer Operator: In order to support mobility between two RNCs, we define the operator switched over to the target RNC as an
Common operator: PLMN-id indicated in the system broadcast information as defined for conventional networks, which non-su
Cn Operator Name.
Mobile country code. This parameter identifies the country where a mobile subscriber is located, for example, the Chinese MC
Mobile network code. This parameter identifies the public land mobile network (PLMN) to which a mobile subscriber belongs.
Represent an index for a CN operator. If " peratorType" is set to PRIM, the value range of "Operator Index" is 0-3. If "Operator
If "OperatorType" is set to COMM, the value range of "Operator Index" is 5-31.
Cn Operator Group Name.
Identify Operator Number in Operator Group.
Represent an index for a CN operator 1.

Represent an index for a Common Operator.
Counter check switch.
Count-C checking values.

For the PS BE service at a rate of 0 kbit/s, this parameter is used for the rate upsizing for DCCC triggered by event 4A. Unsuc
the length is set to 0, the timer is not started.
This parameter specifies the value of the channel retry timer. The timer will start when traffic is set up or reconfigured and som
This parameter specifies the value of the channel retry handover timer.
When handover is performed and some higher HSPA or HSPA plus technique is supported, UTRAN will trigger the reconfigura
Pingpang will happen when the reconfiguration is triggered immediately when handover succeeds, because handover procedu
In order to avoid the pingpang, this timer will start after handover procedure is performed, and the reconfiguration will not be tr
The timer is started when the RNC initiates the RAB Modify procedure. If RAB Modify message is received from the CN when
Period after which the retransmission type of UEs can be adjusted. In the HSUPA adaptive retransmission algorithm, this time
retransmission. Large retransmission means that the number of retransmissions is large . Small retransmission means that the
T302 is started after the UE transmits the CELL UPDATE/URA UPDATE message and stopped after the UE receives the CEL
default value is 4000.
Maximum number of retransmissions of CELL UPDATE/URA UPDATE.Protocol default value is 3.

T304 is started after the UE sends the UE CAPABILITY INFORMATION message and stopped after the UE receives the UE C
Protocol default value is 2000.
Maximum number of retransmissions of UE CAPABILITY INFORMATION. Protocol default value is 2.

T305 is started after the UE receives CELL UPDATE CONFIRM/URA UPDATE CONFIRM in CELL_FACH, URA_PCH or CEL
Protocol default value is 30. "Infinity" means the cell will not be updated.
T307 is started after T305 has expired and the UE detects "out of service area". It is stopped after the UE detects "in service a
T308 is started after the UE transmits RRC CONNECTION RELEASE COMPLETE. This message will be sent upon the expiry
Maximum number of retransmission of RRC CONNECTION RELEASE COMPLETE.
T309 is started after the UE is reselected to a cell belonging to another radio access system in connected mode, or the CELL
T312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive N312 "in sync" indications from
Maximum number of successive "in sync" indications received from L1.
T313 is started after the UE detects consecutive N313 "out of sync" indications from L1. T313 is stopped after the UE detects
Maximum number of successive "out of sync" indications received from L1. Protocol default value is 20.
T314 is started when the criteria for radio link failure are fulfilled and only radio bearers (RBs) associated with T314 exist.T314
In case of the RL failure when the UE is in CELL_DCH state, If the RL cannot be successfully reconfigured by CELL UPDATE
the expiry of T314, the corresponding service RBs will be removed.
T315 is started when the criteria for radio link failure are fulfilled, and only the radio bearer associated with T315 exists.T315 is
In case of the RL failure when the UE is in CELL_DCH state, T315 (or T314) is started and CELL UPDATE is sent. If the RL c
T315 should be set greater than T302*N302. In case of the expiry of T315, the corresponding service RBs will be removed.
Maximum number of successive "in sync" indications received from L1 when T313 is activated. Protocol default value is 1.
T316 is started after the UE detects "out of service area" in URA_PCH or CELL_PCH state.T316 is stopped after the UE detec
procedure when the UE detects "in service area". Protocol default value is 30.
T381 is started after the RNC send message "RRC CONNECTION SETUP"(or "CELL UPDATE CONFIRM"). If T381 expire an
CONFIRM") and restart timer T381 and increase V381. If RNC receive "RRC CONNECTION SETUP COMPLETE"(or the resp
Maximum number of resend times of message "RRC CONNECTION SETUP" or "CELL UPDATE CONFIRM". default value is
If the UE checks that no PS/CS data is transmitted, the UE will send the SIGNALLING CONNECTION RELEASE INDICATION
with the IE "Signalling Connection Release Indication Cause" set to "UE Requested PS Data session end" whilst timer T323 is
Channel configuration strategy switch group.

1) CFG_DL_BLIND_DETECTION_SWITCH: When the switch is on, the DL blind transport format detection function is used fo
2) CFG_HSDPA_64QAM_SWITCH: When the switch is on, 64QAM can be configured for the HSDPA service.
3) CFG_HSDPA_DC_SWITCH: When the switch is on, DC can be configured for the HSDPA service.
4) CFG_HSDPA_MIMO_SWITCH: When the switch is on, MIMO can be configured for the HSDPA service.
5) CFG_HSDPA_MIMO_WITH_64QAM_SWITCH: When the switch is on and the switches for 64QAM and MIMO are on, 64Q
6) CFG_HSPA_DTX_DRX_SWITCH: When the switch is on, DTX_DRX can be configured for the HSPA service.
7) CFG_HSPA_HSSCCH_LESS_OP_SWITCH: When the switch is on, HS-SCCH Less Operation can be configured for the H
8) CFG_HSUPA_16QAM_SWITCH: When the switch is on, 16QAM can be configured for the HSUPA service.
9) CFG_IMS_SUPPORT_SWITCH: When the switch is on and the IMS license is activated, the RNC supports IMS signaling.
10) CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH: When the switch is on, DL lossless RLC PDU size change is suppor
11) CFG_LOSSLESS_RELOC_CFG_SWITCH: When the switch is on and the UE supports lossless relocation, the RNC conf
12) CFG_MULTI_RAB_SWITCH: When the switch is on, the RNC supports multi-RABs combinations such as 2CS, 2CS+1PS
13) CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH: When the switch is on and the PDCP header compression license is a
14) CFG_PDCP_RFC2507_HC_SWITCH: When the switch is on and the PDCP IPHC license is activated, the PDCP IPHC he
15) CFG_PDCP_RFC3095_HC_SWITCH: When the switch is on and the PDCP ROHC license is activated, the PDCP ROHC
16) CFG_PTT_SWITCH: When this switch is on, the RNC identifies the PTT user based on the QoS attributes in the RAB ass
17) CFG_RAB_REL_RMV_HSPAPLUS_SWITCH: When this switch is on and if an RAB release is performed, the RNC decide
required in the initial bearer policy of the remaining traffic, the RNC falls back the feature to save the transmission resources. T
18) CFG_EDPCCH_BOOSTING_SWITCH: When the switch is on, Boosting can be configured for the HSUPA service.
19) CFG_HSDPA_DCMIMO_SWITCH: When this switch is turned on, DC+MIMO can be configured for the HSDPA service.
20) CFG_FREE_USER_SWITCH: When this switch is turned on, special handling for free access user is enabled.
21) CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH: When this switch is turned on, the RNC determines whether to enable th
Dynamic resource allocation switch group.
1) DRA_AQM_SWITCH: When the switch is on, the active queue management algorithm is used for the RNC.
2) DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm for admis
3) DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm is suppor
4) DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm for covera
5) DRA_BASE_COVER_BE_TTI_RECFG_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm is supporte
6) DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm for differentia
7) DRA_BASE_RES_BE_TTI_RECFG_SWITCH: When the switch is on, the TTI dynamic adjustment algorithm is supported fo
8) DRA_DCCC_SWITCH: When the switch is on, the dynamic channel reconfiguration control algorithm is used for the RNC.
9) DRA_HSDPA_DL_FLOW_CONTROL_SWITCH: When the switch is on, flow control is enabled for HSDPA services in AM m
10) DRA_HSDPA_STATE_TRANS_SWITCH: When the switch is on, the status of the UE RRC that carrying HSDPA services
DSCH, the switch PS_NON_BE_STATE_TRANS_SWITCH should be on simultaneously.
11) DRA_HSUPA_DCCC_SWITCH: When the switch is on, the DCCC algorithm is used for HSUPA. The DCCC switch must b
12) DRA_HSUPA_STATE_TRANS_SWITCH: When the switch is on, the status of the UE RRC that carrying HSUPA services
the switch PS_NON_BE_STATE_TRANS_SWITCH should be on simultaneously.
13) DRA_IP_SERVICE_QOS_SWITCH: Switch of the algorithm for increasing the quality of subscribed services. When this pa
14) DRA_PS_BE_STATE_TRANS_SWITCH: When the switch is on, UE RRC status transition (CELL_FACH/CELL_PCH/URA
15) DRA_PS_NON_BE_STATE_TRANS_SWITCH: When the switch is on, the status of the UE RRC that carrying real-time se
16) DRA_R99_DL_FLOW_CONTROL_SWITCH: Under a poor radio environment, the QoS of high speed services drops cons
R99 downlink flow control function is enabled.
17) DRA_THROUGHPUT_DCCC_SWITCH: When the switch is on, the DCCC based on traffic statistics is supported over the
18) DRA_VOICE_SAVE_CE_SWITCH: when the switch is on, the TTI selection based on the voice service type (including Vo
19) DRA_VOICE_TTI_RECFG_SWITCH: when the switch is on, the TTI adjustment based on the voice service type (including
CS algorithm switch group.
1) CS_AMRC_SWITCH: When the switch is on and the AMRC license is activated, the AMR control function is enabled for AM
2) CS_HANDOVER_TO_UTRAN_DEFAULT_CFG_SWITCH: When the switch is on, the default configurations of signaling an
and PhyCH, which are in the HANDOVER TO UTRAN COMMAND message is used.
3) CS_IUUP_V2_SUPPORT_SWITCH: When the switch is on and the "Support IUUP Version 2" license is activated, the RNC
Power control switch group.

1) PC_CFG_ED_POWER_INTERPOLATION_SWITCH: When the switch is on, E-DPDCH power interpolation formula is allow
extrapolation formula is also used. the interpolation formular is used for high-speed services, whereas the extrapolation formul
2) PC_DL_INNER_LOOP_PC_ACTIVE_SWITCH: When the switch is on, the status of inner loop DL power control is set to "A
3) PC_DOWNLINK_POWER_BALANCE_SWITCH: When the switch is on, the RNC supports DL power balancing. During sof
4) PC_EFACH_ECN0_DYN_ADJ_SWITCH: When the switch is on, the target value of Ec/N0 can be dynamically reconfigured
5) PC_FP_MULTI_RLS_IND_SWITCH: When the switch is on, the RNC informs the NodeB of the current RLS number throug
6) PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH: When the switch is on, the HSUPA Coverage Improvement Under Limit
7) PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH: When the switch is on, the Power Offset Adaptive Adjustment on
8) PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITCH: When the switch is on, the HSUPA service can use the smaller target
9) PC_INNER_LOOP_LMTED_PWR_INC_SWITCH: When the switch is on, the limited power increase function is used for DL
10) PC_OLPC_SWITCH: When the switch is on, the RNC updates the UL SIR TARGET of radio links on the NodeB side throu
11) PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH: When the switch is not on, a new initial SIRTarget value, during radio
switch is only valid when the OLPC switch is ON.
12) PC_SIG_DCH_OLPC_SWITCH: When the switch is on, SIG DCH is involved in UL OLPC as service DCH is. If the curren
13) PC_UL_SIRERR_HIGH_REL_UE_SWITCH: When the switch is on, the UE is unconditionally released if the SIR error is h
Compatibility switch group.
1) CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH: When the switch is on, the IMS signaling assigned by the CN undergoe
2) CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH: When the Iu QoS Negotiation function is active and the switch is o
less rate as Iu QoS negotiation rate.
3) CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH: When the switch is on, the IUUP version can be rolled back to R99 wh
4) CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH: When the switch is on, H2D is performed before a neighboring RNC
DL services cannot be mapped on the HS-DSCH. If the DRNC is of a version earlier than R6, DL services cannot be mapped
5) CMP_IUR_SHO_DIVCTRL_SWITCH: When the switch is on, the diversity combination over the Iur interface is configured o
MUST (for BE services) or MAY (for other services).
6) CMP_UU_ADJACENT_FREQ_CM_SWITCH: when the switch is on, the RNC initiates the inter-frequency measurement wi
within 5 MHz higher or lower than the current frequency; when the switch is off, the RNC activates the compressed mode befo
7) CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH: When the switch is on, When SRB is set up on DCH, and RNC decides t
8) CMP_UU_AMR_SID_MUST_CFG_SWITCH: For narrowband AMR services, when the switch is on, the SID frame is alway
9) CMP_UU_FDPCH_COMPAT_SWITCH: When the switch is OFF, if the information element that indicates the F-DPCH capa
is ON, if the information element that indicates the F-DPCH capability of UE exists in the message "RRC_CONNECT_REQ" o
UE supports HS-PDSCH.
10) CMP_UU_IGNORE_UE_RLC_CAP_SWITCH: When the switch is on, the RAB assignment request and the subsequent R
rejected.
11) CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH: When this switch is on, the cell individual offset (CIO) of the be
messages.
12) CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH: When the switch is on, the cell synchronization information trace
13) CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH: When the switch is on, the active set update is in the same procedu
aboveUEs.
14) CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH: When the switch is on, channel transition is in the same proced
15) CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH: By default, the switch is on. In this case, the Alternative E-bit is
16) CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH: When the switch is set to ON, only uplink RLC or downlink RLC can be r
17) CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH: When the switch is set to ON, only uplink RLC or downlink RLC can be
18) CMP_RAB_5_CFG_ROHC_SWITCH: When the switch is set to ON, the service with RAB ID 5 can be configured with the
23) CMP_HSUPA_MACD_FLOW_MUL_SWITCH: When the switch is set to ON, MAC-d flow can be multiplexed without any r
24) CMP_SMLC_RSLT_MODE_TYPE_SWITCH: If the Client Type of a positioning request is Value Added Service or Lawful
Service mapping strategy switch group.

1) MAP_HSUPA_TTI_2MS_SWITCH: When the switch is on, 2 ms TTI is supported for HSUPA.
2) MAP_INTER_RAT_PS_IN_CHANLE_LIMIT_SWITCH: When the switch is on, the PS services are transmitted on the DCH
3) MAP_PS_BE_ON_E_FACH_SWITCH: When the switch is on, the PS BE services can be transmitted on the E-FACH(E-FA
4) MAP_PS_STREAM_ON_E_FACH_SWITCH: When the switch is on, the PS streaming services can be transmitted on the E
5) MAP_PS_STREAM_ON_HSDPA_SWITCH: When the switch is on, a PS streaming service is mapped on the HS-DSCH if t
6) MAP_PS_STREAM_ON_HSUPA_SWITCH: When the switch is on, a PS streaming service is mapped on the E-DCH if the
7) MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH: When the switch is on, the signaling is transmitted at a rate of 6.8
8) MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH: When this switch is turned on, the SRB of a CS RRC connection ca
earlier than Release 6,?the RRC connection setup cause of CS services?is Originating Conversational Call or Terminating Co
a CS service.
PS rate negotiation switch group.
1) PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH: When the switch is on, access at a rate of 0 kbit/s or on the FACH is de
2) PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH: When the switch is on, the initial rate of the service should be dynamically
3) PS_BE_IU_QOS_NEG_SWITCH: When the switch is on, the Iu QoS Negotiation function is applied to the PS BE service if
4) PS_RAB_DOWNSIZING_SWITCH: When the switch is on and the RAB downsizing license is activated, the initial speed is
5) PS_STREAM_IU_QOS_NEG_SWITCH: When the switch is on, the Iu QoS Negotiation function is applied to the PS STREA
6) PS_BE_STRICT_IU_QOS_NEG_SWITCH: When the switch is on, the strict Iu QoS Negotiation function is applied to the P
the switch is not on, the loose Iu QoS Negotiation function is applied to the PS BE service,RNC select Iu max bit rate based on
different cell.The switch is valid when PS_BE_IU_QOS_NEG_SWITCH is set to ON.
Direct retry switch group.

1) DR_RRC_DRD_SWITCH(DRD switch for RRC connection): When the switch is on, DRD and redirection is performed for R
2) DR_RAB_SING_DRD_SWITCH(DRD switch for single RAB): When the switch is on, DRD is performed for single service if
3) DR_RAB_COMB_DRD_SWITCH(DRD switch for combine RAB): When the switch is on, DRD is performed for combined se
4) DR_INTER_RAT_DRD_SWITCH(INTER-RAT DRD switch): When this switch is turned on, inter-RAT directed retry is suppo
HandOver switch group.

1) HO_ALGO_HCS_SPEED_EST_SWITCH: When the switch is on, the RNC evaluates the UE's moving speed in the HCS an
2) HO_ALGO_LDR_ALLOW_SHO_SWITCH: When the switch is on, the LDR inter-frequency handover is allowed during soft
3) HO_ALGO_MBMS_FLC_SWITCH: When the switch is on, the UE requires that the redirection strategy be used for frequen
4) HO_ALGO_OVERLAY_SWITCH: When the switch is on, the associated receiving and mobility algorithms of the overlay ne
requirements of operator and restrictions of present network, overlay network realizes operation distribution and load sharing b
5) HO_INTER_FREQ_HARD_HO_SWITCH: When the switch is on, the RNC is allowed to initiate inter-frequency measure co
6) HO_INTER_RAT_CS_OUT_SWITCH: When the switch is on, the RNC is allowed to initiate inter-frequency measure contro
7) HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH: When the switch is on, the NACC function is supported during t
switch is useless. When the NACC function is supported, the UE skips the reading procedure as the SI/PSI of the target cell is
8) HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH: When the switch is on, the PS inter-RAT handover from the 3G net
9) HO_INTER_RAT_PS_OUT_SWITCH: When the switch is on, the RNC is allowed to initiate inter-frequency measure contro
10) HO_INTER_RAT_RNC_SERVICE_HO_SWITCH: When the switch is on, the attributes of inter-RAT handover of the servic
parameters.
11) HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH: When the switch is on, the cells in the detected set from which th
12) HO_INTRA_FREQ_DETSET_RPRT_SWITCH: When the switch is on, statistics on the intra-frequency measurement repo
13) HO_INTRA_FREQ_HARD_HO_SWITCH: When the switch is on, the RNC is allowed to initiate the intra-frequency hard ha
14) HO_INTRA_FREQ_RPRT_1J_SWITCH: When the switch is on, the event 1J is included in the delivery of intra-frequency
15) HO_INTRA_FREQ_SOFT_HO_SWITCH: When the switch is on, the cells on the RNC can active the soft handover. When
16) HO_MC_MEAS_BEYOND_UE_CAP_SWITCH: When the switch is on, the neighboring cell whose frequency band is beyo
17) HO_MC_NCELL_COMBINE_SWITCH: When the switch is on, the neighboring cell combined algorithm is used during the
18) HO_MC_SIGNAL_IUR_INTRA_SWITCH: When the switch is on, intra-frequency handover is allowed over the Iur interface
19) HO_MC_SIGNAL_SWITCH: When the switch is on, quality measurement on the active set is delivered after signaling setu
20) HO_MC_SNA_RESTRICTION_SWITCH: When the switch is on, the RNC controls the UEs in the connected state based o
21) HO_LTE_PS_OUT_SWITCH:This bit field is added under "Handover Algorithm Switch". HO_LTE_PS_OUT_SWITCH is th
When this bit field is selected, this switch is set to ON. In this case, the RNC is allowed to send an LTE MEASUREMENT CON
CONTROL message to the UE or to initiate an inter-RAT PS handover from UMTS to LTE.
22) HO_LTE_SERVICE_PS_OUT_SWITCH :This bit field is added under "Handover Algorithm Switch". HO_LTE_SERVICE_P
When this bit field is selected, this switch is set to ON. In this case, the RNC is allowed to send an LTE MEASUREMENT CON
send an LTE MEASUREMENT CONTROL message to the UE based on service or to initiate an inter-RAT PS service-based h
23) This bit is a Single Radio Voice Call Continuity (SRVCC) switch for the VoIP service that is handed over to GERAN. SRVC
The meaning of the bit is as follows:
When it is set to "ON", it indicates that the VoIP service can be handed over to GERAN through SRVCC procedure.
When it is set to "OFF", it indicates that the VoIP service cannot be handed over to GERAN through SRVCC procedure.
SRNSR algorithm switch group.
1) SRNSR_DSCR_IUR_RESRCE_SWITCH: When the switch is on, relocation for transmission optimization over the Iur interf
congested link. Based on PsBeProcType of "ADD UNRNC", the RNC decides whether to initiate relocation or DSCR. When th
2) SRNSR_DSCR_LOC_SEPRAT_SWITCH: When the switch is on, the RNC initiates static relocation or DSCR if the optimal
or DSCR.
3) SRNSR_DSCR_PROPG_DELAY_SWITCH: When the switch is on, the RNC initiates static relocation or DSCR if the delay
RNC decides whether to initiate relocation or DSCR.
4) SRNSR_DSCR_SEPRAT_DUR_SWITCH: When the switch is on, the RNC initiates static relocation or DSCR if the duration
CMCF algorithm switch group.

1) CMCF_DL_HLS_SWITCH: When the switch is on, the compressed mode supports DL higher-layer scheduling.
2) CMCF_UL_HLS_SWITCH: When the switch is on, the compressed mode supports UL higher-layer scheduling.
3) CMCF_UL_PRECFG_TOLERANCE_SWITCH: When the switch is on, the compressed mode of the UE in the compressed
4) CMCF_WITHOUT_UE_CAP_REPORT_SWITCH: When the RNC starts inter-frequency or inter-RAT measurement, the RN
complete message. When the switch is on and no such information has been reported, the RNC starts the compressed mode
CORRM algorithm reserved switch 0. The switch is reserved for further change request use.
1) RESERVED_SWITCH_0_BIT2: When the switch is set to ON, only uplink RLC or downlink RLC can be re-established durin
2) RESERVED_SWITCH_0_BIT3: When the switch is set to ON, signaling radio bearers (SRBs) cannot be changed from DCH
3) RESERVED_SWITCH_0_BIT4: When the switch is turned on, the RNC does not consider whether the cell is congested du
4) RESERVED_SWITCH_0_BIT5: When the switch is set to ON, the RNC establishes the BE service of a UE on R99 channel
establishment.
5) RESERVED_SWITCH_0_BIT6: When the switch is set to ON, the directed retry algorithm based on downlink load balance
6) RESERVED_SWITCH_0_BIT7: When the switch is set to ON, BE services that are already established on E-DCHs can be
7) RESERVED_SWITCH_0_BIT8: When the switch is turned on, D2F state transition is allowed regardless of whether the CC
trigger D2F state transition.
8) RESERVED_SWITCH_0_BIT9: When the switch is set to ON, the uplink 0 kbit/s transport format of subflow A of an AMR s
9) RESERVED_SWITCH_0_BIT10: When the switch is turned on, multiple cross-Iur radio links (RLs) belonging to the same D
10) RESERVED_SWITCH_0_BIT11: When the switch is turned on, the PS service must be carried by DCHs in the uplink if bo
1) RESERVED_SWITCH_1_BIT1: When the switch is set to ON, the RNC instructs the cells involved in the active set to repor
information by using an intra-frequency measurement control message. This avoids the transmission of too large measuremen
2) RESERVED_SWITCH_1_BIT2: When the switch is set to ON, the intra-frequency ReadSFNInd of a cell in system informati
CORRM algorithm reserved U32 para 0. The para of 32 bits is reserved for further change request use.
E2DRachRprtEcN0Thd(Ec/N0 Threshold for E-DCH-to-DCH Channel Switch):Ec/No decision threshold for BE service DCH es
carried on the DCH rather than the E-DCH.
ReservedU8Para0(Event 6A Relative Threshold for DCH-to-E-DCH Channel Switch):Event 6A relative threshold for triggering
for uplink, the UE reports an event 6A.
ReservedU8Para1(Event 6B Relative Threshold for DCH-to-E-DCH Channel Switch):Event 6B relative threshold for triggering
for uplink, the UE reports an event 6B.
Compatibility switch 2
1) CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH: When the switch is set to ON, the Iu user plane (UP) version is not decrea
2) CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH: When the switch is set to ON, RTT dedicated measurement adopts
dedicated measurement adopting the extended cell mode.
3) CMP_IUR_CMCF_SWITCH: When the switch is set to ON, compressed mode is started by using a RADIO LINK RECONFI
4) CMP_STTD_RL_ADD_SWITCH: When the switch is set to ON, the transmit diversity mode information element is always c
is used to solve the problem that transmit diversity parameters are incorrectly configured for softer handovers because the RA
5) CMP_STTD_ASU_SWITCH: When a UE is soft-handed over from a cell enabled with transmit diversity to a cell disabled wi
does not resend an active set update message after an active set update failure.
6) CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH: When the switch is set to OFF, a penalty is imposed on a failed directed
7) CMP_WBAMR_SUBFLOW_SWITCH: When the switch is set to ON, the number of WB AMR service substreams is configu
with the Change Request (CR) specified in the related protocol, that is, three substreams need to be established for a WB AM
8) CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH: The switch is used to solve the problem that different vendors' RN
switch is set to OFF, the RNC interprets the cell capability bitmap in the sequence specified by the related protocol.
9) CMP_MOCN_PLMN_SEL_SWITCH: When the switch is turned on, the RNC preferentially uses the common operator’s PLM
conditions is not met, the RNC preferentially uses the PLMN of the UE’s homing operator. When the switch is turned off, the R
10) CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH: When the switch is set to ON, the RNC sets the "Support for lo
is set to OFF, the RNC sets the "Support for lossless SRNS relocation or for lossless DL RLC PDU size change" IE transmitte
11) CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH: When the switch is set to ON, the RNC sets the uplink mode of an
Whether the performance enhancement function is enabled:

1) PERFENH_AMR_SPEC_BR_SWITCH: When the switch is set to ON, the procedure specific to AMR service establishment
2) PERFENH_AMR_TMPLT_SWITCH: When the switch is set to ON, the AMR template takes effect.
3) PERFENH_SRB_TMPLT_SWITCH: When the switch is set to ON, the SRB template takes effect.
4) PERFENH_OLPC_TMPLT_SWITCH: When the switch is set to ON, the OLPC template takes effect.
5) PERFENH_AMR_SP_TMPLT_SWITCH: When the switch is set to ON, the AMR parameter template takes effect.
6) PERFENH_INTRAFREQ_MC_TMPLT_SWITCH: When the switch is set to ON, the intra-frequency measurement control te
7) PERFENH_INTERRAT_PENALTY_50_SWITCH: After a UE fails to be handed over to a 2G cell during an inter-RAT hando
8) PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH: When the switch is set to ON, the uplink SRBs of HSUPA 10 ms non-co
services can be carried on HSUPA channels when the original parameter Type of Channel Preferably Carrying Signaling RB is
9) PERFENH_HSUPA_TTI2_ENHANCE_SWITCH: When the switch is set to ON, the single-user peak-rate improvement algo
10)PERFENH_UU_P2D_CUC_OPT_SWITCH: When this switch is turned on,the P2D cell update confirm message simplificat
11)PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH:This check box controls whether the RNC considers the converged SI
If the check box is not selected, the RNC sends the initial SIRTarget value used after radio link reconfiguration to the NodeB.
If the check box is selected, the RNC selects a more appropriate value from the initial SIRTarget value used after radio link rec
Setting of this check box takes effect only when the PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH check box is selected.
12)PERFENH_RRC_REDIR_PROTECT_SWITCH: When the switch is set to ON, The mechanism to avoid endless back-and-
Threshold for the amount of the traffic handled by the CPUS. When the amount of traffic is above this threshold, traffic handled
Uniquely identifying a FACH bearing the common transport channel in a cell
The switch of control plane flow control.
The control rate, when congestion level from others to low.
The control rate of RRC, when the congestion level from high to high.
The control rate of RRC, when the congestion level from overload to overload.
The control rate of RRC, when the congestion level rises.
The control rate of RRC, when the congestion level descends.
Forwarding threshold of control plane load sharing. When the CPU usage is between the sharing threshold and overload thres
The sharing offset should be added to the target subrack or subsystem. This parameter is used for preferable selection of the
Maximum numbers of incoming calls in one second when the load exceeds the forwarding threshold. When the CPU usage is
subsystem.
Numbers of incoming calls to be shared when the load exceeds the forwarding threshold. When the CPU usage is between th
SharingOutCAPSMidLoad in this version supports configuration synchronization and delivery, but the RNC does not use this p
Maximum numbers of incoming calls in one second when the load is lower than the forwarding threshold. When the CPU usag
SPU subsystem.
Uniquely identifying a classified zone. The value of Classified Zone ID is denoted by decimal numerals.
For a BE service that has a low maximum rate, the DCCC algorithm is not obviously effective yet it increases algorithm proces
For a BE service that has a low maximum rate, the DCCC algorithm is not obviously effective yet it increases algorithm proces
When the BE service rate decreases to the DCCC threshold rate, the UE, however, cannot perform state transition to FACH s
performed. The timer parameters and traffic volume measurement parameters for the function of low activity rate adjustment a
Strategy for adjustment of the rate of the PS BE service when the UE is in the CELL_DCH state. RATE_UP_AND_DOWN_ON
the threshold for DCCC before state transition to CELL_FACH. That means UE can transit to CELL_FACH state at any rate.
Strategy of the UE for rate adjustment over the EDCH. RATE_UP_AND_DOWN_ON_EDCH indicates that the rate over the E
DCCC before state transition to CELL_FACH. That means UE can transit to CELL_FACH state at any rate over the EDCH.
The relative power margin of single BE traffic, used to calculate the triggering threshold of event F, can avoid the fluctuation of
The relative power margin of combined traffics, used to calculate the triggering threshold of event F, can avoid the fluctuation o
This parameter determines whether the UL rate is raised to the maximum rate in one step or two steps for BE service set up o
This parameter determines whether the UL rate is lowered to the minimum rate in one step or two steps for BE service set up
This parameter determines whether the uplink intermediate rate uses automatic or manual mode when using 3-step adjustmen
Threshold of the UL intermediate rate when the 3-step mode is used for UL rate adjustment and the manual mode is used for
This parameter determines whether the DL rate is raised to the maximum rate in one step or two steps for BE service set up o
This parameter determines whether the DL rate is lowered to the minimum rate in one step or two steps for BE service set up
This parameter determines whether automatic or manual mode is used for 3-step adjustment of the DL intermediate rate.
Threshold of the DL intermediate rate when the 3-step mode is used for DL rate adjustment and the manual mode is used for
This parameter specifies the threshold of allowed times of rate increase consecutive failure within a certain monitoring period.
Length of the period within which the times of consecutive failure to increase the rate of a BE service is monitored. Increase of
DCCC Rate Up Fail Penalty Timer expires.
Length of the penalty period within which the rate of a BE service cannot be increased even if the 4A measurement report is re
Maximum UL rate when coverage of the entire cell is ensured under certain load. For a BE service that has a low maximum ra
Maximum DL rate during network planning when coverage of the entire cell is ensured. When the DL TCP is limited, the curren
processing. Thus, the DCCC algorithm is applied to BE services whose maximum DL rate is greater than the threshold.
This parameter specifies the period of DCH throughput ratio measurement.Macd performs statistic of traffic volume on DCH an
Threshold for rate decrease of HSUPA BE service soft handover. If the current rate is beyond the threshold, the rate over the
Throughput event 4B threshold for BE service E-DCH-to-DCH channel switch in the uplink based on coverage
Index of an IMSI number segment

The parameter specify whether to use the IMSI number segment configuration mode or the IMSI filter character configuration m
single digit or several digits in IMSI numbers are definite.
The paremeter specify start value of an IMSI number segment.
The paremeter specify the end value of an IMSI number segment.
The paremeter specify the filter character of an IMSI number segment.
The paremeter specify the Fixed value in an IMSI number segment. When the parameter IMSI Number Segment Configuration
The parameter specify the priority of a terminal type. This parameter is only used to identify terminals. The parameter Hierarch
The parameter specify UE support capability of a cell. Value 0 indicates that the cell does not admit UEs. A larger value of this
The parameter specify Data card support capability of a cell. Value 0 indicates that the cell does not admit data cards. A larger
Reserved Parameter
This parameter specifies whether the distance based RRC redirection algorithm is valid. The algorithm is valid only when the t
Redirection algorithm works only when the propagation delay between UE and NodeB is larger then this threshold. For details
When the UL load state or DL load state of the serving cell is LDR(basic congestion) or OLC(overload congestion), a UE may
redirection is not performed if the load state on the serving cell is LDR or OLC.
When the load of the serving cell is within the normal range, a UE may be redirected to another cell according to the distance
cell is within the normal range.
Delay for the initial macro diversity combination. After changing to the macro diversity state from the non-macro diversity state
combination after the delay when the first uplink data packet is received. For the CS service, changing the value of this param
Protection delay for the Iub FP to wait for the synchronization response frame of transport channels. This protection delay plus
regards that the transport channel synchronization fails or retransmits the downlink synchronization frame.
Protection delay for the Iub FP to wait for the node synchronization response frame. This protection delay plus the delay over
synchronization fails or retransmits the downlink node synchronization frame.
Protection delay for the Iur FP to wait for the synchronization response frame of transport channels. This protection delay plus
that the transport channel synchronization fails or retransmits the downlink synchronization frame.
Protection delay for the Iur FP to wait for the node synchronization response frame. This protection delay plus the delay over t
synchronization fails or retransmits the downlink node synchronization frame.
Time adjustment switch of the Iu interface. If this switch is turned on, the CN adjusts the time of sending data on the Iu interfac
Threshold for determining congestion of the E-DCH on the Iub interface based on the frame loss ratio. If the frame loss ratio e
Switch of checking the E-DCH congestion on the Iub interface. If this switch is turned on, the E-DCH congestion check functio
Whether the cyclic redundancy check (CRC) function is enabled.
When the switch is on, the congestion detection and control for DL R99 service is supported.
Threshold for determining congestion of a single service based on the packet loss ratio. One of the conditions for the congesti
Note: If the packet loss ratio is greater than the value of "PacketLossRatioThld" and the number of lost packets is greater than
Threshold for determining congestion of a single service based on the number of lost packets. One of the conditions for the co
Note: If the packet loss ratio is greater than the value of "PacketLossRatioThld" and the number of lost packets is greater than
Whether the function of controlling the congestion of the HSUPA service on the Iur interface is enabled.
Delay for determining congestion in the uplink transport layer. If the delay is greater than this parameter value, you can regard
Threshold for determining congestion in the uplink transport layer based on the packet loss ratio. One of the conditions for the
"TnlPacketLossRatioThld" and the number of lost packets is greater than the value of "TnlPacketLossNumThld", you can rega
Threshold for determining congestion in the uplink transport layer based on the number of lost packets. One of the conditions
value of "TnlPacketLossRatioThld" and the number of lost packets is greater than the value of "TnlPacketLossNumThld", you
Threshold 2 for determining congestion in the uplink transport layer based on the number of lost packets. If the number of lost
TCP Accelerator function switch.
1) TPE_DOWNLINK_SWITCH: When the switch is on, the Downlink TCP Accelerator function is supported.
2) TPE_UPLINK_SWITCH: When the switch is on, the Uplink TCP Accelerator function is supported.
Adjustment period of the weight of the service priority indication (SPI).

Specifies the coefficient for adjusting service priority weight in the matching record.(Adjusted SPI Weight = min (Initial SPI weig
Note: Parameter "ServicePriAdjCoef" will be replaced with "ServPriAdjCoefHigh", "ServPriAdjCoefMiddle", and "ServPriAdjCoe
Specifies the factor for adjusting the performance percent of two SPI weight adjust strategy.
Maximum time coefficient for delivering the adjustment factor of SPI weight. If the time is greater than the result of 10 multiplie
R99 congestion control switch. If this switch is turned on, the R99 congestion control function is supported.
HSUPA congestion control switch. If this switch is turned on, the HSUPA congestion control function is supported.
This parameter specifies whether to enable the counters contained in the measurement units QoS and SPI.
This parameter specifies the anti-DDoS flow control threshold for the LBO function. In the LBO function, the system allows onl
this case, the system calculates the number of TCP SYN packets received in a second. If the number exceeds the value of the
This parameter specifies the anti-spoofing threshold for the LBO function. In the LBO function, the system considers the uplink
spoofing IP packets received from a UE exceeds the value of this parameter, the system releases the RRC connection of the U
This parameter specifies the scheduling priority weight that corresponds to high-priority services.
This parameter specifies the scheduling priority weight that corresponds to middle-priority services.
This parameter specifies the scheduling priority weight that corresponds to low-priority services.
This parameter specifies the length of RAB PDP Alive Detect Timer in offload status.
This parameter specifies the length of RAB Keep Alive Timer in offload status.
Threshold for reporting FACH congestion.
Threshold for recovering FACH congestion.
Threshold for clearing FACH congestion.
Switch specifying whether the ACK message is constructed automatically in TCP mode. When the switch is turned on, the AC
DRD rollback switch. When the switch is turned on, the DRD rollback function is supported.
Switch of measuring the time taken by the RNC to send the HSDPA data.
When the switch is turned on, the RNC checks whether HSDPA data exists in the buffer within the data scheduling period afte
When the switch is turned off, the RNC checks whether HSDPA data exists in the buffer within the data scheduling period befo
Paging preemption switch. When the switch is turned on, the paging preemption function is supported.
Switch of silence detection and tracing. When the switch is turned on, the function of silence detection and tracing is supported
AMR noise change switch. When the switch is turned on, the AMR noise change function is supported.
TPE multi-threading switch. When the switch is turned on, the TPE multi-threading function is supported.
This parameter specifies the threshold for triggering inter-subrack load balancing for smart services. The inter-subrack load ba
Reserved Switch 1.
Reserved Switch 2.

Maximum number of inter-RAT RAB directed retries. It decides the size of the candidate set for inter-RAT DRD. The value 0 in
Whether the service steering DRD algorithm is applied. Cell-level service steering DRD switch, if configured, needs to be enab
Whether the load balancing DRD algorithm is applied to DCH services.
- ON: The load balancing DRD algorithm will be applied.(If cell-level DRD parameters are configured, the status of cell level lo
Whether the load balancing DRD algorithm is applied to HSDPA services.
- ON: The load balancing DRD algorithm will be applied.(If cell-level DRD parameters are configured, the status of cell level loa
Whether load balancing DRD is based on power or on user number.
- Power: Power(Downlink none-HSDPA power is used for DCH services, and downlink HSDPA guarantee power is used for H
- UserNumber: User number(Downlink R99 equivalent user number is used for DCH services, and downlink HSDPA user num
RRC redirection switch used in the case of admission failure. It is valid only when the "DR_RRC_DRD_SWITCH" parameter is
- OFF indicates that the RRC redirection is not allowed.
- Allowed_To_Inter_RAT indicates that both RRC redirection to inter-frequency cells and redirection to inter-RAT cells are allow
Threshold of remnant load offset between the current cell and the target cell when load balancing DRD is applied to DCH user
be satisfied, that is, total power remnant difference between the current cell and target cell must be less than "Load Balance D
Threshold of remnant load offset between the current cell and the target cell when load balancing DRD is applied to HSDPA u
also be satisfied, that is, total power remnant difference between the current cell and target cell must be less than "Load Balan
Downlink load threshold to trigger load balancing DRD for DCH services. The load balancing DRD will be triggered only when
Downlink load threshold to trigger load balancing DRD for HSDPA services. The load balancing DRD will probably be triggered
Threshold of the total downlink remnant power difference between the current cell and the target cell when load balancing DRD
cell. The other condition is that remnant load offset reaches the threshold defined by the parameter of "Load Balance DRD Off
Whether to apply the code balancing DRD algorithm. The "DR_RAB_SING_DRD_SWITCH" parameter in "SET UCORRMALG
Threshold of code occupancy offset between the current cell and the target cell when code balancing DRD is applied. Only wh
One of the triggering conditions of code balancing DRD. The other condition is the code occupancy threshold. Code balancing
One of the triggering conditions of code balancing DRD. The other condition is the minimum spreading factor. Code balancing
BAND4
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
This parameter specifies whether to enable the uplink load balance for DC-HSDPA traffic. The uplink load balance is performe
If the difference of the remaining number of equivalent users in the uplink between the target cell and the serving cell is greate
This parameter specifies the threshold of triggering the uplink load balance for DC-HSDPA traffic. If the remaining number of e
Controls the validity of the measurement-based DRD algorithm. Assume that the DRD algorithm is enabled. If the switch is on
switch is off, the RNC implements the DRD algorithm based on blind handovers. Note: When the measurement-based DRD al
DRD is performed only for the periodic retry flow.
The parameter specify whether to enable the terminal type hierarchy algorithm.
Whether to enable DRD for technological satisfaction of non-MIMO legacyH in STTD mode.
Whether to enable DRD for technological satisfaction of non-MIMO legacyH in primary and secondary CPICH mode.
Filtering coefficient in CQI measurement.
The duration that the CQI keeps higher than Ea threshold or lower than Eb threshold for reporting event Ea or Eb. This param
Unit for the CQI reporting period after event E is reported. The unit can be 10 ms or minutes.
CQI is reported periodically after event Ea is reported. This parameter specifies the reporting period. For example, if this param
CQI is reported periodically after event Ea is reported. This parameter specifies the reporting period.
The duration that the CQI keeps higher than Fa threshold or lower than Fb threshold for reporting event Fa or Fb. This parame
Unit for the CQI reporting period after event F is reported. The unit can be 10 ms or minutes.
CQI is reported periodically after event Fa is reported. This parameter specifies the reporting period. For example, if this param
CQI is reported periodically after event Fa is reported. This parameter specifies the reporting period.
Whether to enable the automatically triggered DSAC algorithm.
Whether to impose the access restriction on the CS domain.
Whether to impose the access restriction on the PS domain.
Specifies the number of access classes that are restricted at a time according to the flexible polling restriction mode.
Specifies the restricted access class according to the flexible polling restriction mode.
Specifies the interval between consecutive pollings imposed on the PS domain and CS domain in different cells according to t
Specifies the interval delay between consecutive pollings according to the flexible polling restriction mode.
Inter-frequency handover protection duration in the case of non-urgent spectrum withdrawal. After the RNC receives a comma
Inter-RAT handover protection duration in the case of non-urgent spectrum withdrawal. After the RNC receives a command of
a result, urgent spectrum withdrawal is frequently triggered by GSM. Setting this parameter to too small a value causes UEs u
Period of periodical handovers performed when a non-urgent spectrum withdrawal needs to be performed.
Number of UEs to be handed over in each handover period when a non-urgent spectrum withdrawal needs to be performed.
Duration used to protect blind inter-frequency handovers that are performed when a spectrum needs to be withdrawn urgently
Traffic class whose DTX_DRX parameters are to be set
E-DCH TTI type
Whether the parameters related to the DTX are valid. Value OFF indicates that the parameters related to the DTX are invalid a
Number of consecutive EDCH TTIs carrying no data, which triggers the interval at which two consecutive patterns are transmit
Number of preamble timeslots sent before data is transmitted on the DPCCH when patterns with the size of "DtxCycle2" are tr
Period during which no data is transmitted on the E-DCH. For details, see 3GPP TS 25.321.
Number of subframes transmitted when the priority of reporting CQI is higher than the priority of transmitting patterns on the U
Number of consecutive subframes that can be transmitted on the UL DPCCH during one "DtxCycle1". For details, see 3GPP T
Number of consecutive subframes that can be transmitted on the UL DPCCH during one "DtxCycle2". For details, see 3GPP T
Whether the parameters related to the DRX are valid. The parameters related to the DRX are optional and they can be set onl
DRX are valid.
Size of patterns (that is, the number of subframes) that can be received on the HS-SCCH. For details, see 3GPP TS 25.214.
Number of consecutive subframes that the UE needs to monitor on each HS-SCCH of the HS-SCCH set immediately after the
Number of subframes that the UE needs to monitor on the E-AGCH of the serving radio link and on the E-RGCH of each radio
Whether the UE monitors the transmission on the E-AGCH in the serving EDCH cell and the transmission on each E-RGCH in
25.214.
CQI feedback cycle in DTX-DRX mode. Currently, the value of this parameter can be set to only D2. For details, see 3GPP TS
Size of patterns, that is, the number of subframes that can be transmitted on the UL DPCCH. For details, see 3GPP TS 25.214
Size of patterns, that is, the number of subframes that can be transmitted on the UL DPCCH. For details, see 3GPP TS 25.214
DTX cycle at the MAC layer when the MAC layer supports UL E-DCH deactivation. For details, see 3GPP TS 25.321.
This parameter specifies the RLC priority of the traffic mapping the DSCP value 0.
his parameter specifies the RLC priority of the traffic mapping the DSCP value 21.
his parameter specifies the RLC priority of the traffic mapping the DSCP value 22.
HSUPA traffic uplink rate adjustment set. It contains rates for rate adjustment for uplink channel of HSUPA traffic and is used i
When this parameter is on, the packet missing ratio for voice service needs to be considered during dynamic TTI adjustment.
This parameter is used only for the TTI dynamic adjustment algorithm (2ms to 10 ms) for differentiation-based BE services. W
only for copper users.
Event A triggering threshold in the packet missing ratio measurement for AMR services.
Threshold for triggering event 6A1 for AMR services. Event 6A1 is reported through a measurement report, and is triggered wh
= Maximum uplink transmit power - Value of this parameter.
Threshold for triggering event 6B1 for AMR services. Event 6B1 is reported through a measurement report, and is triggered wh
Event A triggering threshold in the packet missing ratio measurement for WB-AMR services.
Threshold for triggering event 6A1 for WB-AMR services. Event 6A1 is reported through a measurement report, and is triggere
6A1 = Maximum uplink transmit power - Value of this parameter.
Threshold for triggering event 6B1 for WB-AMR services. Event 6B1 is reported through a measurement report, and is triggere
6B1 = Maximum uplink transmit power - Value of this parameter.
Event A triggering threshold in the packet missing ratio measurement for VoIP services.
Threshold for triggering event 6A1 for VoIP services. Event 6A1 is reported through a measurement report, and is triggered wh
Threshold for triggering event 6B1 for VoIP services. Event 6B1 is reported through a measurement report, and is triggered wh
Threshold for triggering event 6A1 for BE services. Event 6A1 is reported through a measurement report, and is triggered whe
Maximum uplink transmit power - Value of this parameter.
Threshold for triggering event 6B1 for BE services. Event 6B1 is reported through a measurement report, and is triggered whe
Threshold for triggering event 6A2 for BE services. Event 6A2 is reported through a measurement report, and is triggered whe
Threshold for triggering event 6B2 for BE services. Event 6B2 is reported through a measurement report, and is triggered whe
Lower rate threshold for TTI from 2ms to 10ms can be calculated by multiplying this parameter by "Rate threshold of BE on 2m
Upper rate threshold for RTWP/Coverage-based TTI from 2ms to 10ms can be calculated by multiplying this parameter by "Ra
Upper rate threshold for CE-based TTI from 2ms to 10ms can be calculated by multiplying this parameter by "Rate threshold o
Rate threshold for TTI from 10ms to 2ms can be calculated by multiplying this parameter by "Rate threshold of BE on 2ms TTI
Resource type that triggers TTI adjustment based on user fairness and differentiated services.
Correspondence between Access Classes (ACs) 0-9 and an ASC. For details, see 3GPP TS 25.331.
Start index of available signatures for an Access Service Class (ASC) in the enhanced RACH (ERACH) function. For details, s
End index of available signatures for an ASC in the enhanced RACH (ERACH) function. For details, see 3GPP TS 25.331.
Identifying available subchannels for an ASC in the ERACH function. The subchannel number is a four-bit string. When a UE d
"AND" operation together with the bit string (12) identifying the available subchannel assigned to the PRACH, and a 12-bit dat
Transmission Timing" is set to 0. Then, the bit string is put into an "AND" operation together with the bit string (12) identifying t
25.331.
Used for calculating dynamic persistence values corresponding to ASCs 2 to 7. This parameter is intended only for ASCs 2 to
Transmission Time Interval (TTI) for the common E-DCH. For details, see 3GPP TS 25.331.
Available preamble signatures for ERACH UEs. An ERACH UE is considered to be applying for the E-DCH only when the UE
Available Subchannels for UEs that attempt to access a network using the ERACH function. For details, see 3GPP TS 25.331
Used for calculating the transmit power for the first access preamble during random access in the following formula: Preamble
indicates the downlink transmit power for the primary CPICH. CPICH_RSCP indicates the Received Signal Code Power (RSC
Maximum number of preambles in one preamble ramping cycle. For details, see 3GPP TS 25.331.
Power ramp step from power for transmitting the previous preamble. Power is ramped up when a UE retransmits a preamble a
Maximum number of preamble cycles during random access. For details, see 3GPP TS 25.331.
Upper bound for random back-off. This parameter specifies the longest period of time after which a UE can reinitiate a random
Lower bound for random back-off. This parameter specifies the shortest period of time after which a UE can reinitiate a random
Number of common E-DCH resources that need to be configured in a cell
Maximum bit rate that can be provided by each ERACH E-DCH resource
Guaranteed bit rate that can be provided by each ERACH E-DCH resource
Maximum Transmission Block (TB) size for ERACH UEs at the edge of a cell that supports E-DCH transmission.
Unique ID of a GSM cell
A name identifying a GSM cell uniquely.
The Index of neighboring BSC that the GSM cell belongs to.
Inquiring load of GSM cell when the switch is on.

The code of the country to which the BSC belongs.
The code of the mobile communication network to which the BSC belongs.
Indicating a Cn Operator Group.
Location Area Code (LAC) of the GSM cell.

Note: H'0000 and H'FFFE are reserved values.
This parameter identifies whether to configure RAC. If the RNC supports the PS domain, this parameter must be set to REQU
This parameter defines a routing area within a location area for the PLMN of GSM-MAP type. Routing Area Code (RAC) is def
Identifying a GSM cell.
Uniquely identifying the different network in the neighboring area.
Uniquely identifying a neighboring base station with the same carrier.

Identifying BCCH frequency number of the inter-RAT cell.
BCCH: Broadcast Control Channel
GSM1900
Frequency number: (511-811)
GSM1800
GSM900
Frequency number: (0-125) or (954-1024)
GSM850
GSM450
GSM480
When the inter-RAT cell frequency number is within the range 512-810, the parameter indicates whether this frequency numbe
Identifying the type of the inter-RAT cell NO_CAPABILITY indicates that the capacity of the GSM cell remains unknown. It is n
This parameter indicates whether HCS is used.
This parameter indicates the HCS priority level The smaller the coverage of the cell is, the higher the priority level of the cell sh
Quality threshold for HCS reselection.
Indicating the network control mode.
Identifying whether the inter-RAT cell supports RIM. (RIM is used to obtain the SI/PSI information of the inter-RAT cell.) For th
Identifying whether the inter-RAT cell supports PS HO. TRUE indicates that the inter-RAT cell is able to perform the handover
It is set according to the topographic feature.

This parameter is used for the inter-RAT handover decision in combination with the neighboring cell oriented CIO. The larger t
The larger the value of the parameter is, the easier it is to be handed over to the GSM network. The smaller the value of the pa
Identifying a Neighboring RNC.
Uniquely identifying a neighboring RNC cell.

Specifies the host type of a cell. This parameter specifies the host type of a cell in the case that the RNC node redundancy fea
parameter is set to"DOUBLE_HOST_OUT_POOL", the cell is controlled by two RNCs not including SRNC. When the primary
This parameter specifies the index of the operator group that serves the cell.
Primary downlink scrambling code.
This parameter specifies the selected frequency bands during cell setup.
This parameter indicates whether to configure the UL frequency of the cell.
TRUE indicates that the UL frequency need be reconfigured.
FALSE indicates that the UL frequency need not be reconfigured. It is configured automatically based on the relationship betw
NULL indicates that the UL frequency remains unchanged.
Band9: UL frequency = DL frequency - 475
Depending on the value of [BandId], as shown below:

Band1
Common frequencies [9612-9888]
Special frequencies none
Band2
Special frequencies {12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287}
Band3
Band4
Special frequencies {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
Band5
Special frequencies {782, 787, 807, 812, 837, 862}
Band6
Special frequencies {812, 837}
Band7
Special frequencies {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
Band8
Band9
BandIndNotUsed [0-16383]
This parameter indicates the DL frequency of a cell.
Depending on the value of [BandId], as shown below:
Band1
Band2
Special frequencies {412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687}
Band3
Band4
Special frequencies {1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087}
Band5
Special frequencies {1007, 1012, 1032, 1037, 1062, 1087}
Band6
Special frequencies {1037, 1062}
Band7
Special frequencies {2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912}
Band8
Band9
BandIndNotUsed [0-16383]
Identifying a Slave RNC.
Slave cell identity.
This parameter indicates whether transmission diversity configuration of the cell's downlink common physical channels is activ
This parameter identifies a location area code.
This parameter identifies whether to configure RAC. If the RNC supports the PS domain, this parameter must be set to REQU
This parameter indicates the routing area code.

This parameter indicates whether to configure the minimum quality level. When it is set to FALSE, the UE adopts the correspo
command.
This parameter defines the CPICH Ec/No access threshold of the cell. The UE can camp on the cell only when the measured
For FDD cells, the cell selection criterion S in the 25.304 protocol is defined as follows:
Srxlev>0 AND Squal>0
Where:
- Squal = Qqualmeas - Qqualmin
- Srxlev = Qrxlevmeas - Qrxlevmin - Pcompensation
- Qqualmeas is the measured cell quality value, namely CPICH Ec/No.
- Qrxlevmeas is the measured cell RX level value, namely CPICH RSCP.
- Qrxlevmin is the minimum required quality level in the cell.
- Pcompensation = max(UE_TXPWR_MAX_RACH-P_MAX, 0)
- UE_TXPWR_MAX_RACH is the maximum TX power level a UE may use when accessing the cell on RACH, namely MaxAllo
- P_MAX is the maximum RF output power of the UE.
The larger the value of the parameter is, the more difficult it is for the UE to camp on the cell. The smaller the value of the para
When this parameter is not set to any value, the UE adopts the corresponding value of the current serving cell, added through
This parameter indicates whether to configure the minimum RX level. When it is set to FALSE, the UE adopts the correspondi
This parameter defines the CPICH RSCP access threshold of the cell.This parameter is the minimum required RX level that co
The settings of "Qrxlevmin" and "Qqualmin" should be considered along with each other.
The larger the value of the parameter is, the more difficult it is for the UE to camp on the cell. The smaller the value of the para
When this parameter is not set to any value, the UE adopts the corresponding value of the current serving cell, added through
This parameter indicates whether the actual value of Qrxlevmin should be added with the value of DeltaQrxlevmin or not. If Qr
The actual minimum required RX level = the minimum required RX level ([Qrxlevmin]) + the extended minimum required RX le
This parameter indicates whether to configure the maximum TX power.
This parameter specifies the maximum allowed uplink TX power of a UE in the cell. When this parameter is not set to any valu
This parameter indicates whether HCS is used.
This parameter indicates the HCS priority level The smaller the coverage of the cell is, the higher the priority level of the cell sh
Quality threshold for HCS reselection.
This parameter indicates whether to support the mode change of downlink power control (DPC).
This parameter indicates whether STTD TX diversity is supported.
This parameter indicates whether the closed loop TX diversity mode 1 supported.
The parameter takes for adjusting the phase and amplitude of the DL dedicated channel upon reception of response from the
Specifies the TX diversity mode on DPCH for the non-MIMO users and non-DC-HSDPA users.
Specifies the TX diversity mode on F-DPCH for the non-MIMO users and non-DC-HSDPA users.
Specifies the TX diversity on DPCH mode for the MIMO users.

Specifies the TX diversity mode on F-DPCH for the MIMO users.
Specifies the TX diversity mode for the DC-HSDPA users.
According to the protocol 3GPP TS 25.211, the DC-HSDPA feature can use STTD TX diversity mode only. For details, see 3G
1)DELAY_ACTIVATION_SUPPORT (delay activation support indicator):when the indicator is TRUE, it means that the cell sup
2)HSDSCH_SUPPORT(HSDSCH support indicator):when the indicator is TRUE, it means that the cell support HSDSCH and
3)FDPCH_SUPPORT(F-DPCH support indicator):when the indicator is TRUE, it means that the cell support F-DPCH and ena
4)EDCH_SUPPORT(E-DCH support indicator):when the indicator is TRUE, it means that the cell support E-DCH and enable u
5)EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTI support indicator):when the indicator is TRUE, it means that the cell support E
6)EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max SF support 2SF2+2SF4 indicator):when the indicator is TRUE, it means
7)EDCH_2SF2_SUPPORT(E-DCH max SF support 2SF indicator):when the indicator is TRUE, it means that the cell has E-DC
8)EDCH_2SF4_SUPPORT(E-DCH max SF support 2SF4 indicator):when the indicator is TRUE, it means that the cell has E-D
9)EDCH_SF4_SUPPORT(E-DCH max SF support SF4 indicator):when the indicator is TRUE, it means that the cell has E-DC
10)EDCH_SF8_SUPPORT(E-DCH max SF support SF8 indicator):when the indicator is TRUE, it means that the cell has E-DC
11)EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH support HARQ IR Combining indicator):when the indicator is TRUE, it mea
12)EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support HARQ CHASE Combining indicator): when the indicator is T
13) CPC_DTX_DRX_SUPPORT (CPC DTX-DRX support indicator): when the indicator is TRUE, it indicates that the cell supp
14) CPC_HS_SCCH_LESS_OPER_SUPPORT (CPC HS-SCCH less operation support indicator): when the indicator is TRUE
15) HSPAPLUS_MIMO_SUPPORT (MIMO support indicator): when the indicator is TRUE, it indicates that the cell supports M
16) FLEX_MACD_PDU_SIZE_SUPPORT (flexible MAC-d PDU Size support indicator): when the indicator is TRUE, it indicate
17) FDPCH_SLOT_FORMAT_SUPPORT (F-DPCH slot format support indicator): when the indicator is TRUE, it indicates that
set true.
18) HSPAPLUS_DL_64QAM_SUPPORT (downlink 64QAM support indicator): when the indicator is TRUE, it indicates that the
Mobility flag of the overlay network.
This flag is valid when the OVERLAY switch is set to ON. When the flag is set to NOT_FORBIDDEN, this means that, when us
that, when using the H service, the UE cannot deliver the intra-frequency measurement and handover to the neighboring cell,
Note that the H+CS combined service is considered as the CS service.
This parameter indicates whether the cell of the neighboring RNC supports the HARQ Preamble capability. Mode1 means the
The CIO value specified in this parameter cooperates with the neighboring cell oriented CIO. For details about the meaning of
E_FACH support indicator. When the indicator is TRUE, it indicates that the cell supports E_FACH.
Access point (AP) cell indicator. When the indicator is "TRUE", it indicates that the cell is an AP cell. AP is a device for access
Indicates whether the videophone (VP) service is limited in a cell. When the indicator is "TRUE", it indicates that the VP servic
Uniquely identifying a common physical channel in a cell

Uniquely identifying a FACH in a cell. Configured according to the product specifications.
The rate matching factor of a transport channel.For detailed information of this parameter, refer to 3GPP TS 25.212.
A positive value relative to Time of arrival window endpoint (ToAWE). It indicates the startpoint of the arrival time window for a
A positive value relative to Latest Time of Arrival (LToA). It indicates the endpoint of the arrival time window for a downlink dat
The offset between the FACH transmit power and P-CPICH transmit power in a cell.
Maximum common channel priority supported by FACH
Minimum common channel priority supported by FACH.
Indicating whether the FACH bears signalling
The coding type of a transport channel. For detailed information of this parameter, refer to 3GPP TS 25.212.
The coding rate of a transport channel. For detailed information of this parameter, refer to 3GPP TS 25.212.
This parameter specifies the traffic class. According to the QoS requirements of services, there are four traffic classes: conver
User priority that is defined according to the Allocation/Retention Priority (ARP) from the RAB assignment. The user classes in
This parameter specifies the maximum available bandwidth for each traffic class in the CELL_FACH stat with the downlink HS
E_FACH to CELL_DCH will be triggered. This parameter needs to be set according to the traffic class.
This parameter defines the RLC size corresponding to each transport format. For a common channel, the "RLC Size" reflects t
This parameter defines the number of the transport formats corresponding to the RLC size in the TF set. For detailed informat
This parameter defines the number of the transport blocks corresponding to the TF 1 of the RLC size in the TF set. The param
This parameter defines the number of the transport blocks corresponding to the TF 2 of the RLC size in the TF set. For detaile
This parameter defines the number of the transport blocks corresponding to the TF 3 of the RLC size in the TF set. For detaile

Offset between TPC command power in F-DPCH channel and reference F-DPCH TX power (represented by the Initial DL Tra
This parameter specifies the maximum reference power for the F-DPCH, relative to the assigned P-CPICH power. For details
This parameter specifies the minimum reference power for the F-DPCH. This parameter indicates the minimum value of refere
Constant that is used by the RNC to calculate the DPCCH_Power_Offset which is further used by the UE to calculate the UL D
The formulas are as follows:
DPCCH_Power_Offset = Primary CPICH DL TX power + UL interference + Default Constant Value
Here, DPCCH_Power_Offset is the DPCCH initial transmit (TX) power offset, Primary CPICH DL TX power is the downlink TX
DPCCH_Initial_Power = DPCCH_Power_offset - CPICH_RSCP

Here, CPICH_RSCP is the received signal code power of the P-CPICH measured by the UE.
A small value of DPCCH_Power_Offset might lead to uplink synchronization failure at cell edges during link setup, thus affecti
This parameter specifies how the UE interprets the received Transmit Power Control (TPC) commands, that is, selecting a UL
transmit power once every timeslot. When the parameter is set to ALGORITHM2, the UE adjusts the uplink transmit power on
Step of the closed-loop power control performed on UL DPCH. For details, see 3GPP TS 25.214.
Step of the closed-loop power control performed on DL DPCH in Frequency Division Duplex (FDD) mode. For details, see 3GP
DL power control mode.
- SINGLE_TPC, a fast power control mode, indicates that a unique TPC command is sent in each timeslot on the DPCCH.
- TPC_TRIPLET_IN_SOFT, a slow power control mode, indicates that the same TPC command is sent over three timeslots. I
- TPC_AUTO_ADJUST, an automatic adjustment mode, indicates that the value of DPC_MODE can be modified by sending
For details, see 3GPP TS 25.214.
This parameter specifies whether the DL code-resource-saving mode is applicable to narrowband AMR services, ON specifies
rate of single AMR service is lower than or equal to 7.95 kbit/s, while SF128 is used if the code-resource-saving mode is not a
This parameter specifies the puncturing limit used in the spreading factor calculation algorithm for DL DPCH in code-resource-
UTRAN-specific Discontinuous Reception (DRX) cycle length coefficient. In connected mode, the UE uses the shorter one bet
case, the UE needs to monitor only one paging indication in one paging occasion during each DRX cycle.
A value too small causes the UE to check the paging channel frequently, thus having great power consumption. A value too la
UL initial access rate of PS background or interactive service. When DCCC function is enabled, the uplink initial access rate w
through negotiation when congestion occurs. A smaller value indicates that BE services is easier to be accessed. It is not reco
DL initial access rate of PS background or interactive service. When DCCC function is enabled, the downlink initial access rate
This parameter specifies the upper limit of uplink BE service rate in combined AMR services. Combined AMR services consist
This parameter specifies the upper limit of downlink BE service rate in combined AMR services. Combined AMR services cons
This parameter specifies the upper limit of uplink BE service rate in combined non-AMR services. Combined AMR services co
This parameter specifies the upper limit of downlink BE service rate in combined non-AMR services. Combined AMR services
E-DCH data transfer mode of streaming services. It is valid only when streaming services are mapped onto the E-DCH.
Time interval of sending HSUPA scheduling information alone for TTI 10ms when the user has no Schedule Grant and its buff
Time interval of sending HSUPA scheduling information alone for TTI 2ms when the user has no Schedule Grant and its buffe
Time interval of sending HSUPA scheduling information for TTI 10ms when the user has Schedule Grant
Time interval of sending HSUPA scheduling information for TTI 2ms when the user has Schedule Grant
HSUPA BE traffic initial bit rate. When DCCC algorithm switch and HSUPA DCCC algorithm switch are enabled, the uplink init
DL initial access rate used when HSDPA BE services switch to the DCH.
Whether it is allowed to use the initial rate of IMS signaling set on the LMT, that is, the value of "IMS Initial Rate[kbit/s]".
- ON: If the IMS signaling is carried on the DCH, the maximum rate of IMS signaling adopts the value of "IMS Initial Rate[kbit/
- OFF: The maximum rate of IMS signaling does not adopt the value of "IMS Initial Rate[kbit/s]".
Initial access rate of IMS signaling. When the "IMS Bearer Enhancement Switch" is ON:
- If the IMS signaling is carried on the DCH in the downlink, the initial rate adopts the larger value between this parameter and
- If the IMS signaling is carried on the HSPA, the MBR adopts the larger value between this parameter and the RAB-assigned
TTI type used for VoIP services over the E-DCH
Rate threshold of 2ms TTI on the E-DCH for the PS streaming service. The 2ms TTI is used on the E-DCH when it is supporte
This parameter specifies the rate threshold of 2ms TTI on the E-DCH for HSUPA BE service. When the cell capability and UE
Threshold for determining the signal quality in a cell. If the reported Ec/No exceeds the value of this parameter, you can infer t
Time duration when the reported Ec/No is valid. The reported Ec/No is valid for the period (starting from the time when the Ec/
This parameter specifies the maximum size of PDUs transmitted at the MAC layer when the UE is in the CELL_DCH state in th
This parameter specifies the maximum RLC PDU size when the UE is in CELL_DCH state and UL Layer 2 Enhanced is enabl
This parameter specifies the minimum RLC PDU size when the UE is in CELL_DCH state and UL Layer 2 Enhanced is enable
Maximum size of PDUs transmitted at the MAC layer when the UE is in the CELL_FACH state in the L2 enhancement mode
According to the R8 protocol, MIMO and 64QAM can be used together. When the condition is not met, for example the cell do
Delay time for DTX_DRX being effective after it is enabled. For details, see 3GPP TS 25.331.
This parameter specifies which HSPA technologies can be retried by UEs. When the HSPA technologies are selected and cur
Whether the DPCCH slot format 1 or DPCCH slot format 4 is used when all the traffic and signaling are transmitted over the H
TTI type used for CS services over the uplink HSPA channel.
Relative delay for jitter correction of the CS traffic over the uplink HSPA channel. The CS data is buffered on the PDCP layer a
Relative delay for jitter correction of the CS traffic over the downlink HSPA channel. This parameter indicates the maximum CS
E-DCH data transfer mode of IMS signaling services. It is valid only when IMS signaling services are mapped onto the E-DCH
E-DCH data transfer mode of SRBs. It is valid only when SRBs are mapped onto the E-DCH.
This switch is used to configure the priority of MIMO_64QAM or DC-HSDPA. According to different protocols, the following situ
priorities of the features. When the priority of MIMO is higher than that of DC-HSDPA, the priority of 64QAM is higher than tha
This parameter specifies the threshold for triggering the 16QAM for the HSUPA traffic. The 16QAM data transmission is perfor
Identifies the PTT traffic. The RNC identifies the PTT traffic based on the information elements (IEs) in the RAB assignment re
Vulnerability" and "Queuing Allowed" in the ARP is equal to the configured "PTTArpPriorityLevel", "PTTArpPreEmptCap", "PTT
UTRAN-specific Discontinuous Reception (DRX) cycle length coefficient for PTT User
TTI type used for the PTT services over the E-DCH
This parameter is used to specify SPI Weight when the licence for SPI Weight-based differentiated services is disabled.
Maximum size of PDUs transmitted at the MAC layer when the UE is in the CELL_PCH state in the L2 enhancement mode
ImprovementMaximum MAC-d PDU size when both ERACH and UL Layer 2 Improvement are activated.
ImprovementMinimum MAC-d PDU size when both ERACH and UL Layer 2 Improvement are activated.
E-DCH data transfer mode of PTT services. It is valid only when PTT services are mapped onto the E-DCH.
Downlink transmit power threshold of a DC-HSDPA secondary cell. When DC-HSDPA and MIMO Selection Switch is turned o
equal to "SecCellHUserNumThd". Otherwise, DC-HSDPA is enabled.
Threshold of the number of HSDPA users in a DC-HSDPA secondary cell. When DC-HSDPA and MIMO Selection Switch is tu
than or equal to "SecCellTcpThd". Otherwise, DC-HSDPA is enabled.
Channel type of CS voice services. DCH indicates that both uplink and downlink are preferably carried on DCH. HSPA indicate
be carried on HS-DSCH.
Type of channel that preferably carries VoIP services.
- DCH: Both uplink and downlink are preferably carried on the DCH.
- HSDPA: Uplink is preferably carried on the DCH, and downlink is preferably carried on the HS-DSCH.
- HSPA: Uplink is preferably carried on the E-DCH, and downlink is preferably carried on the HS-DSCH.
This parameter specifies the channel type of PTT services.
- DCH: Both uplink and downlink are preferably carried on DCH.
- HSDPA: Uplink is preferably carried on DCH, and downlink is preferably carried on HS-DSCH.
- HSPA: Uplink is preferably carried on E-DCH, and downlink is preferably carried on HS-DSCH.
Channel type of IMS signaling.
- DCH: Both uplink and downlink are preferably carried on the DCH.
- HSDPA: Uplink is preferably carried on the DCH, and downlink is preferably carried on the HS-DSCH.
- HSPA: Uplink is preferably carried on the E-DCH, and downlink is preferably carried on the HS-DSCH.
Type of channel that preferably carries the signaling RB.
- DCH: Both uplink and downlink are preferably carried on DCH.
- HSDPA: Uplink is preferably carried on DCH, and downlink is preferably carried on HS-DSCH.
- HSUPA: Uplink is preferably carried on E-DCH, and downlink is preferably carried on DCH.
- HSPA: Uplink is preferably carried on E-DCH, and downlink is preferably carried on HS-DSCH.
Whether the configured type of channel that preferably carries the signaling RB is effective in the case of RRC connection esta
Rate threshold for the decision to set up a PS domain background/interactive service on the DCH in the uplink. Only when the
specifications, only the background/interactive services whose rate is lower than 16 kbit/s can be carried on the CCH. Therefo
Rate threshold for the decision to set up a PS domain background/interactive service on the DCH in the downlink. Only when t
the specifications, only the background/interactive services whose rate is lower than 16 kbit/s can be carried on the CCH. The
Rate threshold for decision to use HS-DSCH to carry DL PS streaming services. When the maximum DL service rate is higher
Rate threshold for decision to use HS-DSCH to carry DL PS background/interactive services. When the maximum DL service
Rate threshold for decision to use E-DCH to carry PS streaming services. When the maximum UL rate is higher than or equal
This parameter specifies the rate threshold for decision to use E-DCH to carry UL PS domain background/interactive services.
Ethernet port
Whether Gi interface shares Ethernet port with IuPS interface
VLANID of the Gi interface
Maximum time interval between sending of path detection message at the local end and reception of a response message from
Maximum number of times the path detection message is retransmitted when no response to the path detection message is re
Echo detection switch. When the switch is turned, the Echo detection function is supported.
Iu-PS self-healing switch. When the switch is turned on, the Iu-PS self-healing function is supported.
Iu-PS check switch. When the switch is turned on, the Iu-pS check function is supported.
Time window for estimating whether the UE is in high-mobility state.

The start point of the estimation is the moment of the last reporting of event 1D, and the backdated time length is determined b
Threshold for determining whether the UE is in high-mobility state.

After the UE reports event 1D, the UE is considered in high-mobility state if the number of changes of the best cell during "TFa
Period for determine whether the UE is in low-mobility state.
The RNC periodically determines whether the UE is in low-mobility state. The smaller the value is, the more frequently the stat
Time window for deciding whether the UE is in low-mobility state.

Every time the slow speed period timer expires, the RNC estimates whether the UE is in low-mobility state. This parameter spe
Threshold for determining whether the UE is in low-mobility state.

After the UE reports event 1D, the UE is considered in low-mobility state if the number of changes of the best cell is smaller th
Time window for determining whether ping-pong handover occurs in the best cell during the UE speed estimation.
In the speed estimation algorithm, an algorithm is adopted to avoid inaccurate estimation caused by frequent handovers of be
The given time length is set by this parameter. If this parameter is set too great, the RNC may mistakenly determine that ping-
There are two combination methods for uplink combination of soft handover: one is maximum ratio combination at the NodeB
the NodeB decides whether to implement maximum ratio combination according to its own physical conditions; when MUST is
Consider the working status (test/normal operation) and the propagation environment when deciding whether to implement so
HSPA serving cell change is usually triggered by event 1D. To avoid frequent serving cell change which may affect the system
serving cell change shall be performed until the timer expires. However, this timer shall not restrict HSPA serving cell change t
This parameter specifies the event 2D/2F measurement threshold of which measurement type (inter-frequency or inter-RAT m
When COEXIST_MEAS_THD_CHOICE_INTERFREQ is selected, event 2D/2F measurement thresholds oriented towards inte
When COEXIST_MEAS_THD_CHOICE_INTERRAT is selected, event 2D/2F measurement thresholds oriented towards inter-
The factors such as the event 2D/2F measurement thresholds for inter-frequency measurement and inter-RAT measurement,
inter-frequency measurement, and inter-frequency neighboring cells are preferred when inter-RAT and inter-frequency neighb
This parameter determines the maximum number of links in the EDCH active set. When the RNC acts as the SRNC, the numb
transferred over multiple EDCH links in macro diversity, thus affecting the system performance. If this parameter value is too s
After the coverage based handover succeeds, to avoid the handover of the UE to another frequency due to the following facto
measurement caused by the previous factors before the timeout of the timer. The larger this parameter, the better effect the an
CQI power offset from the UL DPCCH when the UE is in the single-RLS state. When the value is set too low, CQI resolution o
CQI power offset from the UL DPCCH when the UE is in the multi-RLS state. When the value is set too low, CQI resolution of
Number of CQI retransmissions when the UE is in the single-RLS state. Assume that the CQI repetition factor is N. The receiv
Number of CQI retransmissions when the UE is in the multi-RLS state. Assume that the CQI repetition factor is N. The receive
Duration of a CQI feedback cycle when the UE is in the single-RLS state. In each CQI feedback cycle, the UE retransmits CQI
Duration of a CQI feedback cycle when the UE is in the multi-RLS state. In each CQI feedback cycle, the UE retransmits CQI
Period of sending the channel quality indication (CQI) feedback of conversational services.
Period of sending the channel quality indication (CQI) feedback of non-conversational services in MIMO mode without DC-HA
Period of sending the channel quality indication (CQI) feedback of non-conversational services in MIMO+DC-HSDPA mode, e
Traffic class whose HS-SCCH Less Operation parameters are to be set
Whether the MAC-ehs entity is applied. Mac-ehs is enhanced Mac-hs and is used for DL L2 enhancement function. If the DL L
Whether the configured HS-SCCH Less Operation parameters adopt the octet-aligned or bit-aligned mode. Octet-aligned mod
Number of Mac-hs transport blocks that can be used in HS-SCCH Less Operation mode
Index of the Mac-hs transport block size that can be used in HS-SCCH Less Operation mode. For details about the mapping b
Whether the Mac-hs transport block transmitted in HS-SCCH Less Operation mode supports the second HS-PDSCH code. Fo
T300 is started when UE sends the RRC CONNECTION REQUEST message. It is stopped when UE receives the RRC CONN
Maximum number of retransmissions of the RRC CONNECTION REQUEST message.
T312 is started when UE starts to establish a DCH, and stopped when UE detects consecutive N312 "in sync" indications from
Maximum number of successive "in sync" indications received from L1.
Sum of the maximum transmit power of all DL channels in a cell. For detailed information of this parameter, refer to 3GPP TS
Maximum transmit power on a FACH that carries an MCCH for IMB services. The MCCH for IMB services is carried on a FAC
ID of a cluster. A cluster is a cell group, in which all the cells operate in Multimedia Broadcast Multicast Service (MBMS) over a
Number of a frequency used in a cell. The range of downlink UTRA Absolute Radio Frequency Channel Numbers (UARFCNs)
Band a:
UARFCN range of common frequencies: 9512 to 9588, 10062 to 10113
UARFCN range of special frequencies: none
Band b:
UARFCN range of common frequencies: 9262 to 9538, 9662 to 9938
Band c:
UARFCN range of common frequencies: 9562 to 9638
Band d:
UARFCN range of common frequencies: 12862 to 13088
UARFCN range of special frequencies: 2112, 2137, 2162, 2187, 2212, 2237, 2262, 2287, 2312, and 2337
Band indicator not used: 0 to 16383
Note: Different frequency bands correspond to different UARFCN ranges.
For details about this parameter, see 3GPP TS 25.102.
Difference between the System Frame Number (SFN) and NodeB Frame Number (BFN) of the NodeB which the cell belongs
Sequence Number of a DL primary scrambling code in a cell. For detailed information of this parameter, refer to 3GPP TS 25.2
Whether a cluster is reserved for operators. If a cluster is reserved for operators, UEs allocated access class 11 or 15 in the lo
Whether a cluster is reserved for extension. If a cluster is not reserved for operators but for extension, UEs regard the cell as b
Duration after which a UE can measure a cluster when the cluster is reserved for operators or for extension. For details about
Data rate of an IMB service.
Maximum transmit power on a FACH.
Power offset of SCCPCH Frame Type 2 in 16QAM modulation. For details about this parameter, see 3GPP TS 25.433.
ID of a neighboring cluster.
ID of a common physical channel in a cell.

Number of Integrated Mobile Broadcast (IMB) services carried on one transport channel.
Index of an operator.
ID of an IMB service.
Number of a subframe carried on Secondary Common Control Physical Channel Frame Type 2 (SCCPCH FT2). For details ab
Number of the first channelization code allocated to SCCPCH FT2. For details about this parameter, see 3GPP TS 25.433.
Number of the last channelization code allocated to SCCPCH FT2. For details about this parameter, see 3GPP TS 25.433.
Modulation scheme used over SCCPCH FT2. For details about this parameter, see 3GPP TS 25.433.
Timeslot format over a physical channel. For details about this parameter, see 3GPP TS 25.221.
Whether Integrated Mobile Broadcast (IMB) is supported. If this parameter is set to ON, IMB is enabled.
The function of the TAC.If Fast_Dormancy is selected, the TAC specifies the UEs that are enabled with the Fast Dormancy fea
Type Allocation Code (TAC) is part of the International Mobile Station Equipment Identity (IMEI), it is used to identify the type o
Description UE type.
The switch of Fast Dormancy function for one type UE.
1) FD_P2D_SWITCH (TAC-Level P2D Control Switch)

When the switch is turned on, state transition from CELL_PCH/URA_PCH to CELL_DCH of a UE is triggered if the following c
1. The TAC of the UE is the same as that configured on the RNC.
2. The UE is in the CELL_PCH or URA_PCH state, and the RNC receives a CELL UPDATE message containing a cause valu
When the switch is turned off, state transition from CELL_PCH/URA_PCH to CELL_DCH is not triggered by the CELL UPDAT
In this case, however, the state transition can be triggered by other factors in the system. For example, if the UE is in the CELL
2) FD_TAC_FORCE_D2F_SWITCH (TAC-based D2F Switch for UEs Supporting Fast Dormancy)
When the switch is turned on, state transition from CELL_DCH to CELL_FACH is forcibly performed on the UE with the corres
When the switch is turned off, CELL_DCH to CELL_PCH/URA_PCH state transition is forcibly performed on the UE with the c
Minimum of IMSI route parameter in Intra Domain NAS Node Selector(IDNNS).
Maximum of IMSI route parameter in Intra Domain NAS Node Selector(IDNNS).

The minimum of one IMSI range.
The maximum of one IMSI range.
Indicating whether the SNAC need be configured.
TRUE: The SNAC need be configured.
FALSE: The SNAC need not be configured. UE can access any cell of the PLMN.
Sharing Network Area Code.
The code of the country to which the RNC belongs.
The code of the mobile communication network to which the RNC belongs.
Cell-oriented inter-frequency measurement report mode
There are two inter-frequency handover report modes in the RNC, namely, event-triggered report and periodical report. The re
Event-triggered report mode
In this mode, event 2B is used to decide whether to trigger inter-frequency handover. This prevents the ping-pong handover (T
trigger threshold"). Event 2B cannot change from event-triggered mode to periodical mode. When event-triggered measureme
load are saved. Comparing the signal quality between intra-frequency and inter-frequency handovers, the ping-pong effect in h
each time when the best cell is updated, the inter-frequency measurement parameters should be updated accordingly.
Periodical report mode
In this mode, event 2D/2F is used to start and stop the compressed mode, and to periodically report the inter-frequency cell m
timer expires, the inter-frequency handover is started after the timer expires.
If the handover fails, the handover decision is performed, according to the periodical inter-frequency measurement report.
The advantage of the periodical measurement report mode is that it can repeatedly perform direct retry on the same cell when
handover decision is performed in the RNC. The disadvantage of the periodical measurement report mode is that it requires la
As for the impact on network performance,the two measurement report modes have both advantages and disadvantages. Cur

Hysteresis for triggering event 2B.
Hysteresis for triggering event 2D.

frequency handover.
Hysteresis for triggering event 2F.

frequency handover.
triggered in time.
If this parameter is set to a greater value, the higher quality of the active set is obtained. If this parameter is set to 0, the gener
TS 25.331. This parameter is used for event-triggered reporting of inter-frequency handovers for events 2D, 2F, 2B and 2C, bu
Interval time between the detection of event 2B and sending of measurement report. This parameter correlates with slow fadin
interval can effectively reduce the average number of handovers and the number of incorrect handovers, preventing unnecess
rate is less sensitive to this interval. Therefore, for the cell with most of the fast-moving UEs, this parameter can be set to a sm
Interval time between detection of event 2D and sending of the measurement report. This parameter correlates with slow fadin
Interval time between detection of event 2F and sending of the measurement report.This parameter correlates with slow fading
Ec/No threshold of triggering the inter-frequency measurement for CS services.

Ec/No threshold of stopping the inter-frequency measurement for CS services.

Ec/No threshold of triggering the inter-frequency measurement for PS non-HSPA services.

When Ec/No is used as the measurement quantity for PS non-HSPA services, the UE reports event 2D when the measured E
Ec/No threshold of triggering the inter-frequency measurement for HSPA services.

Ec/No threshold of stopping the inter-frequency measurement for PS non-HSPA services.
When Ec/No is used as the measurement quantity for PS non-HSPA services, the UE reports event 2F when the measured Ec
Ec/No threshold of stopping the inter-frequency measurement for HSPA services.

RSCP threshold of triggering the inter-frequency measurement for CS services.

RSCP threshold of stopping the inter-frequency measurement for CS services.

RSCP threshold of triggering the inter-frequency measurement for PS non-HSPA services.

RSCP threshold of triggering the inter-frequency measurement for HSPA services.

RSCP threshold of stopping the inter-frequency measurement for PS non-HSPA services.
When RSCP is used as the measurement quantity for PS non-HSPA services, the UE reports event 2F when the measured R
RSCP threshold of stopping the inter-frequency measurement for HSPA services.

Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for CS
target frequency is higher than this threshold. If the inter-frequency reporting mode is set to "PERIODIC_TRIGGER", this para
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for no
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of Ec/No for HS
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for CS
the quality of the target frequency is higher than this threshold. If the inter-frequency reporting mode is set to "PERIODIC_TRI
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for no
Threshold of the target frequency for triggering inter-frequency measurement based on measurement quantity of RSCP for HS
than the start threshold for event 2D or equal to the threshold of event 2F.
for triggering event 2B can be met only when the quality of the uesd frequency is smaller than this threshold. In addition, even
for triggering event 2B can be met only when the quality of the used frequency is smaller than this threshold. In addition, even
Sets the interval between the failure in the inter-frequency handover triggered by the event 2B and the inter-frequency handov
Maximum number of inter-frequency handover re-attempts after event 2B is reported when the measurement control message
If this parameter is set to a greater value, the number of inter-frequency handover re-attempts increases and the possibility of
measurement control message to allow the UE to be handed over to other cells of this frequency.
If the measurement control is released, the inter-frequency handover re-attempt is stopped.
Maximum delay before triggering the inter-frequency coverage handover.
If the inter-frequency coverage handover priority of the cell reporting the MR is equal to the highest priority of the target cell de
the measurement control list, the inter-freq coverage handover delay timer is enabled.
When the timer expires, the inter-freq handover is triggered.
Threshold of signal quality of the target frequency for triggering inter-frequency measurement.
This parameter is used to set measurement control on the event 2C.
The event 2C is triggered when the signal quality of the target frequency is above this threshold.

If the inter-frequency handover for event 2C fails, the RNC reties the inter-frequency handover. This parameter specifies the in
to the target cell whose load is reduced. The RNC load, however, increases.
Maximum number of handover attempts for event 2C.
This parameter specifies the maximum number of handover re-attempts for event 2C when the measurement control message
the number of re-attempts reaches the preset value, the RNC does not attempt to perform the handover. Alternatively, when th
ID of an RNC
Unique ID of a cell
Unique RNC ID of a neighboring cell
Unique ID of a neighboring cell
Neighboring cell oriented CIO.

This parameter specifies the neighboring cell oriented Cell Individual Offset (CIO). The sum of the value of this parameter, the
used for moving the border of a cell. In the case of an event-based intra-frequency measurement or inter-RAT measurement, t
parameter when evaluating an inter-frequency measurement event.
In the case of a periodical inter-frequency measurement or inter-RAT measurement, the RNC determines whether to initiate a
Cell offset used for CPICH RSCP measurement value in cell selection or reselection when the UE is in idle mode.
Offset of neighboring cell CPICH measurement value. This parameter is used for RSCP measurement. The offset is subtracte
(RNP) based on the actual network. If this parameter is set to a greater value, the probability for cell reselection reduces.
Note that in FDD mode, this parameter is valid only when SIB11 Indicator is set as TRUE.
Cell offset used for CPICH Ec/No measurement value in cell selection or reselection when the UE is in idle mode.
Offset of neighboring cell CPICH measurement value. This parameter is used for Ec/No measurement. The offset is subtracte
(RNP) based on the actual network.
Cell offset used for CPICH RSCP measurement value in cell selection or reselection when the UE is in connected mode. Durin
"Conn" for connected mode. ConnQoffset1sn and ConnQoffset2sn are valid only when "SIB12Ind" is set to "TRUE", indicating
cell reselection. In handover algorithms, this parameter is used for moving the border of a cell. This parameter can be configur
Cell offset used for CPICH Ec/No measurement value in cell selection or reselection when the UE is in connected mode. Durin
cell reselection.In handover algorithms, this parameter is used for moving the border of a cell. This parameter can be configure

Cell offset used for CPICH Ec/No measurement value in HCS cell selection.
If this parameter is set to a greater value, the probability for cell reselection reduces. If this parameter is set to a smaller value,
Priority for neighboring cell supporting coverage-based inter-frequency handover.

The value "0" indicates that the coverage-based inter-freqency handover is not supported. The value "1" indicates that the cell
as the measurement object and the target cell for the handover increases. For example, the cell with priority 1 has more chanc
Whether to perform blind handover.

The value FALSE indicates that the cell is not considered as a candidate cell for blind handover. Therefore, blind over to this c
Quality condition for triggering the blind handover.

If this parameter is not set to -115, a conditional blind handover can be triggered in an inter-frequency neighboring cell with the

The priority that corresponds to the neighboring cell is valid only when the parameter is set to TRUE. The neighboring cell with
DRD Ec/No threshold for determining whether to perform the blind handover. If the measured Ec/No of the current cell is great
Whether the cell supports the measure-based directed retry (MBDR) algorithm.
The value TRUE indicates that the cell supports the MBDR algorithm, and the value FALSE indicates that the cell does not su
Priority of a MBDR cell.

This parameter is valid only when the "MBDRFlag" parameter is set to TRUE. It indicates the tiptop priority when the value is s
when there are many of cells meet the quality condition. Attention, when there does not have cell meet the quality condition ba
Specify the flags of the cells that the DRD measurement or LDR measurement is performed.
The value "TRUE" indicates that the cell can be considered as the measurement object in the DRD measurement algorithm or
Indicates whether the signal quality in neighboring cells is guaranteed. If the parameters Qqualmin and Qrxlevmin for the neigh
Cell reselection is performed only when the signal quality in the expected neighboring cell is above Qqualmin and Qrxlevmin.
Minimum CPICH Ec/No for the neighboring cell on cell reselection. The neighboring cell can be involved in cell sorting for rese
Qqualmin from SIB3. For details, see the 3GPP TS 25.331. According to the 3GPP TS 25.304, S criterion for cell reselection is
Here,
Squal = Qqualmeas - Qqualmin
Srxlev = Qrxlevmeas - Qrxlevmin - Pcompensation
"Qqualmeas" refers to the measured CPICH Ec/No.
"Qrxlevmeas" refers to the CPICH RSCP.
"Qrxlevmin" refers to the minimum CPICH receive power in the current cell.
Pcompensation = max(UE_TXPWR_MAX_RACH - P_MAX, 0)
"UE_TXPWR_MAX_RACH", also named as "MaxAllowedULTxPower", refers to the maximum uplink transmit power when the
"P_MAX" refers to the maximum RF output power of the UE.
Minimum CPICH RSCP for the neighboring cell on cell reselection. The neighboring cell can be involved in cell sorting for rese
Qrxlevmin from SIB3. For details, see the 3GPP TS 25.331. Qrxlevmin should be set to a proper value, to match Qqualmin.
Inter-RAT measurement reporting mode.

Event-triggered reporting
To avoid the ping-pong effect before and after the inter-RAT handover, use event 3A (quality of the currently used frequency is
the BSIC of the GSM cell whose event 3A needs to be triggered must be decoded correctly by the UE. The reporting mode of
The advantage of event-triggered reporting is that the signaling transmission and processing load are saved. Comparing the s
cannot be changed to periodical reporting. For the cell-oriented algorithm parameters, each time when the best cell is updated
Periodical reporting
If the handover fails, the handover re-attempt is made again according to the periodical inter-RAT measurement report.
The advantage of periodical reporting is that it can be used for repeated handover re-attempts on the same cell when the hand
needs not to inform the UEs of the parameter change through signaling messages after the handovers. The drawback of perio
The two reporting modes have both advantage and drawback. Currently, the traditional periodical reporting mode is preferred.
L3 filtering coefficient for event 2D or event 2F measurement

increases.
Measurement quantity used in coverage-based inter-RAT measurement in event 3A-triggered reporting mode.
When CPICH_Ec/No is selected, it indicates that the Ec/No measurement quantity is used for event 3A measurement. The ph
When CPICH_RSCP is selected, it indicates that the RSCP measurement quantity is used for event 3A measurement. The ph
When AUTO is selected, it indicates that the Ec/No measurement quantity is used for event 3A measurement if the RNC recei
increases.
This parameter is used for event 3A evaluation. For detailed information of this parameter, refer to 3GPP TS 25.133.
To set this parameter, see the method for setting the intra-frequency handover weighting factor "Weight".

Hysteresis for event 2D.
This parameter is used to avoid the ping-pong reporting of event 2D (the estimated quality of the currently used frequency is b
triggered in time. If this parameter is set to a smaller value, ping-pong reporting of event 2D is likely to occur.
Hysteresis for event 2F.

The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the probability of ping-po
The inter-RAT measurement hysteresis in periodical reporting mode is used to prevent the ping-pong reporting of event 2D (th
compressed mode and event 2F is used to disable the compressed mode. "Hystfor2D" can be increased slightly based on the
active set updates.
Hysteresis for event 3A.
The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the ability of resisting sig
another RAT where the UE needs to be handed over to must be of good quality. Therefore, the criteria for triggering the inter-R
Hysteresis for inter-RAT periodical reporting.

This parameter is used to avoid incorrect decisions caused by unexpected jitters of signals during inter-RAT handover decision
If this parameter is set to a greater value, the ability of resisting signal fluctuation improves and the number of ping-pong hand
of good quality. Therefore, the criteria for triggering the inter-RAT handover decision is hard to be fulfilled, and the call drop rat
Interval time between detection of event 2D and sending of the measurement report.
Interval time between detection of event 2F and sending of the measurement report.
Interval time between detection of event 3A and sending of the measurement report.

Threshold of triggering inter-RAT measurement for CS services when measurement quantity is Ec/No.
speeds. The emulation result shows that the call drop rate remains low for the UEs moving at a speed of 120 km/h when this p
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is Ec/No.
When Ec/No is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2D when the mea
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is Ec/No.
When Ec/No is used as the measurement quantity for PS domain HSPA services, the UE reports event 2F when the measure
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is Ec/No.
Threshold of triggering inter-RAT measurement for CS services when measurement quantity is RSCP.
Threshold of stopping inter-RAT measurement for CS services when measurement quantity is RSCP.
Threshold of triggering inter-RAT measurement for PS domain non-HSPA services when the measurement quantity is RSCP.
When RSCP is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2D when the mea
Threshold of triggering inter-RAT measurement for HSPA services when measurement quantity is RSCP.
Threshold of stopping inter-RAT measurement for PS domain non-HSPA services when the measurement quantity is RSCP.
When RSCP is used as the measurement quantity for PS domain non-HSPA services, the UE reports event 2F when the mea
Threshold of stopping inter-RAT measurement for HSPA services when measurement quantity is RSCP.
For CS services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is used to set the cri
decision.
Here,
Quality requirement for the cell of another RAT during inter-RAT handover for PS domain non-HSPA services.
For PS domain non-HSPA services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is
than the quality of the currently used frequency. If the value of "Inter-RAT Reporting Mode" is set to "PERIODICAL_REPORTI
decision.
Here,
Quality requirement for the cell of another RAT during inter-RAT handover for HSPA services.
For PS services, if the value of "Inter-RAT Reporting Mode" is set to "EVENT_TRIGGER", this parameter is used to set the cri
decision.
Here,
Ec/No quality threshold for used frequency of CS services.

For CS services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Repor
Here,
Ec/No quality threshold for used frequency of PS domain non-HSPA services.
For PS domain non-HSPA services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value o
Here,
Ec/No quality threshold for used frequency of HSPA services.

For HSPA services, if Ec/No is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Rep
Here,
RSCP quality threshold for used frequency of CS domain services.
For CS services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Repor
Here,
RSCP quality threshold for used frequency of PS domain non-HSPA services.

For PS domain non-HSPA services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value o
Here,
RSCP quality threshold for used frequency of HSPA services.
For HSPA services, if RSCP is used as the measurement quantity for inter-RAT measurement and the value of "Inter-RAT Re
Here,

decreases.
Length of the timer to avoid ping-pong handovers between 2G and 3G networks.
3A report. The value 0 indicates that the system does not take measures to avoid ping-pong handover between 2G and 3G ne
Hysteresis to avoid ping-pong handover between 2G and 3G networks.
used for inter-RAT measurement. The value 0 indicates that the system does not take measures to avoid ping-pong handover
Interval between handover attempts for event 3A.
This parameter specifies the interval between handover attempts for event 3A. If this parameter is set to a smaller value, hand
however, cause the increase in the RNC load.
Maximum number of handover attempts after inter-RAT handover triggered by event 3A fails.
This parameter specifies the maximum number of handover re-attempts for event 3A when the measurement control is valid. I
reaching the value specified by this parameter, the RNC makes no further handover attempt to the target cell. If the compresse
attempts.
increases.

decision.
Here,
decision.
Here,
Maximum number of inter-RAT handover attempts after the non-coverage-based handover failures. For each handover attemp

decreases.
If this parameter is set to "ON", the RNC informs the GSM network of the load carried by the UMTS cell before the non-covera
strategy when the 3G-to-2G handover is required. When the UE is handed over from the UMTS network to the GSM network,
When this parameter is set to "ON", the RNC will stop the non-coverage based inter-RAT handover if the load of the GSM cell
GSM network based on the load of the GSM cell. The GSM network is required inform the UMTS network of its load informatio
cell. This parameter is invalid when the GSM network cannot provide the load information to the UMTS network.
This parameter specifies the threshold for 2G load of relocation target, in an inter-RAT handover in CS domain. When the GSM
This parameter specifies the threshold for 2G load of relocation target, in an inter-RAT handover in PS domain. When the GSM
This parameter specifies the interval between the handover re-attempts for event 3C. If this parameter is set to a smaller value
attempts, however, cause the increase in the RNC load.
Maximum number of handover re-attempts for event 3C.
This parameter specifies the maximum number of handover attempts for event 3C when the measurement control message is
After reaching the value specified by this parameter, the RNC makes no further handover attempt to the target cell. If the comp
attempts.
According to 3GPP TS 25.331, the filtered measurement value is calculated using the following formula, where k represents th
Fn = (1 - a) * Fn - 1 + a * Mn
a = (1/2)(k/2)
Here,
Fn: filtered measurement result
Fn - 1: previously filtered measurement result
Mn: latest received measurement result from physical layer
When a is set to 1, L3 filtering is not applied.
The input measurement value to L3 filter has been filtered by L1 filter, where the impact of fast fading is almost eliminated. In t
measurement value, and provide more reliable measurement result for event judgment.
Quantity of the triggered measurements for intra-frequency handovers. This parameter specifies the reference measurement q
threshold, the measurement quantity should be set based on the reality of the cell. If the cell is located in the center of the cov
factor that affects signal quality is the distance between the cell and the base station. In this case, you are advised to set this p
Maximum number of reporting event 1A after the reporting mode is changed to periodical reporting. When the number of repor
Interval at which event 1A is reported after the reporting mode is changed to periodical reporting. Generally, event 1A is report
reported for "PeriodMRReportNumfor1A" times at the interval specified by this parameter. If the mode of reporting event 1A is
Maximum number of reporting event 1C after the reporting mode is changed to periodical reporting. When the number of repo
Interval at which event 1A is reported after the reporting mode is changed to periodical reporting. Generally, event 1C is report
reported for "PeriodMRReportNumfor1C" times at the interval specified by this parameter.If the mode of reporting event 1C is
Maximum number of reporting event 1J after the reporting mode is changed to periodical reporting. When the number of repor
Interval at which event 1J is reported after the reporting mode is changed to periodical reporting. Generally, event 1J is reporte
reported for "PeriodMRReportNumfor1J" times at the interval specified by this parameter.If the mode of reporting event 1J is s
Relative threshold for event 1A decision when VP service is performed. If this parameter is set to a greater value, the probabili
pong handover.
set increases. In this case, more UEs are in soft handover status; however, more forward resources are occupied.If this param
Relative threshold for event 1A decision when non-VP service is performed in CS domain. If this parameter is set to a greater
threshold can directly affect the SHO ratio. Therefore, the threshold should be wisely chosen to achieve smooth SHOs.
The value of this parameter determines the SHO area and SHO ratio. In the CDMA system, the ratio of the UE involved in soft
is at least 2) is about 35%. you are advised to set the relative threshold to a great value (5 dB to 7 dB) during site deployment,
Relative threshold for event 1A decision when PS service is performed. If this parameter is set to a greater value, the probabili
pong handover.
Relative threshold for event 1B decision when VP service is performed. If this parameter is set to a smaller value, the probabil
pong handover.
Relative threshold for event 1B decision when non-VP service is performed in CS domain. If this parameter is set to a smaller
threshold can directly affect the SHO ratio. Therefore, the threshold should be wisely chosen to achieve smooth SHOs. The va
when the relative threshold is set to 5 dB, the ratio of the UE involved in soft handover (the number of cells in the active set is
to avoid the ping-pong handover.
Relative threshold for event 1B decision when PS service is performed. If this parameter is set to a smaller value, the probabil
pong handover.
Ec/No absolute threshold for event 1F in the SHO algorithm. This parameter must be set to the value that guarantees the qual
RSCP absolute threshold for event 1F in the SHO algorithm. This parameter must be set to the value that guarantees the qua
This parameter specifies the hysteretic value for event 1A. The value of this parameter is associated with the slow fading. If th
parameter, see 3GPP TS 25.331. Event 1A, as a key event, refers to the event triggered when a cell is added to the active set
the ratio of soft handovers (SHOs) may be affected. In addition, filter coefficient and interval time must be considered in setting
This parameter specifies the hysteretic value for event 1B. The value of this parameter is associated with the slow fading, and
parameter.
This parameter specifies the hysteretic value for event 1C. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1D. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1F. The value of this parameter is associated with the slow fading, and
this parameter.
This parameter specifies the hysteretic value for event 1J. The value of this parameter is associated with the slow fading, and
parameter.
Used for calculating the relative threshold of the soft handover based on the measurement report of each cell in the active set.
parameter is set to 0, the general quality of the active set is the quality of the best cell. In this case, the relative threshold of so
when maximum ratio combining is performed in the downlink of all cells in the active set.
This parameter specifies the interval time between detection of event 1A and sending of the measurement report. The value o
Setting an appropriate triggering delay effectively reduces the average number of handovers and the number of wrong handov
This parameter specifies the interval time between detection of event 1B and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1C and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1D and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1F and sending of the measurement report. The value o
This parameter specifies the interval time between detection of event 1J and sending of the measurement report. The value of
Maximum evaluation period of SHO failure. When the rate reduction evaluation is performed on a cell that fails to join the activ
a greater value, the probability for the target cell to join the active set becomes high; however, since the RNC can handle only
Maximum number of SHO failures. This parameter specifies the maximum number of event reporting from the cell that fails to
value, the probability for rate reduction of active set becomes high; In this case, the cell that fails to be added to the active set
reduction evaluation period, and the reporting intervals of event 1A and 1C. Otherwise, the reports cannot reach the required n
Relative threshold for immediate rate reduction after soft handover failure. The rate reduction of the active set and SHO retry p
Here,
Mnew: the CPICH Ec/No measurement value of the failed cell1
CPICH Ec/No measurement value in the latest measurement report of the best cell identified by the RNC according to 1D
RelThdForDwnGrd: the relative threshold for direct rate reduction. It can be configured on the OMU server.
Note: If this parameter is set to smaller value, the probability of triggering SHO rate reduction becomes low; however, the intra
reduction becomes high, and the signal quality is guaranteed; however, frequent triggering of SHO rate reduction may affect th
Length of penalty timer for SHO failure after rate reduction in the active set. When the rate reduction in the active set is perform
set is prohibited, but rate reduction is not prohibited. Such penalty strategy is applied in the following scenario: If a cell, for som
the active set. If the cell fails to be added to the active set, the rate in the active set may increase during the evaluation proces
If events 1A, 1C, and 1D are reported to the RNC, the target cell can be added to the active set only when CPICH Ec/No is gre
This parameter is used to set a baseline for the quality of the radio links to be added. The current events of soft handovers are
more downlink resources are occupied and more TPC errors are caused, and the soft handover performance is worsened. Th
This parameter should be adjusted, based on the planned Ec/No that the cell soft handover area is expected to reach. If this p
the probability for adding a neighboring cell to the active set increases. In this case, however, the service quality of the cell to b
Maximum number of cells in an active set. This parameter is used to achieve the balance between the signal quality in the SH
several cells. This increases the amount of data to be processed and lowers the system performance. To reduce intra-frequen
decrease in cells in the active set can reduce the consumption of system resources.
Threshold of the quality of the cell reporting event 1F for triggering blind handover. The blind handover is triggered only when
This parameter is used to raise the success rate of blind handovers. If all the signals in the cell reporting event 1F are of poor
This parameter specifies the interval between intra-frequency measurement reports for Load Reshuffling (LDR) blind handove
Used in the algorithm of the load reshuffling (LDR) intra-frequency blind handover. This parameter specifies the number of the
measurement reports that fulfill the quality criterion for blind handover. If the UE reports an unqualified measurement report, th
ID of an RNC
Unique ID of a cell
Unique RNC ID of a neighboring cell
Unique ID of a neighboring cell
Neighboring cell oriented CIO.

This parameter specifies the neighboring cell oriented Cell Individual Offset (CIO). The sum of the value of this parameter, the
used for moving the border of a cell. In the case of an event-based intra-frequency measurement or inter-RAT measurement, t
parameter when evaluating an inter-frequency measurement event.
In the case of a periodical inter-frequency measurement or inter-RAT measurement, the RNC determines whether to initiate a
Determines whether event 1A threshold is affected when the cell is added to the active set. If this parameter is set to "NOT_AF
set to "AFFECT", the relative threshold of event 1A is affected when the cell is added to the active set. That is, the cell signals
Flag of whether adding a cell into the active set will affect the relative threshold of the event 1B.
This parameter is a flag of whether adding the cell into the active set will affect the relative threshold of the event 1B NOT_AFF
the relative threshold of the event 1B. The cell signal will not affect the UE evaluate whether event 1B should occur.
Cell offset used for CPICH RSCP measurement value in cell selection or reselection when the UE is in idle mode.
Offset of neighboring cell CPICH measurement value. This parameter is used for RSCP measurement. The offset is subtracte
(RNP) based on the actual network. If this parameter is set to a greater value, the probability for cell reselection reduces.
Cell offset used for CPICH Ec/No measurement value in cell selection or reselection when the UE is in idle mode.
Offset of neighboring cell CPICH measurement value. This parameter is used for Ec/No measurement. The offset is subtracte
(RNP) based on the actual network.
Cell offset used for CPICH RSCP measurement value in cell selection or reselection when the UE is in connected mode. Durin
cell reselection. In handover algorithms, this parameter is used for moving the border of a cell. This parameter can be configur
Cell offset used for CPICH Ec/No measurement value in cell selection or reselection when the UE is in connected mode. Durin
cell reselection.In handover algorithms, this parameter is used for moving the border of a cell. This parameter can be configure

Cell offset used for CPICH Ec/No measurement value in HCS cell selection.
If this parameter is set to a greater value, the probability for cell reselection reduces. If this parameter is set to a smaller value,

Priority of neighboring cells. The priority assigned to a neighboring cell is valid only when this parameter is set to "TRUE". The
neighboring cell with priority 2.
Indicator of MBMS neighboring cell
Name of the NodeB
Seed of the pseudo-random sequence generator. It can prevent idle period of different NodeBs from overlapping.
Identifies an operator.
Identifies a matching record.
Specifies the protocol that applies to the service.
Specifies the match type in the matching record.
Specifies the IP address in the matching record. The IP address cannot be all 0s.
Specifies the IP mask in the matching record. The IP mask cannot be all 0s.
Specifies the port No. in the matching record.
Specifies the type of the protocol that is applied to the matching record. Only the TCP and UDP are supported.
Specifies the priority of the traffic.
Subrack No
CPUS/MPU subsystem slot No
Represent an index for a Neighboring BSC.

Indicating whether the Neighboring BSC is in the same RNC.
Subrack No
CPUS/MPU subsystem slot No
Subsystem No. of the queried board
The master subrack No.of Neighboring BSC.
The master CPUS/MPU slot No. of neighboring BSC.
Subsystem No. of the queried board
The times of resending the reset message to CN after the response is not received upon the expiry of the timer.
A timer used to wait for the reset response from CN.
A timer used to respond to CN reset.
CN protection timer.
CN flow control timer (short). The OVERLOAD message received repeatedly in this period will be discarded.
CN flow control timer (long). If the OVERLOAD message is not received in this period, the traffic volume will be increased by a
RRC Report KPI Alarm Switch
The period of KPI alarm check, the period must be a multiple of five minutes.
Threshold of RRC connection setup successful ratio per CPUS to report KPI alarm. In a checking period, if the RRC connectio
The minimum number of RRC connection request per CPUS to report KPI alarm. In a checking period,if the number of RRC co
Threshold of AMR RAB setup successful ratio per CPUS to report KPI alarm. In a checking period, if the AMR RAB setup succ
The minimum number of AMR RAB establish request per CPUS to report KPI alarm. In a checking period,if the number of AM
Threshold of VP RAB setup successful ratio per CPUS to report KPI alarm. In a checking period, if the VP RAB setup success
The minimum number of VP RAB establish request per CPUS to report KPI alarm. In a checking period,if the number of VP RA
Threshold of HSDPA RAB setup successful ratio per CPUS to report KPI alarm. In a checking period, if the HSDPA RAB setup
The minimum number of HSDPA RAB establish request per CPUS to report KPI alarm. In a checking period,if the number of H
Threshold of HSUPA RAB setup successful ratio per CPUS to report KPI alarm. In a checking period,if the HSUPA RAB setup
The minimum number of HSUPA RAB establish request per CPUS to report KPI alarm. In a checking period,if the number of H
Threshold of PS RAB setup successful ratio per CPUS to report KPI alarm. In a checking period, if the PS RAB setup success
The minimum number of PS RAB establish request per CPUS to report KPI alarm. In a checking period,if the number of PS RA
Threshold of AMR call drop ratio per CPUS to report KPI alarm.In a checking period, if the AMR call drop ratio is higher than th
The minimum number of AMR call release per CPUS to report KPI alarm.In a checking period, if the number of AMR call relea
Threshold of VP call drop ratio per CPUS to report KPI alarm. In a checking period, if the VP call drop ratio is higher than this t
The minimum number of VP call release per CPUS to report KPI alarm.In a checking period, if the number of VP call release is
Threshold of PS call drop ratio per CPUS to report KPI alarm. In a checking period, if the PS call drop ratio is higher than this t
The minimum number of PS call release per CPUS to report KPI alarm.In a checking period, if the number of PS call release is
CPUS KPI self-healing control switch:

SPU_KPI_AUTOCURE_SWITCH: Whether CPUS KPI self-healing is enabled on the RNC.
Threshold for self-healing triggered by abnormal KPI success rate.
Minimum PLMN tag value corresponding to a LAC. It is defined by the operator. For detailed information of this parameter, ref
Maximum PLMN tag value corresponding to a LAC. It is defined by the operator. For detailed information of this parameter, re
Sharing Network Area Code.

Identifying a location area within the PLMN of GSM-MAP type. It is defined by the operator. H'0000 and H'FFFE are reserved.
If congestion is triggered by multiple resources such as credit and code at the same time, the congestion of resources specifie
IUBLDR refers to processing of LDR action trigged by Iub bandwidth. CREDITLDR refers to processing of LDR action trigged
The values above represent the following algorithms:
NODEB_CREDIT_LDR_SWITCH: NodeB credit congestion control algorithm. This is an RNC-oriented algorithm. When NodeB
LCG_CREDIT_LDR_SWITCH: Local cell group credit congestion control algorithm. This is an RNC-oriented algorithm. When
LC_CREDIT_LDR_SWITCH: Local cell credit congestion control algorithm. This is an RNC-oriented algorithm. When the local
If NODEB_CREDIT_LDR_SWITCH, LCG_CREDIT_LDR_SWITCH and LC_CREDIT_LDR_SWITCH are selected, the corresp
The switch should be enabled to perform flow control on Iub links. If no congestion occurs in the NCP links on the Iub interface
congested links as soon as possible.
Identifying the period of the Intra-frequency load balance algorithm. When the cell load is high, the cell PCPICH TX power can
Identifying the potential user control period. When the cell load is high, the cell selection and reselection can be periodically m
Identifying the period of the LDR execution. When basic congestion occurs, execution of LDR can dynamically reduce the cell
the previous result is displayed in LDM. The higher the parameter value is, the more likely this problem can be prevented. If th
The LDR algorithm aims to slowly reduce the cell load and control the load below the admission threshold, each LDR action ta
when the L3 filter coefficient is set to 6), so the parameter value should be higher than 8s.
Identifying the period of the OLC execution. When overload occurs, execution of OLC can dynamically reduce the cell load. W
to the step-function signals is about 2.8s, namely that the system can trace the load control effect about 3 s later after each loa
OlcPeriodTimerLen along with ULOLCFTFRstrctUserNum, DLOLCFTFRstrctUserNum, ULOLCFTFRSTRCTTimes, DLOLCFT
overload. If the OLC period is excessively short, unnecessary adjustment may occur before the previous OLC action has taken
This parameter specifies the interval at which the RNC determines the fairness between the R99 BE service rate and HSUPA
Period of RTWP-based intra-frequency load balancing adjustment. When RTWP is high, CPICH transmit power is periodically
L3 filtering coefficient. The larger the value of this parameter, the stronger the smoothing effect and the higher the anti-slow-fa
If you set this parameter to TEN_MSEC, use [UL basic meas rprt cycle,Unit:10ms] to specify the measurement report period. I
UL basic common measurement report cycle. For detailed information of this parameter, refer to 3GPP TS 25.433.
If you set this parameter to TEN_MSEC, use [DL basic meas rprt cycle,Unit:10ms] to specify the measurement report period. I
DL basic common measurement report cycle. For detailed information of this parameter, refer to 3GPP TS 25.433.
Period common measurement protection timer coefficient. Timer length of common measurement report protection = max (100
time exceeds the timer length of common measurement report protection, the common measurement is faulty and a new one
Length of smoothing filter window of intra-frequency load balancing (LDB).
Length of smoothing filter window of potential user control (PUC).
Length of smoothing filter window of uplink LDR.
Length of smoothing filter window of downlink LDR.
Length of smoothing filter window of uplink OLC.
Length of smoothing filter window of downlink OLC.
Length of smoothing filter window of uplink CAC.
Length of smoothing filter window of downlink CAC.
If you set this parameter to TEN_MSEC, use [HSDPA need pwr meas cycle,Unit:10ms] to specify the measurement report per
HSDPA power requirement measurement report period For detailed information of this parameter, refer to 3GPP TS 25.433.
Length of smoothing filter window of HSDPA power requirement.
If you set this parameter to TEN_MSEC, use [HSDPA bit rate meas cycle,Unit:10ms] to specify the measurement report period
This parameter specifies the HSDPA bit rate measurement report period. For detailed information of this parameter, refer to 3G
Length of smoothing filter window of HSDPA bit rate.
Max allowed number of continuous invalid measurement reports. For detailed information of this parameter, refer to 3GPP TS
If you set this parameter to TEN_MSEC, use [UL OLC meas rprt cycle,Unit:10ms] to specify the measurement report period. If
Measurement report period of event E triggered by UL OLC. For detailed information of this parameter, refer to 3GPP TS 25.4
UL OLC trigger hysteresis.This parameter can avoid touching off OLC event continually.
If you set this parameter to TEN_MSEC, use [DL OLC meas rprt cycle,Unit:10ms] to specify the measurement report period. If
Measurement report period of event E triggered by DL OLC. For detailed information of this parameter, refer to 3GPP TS 25.4
DL OLC trigger hysteresis.This parameter can avoid touching off OLC event continually.
This parameter specifies the HSUPA bit rate measurement report period. For detailed information of this parameter, refer to 3G
This parameter specifies the HSUPA bit rate measurement report period. For detailed information of this parameter, refer to 3G
Length of smoothing filter window of HSUPA bit rate.
Filter length used for calculating RTWP
Name of the NodeB
This parameter specifies the index that uniquely identifies an LTE cell.
This parameter specifies the cell name that uniquely identifies an LTE cell.
This parameter is used to uniquely identify an LTE cell in the PLMN. For macro base stations, EutranCellId consists of eNodeB
This parameter uniquely identifies the country that an LTE cell belongs to.
This parameter uniquely identifies the network that an LTE cell belongs to.
This parameter specifies Tracking Area Code (TAC) of a cell. In principle, base stations in a certain area are managed by an M
This parameter specifies the operator group that an LTE cell belongs to.
This parameter specifies the physical cell identity of an LTE cell. For detailed description of the parameter, see 3GPP TS 25.3
This parameter specifies the frequency band that an LTE cell is in. For detailed description of the parameter, see 3GPP TS 36
Band1:Frequency Range(0-599)
This parameter specifies the downlink frequency used by an LTE cell. For detailed description of the parameter, see 3GPP TS
This parameter specifies whether an LTE cell supports PS handover. When this parameter is set to SUPPORT, the RNC, CN
Whether an LTE cell is in the blacklist. If this parameter is set to True, information about the LTE cell is not contained in a MEA
handover to the LTE cell. If this parameter is set to False and the LTE cell is configured as a neighboring cell, handover to the
ID of an RNC
Unique ID of a cell
This parameter specifies the index that uniquely identifies an LTE cell.
A timer used to alarm for no mbms data for MBMS traffic.
mobile country code of the RNC.
mobile network code of the RNC.
MBMS Service Identity.
Maximum transmit power on a FACH.

This parameter specifies the minimum coverage percentage of the MTCH corresponding to the RAB priority of 0. When the ce
25.346.
This parameter specifies the minimum coverage percentage of the MTCH corresponding to the RAB priority of 15. When the c
25.346.
A positive value relative to Time of arrival window endpoint (ToAWE). It indicates the startpoint of the arrival time window for a
A positive value relative to Latest Time of Arrival (LToA). It indicates the endpoint of the arrival time window for a downlink dat
MBMS performance channel index
This switch determines whether to take statistics of the performance based on the MBMS channel. One MBMS service is defin
This parameter define MBMS service ID in PLMN ID .
ON denotes enabling of the MBMS function; OFF denotes disabling of the MBMS function.
ON denotes enabling of the MBMS Iub transmission resource sharing function; OFF denotes disabling of the MBMS Iub transm
This parameter specifies whether to add the MSCH logical channel on the SCCPCH. When one MTCH logical channel is carri
This switch specifies whether to add the MSCH logical channel on the SCCPCH. When multi-MTCH logical channels are carrie
This parameter defines the switch of service distribution and load balancing algorithm. If SERVICE-BASED is selected, only lo
will be automatically adjusted to SERVICE-BASED or LOAD-BASED according the load status of current cell.
This parameter defines the load difference threshold between 3G cell and 2G cell when CS service is distributed to 2G. If the l
This parameter defines the load difference threshold between 3G cell and 2G cell when PS service is distributed to 2G. If the l
This parameter defines the period of the measurement reporting from BSC to RNC.
If the switch is ON, the load state of target 2G cell will be considered during Non-covered InterRat handover procedure. If the s
If the switch is ON, the load difference between 3G cell and target 2G cell will be considered during the load-base handover. If
This parameter defines the adjustment coefficient of load value of 2G cell, which used when load value of 2G cell is compared
If the switch is ON, the NACC procedure does not require the support of the CN. Instead, the GERAN (P) SI is sent through th
This argument is used as a factor involved in SERVICE-BASED and LOAD-BASED algorithms mentioned in the argument Mb
be.
This argument is used as a factor involved in SERVICE-BASED and LOAD-BASED algorithms mentioned in the argument Mb
RRC: SERVICE-BASED or LOAD-BASED algorithm is only implemented on RRC connection phase; RAB: SERVICE-BASED
This parameter specifies the coefficient of modification period of the MCCH.
This parameter specifies the coefficient of access period of the MCCH.
This parameter specifies the coefficient of repetition period of the MCCH.

When the measurement-based DRD is performed, this parameter is used to determine whether the DRD retry for blind handov
If this parameter is set to "ON", the DRD retry for blind handover is performed in aperiodic mode.
If this switch is set to "OFF", the DRD retry for blind handover is not performed in aperiodic mode.
Specifies the time length of the measurement-based DRD periodic retry timer. After the service is set up or the data reconfigur
periodic retry timer, initiate an inter-frequency measurement for the DRD inter-frequency neighboring cell, and initiate the chan
subscribers to re-access the cell with a high priority becomes low. If this parameter is set to a smaller value, the probability for
Interval between sending of periodic measurement reports.

This parameter has impact on the Uu signaling flow. If this parameter is set to a small value, the RNC may have high load whe
RSCP Threshold for the target cell. This parameter is used to estimate the signal quality of the periodic reports.The DRD is trig
Ec/No Threshold for the target cell. This parameter is used to estimate the signal quality of the periodic reports. The DRD is tri
order to increase the successful rate of handover, inner protection mechanism keep Ec/No of target cell larger than -16.
Number of retry periods in the interval between a failure of a measurement-based DRD re-attempt and the initiation of the nex
with a high priority becomes high; however, the performance is greatly affected. Note: The process of a measurement-based D
retries the access to a cell in the reported DRD cell list. The process ends until the cell access succeeds.
This parameter defines the timer length for inter-frequency measurement.
The interval between two reports is the configured value.

This parameter has impact on the Uu signaling flow. If the interval is too short and the frequency is too high, the RNC may hav
Indicating whether setting MGWTST Switch on.
MGWTST user IMSI in a number segment.
This parameter describes Fach Max Power.
This parameter specifies whether to apply Robust Header Compression (ROHC) on the MTCH. The value TRUE indicates to a
Protocol type which supports ALG
ALG switch.
The time to live before ALG becomes invalid.
Ethernet port
NAT resouce pool index
Start IP address after NAT
End IP address after NAT

MAX port number after NAT.
MIN port number after NAT.
NAT switch.
Switches for the reliability algorithm.
1) RELIABILITY_CELL_SELFCURE_SWITCH (Cell Selfcure Switch): When this switch is turned on, automatic cell reestablish
2) CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH(Neighboring Cell Status Change Not Update SIB Switch): When the switch
to be turned off after the addition.
Switches for system performance enhancement.
1) PERFENH_R99_BRDCSTHSPA_SWITCH (Neighboring Cell HSPA Capability Broadcast Switch of R99 Cells): When this s
NBM algorithm reserved switch 0. The switch is reserved for further change request use.
NBM algorithm reserved switch 1. The switch is reserved for further change request use.
NBM algorithm reserved U32 para 0. The para of 32 bits is reserved for further change request use.
Name of the NodeB

Measurement start time (HH:MM:SS)
Period of node synchronization
Represent an index for a Neighboring BSC.
No. of the subrack.
No. of the slot of the board.
Controls whether the subsystem in a certain subrack supports the detection function of intra-frequency missing neighboring ce
The value "ON" indicates that the subsystem in a certain subrack supports the detection function of intra-frequency missing ne
Controls whether the subsystem in a certain subrack supports the detection function of inter-frequency missing neighboring ce
The value "ON" indicates that the subsystem in a certain subrack supports the detection function of inter-frequency missing ne
Controls whether the subsystem in a certain subrack supports the detection function of inter-RAT missing neighboring cells.
The value "ON" indicates that the subsystem in a certain subrack supports the detection function of inter-RAT missing neighbo
Name of the NodeB
When the NCP/CCP is based on ATM, set Bearing link type to SAAL. When the NCP/CCP is based on IP, set Bearing link typ
Link Modify Type.

When the NCP is ATM to ATM-IP, this parameter is set to ATMTODUAL. When the NCP is based on IP to ATM-IP, set this pa
UNI link number
Name of the NodeB
NodeB ID
Number of the EPS subrack managing the subsystem to which the NodeB belongs
UMTS XPU board slot Number
UMTS CPUS where the NodeB is located.
Transport type of the Iub interface
Indicating whether the Iub interface supports IP hybrid transport.
This parameter specifies the round-trip transport delay of Iub interface when the transmission mode is ATM transmission or of
Indicating whether the Iub interface supports satellite transmission

Protocol version of the NodeB
Indicating the resource management mode
If the value is ON, the RNC sends a message containing the extended IMSI information element to the NodeB for the CDT tra
This parameter specifies the NodeB host type in RNC Node Redundancy function. If the parameter value is SINGLEHOST, th
By default, the NodeB is managed by the host RNC. When the host RNC fails, the physical NodeB is managed by the seconda
This parameter specifies the RNC ID of the peer RNC in the RNC POOL.
ID configured in another RNC of the RNC POOL. In RNC Node Redundancy function, the two RNCs form an RNC POOL and
This parameter specifies the sharing type of a NodeB. The value "DEDICATED" indicates that all cells of the NodeB belong to
to multi-operators.
Whether a NodeB supports Dynamic Spectrum Sharing (DSS)
Name of the NodeB

IUB_LDR (Iub congestion control algorithm): When the NodeB Iub load is heavy, users are assembled in priority order among
NODEB_CREDIT_LDR (NodeB level credit congestion control algorithm): When the NodeB level credit load is heavy, users ar
LCG_CREDIT_LDR (Cell group level credit congestion control algorithm): When the cell group level credit load is heavy, users
IUB_OLC (Iub Overload congestion control algorithm): When the NodeB Iub load is Overload, users are assembled in priori
To enable some of the algorithms above, select them. Otherwise, they are disabled.
Maximum number of HSDPA users of the NodeB. If the HSDPA user access is rejected by the NodeB, you can infer that the H
Maximum number of HSUPA users of the NodeB. If the HSUPA user access is rejected by the NodeB, you can infer that the H
When the dynamic CE algorithm on NodeB is applied, the CE consumption of HSUPA UE is based on the GBR. When the dyn
reduction. If the CE consumption of HSUPA UE is based on the MBR,the CE LDR will select HSUPA users to do data rate red
Reserved Parameter1.
NodeB ID
The first electrical serial number of NodeB
This parameter specifies whether NodeB used the electronic serial number 2, or not.
The second electrical serial number of NodeB
NodeB transmission port type
IP address of NodeB ETH/TRUNK port

Subnet mask of NodeB ETH/TRUNK port
This parameter specifies whether to turn on NodeB gateway IP switch, or not.
NodeB ID
Transmission type of NodeB
When the operation and maintenance channel of NodeB is operating in the IP transmission mode, this parameter indicates the
When the operation and maintenance channel of NodeB is operating in the IP transmission mode, this parameter indicates the
Subrack number of the RNC interface board interworking with NodeB when the NodeB operation and maintenance channel wo
Slot number of the RNC interface board interworking with NodeB when the NodeB operation and maintenance channel works
This parameter specifies whether to bind the logical port,or not.
Number of the logical port for the NodeB operation and maintenance channel in the IP transmission mode
When the operation and maintenance channel of NodeB is operating in the ATM, this parameter indicates the address of the o
When the operation and maintenance channel of NodeB is operating in the ATM, this parameter indicates the mask of the ope
When the operation and maintenance channel of NodeB is operating in the ATM, this parameter indicates the subrack numbe
When the operation and maintenance channel of NodeB is operating in the ATM, this parameter indicates the slot number of t
Specified Vlan enabling flag
VLAN priority
Name of the NodeB

BERATERED: Channels are reconfigured for the BE service to reduce rate.
QOSRENEGO: The renegotiation on the QoS of the uncontrollable real-time service is performed to reduce service QoS.
CSINTERRATSHOULDBELDHO: The inter-RAT SHOULDBE load handover of the CS domain is performed. For details, refer
CSINTERRATSHOULDNOTBELDHO: The inter-RAT SHOULDNOTBE load handover of the CS domain is performed.
PSINTERRATSHOULDNOTBELDHO: The inter-RAT SHOULDNOTBE load handover of the PS domain is performed.
Number of RABs selected in a DL LDR BE traffic rate reduction. In the actual system, this parameter can be set on the basis o
Number of RABs selected in a DL LDR uncontrolled real-time traffic QoS renegotiation. The target subscribers of this paramet
Number of users selected in a DL LDR CS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a DL LDR PS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a DL LDR CS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
Number of users selected in a DL LDR PS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p

BERATERED: Channels are reconfigured for the BE service to reduce rate.
QOSRENEGO: The renegotiation on the QoS of the uncontrollable real-time service is performed to reduce service QoS.
CSINTERRATSHOULDBELDHO: The inter-RAT SHOULDBE load handover of the CS domain is performed. For details, refer
CSINTERRATSHOULDNOTBELDHO: The inter-RAT SHOULDNOTBE load handover of the CS domain is performed.
Number of RABs selected in a UL LDR BE traffic rate reduction. In the actual system, this parameter can be set on the basis o
Number of RABs selected in a UL LDR uncontrolled real-time traffic QoS renegotiation. The target subscribers of this paramet
Number of users selected in a UL LDR CS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a UL LDR PS domain inter-RAT SHOULDBE load handover. The target subscribers of this param
Number of users selected in a UL LDR CS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
Number of users selected in a UL LDR PS domain inter-RAT SHOULDNOTBE load handover. The target subscribers of this p
Threshold of SF reserved in uplink credit LDR. The uplink credit LDR is triggered when the SF factor corresponding to the upli
easier the user experience is affected. A lower code resource LDR trigger threshold, however, causes a higher admission suc
Threshold of SF reserved in downlink credit LDR. The downlink credit LDR is triggered when the SF factor corresponding to th
and the easier the user experience is affected. A lower code resource LDR trigger threshold, however, causes a higher admiss
The threshold of the reserved SF is used for judging the uplink credit state for TTI switchover decision. When uplink credit is lo
NodeB ID
Uniquely identifying the name of a NodeB
Name of the NodeB
Number of RABs selected in one DL traffic release.One RAB represents one service of a single user
Number of RABs selected in one UL traffic release.
ID of an RNC
Neighboring relation type to be removed
Identifying a Network resourse:
1. The NRI numbers of CS domain and PS domain are independent from each other.
2. If multiple pool areas overlap, the NRI uniquely identify all the CN nodes connected to it.
3. A CN node can have multiple NRIs. In one pool area, however, an NRI can only correspond to one CN node.
Neighboring RNC ID.

Indicating whether to trigger soft handover cross the Iur interface between the RNC and the neighboring RNC:
1) CS_SHO_SWITCH. Indicating whether to trigger soft handover for CS cross the Iur interface.
2) HSPA_SHO_SWITCH. Indicating whether to trigger soft handover for HSPA cross the Iur interface.
3) NON_HSPA_SHO_SWITCH. Indicating whether to trigger soft handover for PS(R99) cross the Iur interface.
Indicating whether to trigger hard handover cross the Iur interface between the RNC and the neighboring RNC.
Indicating whether to support CS, PS or both domains.
Indicating whether to config neighbouring RNC's DSP index.
Protocol version supported by the neighboring RNC.
Protection timer used in case of DSP intermittent at the neighboring RNC.
Indicating whether to support establishing IUR-CCH between the RNC and the neighboring RNC.
32-bit unsigned integer.
1) DL_DCCH_SWITCH. When it is checked, SRNC will include the IE "RB Id for handover message" in the IE "SRNS Relocati
protecting the message if applicable.
2) IUR_TRG_SWITCH. When it is checked, relocation execution may trigger as an implementation option from the Iur interface
The transfers bearer type of Iur interface.
Indicating whether to replace relocation procedure with DSCR procedure between the RNC and the Neighboring RNC for PS B
Indicating whether to support Hsdpa over Iur interface of the Neighboring RNC.
Indicating whether to support Hsupa over Iur interface of the Neighboring RNC.
Indicating whether the Iub privated IEs of User Plane exist in Iur message between the RNC and the Neighboring RNC.
Indicates whether degrade HSPA to DCH procedure is performed before the relocation procedure when the CS services are c
relocation procedure.
1) RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:The switch is turned on: When receiving a handover/relocation req
SRNC considers the RNC that controls the cell as the target RNC.
The switch is turned off: When receiving a handover/relocation request from the SRNC, the DRNC sends the SRNC a handov
Indicating whether the Iub privated IEs of Control Plane exist in Iur message between the RNC and the Neighboring RNC.
Neighboring RNC ID.
URA ID.
This parameter specifies the index of CN operator.
To set the status of RNC Offload function
The action for Non-DT RAB to use offload function
The action for registered APNs to take Offload function
To predefine Rate for Gi bandwidth allocation
To set the status of RNC Offload Charge Switch

The action for registered APNs to take Offload function

Indentify the unique APN of one operator. The parameter can only be deleted, but not be modified.

This parameter specifies the APN
Type Allocation Code (TAC) is a part of the International Mobile Station Equipment Identity (IMEI). The TAC is used to identify
Description UE type.

Indicates the start of an IMSI range. For UEs with IMSIs ranging from this IMSI number (IMSIStart) to IMSIEnd, if their PS serv
be transmitted on the Gi interface. For UEs with IMSIs beyond the IMSI range, the offload function is unavailable.
Indicates the end of an IMSI range. For UEs with IMSIs ranging from IMSIStart to this IMSI number (IMSIEnd), if their PS serv
be transmitted on the Gi interface. For UEs with IMSIs beyond the IMSI range, the offload function is unavailable.
The parameter specifies the user priority, such as a GOLDEN user.
The parameter specifies the traffic type of a RAB, such as a Background traffic.
This parameter specifies feature mode of operators in the CS domain. You should configure the network resource identifier (N
This parameter specifies feature mode of operators in the PS domain. You should configure the network resource identifier (N
This parameter specifies the value of the NAS Node Selection Function (NNSF) timer for CS traffic paging. For the IMSI pagin
stops the NNSF protection timer.
Network Resource Identity(NRI) length for CS domain.
Network Resource Identity(NRI) length for PS domain.
NullNRI VALUE indicates that the ue assigns load to other CN nodes ,when NNSF selects other CN nodes.
Indicating whether the CS domain permits the CN information to update .
Indicating whether the PS domain permits the CN information to update .
Cs domain Information Update protection timer.
Ps domain Information Update protection timer.
When RAN Sharing Supported, RNC can configure multi-plmn.
This parameter determines whether the RNC supports the MOCN function. When MOCN Supported, RNC can configure multi
This parameter specifies whether intra-RAT handover of the UE among different operators is allowed.
This parameter specifies whether inter-RAT handover of the UE among different operators is allowed.
This parameter specifies the default operator that RNC chooses in the MOCN cell. The value 255 means that no default opera
MOCN Control Switch.

1) COMM_MOCN_NRI_GLOBAL_CONFIG_MODE_SWITCH: When the switch is selected, the NRI of any CN node in the RN
2) COMM_MIB_MULTI_PLMN_LIST_ALLOWED_SWITCH: When the switch is selected, the operator information configured i
Index of the CN operator
Method of determining an HSDPA service rate when the differentiated HSPA service based on SPI weight function is enabled.
smaller one between MBR and the peak rate corresponding to the UE HSDPA category is used. Value Max indicates that the
Method of determining an HSUPA service rate when the differentiated service based on SPI weight function is enabled. Value
one between MBR and the peak rate corresponding to the UE HSUPA category is used. Value Max indicates that the greater
Traffic class. This parameter only applies to interactive and background services, as the Scheduling Priority Indicator (SPI) of
Traffic Handling Priority (THP) class that the THP priority is mapped to. This parameter is valid for only interactive services. Th
Scheduling priority of interactive and background services. Value 11 indicates the highest priority, while value 2 indicates the l
Specifies the weight for service scheduling priority. This weight is used in two algorithms. In scheduling algorithm, it is used to
get more Iub bandwidth, respectively.
Whether to configure SPI weight based on the value range of an HSPA service rate. Value FALSE indicates that the SPI weig
scheduling priority. "SpiWeigth" will not be used for HSPA service when this parameter set to TRUE.
SPI weight corresponding to HSDPA data rate range 1. When the data rate of an HSDPA service is smaller than or equal to "D
UOPERCAPARATERANGE" command.
SPI weight corresponding to HSDPA data rate range 2. When the data rate of an HSDPA service is greater than "DlRateThres
running the "SET UCAPARATERANGE" or "ADD UOPERCAPARATERANGE" command.
SPI weight corresponding to HSDPA data rate range 10. When the data rate of an HSDPA service is greater than "DlRateThre
SPI weight corresponding to HSUPA data rate range 1. When the data rate of an HSUPA service is smaller than or equal to "U
SPI weight corresponding to HSUPA data rate range 2. When the data rate of an HSUPA service is greater than "UlRateThres
SPI weight corresponding to HSUPA data rate range 10. When the data rate of an HSUPA service is greater than "UlRateThre
Priority class associated with PS interactive service whose traffic handling priority is 1. The priority class are High, Medium and
Priority class associated with PS interactive service whose traffic handling priority is 10. The priority class are High, Medium an
Traffic class which includes Best Effort(BE) and PTT. BE services comprise interactive services, background services, and IMS
Bearer type of the service. R99 indicates that the service is carried on a non-HSPA channel. HSPA indicates that the service i
Uplink guaranteed bit rate (GBR) of the BE service. GBR is the minimum bit rate that the system can guarantee for the service
Downlink guaranteed bit rate (GBR) of the BE service. GBR is the minimum bit rate that the system shall guarantee for the ser
Traffic class
Defines the happy bit rate of the best effort (BE) service with different user priorities(user priorities can be set by parameter Us
will be decreased. When this parameter is set to zero, it indicates that NodeB will not adjust the HS-DSCH scheduling priority.
User_priority corresponding to Allocation/Retention priority 1.

Reference used to determine which priority is arranged first in the priority sequence.
If the ARP is preferably used, the priority sequence is gold > silver > copper. If the ARPs are all the same, the TrafficClass is u
If the TrafficClass is preferably used, the priority sequence is conversational > streaming > interactive > background. If the Tra
Decide which carrier is prior when ARP and TrafficClass are both identical.
Uniquely identifying a PCCPCH in a cell
Uniquely identifying an SCCPCH corresponding to a paging indication channel in a cell
Uniquely identifying a PCH in a cell
The rate matching factor of a transport channel.For detailed information of this parameter, refer to 3GPP TS 25.212.
Start point of the arrival window of DL data frame. Normally, it is forecasted that a DL data frame will arrive after the time spec
End point of the arrival window of DL data frame. Normally, it is forecasted that a DL data frame will arrive before the time spe
Offset of the PCH transmit power from the PCPICH transmit power in a cell. For detailed information of this parameter, refer to
Uniquely identifying a PCH in a cell
This parameter defines the number of the transport formats corresponding to the above "RLC Size" in the TF set.
This parameter defines the number of the transport blocks corresponding to the TF 1 of the above "RLC Size" in the TF set. Th
This parameter defines the number of the transport blocks corresponding to the TF 2 of the above "RLC Size" in the TF set.
Uniquely identifying a PCPICH in a cell
PCPICH transmit power of a cell that is enabled with Dynamic Spectrum Sharing (DSS) and in small DSS coverage.
Whether to enable periodical RTT locating at the RNC
Whether to forcibly transfer direct locating request to periodical locating request.

Number of reports for each periodical locating request transferred from direct locating requesting on the Iu interface.
Reporting interval for the periodical locating request transferred from direct locating requesting on the Iu interface.
Uniquely identifying a PICH in a cell
Indicating the number of PIs contained in each frame of the PICH For detailed information of this parameter, refer to 3GPP TS
Difference between the transmit power of PICH and that of PCPICH
Modification type.
Identifying a location area within the PLMN of GSM-MAP type. It is defined by the operator. H'0000 and H'FFFE are reserved.
Identifying a routing area in a location area within the PLMN of GSM-MAP type. It is defined by the operator.
The minimum PLMN value tag corresponding to a LAC or RAC. It is defined by the operator.
The maximum PLMN value tag corresponding to a LAC or RAC. It is defined by the operator.
This parameter specifies re-host policy type for NodeB. The value "REHOSTRIGHTNOW" indicates to perform re-host policy f
The value "REHOSTWHEN" indicates to perform re-host policy for the NodeB at a specific time.
This parameter specifies the delay time. When the RNC recovers from disaster and starts to operate, it performs re-host policy
This parameter specifies the time to execute re-host policy for the primary hosted NodeB, after the RNC recovers from disaste
Uniquely identifying a PRACH in a cell

Sequence Number of an available preamble signature. A maximum of 16 signatures (from signature 0 to 15) can be selected.
Sequence Number of an available sub channel. A maximum of 12 sub channels (from sub channel 0 to 11) can be selected. F
Uniquely identifying a PRACH in a cell.
It defines the mapping of AC 0~9 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.
It defines the mapping of AC 10 to ASCs. For detailed information of this parameter, refer to 3GPP TS 22.011.
Identifying an ASC
Identifying the available signature start index of an ASC. For detailed information of this parameter, refer to 3GPP TS 25.304.
Identifying the available signature end index of an ASC. For detailed information of this parameter, refer to 3GPP TS 25.304.
Identifying the available sub channels of an ASC. When a UE has been accessed to a sub channel, if "AICH Transmission Tim
available sub channel allocated to the PRACH, and a 12-bit data stream is obtained finally. If a bit is 1, the corresponding sub
Bitstring (12) corresponding to the available sub channel allocated to the PRACH, and a 12-bit data stream is obtained finally.
It is used to calculate the corresponding dynamic persist scaling factor for ASC2~ASC7. It is valid for ASC2-ASC7 only and ma
Sequence Number of an available preamble signature. A maximum of 16 signatures (from signature 0 to 15) can be selected.
Sequence Number of an available sub channel. A maximum of 12 sub channels (from sub channel 0 to 11) can be selected. F
This parameter specifies a constant used at calculation of the initial transmit power of the first preamble, to be used in the rand
The formula is as follows: Preamble_Initial_Power = Primary CPICH DL TX power-CPICH_RSCP + UL interference + Constan
measured by UEs, and UL interference is the uplink interference. For detailed information of this parameter, refer to 3GPP TS
The maximum number of preambles transmitted in a preamble ramping cycle. For detailed information of this parameter, refer
The power ramp step of the random access preambles transmitted before the UE receives the acquisition indicator in the rand
Maximum number of bits of the Calculated Transport Format Combination (CTFC) of Transport Format Combination Set (TFC
Number of available PRACH timeslot formats. For detailed information of this parameter, refer to 3GPP TS 25.211.
Sequence number of available PRACH timeslot formats. For detailed information of this parameter, refer to 3GPP TS 25.211.
Uniquely identifying a TFC on the physical channel. The specific parameter value depends on the CTFCSize (2 bits: 0~3, 4 bit
The power offset between the last access preamble and the message control part. The power of the message control part can
This parameter specifies the power assignment factor of the control part. For detailed information of this parameter, refer to 3G
The power occupancy factor of the data part. For detailed information of this parameter, refer to 3GPP TS 25.214.

This parameter specifies a constant used at calculation of the initial transmit power of the first preamble, to be used in the rand
The formula is as follows: Preamble_Initial_Power = Primary CPICH DL TX power-CPICH_RSCP + UL interference + Constan
measured by UEs, and UL interference is the uplink interference. For detailed information of this parameter, refer to 3GPP TS
The power ramp step of the random access preambles transmitted before the UE receives the acquisition indicator in the rand
The maximum number of preambles transmitted in a preamble ramping cycle. For detailed information of this parameter, refer
Uniquely identifying a PSCH in a cell
When detecting that the Ps' Conversational User had no data to transfer for a long time which longer than this timer, the PDCP
After sending release request to RRC layer, if the Conversational Radio Access Bear haven't been released until the Conversa
When detecting that the Ps' Streaming User had no data to transfer for a long time which longer than this timer, the PDCP laye
After sending release request to RRC layer, if the Streaming Radio Access Bear haven't been released until the Streaming se
When detecting that the Ps' Interactive User had no data to transfer for a long time which longer than this timer, the PDCP lay
After sending release request to RRC layer, if the Interactive Radio Access Bear haven't been released until the Interactive se
When detecting that the Ps' Background User had no data to transfer for a long time which longer than this timer, the PDCP la
After sending release request to RRC layer, if the Background Radio Access Bear haven't been released until the Background
This parameter specifies the value of the CELL_PCH inactivity timer for UEs enabled with the Fast Dormancy feature. When d
After sending release request to RRC layer, if the IMS Radio Access Bear for signal haven't been released until the IMS servic
When detecting that the Ps' IMS signal had no data to transfer for a long time which longer than this timer, the PDCP layer wo
This parameter specifies the value of the CELL_DCH inactivity timer for UEs enabled with the Fast Domancy feature. When de
This parameter specifies the value of the CELL_FACH inactivity timer for UEs enabled with the Fast Dormancy feature. When
Switch for fast synchronization at Layer 1. This function enables the UE to synchronize with the UTRAN at Layer 1 both on the
If the parameter is set to ON, the function is supported.
If the parameter is set to OFF, the function is not supported.
Number of attempts to resend PTT paging messages. When a UE receives a PTT paging message, the RNC resends paging
Timer for resending paging messages. To trigger state transition from CELL_PCH/URA_PCH to CELL_DCH, a PTT UE sends
If the RNC fails to receive a CELL UPDATE CONFIRM RESPONSE message from the UE after the timer has expired and the
Number of the RNC attempts to resend CELL UPDATE CONFIRM messages. If the RNC fails to receive a response message
value of the parameter.
Controls whether the state transition of the PTT users is allowed.
When the switch is on, the function that UE RRC state transition(CELL_FACH/CELL_PCH/URA_PCH) is enabled for PTT Use
Controls whether the direct state transition (from CELL_PCH/URA_PCH to CELL_DCH) of the PTT users is allowed.
Interval between the reporting of event 4B and the triggering the state transition of the PTT users from DCH/HSPA to FACH.
When the traffic of the PTT user in CELL_DCH state is lower than the event 4B threshold, this timer is started and the UE repo
If the UE continues to report the event 4B when the timer works, the RNC determines that the UE is in low activity state.
If the UE remains in low activity state after the timer expires, the state of the UE is changed from DCH/HSPA to the FACH.
If this parameter is set to a small value, whether the UE is in low activity state cannot be determined. If this parameter is set to
Interval between the reporting of event 4B and the triggering of the state transition of the PTT users from CPC_HSPA state to
If the UE does not report the event 4B when the timer works, the RNC determines that the UE is in low activity state.
If the UE remains in low activity state after the timer expires, the state of the UE is changed from CPC_HSPA to FACH.
Interval between the reporting of event 4B and the triggering of the state transition of the PTT users from DCH/HSPA to E_FA
If the UE remains in low activity state after the timer expires, the state of the UE is changed from DCH/HSPA to E_FACH.
Interval between the reporting of event 4B and the triggering of the state transition of the PTT users from CPC_HSPA to E_FA
If the UE remains in low activity state after the timer expires, the state of the UE is changed from CPC_HSPA to E_FACH.
Threshold for reporting the event 4B in DCH/HSPA.

When the traffic of the PTT user in DCH/HSPA state is constantly lower than this threshold in a period, the UE reports the eve
Period during which the traffic of the PTT user is constantly lower than the event 4B threshold so that the UE reports the even
When the traffic of the PTT user in DCH/HSPA state is constantly lower than the event 4B threshold in this period, the UE repo
Period during which the event 4B is suspended.
After reporting a 4B event triggered by the state transition from DCH/HSPA to CELL_FACH, the UE may report the event 4B a
If this parameter is specified, the system prohibits the UE from reporting the event 4B again during the period when the event
If the parameter value is too small, too many 4B events may be reported, thus increasing the RNC load. If the parameter value
Period in which the E-DCH throughput is measured. To implement the state transition of the PTT users from E-DCH to FACH,
Threshold for reporting the event 4B relevant to the E-DCH throughput.
When the uplink throughput of the PTT user in HSPA state is constantly lower than this threshold in a period, the UE reports th
Number of periods in which the E-DCH throughput of the PTT services are measured. When the E-DCH throughput is lower th
PTT E-DCH Throu Meas Period". By specifying this parameter, the unnecessary throughput events caused by unstable throug
Number of periods during which the event 4B is suspended.
After reporting a 4B event triggered by the state transition from E-DCH to CELL_FACH, the UE may report the event 4B again
If this parameter is specified, the system prohibits the UE from reporting the event 4B again during the "PTT E-DCH2F 4B Pen
Interval between the reporting of event 4B and the triggering the state transition of the PTT users from CELL_FACH to CELL_
When the traffic of the PTT user in CELL_FACH state is lower than the event 4B threshold, this timer is started and the UE rep
If the UE continues to report the event 4B when the timer works, the RNC determines that the UE is in low activity state.
If the UE remains in low activity state after the timer expires, the state of the UE is changed from CELL_FACH to the CELL_PC
Threshold for reporting the event 4B.

When the traffic of the PTT user in CELL_FACH state is constantly lower than this threshold in a period, the UE reports the ev
Period during which the traffic of the PTT user is constantly lower than the event 4B threshold so that the UE reports the even
When the traffic of the PTT user in CELL_FACH state is constantly lower than the event 4B threshold in this period, the UE rep
Period during which the event 4B is suspended.
After reporting a 4B event triggered by the state transition from CELL_FACH to CELL_PCH, the UE may report the event 4B a
If this parameter is specified, the system prohibits the UE from reporting the event 4B again during the period when the event
Threshold for reporting the 4A event.

When the traffic of the PTT user in CELL_FACH state is constantly greater than this threshold in a period, the UE reports the 4
Period during which the traffic of the PTT user is constantly greater than the 4A event threshold so that the UE reports the eve
When the traffic of the PTT user in DCH/HSPA state is constantly greater than the 4A event threshold in this period, the UE re
Threshold for reporting the 4A event.
When the traffic of the PTT user in enhanced CELL_FACH state is constantly greater than this threshold in a period, the UE re
Period after which a UE reports event 4A.

If the traffic of a PTT UE in the enhanced CELL_FACH state is constantly greater than the event 4A threshold in this period, th
Whether the RNC updates traffic measurement parameters before the state of an E_PCH-capable UE using combined PTT se
When the parameter is set to YES, the QoS control algorithm is used for BE services. When the parameter is set to NO, the Q
When the parameter is set to YES, the QoS control algorithm is used for AMR services. When the parameter is set to NO, the
When the parameter is set to YES, the QoS control algorithm is used for VP services. When the parameter is set to NO, the Q
The first action selected by the QoS control algorithm when the UL QoS of BE service deteriorates.If QoS action is RateDegra
The second action selected by the QoS control algorithm when the UL QoS of BE service deteriorates.If QoS action is RateDe
The third action selected by the QoS control algorithm when the UL QoS of BE service deteriorates.If QoS action is RateDegra
Timer to trigger the next QoS enhancement action for UL BE services. This parameter specifies the duration of waiting for the
The timer starts when the BE UL rate adjustment procedure is triggered, and stops when the RNC receives a 6B1/6B2 event o
The first action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDegra
The second action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDe
The third action selected by the QoS control algorithm when the DL QoS of BE service deteriorates.If QoS action is RateDegra
For BE service, When the parameter is set to SINGLE, an UL event 6A1 or 5A can independently trigger the QoS enhanceme
whether to perform 6A1 and 5A measurement is not controlled by the 6A1 and 5A measurement switch.
When the parameter is set to YES, QoS control for DL BE services is based on the TCP and RLC retransmission. When the p
If the parameter is set to YES, QoS control for DL BE services based on RLC retransmission can be performed when the best
Rate adjustment switch of link stability control for UL QoS of AMR services. When the parameter is set to YES, UL rate of AMR
Timer for triggering a second adjustment of the UL AMR mode. This parameter specifies the duration of waiting for the voice q
The UL AMRC rate adjust timer starts when AMRC mode adjustment procedure is triggered, and stops when the next measu
adjustment. The previous AMRC mode adjustment is not effective, and another adjustment is required.
Inter-frequency handover switch of link stability control for UL QoS of AMR services. When the parameter is set to YES, inter-f
Inter-RAT handover switch of link stability control for UL QoS of AMR services. When the parameter is set to YES, inter-RAT h
Rate adjustment switch of link stability control for UL QoS of WAMR services. When the parameter is set to YES, UL rate of W
Timer for triggering a second adjustment of the UL WAMR mode. This parameter specifies the duration of waiting for the voice
stops when the next measurement report is received. If no measurement report is received when the UL AMRC timer expires,
Inter-frequency handover switch of link stability control for UL QoS of WAMR services. When the parameter is set to YES, inte
Inter-RAT handover switch of link stability control for UL QoS of WAMR services. When the parameter is set to YES, inter-RAT
Rate adjustment switch of link stability control for DL QoS of AMR services. When the parameter is set to YES, DL rate of AMR
Inter-frequency handover switch of link stability control for DL QoS of AMR services. When the parameter is set to YES, inter-f
Inter-RAT handover switch of link stability control for DL QoS of AMR services. When the parameter is set to YES, inter-RAT h
Rate adjustment switch of link stability control for DL QoS of WAMR services. When the parameter is set to YES, DL rate of W
Inter-frequency handover switch of link stability control for DL QoS of WAMR services. When the parameter is set to YES, inte
Inter-RAT handover switch of link stability control for DL QoS of WAMR services. When the parameter is set to YES, inter-RAT
Inter-frequency handover switch of link stability control for UL QoS of VP services. When the parameter is set to YES, inter-fre
Inter-frequency handover switch of link stability control for DL QoS of VP services. When the parameter is set to YES, inter-fre
Event 6A1 measurement switch when BeUlEvTrigInd is set to SINGLE for BE service. If this parameter is set to YES, event 6A
Event 5A measurement switch when BeUlEvTrigInd is set to SINGLE for BE service. If this parameter is set to YES, event 5A
UL event 6D measurement switch for BE service. If this parameter is set to YES, event 6D measurement is delivered.
Timer for rejecting rate increase after rate decrease is performed across the Iur interface for BE services. If the best cell is on
Frequency hysteresis of downlink RSCP QoS.
This parameter controls the used frequency thresholds for the inter-frequency and inter-RAT measurement based on QoS.
In event mode, if the inter-frequency and inter-RAT measurement events occurred for the downlink QoS reason, the used freq
The larger the value of the parameter is, the more easily event 2B, inter-frequency handover based on QoS, and event 3A, int
Timer length for downlink QoS measurement.

This parameter controls the time lengths for the inter-frequency and inter-RAT measurement based on QoS.
Timer length for uplink QoS measurement.

This parameter controls the time lengths for the inter-frequency and inter-RAT measurement based on Qos.
This parameter configures the used frequency measurement quantity to trigger the inter-RAT measurement for the purpose of
Ec/No: signal-to-noise ratio
RSCP: received signal code power
CPICH_Ec/NO: the measurement quantity used for event 2D and 2F, with unit of dB
CPICH_RSCP: the measurement quantity used for event 2D and 2F, with unit of dBm
The RNC, in the coverage-based inter-RAT measurement, may configure that the inter-RAT measurement quantity are deliver
the QoS-based inter-RAT measurement to set the used frequency separately. When both the QoS-based and the coverage-ba
When the UE moves to the cell border, and there is a intra-frequency neighboring cell in the moving direction, CPCICH Ec/No
and the quality should be evaluated according to CPCICH RSCP. If the measurement quantity is not properly selected, the ha
Duration when the measured value of AMR keeps fulfilling the 6D measurement condition before the event 6D is triggered. Ev
The measured value is reported after it fulfills the conditions for reporting and for the trigger time specified by this parameter. T
Duration when the measured value of VP keeps fulfilling the 6A1 measurement condition before the event 6A1 is triggered. Th
Duration when the measured value of VP keeps fulfilling the 6B1 measurement condition before the event 6B1 is triggered. Th
Duration when the measured value of VP keeps fulfilling the 6D measurement condition before the event 6D is triggered. The
Duration when the measured value of BE keeps fulfilling the 6D measurement condition before the event 6D is triggered. The
Smooth filtering coefficient for UL measured values. The smooth filtering algorithm is used to avoid random interference in me
Smooth filtering coefficient for DL measured values. The smooth filtering algorithm is used to avoid random interference in me
Duration from when the AMR TX power is beyond the threshold Ea or below the threshold Eb to when the event Ea or Eb is tri
This parameter specifies the reporting period of the event E of the AMR service. The unit of the reporting period can be 10 ms
Duration from when the VP TX power is beyond the threshold Ea or below the threshold Eb to when the event Ea or Eb is trigg
This parameter specifies the reporting period of the event E of the VP service. The unit of the reporting period can be 10 ms o
Duration from when the BE TX power is beyond the threshold Ea to when the event Ea is triggered or from when the BE TX po
This parameter specifies the reporting period of the event E of the BE service. The unit of the reporting period can be 10 ms o
Duration within which the measured power being lower than the threshold is allowed for BE service. This parameter is used to
This parameter specifies the reporting period of the event F of the BE service. The unit of the reporting period can be 10 ms o
Determines whether preemption is supported. When this switch is enabled, the RNC allows privileged users or services to pre
failure in cell resource application.
Indicates whether the MBMS supports resource preemption. When the switch is enabled, the RNC allows the preempting MBM
candidate set. In this case, the cell resources assigned to the MBMS may be preempted by users or services with higher prior
Indicating whether ARP-based preemption between TCs is supported. This switch only has impact on the TC-based priorities.
service is the streaming service and the preempted service is the interactive or background service. 2. The preempting service
Indicating whether queue is supported. When a user initiates a call, if cell resources are insufficient and the user is queue supp
Queue length. The total number of users in queue of each cell should not exceed the value specified in this parameter. When
the queue and access fails. At the same time, the new user joins the queue. 3) If the queue has a user whose priority is lower
Timer length of the queue poll. The queue is polled for every time specified in this parameter. During each poll, all the expired
access and traverse of this queue is stopped. Otherwise, the rest users are traversed until all the unexpired users go through t
Maximum queue time of users. When a user initiates a call, it joins the queue due to cell resource insufficiency. This paramete
When the switch is enabled, users attempting emergency call can preempt the resources from all the accessed users for non e
information element.
Minimum PLMN tag value corresponding to a LAC. It is defined by the operator. For detailed information of this parameter, ref
Maximum PLMN tag value corresponding to a LAC. It is defined by the operator. For detailed information of this parameter, re
Uniquely identifying an RACH in a cell
This parameter defines the rate matching factor of the RACH.
Lower limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and 3GPP TS 25.214 protocols.
Upper limit of random access back-off delay. For details, refer to the 3GPP TS 25.331 and 3GPP TS 25.214 protocols.
The parameter specifies the maximum number of preambles to be used in one preamble ramping cycle. For detailed informati
Uniquely identifying an RACH in a cell
This parameter defines the number of the transport formats corresponding to the above "RLC Size" in the TF set.
This parameter defines the number of the transport blocks corresponding to the TF 1 of the above RLC size in the TF set. The
This parameter defines the number of the transport blocks corresponding to the TF 2 of the above RLC size in the TF set.
This parameter specifies the maximum value that Ec/No can be stepped up in the link quality adjust algorithm for E-FACH.
This parameter specifies the maximum value that Ec/No can be stepped down in the link quality adjust algorithm for E-FACH.
This parameter is used to count the adjusted step of Ec/No in the link quality adjust algorithm for E-FACH.
This parameter specifies the target number of the RLC retransmissions. In the link quality adjust algorithm for E-FACH, When
This parameter specifies the adjustment cycle of Ec/No. This parameter is also used to determine the measurement period of
This parameter specifies the maximum value of Ec/No in the E-FACH Ec/No adjustment algorithm. The formula is y = x * 0.5 -
This parameter specifies the minimum value of Ec/No in the E-FACH Ec/No adjustment algorithm. The formula is y = x * 0.5 -
Traffic class whose RRC redirection parameters are to be set

Whether the RRC redirection algorithm is valid for the specified service. The algorithm is valid only when the RRC direct redire
- OFF indicates that RRC redirection is not allowed.
- Only_To_Inter_Frequency indicates that only RRC redirection to inter-RAT cells is allowed.
Possibility of redirecting the UE to another cell. When the load of the serving cell is within the normal range, a UE may be redir
Possibility of redirecting the UE to another cell. When the UL load state or DL load state of the serving cell is LDR or OLC, a U
BAND4
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
Value range: 0-16383
If the UL UARFCN is not manually set, if RedirBandInd is set to BAND1, BAND2, BAND3, BAND4, BAND5, BAND6, BAND7, B
Orthogonal Variable Spreading Factor (OVSF) of the DL code to be reserved. For details, refer to the 3GPP TS 25.213 protoc
Number of the DL code to be reserved. For details, refer to the 3GPP TS 25.213 protocol.
No. of the DL code to be removed. For details, refer to the 3GPP TS 25.213 protocol.
This parameter specifies the blocked domain type.

This parameter specifies the processing duration of the cell blocking in the RNC.
Uniquely identifying an RNC.

Source ATM address. It should be input in hexadecimal format with prefix of "H'".
1.The first byte of it is recommended to started with H'45 (indicating E.164 address), H'39 (indicating DCC address) or H'47 (in
0x45000971500202001F0000000000000000000000, called E.164A when the last part DSP is not full of zero. H'45 is recomm
2.It should be allocated in the ATM network and cannot be repeated.
Number of the slot
Number of the subsystem
switch of the inner CBS function.

CTCH switch of cell broadcast.
the message code scheme.The enum value is as below:
0000 German
0001 English
0010 Italian
0011 French
0100 Spanish
0101 Dutch
0110 Swedish
0111 Danish
1000 Portuguese
1001 Finnish
1010 Norwegian
1011 Greek
1100 Turkish
1101 Hungarian
1110 Polish
1111 Language unspecified
Repeat Period of send Write-Replace.
Repeat Number of send Write-Replace.
When the switch is on, the Cell dynamic shutdown algorithm of the local RNC cell is enabled. When the switch is off, the Cell d
When the cell is automatically shut down, this parameter is used to repeatedly determine whether the cell needs to be automa
When the cell is automatically enabled, the cell can be automatically disabled again only after a period delay.
This parameter specifies the MTCH multiplexing threshold. When the rate of an MBMS service is lower than this threshold, the
For a PTM service, if the ratio of the intra-frequency cells where the service is transmitted in PTM mode to the intra-frequency
This parameter specifies the X offset for connected mode. For a PTM service in a cell, X UEs that receive this service need to
This parameter specifies the coefficient of the maximum duration of each counting. The maximum duration is MCCH modificat
This parameter specifies the interval between recounting operations.
This parameter specifies the coefficient of the penalty time after the PTP RB admission fails. The penalty time is MCCH modifi
This parameter specifies whether MBMS PTM streaming bearers can pre-empt other MBMS PTM bearers and non-MBMS bea
This parameter specifies whether MBMS PTM streaming bearers can be pre-empted by other MBMS PTM bearers or non-MB
This parameter specifies whether MBMS PTM non-streaming bearers can be pre-empted by other MBMS PTM bearers or non
This parameter specifies the uplink bit rate of the MBMS service in PTP mode. The CN does not assign the uplink rate to the M
Represent an index for a RNC Pool.
RNC Pool name.
Interval for the local RNC sending the heartbeat to the peer RNC in the same RNC pool.
Threshold of continuous failed heartbeat detecting between the two RNCs in a RNC pool.If the heartbeat is not detected from
If the heartbeats are detected from the peer RNC for a successive number of times specified by this parameter, the local RNC
How the RNC state is affected by the Iu interface service state.
If the value is NONE, the RNC state is independent of the Iu interface state(faulty or recovery).
If the value is IUCS, the RNC state is considered to be faulty when Iu CS interface is faulty.
If the value is IUPS, the RNC state is considered to be faulty when Iu PS interface is faulty.
If the value is IUCS_IUPS, the RNC state is considered to be faulty when Iu CS and Iu PS interface are faulty. When Iu CS or
Represent an index for a RNC Pool.
Nrnc ID.
Represent an index for a CN operator. If " peratorType" is set to PRIM, the value range of "Operator Index" is 0-3. If "Operator
If "OperatorType" is set to COMM, the value range of "Operator Index" is 5-31.
Meaning: Roaming capacity rate of the operator. This parameter indicates the roaming capacity rate among operators rather th
In MOCN mode, the RNC obtains the operator in which the roaming UE registers from the IMSI of the UE.
If there are multiple operators that have signed the roaming contract with the local operator in the roaming map,
the RNC routes the UE to an operator according to the roaming capacity rate of operators.
Cause of RRC connection establishment, that is, the value of the establishment cause IE in the RRC CONNECTION REQUES
Channel type and bit rate for RRC connection establishment.

- FACH: The RRC connection is set up on the common channel.
- DCH_3.4K_SIGNALLING: The RRC connection is set up on the 3.4 kbit/s dedicated channel.
Whether the RRC connection is established preferentially on the E-FACH(E-FACH for downlink and RACH for uplink, or E-FAC
regardless of the setting of "SigChType". According to the related protocols, the UE cannot transmit signals over the FACH if b
FACH, even if the "SigChType" is set to FACH. Otherwise, the RRC connection is established on the corresponding channel a
Index of Signaling Radio Bearer (SRB) channel type for an RRC connection establishment. Each index corresponds to a set o
Channel type and data rate for an RRC connection establishment with the cause value of originating conversational call. Value
DCH_6.8K_SIGNALLING indicates that the RRC connection is established on a 6.8 kbit/s dedicated channel. Value DCH_13.
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Originating Streaming Call. Value FA
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Originating Interactive Call. Value FA
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Originating Background Call. Value
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Originating Subscribed traffic Call. V
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating Conversational Call. Va
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating Streaming Call. Value F
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating Interactive Call. Value F
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating Background Call. Value
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Emergency Call. Value DCH_3.4K_S
Value DCH_13.6K_SIGNALLING indicates that the RRC connection is established on a 13.6 kbit/s dedicated channel. Value D
Channel type and data rate for an RRC connection establishment with the cause value of Inter-RAT cell re-selection. Value FA
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Inter-RAT cell change order. Value F
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Registration. Value FACH indicates
indicates that the RRC connection is established on a 6.8 kbit/s dedicated channel. Value DCH_13.6K_SIGNALLING indicates
Channel type and data rate for an RRC connection establishment with the cause value of Detach. Value FACH indicates that t
that the RRC connection is established on a 6.8 kbit/s dedicated channel. Value DCH_13.6K_SIGNALLING indicates that the
Channel type and data rate for an RRC connection establishment with the cause value of Originating High Priority Signalling. V
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Originating Low Priority Signalling. V
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Call re-establishment. Value FACH i
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating High Priority Signalling.
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating Low Priority Signalling.
channel.
Channel type and data rate for an RRC connection establishment with the cause value of Terminating cause unknown. Value
channel.
Channel type and data rate for an RRC connection establishment with the cause value of MBMS ptp RB request. Value DCH_
channel. Value DCH_13.6K_SIGNALLING indicates that the RRC connection is established on a 13.6 kbit/s dedicated channe
Default Channel type and data rate for an RRC connection establishment. Value FACH indicates that the RRC connection is e
is established on a 6.8 kbit/s dedicated channel. Value DCH_13.6K_SIGNALLING indicates that the RRC connection is establ
1)INVOKE_TRACE_SWITCH. When it is checked, RNC will start Invoke Trace procedure upon receiving INVOKE TRACE Me
2)SYS_INFO_UPDATE_FOR_IU_RST. When it is checked, RNC will broadcast SYSTEM INFORMATION messages to UE w
3)DRNC_DIRECT_DSCR. When it is checked, DRNC will start DSCR procedure directly in RRC states other than CELL_DCH
5)RNC_SHARE_SWITCH. When it is checked, RNC traffic share function will be valid, otherwise, RNC traffic function cannot
6)RNCAP_IMSI_HO_SWITCH. When it is checked, Imsi handover function will be used, otherwise it will be not used.
7)TERMINAL_VERSION_DEBASE_SWITCH. When it is checked, terminal version R4 will debase to R99.
8)SYS_HO_OUT_CIPHER_SWITCH. When it is checked, the RNC will add ciphering byte at GSM HANDOVER COMMAND i
9)SYS_HO_CIPHER_CONFIG. When it is checked, the cipher configuration in the added cipher byte in GSM will be A5/1.Whe
10)ARRED_CELL_FOR_CSDOMAIN_RST. When it is checked, cell will be bared when CS domain is invalid, otherwise the C
11)CR2284R1_SWITCH.in section 8.6.6.28 of TS25.331 of R5 Before2006, it describes that the HFN should add one when U
clarify that HFN should add one in RB SETUP process with Timing re-initialized hard handover. when it is checked ,RNC acce
12)CDT_MSG_FULL_TRACE: When it is checked, CDT trace function which starts tracing from message RRC CONNECT RE
13)CR2284R1_COMPATIBLE_SWITCH.CR2284R1 causes the compatible problem. if UE is not consistent with RNC regardin
CR2284R1 according to UE version information. The principles that RNC judges UE whether to accept the CR2284R1 are as
SETUP COMPLETE,RNC figures that UE does not accept the CR; when it is not checked, whether RNC accept the CR or not
(1)CR2284R1_COMPATIBLE_SWITCH is checked, RNC is self-compatible, so the CR2284R1_SWITCH is invalid;
(2)CR2284R1_COMPATIBLE_SWITCH is not checked, the CR2284R1_SWITCH is valid.
14)COMBINE_OPERATION_DRD_SWITCH. When it is on, RNC will not reject the message RB SETUP CMP without the IE a
15)UL_INTER_PROTECT_SWITCH. When the switch is off, RNC will not do integrity protection check for uplink RRC messag
16)FAST_DORMANCY_SWITCH. When it is checked, RNC will apply FAST DORMANCY function.
17)SYS_HO_IN_CIPHER_SWITCH. When it is checked, don't receive the encrypted ability information from RELOC REQ ,de
18)PTT_EARLY_TRANS_SWITCH_OFF. When it is checked, PTT user will not apply the early transmission function, otherwis
19)UPLINK_MDC_ENHENCEMENT_SWITCH. When it is checked, uplink MDC enhancement function will be used.
20)NODEB_PRIVATE_INTERFACE_SWITCH. When it is checked, the NodeB private interface data can be taken to the Node
21)PTT_SPEC_LI_SWITCH_OFF. When it is checked, special LI will not be used for PTT user, otherwise, special LI will be us
22)RNC_DF_2_URA_PCH_SWITCH. When it is checked, RNC will support transferring Fast Dormancy UE from CELL_DCH o
23)FD_TAC_MATCH_SWITCH. When it is checked, RNC will apply FAST DORMANCY function for UE whose TAC is configu
1) LOAD_IRAT_HO_RNC_FILL_TL (TL Input Switch for Load Information About a Cell)
During an inter-RAT handover from a 3G to 2G cell, load information in the Tag Length Value (TLV) format about the 3G cell c
When the switch is turned on, the RNC records the Tag Length in the container.
When the switch is turned off, the RNC does not record the Tag Length.
2) SEND_IDT_JUDGE_IU_RESET (INITIAL UE Message Transmission Switch in the Reset State of the Iu Interface)
When the switch is turned on, the RNC discards the INITIAL UE message from a CN node if the Iu interface of the CN node is
When the switch is turned off, the RNC handles the INITIAL UE message from a CN node if the Iu interface of the CN node is
3) RNC_RBRECFG_DRD_FAIL_ROLLBACK_SWITCH (RB Reconfiguration DRD Rollback Switch)
When the switch is turned on, the RNC supports rollback caused by a failed directed retry of RB reconfiguration.
When the switch is turned off, the RNC does not support rollback caused by a failed directed retry of RB reconfiguration.
4) RNC_CS_QUERY_UE_IMEI_SWITCH (CS IMEI Request Switch)
When the switch is turned on, the RNC rather than the CN sends an IDENTITY REQUEST message to obtain the IMEI of the
When the switch is turned off, the RNC does not send an IDENTITY REQUEST message to obtain the IMEI of the UE.
5) RNC_PS_QUERY_UE_IMEI_SWITCH (PS IMEI Request Switch)
When the switch is turned on, the RNC rather than the CN sends an IDENTITY REQUEST message to obtain the IMEI of the
When the switch is turned off, the RNC does not send an IDENTITY REQUEST message to obtain the IMEI of the UE.
6) RNC_FD_FACH_CONG_CTRL_SWITCH (FACH Congestion Control Switch for UEs Supporting Fast Dormany and Transfe
When the switch is turned on, a UE supporting fast dormancy and transferring to the CELL_FACH state performs congestion c
When the switch is turned off, a UE supporting fast dormancy and transferring to the CELL_FACH state does not perform cong
7) RNC_RBSETUP_DRD_FAIL_ROLLBACK_SWITCH (RB Establishment DRD Rollback Switch)
When the switch is turned on, the RNC supports rollback caused by a failed directed retry of RB establishment.
When the switch is turned off, the RNC does not support rollback caused by a failed directed retry of RB establishment.
8) FP_IUUP_TRACE_SWITCH (Tracing Switch for UEs Failing in FP Synchronization)
When the switch is turned on, a UE failing in FP synchronization can initiate FP/Iu UP data stream tracing.
When the switch is turned off, a UE failing in FP synchronization cannot initiate FP/Iu UP data stream tracing.
ID of an SAS.
Index of a destination signaling point (DSP).
SAS Share Switch.
Indicatin a SAS.
Index of a destination signaling point (DSP).
Identifying the period of the Intra-frequency load balance algorithm. When the cell load is high, the cell PCPICH TX power can
Identifying the potential user control period. When the cell load is high, the cell selection and reselection can be periodically m
Identifying the period of the LDR execution. When basic congestion occurs, execution of LDR can dynamically reduce the cell
the previous result is displayed in LDM. The higher the parameter value is, the more likely this problem can be prevented. If th
The LDR algorithm aims to slowly reduce the cell load and control the load below the admission threshold, each LDR action ta
when the L3 filter coefficient is set to 6), so the parameter value should be higher than 8s.
Identifying the period of the OLC execution. When overload occurs, execution of OLC can dynamically reduce the cell load. W
to the step-function signals is about 2.8s, namely that the system can trace the load control effect about 3 s later after each loa
OlcPeriodTimerLen along with ULOLCFTFRstrctUserNum, DLOLCFTFRstrctUserNum, ULOLCFTFRSTRCTTimes, DLOLCFT
overload. If the OLC period is excessively short, unnecessary adjustment may occur before the previous OLC action has taken
This parameter specifies the interval at which the RNC determines the fairness between the R99 BE service rate and HSUPA
Period of RTWP-based intra-frequency load balancing adjustment. When RTWP is high, CPICH transmit power is periodically
If you set this parameter to TEN_MSEC, use [UL basic meas rprt cycle,Unit:10ms] to specify the measurement report period. I
If you set this parameter to TEN_MSEC, use [DL basic meas rprt cycle,Unit:10ms] to specify the measurement report period. I
Period common measurement protection timer coefficient. Timer length of common measurement report protection = max (100
time exceeds the timer length of common measurement report protection, the common measurement is faulty and a new one
Length of smoothing filter window of intra-frequency load balancing (LDB).
Length of smoothing filter window of potential user control (PUC).
Length of smoothing filter window of uplink LDR.
Length of smoothing filter window of downlink LDR.
Length of smoothing filter window of uplink OLC.
Length of smoothing filter window of downlink OLC.
Length of smoothing filter window of uplink CAC.
Length of smoothing filter window of downlink CAC.
If you set this parameter to TEN_MSEC, use [HSDPA need pwr meas cycle,Unit:10ms] to specify the measurement report per
Length of smoothing filter window of HSDPA power requirement.
Length of smoothing filter window of HSDPA bit rate.
Max allowed number of continuous invalid measurement reports. For detailed information of this parameter, refer to 3GPP TS
If you set this parameter to TEN_MSEC, use [UL OLC meas rprt cycle,Unit:10ms] to specify the measurement report period. If
UL OLC trigger hysteresis.This parameter can avoid touching off OLC event continually.
If you set this parameter to TEN_MSEC, use [DL OLC meas rprt cycle,Unit:10ms] to specify the measurement report period. If
DL OLC trigger hysteresis.This parameter can avoid touching off OLC event continually.
Filter length used for calculating RTWP
Offset of the PCH transmit power from the PCPICH transmit power in a cell. For detailed information of this parameter, refer to
Sequential offset between the SCCPCH and PCCPCH in the cell. As defined by the 25.211 protocol, the PICH timing is 7680 c
the PICH CFN and the corresponding SCCPCH CFN is 2. However, in the 25.435 protocol, the PI information and paging mes
with each other in this aspect. To avoid the compatibility problem, it is recommended that the SCCPCH timing carrying the PC

Sequential offset between the SCCPCH and PCCPCH in the cell. As defined by the 25.211 protocol, the PICH timing is 7680 c
the PICH CFN and the corresponding SCCPCH CFN is 2. However, in the 25.435 protocol, the PI information and paging mes
with each other in this aspect. To avoid the compatibility problem, it is recommended that the SCCPCH timing carrying the PC
Scrambling code of the SCCPCH. 0: primary scrambling code; 1~15: secondary scrambling code. Note: This parameter must
Calculated TFC (CTFC) length of the Transport Format Combination Set (TFCS) on the SCCPCH. This parameter value is rela
This parameter defines the slot format used by the SCCPCH. The configuration of this parameter is relevant to the SF, pilot bi
This parameter indicates whether the SCCPCH involves the TFCI. When the downlink blind transport format detection function
Note: This parameter is configured only for the SCCPCH in the formats 8 to 17.
Indicating whether the CCH carries the MCCH of the MBMS
Uniquely identifying a TFC on the physical channel. The specific parameter value depends on the CTFCSize (2 bits: 0~3, 4 bit
Traffic class. This parameter only applies to interactive and background services, as the Scheduling Priority Indicator (SPI) of
Method of positioning the UE
UE positioning mode when the A-GPS method is selected. The UE supports both UE-based A-GPS mode and UE-assisted A-
This parameter indicates whether the GPS Additional Assistance Data Request is sent when the A-GPS method is used.
Switch for sending A-GPS assistance data in UE-assisted mode. This parameter specifies the GPS data to be sent.
Switch for sending A-GPS assistance data in UE-based mode. This parameter specifies the GPS data to be sent.
Maximum number of satellites whose ephemeris can be delivered when the A-GPS method is used.
UE positioning mode when the OTDOA method is selected. The UE supports both UE-based OTDOA mode and UE-assisted
UE positioning mode when the CELLID+RTT method is selected. The UE supports both UE-based CELLID+RTT mode and U
This parameter specifies whether the RNC specially handles the LCS requests of emergency calls. In other words, the RNC p
This parameter specifies whether the inter-RAT handover, for example, to the GSM network, is performed when the RNC cann
This parameter specifies the type of inter-RAT handover that is performed when the RNC cannot meet the accuracy requireme
This parameter specifies whether the IE is reported to the CN.
When the CELLID+RTT method is selected, this parameter specifies whether forced soft handover is performed if the number
Relative threshold of the event 1A.
Relative threshold of the event 1B.
Delay to trigger the event 1A. The value of this parameter is related to slow fading.
Delay to trigger the event 1B. The value of this parameter is related to slow fading.
Minimum quality threshold of soft handover.
Working mode of positioning for RNC. This parameter is used to determine whether Iupc can be used for positioning. The inte
positioning functions over Iupc. For SAS CENTRIC PREFERRED mode, SAS CENTRIC positioning is selected first. If position
Timer interval for the response from Iupc interface messages. If the timer expires without any response from the SAS, the RNC
receiving the SAS response becomes low.
Shape of the location result sent from the RNC to the CN.
When this parameter is set to AUTOMATIC, the shape of the location result sent from the RNC to the CN depends on the loca
When this parameter is not set to AUTOMATIC, the shape is the configured value. For description of location result shapes, se
ID of an RNC
Cell location configuration type.
Support localization maintenance, Degree mode and Degree Minute and Second mode can be selected.
Support localization maintenance, Metric System and British Measurement can be selected.
Latitude of the cell antenna in the WGS-84 coordinates. The value corresponding to the latitude A degrees B minutes C secon
For example, the value corresponding to the latitude 31 degrees 30 minutes 36 seconds is [31 + (30/60) + (36/3600)] / 0.0000
This is controlled by GCDF and valid when DEG~0(degree format).The value of this parameter has effect on the location resul
Longitude of the cell antenna in the WGS-84 coordinates. The value corresponding to the longitude A degrees B minutes C se
For example, the value corresponding to the longitude 121 degrees 40 minutes 36 seconds is [121 + (40/60) + (36/3600)] / 0.0
Altitude of the cell antenna in the WGS-84 coordinates. This is a necessary parameter, controlled by MTRLGY and valid when
Maximum coverage of the cell antenna.
This is controlled by MTRLGY and valid when MET~0(metric system).
Azimuth of the main lobe of the cell antenna (the clockwise angle from the north to the direction of the main lobe).The value of
Coverage angle of a sector. For an omni-directional cell, the value is 360.The value of this parameter has effect on the location
Average altitude of the cell coverage area in the WGS-84 coordinates. This is controlled by MTRLGY and valid when MET~0(m
Deviation of altitude standard in the cell coverage area in the WGS-84 coordinates.
Environment type of the cell coverage area.
Flag of CELLID+RTT location activation.
Flag of OTDOA location activation.
Flag of A-GPS location activation.

Latitude of the cell center in the WGS-84 coordinates. The value corresponding to the latitude A degrees B minutes C seconds
For example, the value corresponding to the latitude 31 degrees 30 minutes 36 seconds is [31 + (30/60) + (36/3600)] / 0.0000
This is controlled by GCDF and valid when DEG~0(degree format).
Longitude of the cell center in the WGS-84 coordinates. The value corresponding to the longitude A degrees B minutes C seco
For example, the value corresponding to the longitude 121 degrees 40 minutes 36 seconds is [121 + (40/60) + (36/3600)] / 0.0
This is controlled by GCDF and valid when DEG~0(degree format).
Altitude of the cell center in the WGS-84 coordinates. This is controlled by MTRLGY and valid when MET~0(metric system).
Length of the semi-major axis of an uncertain area in the cell center.
Length of the semi-minor axis of an uncertain area in the cell center.
Azimuth of the semi-major axis of an uncertain area in the cell center (the clockwise angle from the north to the semi-major ax
Estimated altitude of an uncertain area in the cell center in the WGS-84 coordinates.
This parameter specifies the latitude of the cell antenna in the WGS-84 coordinates. The input format is ddd:mm:ss.ssss.
This is controlled by GCDF and valid when SEC~1(degree, minute, second format).The value of this parameter has effect on t
Longitude of the cell antenna in the WGS-84 coordinates.The input format is ddd:mm:ss.ssss. This is controlled by GCDF and
This parameter specifies the latitude of the cell center in the WGS-84 coordinates.The input format is ddd:mm:ss.ssss. This is
This parameter specifies the longitude of the cell center in the WGS-84 coordinates.The input format is ddd:mm:ss.ssss.
This is controlled by GCDF and valid when SEC~1(degree, minute, second format).
Altitude of the cell antenna in the WGS-84 coordinates. This is controlled by MTRLGY and valid when IMP~1(British measurem
This parameter specifies the maximum coverage of the cell antenna.
This is controlled by MTRLGY and valid when IMP~1(British measurement).
This parameter specifies the average altitude of the cell coverage area in the WGS-84 coordinates. This is controlled by MTRL
This parameter specifies the standard deviation of altitude in the cell coverage area in the WGS-84 coordinates.
This parameter specifies the altitude of the cell center in the WGS-84 coordinates. This is controlled by MTRLGY and valid wh
This parameter specifies the length of the semi-major axis of an uncertain area in the cell center.
This parameter specifies the length of the semi-minor axis of an uncertain area in the cell center.
This parameter specifies the estimated altitude of an uncertain area in the cell center in the WGS-84 coordinates.
Identifies a group of cells that have specific capabilities for different service types. You can take any value that is not in use. T
Capability of the cells with a specific "Service Priority Group Identity" for R99 real-time services. Value 0 indicates that these c
Capability of the cells with a specific "Service Priority Group Identity" for R99 non-real-time services. Value 0 indicates that the
Capability of the cells with a specific "Service Priority Group Identity" for HSDPA services. Value 0 indicates that these cells do
Capability of the cells with a specific "Service Priority Group Identity" for HSUPA services. Value 0 indicates that these cells do
Capability of the cells with a specific "Service Priority Group Identity" for extension services, such as CMB and MBMS. Value 0
Specifies the weight for service scheduling priority. This weight is used in two algorithms. In scheduling algorithm, it is used to
get more Iub bandwidth, respectively.
Whether to configure SPI weight based on the value range of an HSPA service rate. Value FALSE indicates that the SPI weig
scheduling priority. "SpiWeigth" will not be used for HSPA service when this parameter set to TRUE.
SPI weight corresponding to HSDPA data rate range 1. When the data rate of an HSDPA service is smaller than or equal to "D
SPI weight corresponding to HSDPA data rate range 10. When the data rate of an HSDPA service is greater than "DlRateThre
SPI weight corresponding to HSUPA data rate range 1. When the data rate of an HSUPA service is smaller than or equal to "U
SPI weight corresponding to HSUPA data rate range 10. When the data rate of an HSUPA service is greater than "UlRateThre
When the calculated SQI is greater than the threshold, the voice quality is good.
When the calculated SQI is lower than the threshold, the voice quality is bad. When the calculated SQI is between the value o
Sets the duration that the MS cannot be relocate again after a successful relocation to avoid ping-pong relocation.
When "Transfer Delay Measured by FP Node Between SRNC and DRNC" + "Estimated Non-Measurement Delay Offset" > "T
parameter is set to a smaller value, the unnecessary relocation may occur. If this parameter is set to a greater value, the QoS
"Transfer Delay Provided by the QoS of the Current Traffic" in the formula needs to be sent from the CN to the RNC through a
Sets the interval between the two SRNS relocations based on the Iur resource optimization. For each interval, the RNC specif
cannot be too large. Individually changing a parameter will cause the time difference in the congestion reporting and the reloca
Sets the value of the timer for the relocation triggered after the common channel on the Iur interface is established successfull
Defines the value of the separation timer enabled after the SRNC is separated from the CRNC. The relocation triggers after th
This parameter determines the number of UEs over the Iur interface. If the parameter is set to a greater value, a large number
Sets the relocation-allowed traffic type. If the parameter is set to "RT", only the real-time service can trigger the static relocatio
Uniquely identifying an SSCH in a cell
A timer used to wait for RRC connection setup complete message from UE in RRC procedure.
A timer used to wait for the Iu release command message responding to Iu release request message.
A timer used to retransmit the RRC CONNECTION RELEASE message to UE.
A timer used to wait for the response to paging type 1 in RRC procedure.
A timer used to wait for initial direct transmission.
A timer used to wait for the acknowledgement of radio link control (RLC) completion in RRC procedure.
A timer to RNC wait for the RB setup response from UE in the RB procedure. Refer to the Note.
A timer used to wait UE capability enquiry response.

A timer used to wait for the RB reconfiguration response from UE in the RB procedure. Refer to the Note.
A timer to RNC wait for the RB release response from UE in the RB procedure. Refer to the Note.
A timer to RNC wait for the response to radio link setup request in the radio link procedure.
A timer to RNC wait for the response to radio link reconfiguration prepare in the radio link procedure.
A timer to RNC wait for the response to radio link deletion request in the radio link procedure.
A timer to RNC wait for radio link restoration indication in the radio link procedure.
A timer to DRNC wait for AAL2 setup indication.
A timer to DRNC wait for rnsap radio link reconfiguration commit from SRNC.
A timer to RNC wait for the response to the cell update confirm from UE in forward handover procedure.
A timer to RNC wait for paging response in forward handover procedure.

A timer to RNC wait for relocation request in forward handover procedure.
A timer to RNC wait for the response to active set update in soft handover procedure.
A timer to RNC wait for the response to the TrCh reconfiguration or RB reconfiguration response from UE in hard handover pr
A timer to RNC wait for the response to physical channel reconfiguration in hard handover procedure.
A timer to RNC wait for the relocation command message in relocation procedure.
A timer to RNC wait for the Iu release command message in relocation procedure.
A timer used for data forwarding in relocation procedure.
A timer to RNC wait for another relocation request in relocation procedure.
A timer to RNC wait for rnsap relocation commit message in relocation procedure.
A timer to RNC wait for mobile information confirmation in relocation procedure.
A timer to RNC wait for the response to physical channel reconfiguration in relocation procedure.
A timer to RNC wait for inter-RAT handover completion in relocation procedure.
A timer to DRNC wait for Iu release command in the failed relocation procedure.
A timer to RNC wait for PS RESUME after successful CS InterRAT handover.
A timer to RNC wait for the response to security mode command from UE in security mode procedure.
A timer to RNC wait for the response to counter check in security mode procedure.
A timer to RNC wait for the response to common transport channel resources request in the Iur common transport channel pro
A timer to Iu CS Release protection
A timer to Iu PS Release protection
Wait time in RRC connection reject message, the time period the UE has to wait before repeating the rejected procedure of RR
Index number uniquely identifying the configuration of the typical service
Traffic class. According to the QoS requirements of services, there are four traffic classes: conversational, streaming, interacti
Type of signal source.

- SPEECH: speech service
- UNKNOWN: non-speech service
Maximum bit rate of the service

Whether the service is CS service or PS service
- CS_DOMAIN: Circuit Switched domain service
- PS_DOMAIN: Packet Switched domain service
Power occupancy of the control part of reference TFC. For details, see 3GPP TS 25.214.
Power occupancy of the data part of reference TFC. For details, see 3GPP TS 25.214.
Service handover attribute. If the HO_INTER_RAT_RNC_SERVICE_HO_SWITCH is set to ON, the service handover setting o
- HO_TO_GSM_SHOULD_BE_PERFORM: Handover to the 2G network is performed so long as 2G signals are available.
- HO_TO_GSM_SHOULD_NOT_BE_PERFORM: Handover to the 2G network is performed when 3G signals are weak but 2G
- HO_TO_GSM_SHALL_NOT_BE_PERFORM: Handover to the 2G network is not performed even if 3G signals are weak but
Minimum capability of the 2G cell required for inter-RAT handover from 3G network to 2G network. If the 2G cell is not capable
UL FP mode of this type of RAB. For details about normal mode and silent mode, see section 5.1.1 of 3GPP TS 25.427.
Direction in which the current typical RAB parameters are applied
This parameter specifies whether to allow the service-based handover of UEs from UMTS to LTE.
Direction that the traffic volume measurement is applicable to. DOWNLINK indicates downlink traffic volume measurement. UP
Threshold of triggering event 4A related to DCH traffic volume, that is, the upper limit of the traffic volume. The larger the value
Threshold of triggering event 4B related to DCH traffic volume, that is, the lower limit of the traffic volume. The larger the value
Time from the moment when the traffic volume on the DCH exceeds the upper threshold to the moment when the traffic-relate
above the 4A threshold, and the smaller the possibility of triggering throughput-related event 4A on DCH.
Number of measurement periods during which no event 4A related to DCH traffic volume is reported again after such an even
the next reporting, and the smaller the possibility of triggering such event.
Time from the moment when the traffic volume on the DCH falls below the lower threshold to the moment when the traffic-rela
keeping below the 4B threshold, and the smaller the possibility of triggering throughput-related event 4B on DCH.
Number of measurement periods during which no event 4B related to DCH traffic volume is reported again after such an even
the next reporting, and the smaller the possibility of triggering such event.
Number of measurement periods from the moment when the E-DCH rate falls below the 4A threshold to the moment when the
of the E-DCH throughput keeping below the 4A threshold, and the smaller the possibility of triggering throughput-related event
Number of measurement periods during which no event 4A related to EDCH throughput is reported again after such an event
the next reporting, and the smaller the possibility of triggering throughput-related event 4A on EDCH.
Number of measurement periods from the moment when the E-DCH rate falls below the 4B threshold to the moment when the
of the E-DCH throughput keeping below the 4B threshold, and the smaller the possibility of triggering throughput-related event
Number of measurement periods during which no event 4B related to EDCH throughput is reported again after such an event
the next reporting, and the smaller the possibility of triggering throughput-related event 4B on EDCH.
Number of measurement periods from the moment when the DCH rate falls below the 4B threshold to the moment when the th
DCH throughput keeping below the 4B threshold, and the smaller the possibility of triggering throughput-related event 4B on D
Number of measurement periods during which no event 4B related to DCH throughput is reported again after such an event 4B
next reporting, and the smaller the possibility of triggering throughput-related event 4B on DCH.
Type of transport channel
This parameter specifies the maximum time of a PDU waiting for reordering at the UE. If this timer is too short, data loss occur
This parameter specifies the scope of MAC-hs PDUs waiting for reordering. This parameter is dependent on the transmission
Number of HS-DSCH MAC-d PDU sizes. Currently, only PS conversational services can be configured with multiple HS-DSCH
First MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For streamin
Second MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For strea
Third MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For stream
Fourth MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For stream
Fifth MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For streamin
Sixth MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For streami
Seventh MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For stre
Eighth MAC-d PDU size on the HS-DSCH. For BE services, the size of MAC-d PDUs is usually set to a large value. For stream
This parameter specifies whether to configure the MAC-hs discard timer.
This parameter specifies the maximum time of a MAC-d PDU waiting in the MAC-hs queue after it enters the queue. When thi
The peak rate of a service carried on the E-DCH is equal to this parameter multiplied by the uplink maximum requested rate in
DCH.
Number of E-DCH MAC-d PDU sizes. Currently, only PS conversational services can be configured with multiple E-DCH MAC
First MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Second MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Third MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Fourth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Fifth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Sixth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Seventh MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Eighth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Ninth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Tenth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Eleventh MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Twelfth MAC-d PDU size used by HSUPA services. The size must be a multiple of 8 bits.
Delay time of decision for HSUPA happy bit. If all the buffered user data can be transmitted at the current rate during the time
This parameter specifies the size of the MAC-es reordering RX window. It affects the performance of data packets in terms of
This parameter specifies the maximum time of waiting for an out-of-sequence data packet. A larger value of this parameter lea
Logical serial number of a subflow for the typical RAB. A bearer may use several subflows for transmission. For example, AMR
Therefore, the traffic subflow index is set to 0, which corresponds to one transport channel.
This parameter specifies the type of transport channel for the typical SRB.
Whether to use UL 16QAM.
Whether to use UL enhanced L2.

Whether to use interpolation formula. When the interpolation formula is used, E-TFCI and PO is involved in the calculation of t
speed services. For details, see the 3GPP TS 25.214.
This parameter specifies the initial SIR target value of outer-loop power control algorithm.
This parameter specifies the maximum SIR target value of outer-loop power control algorithm.
This parameter specifies the minimum SIR target value of outer-loop power control algorithm.
This parameter specifies the index of the E-TFCI table used when the service is carried on the E-DCH. For details of this para
This parameter specifies the number of reference E-TFCIs applicable when the service is carried on the E-DCH. For details of
This parameter specifies the index of the PDU size used by reference E-TFCI in the E-TFCI table. For details of this paramete
This parameter specifies the power offset between E-DPDCH and DPCCH associated with the reference E-TFCI in the case o
This parameter and "ERgch3IndStpThs" are used to decide the Serving Grant's upper adjust step. If the current Serving Grant
equal to "ERgch2IndStpThs", the adjust scope is one unit.
This parameter and "ERgch2IndStpThs" are used to decide the Serving Grant's upper adjust step. If the current Serving Grant
equal to "ERgch2IndStpThs", the adjust scope is one unit.
Whether power control parameters in the "MOD UTYPRABHSUPAPC" command are configured for the E-DPCCH Boosting fe
power control parameters in this "MOD UTYPRABHSUPAPC" command are configured for the E-DPCCH Boosting feature. N
configure power control parameters corresponding to one combination of HSUPA features.
Minimum reduced E-DPDCH gain factor used by a UE. For details about this parameter, see 3GPP TS 25.214.
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE when large retransmission is configured. Large retransmission
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE for low-speed data transmission when small retransmission is
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE for high-speed data transmission when small retransmission is
Type of uplink transport channel for the typical RAB
Delay class number. Each delay class number indicates a specified delay time range of Iub transmission.
Target transmission quality of DCH, that is, target BLER of DCH on the radio interface if the subflow is carried on DCH. This Q
the actual BLER, and then round the result up.
Maximum allowed SIR decrease step for HSUPA within an adjustment period of outer-loop power control.
Maximum times of HARQ retransmission of the MAC-es flow that carries this service
Target number of E-DCH PDU retransfer when small probability retransmission is applied to this service. The small probability
Target number of E-DCH PDU retransfer when large probability retransmission is applied to this service. The large probability
Measurement reporting threshold for triggering event 6A1. The event reporting mode is used. Event 6A1 is triggered when the
6A1.
Measurement reporting threshold for triggering event 6A2. The event reporting mode is used. Event 6A2 is triggered when the
Max Ul Tx Power - Relative threshold of 6A2.
Measurement reporting threshold for triggering event 6B1. The event reporting mode is used. Event 6B1 is triggered when the
Relative threshold of 6B1.
Measurement reporting threshold for triggering event 6B2. The event reporting mode is used. Event 6B2 is triggered when the
Max Ul Tx Power - Relative threshold of 6B2.
When a DCH is set up, the UE starts counting the number of faulty CRCs within a specified sliding window. If the number of fa
When a DCH is set up, the UE starts counting the number of faulty CRCs within a specified sliding window. If the number of fa
When event 5A is triggered, a pending timer is started, during which event 5A will not be reported before the specified number
If DL code TX power is higher than the Ea absolute threshold, event Ea is triggered. This event triggers DL QoS operation. Th
If DL code TX power is lower than the Eb absolute threshold, event Eb is triggered. When this event report is received, DL Qo
Type of local transport channel. When this typical traffic is applied on UL, it refers to the UL transport channel type. When this
Peer transport channel type. When this typical traffic is applied on UL, it refers to the DL transport channel type. When this typ
Delay class number. Each delay class number indicates a specified delay time range of Iub transmission.
Work mode of RLC entity.
- AM: Acknowledged Mode. Automatic Repeat Request (ARQ) is used in error correction.
- UM: Unacknowledged Mode. Retransmission is not applied. According to the configuration, the erroneous data is discarded o
- TM: Transparent Mode. No protocol overhead is added to the higher-layer data. The erroneous protocol data units may be di
AM RLC parameter types. The parameters are of three categories, that is, parameters of the transmit end, parameters of rece
This parameter specifies the maximum number of RLC PDUs that the TX end can send when it does not receive acknowledge
The size of the TX window is associated with the RLC throughput. Usually, the larger the window size is, the higher the RLC th
adjusting the window size. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the minimum value of the TX window that can ensure the RLC throughput. This parameter is used on
or equal to that of the [TX window size] parameter.
This parameter specifies the time of waiting for a RESET ACK PDU after sending a RESET PDU to the peer end. This parame
If this timer is set too short, the TX end triggers the retransmission of the RESET PDU too early before receiving the acknowle
For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the maximum number of transmissions of a RESET PDU. This parameter is used only at the TX end
the number of retransmissions reaches the maximum value (Max_RST), the TX end reports an unrecoverable error to upper la
This parameter specifies whether RLC delivers data to the upper layer in sequence or not.
- TRUE: Deliver data in sequence.
- FALSE: Do not deliver data in sequence.
This parameter specifies whether the AM RLC entity discards the Service Data Units (SDUs) that need to be sent and, if so, th
- If this parameter is set to TIMER_BASED_WITH_EXPLICIT_SIGNALLING, [Explicit-ind SDU discard timing] is required for tr
update the RX window. In this mode, [Explicit-ind slide RX window timing], [Explicit-ind SDU discard timing], and [Explicit-ind M
- If this parameter is set to DISCARD_AFTER_MAX_DAT_RETRANSMISSIONS, [Discard PDU max TX] is required for trigger
update the RX window. In this mode, [Discard PDU max TX], [Discard slide RX window timing], and [Discard MRW command
- If this parameter is set to NO_DISCARD, the TX end does not discard any SDU. If the number of transmissions of a PDU exc
This parameter specifies the SDU discard mode of the UM or TM RLC entity. It is applicable only in the RLC UM or TM mode.
- If this parameter is set to TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING, [No-explicit-ind SDU discard] is required for
- If this parameter is not set, the RLC entity buffers an SDU sent from the upper layer until it successfully sends all the content
This parameter specifies the time of waiting for the response after sending an MRW command. This parameter is applicable to
This parameter is applicable to only the AM RLC entity whose [AM RLC discard mode selection] is set to TIMER_BASED_WIT
entity discards the SDU. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the maximum number of retransmissions of an MRW command. This parameter is applicable to only
indicating the discard, to update the RX window. The command will be retransmitted if no response is received after the waitin
This parameter is applicable to only the UM or TM RLC entity whose [UM-TM RLC discard mode selection] is set to TIMER_B
the timer expires, the UM or TM RLC entity discards the SDU. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter is applicable to only the AM RLC entity whose [AM RLC discard mode selection] is set to DISCARD_AFTER_M
command to the RX end, indicating the discard, to update the RX window. For details of this parameter, refer to the 3GPP TS
This parameter is applicable to only the RLC AM entity whose [AM RLC discard mode selection] is set to DISCARD_AFTER_M
SUFI field. After the RLC entity at the TX end discards an SDU, it sends an MRW command to the RX end, indicating the disc
parameter, refer to the 3GPP TS 25.322.
end, indicating the discard, to update the RX window. When the MRW command is sent, a timer is started for waiting for the re
This parameter is applicable to only the AM RLC entity whose [AM RLC discard mode selection] is set to NO_DISCARD. This
reaches the value defined by this parameter. This parameter can be set large, if the target BLER of the transport channel is hi
This parameter specifies the maximum number of RLC PDUs that can be received in a continuous reception procedure. This p
Recommended value (default value): None.
This parameter specifies the minimum value of the RLC RX window that can ensure the RLC throughput. This parameter is us
than or equal to the value of the [RX window size] parameter.
This parameter specifies whether the RX end sends a status report when it detects loss of a PDU. This parameter is used only
- TRUE: The RX end sends a status report when loss of a PDU is detected.
- FALSE: The RX end does not send a status report when loss of a PDU is detected.
This parameter specifies the time during which the RLC entity does not send any status report after the last status report. This
duration of this timer should be longer than the interval between receiving a PDU requested to send and sending a status repo
This parameter specifies the timer after whose expiry the RX end of the AM RLC entity sends a status report. This parameter i
status information to the peer end. Then the timer restarts. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies whether to configure polling parameters for RLC.

This parameter specifies whether to trigger polling when the PDU sent by the TX end of the AM RLC entity is the last one in th
- If this parameter is set to TRUE, polling is triggered when the PDU sent is the last one in the buffer.
- If this parameter is set to FALSE, polling is not triggered when the PDU sent is the last one in the buffer.
- If this parameter is set to TRUE, polling is triggered when the PDU sent is the last one in the retransmission buffer.
- If this parameter is set to FALSE, polling is not triggered when the PDU sent is the last one in the retransmission buffer.
This parameter specifies the minimum interval between two consecutive polling PDU transmissions by the TX end of the AM R
The duration of this timer should be longer than the interval between sending a polling PDU and receiving the requested statu
This parameter specifies the maximum time of waiting for the response from the peer end after the TX end sends a polling PD
expires. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the number of PDUs that the TX end of the AM RLC entity sends before polling the RX end. This par
This parameter specifies the number of SDUs that the TX end of the AM RLC entity sends before polling the RX end. This par
This parameter specifies the PDU TX window percentage at which the TX end of the AM RLC entity polls the RX end. This pa
This parameter specifies the interval between two consecutive polling PDU transmissions by the TX end of the AM RLC entity
This parameter specifies whether to segment UL RLC SDUs. It is applicable to only RLC TM mode.
- TRUE: An SDU from the upper layer will be segmented if its size is greater than that of TMD PDU. In addition, all the PDUs b
- FALSE: More than one RLC SDU can be sent in one TTI by placing one RLC SDU in one TMD PDU. All TMD PDUs in one T
This parameter specifies whether to segment DL RLC SDUs. It is applicable to only RLC TM mode.
- TRUE: An SDU from the upper layer will be segmented if its size is greater than that of TMD PDU. In addition, all the PDUs b
- FALSE: More than one RLC SDU can be sent in one TTI by placing one RLC SDU in one TMD PDU. All TMD PDUs in one T
Delay time between retransmission ratio detection and RLC establishment or reconfiguration
Sampling period of the RLC retransmission ratio monitoring

Filter coefficient of RLC retransmission ratio measurement. The filter coefficient is used to smoothen the original measuremen
based on TCP and not used in RLC flow control algorithm.
Threshold of event A, that is, the upper limit of RLC retransmission ratio. When the monitored RLC retransmission ratio excee
Number of consecutive periods during which the percentage of retransmitted RLC PDUs is higher than the threshold of event
Number of pending periods after event A related to RLC retransmission ratio is triggered. During the pending time, no such ev
Threshold of event B, that is, the lower limit of RLC retransmission ratio. hen the monitored RLC retransmission ratio goes low
Number of consecutive periods during which the percentage of retransmitted RLC PDUs is higher than the threshold of event
Number of pending periods after event B related to RLC retransmission ratio is triggered. During the pending time, no such ev
Delay from the moment when event A is triggered to the moment when the event is reported. Note that this parameter is used
This parameter specifies the number of PDUs that should be transmitted by the AM RLC entity before a poll is started in the D
receiver is polled. Note: This is specific for the DL L2 enhanced scenario.
This parameter specifies the number of SDUs that should be transmitted by the AM RLC entity before a poll is started in the D
receiver is polled. Note: This is specific for the DL L2 enhanced scenario.
This parameter specifies the number of PDUs that should be transmitted by the AM RLC entity before a poll is started in the U
receiver is polled. Note: This is specific for the UL L2 enhanced scenario.
This parameter specifies the number of SDUs that should be transmitted by the AM RLC entity before a poll is started in the U
receiver is polled. Note: This is specific for the UL L2 enhanced scenario.
This parameter specifies the index number that uniquely identifies the configuration of a typical SRB.
This parameter specifies the type of transport channel for the typical SRB.
Whether to use UL 16QAM.
Whether to use UL enhanced L2.

Whether to use interpolation formula. When the interpolation formula is used, E-TFCI and PO is involved in the calculation of t
speed services. For details, see the 3GPP TS 25.214.
This parameter specifies the initial SIR target value of outer-loop power control algorithm.
This parameter specifies the maximum SIR target value of outer-loop power control algorithm.
This parameter specifies the minimum SIR target value of outer-loop power control algorithm.
This parameter specifies the index of the E-TFCI table used when the signaling is carried on the E-DCH. For details of this par
This parameter specifies the number of reference E-TFCIs applicable when the signaling is carried on the E-DCH. For details
Parameters E-RGCH 2-Index-Step Threshold and E-RGCH 3-Index-Step Threshold are used to determine the upper adjustme
equal to the value of E-RGCH 3-Index-Step Threshold and smaller than the value of E-RGCH 2-Index-Step Threshold, the Se
25.321.
Parameters E-RGCH 2-Index-Step Threshold and E-RGCH 3-Index-Step Threshold are used to determine the upper adjustme
equal to the value of E-RGCH 3-Index-Step Threshold and smaller than the value of E-RGCH 2-Index-Step Threshold, the Se
25.321.
The parameter is used to set E-DPCCH Boosting power control parameters.
Minimum reduced E-DPDCH gain factor used by a UE. For details about this parameter, see 3GPP TS 25.214.
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE when large retransmission is configured. Large retransmission
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE for low-speed data transmission when small retransmission is
Hybrid Automatic Repeat reQuest (HARQ) offset used by a UE for high-speed data transmission when small retransmission is
This parameter specifies the index number that uniquely identifies the configuration of a typical SRB.
This parameter specifies the type of transport channel at the local end for the typical SRB.
This parameter specifies the type of transport channel at the peer end for the typical SRB.
This parameter specifies the delay class. According to the specification, a maximum of five delay classes, that is, class 1 to cla
This parameter specifies the index of the dedicated control logical channel of the SRB.
This parameter specifies the work mode of RLC entity.
- AM: Acknowledged Mode. Automatic Repeat Request (ARQ) is used in error correction.
- UM: Unacknowledged Mode. Retransmission is not applied. According to the configuration, the data with errors is discarded
This parameter specifies to edit sender parameters or receiver parameters.

This parameter specifies the maximum number of RLC PDUs that the TX end can send when it does not receive acknowledge
The size of the TX window is associated with the RLC throughput. Usually, the larger the window size is, the higher the RLC th
adjusting the window size.
This parameter specifies the time of waiting for a RESET ACK PDU after sending a RESET PDU to the peer end. This parame
If this timer is set too short, the TX end triggers the retransmission of the RESET PDU too early before receiving the acknowle
This parameter specifies whether the AM RLC entity discards the Service Data Units (SDUs) that need to be sent and, if so, th
- If this parameter is set to TIMER_BASED_WITH_EXPLICIT_SIGNALLING, [Explicit-ind SDU discard timing] is required for tr
update the RX window. In this mode, [Explicit-ind slide RX window timing], [Explicit-ind SDU discard timing], and [Explicit-ind M
- If this parameter is set to DISCARD_AFTER_MAX_DAT_RETRANSMISSIONS, [Discard PDU max TX] is required for trigger
update the RX window. In this mode, [Discard PDU max TX], [Discard slide RX window timing], and [Discard MRW command
- If this parameter is set to NO_DISCARD, the TX end does not discard any SDU. If the number of transmissions of a PDU exc
This parameter specifies the SDU discard mode of the UM RLC entity. It is applicable only in the RLC UM mode. This parame
-If this parameter is set to TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING, "NoExplicitTimerDiscard", is required for trigg
- If this parameter is not set, the RLC entity buffers an SDU sent from the upper layer until it successfully sends all the content
GUI Value Range: NOTUSED, TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING

Unit: None
Actual Value Range: TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING
MML Default Value: None
Recommended Value: None
Parameter Relationship: This parameter is required when the RlcMode parameter is set to UM.
Service Interrupted After Modification : No (No impact on the UE in idle mode)
Impact on Network Performance: None
This parameter specifies the time of waiting for the response after sending an MRW command. This parameter is applicable to
This parameter is applicable to only the AM RLC entity whose [AM RLC discard mode selection] is set to TIMER_BASED_WIT
entity discards the SDU. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the maximum number of retransmissions of an MRW command. This parameter is applicable to only
indicating the discard, to update the RX window. The command will be retransmitted if no response is received after the waitin
This parameter is applicable to only the UM RLC entity whose [UM-TM RLC discard mode selection] is set to TIMER_BASED_
timer expires, the UM RLC entity discards the SDU. For details of this parameter, refer to the 3GPP TS 25.322.
25.322.
This parameter is applicable to only the RLC AM entity whose [AM RLC discard mode selection] is set to DISCARD_AFTER_M
SUFI field. For details of this parameter, refer to the 3GPP TS 25.322.
end, indicating the discard, to update the RX window. When the MRW command is sent, a timer is started for waiting for the re
This parameter is applicable to only the AM RLC entity whose [AM RLC discard mode selection] is set to NO_DISCARD. This
reaches the value defined by this parameter. This parameter can be set large, if the target BLER of the transport channel is hi
This parameter specifies the maximum number of RLC PDUs that can be received in a continuous reception procedure. This p
This parameter specifies whether the RX end sends a status report when it detects loss of a PDU. This parameter is used only
- TRUE: The RX end sends a status report when loss of a PDU is detected.
- FALSE: The RX end does not send a status report when loss of a PDU is detected.
This parameter specifies the time during which the RLC entity does not send any status report after the last status report. This
duration of this timer should be longer than the interval between receiving a PDU requested to send and sending a status repo
This parameter specifies the timer after whose expiry the RX end of the AM RLC entity sends a status report. This parameter i
status information to the peer end. Then the timer restarts. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies whether to configure polling parameters for RLC.

- If this parameter is set to TRUE, polling is triggered when the PDU sent is the last one in the buffer.
- If this parameter is set to FALSE, polling is not triggered when the PDU sent is the last one in the buffer.
- If this parameter is set to TRUE, polling is triggered when the PDU sent is the last one in the retransmission buffer.
- If this parameter is set to FALSE, polling is not triggered when the PDU sent is the last one in the retransmission buffer.
This parameter specifies the minimum interval between two consecutive polling PDU transmissions by the TX end of the AM R
The duration of this timer should be longer than the interval between sending a polling PDU and receiving the requested statu
This parameter specifies the maximum time of waiting for the response from the peer end after the TX end sends a polling PD
expires. For details of this parameter, refer to the 3GPP TS 25.322.
This parameter specifies the number of PDUs that the TX end of the AM RLC entity sends before polling the RX end. This par
This parameter specifies the number of SDUs that the TX end of the AM RLC entity sends before polling the RX end. This par
This parameter specifies the PDU TX window percentage at which the TX end of the AM RLC entity polls the RX end. This pa
This parameter specifies the interval between two consecutive polling PDU transmissions by the TX end of the AM RLC entity
This parameter specifies the number of PDUs that should be transmitted by the AM RLC entity before a poll is started in the L2
receiver is polled. Note: This is specific for the L2 enhanced scenario.
This parameter specifies the number of SDUs that should be transmitted by the AM RLC entity before a poll is started in the L2
receiver is polled. Note: This is specific for the L2 enhanced scenario.
This parameter specifies the type of measurement result that a UE needs to carry in an event-triggered or periodical measurem
to report measurement results of both the types: Reference Signal Received Power (RSRP) and Reference Signal Receiving Q
This parameter specifies the layer 3 filter coefficient for the LTE measurement. Layer 3 filter coefficient is sent to the UE and th
The variables in the formula are defined as follows: a=1/(2^(k/2)), where k is this parameter. Fn-1 is the old filtered measureme
This parameter specifies the duration of the timer that is used in LTE measurement. If the LTE measurement timer reaches the
parameter is set to 0, it indicates that the LTE measurement timer is not started.
This parameter specifies the measurement quantity of a handover target LTE system in an event 3C measurement report sent
Measurement", as is specified in 3GPP TS 25.331.
RSRP is the average power of signals received on all resource elements (REs) that carry reference signals within a certain sym
RSRQ is defined as the ratio of RSRP to RSSI (RSRQ = N*RSRP/RSSI). The coefficient N is introduced to adjust possible ban
This parameter specifies the hysteresis for a UE to report event 3C. For detailed description of the parameter, see 3GPP TS 2
This parameter specifies the interval time between detection of event 3C and sending of the measurement report. How to set t
This parameter specifies the RSRP threshold in the event 3C measurement of LTE during a handover that is not based on cov
25.331.
This parameter specifies the RSRQ threshold in the event 3C measurement of LTE during a handover that is not based on cov
25.331.
The encryption algorithm supported by RNC. Both UEA0 and UEA1 can be selected at one time.
If the times the UE in the CELL_PCH state performs cell reselection is greater than or equal to the threshold, it is regarded tha
message.
This parameter is used to check whether the UE in the low activity state. If the UE is on DCH channel, the low activity counter
When the traffic volume is below the 4B threshold and remains so for the period specified by this parameter, the event 4B is re
Pending time after the traffic volume event 4B for state transition from DCH to FACH is reported. This parameter is used to pre
Pending time after the traffic volume event 4B for state transition from FACH to PCH is reported. This parameter is used to pre
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from FACH t
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to DCH. This p
This parameter is used to check whether the UE in the low activity state. If the UE is on HS-DSCH channel, the low activity co
Pending time after the traffic volume event 4B for state transition from HSPA to FACH is reported. This parameter is used to p
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to HS-DSCH.
This parameter is used to check whether the UE in the low activity state. If the UE is on DCH or HSPA channel, the low activity
Pending time after the traffic volume event 4B for state transition from DCH or HSPA to FACH transition is reported. This para
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of real-time services from F
This parameter specifies the occurrence time of 4A event for triggering the transition of real-time services from FACH to DCH
Period of E-DCH throughput ratio measurement. This parameter specifies the period of E-DCH throughput ratio measurement
This parameter is used to check whether the UE in the low activity state. If the UE is on the E-DCH channel, the low activity co
Number of periods before the throughput ratio event 4B for state transition from E-DCH to FACH is triggered. When the throug
variation. Time to trigger the throughput ratio event 4B = value of this parameter x 10 ms.
Number of pending periods after the throughput event 4B for state transition from E-DCH to FACH is triggered. This paramete
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to E-DCH. Thi
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to HS-DSCH w
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of real-time services from F
This parameter specifies the occurrence time of 4A event for triggering the transition of real-time services from FACH to HSPA
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from FACH to E-DCH with
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of BE services from E_FAC
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to DCH. Th
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to HS-DSC
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of real-time services from E
This parameter specifies the occurrence time of 4A event for triggering the transition of real-time services from E_FACH to DC
This parameter specifies the occurrence time of 4A event for triggering the transition of BE services from E_FACH to CPC. Th
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of real-time services from E
This parameter specifies the occurrence time of 4A event for triggering the transition of real-time services from E_FACH to HS
This parameter specifies the threshold of the traffic volume of 4A event for triggering the transition of fast dormancy user from
Length of the cell reselection frequency timer. This parameter is used together with CellReSelectCounter to detect the frequen
Timer for state transition from DCH to FACH of BE services, used to check whether the UE in the CELL_DCH state with BE se
Timer for state transition from FACH or E_FACH to PCH of BE services, used to check whether the UE in the CELL_FACH sta
Timer for state transition from HS-DSCH to FACH of BE services, used to check whether the UE in the CELL_DCH(with HS-D
Timer for state transition from DCH or HSPA to FACH of real-time services, used to check whether the UE in the CELL_DCH s
Timer for state transition from E-DCH to FACH of BE services, used to check whether the UE in the CELL_DCH(with E-DCH)
Timer for state transition from CPC to FACH of BE services, used to check whether the UE in the CELL_DCH(with CPC) state
Timer for state transition from CPC to FACH of real-time services, used to check whether the UE in the CELL_DCH(with CPC)
Timer for state transition from DCH to E_FACH of BE services, used to check whether the UE in the CELL_DCH(with DCH) st
Timer for state transition from HSPA to E_FACH of BE services, used to check whether the UE in the CELL_DCH(with HSPA)
Timer for state transition from DCH or HSPA to E_FACH of real-time services, used to check whether the UE in the CELL_DC
Timer for state transition from CPC to E_FACH of BE services, used to check whether the UE in the CELL_DCH(with CPC) sta
Timer for state transition from CPC to E_FACH of real-time services, used to check whether the UE in the CELL_DCH(with CP
The integrity protection algorithm supported by RNC. Only UIA1 is supported currently.
This parameter specifies the index of the operator.
This parameter specifies the IP address of the host that does not allow the visit in offload mode.
This parameter specifies the mask of an IP address.
Identity of the UTRAN registration area. The URA is only used by the UTRAN and the CN does not know the URA. The URA c
Traffic class which includes Best Effort(BE) and PTT. BE services comprise interactive services, background services, and IMS
Bearer type of the service. R99 indicates that the service is carried on a non-HSPA channel. HSPA indicates that the service i
Uplink guaranteed bit rate (GBR) of the BE service. GBR is the minimum bit rate that the system can guarantee for the service
Downlink guaranteed bit rate (GBR) of the BE service. GBR is the minimum bit rate that the system shall guarantee for the ser
Traffic class
Defines the happy bit rate of the best effort (BE) service with different user priorities(user priorities can be set by parameter Us
will be decreased. When this parameter is set to zero, it indicates that NodeB will not adjust the HS-DSCH scheduling priority.
This parameter specifies the UL MBR of signal for DRNC HSPA User.
This parameter specifies the DL MBR of signal for DRNC HSPA User.
This parameter specifies the UL MBR of streaming for DRNC HSPA User.
This parameter specifies the DL MBR of streaming for DRNC HSPA User.
This parameter specifies the UL MBR of conversation for DRNC HSPA User.
This parameter specifies the DL MBR of conversation for DRNC HSPA User.
Percentage of User Plane Sharing Out threshold.
Percentage of User Plane Sharing Out Offset.
The parameter is added to trigger the load sharing when the DSP CPU usage exceeds this threshold, thus achieving load bala
The parameter is added to avoid ping-pong handovers during the load sharing triggered by DSP CPU usage.
The parameter is added to stop SPU from assigning users to a DSP whose CPU usage has exceeded this threshold.


Reference used to determine which priority is arranged first in the priority sequence.
If the ARP is preferably used, the priority sequence is gold > silver > copper. If the ARPs are all the same, the TrafficClass is u
If the TrafficClass is preferably used, the priority sequence is conversational > streaming > interactive > background. If the Tra
Decide which carrier is prior when ARP and TrafficClass are both identical.
IMSI of the UE
Set the value "ON", RNC supports VIP users' signalling log report; Set the value "OFF", the function is disabled.
WPS (Wireless Priority Service) is NS/EP (National Security/Emergency Preparedness) AMR conversation service controlled b
This parameter is used to identify WPS users with priority. For instance, if priorities 3, 4, 5, and 6 are selected, users with prior
This parameter specifies the type of a VCL.
Slot number for running this command
local IP address of the IPoA PVC
Peer IP address of IPoA PVC.

Adjacent node identifier
AAL2 PATH ID
This parameter specifies the loopback type.
It specifies the loopback duration.
Subrack number
Slot number
Link type
IMA group number of the low end port
UNI link number corresponding with the low end port
Fractional link number corresponding with the low end port
Optical interface number of the low end port
Subrack number
Slot number
Link type
IMA group number of the high end port
UNI link number of the high end port
Fractional link number of the high end port

Optical interface number of the high end port
VPL/VCL cross type
VPI value of the low end port VPL/VCL
VCI value of the low end port VCL
VPI value of the high end VCL port
VCI value of the high end VCL port
Sending traffic index of the low end VPL/VCL
Receiving traffic index of the low end VPL/VCL
cross connection index

IsKey Mandatory Feature ID Feature Name Value Type
Paging UE in Idle, CELL_PCH,
NO NO WRFD-010301 URA_PCH State (Type 1) Interval Type
WRFD- Dynamic AAL2 Connections in

05030104 Iub/IuCS/Iur Interface
WRFD-050403 Hybrid Iub IP Transmission
WRFD-050404 ATM/IP Dual Stack Node B
WRFD- Dedicated Iub Transmission
YES YES 02130501 Control Interval Type

WRFD- Dedicated Iub Transmission Enumeration
NO YES 02130501 Control Type
NO YES 02130501 Control Interval Type
ATM Transmission Introduction Enumeration
NO YES WRFD-050301 Package Type
ATM Transmission Introduction
NO YES WRFD-050301 Package Interval Type
Dynamic AAL2 Connections in

WRFD- Iub/IuCS/Iur Interface
05030104 Call Admission Based on Used
WRFD- AAL2 Path Bandwidth
05030106 ATM Transmission Introduction
WRFD-050301 Package
WRFD-050301 Package
Iub/IuCS/Iur Interface
Call Admission Based on Used
05030104 CBR, rt-VBR, nrt-VBR, UBR ATM
WRFD- QoS Classes
05030106 Overbooking on ATM
WRFD- Transmission
05030107 ATM QoS Introduction on Hub
WRFD-050405 Node B (Overbooking on Hub
WRFD-050406 Node B Transmission)
Iub/IuCS/Iur Interface
Call Admission Based on Used
05030104 CBR, rt-VBR, nrt-VBR, UBR ATM
WRFD- QoS Classes
05030106 Overbooking on ATM
WRFD- Transmission
05030107 ATM QoS Introduction on Hub
WRFD- Dynamic AAL2 Connections in Enumeration
NO NO 05030104 Iub/IuCS/Iur Interface Type
Overbooking on ATM
Transmission
ATM QoS Introduction on Hub
NO NO WRFD-050406 Node B Transmission) Interval Type
NO NO WRFD-050301 Package Interval Type

NO YES WRFD-050301 Package Any Type


YES NO WRFD-050301 Package Interval Type

NO NO WRFD-050301 Package Type

NO NO 05030104 Iub/IuCS/Iur Interface Interval Type








Hybrid Iub IP Transmission

WRFD-050404 Overbooking on IP Transmission
WRFD-050408 Traffic Priority Mapping onto
WRFD-050424 Transmission Resources
RAN Sharing Phase 2
RAN Sharing Phase 2
YES YES 02130501 Control Type
RAN Sharing Phase 2
WRFD-021305 Dedicated Iub Transmission
WRFD- Control
02130501 Traffic Priority Mapping onto
YES YES WRFD-050424 Transmission Resources Interval Type
RAN Sharing Phase 2
RAN Sharing Phase 2
RAN Sharing Phase 2

Node B (Overbooking on Hub
Node B Transmission)
RAN Sharing Phase 2
NO YES WRFD-050424 Transmission Resources Interval Type
RAN Sharing Phase 2
RAN Sharing Phase 2

NO YES 02130501 Control String Type

Enumeration
NO YES WRFD-020111 One Tunnel Type

NO YES WRFD-010101 3GPP Specifications Interval Type

NO YES 05030104 Iub/IuCS/Iur Interface Interval Type
NO YES None None Interval Type

WRFD-050301 Package
WRFD- Dynamic AAL2 Connections in Enumeration

NO NO 05030104 Iub/IuCS/Iur Interface Type
NO YES MRFD-210304 Faulty Management Interval Type
NO NO MRFD-210304 Faulty Management Interval Type



Enumeration
NO NO MRFD-210304 Faulty Management Type
Enumeration

YES YES MRFD-210304 Faulty Management Interval Type

Enumeration
NO YES MRFD-210304 Faulty Management Type
Enumeration
NO YES None None Type
NO YES MRFD-210301 Configuration Management Interval Type

Enumeration

Enumeration
Enumeration
NO NO MRFD-210304 Faulty Management String Type

Enumeration

Enumeration
Enumeration

Enumeration
NO NO None None Type
YES YES MRFD-210301 Configuration Management Interval Type
YES YES None None Interval Type

Overbooking on ATM
WRFD-050405 Transmission Enumeration
NO YES WRFD-050408 Overbooking on IP Transmission Type
Enumeration
YES NO None None Interval Type

Enumeration
NO NO None None Interval Type

Overbooking on ATM
NO YES WRFD-050405 Transmission Interval Type

WRFD-040100 Flow Control
WRFD- Transmission Recourse Sharing Enumeration
NO NO 02130406 on
RANIub/Iur Interface
Sharing Phase 2 Type
WRFD-021305 Overbooking on ATM
WRFD-050405 Transmission
NO NO WRFD-050408 Overbooking on IP Transmission Interval Type
Overbooking on ATM Enumeration

NO NO WRFD-050405 Transmission Type
Overbooking on ATM
NO NO WRFD-050405 Transmission Interval Type

Overbooking on ATM
NO YES WRFD-050405 Transmission
GSM and UMTS Co-Transmission Interval Type
Resources Management on MBSC
MRFD-211503 Overbooking on ATM
WRFD-010610 HSDPA Introduction Package

YES YES WRFD-010697 E-DPCCH Boosting Interval Type
WRFD-010610 HSDPA Introduction Package Enumeration
NO YES WRFD-010697 E-DPCCH Boosting Type
UBR+ ATM QoS Class

WRFD-050305 CBR, rt-VBR, nrt-VBR, UBR ATM
WRFD- QoS Classes
WRFD-050301 Package
NO NO WRFD-010697 E-DPCCH Boosting Type
UBR+ ATM QoS Class

WRFD- QoS Classes
WRFD-050301 Package
NO NO WRFD-010697 E-DPCCH Boosting Interval Type
UBR+ ATM QoS Class

WRFD- QoS Classes
WRFD-050301 Package
UBR+ ATM QoS Class

WRFD- QoS Classes
WRFD-050301 Package
NO NO WRFD-010697 E-DPCCH Boosting String Type

Enumeration

Enumeration

Enumeration
NO YES MRFD-210301 Configuration Management Type
Enumeration
Enumeration
Enumeration
Enumeration
NO NO MRFD-210301 Configuration Management Type
Enumeration
Enumeration
NO NO MRFD-210301 Configuration Management Interval Type

Enumeration
Enumeration

Enumeration
Enumeration
YES YES MRFD-210305 Security Management Type
NO YES MRFD-210305 Security Management String Type

Enumeration
YES YES MRFD-210305 Security Management Type
NO NO MRFD-210305 Security Management String Type
Enumeration
NO NO MRFD-210305 Security Management Type
NO YES MRFD-210305 Security Management Password Type
Enumeration
Enumeration
YES YES WRFD-050425 Ethernet OAM Interval Type
NO YES WRFD-050425 Ethernet OAM Interval Type
NO YES WRFD-050425 Ethernet OAM String Type

Enumeration
NO NO WRFD-050425 Ethernet OAM Type

NO NO WRFD-050425 Ethernet OAM Interval Type
NO YES WRFD-050425 Ethernet OAM String Type

Enumeration
NO YES WRFD-050425 Ethernet OAM Type

Enumeration
NO YES WRFD-050425 Ethernet OAM Type
Enumeration
NO YES MRFD-210502 BSC/RNC Clock Type

Enumeration
NO NO MRFD-210502 BSC/RNC Clock Interval Type

Enumeration
NO NO MRFD-210502 BSC/RNC Clock Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO YES MRFD-210502 BSC/RNC Clock Interval Type
Enumeration
Enumeration
Enumeration
Enumeration
NO YES MRFD-210305 Security Management Type

WRFD- ATM over Channelized STM- Enumeration
NO YES 05030102 1/OC-3 on Iub Interface Type

NO YES 05030102 1/OC-3 on Iub Interface Type
WRFD- ATM over Channelized STM-
YES NO 05030102 1/OC-3 on Iub Interface Interval Type
YES NO 05030102 1/OC-3 on Iub Interface Interval Type

NO NO 05030102 1/OC-3 on Iub Interface Type
NO NO 05030102 1/OC-3 on Iub Interface Type

NO NO 05030102 1/OC-3 on Iub Interface String Type
NO NO 05030102 1/OC-3 on Iub Interface String Type
Enumeration

MBSC Load Balancing
MRFD-211402 MBSC Service Distribution
MRFD-211403 Load Based 3G-2G Handover Enumeration
NO NO WRFD-070004 Enhancement Based on Iur-g Type
MBSC Service Distribution

MRFD-211403 Load Based 3G-2G Handover
NO NO WRFD-070004 Enhancement Based on Iur-g Interval Type

Enumeration


Enumeration
YES YES None None Type
WRFD- Transmission Recourse Sharing
YES YES 02130406 on Iub/Iur Interface Interval Type
NO YES MRFD-210301 Configuration Management String Type

Enumeration
IP-Based Multi-mode Co-

Transmission on BS side(GBTS)
IP-Based GSM and UMTS Co-
Transmission on MBSC Side
IP Transmission Introduction on
MRFD-211501 Iub Interface
MRFD-211502 IP Transmission Introduction on Iu
WRFD-050402 Interface
WRFD-050409 IP Transmission Introduction on Iur
YES YES WRFD-050410 Interface IP Address Type
NO YES None None IP Address Type
Traffic Priority Mapping onto

YES YES WRFD-050424 Transmission Resources Interval Type

YES NO WRFD-050424 Transmission Resources Interval Type
WRFD- Enumeration
NO YES 05030101 ATM over E1T1 on Iub Interface Type
WRFD- Enumeration
NO NO 05030101 ATM over E1T1 on Iub Interface Type
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
Enumeration
NO NO None None String Type
WRFD- Enumeration
NO YES 05030101 ATM over E1T1 on Iub Interface Type
WRFD-
YES NO 05030101 ATM over E1T1 on Iub Interface Interval Type
Enumeration
Enumeration
NO NO None None Bit Field Type

NO NO None None IP Address Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration

NO YES MRFD-211502 Transmission on MBSC Side IP Address Type

Enumeration
Enumeration
Enumeration
Enumeration
Iub Interface
IP Transmission Introduction on Iu
NO NO WRFD-050410 Interface Interval Type
Enumeration
Iub Interface
Enumeration
NO NO WRFD-050408 Overbooking on IP Transmission Type
Iub Interface
NO YES WRFD-050410 Interface Interval Type
Enumeration
Enumeration
Enumeration

YES YES MRFD-210103 Link aggregation Interval Type

Enumeration
NO NO MRFD-210103 Link aggregation Interval Type
Enumeration
Enumeration
NO YES MRFD-210103 Link aggregation Type

Enumeration
NO NO MRFD-210103 Link aggregation Type
Enumeration
NO YES MRFD-210103 Link aggregation IP Address Type
NO YES MRFD-210103 Link aggregation IP Address Type
NO YES MRFD-210103 Link aggregation Interval Type

Enumeration
NO YES MRFD-210103 Link aggregation Interval Type

Enumeration
Enumeration
YES YES MRFD-210301 Configuration Management Type
Enumeration

Enumeration
NO NO WRFD-040100 Flow Control Interval Type



Enumeration


Enumeration
Enumeration
NO YES WRFD-040100 Flow Control Type
Enumeration
NO NO WRFD-040100 Flow Control Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration

Fractional ATM Function on Iub
YES YES WRFD-050105 ATM Switching Based Hub Node B Interval Type

NO YES WRFD-050105 ATM Switching Based Hub Node B Bit Field Type
Fractional ATM Function on Iub Enumeration
NO YES WRFD-050302 Interface Type
NO YES WRFD-050105 ATM Switching Based Hub Node B Interval Type

Fractional ATM Function on Iub Enumeration
NO NO WRFD-050302 Interface
Fractional ATM Function on Iub Type
Interface
RAN Sharing Introduction Enumeration
RAN Sharing Introduction

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
NO YES MRFD-210502 BSC/RNC Clock String Type
NO YES MRFD-210502 BSC/RNC Clock String Type
YES YES None None IP Address Type
NO YES None None Bit Field Type

IMA for E1T1 or Channelized Enumeration
NO YES WRFD-050304 STM-1/OC-3 on Iub Interface Type
ATM Switching Based Hub Node B
WRFD-050105 IMA for E1T1 or Channelized
YES YES WRFD-050304 STM-1/OC-3 on Iub Interface Interval Type
IMA for E1T1 or Channelized
NO NO WRFD-050304 STM-1/OC-3 on Iub Interface Interval Type

WRFD-050304 STM-1/OC-3 on Iub Interface Enumeration
NO NO WRFD-050105 ATM Switching Based Hub Node B Type

WRFD-050105 IMA for E1T1 or Channelized Enumeration
NO NO WRFD-050304 STM-1/OC-3 on Iub Interface Type
IMA for E1T1 or Channelized Enumeration
NO NO WRFD-050304 STM-1/OC-3
IMA for E1T1 on
or Iub Interface
Channelized Type
STM-1/OC-3 on Iub Interface

NO YES WRFD-050304 STM-1/OC-3 on Iub Interface Interval Type
NO YES WRFD-050304 STM-1/OC-3 on Iub Interface Interval Type
Enumeration
NO NO MRFD-210304 Faulty Management Bit Field Type

Enumeration

Enumeration

Enumeration
Iub Interface
WRFD-050409 IP Transmission Introduction on Iur Enumeration
NO NO WRFD-050410 Interface Type
Iub Interface
Iub Interface
Iub Interface

Enumeration
NO YES None None
Overbooking on ATM Type
WRFD-050405 Transmission Enumeration

YES NO MRFD-211502 Transmission on MBSC Side Interval Type
Enumeration
NO NO WRFD-050107 IP routing Based Hub Node B Interval Type

NO NO 02130406 on
RANIub/Iur Interface
Sharing Phase 2 Type
Dynamic Bandwidth Control of Iub Enumeration
NO YES WRFD-050422 IP Type

GSM and UMTS Co-Transmission
MRFD-211503 Resources Management on MBSC Enumeration


WRFD-050420 FP MUX for IP Transmission Enumeration
NO YES WRFD-050412 UDP MUX for Iu-CS Transmission Type

WRFD-050420 FP MUX for IP Transmission

NO YES WRFD-050412 UDP MUX for Iu-CS Transmission Bit Field Type
NO NO WRFD-050412 UDP MUX for Iu-CS Transmission Interval Type

YES NO WRFD-050412 UDP MUX for Iu-CS Transmission Interval Type
BOOTP
WRFD-031100 Permanent AAL5 Connections for
WRFD- Control Plane Traffic
WRFD-050301 Package
NO YES WRFD-050105 ATM Switching Based Hub Node B IP Address Type
BOOTP
WRFD-050301 Package
NO YES WRFD-050105 ATM Switching Based Hub Node B IP Address Type
Enumeration
NO YES WRFD-050105 ATM Switching Based Hub Node B Type
BOOTP
WRFD-050301 Package
NO NO WRFD-050105 ATM Switching Based Hub Node B Interval Type
BOOTP
WRFD-050301 Package
NO NO WRFD-050105 ATM Switching Based Hub Node B Interval Type
Permanent AAL5 Connections for
WRFD-050301 Package
NO NO WRFD-050107 IP routing Based Hub Node B Interval Type
05030105 ATM Transmission Introduction Enumeration

YES YES WRFD-050402 Iub Interface Interval Type
WRFD-050402 Iub Interface Enumeration
WRFD-050402 Iub Interface
WRFD-050403 Hybrid Iub IP Transmission Enumeration
NO NO WRFD-050404 ATM/IP Dual Stack Node B Type
Iub Interface
ATM/IP Dual Stack Node B
WRFD-050402 Transmission on BS side(GBTS)
WRFD-050403 IP-Based GSM and UMTS Co-
WRFD-050404 Transmission on MBSC Side
MRFD-211501 TDM-Based Multi-mode Co-
MRFD-211502 Transmission via Backplane on BS
NO YES MRFD-211504 side(GBTS) IP Address Type
NO YES WRFD-050404 ATM/IP Dual Stack Node B IP Address Type
NO NO WRFD-050404 ATM/IP Dual Stack Node B IP Address Type
NO YES WRFD-050404 ATM/IP Dual Stack Node B Interval Type
IP Transmission Introduction on Enumeration
NO NO WRFD-050402 Iub Interface Type
NO YES WRFD-050408 Overbooking on IP Transmission Interval Type
NO YES WRFD-050408 Overbooking on IP Transmission Interval Type

WRFD-050404 ATM/IP Dual Stack Node B Enumeration
Iub Interface
NO YES WRFD-050402 Iub Interface IP Address Type
NO NO WRFD-050402 Iub Interface Interval Type
Enumeration


Iub Interface
MRFD-211501 IP Transmission Introduction on Iu

IP routing Based Hub Node B
WRFD-050107 IP Transmission Introduction on Iu
Enumeration
NO YES None None String Type
YES YES MRFD-210103 Link aggregation IP Address Type


Enumeration
NO YES MRFD-210401 BSC/RNC Software Management Type
NO YES MRFD-210401 BSC/RNC Software Management String Type
NO YES MRFD-210401 BSC/RNC Software Management String Type

Enumeration
NO NO MRFD-210403 License Management Type
Enumeration
NO NO MRFD-210403 License Management Type
NO NO MRFD-210403 License Management Interval Type

NO NO MRFD-210403 License Management Bit Field Type


Enumeration
YES YES WRFD-050404 ATM/IP Dual Stack Node B Interval Type
NO NO WRFD-050404 ATM/IP Dual Stack Node B Interval Type






Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

NO NO MRFD-210305 Security Management Interval Type

Enumeration
YES YES WRFD-050409 Interface Interval Type
IP Transmission Introduction on Iu Enumeration

NO YES WRFD-050409 Interface String Type





Enumeration

Enumeration
Enumeration

YES YES MRFD-211501 Transmission on BS side(GBTS) Interval Type
Iub Interface
Iub Interface
Iub Interface
NO YES WRFD-050410 Interface IP Address Type
Iub Interface
Enumeration
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Iub Interface
Iub Interface
Enumeration
Enumeration

Enumeration
NO YES MRFD-211501 Transmission on BS side(GBTS) Interval Type

Iub Interface
YES NO WRFD-050410 Interface Interval Type
Iub Interface

Iub Interface
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

YES YES WRFD-050301 Package Interval Type

NO YES WRFD-050301 Package String Type



WRFD-050301 Package
YES YES WRFD-010101 3GPP Specifications Interval Type





Enumeration
Enumeration

Enumeration

Enumeration
NO NO MRFD-210305 Security Management Bit Field Type

Enumeration
NO YES MRFD-210305 Security Management Compound Type

Enumeration

Enumeration
Enumeration
NO NO MRFD-210305 Security Management Password Type

Enumeration
Enumeration
Enumeration


NO NO WRFD-050301 Package String Type

Enumeration
Enumeration
NO NO 02130501 Control Interval Type
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
NO NO MRFD-210401 BSC/RNC Software Management Type
Enumeration
YES YES MRFD-210401 BSC/RNC Software Management Type
Enumeration
Enumeration
NO NO MRFD-210401 BSC/RNC Software Management Type

YES YES WRFD-050402 Iub Interface Type

YES YES MRFD-211503 Resources Management on MBSC Interval Type
GSM and UMTS Co-Transmission Enumeration

NO YES MRFD-211503 Resources Management
GSM and UMTS on MBSC Type
Co-Transmission
NO NO WRFD-050405 Transmission
NO NO WRFD-050405 GSM and UMTS Co-Transmission Interval Type
Transmission
Transmission
Transmission
Transmission
MRFD-211503 Resources Management on MBSC

Enumeration
Enumeration

YES NO WRFD-050410 Interface Interval Type
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Iub Interface
Enumeration
Enumeration

Enumeration
Iub Interface

Enumeration
Enumeration
Enumeration

Enumeration

Enumeration
NO NO MRFD-210305 Security Management Bit Field Type

Enumeration



MRFD-211503 Traffic Priority Mapping onto
NO NO WRFD-050424 Transmission Resources Interval Type

NO NO MRFD-211503 Resources Management on MBSC Type

NO YES MRFD-211503 Resources Management on MBSC Interval Type
Enumeration
Enumeration
NO NO MRFD-210301 Configuration Management String Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

YES YES WRFD-050406 Node B Transmission) Interval Type
Node B (Overbooking on Hub Enumeration
NO YES WRFD-050406 Node B Transmission) Type
NO YES WRFD-050406 Node B Transmission) Interval Type
RAN Sharing Phase 2
WRFD-021305 Dedicated Iub Transmission
WRFD- Control
02130501 Traffic Priority Mapping onto


Overbooking on ATM
Transmission

WRFD-050301 Package
WRFD- Permanent AAL5 Connections for Enumeration

NO YES 05030105 Control Plane Traffic Type
WRFD- Permanent AAL5 Connections for
NO YES 05030105 Control Plane Traffic Interval Type
WRFD-050301 Package
WRFD-050301 Package
WRFD-050301 Package Enumeration
NO YES WRFD-050404 ATM/IP Dual Stack Node B Type










Enumeration

YES YES WRFD-050404 ATM/IP Dual Stack Node B Interval Type

NO YES WRFD-050402 Iub Interface Type
Iub Interface
WRFD-050404 Transmission on MBSC Side
MRFD-211501 TDM-Based Multi-mode Co-
MRFD-211502 Transmission via Backplane on BS
NO YES MRFD-211504 side(GBTS) IP Address Type
NO YES WRFD-050404 ATM/IP Dual Stack Node B IP Address Type
NO YES WRFD-050402 Iub Interface Type
NO YES WRFD-050402 Iub Interface Interval Type
NO YES WRFD-050402 Iub Interface Interval Type



Enumeration

Enumeration
WRFD-050403 Hybrid Iub IP Transmission Enumeration

Enumeration
NO NO WRFD-050403 Hybrid Iub IP Transmission Type
NO NO WRFD-050403 Hybrid Iub IP Transmission Interval Type



Enumeration
Enumeration
NO YES MRFD-210101 System Redundancy Type
NO NO MRFD-210101 System Redundancy Interval Type


Enumeration
Enumeration
Enumeration
Enumeration

MRFD-210305 Security Management
NO YES MRFD-210403 License Management IP Address Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
NO YES None None Any Type

Enumeration
Enumeration
Enumeration

Enumeration
NO YES None None Any Type
Enumeration
NO NO MRFD-210305 Security Management Compound Type

Enumeration
Enumeration
NO YES None None Compound Type
NO NO None None Compound Type

Enumeration



Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
YES NO None None Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


YES YES WRFD-050406 Node B Transmission) Interval Type





























NO NO WRFD-020134 Push to Talk Interval Type
NO NO WRFD-010701 Uplink Enhanced CELL_FACH Interval Type

WRFD-050406 GSM and UMTS Co-Transmission
YES YES MRFD-211503 Resources Management on MBSC Interval Type
WRFD-050406 GSM and UMTS Co-Transmission Enumeration
NO YES MRFD-211503 Resources Management on MBSC Type
Enumeration
NO NO MRFD-211503 Resources Management on MBSC Interval Type
Overload Control
Overload Control
Overload Control
Overload Control


NO NO 02130501 Control Type

NO NO WRFD-050406 Node B Transmission) Type
















































Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO YES MRFD-210301 Configuration Management Compound Type

Enumeration
Enumeration
Enumeration
Enumeration
NO YES MRFD-210301 Configuration Management Compound Type
Inter-RAT Handover Based on

YES YES WRFD-020303 Coverage Interval Type

Coverage
Inter-RAT Handover Based on DL
WRFD-020303 QoS
WRFD-020309 Inter-RAT Handover Based on
NO NO WRFD-020305 Service Interval Type
NO NO WRFD-010802 Inter RNC Cell Update Interval Type

WRFD-010801 Intra RNC Cell Update
WRFD-021200 HCS (Hierarchical Cell Structure)
WRFD-010801 Intra RNC Cell Update Enumeration
NO NO WRFD-010802 Inter RNC Cell Update Type
WRFD-020103 Inter Frequency Load Balance Enumeration

NO NO WRFD-021200 HCS (Hierarchical Cell Structure) Type
3G/2G Common Load

NO YES WRFD-020310 Management Interval Type
NO NO WRFD-020400 DRD Introduction Package Interval Type

Intra Node B Softer Handover

WRFD-020202 Inter RNC Soft Handover
WRFD-020203 Inter Frequency Hard Handover Enumeration
NO NO WRFD-020302 Based on Coverage Type

NO YES WRFD-020303 Coverage Interval Type
Enumeration
Enumeration
Enumeration
NO NO WRFD-021103 Access Class Restriction Type
NO YES WRFD-021103 Access Class Restriction Interval Type
NO NO WRFD-021103 Access Class Restriction Interval Type

Enumeration
YES YES WRFD-020101 Admission Control Type
NO NO WRFD-020101 Admission Control Interval Type

YES NO WRFD-010101 3GPP Specifications Interval Type

WRFD-020501 Open Loop Power Control
NO NO WRFD-020504 Inner Loop Power Control Interval Type
Enumeration
NO NO WRFD-022000 Physical Channel Management Type
NO YES WRFD-020501 Open Loop Power Control Interval Type
AMR/WB-AMR Speech Rates

NO NO WRFD-020701 Control Interval Type



AMR/WB-AMR Speech Rates Enumeration

NO NO WRFD-020701 Control Type


AMR-WB (Adaptive Multi Rate
Wide Band)
WRFD-010613 AMR/WB-AMR Speech Rates
Wide Band)
Wide Band)
Wide Band)

Wide Band)
WRFD-010613 AMR/WB-AMR Speech Rates Enumeration

Wide Band)

Wide Band)
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
NO NO WRFD-020501 Open Loop Power Control Interval Type
NO NO WRFD-020101 Admission Control Bit Field Type

NO NO WRFD-040100 Flow Control Bit Field Type
Enumeration

Differentiated Service Based on Enumeration

NO NO WRFD-020806 SPI Weight Type
Differentiated Service Based on
NO NO WRFD-020806 SPI Weight Interval Type


WRFD-021304 Package
YES YES WRFD-021311 MOCN Introduction Package Interval Type
NO YES WRFD-011000 Cell Broadcast Service IP Address Type

Enumeration


Enumeration
Enumeration
Enumeration

Enumeration
NO NO None None Any Type
NO NO None None Any Type
YES YES None None String Type

WRFD-050301 Package
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
NO YES WRFD-010101 3GPP Specifications Type
Enumeration
NO NO WRFD-040202 RNC Node Redundancy Type
NO YES WRFD-040202 RNC Node Redundancy Interval Type
NO YES WRFD-021311 MOCN Introduction Package Interval Type

Enumeration
NO NO WRFD-010101 3GPP Specifications Type
NO NO WRFD-010101 3GPP Specifications Interval Type
Enumeration
NO YES WRFD-022000 Physical Channel Management Type
NO NO WRFD-022000 Physical Channel Management Interval Type
NO YES WRFD-022000 Physical Channel Management Interval Type

Enumeration
NO YES WRFD-021200 HCS (Hierarchical Cell Structure) Interval Type
Enumeration

Enumeration
Enumeration
Enumeration
NO YES WRFD-020501 Open Loop Power Control Type
Enumeration
Enumeration
NO YES WRFD-010652 SRB over HSDPA Type
Enumeration
NO YES WRFD-010684 2x2 MIMO Type
Enumeration
NO YES WRFD-010652 SRB over HSDPA Type
Enumeration
NO YES WRFD-010610 HSDPA Introduction Package Type
Inter RNC Soft Handover
Inter Frequency Hard Handover
Based on Coverage
WRFD-020201 Inter Frequency Hard Handover
WRFD-020202 Based on DL QoS
WRFD-020302 Coverage
WRFD-020304 Inter-RAT Handover Based on DL
WRFD-020303 QoS
Video Telephony Fallback to Enumeration

NO NO WRFD-020307 Speech (AMR) for Inter-RAT HO Type
GSM and UMTS Dynamic Enumeration

NO NO MRFD-221802 Spectrum Sharing(UMTS) Type
GSM and UMTS Dynamic

NO NO MRFD-221802 Spectrum Sharing(UMTS) Interval Type
Intelligent Inter-Carrier UE Layered

NO NO WRFD-020135 Management Interval Type
Enumeration

Enumeration
NO NO WRFD-011000 Cell Broadcast Service Type
NO YES WRFD-011000 Cell Broadcast Service Interval Type


Enumeration

NO NO WRFD-020104 Intra Frequency Load Balance Interval Type
NO NO WRFD-010616 MBMS Introduction Package Interval Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO YES WRFD-021103 Access Class Restriction Type
Enumeration
Enumeration
Enumeration
NO YES WRFD-021103 Access Class Restriction Type
Enumeration
Enumeration

Enumeration

WRFD-020101 Admission Control
NO NO WRFD-020102 Load Measurement Bit Field Type
Enumeration
NO YES WRFD-020101 Admission Control Type
Enumeration
WRFD-020106 Load Reshuffling

WRFD-020102 Load Measurement
WRFD-020104 Intra Frequency Load Balance
WRFD-020105 Potential User Control
NO NO WRFD-020107 Overload Control Bit Field Type
WRFD- Enumeration
NO NO 01061006 HSDPA Mobility Management Type
WRFD-010685 Downlink Enhanced L2
WRFD-010688 Downlink Enhanced CELL_FACH
WRFD-010683 Downlink 64 QAM
WRFD-010684 2x2 MIMO
WRFD-010686 CPC - DTX / DRX
WRFD-010687 CPC - HS-SCCH less operation
NO NO WRFD-010702 Enhanced DRX Bit Field Type
WRFD-010611 HSDPA Enhanced Package Enumeration

NO NO WRFD-010652 SRB over HSDPA Type
Enumeration
NO NO WRFD-020103 Inter Frequency Load Balance Type
Enumeration
Enumeration
NO NO WRFD-020101 Admission Control Type




Wide Band)

Wide Band)
Wide Band)

Enumeration


NO NO WRFD-010654 128 HSDPA Users per Cell Interval Type

NO NO WRFD-020102 Load Measurement Interval Type

WRFD-020101 Admission Control Enumeration
NO NO WRFD-020102 Load Measurement Type
NO NO WRFD-010670 128 HSUPA Users per Cell Interval Type
Enumeration
Enumeration
NO YES WRFD-020102 Load Measurement Compound Type

NO YES WRFD-020102 Load Measurement Compound Type
YES YES WRFD-010101 3GPPSharing

RAN Specifications
Introduction Interval Type
WRFD-021304 Package
Enumeration
NO NO WRFD-011001 Simplified Cell Broadcast Type
NO YES WRFD-011001 Simplified Cell Broadcast Any Type
YES YES WRFD-020202 Intra Node B Softer Handover Interval Type

Coverage
Coverage
Coverage

Dynamic Channel Configuration
NO NO WRFD-021101 Control (DCCC) Interval Type
Dynamic Channel Configuration Enumeration
NO NO WRFD-021101 Control (DCCC) Type
Inter-RAT Redirection Based on Enumeration

NO NO WRFD-020401 Distance Type
Inter-RAT Redirection Based on

NO NO WRFD-020401 Distance Interval Type


WRFD-
NO NO 02040002 Inter System Direct Retry Interval Type
Service Steering and Load
WRFD-020120 Sharing in RRC Connection Setup
WRFD- Traffic Steering and Load Sharing Enumeration
NO NO 02040004 During RAB Setup Type
Enumeration
NO NO WRFD-020400 DRD Introduction Package Type
WRFD- Enumeration
NO NO 01061112 HSDPA DRD Type
Enumeration

WRFD-
NO NO 01061112 HSDPA DRD Interval Type
Enumeration
Enumeration

WRFD-020400
WRFD- DRD Introduction Package Enumeration
NO NO 02040003 Inter System Redirect Type
WRFD- Enumeration
NO NO WRFD-020120 Sharing in RRC Connection Setup Interval Type
WRFD- Enumeration
NO NO 02040002 Inter System Direct Retry Type
WRFD-
Intelligent Inter-Carrier UE Layered Enumeration
NO NO WRFD-020135 Management Type

Service Steering and Load Enumeration
NO NO WRFD-020120 Sharing in RRC Connection Setup Type
Domain Specific Access Control

YES YES WRFD-020114 (DSAC) Interval Type
Domain Specific Access Control Enumeration

NO YES WRFD-020114 (DSAC) Type


NO YES WRFD-020114 (DSAC) Bit Field Type

NO YES WRFD-020114 (DSAC) Interval Type


Multi-Carrier Switch off Based on

Traffic Load
WRFD-020117 Multi-Carrier Switch off Based on Enumeration
NO YES WRFD-020122 QoS Type
Traffic Load
WRFD-020117 Multi-Carrier Switch off Based on
NO YES WRFD-020122 QoS Compound Type

Traffic Load

Traffic Load

Traffic Load

Traffic Load

Traffic Load
Traffic Load
NO NO WRFD-020122 QoS Type

NO NO WRFD-020117 Traffic Load Interval Type


Traffic Load
NO NO WRFD-020122 QoS Interval Type
NO NO WRFD-020122 QoS Bit Field Type
Enumeration
NO NO WRFD-010702 Enhanced DRX Type
Enumeration
Enumeration
Enumeration
NO NO WRFD-010688 Downlink Enhanced CELL_FACH Interval Type


UE State in Connected Mode
(CELL-DCH, CELL-PCH, URA- Enumeration
NO NO WRFD-010202 PCH, CELL-FACH) Type
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
Connection and Radio Access
NO NO WRFD-010510 Bearer Establishment and Release Interval Type
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
Enumeration
Enumeration

YES YES WRFD-020803 A-GPS Based LCS Interval Type
Enumeration
NO NO WRFD-020803 A-GPS Based LCS Type

YES NO WRFD-010802 Inter RNC Cell Update Type
NO NO WRFD-021200 HCS (Hierarchical Cell Structure) Interval Type

Enumeration
Enumeration
Enumeration


Based on Coverage
WRFD-020302 Inter-RAT Handover Based on Enumeration
NO NO WRFD-020303 Coverage Type

Based on Coverage
Inter-RAT Handover Based on Enumeration

NO NO WRFD-020305 Service Type

NO NO WRFD-020305 Service Type
WRFD- 15 Codes per Cell

01061001 HSDPA Static Code Allocation and
WRFD- RNC-Controlled Dynamic Code Enumeration
NO NO 01061005 Allocation Type
WRFD- RNC-Controlled Dynamic Code
NO NO 01061005 Allocation Interval Type

WRFD-020108 Code Resource Management
WRFD- Time and HS-PDSCH Codes
NO NO 01061018 Multiplex Interval Type
WRFD-
NO NO 01061004 HSDPA Power Control Interval Type
WRFD-010610
WRFD- HSDPA Introduction Package Enumeration
NO NO 01061004 HSDPA Power Control Type
WRFD- HSDPA H-ARQ & Scheduling Enumeration
NO NO 01061009 (MAX C/I, RR and PF) Type
HSDPA Static Code Allocation and
WRFD- RNC-Controlled Dynamic Code Enumeration
NO NO 01061005 Allocation Type
HSDPA Static Code Allocation and
NO NO WRFD-020108 Code Resource Management Interval Type
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO NO WRFD-010612 HSUPA Introduction Package Interval Type

WRFD-
NO NO 01061203 HSUPA Power Control Interval Type
WRFD-
NO NO 01061203 HSUPA Power Control Interval Type

NO YES WRFD-020117 Traffic Load Interval Type

Inter Frequency Hard Handover Enumeration

Based on Coverage
WRFD-020304 Based on DL QoS Enumeration


NO NO WRFD-020302 Based on Coverage Interval Type




Based on Coverage
NO NO WRFD-020304 Based on DL QoS Type
























Based on Coverage

Based on Coverage
NO NO WRFD-020304 Based on DL QoS Interval Type

Based on Coverage


Based on Coverage
Enumeration

Based on Coverage




Coverage
WRFD-020303 Service
NO NO WRFD-020306 Load Type

NO NO WRFD-020303 Coverage Interval Type

Coverage
WRFD-020303 Inter-RAT Handover Based on DL Enumeration







Coverage
Coverage

Coverage
WRFD-020303 Service
















Coverage
QoS
WRFD-020309 Service
NO NO WRFD-020306 Load Interval Type




Service

Service

Coverage
WRFD-020303 Service
Service

Service

Coverage
WRFD-020303 Service

Service
Service

Service

Coverage
QoS
WRFD-020309 Service
Service
Load
MRFD-211404 MBSC Handover based on Load
WRFD-020305 Enhancement
WRFD-020306 Load Based 3G-2G Handover
Service
Load
Service

Service

Service

Service
WRFD-020202 Intra Node B Softer Handover Enumeration

NO NO WRFD-020203 Inter RNC Soft Handover Type






WRFD-020202 Intra Node B Softer Handover

NO NO WRFD-020203 Inter RNC Soft Handover Interval Type
















NO NO WRFD-020106 Load Reshuffling Interval Type

NO NO WRFD-020107 Overload Control Interval Type

Enumeration
NO NO WRFD-020106 Load Reshuffling Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

WRFD-020106 Load Reshuffling Enumeration

NO NO WRFD-020108 Code Resource Management Type
Enumeration
Enumeration
Enumeration

NO NO WRFD-020103 Inter Frequency Load Balance Type
Enumeration
NO NO WRFD-020106 Load Reshuffling Bit Field Type
Enumeration
NO NO WRFD-020160 Enhanced Multiband Management Type


Based on Coverage
Enumeration
Enumeration


Enumeration


Coverage
WRFD-020303 Service
Enumeration

Coverage
Coverage
WRFD-020303 Service
Coverage

Coverage

Service

Service

Enumeration
Enumeration
NO YES WRFD-010616 MBMS Introduction Package Type
Enumeration
WRFD-
NO NO 01061603 MBMS Load Control Interval Type
WRFD-
Enumeration
NO NO WRFD-010660 MBMS Phase 2 Type
WRFD-
NO NO 01066001 MBMS Enhanced Broadcast Mode Interval Type
WRFD-
YES YES None NoneSharing Introduction

RAN Interval Type
WRFD-021304 Package
YES YES WRFD-010616 MBMS Introduction Package Interval Type
Enumeration
Enumeration
Enumeration


Enumeration
NO NO WRFD-010616 MBMS Introduction Package Type
NO YES WRFD-010616 MBMS Introduction Package Interval Type

MBMS FLC(Frequency Layer
Convergence)/FLD(Frequency Enumeration
NO NO WRFD-010626 Layer Dispersion) Type
WRFD- Enumeration
WRFD-
WRFD- Enumeration
WRFD-
WRFD-
WRFD-


Enumeration
Enumeration
Enumeration
Mobility Between UMTS and LTE

NO YES WRFD-020126 Phase1 Interval Type

NO NO WRFD-020126 Phase1 Interval Type

Mobility Between UMTS and LTE Enumeration

NO NO WRFD-020126 Phase1 Type



















Enumeration
NO NO WRFD-020107 Overload Control Type
NO NO WRFD-020105 Potential User Control Interval Type


Based on DL QoS

Based on DL QoS

Based on DL QoS
Inter-RAT Handover Based on DL Enumeration














Control (DCCC)
Control
Control

Control
Control
NO YES WRFD-020309 QoS Interval Type




NO YES WRFD-020304 Based on DL QoS Interval Type
Control (DCCC)
Control (DCCC)

Control (DCCC)
Control (DCCC)
Control (DCCC)
Control (DCCC)

Control (DCCC)

YES YES WRFD-020120 Sharing in RRC Connection Setup Type





Enumeration
YES YES WRFD-020101 Admission Control Type
NO YES WRFD-020101 Admission Control Interval Type


Enumeration
NO YES WRFD-020108 Code Resource Management Type



WRFD-010802 Inter RNC Cell Update
WRFD-010901 Intra RNC URA Update
NO NO WRFD-010902 Inter RNC URA Update Interval Type


Enumeration
NO NO WRFD-010801 Intra RNC Cell Update Type
NO YES WRFD-010801 Intra RNC Cell Update Interval Type



NO NO WRFD-010801 Intra RNC Cell Update Interval Type


Enumeration
Enumeration
Enumeration
Intra RNC Cell Update

WRFD-010801 Mobility Between UMTS and LTE
Intra RNC Cell Update

System Information Broadcasting
NO NO WRFD-020126 Phase1 Bit Field Type

Phase1
WRFD-020126 PS Service Redirection from Enumeration
NO NO WRFD-020129 UMTS to LTE Type
Phase1

Phase1
WRFD-020126 PS Service Redirection from
NO NO WRFD-020129 UMTS to LTE Interval Type
Phase1
Phase1

Phase1
Phase1
Phase1


NO NO WRFD-010101 3GPP Specifications Bit Field Type
Enumeration

Enumeration
Enumeration

Coverage
Coverage

Coverage
Based on Coverage
Coverage
NO YES WRFD-020302 Based on Coverage Type
WRFD- Inter Frequency Hard Handover
01061006 Based on Coverage
WRFD- HSDPA Mobility Management Enumeration
NO NO 01061204 HSUPA Mobility Management Type

WRFD- Inter Frequency Hard Handover
01061006 Based on Coverage
WRFD- HSDPA Mobility Management Enumeration
NO NO 01061204 HSUPA Mobility Management Type
Coverage
3GPP Specifications
WRFD-010101 Control (DCCC)
MRFD-211502 Transmission on MBSC Side
WRFD-021311 MOCN Introduction Package Enumeration
YES YES WRFD-040202 RNC Node Redundancy Type
Connection with TMA (Tower

Mounted Amplifier)
3GPP Specifications
MRFD-210601 Conversational QoS Class
WRFD-010101 Interactive QoS Class
WRFD-010501 Integrity Protection
WRFD-010503 Encryption
WRFD-011401 ATM over E1T1 on Iub Interface
WRFD-011402 ATM over Channelized STM-
WRFD- 1/OC-3 on Iub Interface
05030101 NACC Procedure Optimization
WRFD- MBSC Load Balancing
05030102 MBSC Service Distribution
MRFD-211402 Enhancement
MRFD-211403 IP-Based GSM and UMTS Co-
Enumeration
NO NO WRFD-010401 System Information Broadcasting Interval Type

WRFD-021304 Package
3GPP Specifications
NO YES WRFD-040202 RNC Node Redundancy Type
Enumeration
Enumeration
Iu Flex Load Distribution
Management
WRFD-021306 MOCN Introduction Package
WRFD-021311 IP-Based GSM and UMTS Co- Enumeration
NO YES MRFD-211502 Transmission on MBSC Side Type
WRFD-021306 Management
Package
WRFD-050301 IP Transmission Introduction on Iu Enumeration
Interface
WRFD-050409 IP-Based GSM and UMTS Co- Enumeration
NO NO MRFD-211502 Transmission on MBSC Side Type
Enumeration

Quality Improvement for
Subscribed Service
WRFD-020128 Web Browsing Acceleration
WRFD-020132 P2P Rate Restriction During Busy Enumeration
NO NO WRFD-020133 Hours Type

WRFD-021304 Package

YES YES WRFD-020114 (DSAC) Type
Enumeration
NO YES WRFD-010101 3GPP Specifications
RAN Sharing Introduction Type
WRFD-021304 Package
NO YES WRFD-021311 MOCN Introduction Package String Type
NO YES None None

RAN Sharing Introduction String Type
WRFD-021304 Package
NO NO WRFD-021311 MOCN
RAN Introduction
Sharing Package
WRFD-021304 Package

WRFD-020804 LCS Classified Zones
WRFD- Dedicated Carrier for Each
02130401 Operator
YES YES WRFD-040202 RNC Node Redundancy Interval Type

NO YES 02130401 Operator String Type
MOCN Introduction Package
WRFD-021311 Dedicated Carrier for Each
WRFD- Operator
02130401 RAN Sharing Introduction Enumeration
WRFD- Operator
02130401 RAN Sharing Introduction
WRFD- Operator
WRFD- Operator
WRFD- Operator
NO NO WRFD-021311 MOCN Introduction Package Interval Type

Enumeration
NO NO WRFD-011402 Encryption Type
NO YES WRFD-011402 Encryption Interval Type
WRFD-
01061008 Interactive and Background Traffic
WRFD- Class on HSDPA
01061112 HSDPA DRD
WRFD- Interactive and Background Traffic
01061206 Class on HSUPA
WRFD- HSUPA 2ms TTI
01061403 Streaming Traffic Class on HSDPA
WRFD-010630 Streaming Traffic Class on HSUPA
WRFD-010632 SRB over HSUPA
WRFD-010636 SRB over HSDPA
WRFD-010687 Dynamic Channel Configuration
WRFD-
01061403 HSUPA 2ms TTI
WRFD- HSUPA 2ms/10ms TTI Handover
01061404 SRB over HSUPA
WRFD-010636 SRB over HSDPA

Adaptive Configuration of Traffic
NO NO WRFD-010712 Channel Power offset for HSUPA Interval Type
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
WRFD-010615 Multiple RAB Package (PS RAB

WRFD- ≥2)
01061501 Combination of Two PS Services
WRFD- Combination of One CS Service
01061502 and Two PS Services
WRFD- Combination of Three PS Services
01061503 Combination of One CS Service
WRFD- and Three PS Services
01061504 Downlink 64 QAM
WRFD-010687 PDCP Header Compression
WRFD-011500 (RFC2507)
WRFD-011501 PDCP Header Compression
WRFD- (RoHC)
02060504 Lossless SRNS Relocation
NO NO WRFD-010697 E-DPCCH Boosting Bit Field Type
WRFD-
01061111 HSDPA State Transition
WRFD- HSUPA DCCC
01061208 HSUPA 2ms/10ms TTI Handover
WRFD- Active Queue Management (AQM)
01061404 Dynamic Channel Configuration
NO NO WRFD-050408 Overbooking on IP Transmission Bit Field Type
TFO/TrFO
NO NO WRFD-020701 Control Bit Field Type
Outer Loop Power Control

WRFD-020503 Inner Loop Power Control
WRFD-020504 Downlink Power Balance
WRFD-020502 HSUPA Power Control
WRFD- Adaptive Configuration of Traffic
01061203 Channel Power offset for HSUPA
WRFD-010712 HSUPA Coverage Enhancement
NO NO WRFD-020138 at UE power limitation Bit Field Type
WRFD-
01061006
WRFD- HSDPA Mobility Management
01061204 HSUPA Mobility Management
NO NO WRFD-021200 HCS (Hierarchical Cell Structure) Bit Field Type
WRFD-
WRFD-010630 Streaming Traffic Class on HSDPA
WRFD-010632 Streaming Traffic Class on HSUPA
NO NO WRFD-010688 Downlink Enhanced CELL_FACH Bit Field Type
Control (DCCC)
WRFD-021101 RAB Quality of Service
NO NO WRFD-010506 Renegotiation over Iu Interface Bit Field Type
WRFD-020120
WRFD- HSDPA DRD
02040001 Service Steering and Load
WRFD- Sharing in RRC Connection Setup
02040002 Intra System Direct Retry
WRFD- Inter System Direct Retry
02040003 Inter System Redirect
WRFD- Traffic Steering and Load Sharing
NO NO 02040004 During RAB Setup Bit Field Type
HSDPA Mobility Management

HSUPA Mobility Management
Inter Frequency Load Balance
WRFD- Intra Frequency Hard Handover
01061006 Inter Frequency Hard Handover
WRFD- Based on Coverage
01061204 Inter-RAT Handover Based on
WRFD-020301 Service
WRFD-020303 Load
WRFD-020304 Video Telephony Fallback to
WRFD-020305 Speech (AMR) for Inter-RAT HO
WRFD-020306 Inter-RAT Handover Phase 2
WRFD-020307 NACC(Network Assisted Cell
WRFD-020308 Change)
WRFD- PS Handover Between UMTS and
02030801 GPRS
WRFD- Inter-RAT Handover Based on DL
02030802 QoS
NO NO WRFD-020129 UMTS to LTE Bit Field Type
WRFD-020605 SRNS Relocation Introduction
WRFD- Package
02060501 SRNS Relocation (UE Not
WRFD- Involved)
02060502 SRNS Relocation with Hard
WRFD- Handover
02060503 SRNS Relocation with Cell/URA
WRFD- Update
NO NO 02060504 Lossless SRNS Relocation Bit Field Type
HSDPA Mobility Management

HSUPA Mobility Management
Based on Coverage
WRFD- Coverage
01061006 Inter Frequency Hard Handover
WRFD- Based on DL QoS
01061204 Inter-RAT Handover Based on
WRFD-020302 Service
WRFD-020304 Load
WRFD-020305 Inter-RAT Handover Phase 2
WRFD-020306 PS Handover Between UMTS and
WRFD-020308 GPRS
WRFD- Inter-RAT Handover Based on DL
02030802 QoS
WRFD-020309 3G/2G Common Load
NO NO WRFD-020310 Management Bit Field Type



YES YES WRFD-021000 Transport Channel Management Interval Type

NO NO WRFD-040100 Flow Control Bit Field Type





NO NO WRFD-020120 Sharing in RRC
RAN Sharing Connection Setup Interval Type
Introduction
WRFD-021304 Package
YES YES WRFD-020804 LCS Classified Zones Interval Type

WRFD- Enumeration
NO NO 01061208 HSUPA DCCC Type
NO YES WRFD-021101 Control (DCCC) Type
WRFD- Enumeration

YES YES WRFD-020135 Management Interval Type
NO YES WRFD-020135 Management Type
NO YES WRFD-020135 Management String Type
NO NO WRFD-020135 Management String Type

YES YES WRFD-020135 Management Interval Type



Inter-RAT Redirection Based on Enumeration

NO NO WRFD-020401 Distance Type





Enumeration

Enumeration
Enumeration
NO NO None None
Overbooking on IP Transmission Type
WRFD-050408 Overbooking on ATM Enumeration
NO NO WRFD-050405 Transmission Type

Enumeration
NO NO WRFD-020123 TCP Accelerator Bit Field Type

Enumeration
Enumeration
Enumeration

Subscribed Service
WRFD-020132 P2P Rate Restriction During Busy
NO NO WRFD-020133 Hours Interval Type
Subscribed Service
Subscribed Service

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Subscribed Service


WRFD-
WRFD-020120 Sharing in RRC Connection Setup
Enumeration
WRFD- Enumeration
NO NO 01061112 HSDPA DRD Type
Enumeration
WRFD-020120 Service Steering and Load

WRFD- Sharing in RRC Connection Setup Enumeration

WRFD-

WRFD-

Enumeration

Enumeration
WRFD-020400
WRFD- DRD Introduction Package Enumeration
WRFD- Enumeration
WRFD-
NO NO 02040003 Inter System Redirect Interval Type
WRFD-
NO NO 02040003 Inter System Redirect Interval Type
WRFD- Enumeration
WRFD-
WRFD-
WRFD-
02040002 Inter System Direct Retry
WRFD-020402 Measurement Based Direct Retry

NO YES WRFD-020120 Sharing in RRC Connection Setup Interval Type
NO YES WRFD-020120 Sharing in RRC Connection Setup Interval Type
NO NO WRFD-020114 (DSAC) Type




Enumeration
YES YES WRFD-010686 CPC - DTX / DRX Type
Enumeration
YES YES WRFD-010612 HSUPA Introduction Package Type
Enumeration
NO NO WRFD-010686 CPC - DTX / DRX Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
Subscribed Service
WRFD- HSUPA DCCC
NO NO WRFD-021101 Control (DCCC) Bit Field Type
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration

NO YES WRFD-020303 Coverage String Type
3G/2G Common Load Enumeration
NO YES WRFD-020310 Management Type
NACC Procedure Optimization
MBSC Load Balancing
MBSC Handover based on Load
MRFD-211404 Shared Network Support in
MRFD-211502 Connected Mode
WRFD- Operator
02130401 MOCN Introduction Package
NO YES WRFD-070004 Enhancement Based on Iur-g String Type

MBSC Load Balancing
MRFD-211404 Shared Network Support in
MRFD-211502 Connected Mode
WRFD- Operator
NO YES WRFD-070004
WRFD-020203 Enhancement Based on Iur-g String Type
WRFD- Inter RNC Soft Handover
NO YES 02131103 MOCN Mobility Management Interval Type
3GPP Specifications
WRFD-010101 Shared Network Support in
NO YES WRFD-021301 Connected Mode Interval Type
SRNS Relocation Introduction Enumeration

Coverage
QoS
WRFD-020309 Service
NO YES WRFD-020306 Load Type
WRFD- NACC(Network Assisted Cell Enumeration
NO NO 02030801 Change) Type
WRFD- PS Handover Between UMTS and Enumeration
NO NO 02030802 GPRS Type

Coverage
WRFD-020303 QoS

Enumeration
NO YES None
WRFD-020203 None String Type
WRFD- Inter RNC Soft Handover
NO YES 02131103 MOCN Mobility Management Interval Type
Enumeration
NO YES WRFD-010102 Operating Multi-band Type
Enumeration


Enumeration
3GPP Specifications
WRFD-010101 Shared Network Support in
NO YES WRFD-021301 Connected Mode Interval Type

Enumeration
NO YES WRFD-010802 Inter RNC Cell Update Interval Type
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO YES WRFD-020501 Open Loop Power Control Type
Enumeration
Enumeration
Enumeration
NO NO WRFD-010684 2x2 MIMO Type
Enumeration
Enumeration
NO NO WRFD-010610 HSDPA Introduction Package Type
WRFD-020203 Direct Signaling Connection Re-
NO YES WRFD-021400 establishment (DSCR) Bit Field Type
Enumeration
Enumeration

WRFD-020203 Based on Coverage
Enumeration
NO YES WRFD-010688 Downlink Enhanced CELL_FACH Type
Enumeration

NO NO WRFD-021000 Transport Channel Management Interval Type
Enumeration
NO NO WRFD-020900 Logical Channel Management Type
Enumeration
Enumeration
Enumeration
NO NO WRFD-021000 Transport Channel Management Type
Enumeration
Enumeration
YES YES WRFD-010688 Downlink Enhanced CELL_FACH Type
Enumeration
YES YES WRFD-010688 Downlink Enhanced CELL_FACH Type

Enumeration
YES YES WRFD-021000 Transport Channel Management Type

NO NO WRFD-010652 SRB over HSDPA Interval Type

Enumeration
NO NO WRFD-020504 Inner Loop Power Control Type

Enumeration
Enumeration
Enumeration

Paging UE in Idle, CELL_PCH,
URA_PCH State (Type 1)
WRFD-010301 Paging UE in CELL_FACH,
NO NO WRFD-010302 CELL_DCH State (Type 2) Interval Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
NO NO WRFD-010632 Streaming Traffic Class on HSUPA Type
Enumeration
NO NO WRFD-010612 HSUPA Introduction Package Type
Enumeration
Enumeration
Enumeration
WRFD- Enumeration
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
Connection and Radio Access Enumeration
NO NO WRFD-010510 Bearer Establishment and Release Type
3.4/6.8/13.6/27.2Kbps RRC
NO YES WRFD-010510 Bearer Establishment and Release Type
Enumeration
NO NO WRFD-010617
WRFD-010632 VoIP over HSPA/HSPA+ Type
WRFD- Streaming Traffic Class on HSUPA Enumeration
NO NO 01061403
WRFD- HSUPA 2ms TTI Type
01061206 Interactive and Background Traffic
WRFD- Class on HSUPA Enumeration
NO NO 01061403 HSUPA 2ms TTI Type
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
NO NO WRFD-010685 Downlink Enhanced L2 Interval Type
NO NO WRFD-010695 UL Layer 2 Improvement Interval Type
NO NO WRFD-010695 UL Layer 2 Improvement Interval Type
HSPA+ Downlink 28Mbps per

User
WRFD-010680 HSPA+ Downlink 21Mbps per
WRFD-010681 User
WRFD-010683 Downlink 64 QAM Enumeration
NO NO WRFD-010684 2x2 MIMO Type
Enumeration
WRFD-010652
WRFD- SRB over HSDPA
WRFD-010636 SRB over HSUPA
NO NO WRFD-010697 E-DPCCH Boosting Bit Field Type
Enumeration
NO NO WRFD-010619 CS voice over HSPA/HSPA+ Type
NO NO WRFD-010619 CS voice over HSPA/HSPA+ Interval Type
NO NO WRFD-010619 CS voice over HSPA/HSPA+ Interval Type

Enumeration
NO NO WRFD-010618 IMS Signaling over HSPA Type
Enumeration
NO NO WRFD-010636 SRB over HSUPA Type
HSPA+ Downlink 28Mbps per
User
WRFD-010680 HSPA+ Downlink 21Mbps per Enumeration
NO NO WRFD-010681 User Type

Enumeration
Enumeration
Enumeration

Enumeration

Enumeration

Enumeration
NO NO WRFD-010619 CS voice over HSPA/HSPA+ Type
Enumeration
NO NO WRFD-010617 VoIP over HSPA/HSPA+ Type
Enumeration
Enumeration
NO NO WRFD-010618 IMS Signaling over HSPA Type
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
NO NO WRFD-010630 Streaming Traffic Class on HSDPA Type

WRFD- Interactive and Background Traffic Enumeration
NO NO 01061008 Class on HSDPA Type
WRFD-010612 HSUPA Introduction Package Enumeration
WRFD-010612 HSUPA Introduction Package
WRFD- Interactive and Background Traffic Enumeration
NO NO 01061206 Class on HSUPA Type

Enumeration

Enumeration
Enumeration
Enumeration


NO NO WRFD-020203
01061006 Inter RNC Soft Handover Type
NO NO 01061204 HSUPA Mobility Management Interval Type

Based on Coverage
WRFD-
NO NO 01061204
01061006 HSUPA Mobility Management Interval Type
NO NO 01061204 HSUPA Mobility Management Interval Type
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
YES YES WRFD-010687 CPC - HS-SCCH less operation Type
Enumeration
YES YES WRFD-010687 CPC - HS-SCCH less operation Type
Enumeration
Enumeration
NO NO WRFD-010687 CPC - HS-SCCH less operation Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration

WRFD-021304 Package
Enumeration
Enumeration
YES YES WRFD-010616 MBMS Introduction Package Type

Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
YES YES WRFD-020500 Enhanced Fast Dormancy Type
YES YES WRFD-020500 Enhanced Fast Dormancy Interval Type
NO YES WRFD-020500 Enhanced Fast Dormancy String Type

Enumeration
NO NO WRFD-020500 Enhanced Fast Dormancy Type

WRFD-021304 Package

WRFD-021304 Package
WRFD-021304 Package
YES YES WRFD-021303 IMSI Based Handover String Type
YES YES WRFD-021303 IMSI Based Handover String Type

Shared Network Support in
WRFD-021301 Connected Mode Enumeration
YES YES WRFD-021303 IMSI Based Handover Type
YES YES WRFD-021301 Connected Mode Interval Type

Connected Mode
MBSC Load Balancing
WRFD-021301 MBSC Service Distribution
MRFD-211502 Dedicated Carrier for Each
WRFD- Operator
YES YES WRFD-070004 Enhancement Based on Iur-g String Type

Connected Mode
MBSC Load Balancing
WRFD- Operator
Based on Coverage





Based on Coverage

























Based on Coverage
Based on Coverage
Based on Coverage

Based on Coverage
Enumeration

Based on Coverage












WRFD-020103 Inter Frequency Load Balance



NO YES WRFD-020302 Based on Coverage Interval Type
WRFD-
NO NO 02040001 Intra System Direct Retry Interval Type
Enumeration

Enumeration
Enumeration



Coverage
WRFD-020303 Service


Coverage






Coverage

Coverage
Coverage
WRFD-020303 Service
















Coverage
QoS
WRFD-020309 Service




NO NO WRFD-020303 Coverage
Inter-RAT Handover Based on Interval Type
Service
NO NO WRFD-020306 Load
Service
Coverage
WRFD-020303 Service

Service

Service
Coverage
WRFD-020303 Service

Service
Service
Service

Coverage
QoS
WRFD-020309 Service
Service
Inter-RAT Handover Based on Type
Service
Service
Load
Service
Load
Service
Service
Service
Service


















NO NO WRFD-020104 Intra Frequency Load Balance Type
NO NO WRFD-020104 Intra Frequency Load Balance Type













NO YES WRFD-020203 Inter RNC Soft Handover Interval Type
MBMS FLC(Frequency Layer

Convergence)/FLD(Frequency Enumeration
NO NO WRFD-010626 Layer Dispersion) Type
NO YES WRFD-020802 OTDOA Based LCS Interval Type


Subscribed Service
Quality Improvement for Enumeration

NO YES WRFD-020128 Subscribed Service Type

NO YES WRFD-020128 Subscribed Service IP Address Type

NO YES WRFD-020128 Subscribed Service IP Address Type

NO YES WRFD-020128 Subscribed Service Interval Type
Quality Improvement for Enumeration

NO YES WRFD-020128 Subscribed Service Type
Subscribed Service
Load Based 3G-2G Handover

YES YES WRFD-070004 Enhancement Based on Iur-g Interval Type
Load Based 3G-2G Handover Enumeration
NO YES WRFD-070004 Enhancement Based on Iur-g Type

NO YES WRFD-070004 Enhancement Based on Iur-g Interval Type
NO YES WRFD-070004 Enhancement Based on Iur-g Interval Type
NO YES WRFD-070004 Enhancement Based on Iur-g
RAN Sharing Introduction Interval Type
WRFD-021304 Package

3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
NO NO None NoneSharing Introduction

RAN Interval Type
WRFD-021304 Package

YES YES WRFD-021301 Connected Mode Interval Type
Connected Mode
MBSC Load Balancing
WRFD- Operator

Connected Mode
MBSC Load Balancing
WRFD- Operator
Enumeration
Enumeration
Enumeration
Enumeration
NO NO WRFD-020106 Load Reshuffling Bit Field Type

Enumeration
Enumeration
Enumeration
NO YES WRFD-020102 Load Measurement Interval Type
Enumeration
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

Phase1
YES YES WRFD-020129 UMTS to LTE Interval Type
Phase1
NO YES WRFD-020129 UMTS to LTE String Type
Phase1
NO YES WRFD-020129 UMTS to LTE Interval Type
Phase1
Phase1
Phase1
Phase1
Phase1

Phase1
Phase1
Phase1
Phase1

Phase1
YES YES WRFD-020129 UMTS to LTE Interval Type
NO YES WRFD-010616 MBMS Introduction Package Interval Type
YES YES WRFD-010616 MBMS Introduction Package String Type
YES YES WRFD-010616 MBMS Introduction Package String Type

Enumeration
Enumeration
WRFD-
WRFD-

MBMS Channel Audience Rating Enumeration
NO YES WRFD-010665 Statistics Type
MBMS Channel Audience Rating Enumeration
NO YES WRFD-010665 Statistics Type

Connected Mode
MBSC Load Balancing
WRFD- Operator

Connected Mode
MBSC Load Balancing
WRFD- Operator
NO YES WRFD-010616 MBMS Introduction

RAN Sharing Package
WRFD-021304 Package

Enumeration
Enumeration
Enumeration
Enumeration
FACH Transmission Sharing for Enumeration
NO NO WRFD-010627 MBMS Type
Enumeration
Enumeration
MBSC Load Balancing
MRFD-211402 MBSC Service Distribution
MBSC Load Balancing

WRFD-211404 Load Based 3G-2G Handover Enumeration
Enhancement
MBSC Load Balancing
WRFD-070004 Enhancement Based on Iur-g Enumeration
NO NO MRFD-211401 NACC Procedure Optimization Type
MBSC Load Balancing

MBSC Load Balancing

MBSC Load Balancing
WRFD- Enumeration
WRFD-
WRFD- Enumeration
WRFD-
WRFD-
WRFD-


Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration


NO YES WRFD-010101 3GPP Specifications Compound Type

YES YES WRFD-070004 Enhancement Based on Iur-g Interval Type
Enumeration
Enumeration
Enumeration

WRFD-050301 Package
Enumeration
Enumeration
Enumeration
YES YES WRFD-050105 ATM Switching Based Hub Node B Interval Type
Enumeration
Overbooking on ATM
Overbooking on ATM

Enumeration
NO YES WRFD-050403 Hybrid Iub IP Transmission Type
Satellite Transmission on Iub Enumeration
Enumeration
NO NO 02130406 on Iub/Iur Interface Type
Enumeration
Enumeration

NO YES 02130406 on Iub/Iur
RAN Interface
Sharing Introduction Type
WRFD-021304 Package
GSM and UMTS Dynamic Enumeration
NO NO MRFD-221802 Spectrum Sharing(UMTS) Type

NO NO WRFD-020107 Overload Control Bit Field Type
WRFD-
NO NO 01061003 HSDPA Admission Control Interval Type
WRFD-
NO NO 01061202 HSUPA Admission Control Interval Type
Enumeration
NodeB Self-discovery Based on IP

NO YES WRFD-031101 Mode Interval Type

NO NO WRFD-031101 Mode String Type
NodeB Self-discovery Based on IP Enumeration

NO NO WRFD-031101 Mode Type

NO YES WRFD-031101 Mode String Type

NO NO WRFD-031101 Mode IP Address Type
NO YES WRFD-031101 Mode IP Address Type
Enumeration


NO YES WRFD-031101 Mode Type
BOOTP
WRFD-031100 NodeB Self-discovery Based on IP
BOOTP
BOOTP
NO NO WRFD-031101 Mode Interval Type
BOOTP
BOOTP
WRFD-031100 NodeB Self-discovery Based on IP Enumeration
BOOTP
BOOTP
BOOTP
BOOTP
BOOTP
NO NO MRFD-211503 Resources Management on MBSC Type
Iub Interface

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration

Enumeration

WRFD-021304 Package
YES YES WRFD-021302 Iu Flex Interval Type
3GPP Specifications
WRFD-010101 Interface Message Tracing
MRFD-210801 Inter RNC Cell Update
WRFD-010802 Inter RNC URA Update
WRFD-021400 establishment (DSCR)
MRFD-210801 Interface Message Tracing
NO YES WRFD-040202 RNC Node Redundancy Bit Field Type

Based on Coverage
WRFD-020301 Intra Frequency Hard Handover Enumeration
Enumeration
SRNS Relocation Introduction
WRFD-020605 Package
WRFD-020203 Inter RNC Soft Handover Enumeration

Enumeration

WRFD-010101 3GPP Specifications
WRFD-010802 Inter RNC Cell Update Enumeration
NO NO WRFD-010902 Inter RNC URA Update Type
WRFD- SRNS Relocation with Hard

NO NO 02060502 Handover Bit Field Type

Package
IP Transmission Introduction on Iur
Direct Signaling Connection Re-Enumeration
NO NO WRFD-021400 establishment (DSCR) Type
Enumeration
NO NO WRFD-010651 HSDPA over Iur Type
Enumeration
NO NO WRFD-010635 HSUPA over Iur Type
Enumeration
WRFD- Enumeration
NO NO 01061019 HSDPA Dynamic Power Allocation Type


Enumeration
3GPP Specifications
YES YES WRFD-010902 Inter RNC URA Update Interval Type

WRFD-020804 LCS Classified Zones
02130401 Operator

Enumeration
Enumeration
Enumeration

Enumeration

Enumeration

NO YES WRFD-020500 Enhanced Fast Dormancy String Type
Enumeration

WRFD-021304 Package

WRFD-021304 Package Enumeration
NO NO WRFD-021311 MOCN Introduction Package Type
WRFD-021302 Iu Flex Enumeration
NO NO WRFD-021311 MOCN Introduction Package Type
NO NO WRFD-021302 Iu Flex Interval Type

WRFD-021304 Package
WRFD-021302 Iu Flex

WRFD-021306 Management
Iu Flex Load Distribution Enumeration
Iu Flex Load Distribution Enumeration



Dedicated Carrier for Each

WRFD- Operator
WRFD-021311 RAN Sharing Introduction Enumeration
WRFD-021311
WRFD-
WRFD- MOCN Mobility Management Enumeration
NO NO 02131104 MOCN Load Banlance Type
WRFD-
02130403 Mobility Control and Service
WRFD- Differentiation
02130401 Dedicated Carrier for Each
WRFD-021311 Operator
WRFD- MOCN Introduction Package Enumeration
NO NO 02131103 MOCN Mobility Management Type
WRFD-
02130403 Mobility Control and Service
WRFD- Differentiation
02130401 Dedicated Carrier for Each
WRFD-021311 Operator
WRFD- MOCN Introduction Package Enumeration
NO NO 02131103 MOCN Mobility Management Type
NO NO WRFD-021311 MOCN Introduction Package Bit Field Type




















Transmission Resources
WRFD-050424 Differentiated Service Based on Enumeration
YES YES WRFD-020806 SPI Weight Type


NO YES WRFD-020806 SPI Weight Interval Type

YES YES WRFD-020806 SPI Weight Interval Type

Traffic Priority Mapping onto Enumeration

YES YES WRFD-050424 Transmission Resources Type



NO NO WRFD-050424 Transmission Resources Type

WRFD- Enumeration
YES YES 01061010 HSDPA Flow Control Type


WRFD-
NO NO 01061010 HSDPA Flow Control Interval Type

YES YES WRFD-020114 (DSAC) Interval Type

WRFD-020107 Overload Control Enumeration
NO NO WRFD-010505 Queuing and Pre-Emption Type

















Enumeration



Cell ID + RTT Function Based Enumeration
NO NO WRFD-020801 LCS Type
Cell ID + RTT Function Based
NO NO WRFD-020801 LCS Interval Type

Paging UE in Idle, CELL_PCH, Enumeration
NO NO WRFD-010301 URA_PCH State (Type 1) Type
Enumeration
Enumeration

Enumeration
NO YES WRFD-040202 RNC Node Redundancy Compound Type

NO NO WRFD-020501 Open Loop Power Control Bit Field Type
NO NO WRFD-021103 Access Class Restriction Interval Type
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
YES YES WRFD-010401 System Information Broadcasting Type

Enumeration
NO YES WRFD-010401 System Information Broadcasting Type
NO YES WRFD-020501 Open Loop Power Control Bit Field Type
NO YES WRFD-010101 3GPP Specifications Bit Field Type


Enumeration
Enumeration
YES YES WRFD-022000 Physical Channel Management Type

WRFD-022000 Physical Channel Management
WRFD-022000 Physical Channel Management


3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
NO NO WRFD-020500 Enhanced Fast Dormancy Interval Type

3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
NO NO WRFD-011402 Encryption Type
NO NO WRFD-011402 Encryption Interval Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Control (DCCC)

Control (DCCC)

Control (DCCC)

Control (DCCC)

Control (DCCC)
Control (DCCC)

Control (DCCC)

Control (DCCC)

Control (DCCC)
Control (DCCC)
Control

Control
Control
Control
Control
Control
Control
Control
Control

Control (DCCC)

Control (DCCC)

Control (DCCC)

Based on DL QoS

Based on DL QoS

Based on DL QoS














Control (DCCC)
Control
Control

Control
Control
NO YES WRFD-020304 Based on DL QoS Interval Type
Control (DCCC)
Control (DCCC)

Control (DCCC)
Control (DCCC)
Control (DCCC)
Control (DCCC)
Control (DCCC)
Enumeration
Enumeration
Enumeration
Enumeration
NO NO WRFD-010505 Queuing and Pre-Emption Interval Type

Enumeration
NO NO WRFD-010505 Queuing and Pre-Emption
RAN Sharing Introduction Type
WRFD-021304 Package

WRFD-010401 System Information Broadcasting



Enumeration

YES YES WRFD-020120 Sharing in RRC Connection Setup Type


Enumeration
YES YES WRFD-020108 Code Resource Management Type
NO YES WRFD-020108 Code Resource Management Interval Type

YES YES WRFD-020114 (DSAC) Type
NO YES WRFD-010101 3GPPSharing

RAN Specifications
Introduction Any Type
WRFD-021304 Package
Enumeration
Enumeration
Enumeration
NO NO WRFD-011000 Cell Broadcast Service Interval Type
NO NO WRFD-011000 Cell Broadcast Service Interval Type

Traffic Load
Traffic Load
Traffic Load
Enumeration
Enumeration
WRFD-
NO NO 01061604 MBMS Soft/Selective Combining Interval Type
NO NO WRFD-010660 MBMS Phase 2 Interval Type
WRFD-
WRFD-
NO NO WRFD-010660 MBMS Phase 2 Interval Type

WRFD-
WRFD-
NO NO 01061602 MBMS Admission Control Interval Type
WRFD- Enumeration
NO NO 01061602 MBMS Admission Control Type
WRFD- Enumeration
WRFD- Enumeration
WRFD- Enumeration
NO NO 01066001 MBMS Enhanced Broadcast Mode Type
NO YES WRFD-040202 RNC Node Redundancy String Type
NO NO WRFD-040202 RNC Node Redundancy Interval Type
NO NO WRFD-040202 RNC Node Redundancy Interval Type
Enumeration
3GPP Specifications

YES YES None None
RAN Sharing Introduction String Type
WRFD-021304 Package
3.4/6.8/13.6/27.2Kbps RRC
YES YES WRFD-010510 Bearer Establishment and Release Type
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
NO NO WRFD-010688 Downlink Enhanced CELL_FACH Type

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
WRFD-010101 3GPP Specifications
NO NO WRFD-020124 Uplink Flow Control of User Plane Bit Field Type


NO NO None NoneSharing Introduction

RAN Interval Type
WRFD-021304 Package

WRFD-021304 Package
Enumeration
WRFD-
WRFD-
NO NO 01066001 MBMS Enhanced
RAN Sharing Broadcast Mode Interval Type
Introduction
WRFD-021304 Package

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


NO YES WRFD-020806 SPI Weight Interval Type

WRFD-020801 LCS
WRFD-020802 OTDOA Based LCS
WRFD-020803 A-GPS Based LCS
NO NO WRFD-020805 LCS over Iur Bit Field Type
Enumeration
Enumeration
NO NO WRFD-020803 A-GPS Based LCS Bit Field Type
NO NO WRFD-020803 A-GPS Based LCS Interval Type

WRFD-020801 LCS
WRFD-020802 OTDOA Based LCS Enumeration

Enumeration
NO NO WRFD-021104 Emergency Call Type
WRFD-020801 LCS
WRFD-020801 LCS
WRFD-020801 LCS
WRFD-020802 OTDOA Based LCS
NO YES WRFD-020801 LCS Interval Type

NO YES WRFD-020801 LCS Type

Enumeration
NO NO WRFD-020807 Iupc Interface for LCS service Type
Enumeration
NO NO WRFD-020807 Iupc Interface for LCS service Type


Enumeration


Enumeration
NO NO WRFD-020802 OTDOA Based LCS Type
Enumeration


NO NO WRFD-020801 LCS String Type

WRFD-020806 SPI Weight
NO NO 02040004 During RAB Setup Interval Type
WRFD- SRNS Relocation (UE Not

NO NO 02060501 Involved) Interval Type

02060501 Involved)
NO NO Interval Type



WRFD- SRNS Relocation (UE Not Enumeration
NO NO 02060501 Involved) Type



WRFD- SRNS Relocation with Cell/URA
NO NO 02060503 Update Interval Type
Based on Coverage
NO NO WRFD-020301 Intra Frequency Hard Handover Interval Type
Based on Coverage
NO NO WRFD-020301 Intra Frequency Hard Handover Interval Type

WRFD-010501 Conversational QoS Class
WRFD-010502 Streaming QoS Class
YES YES WRFD-010504 Background QoS Class Interval Type
WRFD-010503 Interactive QoS Class Enumeration
NO YES WRFD-010504 Background QoS Class Type
3.4/6.8/13.6/27.2Kbps RRC
NO YES WRFD-010510 Bearer Establishment and Release Interval Type
3.4/6.8/13.6/27.2Kbps RRC
NO YES WRFD-020504 Inner Loop Power Control Interval Type
NO YES WRFD-020504 Inner Loop Power Control Interval Type

Coverage
QoS
WRFD-020309 GPRS
WRFD- Inter-RAT Handover Based on
02030802 Service
Coverage
QoS
WRFD-020309 GPRS
WRFD- Inter-RAT Handover Based on
02030802 Service
3.4/6.8/13.6/27.2Kbps RRC

Phase1

WRFD- Control (DCCC) Enumeration
YES YES 01061208 HSUPA DCCC Type





WRFD-
NO NO 01061208 HSUPA DCCC Interval Type
WRFD-
WRFD-
WRFD-



YES YES WRFD-010612 HSUPA Introduction Package Type
Enumeration
Enumeration
Enumeration
NO NO WRFD-010610 HSDPA Introduction Package Interval Type


Enumeration
Enumeration

Enumeration

WRFD- Enumeration
NO NO 01061010 HSDPA Flow Control Type

Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
HSUPA Coverage Enhancement Enumeration

NO NO WRFD-020138 at UE power limitation Type



Enumeration
YES YES WRFD-020503 Outer Loop Power Control Type
Conversational QoS Class

WRFD-010503 Background QoS Class
WRFD-010504 Satellite Transmission on Iub
NO YES WRFD-020503 Outer Loop Power Control Interval Type
WRFD-
NO YES 01061203 HSUPA Power Control Interval Type
WRFD-
WRFD-
WRFD-


Control

Control

Control

Control

Control (DCCC)
NO YES WRFD-021101 Control (DCCC) Interval Type

NO YES WRFD-021101 Control (DCCC) Interval Type

Control
Control (DCCC)

Control
Control (DCCC)
YES YES WRFD-010504 Background QoS Class Type
Enumeration
Conversational QoS Class

WRFD-010503 Background QoS Class
WRFD-010504 Satellite Transmission on Iub
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration


Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
Enumeration
Enumeration
Enumeration

Enumeration

Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration

Enumeration
HSUPA Coverage Enhancement Enumeration

NO NO WRFD-020138 at UE power limitation Type




Enumeration
Enumeration
Enumeration
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
Enumeration
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
3.4/6.8/13.6/27.2Kbps RRC
Phase1
Phase1

Phase1
Phase1

Phase1

Phase1
Phase1
Phase1
NO NO WRFD-011402 Encryption Bit Field Type

(CELL-DCH, CELL-PCH, URA-
NO NO WRFD-010202 PCH, CELL-FACH) Interval Type






WRFD-010202 (CELL-DCH, CELL-PCH, URA-
WRFD- PCH, CELL-FACH) Enumeration
NO NO 01061111 HSDPA State Transition Type
WRFD- Enumeration
WRFD- Enumeration





WRFD-010202 PCH, CELL-FACH)
WRFD- HSUPA DCCC

WRFD- HSUPA DCCC
WRFD- HSUPA DCCC


WRFD-010686 CPC - DTX / DRX Enumeration






Enumeration
Enumeration
Enumeration
Enumeration
Enumeration
Enumeration





WRFD- PCH, CELL-FACH)
NO NO 01061111 HSDPA State Transition Interval Type

NO NO WRFD-010687 CPC - HS-SCCH less operation Interval Type


NO NO WRFD-011401 Integrity Protection Bit Field Type

YES YES WRFD-010101 3GPP Specifications

RAN Sharing Introduction Interval Type
WRFD-021304 Package
NO YES WRFD-050424 Transmission Resources Type


WRFD- Enumeration
YES YES 01061010 HSDPA Flow Control Type
WRFD-
NO NO 01061010 HSDPA Flow Control Interval Type


Enumeration
Enumeration
NO NO WRFD-021104 Emergency Call Type
NO NO WRFD-021104 Emergency Call Bit Field Type

Enumeration

WRFD-050301 Package


Enumeration
Iub Interface
Iub Interface

Enumeration

Enumeration

Enumeration


GUI Value Range
0~2
0~4599
1~4294967295
UNI(UNI Link), IMA(IMA Group), FRAATM(FRAATM Link),

NCOPT(Optical Port), ATMLOGICPORT(ATM Logical Port),
NULL(NULL)
0~11
0~5, 8~27
0~335
0~167
0~31
0~7
0~767
NO(NO), YES(YES)
0~2047
0~4095
32~65535
100~1999
100~1999
PEER(PEER), LOCAL(LOCAL)
0~199
1~64
R99(R99), HSPA(HSPA), SHARE(SHARE)
None
0~4599
0~4294967295
NO(ATM_ADDRESS_DOES_NOT_BELONG_TO_THIS_ADJA
CENT_NODE),
YES(ATM_ADDRESS_BELONGS_TO_THIS_ADJACENT_NO
DE)
5000~30000
5000~30000
2000~60000
2000~60000
2000~60000
2000~60000
2000~60000
5000~30000
5000~30000
0~4599
IUB(Iub Interface), IUR(Iur Interface), IUCS(Iu-CS Interface),

IUPS(Iu-PS Interface)
ATM(ATM), IP(IP), ATM_IP(ATM and IP), HYBRID_IP(HYBRID

IP)
SHARE(SHARE), EXCLUSIVE(EXCLUSIVE)
0~3
0~163
0~163
0~163
0~33
0~63
0~63
0~63
0~4599
None

IUPS(Iu-PS Interface), UNI_AAL2SWITCH(the adjacent node
of the ATM switch on the Iub interface), NNI_AAL2SWITCH(the
adjacent node of ATM switch on Iur or Iu-CS interface)
0~65535
NO(GGSN), YES(SGSN)

IP)
0~186
NO(Not Root Node), YES(Root Node)
0~4599
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~1399
CS1(CS1 Version), CS2(CS2 Version)
1~65535
0~65534
0~250
0~250
0~100
0~100
DISABLE(Disable), ENABLE(Enable)
60~65534
10000~150000
7~90
1~2147483646
1~65535
Critical(Critical), Major(Major), Minor(Minor), Warning(Warning)
ON(ON), OFF(OFF)
0~11
1~32
CLOSE(CLOSE), OPEN(OPEN)
65334~65383
BOOL(BOOL), VALUE(VALUE)
LOW(LOW), HIGH(HIGH)
None
None
1~65535
unshielded(Unshielded), shielded(Shielded)
ON, OFF
30~1024
ON, OFF
0~11
0~5, 8~27
Hub(Hub), Leaf(Leaf)
AEUa, AOUa, UOIa, AOUc, UOIc
0~767
IMA, UNI, FRA, NCOPT, ATMLOGICPORT
0~5, 8~27
0~167
0~335
0~31
0~7
0~767
512~149000
512~149000
SHARE, EXCLUSIVE
0~3
OFF(OFF), ON(ON)
0~1999
0~199
0~767
0~1999
0~199
100~1999
UBR, CBR, RTVBR, NRTVBR, UBR_PLUS
CELL/S, KBIT/S
30~353207
30~353207
30~70754
3~10000
1024~212000
None
0~11
0~27
BFD_OFF(OFF), BFD_ON(ON)
1~65535
nonrpt(Not Report), rpt(Report)
0~11
0~27
SCU, INT
YES(YES)
SCUb
INT, DPU, XPU, OMU, SAU, NIU
PEUa, AEUa, FG2a, GOUa, AOUa, POUa, UOIa, AOUc,

POUc, UOIc, FG2c, GOUc, SPUa, SPUb, DPUb, DPUe,
OMUa, OMUb, OMUc, SAUa, NIUa
OAM, UCP, RUCP, UUP, ATM, IP, SAU, NIU
YES(YES), NO(NO)
0~11
0~27
NO(NO), YES(YES)
LS(Load sharing), BAK(Backup)
1~3
CENTRALIZED(Centralized Power Mode),
DISTRIBUTED(Distributed Power Mode)
0~3
G_15, G_16, G_17, G_18, G_19, G_20, G_21, G_22, G_23,

G_24, G_25, G_26, G_27, G_28, G_29, G_30, G_31
None
G_15, G_16, G_17, G_18, G_19, G_20, G_21, G_22, G_23,
G_24, G_25, G_26, G_27, G_28, G_29, G_30, G_31
None
None
None
None
DISABLE(Disabled), ENABLE(Enabled)
None
None
None
0~11
0~11
0~11
0~5, 8~27
0~7
2~4094
0~499
None
10, 100, 1000
0~11
0~5, 8~27
0~7
0~7
None
0~11
0~11
0~499
LocalMep(LocalMep), RemoteMep(RemoteMep)
1~1000
ETHER, TRUNK
0~5, 8~27
0~11
0~11
MPS, EPS
1~11
0~27
AEUa, PEUa, AOUa, POUa, UOIa, AOUc, POUc, UOIc
0~31
NO(NO), YES(YES)
0~31
NO(NO), YES(YES)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
MANUAL(Manual Handover), AUTO(Auto Handover),
FREE(Free-run)
1~4
1~4
BITS1-2MHZ(2MHZ Building Integrated Timing Supply system

1), BITS2-2MHZ(2MHZ Building Integrated Timing Supply
system 2), BITS1-2MBPS(2MBPS Building Integrated Timing
Supply system 1), BITS2-2MBPS(2MBPS Building Integrated
Timing Supply system 2), 8KHZ(8KHZ), GPS(Globe Positioning
System), LINE1_8KHZ(8KHZ line1), LINE2_8KHZ(8KHZ line2),
BITS1-1.5MBPS(1.5MBPS Building Integrated Timing Supply
system 1), BITS2-1.5MBPS(1.5MBPS Building Integrated
Timing Supply system 2)
GCUa, GCGa
ON(ON), OFF(OFF)
ALL(ALL Type), ONLY_SSL(Only SSL Connection)
0~11
0~5, 8~27
AOUa, POUa, AOUc, POUc
ALL(Select all E1/T1 ports), PORT(Select all E1/T1 ports of one

channelized optical port), SINGLE(Select one E1/T1 port)
0~3
0~83
NULL, 1BYTE, 16BYTE, 64BYTE
Hexadecimal(Hex decimal), Character_String(Character String)
None
None
ZERO(zero), SPACE(space)
0~65535
OFF(OFF), SERVICE-BASED(SERVICE-BASED), LOAD-

BASED(LOAD-BASED), DYNAMIC-BASED(DYNAMIC-
BASED)
-100~100
-100~100
SCU, GCU, MPU, UCP, DPU, INT, NIU
20~99
30~100
20~99
30~100
20~99
30~100
NBAP_CCP, NBAP_NCP, IUB_OAM, ALCAP
0~100
None
0~11
0~5, 8~27
LOGIC_IP(Logical IP Address), IPOA_CLIENT_IP(IPOA Client
IP Address)
None
None
776~1696
0~63
None
0~63
0~7
0~11
0~5, 8~27
AEUa, AOUa, AOUc, PEUa, POUa, POUc

ALL(Select all ports), SINGLE(Select one port)
0~335
NO(NO), YES(YES)
E1_UNBA(E1 Unbalance), E1_BA(E1 Balance), T1(T1), E1(E1)

E1_DOUBLE_FRAME(E1_DOUBLE_FRAME),
E1_CRC4_MULTI_FRAME(E1_CRC4_MULTI_FRAME),
T1_SUPER_FRAME(T1_SUPER_FRAME),
T1_EXTENDED_SUPER_FRAME(T1_EXTENDED_SUPER_F
RAME)
RAME)
RAME)
B8ZS(B8ZS), HDB3(HDB3), AMI(AMI), AMI_ZCS(AMI_ZCS)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
None
0~11
0~5, 8~27
AEUa, AOUa, AOUc, PEUa, POUa, POUc
0~335
NO_LOOP(No loop), REMOTE_LOOP(Remote loop),

LINE_REM_LOOP(Line remote loop), LOCAL_LOOP(Local
loop), PAYLOAD_LOOP(payload loop), SIN_CHN_LOC(single
channel local loop), SIN_CHN_REM(single channel remote
loop)
TS4(Time_slot_4), TS5(Time_slot_5), TS6(Time_slot_6),
TS10(Time_slot_10), TS11(Time_slot_11),
TS30(Time_slot_30), TS31(Time_slot_31)
1~65535
None
None
None
None
0~11
CLOSE(Close), OPEN(Open)
VOLTAGE(Voltage), CURRENT(Current)
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1~65535
None

power(Power System), env(Environment System), sig(Signaling
System), trunk(Trunk System), hardware(Hardware System),
software(Software System), run(Running System),
comm(Communication System), service(QoS),
handle(Processing Error), integrity(Integrity), ope(Operational),
physical(Physical), sec(Security), time(Time domain)
0~11
0~5, 8~27
0~11
0~5
None
None
None
0~11
0~5, 8~27
FG2a, GOUa, FG2c, GOUc
FE, GE
0~11
ENABLE, DISABLE
1000M(1000M), AUTO(AUTO)
256~1650
OFF(OFF), ON(ON)
0~100
OFF(OFF), ON(ON)
0~1999
OFF(OFF), ON(ON)
O1E3_R5E4(OCCUR:1E-3, RECOVERY:5E-4),
O5E6_R1E6(OCCUR:5E-6, RECOVERY:1E-6)
80~2000
80~2000
V7(Draft V7), V8(Standard Version)
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~11
0~11
0~5, 8~27
0~11
LOAD_SHARING(Load sharing), ACTIVE_STANDBY(Active
standby)
0~65535
NON-REVERTIVE(NON-REVERTIVE),
REVERTIVE(REVERTIVE)
STATIC_LACP, MANUAL_AGGREGATION
0~100
OFF(OFF), ON(ON)
0~1999
V7(Draft V7), V8(Standard Version)
0~11
0~5, 8~27
0~11
0~5
None
None
0~11
0~5, 8~27
0~11
0~5, 8~27
0~11
LOAD_SHARING(Load sharing), ACTIVE_STANDBY(Active
standby)
0~65535
10~15
30~35
OFF(OFF), ON(ON)
NORMAL_FAN(Normal Fan), IND_FAN(Independent Fan)
0~11
HW_AUTO_TEMPERATURE_CONTROL(Auto Temperature
Control), SPECIFY_RATE(Specify Rate),
SOFTWARE_CONTROL(Software Control)
55~100
SCU, GCU, XPU, DPU, INT, NIU
2~2000
1~1000
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
1~100
1~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
2~2000
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
ON, OFF
0~100
ON, OFF
ON, OFF
ON, OFF
ON, OFF
0~11
0~5, 8~27
0~31
0~335
FRAATM, FRAIMA
0~31
OFF(OFF), ON(ON)
0~1999
0~199
OFF(OFF), ON(ON)
0~199
1024~65535
1024~65535
None
None
AUTO(Auto), PLAINTEXT(Plain Text), ENCRYPTED(SSL
Encrypte)
YES(Support), NO(Not Support)
None
21~65535
1024~65535
1024~65535
AUTO(Automatic), PLAINTEXT(Plain Text), ENCRYPTED(SSL

Encrypted)
DEFAULTPORT(Default 21 Port), CUSTOMPORT(Custom

Port)
1024~65535
1024~65535
OFF(Disable the golbal route management), ON(Enable the

golbal route management)
0~65534
RNC(Local RNC), NODEB(NodeB in Local RNC),
NRNC_RNC(Neighboring RNC), NRNC_NODEB(NodeB in
Neighboring RNC)
0~4095
0~65535
1~60
1~60
DEG(DEG), SEC(SEC)
MET(Metric), IMP(Imperial)
-90000000~90000000
-180000000~180000000
-1000~10000
None
None
-3281~32810
1~60
1~60
0~11
0~5, 8~27
None
None
ECHOREPLY(Ping_reply), UNREACH(Unreachable),
SOURCEQUENCH(Source_quench), REDIRECT(Redirect),
ECHO(Ping_request),
ROUTERADVERT(Router_advertisement),
ROUTERSOLICIT(Router_solicitation),
TIMXCEED(Time_exceeded),
PARAMPROB(Parameter_problem),
TSTAMP(Timestamp_request),
TSTAMPREPLY(Timestamp_reply),
IREQ(Information_request), IREQREPLY(Information_reply),
MASKREQ(Address_mask_request),
MASKREPLY(Address_mask_reply)
0~11
0~5, 8~27
AEUa, AOUa, AOUc
0~167
1~32
0~255
D32, D64, D128, D256
4~255
V1.0(V1.0), V1.1(V1.1)
OFF(OFF), ON(ON)
0~1999
3~505
0~199
OFF(OFF), ON(ON)
0~199
0~11
0~5, 8~27
0~335
0~5, 8~27
0~167
IU(Restore Fault of IU), IUB(Restore Fault of IUB),
IP_PATH(Restore Fault of IP Path), AL(Restore Fault of AL),
GTPU(Restore Fault of GTPU), CELL_KPI(Restore Fault of
Cell KPI), SIGNALING_PLANE_LOOP(Restore Fault of
Signaling Plane Loop), SHB(Restore Fault of Strong Heart
Beat)
AOUA(AOUA), POUA(POUA), UOIA_ATM(UOIA_ATM),
UOIA_IP(UOIA_IP), FG2A(FG2A), GOUA(GOUA),
GOUC(GOUC), POUC(POUC), FG2C(FG2C),
UOIC_ATM(UOIC_ATM), AOUC(AOUC)
AOUA(AOUA), POUA(POUA), UOIA_ATM(UOIA_ATM),
UOIA_IP(UOIA_IP), FG2A(FG2A), GOUA(GOUA),
AEUA(AEUA), PEUA(PEUA), GOUC(GOUC), POUC(POUC),
FG2C(FG2C), UOIC_ATM(UOIC_ATM), AOUC(AOUC)
OFF(OFF), ON(ON)
10~100
1~10
10~100
1~10
1~10000
1~10000
1~100
1~10
1~20
1~20
1~20
1~5
OFF(OFF), ON(ON)
60~3600
10~100
0~11
0~5, 8~27
FG2a, GOUa, FG2c, GOUc

OFF(OFF), ON(ON)
20~20000
20~20000
OFF(OFF), ON(ON)
0~11
0~5, 8~27
FG2a, GOUa, UOIa, FG2c, GOUc, POUc
Hub(Hub), Leaf(Leaf)
0~988, 1024~1535
ETHER, IPLOGICPORT, TRUNK, PPP, MP
0~11
512~1535
0~11
0~499
0~167
SHARE, EXCLUSIVE
0~3
OFF(OFF), ON(ON)
1~1562
1~1562
0~100
1~1562
4500~32767
0~100
0~100
0~1000
1~100
1~100
100~1000
0~1000
1~100
0~10000
1~100
0~100
0~15
0~15
OFF(OFF), ON(ON)
0~1999
20~99
20~99
0~199
OFF(OFF), ON(ON)
0~199
FPMUX, UDPMUX
0~4599
0~65535
NO(NO), YES(YES)
BE(BE), AF11(AF11), AF12(AF12), AF13(AF13), AF21(AF21),
AF22(AF22), AF23(AF23), AF31(AF31), AF32(AF32),
AF33(AF33), AF41(AF41), AF42(AF42), AF43(AF43), EF(EF)
16~1023
24~1031
1~30
NORTPCOMP, RTPCOMP
NORTPCOMP, RTPCOMP
0~12999
FPMUX, UDPMUX
None
None
IMA(IMA Group), UNI(UNI Link), FRAATM(FRAATM Link),
NCOPT(Optical Port), ATMLOGICPORT(ATM Logical Port),
NULL(NULL)
0~5, 8~27
0~167
0~335
0~31
0~7
0~767
0~4095
32~65535
100~1999
100~1999
IUB, IUPS, OTHER
0~4599
0~65535
IP(IP), HYBRID_IP(HYBRID IP)
QoS(QoS), BE(BE), AF11(AF11), AF12(AF12), AF13(AF13),

AF43(AF43), EF(EF), LQ_QOS(LQ_QOS), LQ_BE(LQ_BE),
LQ_AF11(LQ_AF11), LQ_AF12(LQ_AF12),
LQ_AF42(LQ_AF42), LQ_AF43(LQ_AF43), LQ_EF(LQ_EF)
None
None
None
1~3000000
1~3000000
NULL(NULL), IPLGCPORT(IP Logic Port), RSCGRP(Resource
Group)
0~5, 8~27
0~988
0~2047
0~199
2~4094
ENABLED(Enabled), DISABLED(Disabled)
None
1~60
1~5
44~1024
UDP(UDP), ICMP(ICMP)
0~4599
0~65535
0~11
0~5, 8~27
0~511
0~11
0~5, 8~27
None
None
None
HIGH, LOW
None
None
0~11
0~5, 8~27
None
None
None
0~511
0~11
0~27
NORMAL(Normal), FORCE(Force)
None
None
90~99
70~95
UMTS(UMTS)
NO(NO), YES(YES)
0~3
0~100500
0~24000000
0~24000000
0~24000000
0~24000000
0~30
0~176400
0~30
0~176400
0~632400
PDCP(PDCP Header compression), AMRC(AMR voice coding
rate control), TFOTRFO(TFO/TrFO), INDIRECRETRY(Intra
system Direct Retry), INTERRATDIRECRETRY(Inter system
Direct Retry), INTERRATREDIRECT(Inter system Redirect),
CBS(Cell broadcast service), CELLID(Cell ID LCS),
OTDOA(OTDOA LCS), AGPS(AGPS LCS), PUC(Potential user
control), INTRACELLLDB(Intra frequency load balancing),
INTERCELLLDB(Inter frequency load handover),
MULTIRAB(Multiple RAB), HCS(Hierarchical Cell Structure),
RABDOWNSIZING(RAB Downsizing at Admission Control),
QCPE(Queuing and Pre-emption), INTERSERVICEHO(Inter
system Service Handover), INTERLOADHO(Inter system Load
Handover), IUQOSRENEG(RAB Quality of Service
Renegotiation over Iu), LCSCZ(LCS Classified Zones),
HSDPA(High Speed Downlink Packet Access), IUFLEX(IU
FLEX), IUBSC(Satellite Communication in Iub Interface),
IUBIP(IP Transportation in Iub Interface), MBMS(MBMS
Function)
WBAMR(Wide Band AMR), HSUPA(High Speed Uplink Packet

Access), RANSHARE(RAN Sharing Function),
HSDPA3.6M(High Speed Downlink Packet Access Function
3.6M), HSDPA7.2M(High Speed Downlink Packet Access
Function 7.2M), ROHC(PDCP ROHC Function), IURLC(LCS
over Iur), NACC(Network Assisted Cell Change), PSHBUG(PS
Handover Between UMTS and GPRS), IMSIBH(IMSI Based
Handover), 32HSDPAUPERCELL(32 HSDPA Users per Cell),
64HSDPAUPERCELL(64 HSDPA Users per Cell),
STMTRAONHSDPA(Streaming Traffic Class on HSDPA),
HSDPASTATETRAN(HSDPA State Transition),
HSDPADRD(HSDPA DRD), ENHANCEDIUFLEX(Enhanced Iu
Flex), STMTRAONHSUPA(Streaming Traffic Class on
HSUPA), ATMIPDUALSTACK(IUB ATM/IP Dual Stack
Transportation Function), IPTRANINIUR(IP Transportation in
Iur Interface ), IPTRANINIU(IP Transportation in Iu Interface),
FRACTIONALIP(Fractional IP), IPIUBOVERBOOKING(IP IUB
overbooking Function), FRACTIONALATM(Fractional ATM),
ATMOVERBOOKING(ATM IUB overbooking Function),
IUBHYBRIDIPTRAN(IUB Hybrid IP Transportation Function),
MBMS8CHANNELPERCELL(MBMS 8 Channels per Cell),
256KBPSCHNLRATEONMBMS(256Kbps Channel Rate on
MBMS), MBMSFLCFLD(MBMS FLC/FLD), VTFTSFIHO(Video
Telephony Fallback to Speech AMR for Inter-RAT HO),
CBIHBUMTSANDGSMGPRS(Coverage Based Inter-RAT
Handover Between UMTS and GSM/GPRS),
SRNSRELOCATION(SRNS Relocation),
SRNSRWHHANDOVER(SRNS Relocation with Hard
Handover)
SRNSRWCUPDATE(SRNS Relocation with Cell/URA Update),
LOSSLESSSRNSRELCT(Lossless SRNS Relocation),
INTERFREQHARDHNDV(Inter frequency hard handover),
IMPRVEDWNLNKCVRGE(Improved Downlink Coverage),
ACRWHENSPUOVER(Access Class Restriction when SPU
overload), CBWHENIUIFAULT(Cell Barring when IU in fault),
3G2GCOMMON_LOAD(3G/2G Common Load Management),
FP_MUX(FP MUX), HSDPA_OVER_IUR(HSDPA over Iur),
HS_DPCCH_PREAMBLE_SUPPORT(HS-DPCCH Preamble
support), HSUPA_2ms_10ms(HSUPA 2ms/10ms TTI
handover), HSUPA_5_74MBPS(HSUPA 5.74Mbps per User),
HSUPA_OVER_IUR(HSUPA over Iur),
HUB_IUB_OVERBOOKING(HUB IUB overbooking Function),
IMS_SIGNALING_OVER_HSPA(IMS Signaling over HSPA),
DYN_BANDWIDTH_CTROL_IUB_IP(Dynamic Bandwidth
Control of Iub IP), MBMS_OVER_IUR(MBMS over Iur),
MBMS_P2P_OVER_HSDPA(MBMS P2P over HSDPA),
MBMS_ENHANCED_BROADCAST(MBMS Enhanced
Broadcast Mode), MBMS_ADMISSION_ENHANCE(MBMS
Admission Enhancement),
RAN_SHARING_ENHANCED_PACKAGE(RAN Sharing
Enhanced Package), SRB_OVER_HSDPA(SRB over HSDPA),
SRB_OVER_HSUPA(SRB over HSUPA), MULTI_FBNM(Multi
Frequency Band Networking Management),
HSDPA_13_976MBPS(HSDPA 13.976Mbps per User),
BFD_ARP_IP(IP Fault Detection based on BFD),
INTER_FHHBDLQOS(Inter Frequency Hard Handover Based
on DL QoS), INTER_RHBDLQOS(Inter-RAT Handover Based
on DL QoS), MBMS_16_CHANNELS_PER_CELL(MBMS 16
Channels per Cell), 60_HSUPA_USERS_PER_CELL(60
HSUPA Users per Cell), TPMT(Traffic Priority Mapping on
Transport), AQM(Active Queue Management)
DYNAMIC_POWER_ESTIMATION_FOR_MTCH(Dynamic
Power Estimation for MTCH), ONE_TUNNEL(One Tunnel),
MULCAR_SWOFF_BASEDON_TRALOAD(Multi-carrier switch
off based on traffic load), CS_OVER_HSPA(CS voice over
HSPA), VOIP_OVER_HSPA(VoIP over HSPA Introduction
Pakage), 96_HSDPA_USERS_PER_CELL(96 HSDPA Users
per Cell), HSPA_DOWN28_PER_USER(HSPA + Downlink 28
Mbit/s Per User), HSPA_DOWN21_PER_USER(HSPA +
Downlink 21 Mbit/s Per User),
96_HSUPA_USERS_PER_CELL(96 HSUPA Users per Cell),
MSCH_SCHEDULING(MSCH Scheduling),
MBMS_CHANNEL(MBMS Channel Audience Rating Statistics),
ENHANCED_CELL_FACH(Enhanced CELL_FACH),
CPC_HS_SCCH(CPC-HS-SCCH Less Operation),
CPC_DTX_DRX(CPC-DTX / DRX),
UPLINK_MACRO_RECEIVE(Uplink Macro Diversity Intelligent
Receiving), DOMAIN_ACCESS_CONTROL(Domain Specific
Access Control), SERVICE_IN_RRC(Service Steering in RRC
Connection Setup), TCP_ACCELERATOR(TCP Accelerator),
UPLINK_CONTROL_OF_USER(Uplink Flow Control of User
Plane), MOCN_PACKAGE(MOCN Introduction Package),
IUCS_UDP_MUX(UDP MUX for Iu-CS Transmission),
RNC_NODE_REDUNDANCY(RNC Node Redundancy),
DOWNLNK_ENHANCED_L2(Downlink Enhanced L2),
DIFF_SERVICE_ON_SPI_WEIGHT(Differentiated Service
Based on SPI Weight),
HSUPA_ADAPTIVE_RETRANSMISSION(HSUPA Adaptive
Retransmission), SIMPLE_CELL_BORADCAST(Simplified Cell
Broadcast), SATELLITE_TRANS_ON_IU(Satellite
Transmission on Iu Interface), IUR_G_NACC(NACC Procedure
Optimization Based on Iur-g), IUR_G_LBB(BSC Load
Balancing Based on Iur-g), IUR_G_SDB(BSC Service
Distribution Based on Iur-g)
IUR_G_HBL(Handover Based on Load on Iur-g),
EHSPA_42M_DL(HSPA+ Downlink 42 Mbit/s per User),
UL_MOBILITY_P1(Mobility between UMTS and LTE Phase 1),
HSDPA_128_UPC(128 HSDPA Users per Cell),
HSUPA_128_UPC(128 HSUPA Users per Cell),
IUPC_FOR_LCS(Iu PC interface for LCS),
MULTI_FREQ_BNM_EH(Enhancement for Multi frequency
band Networking management),
WARN_OF_DISASTER(Warning of Disaster),
QUAL_IMPROVE_FOR_SS(Quality Improvement for
Subscribed Service), TTI_FOR_BE_SBC(TTI Switch for BE
Services Based on Coverage),
INTERSYS_REDIRECT_BOD(Inter System Redirect Based on
Distance), MEASUREMENT_BD_RETRY(Measurement Based
Direct Retry), FAST_DORMANCY_ENHANCE(Fast Dormancy
Enhancement), HSUPA_COVERAGE_ENHANCE(HSUPA
Coverage Enhancement at UE power limitation),
ENHANCE_UL_FOR_CELL_FACH(Uplink Enhanced
CELL_FACH), ENHANCE_DRX(Enhanced DRX),
HSPA_DL84M_PER_USER(HSPA+ Downlink 84Mbit/s per
User), HSPA_UL11.5M_PER_USER(HSPA+ Uplink 11.5Mbit/s
per User), PS_SERVICE_REDIRECT_FU2L(PS Service
Redirection from UMTS to LTE),
VIDEO_PHONE_RESTRICT(Videophone Service Restriction),
OPT_R99HSUPA_USER_FAIRNESS(Optimization of R99 and
HSUPA Users Fairness),
ADAPTIVE_CONF_TC_PO_HSUPA(Adaptive Config of Traffic
Channel Power offset for HSUPA),
WEB_BROWSING_ACCELERATION(Web Browsing
Acceleration), P2P_RATE_CONTROL(P2P Rate Control),
FREE_USER_RESOURCE_RESERVE(Free User Resource
Reservation), FLEX_HSPA_TECH_SELECTION(Flexible
HSPA+ Technology Selection)
None
ON(ON), OFF(OFF)
1~63
None
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
LFB(Load from OMU and write flash), CL(Consult Load)
monitor, host_gate, ems_gate, authority, configure, maintain,

stat, alarm, software, ftp_server, sntp, ems_agent,
omu_manager, weblmt, cfa, debug_log
TASKID(Task ID), CMDCODE(Command Code)
0~65535
0~65535
7~365
10000~50000
OPLOG_TYPE(Operation Log), SECLOG_TYPE(Security Log)
0~186
0~186
0~186
M3UA_SGP(M3UA SGP), M3UA_IPSP(M3UA IPSP),

M3UA_SS7SP(M3UA SS7SP), M3UA_SP(M3UA SP)
0~4294967295
None
0~186
0~4
M3UA_ASP(M3UA_ASP), M3UA_IPSP(M3UA_IPSP)
0~4294967295
None
0~186
0~186
B0000(B0000), B0001(B0001), B0010(B0010), B0011(B0011),
B0100(B0100), B0101(B0101), B0110(B0110), B0111(B0111),
B1000(B1000), B1001(B1001), B1010(B1010), B1011(B1011),
B1100(B1100), B1101(B1101), B1110(B1110), B1111(B1111)
M3UA_OVERRIDE_MOD(Active/Standby Mode),
M3UA_LOADSHARE_MOD(Load Sharing Mode)
M3UA_ASP(M3UA_ASP), M3UA_IPSP(M3UA_IPSP)
1~10
None
0~186
0~15
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26

0~7
0~1199
0~99
M3UA_MASTER_MOD(M3UA_MASTER_MOD),
M3UA_SLAVE_MOD(M3UA_SLAVE_MOD)
None
0~186
0~186
0~99
None
MEASRST(MEASRST), HOSTRST(HOSTRST)
0~14
500~5000
0~11
0~5, 8~27
PEUa, POUa, POUc
IP
0~167
MLPPP, MCPPP
NO(NO), YES(YES)
None
None
None
None
LONG(LONG), SHORT(SHORT)
4, 8
128~1024
No_HC(No_HC), UDP/IP_HC(UDP/IP_HC),
RTP/UDP/IP_HC(RTP/UDP/IP_HC)
Disable(Disable), Enable(Enable)
1~746
1~1500
1~1500
OFF(OFF), ON(ON)
0~1999
0~100
NO_V(NO_V), PAP_V(PAP_V), CHAP_V(CHAP_V)
SERVER(SERVER), CLIENT(CLIENT)
None
None
0~199
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
ERR_PFM_5E6(OCCUR:5E-6), ERR_PFM_1E5(OCCUR:1E-
5), ERR_PFM_5E5(OCCUR:5E-5),
ERR_PFM_5E3(OCCUR:5E-3)
ERR_PFM_1E6(RECOVERY:1E-6),
ERR_PFM_1E3(RECOVERY:1E-3)
OFF(OFF), ON(ON)
0~199
4, 8
1~746
1~1500
1~1500
ERR_PFM_5E3(OCCUR:5E-3)
ERR_PFM_1E3(RECOVERY:1E-3)
0~11
0~5, 8~27
PEUa, POUa, POUc
0~167
0~499
0~335
2~5
1~30
None(None), 16bit(16bit), 32bit(32bit)
0~11
0~27
0~11
0~27
0~11
0~27
0~7
NON-REVERTIVE(NON-REVERTIVE),
REVERTIVE(REVERTIVE)
30~60000
NOT-INDICATE-END(NOT-INDICATE-END), INDICATE-
END(INDICATE-END)
DISABLE, ENABLE
1E-3, 1E-4, 1E-5, 1E-6, 1E-7, 1E-8, 1E-9
HIGH(HIGH), LOW(LOW)
MODE1(1:1 Protection Switching), MODE2(1+1 Unidirectional
Protection Switching), MODE3(1+1 Bidirectional Protection
Switching), MODE4(Y Line)
0~11
0~27
0~7
CLEAR(Cleared), LOP(Lockout of Protection), FS(Forcibly
switchover working link to protection link), MS(Manual
switchover from working link to protection link),
EXERS(Exercisely switch working link to protection link)
0~186
0~186
B0000(B0000), B0001(B0001), B0010(B0010), B0011(B0011),

B0100(B0100), B0101(B0101), B0110(B0110), B0111(B0111),
B1000(B1000), B1001(B1001), B1010(B1010), B1011(B1011),
B1100(B1100), B1101(B1101), B1110(B1110), B1111(B1111)
OFF(OFF), ON(ON)
None
0~186
0~15
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~1399
0~99
1~15
1~254
None
0~186
0~186
0~99
None
800~1200
1400~2000
800~1200
800~1200
800~1200
800~1200
30000~60000
800~1500
800~1500
2000~3000
800~1500
180000~360000
180000~360000
8000~12000
30000~90000
35000~120000
None
0~186
0~4
WNF(Whole Number Format), DNF(Divided Number Format)
1~16777215
None
IUCS(IUCS), IUPS(IUPS), IUR(IUR),

IUCS_RANAP(IUCS_RANAP), IUCS_ALCAP(IUCS_ALCAP),
AAL2SWITCH(AAL2SWITCH), STP(STP), IUPC(IUPC)
B0000(B0000), B0001(B0001), B0010(B0010), B0011(B0011),
B0100(B0100), B0101(B0101), B0110(B0110), B0111(B0111),
B1000(B1000), B1001(B1001), B1010(B1010), B1011(B1011),
B1100(B1100), B1101(B1101), B1110(B1110), B1111(B1111)
NO(NO_DIRECT_CONNECT), YES(DIRECT_CONNECT)
OFF(OFF), ON(ON)
MTP3(MTP3), M3UA(M3UA), MTP3_M3UA(MTP3 and M3UA)
M3UA_FIRST(M3UA_FIRST), MTP3_FIRST(MTP3_FIRST)
ITUT(ITUT), ANSI(ANSI), TTC(TTC)

ALL(Shield by Alarm ID), BOARD(Shield by Board),
PORT(Shield by Port), DSP(Shield by DSP)
0~11
0~27
0~335
0~27
ALL(All), ONEBYONE(One by One)
1~65535
None
None
None
None
None
None
None
None
Administrators(Administrator), Operators(Operator),
Users(User), Guests(Guest), Customs(Custom)
G_0, G_1, G_2, G_3, G_4, G_5, G_6, G_7, G_8, G_9, G_10,
G_11, G_12, G_13, G_14, G_15, G_16, G_17, G_18, G_19,
G_20, G_21, G_22, G_23, G_24, G_25, G_26, G_27, G_28,
G_29, G_30, G_31
NOLIMIT(No Limit), LIMIT(Limit)
year, month, day
year, month, day
hour, min, sec
hour, min, sec
NOLIMIT(No Limit),
SUN(Sunday), LIMIT(Limit)TUE(Tuesday),
MON(Monday),
WED(Wednesday), THU(Thursday), FRI(Friday),
SAT(Saturday)
None
Administrators(Administrator), Operators(Operator),
Users(User), Guests(Guest), Customs(Custom)
None
0~4
INT(INT), INTB(INTB), NAT(NAT), NATB(NATB)
BIT14(BIT14), BIT16(BIT16), BIT24(BIT24)
WNF(Whole Number Format), DNF(Divided Number Format)
1~16777215
None
OFF(OFF), ON(ON)
OFF(Unlock), ON(Lock)
0~199
ONE(One), TWO(Two), THREE(Three), FOUR(Four)
ATM(ATM), IP(IP)
UMTS(UMTS)
0~3
0~100
0~199
0~3
0~100
0~199
0~3
0~100
0~199
0~3
0~100
0~199
OFF(Off), ON(On)
0~11
0~5, 8~27
AOUa, POUa, UOIa, AOUc, UOIc, POUc
ALL(Select all ports), SINGLE(Select one port)
0~7
OFF(OFF), ON(ON)
SDH, SONET
LUCENT_MODE, HUAWEI_MODE, ALCATEL_MODE
UNI, NNI
NULL, 1byte, 16byte, 64byte

None
None
None
None
0~15
OFF(OFF), ON(ON)
0~1999
ZERO(zero), SPACE(space)
AU4(AU4), AU3(AU3)
0~11
0~5, 8~27
0~7
NO_LOOP(NO_LOOP), LOCAL_LOOP(LOCAL_LOOP),
REMOTE_LOOP(REMOTE_LOOP)
One_touch(execute on all boards in all subracks),
Step_by_Step
SCUa, SCUb, GCUa, GCGa, PEUa, AEUa, FG2a, GOUa,

AOUa, POUa, UOIa, AOUc, POUc, UOIc, FG2c, GOUc, SPUa,
SPUb, DPUb, DPUe, NIUa
UCP, RUCP, UUP, ATM, programme

MAINCPU_PATCH(Main IP, NIU patch),
DSP_PATCH(DSP programme patch),
UCODE_PATCH(Marcrocode patch)
0~11
0~5, 8~27
BE(BE), AF11(AF11), AF12(AF12), AF13(AF13), AF21(AF21),
AF33(AF33), AF41(AF41), AF42(AF42), AF43(AF43), EF(EF)
0~63
10~1999
IP, ATM
0~5
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
10~150
0~11
0~5, 8~27
PEUa, POUa, UOIa, POUc
IP
0~499
0~335
NO(NO), YES(YES)
None
None
None
None
No_HC(No_HC), UDP/IP_HC(UDP/IP_HC),
RTP/UDP/IP_HC(RTP/UDP/IP_HC)
1~746
1~1500
1~1500
NO_V(NO_V), PAP_V(PAP_V), CHAP_V(CHAP_V)
SERVER(SERVER), CLIENT(CLIENT)
None
None
2~5
1~30
OFF(OFF), ON(ON)
0~100
0~1999
None(None), 16bit(16bit), 32bit(32bit)
0~199
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~199
1~1500
0~11
0~5, 8~27
PPP, MPGRP
0~167
0~499
NO_LOOP(No loop), SELF_LOOP(Self loop)
1~65535
6~32
LOWERCASE(Lowercase), UPPERCASE(Uppercase),
DIGIT(Digit), SPECHAR(Special character)
1~255
1~65535
1~60
1~999
1~255
1~10
2~32
OFF(Close), ON(Open)
0~11
BIT0(NO.1_-48V_INPUT_ALARM), BIT1(NO.2_-
48V_INPUT_ALARM),
BIT6(NO.1_OUTPUT_CONTROL_SWITCH_ALARM),
BIT14(NO.1_EXTERAL_BOOLEAN_VALUE_SENSOR_ALAR
M),
M),
M),
M), BIT22(NO.5_OUTPUT_CONTROL_SWITCH_ALARM),
BIT31(NO.11_OUTPUT_CONTROL_SWITCH_ALARM)
BIT9(NO.3_-48V_INPUT_ALARM), BIT10(NO.4_-
48V_INPUT_ALARM), BIT11(NO.5_-48V_INPUT_ALARM),
BIT12(NO.6_-48V_INPUT_ALARM)
0~11
55~59
40~45
55~59
40~45
55~59
40~45
55~59
40~45
55~59
40~45
55~59
40~45
0~11
0~5, 8~27
0~63
0~63
0~63
0~63
0~63
OFF(OFF), ON(ON)
0~63
OFF(OFF), ON(ON)
SINGLE(Select single rolllback point), ALL(Select all rollback
point)
None
None
0~65535
ASC0, ASC1, ASC2, ASC3, ASC4, ASC5, ASC6, ASC7
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~2047
ATM(ATM), IP(IP)
NO(NO), YES(YES)
0~2047
SHARE(SHARE), EXCLUSIVE(EXCLUSIVE)
0~3
FULL_DUPLEX(Full Duplex), HALF_DUPLEX(Half Duplex)
0~4000000
0~4000000
0~4000000
0~199
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~1399
UNI(UNI), IMA(IMA), FRAATM(FRAATM), NCOPT(NCOPT),

ATMLOGICPORT(ATMLOGICPORT), NULL(NULL)
0~11
0~5, 8~27
0~335
0~167
0~31
0~7
0~767
0~4095
32~65535
100~1999
100~1999
UNI(UNI), NNI(NNI)
MPS_EMERGENCY(MPS_EMERGENCY),
MPS_NORMAL(MPS_NORMAL),
MPS_NEUTRAL(MPS_NEUTRAL)
100~1000
50~10000
100~30000
1200~20000
100~1200, 1000~3000
1~7
30~90
10~200
45~90
1200~2000
0~10
4~8
25~50, 250~500
3~67
10~2000
1~32767
60~120
60~600
180~1260
10~20
10~20
30~90
1380~1500
10~20
10~20
30~90
60~120
30~90
10~50
10~20
10~20
1~30
None
1~30
None
DISABLED(Prohibit to Use), ENABLED(Available)
0~65535
0~255
-350~150
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~1199
SERVER(SERVER MOD), CLIENT(CLIENT MOD)
NBAP(NBAP), M3UA(M3UA)
0~63
1024~65535
None
None
None
None
1024~65535
NO(NO), YES(YES)
0~5, 8~27
0~988
50~60000
50~60000
50~60000
0~100
0~100
0~500
1000~600000
0~254
0~254
NO(NO), YES(YES)
NO(NO), YES(YES)
ALDER32(ALDER32), CRC32(CRC32)
500~1500
DISABLE(DISABLE), ENABLE(ENABLE)
2~4094
DISABLE(DISABLE), ENABLE(ENABLE)
2~4094
UNAVAILABLE(UNAVAILABLE), AVAILABLE(AVAILABLE)
NO(NO), YES(YES)
1~254
NO(NO), YES(YES)
1000~600000
0~254
0~254
1024~65535
1024~65535
1024~65535
0~11
6~7
0~11
CLOSE, OPEN
XPU
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
30~100
ON(ON), OFF(OFF)
ON(ON), OFF(OFF)
ON(ON), OFF(OFF)
ON(ON), OFF(OFF)
1~60
None
123~65534
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
NONE(Verify None), PEER(Verify Peer Certificate)
1~30
None
1~50
None
0~19
1~124, 128~189
1~11
None
NO(NO), YES(YES)
SCUa(SCUa), SCUb(SCUb)
PARC, PARCb
0~11
1~30
None
1~50
None
ONTIME(Fixed Time), DAILY_T(Day Based Scheduling),

DAILY_C(Day Based Duration), WEEKLY_T(Week Based
Scheduling), WEEKLY_C(Week Based Duration),
MONTHLY_T(Month Based Scheduling), MONTHLY_C(Month
Based Duration)
year, month, date
year, month, date
1~100
MON_1(No.1), MON_2(No.2), MON_3(No.3), MON_4(No.4),
MON_5(No.5), MON_6(No.6), MON_7(No.7), MON_8(No.8),
MON_9(No.9), MON_10(No.10), MON_11(No.11),
MON_30(No.30), MON_31(No.31)
SUN(Sunday), MON(Monday), TUE(Tuesday),
SAT(Saturday)
hour, min
hour, min
hour, min
hour, min
hour, min
hour, min
hour, min
1~1440
hour, min
year, month, date
year, month, date
1~100
hour, min
hour, min
hour, min
hour, min
hour, min
hour, min
hour, min
1~1440
hour, min
None
None
None
None
None
0~255
None
None
0~11
0~5, 8~27
year, month, day
hour, min, sec
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~11
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
1~33
None
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
10~199
ATM(ATM), IP(IP)
PERCENTAGE(Percentage), BANDWIDTH(Band Width)
0~200000
0~200000
0~200000
0~200000
0~200000
0~200000
0~200000
0~200000
0~200000
0~200000
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
14~163
None


IP)
CBR, RT_VBR, NRT_VBR, UBR, BE, AF11, AF12, AF13,

AF21, AF22, AF23, AF31, AF32, AF33, AF41, AF42, AF43, EF,
LQBE, LQAF11, LQAF12, LQAF13, LQAF21, LQAF22,
LQAF23, LQAF31, LQAF32, LQAF33, LQAF41, LQAF42,
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF
LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL

LQAF43, LQEF

LQAF43, LQEF, NULL
LQAF43, LQEF

LQAF43, LQEF, NULL
0~11
0~5, 8~27
0~335
0~335
0~65535
GMT-1200(GMT-12:00), GMT-1100(GMT-11:00), GMT-
1000(GMT-10:00), GMT-0930(GMT-09:30), GMT-0900(GMT-
09:00), GMT-0800(GMT-08:00), GMT-0700(GMT-07:00), GMT-
04:30), GMT-0400(GMT-04:00), GMT-0330(GMT-03:30), GMT-
01:00), GMT(GMT), GMT+0100(GMT+01:00),
GMT+0200(GMT+02:00), GMT+0300(GMT+03:00),
GMT+0330(GMT+03:30), GMT+0400(GMT+04:00),
GMT+0430(GMT+04:30), GMT+0500(GMT+05:00),
GMT+0530(GMT+05:30), GMT+0545(GMT+05:45),
GMT+0600(GMT+06:00), GMT+0630(GMT+06:30),
GMT+0700(GMT+07:00), GMT+0800(GMT+08:00),
GMT+0845(GMT+08:45), GMT+0900(GMT+09:00),
GMT+0930(GMT+09:30), GMT+1000(GMT+10:00),
GMT+1030(GMT+10:30), GMT+1100(GMT+11:00),
GMT+1130(GMT+11:30), GMT+1200(GMT+12:00),
GMT+1245(GMT+12:45), GMT+1300(GMT+13:00),
GMT+1400(GMT+14:00)
NO(NO), YES(YES)
DATE(Input with date), WEEK(Input with week),
DATEWEEK(Input with date and week)
JAN(January), FEB(February), MAR(March), APR(April),
MAY(May), JUN(June), JUL(July), AUG(August),
SEP(September), OCT(October), NOV(November),
DEC(December)
1~31
FIRST(First), SECOND(Second), THIRD(Third),
FOURTH(Fourth), LAST(Last) TUE(Tuesday),
SUN(Sunday), MON(Monday),
SAT(Saturday)
hour, min, sec

DATE(Input with date), WEEK(Input with week),
DATEWEEK(Input with date and week)
JAN(January), FEB(February), MAR(March), APR(April),
MAY(May), JUN(June), JUL(July), AUG(August),
SEP(September), OCT(October), NOV(November),
DEC(December)
1~31
FIRST(First), SECOND(Second), THIRD(Third),
FOURTH(Fourth), LAST(Last) TUE(Tuesday),
SUN(Sunday), MON(Monday),
SAT(Saturday)
hour, min, sec
-120~-1, 1~120
0~4095
0~65535
0~65535
-50~50
-50~50
-58~-13
D0, D10, D20, D30, D40, D50, D60
D3, D6, D9, D12, D15, D18, D21, INFINITY
FALSE, TRUE
0~30
-24~0
FALSE(Do not send), TRUE(Send)
FALSE, TRUE
0~31

0~15
OFF(GERAN Neighboring Cell Not Support SRVCC),

ON(GERAN Neighboring Cell Support SRVCC)
OFF, ON
1~10
1~36000
6~3600
1~3600
NOPRIORITY(NOPRIORITY), GOLD(GOLD),
SILVER(SILVER), COPPER(COPPER)
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~65535
0~255
0~255
0~1
TRUE, FALSE
0~65535
-22~5
30~100
20~99
30~100
20~99
0~559
0~559
1~560
1~560
1~64000
1~4294967295
NBAMR_BITRATE_4.75K, NBAMR_BITRATE_5.15K,
NBAMR_BITRATE_10.20K, NBAMR_BITRATE_12.20K
0~559
0~559
1~560
1~560
1~64000
1~4294967295
WBAMR_BITRATE_6.60K, WBAMR_BITRATE_8.85K,
WBAMR_BITRATE_23.85K
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
ONE(One Group), TWO(Two Group), THREE(Three Group),

FOUR(Four Group)
Band1, Band2, Band3, Band4, Band5, Band6, Band7, Band8,

Band9
0~16383
0~511
0~511

Band9
0~16383
0~511
0~511

Band9
0~16383
0~511
0~511

Band9
0~16383
0~511
0~511
OFF(OFF), ON(ON)
0~7
0~7
0~7
0~7
GSM900_DCS1800_BAND_USED(Use GSM900M or 1800M
frequency band), PCS1900_BAND_USED(Use GSM1900M
frequency band)
0~1023
0~1023
0~65535
0~255
-350~150
NODEB_CREDIT_CAC_SWITCH(NodeB Credit CAC Switch)

RSVDBIT1(Reserved Switch 1), RSVDBIT2(Reserved Switch
2), RSVDBIT3(Reserved Switch 3), RSVDBIT4(Reserved
Switch 4), RSVDBIT5(Reserved Switch 5),
RSVDBIT11(Reserved Switch 11), RSVDBIT12(Reserved
Switch 15), RSVDBIT16(Reserved Switch 16)
0~4294967295
0~4294967295
SYS_LEVEL(SYS_LEVEL), NODEB_LEVEL(NODEB_LEVEL),
CELL_LEVEL(CELL_LEVEL)
OFF, ON
1~5
1~500
1~500
1~500
1~500
1~200
1~200
1~200
1~100
1~100
1~100
MBR~0
Category~1
Min~2
Max
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
MBR~0
Category~1
Min~2
Max
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~3
None
None
None
0~127
0~3
LAC(Lac), RNC(Rnc), CELL(Cell)
1~65533, 65535
0~65535
0~127
0~199
0~999
CellImmediate, PLMNNormal, SANormal, CellNormal
High, Background, Normal, Default, Butt
1~4096
0~65535
English, Italian, French, Spanish, Dutch, Swedish, Danish,

Portuguese, Finnish, Norwegian, Greek, Turkish, Hungarian,
Polish, UCS2
0~127
Earthquake, Tsunami, Hurricane, Other

None
None
None
0~65535
SAAL(SAAL Link Type ), SCTP(SCTP Link Type), SAAL-

SCTP(SAAL-SCTP Link Tpye)
0~1399
0~1199
SAAL(SAAL Link Type ), SCTP(SCTP Link Type)

ATMTODUAL(SAAL Link TO SAAL-SCTP Dual Link ),
IPTODUAL(SCTP Link TO SAAL-SCTP Dual Link),
DUALTOATM(SAAL-SCTP Dual Link TO SAAL Link),
DUALTOIP(SAAL-SCTP Dual Link TO SCTP Link )

FIXED(File of a Fixed Size), CYCLE(Periodical Generation of
New File)
5~255
0~65535
None
0~500

Band9, BandIndNotUsed
INVALID(Invalid), VALID(Valid)
0~65535
0~31
TRUE, FALSE
0~16383
0~16383
CHIP0, CHIP256, CHIP512, CHIP768, CHIP1024, CHIP1280,

CHIP1536, CHIP1792, CHIP2048, CHIP2304
1~256
1~256
0~255
0~511
TRUE, FALSE
1~8
None
0~268435455
1~65533, 65535
0~65535
NOT_REQUIRE, REQUIRE
0~255
STTD_Supported, STTD_not_Supported
CP1_Supported, CP1_not_Supported
OFFSET1, OFFSET2
None, STTD, CP1
None, STTD
None, STTD, CP1
None, STTD
None, STTD
-20~20
TRUE, FALSE
TRUE, FALSE
0~500
1~8, 255
D1, D2, D3, D4, D5, D6, D7, D8
0~65535
0~65535
0~65535
0~65535
0~65535
0~65535
0~65535
0~65535
TRUE, FALSE
0~3
0~65535
-100~500
-100~500
-350~150
-350~150
-350~150
-350~150
0~65535
None
None
None
0~268435455
FALSE(CellNotSyn), TRUE(CellSyn)
-100~500
-100~500
-100~500
-350~150
-350~150
-350~150
-350~150
-10~5
0~65535
RESERVED, NOT_RESERVED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
BARRED, NOT_BARRED
ALLOWED, NOT_ALLOWED
D10, D20, D40, D80, D160, D320, D640, D1280

BARRED, NOT_BARRED
ALLOWED, NOT_ALLOWED
D10(10 seconds), D20(20 seconds), D40(40 seconds), D80(80

seconds), D160(160 seconds), D320(320 seconds), D640(640
seconds), D1280(1280 seconds)
0~65535
1~65533, 65535
0~65535
NOT_REQUIRE, REQUIRE
0~255
0~65535
CRD_ADCTRL(Credit Admission Control Algorithm),
HSDPA_UU_ADCTRL(HSDPA UU Load Admission Control
Algorithm), HSUPA_UU_ADCTRL(HSUPA UU Load Admission
Control Algorithm), MBMS_UU_ADCTRL(MBMS UU Load
Admission Control Algorithm), HSDPA_GBP_MEAS(HSDPA
GBP Meas Algorithm), HSDPA_PBR_MEAS(HSDPA PBR
Meas Algorithm), HSUPA_PBR_MEAS(HSUPA PBR Meas
Algorithm), HSUPA_EDCH_RSEPS_MEAS(HSUPA EDCH
RSEPS Meas Algorithm), EMC_UU_ADCTRL(emergency call
power admission), RTWP_RESIST_DISTURB(RTWP Resist
Disturb Switch), FACH_UU_ADCTRL(FACH power cac switch),
MIMOCELL_LEGACYHSDPA_ADCTRL(Legacy HSDPA
Admission Control Algorithm in MIMO Cell ),
FAST_DORMANCY_ADCTRL(Fast Dormancy User Admission
Control Algorithm)
ALGORITHM_OFF, ALGORITHM_FIRST,
ALGORITHM_SECOND, ALGORITHM_THIRD
ALGORITHM_SECOND, ALGORITHM_THIRD
INTRA_FREQUENCY_LDB(Intra Frequency LDB Algorithm),

PUC(Potential User Control Algorithm), UL_UU_LDR(Uplink
UU LDR Algorithm), DL_UU_LDR(Downlink UU LDR
Algorithm), UL_UU_OLC(Uplink UU OLC Algorithm),
DL_UU_OLC(Downlink UU OLC Algorithm),
OLC_EVENTMEAS(OLC Event Meas Algorithm),
CELL_CODE_LDR(Code LDR Algorithm),
CELL_CREDIT_LDR(Credit LDR Algorithm),
UL_INTRA_FREQUENCY_ULB(Intra Frequency ULB
Algorithm)
ALGORITHM_REQUIRED, ALGORITHM_DEPEND_ON_LCG
64QAM(Cell 64QAM Function Switch), MIMO(Cell MIMO
Function Switch), E_FACH(Cell E_FACH Function Switch),
DTX_DRX(Cell DTX_DRX Function Switch),
HS_SCCH_LESS_OPERATION(Cell HS_SCCH LESS
OPERATION Function Switch), DL_L2ENHANCED(Cell DL
L2ENHANCED Function Switch), 64QAM_MIMO(Cell
64QAM+MIMO Function Switch), UL_16QAM(Cell UL 16QAM
Function Switch), DC_HSDPA(Cell DC-HSDPA Function
Switch), UL_L2ENHANCED(Cell UL L2ENHANCED Function
Switch), EDPCCH_BOOSTING(Cell E-DPCCH Boosting
Function Switch), DCMIMO_HSDPA(Cell DC-HSDPA
Combined with MIMO Function Switch), E_DRX(Enhanced
Discontinous Reception Function Switch)
E_F_DPCH_OFF, E_F_DPCH_ON
TX_DIVERSITY_ON_TO_OFF(TX diversity capability is on to

off), TX_DIVERSITY_OFF_TO_ON(TX diversity capability is off
to on)
NBM_LDC_ALL_UE(Select all users),
NBM_LDC_MATCH_UE_ONLY(Select users match target cell
support only), NBM_LDC_MATCH_UE_FIRST(Select users
match target cell support first)
0~4294967295
0~4294967295
OFF(Offload Function is OFF), ON(Offload Function is ON)
OFF(Algorithm is OFF), ON(Algorithm is ON)

0~65535
0~65535
0~65535
TU, RA, HT
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
1~200
1~200
0~100
0~100
0~100
0~100
0~100
0~100
0~128
-50~33
-50~33
-50~33
-50~33
0~621
-30~30
OFF, ON
1~6000
0~10
0~128
0~100
0~100
0~100
0~63
0~100
0~63
SF4(SF4), SF8(SF8), SF16(SF16), SF32(SF32), SF64(SF64),

SF128(SF128), SF256(SF256), SFOFF(SFOFF)

SF128(SF128), SF256(SF256), SFOFF(SFOFF)
hour, min, sec
hour, min, sec
1~100
1~400
0~48
0~100
0~48
0~100
0~100
0~100
0~65535
0~65535
0~3
0~65535
OFF(Message is invalid), ON(Message is valid)
None
0~65535
WALKING_SPEED_AND_HOT_SPOT_CELL,
MID_SPEED_AND_HOT_SPOT_CELL,
HIGH_SPEED_AND_HOT_SPOT_CELL,
LOW_SPEED_AND_MEDIUM_COVERAGE_CELL,
HIGH_SPEED_AND_MEDIUM_COVERAGE_CELL,
LOW_SPEED_AND_HIGH_COVERAGE_CELL,
HIGH_SPEED_AND_HIGH_COVERAGE_CELL,
OTHER_CELL
D8, D16, D32, D64, D128, D256
D8, D16, D32, D64, D128, D256
0~65535
0~100
0~100
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
0~65535
OFF, ON
0~255
0~100
0~100
0~65535
0~5
ON, OFF
ON, OFF
ON, OFF
Power, UserNumber
0~100
0~100
ON, OFF
SF4, SF8, SF16, SF32, SF64, SF128, SF256
0~100

Band9, DependOnNCell, BandIndNotUsed
TRUE, FALSE
0~16383
0~16383
ON, OFF
0~100
ON, OFF
0~65535
ON, OFF
ON, OFF
0~30
0~30
0~30
0~30
0~30
0~30
0~30
0~30
0~65535
0~3
FALSE, TRUE
FALSE, TRUE
RestrictionFixed, RestrictionFlexible
AC0(Access Class 0 Restriction), AC1(Access Class 1
Restriction), AC2(Access Class 2 Restriction), AC3(Access
Class 3 Restriction), AC4(Access Class 4 Restriction),
AC15(Access Class 15 Restriction)
1~16

6~3600
0~65535
OFF(switch off), ON_1(switch on1), ON_2(switch on2),

ON_3(switch on3)
hour, min
hour, min
hour, min
hour, min
hour, min
hour, min
FORCESHUTDOWN(ForceShutDown),
CONDITIONALSHUTDOWN(ConditionalShutDown),
QOSSHUTDOWN(QosShutDown)
0~15
0~15
0~15
0~100
SPI1(SPI1), SPI2(SPI2), SPI3(SPI3), SPI4(SPI4), SPI5(SPI5),
SPI6(SPI6), SPI7(SPI7), SPI8(SPI8), SPI9(SPI9),
SPI10(SPI10), SPI11(SPI11), SPI12(SPI12), SPI13(SPI13),
SPI14(SPI14), SPI15(SPI15)
0~65535
EDRXT321_100(T321 timer length is 100ms),
EDRXT321_800(T321 timer length is 800ms)
EDRXCYCLE_4(DRX Cycle is 4 frame), EDRXCYCLE_8(DRX
Cycle is 8 frame), EDRXCYCLE_16(DRX Cycle is 16 frame),
EDRXCYCLE_32(DRX Cycle is 32 frame)
EDRXBURST_1(Rx Burst is 1 frame), EDRXBURST_2(Rx
Burst is 2 frame), EDRXBURST_4(Rx Burst is 4 frame),
EDRXBURST_8(Rx Burst is 8 frame), EDRXBURST_16(Rx
Burst is 16 frame)
INTERRUPTION_CFG(Interruption mode),
INTERRUPTION_NOT_CFG(Noninterruption mode)
0~65535
-350~150
-350~150
-350~150
1~1000
1~2000
1~1000
1~2000
1~1000
1~2000
1~1000
1~2000
1~1000
1~2000
1~1000
1~2000
1~1000
1~2000
0~65535
1~32
1~32
-350~150
-350~150
1~5
0~1279
0~2559
1~2000
0~65535
D8, D16
D8, D16
FALSE, TRUE
0~49
0~65535
TRUE, FALSE
1~15
0~4095
0~65535

TRUE, FALSE
0~16383
0~16383
0~65535
INACTIVE, ACTIVE
0~65535
USED, NOT_USED
0~7
-53~45
-53~45
0~99
NOT_USED, D30(30 seconds), D60(60 seconds), D120(120
seconds), D180(180 seconds), D240(240 seconds)
1~16
NOT_USED, D10(10 seconds), D20(20 seconds), D30(30
-16~10
0~65535
OFF, ON
0~511
1~16
0~255
0~511
1~16
0~120
0~65535
INTERFREQ(inter-frequency handover only), INTERRAT(inter-

RAT handover only), SIMINTERFREQRAT(inter-frequency and
inter-RAT handover)
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters),
COEXIST_MEAS_THD_CHOICE_INTERRAT(Choosing the
inter-RAT oriented parameters)
OFF, ON
OFF, ON
0~65535
Manual(Manual), Automatic(Automatic)
1~15
1~15
1~15
1~15
-500~0
Minus3.0DB(-3.0dB), Minus2.5DB(-2.5dB), Minus2.0DB(-
2.0dB), Minus1.5DB(-1.5dB), Minus1.0DB(-1.0dB),
Minus0.5DB(-0.5dB), 0.0DB(0.0dB), 0.5DB(0.5dB),
1.0DB(1.0dB), 1.5DB(1.5dB), 2.0DB(2.0dB), 2.5DB(2.5dB),
9.0DB(9.0dB), 9.5DB(9.5dB), 10.0DB(10.0dB),
10.5DB(10.5dB), 11.0DB(11.0dB), 11.5DB(11.5dB),
12.0DB(12.0dB), 12.5DB(12.5dB), 13.0DB(13.0dB),
13.5DB(13.5dB), 14.0DB(14.0dB), 14.5DB(14.5dB),
15.0DB(15.0dB), 15.5DB(15.5dB), 16.0DB(16.0dB),
16.5DB(16.5dB), 17.0DB(17.0dB), 17.5DB(17.5dB),
18.0DB(18.0dB), 18.5DB(18.5dB), 19.0DB(19.0dB)
Mode0, Mode1
OFF(OFF), ON(ON)
1~16
0~300
Minus3.0DB(-3.0dB), Minus2.5DB(-2.5dB), Minus2.0DB(-

2.0dB), Minus1.5DB(-1.5dB), Minus1.0DB(-1.0dB),
Minus0.5DB(-0.5dB), 0.0DB(0.0dB), 0.5DB(0.5dB),
9.0DB(9.0dB), 9.5DB(9.5dB), 10.0DB(10.0dB),
10.5DB(10.5dB), 11.0DB(11.0dB), 11.5DB(11.5dB),
12.0DB(12.0dB), 12.5DB(12.5dB), 13.0DB(13.0dB),
13.5DB(13.5dB), 14.0DB(14.0dB), 14.5DB(14.5dB),
15.0DB(15.0dB), 15.5DB(15.5dB), 16.0DB(16.0dB),
16.5DB(16.5dB), 17.0DB(17.0dB), 17.5DB(17.5dB),
18.0DB(18.0dB), 18.5DB(18.5dB), 19.0DB(19.0dB)
0~65535
0~65535
PO_5/15, PO_6/15, PO_8/15, PO_9/15, PO_12/15, PO_15/15,

PO_19/15, PO_24/15, PO_30/15
PO_5/15, PO_6/15, PO_8/15, PO_9/15, PO_12/15, PO_15/15,
PO_19/15, PO_24/15, PO_30/15
1~4
1~4
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D4, D8, D10, D20, D40, D80, D160
0~65535
1~8
1~8
0~100
0~100
0~4095
0~65535
0~65535
0~65535
PERIODICAL_REPORTING(Periodical reporting),
EVENT_TRIGGER(Event trigger)
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
NON_PERIODIC_REPORT(Non periodical reporting),

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~29
0~29
0~29
0~29
0~20
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~64000
-24~0
-24~0
-24~0
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
0~512
1~64
0~63
0~1000
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~29
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
-24~0
0~512
1~64
0~63
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
CPICH_EC/NO, CPICH_RSCP, AUTO
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~20

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~29
0~29
0~15
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~64000, 65535
0~64000
REQUIRED(Verify mode), NOT_REQUIRE(Non-verify mode)
-24~0
-24~0
-24~0
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
0~63
0~63
0~63
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
0~512
0~65535
0~15
1~64
0~63
0~63
0~65535
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~63
0~63
1~16
0~512
0~100
0~100
1~64
0~63
0~63
0~65535
0~4095
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
CPICH_EC/NO, CPICH_RSCP
NON_PERIODIC_REPORT, D250, D500, D1000, D2000,

D4000, D8000, D16000

D4000, D8000, D16000

D4000, D8000, D16000
0~29
0~29
0~29
0~29
0~29
0~29
-24~0
-115~-25
0~15
0~15
0~15
0~15
0~15
0~15
0~20
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
-24~0
1~6
-115~-25
0~65535
0~100
0~100
0~100
0~65535
0~100
0~100
0~100
0~100
0~100
0~100
0~100
0~100
10~600000
0~100
0~100
0~100
0~100
0~300
0~65535
NoAct(no action), InterFreqLDHO(inter-freq load handover),
BERateRed(BE traff rate reduction), QoSRenego(uncontrolled
real-time traff Qos re-negotiation),
CSInterRatShouldBeLDHO(CS domain inter-rat should be load
handover), PSInterRatShouldBeLDHO(PS domain inter-rat
should be load handover), AMRRateRed(AMR traff rate
reduction), MBMSDecPower(MBMS descend power),
CodeAdj(Code adjust), CSInterRatShouldNotLDHO(CS domain
inter-rat should not be load handover),
PSInterRatShouldNotLDHO(PS domain inter-rat should not be
load handover)

load handover)

load handover)

load handover)
load handover)

load handover)

load handover)

load handover)
load handover)

load handover)
1~10
1~10
1~10
1~10
1~10
1~10
1~10

reduction), CSInterRatShouldNotLDHO(CS domain inter-rat
should not be load handover), PSInterRatShouldNotLDHO(PS
domain inter-rat should not be load handover)





1~10
1~10
1~10
1~10
1~10
1~10
1~10
0~100
0~100
0~400000
0~400000
1~15

SF128(SF128), SF256(SF256)
FALSE(FALSE), TRUE(TRUE)
1~3

SF128(SF128), SF256(SF256)

SF128(SF128), SF256(SF256)
0~100
OFF(OFF), ON(ON)
R99_CONVERSATIONAL(R99 Conversational),
R99_STREAMING(R99 Streaming), R99_BE(R99 BE),
HSDPA_CONVERSATIONAL(HSDPA Conversational),
HSDPA_STREAMING(HSDPA Streaming),
HSDPA_BE(HSDPA BE), HSPA_CONVERSATIONAL(HSPA
Conversational), HSPA_STREAMING(HSPA Streaming),
HSPA_BE(HSPA BE)
8SF4(8SF4), 7SF4(7SF4), 6SF4(6SF4), 5SF4(5SF4),
4SF4(4SF4), 3SF4(3SF4), 2SF4(2SF4), SF4(SF4), SF8(SF8),
SF16(SF16), SF32(SF32), SF64(SF64), SF128(SF128),
SF256(SF256)
BLINDHO(BLINDHO), MEASUREHO(MEASUREHO)
0~65535
INTELLIGENT_INTERFREQ_UE_TYPE_STEERING
0~65535
CSAMR_INTERFREQ(CS AMR inter-frequency switch),

CSNONAMR_INTERFREQ(CS non AMR inter-frequency
switch), PSR99_INTERFREQ(PSR99 inter-frequency switch),
PSHSPA_INTERFREQ(PSHSPA inter-frequency switch)
0~100
0~100
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
CPICH_EC/NO, CPICH_RSCP, BOTH

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~64000
0~29
0~29
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
-24~0
-115~-25
0~3
0~512
0~65535
CSAMR_INTERRAT(CS AMR inter-RAT switch)
0~100
0~100
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~64000, 65535
0~64000
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~63
0~3
ALL_USER(All User), HALF(Half), THIRD(THIRD),
QUARTER(QUARTER)
0~512
0~300
0~65535
STREAMING, BACKGROUND
D16, D32, D64, D128, D256
-350~150
0~100
0~100
0~1279
0~2559
0~65535
PTM, PTP, ENHANCEDPTM, DYNAMIC

2~10
1~5
0~65535
0~3
0~65535
0~65535
D16, D32, D64, D128, D256
TRUE, FALSE
0~65535
0~255
-10~5
FALSE(Not Use), TRUE(Use)
1~255
1~32
OFF(OFF), ON(ON)
0~65535
OFF, ON
1~255
D250, D500, D1000, D2000, D3000, D4000, D6000, D8000,

D12000, D16000, D20000, D24000, D28000, D32000, D64000
-115~-25
-24~0
1~65535
0~65535
1~255
D250, D500, D1000, D2000, D3000, D4000, D6000, D8000,

D12000, D16000, D20000, D24000, D28000, D32000, D64000
-115~-25
-24~0
0~65535
REQUIRE, NOT_REQUIRE
NOT_REQUIRE, INTER_FREQ, INTER_RAT,

INTER_FREQ_AND_INTER_RAT
REQUIRE, NOT_REQUIRE, INTER_FREQ, INTER_RAT,
INTER_FREQ_AND_INTER_RAT
0~4095
0~65535
None
0~65535
0~255
0~65535
0~65535
0~7
0~31
0~31
D6(D6), D15(D15), D25(D25), D50(D50), D75(D75),

D100(D100)
-70~-22
D0(D0), D1(D1), D2(D2), D3(D3), D4(D4), D5(D5), D6(D6),

D7(D7), D8(D8), D9(D9), D10(D10), D11(D11), D12(D12),
D13(D13), D14(D14), D15(D15), D16(D16)
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
1~504
0~65535
0~100
0~100
1~10
1~10
1~99
100~200
1~65535
1~65535
0~10
0~10
MBMS_REL(MBMS service), USER_REL(UE)
0~8
0~10
0~30
0~65535
0~100
0~100
0~100
-10~10
-10~10
-20~20
-20~20
-20~20
-20~20
0~65535
-15~15
0~512
0~512
0~65535
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
0~65535
AMR, VP, PSR99, PSHSPA
OFF, ONLY_TO_INTER_FREQUENCY,
ONLY_TO_INTER_RAT
0~100
0~100

FALSE, TRUE
0~16383
0~16383
0~65535
0~65535
0~65535
CS_DOMAIN, PS_DOMAIN
0~16000000
-350~150
-350~150
D4(SF4), D8(SF8), D16(SF16), D32(SF32), D64(SF64),
D128(SF128), D256(SF256), D512(SF512)
0~65535
CPICH_ECNO(CPICH Ec/N0), CPICH_RSCP(CPICH RSCP)
0~20
0~20
0~20, 255
0~20, 255
0~31
-24~0
-58~-13
TRUE, FALSE
-2~-1
-50~33
-16~10, 127
-16~10, 127
-16~10, 127
-16~10, 127
-16~10, 127
0~10, 255
4~19, 255
4~19, 255
CONFIGURED, NOT_CONFIGURED
NotUsed, D30(30 seconds), D60(60 seconds), D120(120
seconds), D180(180 seconds), D240(240 seconds)
1~16
NotUsed, D10(10 seconds), D20(20 seconds), D30(30
0~40, 255
0~40, 255
0~40, 255
0~40, 255
0~31, 255
0~31, 255
0~7
0~31
0~7
0~31
0~65535
SIB2, SIB4, SIB12, SIB18, SIB19, SIB11BIS
0~65535
MeasurementQuantity(MeasurementQuantity), Both(Both)
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~512
RSRP(Reference Signal Receiving Power), RSRQ(Reference

Signal Receiving Quality)
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
1~97
1~34
0~65535
0~100
0~100
0~100
0~65535
0~65535
0~3
20~65535
1~10
1~1440
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~65535
-10~5
-22~5
ABNORMAL_ONLY, NORMAL_ONLY
CS_ONLY, PS_ONLY
CONN_SETUP, RAB, DCCC, SHO, HHO, SYS_HO_OUT,

RRC_RELEASE, STAT, NET_OPT
ORIGINATING_CONVERSATIONAL_CALL,
ORIGINATING_STREAMING_CALL,
ORIGINATING_INTERACTIVE_CALL,
ORIGINATING_BACKGROUND_CALL,
ORIGINATING_SUBSCRIBED_TRAFFIC_CALL,
TERMNT_CONVERSATIONAL_CALL,
TERMNT_STREAMING_CALL,
TERMNT_INTERACTIVE_CALL,
TERMNT_BACKGROUND_CALL, EMERGENCY_CALL,
INTER_RAT_CELL_RESELECTION,
INTER_RAT_CELL_CHG_ORDER, REGISTRATION,
DETACH, ORIGINATING_HIGH_PRIOR_SIG,
ORIGINATING_LOW_PRIOR_SIG, CALL_RE_ESTAB,
TERMNT_HIGH_PRIOR_SIG, TERMNT_LOW_PRIOR_SIG,
TERMNT_CAUSE_UNKNOWN, MBMS_RECEPTION,
MBMS_PTP_RB_REQ
ByRack, ByNodeBId, ByCellId
0~11
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~7
0~65535
0~65535
OFF, ON
OFF, ON
1~31
0~255
D8, D16, D32, D64, D128, D256
D8, D16, D32, D64, D128, D256
HIGH_SPEED_AND_HIGH_COVERAGE_CELL,
OTHER_CELL
FALSE(Not Limited), TRUE(Limited)
D8, D16, D32, D64, D128, D256

FALSE(Forbidden), TRUE(Permit)
Limited, Permit, BasedOnUECap(Based On UE Capability)
FALSE(Forbidden), TRUE(Permit)
0~255
NOT_ALLOWED, ALLOWED
MODE1, MODE2
6~9
0~3
0~4095
0~186
R99, R4, R5, R6, R7, R8
CR527_SUPPORT, CR527_NOT_SUPPORT,
CR529_SUPPORT, CR529_NOT_SUPPORT
NORMAL, OFFLOAD, INHIBITED
0~65535
ATM_TRANS, IP_TRANS
OFF, ON
1~5
OFF, ON
RSVDBIT1_BIT1, RSVDBIT1_BIT2, RSVDBIT1_BIT3,

RSVDBIT1_BIT31, RSVDBIT1_BIT32
0~4294967295
OFF, ON
0~4294967295
0~3
PsBlk(BLOCK PS), CsAndPsBlk(BLOCK CS AND PS)

2~30
PRIM(Primary Operator), SEC(Secondary Operator),

OUTER(Outer Operator), COMM(Common Operator)
None
None
None
0~3, 5~31
0~3
0~3, 5~31
0~31
None
ONE(One), TWO(Two), THREE(Three), FOUR(Four)
0~3, 5~31
0~3, 5~31
0~3, 5~31
0~3, 5~31
5~31, 255
ON, OFF
1024~4294967295
0~65535
0~180
0~999
1~65535
0~100
D100, D200, D400, D600, D800, D1000, D1200, D1400,

D1600, D1800, D2000, D3000, D4000, D6000, D8000
0~7
D100, D200, D400, D1000, D2000
0~7
INFINITY, D5, D10, D30, D60, D120, D360, D720
D5, D10, D15, D20, D30, D40, D50
D40, D80, D160, D320
1~8
1~8
1~15
D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800,
D1000
0~15
D1, D2, D4, D10, D20, D50, D100, D200

D0, D2, D4, D6, D8, D12, D16, D20
D0, D10, D30, D60, D180, D600, D1200, D1800
D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800,
D1000
D0, D10, D20, D30, D40, D50, INFINITY
D0, D100, D200, D300, D400, D500, D600, D700, D800, D900,
D1000, D1200, D1500, D2000
D1, D2, D3, D4
D0, D5, D10, D20, D30, D60, D90, D120, INVALID
CFG_DL_BLIND_DETECTION_SWITCH,
CFG_HSDPA_64QAM_SWITCH, CFG_HSDPA_DC_SWITCH,
CFG_HSDPA_MIMO_SWITCH,
CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,
CFG_HSPA_DTX_DRX_SWITCH,
CFG_HSPA_HSSCCH_LESS_OP_SWITCH,
CFG_HSUPA_16QAM_SWITCH,
CFG_IMS_SUPPORT_SWITCH,
CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH,
CFG_LOSSLESS_RELOC_CFG_SWITCH,
CFG_MULTI_RAB_SWITCH,
CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,
CFG_PDCP_RFC2507_HC_SWITCH,
CFG_PDCP_RFC3095_HC_SWITCH, CFG_PTT_SWITCH,
CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,
CFG_EDPCCH_BOOSTING_SWITCH,
CFG_HSDPA_DCMIMO_SWITCH,
CFG_FREE_USER_SWITCH,
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH
DRA_AQM_SWITCH,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH,
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH,
DRA_DCCC_SWITCH,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_DCCC_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH,
DRA_IP_SERVICE_QOS_SWITCH,
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_PS_NON_BE_STATE_TRANS_SWITCH,
DRA_R99_DL_FLOW_CONTROL_SWITCH,
DRA_THROUGHPUT_DCCC_SWITCH,
DRA_VOICE_SAVE_CE_SWITCH,
DRA_VOICE_TTI_RECFG_SWITCH
CS_AMRC_SWITCH,
CS_HANDOVER_TO_UTRAN_DEFAULT_CFG_SWITCH,
CS_IUUP_V2_SUPPORT_SWITCH
PC_CFG_ED_POWER_INTERPOLATION_SWITCH,
PC_DL_INNER_LOOP_PC_ACTIVE_SWITCH,
PC_DOWNLINK_POWER_BALANCE_SWITCH,
PC_EFACH_ECN0_DYN_ADJ_SWITCH,
PC_FP_MULTI_RLS_IND_SWITCH,
PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH,
PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH,
PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITCH,
PC_INNER_LOOP_LMTED_PWR_INC_SWITCH,
PC_OLPC_SWITCH,
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH,
PC_SIG_DCH_OLPC_SWITCH,
PC_UL_SIRERR_HIGH_REL_UE_SWITCH
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_RAB_5_CFG_ROHC_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH
MAP_HSUPA_TTI_2MS_SWITCH,
MAP_INTER_RAT_PS_IN_CHANLE_LIMIT_SWITCH,
MAP_PS_BE_ON_E_FACH_SWITCH,
MAP_PS_STREAM_ON_E_FACH_SWITCH,
MAP_PS_STREAM_ON_HSDPA_SWITCH,
MAP_PS_STREAM_ON_HSUPA_SWITCH,
MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH,
MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH
DR_RRC_DRD_SWITCH, DR_RAB_SING_DRD_SWITCH,
DR_RAB_COMB_DRD_SWITCH,
DR_INTER_RAT_DRD_SWITCH
HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,
HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH
SRNSR_DSCR_IUR_RESRCE_SWITCH,
SRNSR_DSCR_LOC_SEPRAT_SWITCH,
SRNSR_DSCR_PROPG_DELAY_SWITCH,
SRNSR_DSCR_SEPRAT_DUR_SWITCH
CMCF_DL_HLS_SWITCH, CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH
RESERVED_SWITCH_0_BIT1,
RESERVED_SWITCH_0_BIT32
0~4294967295
0~4294967295
0~255
0~255
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH, CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,
CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH
PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~255
0~255
0~255
0~255
40~100
0~65535
1~32
RAN_CTRLPLN_FC(RAN Flow Control Switch)
50~200
0~100
0~100
0~100
0~100
0~100
1~10
0~255
0~255
0~255
0~3
1~65533, 65535
0~65535
0~4799
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384

D0, D8, D16, D32, D64, D128, D144, D256, D384
RATE_UP_AND_DOWN_ON_DCH,
RATE_UP_ONLY_ON_DCH
RATE_UP_AND_DOWN_ON_EDCH,
RATE_UP_ONLY_ON_EDCH
0~100
0~100
2_Rates, 3_Rates
2_Rates, 3_Rates
AUTO_CALC, HAND_APPOINT
D16, D32, D64, D128, D144, D256, D384
2_Rates, 3_Rates
2_Rates, 3_Rates
AUTO_CALC, HAND_APPOINT
D16, D32, D64, D128, D144, D256, D384
1~255
1~65535
1~65535
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
1~1000
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720, D5440, D11480
0~1148
0~49
MultiIMSI, SingleIMSI
None
None
None
None
1~8
0~7
0~7
0~7
OFF, ON
0~255
0~100
0~100
1~255
1~65535
1~65535
1~65535
1~65535
OFF(OFF), ON(ON)
1~1000
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~100
0~100
OFF(OFF), ON(ON)
0~1000
0~100
0~100
0~100
TPE_DOWNLINK_SWITCH, TPE_UPLINK_SWITCH
1~255
1~100
0~100
1~10
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
Qos(Enable the counters of QoS), Spi(Enable the counters of
SPI), QosAndSpi(Enable the counters of QoS and SPI),
BothOFF(Disable the counters of QoS and SPI)
0~65535
0~65535
1~100
1~100
1~100
0~3600
0~3600
1~200
0~200
0~200
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~100
RsvdSwitch1_Bit1, RsvdSwitch1_Bit2, RsvdSwitch1_Bit3,
RsvdSwitch1_Bit31, RsvdSwitch1_Bit32
RsvdSwitch2_Bit31, RsvdSwitch2_Bit32
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~5
ON, OFF
ON, OFF
ON, OFF
UserNumber, Power
OFF, Only_To_Inter_Frequency, Allowed_To_Inter_RAT
0~100
0~100
0~100
0~100
0~100
ON, OFF
0~100
SF4, SF8, SF16, SF32, SF64, SF128, SF256

0~100

TRUE, FALSE
0~16383
0~16383
ON, OFF
0~100
0~100
OFF, ON
ON, OFF
ON, OFF
ON, OFF
0~30
0~30
0~30
0~30
0~30
0~30
0~30
0~30
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
OFF, ON
FALSE, TRUE
FALSE, TRUE
1~16
1~36000
6~3600
0~255
0~255
0~255
0~100
0~255
CONVERSATIONAL, STREAMING, INTERACTIVE,

BACKGROUND, NBAMR, WBAMR
EDCH_10MS, EDCH_2MS
ON, OFF
D1, D4, D8, D16, D32, D64, D128, D256
D2, D4, D15
D1, D2, D4, D8, D16, D32, D64, D128, D256, D512, INFINITY
D0, D1, D2, D4, D8, D16, D32, D64, D128, D256, D512,
INFINITY
D1, D2, D5
D1, D2, D5
ON, OFF
D4, D5, D8, D10, D16, D20
D0, D1, D2, D4, D8, D16, D32, D64, D128, D256, D512
D0, D1, D2, D4, D8, D16, D32, D64, D128, D256
TRUE, FALSE
D0, D2, D4, D8, D10, D20, D40, D80, D160, D16, D32, D64
D1, D4, D5, D8, D10, D16, D20
D4, D5, D8, D10, D16, D20, D32, D40, D64, D80, D128, D160
D1, D4, D5, D8, D10, D16, D20
Low(Low), Middle(Middle), High(High)







RATE_8KBPS, RATE_16KBPS, RATE_32KBPS,
RATE_5440KBPS, RATE_11480KBPS
OFF, ON
Gold, Silver, Copper
0~1000
0~82
0~82
0~1000
0~82
0~82
0~1000
0~82
0~82
0~82
0~82
0~82
0~82
0~100
0~100
0~100
0~100
RTWP~0
IUB~1
CE
0~65535
0~65535
0~15
0~15
0~15
D0.9, D0.8, D0.7, D0.6, D0.5, D0.4, D0.3, D0.2
0~65535
TTI_2MS, TTI_10MS
SIGNATURE0, SIGNATURE1, SIGNATURE2, SIGNATURE3,
SIGNATURE8, SIGNATURE9, SIGNATURE10,
SIGNATURE14, SIGNATURE15
SUBCHANEL0, SUBCHANEL1, SUBCHANEL2,

SUBCHANEL9, SUBCHANEL10, SUBCHANEL11
-35~-10
1~64
1~8
1~32
0~50
0~50
0~32
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720, D5440
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720, D5440
0~5000
0~65535
None
0~32
OFF, ON
None
None
0~31
1~65533, 65535
NOT_REQUIRE(Not configure RAC information),
REQUIRE(Configure RAC information)
0~255
0~65535
0~7
0~7
0~1023
GSM900_DCS1800_BAND_USED(Use GSM900M or 1800M
frequency band), PCS1900_BAND_USED(Use GSM1900M
frequency band)
NO_CAPABILITY(Cell capability unknown), GSM(GSM),

GPRS(GPRS), EDGE(EDGE)
USED(HCS cell), NOT_USED(Non HCS cell)
0~7
0~99
NC0, NC1, NC2, RESET
FALSE, TRUE
FALSE, TRUE
-50~50
0~4095
0~65535
SINGLE_HOST, DOUBLE_HOST,
DOUBLE_HOST_OUT_POOL
None
0~31
0~511

TRUE, FALSE
0~16383
0~16383
0~4095
0~65535
TRUE, FALSE
1~65533, 65535
NOT_REQUIRE(Not configure RAC information),
REQUIRE(Configure RAC information)
0~255
TRUE(Configure the minimum quality threshold), FALSE(Not
configure the minimum quality threshold)
-24~0
TRUE(Configure the minimum signal level for access),
FALSE(Not configure the minimum signal level for access)
-58~-13
TRUE, FALSE
-2~-1
TRUE(Configure the maximum uplink power of UE),
FALSE(Not configure the maximum uplink power of UE)
-50~33
USED(HCS cell), NOT_USED(Non HCS cell)
0~7
0~99
FALSE, TRUE
STTD_Supported, STTD_not_Supported
CP1_Supported, CP1_not_Supported
OFFSET1, OFFSET2
None, STTD, CP1
None, STTD
None, STTD, CP1
None, STTD
None, STTD
DELAY_ACTIVATION_SUPPORT(delay activation support
indication), HSDSCH_SUPPORT(HSDSCH support indication),
FDPCH_SUPPORT(F-DPCH support indication),
EDCH_SUPPORT(E-DCH support indication),
EDCH_2MS_TTI_SUPPORT(E-DCH 2ms TTI support
indicator), EDCH_2SF2_AND_2SF4_SUPPORT(E-DCH max
SF support 2SF2+2SF4 indicator), EDCH_2SF2_SUPPORT(E-
DCH max SF support 2SF2 indicator),
EDCH_2SF4_SUPPORT(E-DCH max SF support 2SF4
indicator), EDCH_SF4_SUPPORT(E-DCH max SF support SF4
indicator), EDCH_SF8_SUPPORT(E-DCH max SF support SF8
indicator), EDCH_HARQ_IR_COMBIN_SUPPORT(E-DCH
support HARQ IR Combining indicator),
EDCH_HARQ_CHASE_COMBIN_SUPPORT(E-DCH support
HARQ CHASE Combining indicator),
CPC_DTX_DRX_SUPPORT(CPC DTX-DRX support indicator),
CPC_HS_SCCH_LESS_OPER_SUPPORT(CPC HS-SCCH
less operation support indicator),
HSPAPLUS_MIMO_SUPPORT(MIMO support indicator),
FLEX_MACD_PDU_SIZE_SUPPORT(flexible MAC-d PDU
Size support indicator),
FDPCH_SLOT_FORMAT_SUPPORT(F-DPCH slot format
support indicator),
HSPAPLUS_DL_64QAM_SUPPORT(downlink 64QAM support
indicator)
FORBIDDEN, NOT_FORBIDDEN
Mode0, Mode1
-20~20
TRUE, FALSE
TRUE, FALSE
TRUE, FALSE
0~65535
0~255
1~32
1~256
0~1279
0~2559
-350~150
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13,
D14, D15
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13,
D14, D15
FALSE, TRUE
NO_CODING, CONVOLUTIONAL, TURBO
D1/2, D1/3
BACKGROUND
GOLD, SILVER, COPPER
1~1000
0~65535
1~32
0~4992
D1, D2, D3
0~512
0~512
0~512
0~65535
1~32
0~24
-350~150
-350~150
-35~-10
ALGORITHM1, ALGORITHM2
1~2
STEPSIZE_0.5DB, STEPSIZE_1DB, STEPSIZE_1.5DB,
STEPSIZE_2DB
SINGLE_TPC, TPC_TRIPLET_IN_SOFT,
TPC_AUTO_ADJUST
ON, OFF
10~25
3~9
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384
SCHEDULED, NON-SCHEDULED
D10, D20, D50, D100, D200, D500, D1000

D2, D10, D20, D50, D100, D200, D500, D1000
D10, D20, D50, D100, D200, D500, D1000
D2, D10, D20, D50, D100, D200, D500, D1000
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720, D5440
D8, D16, D32, D64, D128, D144, D256, D384
OFF, ON
D32, D64
EDCH_TTI_10ms, EDCH_TTI_2ms
D8, D16, D32, D64, D128, D144, D256, D384, D608
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720
0~49
0~65535
4~1504
4~402
4~402
4~1504
MIMO, 64QAM
D0, D1, D2, D4, D8, D16, D32, D64, D128

SRB_OVER_HSDPA, SRB_OVER_HSUPA, TTI_2MS, MIMO,
64QAM, DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA
SLOT_FORMAT_1, SLOT_FORMAT_4
-100~100
-100~100
MIMO_64QAM, DC_HSDPA
0~11480
1~15
NOT_TRIGGER, TRIGGER
NOT_PRE_EMPTABLE, PRE_EMPTABLE
NOT_ALLOWED, ALLOWED
3~9
1~100
0~1504
4~402
4~402
1~100
1~100
DCH(UL_DCH,DL_DCH), HSPA(UL_EDCH,DL_HSDSCH)
DCH(UL_DCH,DL_DCH), HSDPA(UL_DCH,DL_HSDSCH),
HSPA(UL_EDCH,DL_HSDSCH)
HSUPA(UL_EDCH,DL_DCH), HSPA(UL_EDCH,DL_HSDSCH)
TRUE, FALSE
D8, D16
D8, D16
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384, D512, D768,
D1024, D1536, D1800, D2048, D3600, D7200, D8640,
D10100, D13900
D8, D16, D32, D64, D128, D144, D256, D384
D8, D16, D32, D64, D128, D144, D256, D384, D608, D1280,
D2048, D2720, D5440
0~11
0~5, 8~27
0~11
NO(NO), YES(YES)
2~4094
20000~60000
3~6
OFF, ON
OFF, ON
OFF, ON

RSVDBIT32(Reserved Switch 32)
0~4294967295
0~4294967295
0~4294967295
0~511
1~16
0~255
0~511
1~16
0~120
MAY(NodeB chooses whether combine at NodeB), MUST(Must

combine at NodeB), MUST_NOT(Must combine at RNC)
0~1024
COEXIST_MEAS_THD_CHOICE_INTERFREQ(Choosing the
inter-frequency oriented parameters),
COEXIST_MEAS_THD_CHOICE_INTERRAT(Choosing the
inter-RAT oriented parameters)
1~4
0~120
PO_5/15, PO_6/15, PO_8/15, PO_9/15, PO_12/15, PO_15/15,

PO_19/15, PO_24/15, PO_30/15
PO_5/15, PO_6/15, PO_8/15, PO_9/15, PO_12/15, PO_15/15,

PO_19/15, PO_24/15, PO_30/15
1~4
1~4
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D2, D4, D8, D10, D20, D40, D80, D160
D0, D4, D8, D10, D20, D40, D80, D160

BACKGROUND, NBAMR, WBAMR
NOTUSED, USED
BIT_ALIGN(Bit aligned mode), OCTET_ALIGN(Octet aligned

mode)
D0, D1, D2, D3, D4
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25,
D26, D27, D28, D29, D30, D31, D32, D33, D34, D35, D36,
D37, D38, D39, D40, D41, D42, D43, D44, D45, D46, D47,
D48, D49, D50, D51, D52, D53, D54, D55, D56, D57, D58,
D59, D60, D61, D62, D63, D64, D65, D66, D67, D68, D69,
D70, D71, D72, D73, D74, D75, D76, D77, D78, D79, D80,
D81, D82, D83, D84, D85, D86, D87, D88, D89, D90
FALSE, TRUE
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25,
D26, D27, D28, D29, D30, D31, D32, D33, D34, D35, D36,
D37, D38, D39, D40, D41, D42, D43, D44, D45, D46, D47,
D48, D49, D50, D51, D52, D53, D54, D55, D56, D57, D58,
D59, D60, D61, D62, D63, D64, D65, D66, D67, D68, D69,
D70, D71, D72, D73, D74, D75, D76, D77, D78, D79, D80,
D81, D82, D83, D84, D85, D86, D87, D88, D89, D90
FALSE, TRUE
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25,
D26, D27, D28, D29, D30, D31, D32, D33, D34, D35, D36,
D37, D38, D39, D40, D41, D42, D43, D44, D45, D46, D47,
D48, D49, D50, D51, D52, D53, D54, D55, D56, D57, D58,
D59, D60, D61, D62, D63, D64, D65, D66, D67, D68, D69,
D70, D71, D72, D73, D74, D75, D76, D77, D78, D79, D80,
D81, D82, D83, D84, D85, D86, D87, D88, D89, D90
FALSE, TRUE
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15, D16, D17, D18, D19, D20, D21, D22, D23, D24, D25,
D26, D27, D28, D29, D30, D31, D32, D33, D34, D35, D36,
D37, D38, D39, D40, D41, D42, D43, D44, D45, D46, D47,
D48, D49, D50, D51, D52, D53, D54, D55, D56, D57, D58,
D59, D60, D61, D62, D63, D64, D65, D66, D67, D68, D69,
D70, D71, D72, D73, D74, D75, D76, D77, D78, D79, D80,
D81, D82, D83, D84, D85, D86, D87, D88, D89, D90
FALSE, TRUE
D100, D200, D400, D600, D800, D1000, D1200, D1400,

D1600, D1800, D2000, D3000, D4000, D6000, D8000
0~7
1~15
D1, D2, D4, D10, D20, D50, D100, D200, D400, D600, D800,
D1000
0~65535
None
0~500
-350~150
-350~150
-100~500
-100~500
-100~500
-350~150
-10~5
-350~150
0~255
None
0~31
Band_a, Band_b, Band_c, Band_d, BandIndNotUsed
0~16383

CHIP1536, CHIP1792, CHIP2048, CHIP2304
PScramCode0, PScramCode1, PScramCode2, PScramCode3,

PScramCode4, PScramCode5, PScramCode6, PScramCode7
0~11
0~27
D10, D20, D40, D80, D160, D320, D640, D1280
0~255
0~3
0~65535
0~255
D64, D128, D192, D256, D320, D384, D512
-350~150
-11~4
0~255
0~255
0~255
18~32
D1, D2, D3, D4
0~3
0~16777215
D64, D128, D192, D256, D320, D384, D512
0~3
0~16777215
D64, D128, D192, D256, D320, D384, D512
0~3
0~16777215
D64, D128, D192, D256, D320, D384, D512
0~3
0~16777215
D64, D128, D192, D256, D320, D384, D512
D0, D1, D2, D3, D4
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14,
D15
QPSK, 16QAM
D2, D3, D4, D5
OFF(OFF), ON(ON)
Fast_Dormancy, HSDPA_RB_Setup_Cmp_CRC
0~99999999
None
OFF, ON
FD_P2D_SWITCH, RSVDBIT1_BIT2,
FD_TAC_FORCE_D2F_SWITCH, RSVDBIT1_BIT4,
RSVDBIT1_BIT32
0~999
0~999
0~3
0~4095
None
None
None
None
TRUE, FALSE
0~65535
None
None
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~29
0~29
0~29
0~29
0~20
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~64000
-24~0
-24~0
-24~0
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
0~512
1~64
0~63
0~1000
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~29
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
-24~0
0~512
1~64
0~63
0~4095
0~65535
0~4095
0~65535
-20~20
-50~50
-50~50
-50~50
-50~50
D0, D10, D20, D30, D40, D50, D60
0~3
FALSE, TRUE
-115~-25
FALSE, TRUE
0~63
-24~0
0~15
FALSE(Not Configure the Qqualmin and Qrxlevmin),

TRUE(Configure the Qqualmin and Qrxlevmin)
-24~0
-58~-13
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
CPICH_EC/NO, CPICH_RSCP, AUTO

D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~20

D250(D250), D500(D500), D1000(D1000), D2000(D2000),
D3000(D3000), D4000(D4000), D6000(D6000), D8000(D8000),
D12000(D12000), D16000(D16000), D20000(D20000),
D24000(D24000), D28000(D28000), D32000(D32000),
D64000(D64000)
0~29
0~29
0~15
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~64000, 65535
0~64000
-24~0
-24~0
-24~0
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
-115~-25
0~63
0~63
0~63
-24~0
-24~0
-24~0
-115~-25
-115~-25
-115~-25
0~512
0~65535
0~15
1~64
0~63
0~63
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~63
0~63
1~16
0~512
OFF, ON
OFF, ON
0~100
0~100
1~64
0~63
0~63
0~65535
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19

D4000, D8000, D16000

D4000, D8000, D16000

D4000, D8000, D16000
0~29
0~29
0~29
0~29
0~29
0~29
-24~0
-115~-25
0~15
0~15
0~15
0~15
0~15
0~15
0~20
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
0~120
0~63
-29~29
0~255
-24~0
1~6
-115~-25
D250, D500
D1, D2, D4, D8
0~4095
0~65535
0~4095
0~65535
-20~20
AFFECT, NOT_AFFECT
AFFECT, NOT_AFFECT
-50~50
-50~50
-50~50
-50~50
D0, D10, D20, D30, D40, D50, D60
FALSE, TRUE
0~30
FALSE, TRUE
None
0~63
0~3
0~63
HTTP, P2P, SPI, UNRECOGNIZED
IP, Port, IPAndPort
None
None
0~65534
TCP, UDP, ALL
HIGH, MIDDLE, LOW
0~11
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
1~32
FALSE, TRUE
0~11
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~7
0~186
0~11
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~7
0~3
0~4095
0~5
10000~240000
0~240000
1000~300000
5000~30000
15000~120000
OFF, ON
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
0~100
0~65534
SPU_KPI_AUTOCURE_SWITCH
0~100
0~3
1~65533, 65535
1~256
1~256
1~65533, 65535
0~65535
None
None
1~65533, 65535
IUBLDR(Iub load reshuffling), CODELDR(Code load
reshuffling), UULDR(Uu load reshuffling), CREDITLDR(Credit
load reshuffling)
load reshuffling)
load reshuffling)
load reshuffling)
NODEB_CREDIT_LDR_SWITCH(NodeB Credit LDR Switch),

LCG_CREDIT_LDR_SWITCH(Local Cell Group Credit LDR
Switch), LC_CREDIT_LDR_SWITCH(Local Cell Credit LDR
Switch)
OFF(OFF), ON(ON)
1~115300
6~115300
1~86400
100~86400000
1~255
1~115300
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
2~65535
1~32
1~32
1~32
1~32
1~32
1~32
1~32
1~32
TEN_MSEC, MIN
1~6000
1~60
1~32
TEN_MSEC, MIN
1~6000
1~60
1~32
2~255
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
1~6000
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~32
1~32
None
0~268435455
0~65535
None
0~268435455
None
None
0~65535
0~31
0~503
1~14
0~5379
NotSupport(NotSupport), Support(Support)
False, True
0~4095
0~65535
0~65535
1~10
None
None
0~16777215
D16, D32, D64, D128, D256
-350~150
0~100
0~100
0~1279
0~2559
CH0(Channel 0), CH1(Channel 1), CH2(Channel 2),
CH3(Channel 3), CH4(Channel 4)
OFF(OFF), ON(ON)
None
None
0~4294967295
0~3
0~65535
D16, D32, D64, D128, D256
TRUE, FALSE
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
OFF(OFF), SERVICE-BASED(SERVICE-BASED), LOAD-

BASED(LOAD-BASED), DYNAMIC-BASED(DYNAMIC-
BASED)
-100~100
-100~100
1~20
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
0~10
OFF, ON
0~100
0~100
RRC(RRC connection phase), RAB(RAB setup phase),
RRC_RAB(RRC and RAB phase)
7~10
0~3
0~3
OFF, ON
1~255
D250, D500, D1000, D2000, D3000, D4000, D6000, D8000,

D12000, D16000, D20000, D24000, D28000, D32000, D64000
-115~-25
-24~0
1~65535
1~255
D250, D500, D1000, D2000, D3000, D4000, D6000, D8000,

D12000, D16000, D20000, D24000, D28000, D32000, D64000
-115~-25
-24~0
OFF, ON
None
-350~150
D16, D32, D64, D128, D256
True, False
FTP(File Transfer Protocol ), MSN(Windows Messenger),
ICMP(Internet Control Message Protocol), RTSP(Real-Time
Streaming Protocol), SMTP(Simple Mail Transfer Protocol)
OFF(Disable the ALG function), ON(Enable the ALG function)
0~4294967295
0~11
0~5, 8~27
0~11
0~3
None
None
0~65535
0~65535
OFF(Disable the NAT function), ON(Enable the NAT function)

RELIABILITY_CELL_SELFCURE_SWITCH(Cell SelfCure
Switch),
CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH(Neighboring
Cell Status Change Not Update SIB Switch)
PERFENH_R99_BRDCSTHSPA_SWITCH(R99CellBroadcastH
spaCapSwitch)
0~4294967295
0~4294967295
0~255
0~255
None
hour, min, sec
1~288
1~32
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
OFF, ON
OFF, ON
OFF, ON
None
SAAL(SAAL Link Type ), SCTP(SCTP Link Type), SAAL-

SCTP(SAAL-SCTP Link Tpye)
0~1399
0~1199

ATMTODUAL(SAAL Link TO SAAL-SCTP Dual Link ),
IPTODUAL(SCTP Link TO SAAL-SCTP Dual Link),
DUALTOATM(SAAL-SCTP Dual Link TO SAAL Link),
DUALTOIP(SAAL-SCTP Dual Link TO SCTP Link )
0~11
0~5, 8~27
0~335
OFF(OFF), ON(ON)
0~1999
0~199
OFF(OFF), ON(ON)
0~199
None
0~65535
0~11
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~7
ATM_TRANS(ATM circuit transmission), IP_TRANS(IP

transmission), ATMANDIP_TRANS(ATM and IP transmission),
HYBRID_IP_TRANS(Hybrid IP transmission)
SUPPORT(Support), NOT_SUPPORT(Not support)
0~65535
TRUE(True), FALSE(False)
R99, R4, R5, R6, R7, R8, R9
SHARE(Share), EXCLUSIVE(Exclusive)
OFF(OFF), ON(ON)
SINGLEHOST(SingleHost), PRIMHOST(PrimHost),
SECHOST(SecHost)
0~4095
0~65535
DEDICATED(Dedicated), RANSHARING(RAN Sharing),
MOCN(MOCN)
0~3
TRUE, FALSE
None
IUB_LDR(IUB LDR Algorithm), NODEB_CREDIT_LDR(NodeB

Credit LDR Algorithm), LCG_CREDIT_LDR(LCG Credit LDR
Algorithm), IUB_OLC(IUB OLC Algorithm)
0~3840
0~3840
MBR, GBR
0~4294967295
0~4294967295
0~65535
None
None
ETH/TRUNK, PPP/MP
None
None
OFF(OFF), ON(ON)
None
0~65535
ATMTRANS_IP(ATMTRANS_IP), IPTRANS_IP(IPTRANS_IP),
ATMANDIPTRANS_IP(ATMANDIPTRANS_IP)
None
None
0~11
0~5, 8~27
NO(NO), YES(YES)
0~988
None
None
0~11
0~5, 8~27
DISABLE, ENABLE
2~4094
0~7
None
NoAct(no action), BERateRed(BE traff rate reduction),

QoSRenego(uncontrolled real-time traff Qos re-negotiation),





1~10
1~10
1~10
1~10
1~10
1~10






1~10
1~10
1~10
1~10
1~10
1~10
1~10
1~10
SF128(SF128), SF256(SF256)
SF128(SF128), SF256(SF256)
8SF4(8SF4), 7SF4(7SF4), 6SF4(6SF4), 5SF4(5SF4),
4SF4(4SF4), 3SF4(3SF4), 2SF4(2SF4), SF4(SF4), SF8(SF8),
SF16(SF16), SF32(SF32), SF64(SF64), SF128(SF128),
SF256(SF256)
0~65535
None
None
0~10
0~10
0~4095
0~65535
IntraFreqNCell(IntraFreq Neighbor Cell),
InterFreqNCell(InterFreq Neighbor Cell), InterRatNCell(GSM
Neighboring Cell)
0~3
0~4095
0~1023
0~4095
CS_SHO_SWITCH, HSPA_SHO_SWITCH,
NON_HSPA_SHO_SWITCH
OFF, ON
SUPPORT_CS, SUPPORT_PS, SUPPORT_CS_AND_PS
TRUE, FALSE
0~186
R99, R4, R5, R6, R7, R8, R9
1~300
NO, YES
DL_DCCH_SWITCH, IUR_TRG_SWITCH
ATM_TRANS, IP_TRANS
CORRM_SRNSR_PSBE_RELOC,
CORRM_SRNSR_PSBE_DSCR
OFF, ON
OFF, ON
OFF, ON
OFF, ON
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH
0~4294967295
OFF, ON
0~4095
0~65535
0~3, 5~31
0~3
OFF(Offload Disable), ON(Offload Enable)

NOT_PERMIT_OFFLOAD(Not permit to take Offload),
PERMIT_OFFLOAD(permit to take Offload)
0~100
OFF(ChargeSwitch Off), ON(ChargeSwitch On)

LBO_IMEITAC_SWITCH, LBO_NONPDP_SWITCH,
RSVDBIT1_BIT29, RSVDBIT1_BIT30, RSVDBIT1_BIT31

0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~3
LBO_IMEITAC_SWITCH, LBO_NONPDP_SWITCH,
RSVDBIT1_BIT29, RSVDBIT1_BIT30, RSVDBIT1_BIT31

0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~127
0~3
None
0~99999999
None
0~3
None
None
0~3
GOLDEN_USER(GOLDEN_USER),
SILVER_USER(SILVER_USER),
COPPER_USER(COPPER_USER)
STREAMING(STREAMING), INTERACTIVE(INTERACTIVE),
BACKGROUND(BACKGROUND)
0~3
SUPP_NONE, SUPP_IUFLEX, SUPP_MOCN,

SUPP_IUFLEX_MOCN
SUPP_IUFLEX_MOCN
0~60
1~10
1~10
0~1023
OFF, ON
OFF, ON
60~900
60~900
NO, YES
NO, YES
NO, YES
NO, YES
0~3, 255
COMM_MOCN_NRI_GLOBAL_CONFIG_MODE_SWITCH,
COMM_MIB_MULTI_PLMN_LIST_ALLOWED_SWITCH,
SPARE_1_SWITCH, SPARE_2_SWITCH,
SPARE_5_SWITCH, SPARE_6_SWITCH
0~3
MBR~0
Category~1
Min~2
Max
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
0~256000
MBR~0
Category~1
Min~2
Max
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~64000
0~3
INTERACTIVE, BACKGROUND
High, Medium, Low
2~11
0~3
0~15
1~100
FALSE~0
TRUE
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
0~3
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low

High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
0~3
INTERACTIVE, BACKGROUND, IMSSIGNALLING, PTT

High, Medium, Low
R99, HSPA
D0, D8, D16, D32, D64, D128, D144, D256, D384, D608,
D1280, D2048, D2720, D5440
D0, D8, D16, D32, D64, D128, D144, D256, D384, D512,
D768, D1024, D1536, D1800, D2048, D3600, D7200, D8640,
D10100, D13900, D16000, D21000
0~3
High, Medium, Low

0~27900
0~3

ARP, TrafficClass
NONE, DCH, HSPA
0~65535
0~255
0~65535
0~255
1~32
1~256
0~1279
0~2559
-350~150
0~65535
1~32
0~4992
D1, D2
0~1
0~65535
0~255
-100~500
-100~500
-100~500
-100~500
0~65535
-100~500
-100~500
OFF, ON
OFF, ON
1~255
1~255
0~65535
0~255
0~255
V18, V36, V72, V144
TRUE, FALSE
0~65535
-10~5
LAC, RAC
0~3
1~65533, 65535
0~255
1~256
1~256
REHOSTRIGHNOW(RehostRighNow),
REHOSTDELAY(RehostDelay), REHOSTWHEN(RehostWhen)
0~3600
hour, min, sec
0~65535
0~255

0~65535
0~255

0~65535
0~255
0~15
0~15
0~15
D0.9, D0.8, D0.7, D0.6, D0.5, D0.4, D0.3, D0.2
0~65535
0~255


-35~-10
1~64
1~8
BIT2, BIT4, BIT6, BIT8, BIT12, BIT16, BIT24
0~65535
0~255
D1, D2, D3, D4
0~3
0~3
0~3
0~3
0~65535
0~255
0~16777215
-5~10
1~15
0~15
0~65535
0~255
-35~-10
1~8
1~64
0~65535
0~255
-350~150
0~14400
0~60
0~14400
0~60
0~14400
0~60
0~14400
0~60
0~64800
0~60
0~64800
0~64800
0~64800
ON, OFF
0~2
0~5120
0~2
OFF(Off), ON(On)
OFF(Off), ON(On)
1~65535
1~65535
1~65535
1~65535
D8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D6k, D8k, D12k, D16k, D24k, D32k, D48k, D64k, D96k, D128k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000

1~10000
0~38400
0~1023
0~1023
1~65535
D8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
OFF(Off), ON(On)
NO, YES
NO, YES
NO, YES
None, RateDegrade, InterFreqHO, InterRatHO
20~64000
SINGLE, COMBINE
NO, YES
NO, YES
NO, YES
20~64000
NO, YES
NO, YES
NO, YES
20~64000
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
NO, YES
0~1024
-15~15
0~512
0~512
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
1~6000
TEN_MSEC, MIN
1~6000
1~60
OFF, ON
OFF, ON
OFF, ON
OFF, ON
5~20
1~80
1~60
OFF, ON
0~3
1~65533, 65535
0~255
1~256
1~256
0~65535
0~255
1~32
1~256
0~50
0~50
1~32
0~65535
1~32
0~4992
D1, D2
0~512
0~512
0~5000
0~5000
0~5000
1~1000
1~1000
0~49
0~49
AMR, VP, PSR99, PSHSPA
ONLY_TO_INTER_RAT
0~100
0~100

FALSE, TRUE
0~16383
0~16383
0~65535
SF4, SF8, SF16, SF32, SF64, SF128, SF256
0~255
0~511
PsBlk(BLOCK PS), CsAndPsBlk(BLOCK CS AND PS)

2~30
0~4095
None
0~3
0~11
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~7
OFF(OFF), ON(ON)
OFF(OFF), ON(ON)
GERMAN(German), ENGLISH(English), ITALIAN(Italian),
FRENCH(French), SPANISH(Spanish), DUTCH(Dutch),
SWEDISH(Swedish), DANISH(Danish),
PORTUGUESE(Portuguese), FINNISH(Finnish),
NORWEGIAN(Norwegian), GREEK(Greek),
TURKISH(Turkish), HUNGARIAN(Hungarian), POLISH(Polish),
LANGUAGEUNSPECIFIED(Languageunspecified)
1~4096
0~65535
OFF(switch off), ON(switch on)
1~3600
60~3600
D16, D32, D64, D128, D256
0~100
1~5
2~10
1~5
2~20
1~360
0~60
ON, OFF
ON, OFF
ON, OFF
D8, D16, D32, D64, D128, D144, D256
None
1~60
1~10
1~10
NONE, IUCS, IUPS, IUCS_IUPS
0~4095
None
None
0~3, 5~31
0~31
1~100
ORIGCONVCALLEST, ORIGSTREAMCALLEST,
ORIGINTERCALLEST, ORIGBKGCALLEST,
ORIGSUBSTRAFFCALLEST, TERMCONVCALLEST,
TERMSTREAMCALLEST, TERMINTERCALLEST,
TERMBKGCALLEST, EMERGCALLEST,
INTERRATCELLRESELEST,
INTERRATCELLCHGORDEREST, REGISTEST,
DETACHEST, ORIGHIGHPRIORSIGEST,
ORIGLOWPRIORSIGEST, CALLREEST,
TERMHIGHPRIORSIGEST, TERMLOWPRIORSIGEST,
TERMCAUSEUNKNOWN, MBMSCALLEST, DEFAULTEST
FACH, DCH_3.4K_SIGNALLING, DCH_6.8K_SIGNALLING,

DCH_13.6K_SIGNALLING, DCH_27.2K_SIGNALLING
OFF, ON
1~15







DCH_3.4K_SIGNALLING, DCH_6.8K_SIGNALLING,










INVOKE_TRACE_SWITCH,
SYS_INFO_UPDATE_FOR_IU_RST, DRNC_DIRECT_DSCR,
RNC_SHARE_SWITCH, RNCAP_IMSI_HO_SWITCH,
TERMINAL_VERSION_DEBASE_SWITCH,
SYS_HO_OUT_CIPHER_SWITCH,
SYS_HO_CIPHER_CONFIG,
BARRED_CELL_FOR_CSDOMAIN_RST,
CR2284R1_SWITCH, CDT_MSG_FULL_TRACE,
CR2284R1_COMPATIBLE_SWITCH,
COMBINE_OPERATION_DRD_SWITCH,
UL_INTER_PROTECT_SWITCH,
FAST_DORMANCY_SWITCH,
SYS_HO_IN_CIPHER_SWITCH,
PTT_EARLY_TRANS_SWITCH_OFF,
UPLINK_MDC_ENHENCEMENT_SWITCH,
NODEB_PRIVATE_INTERFACE_SWITCH,
PTT_SPEC_LI_SWITCH_OFF,
RNC_DF_2_URA_PCH_SWITCH, FD_TAC_MATCH_SWITCH
LOAD_IRAT_HO_RNC_FILL_TL,
SEND_IDT_JUDGE_IU_RESET,
RNC_RBRECFG_DRD_FAIL_ROLLBACK_SWITCH,
RNC_CS_QUERY_UE_IMEI_SWITCH,
RNC_PS_QUERY_UE_IMEI_SWITCH,
RNC_FD_FACH_CONG_CTRL_SWITCH,
RNC_RBSETUP_DRD_FAIL_ROLLBACK_SWITCH,
FP_IUUP_TRACE_SWITCH
RSVDBIT1_BIT1, NAS_QOS_MOD_SWITCH,
RSVDBIT1_BIT15, RSVDBIT1_BIT16,
SYSHO_CSIN_PERMIT_SWITCH, RSVDBIT1_BIT18,

0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~4294967295
0~3
1~65533, 65535
0~65535
0~3
0~65535
2~10
1~5
0~3
0~3
0~186
OFF, ON
0~3
0~186
1~115300
6~115300
1~86400
100~86400000
1~255
1~115300
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
2~65535
1~32
1~32
1~32
1~32
1~32
1~32
1~32
1~32
TEN_MSEC, MIN
1~6000
1~60
1~32
TEN_MSEC, MIN
1~6000
1~60
1~32
2~255
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
1~6000
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
TEN_MSEC, MIN
1~6000
1~60
1~6000
1~32
0~65535
0~255
-350~150
0~149
0~65535
0~255
0~149
0~15
TRUE, FALSE
BIT2, BIT4, BIT6, BIT8, BIT12, BIT16, BIT24
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13,
D14, D15, D16, D17
EXISTS, NOT_EXISTS
COMMON, MCCH
0~65535
0~255
0~16777215
High, Medium, Low
2~11
0~65535
CELLID_CENTER, CELLID_RTT, OTDOA, AGPS
UE_BASED, UE_ASSISTED, UE_BASED_PREFERRED,

UE_ASSISTED_PREFERRED
NODELIVERY, DELIVERY
REFERENCE_TIME_FOR_GPS,
REFERENCE_LOCATION_FOR_GPS, DGPS_CORRECT,
GPS_NAVGMODEL, GPS_IONOSPHERIC_MODEL,
GPS_UTC_MODEL, GPS_ALMANAC, GPS_ACQ_ASSIST,
GPS_REALTIME_INTEGRITY
GPS_REALTIME_INTEGRITY
4~16


OFF, ON
NO, YES
DRD, MEAS_BASED
R5_POSDATA_SWITCH,
LAST_KNOWN_SERVICE_AREA_SWITCH
OFF, ON
0~29
0~29
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
-24~0
RNC_CENTRIC(RNC CENTRIC Mode), SAS_CENTRIC(SAS
CENTRIC Mode), SAS_CENTRIC_PREFERRED(SAS
CENTRIC PREFERRED Mode)
D250, D500, D1000, D2000, D3000, D4000, D6000, D8000,

D12000, D16000, D20000
POINT, POINT_WITH_UNCERTN,
ELPSD_POINT_WITH_UNCERTN_ELLIPSE,
ELPSD_POINT_WITH_ALT,
ELPSD_POINT_WITH_ALT_AND_UNCERTN_ELPSD,
ELPSD_ARC, AUTOMATIC
0~4095
0~65535
CELL_ANTENNA, CELL_CENTER, BOTH
DEG(Degree), SEC(Degree Minute and Second)
MET(Metric System), IMP(British Measurement)
-90000000~90000000
-180000000~180000000
-32767~32767
1~100000
0~3600
0~3600
-32767~32767
-10000~10000
NLOS_ENVIRONMENT, LOS_ENVIRONMENT,
MIXED_ENVIRONMENT
INACTIVE, ACTIVE
INACTIVE, ACTIVE
INACTIVE, ACTIVE
-90000000~90000000
-180000000~180000000
-32767~32767
0~1800000
0~1800000
0~179
0~990
None
None
None
None
-107502~107502
3~328080
-107502~107502
-32808~32808
-107502~107502
0~5905440
0~5905440
0~3248
1~8
0~7
0~7
0~7
0~7
0~7
0~15
1~100
FALSE~0
TRUE
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
1~100
0~500
0~500
1~255
0~400
1~100
1~65535
1~255
RT(Real time service), NRT(Non real time service), ALL(All
service)
0~65535
0~255
-350~150
1~10000
1~10000
1~5000
1~10000
1~10000
1~3000
300~300000
1~10000
300~300000
300~300000
1~10000
1~10000
1~10000
1~300000
1~10000
1~10000
1~10000
1~10000
1~10000
1~300000
1~300000
1~300000
1~20000
1~60000
1~20000
1~10000
1~20000
1~10000
1~10000
1~20000
1~10000
1~255
1~10000
1~10000
1~10000
1~65535
1~65535
0~15
High, Medium, Low

High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low
High, Medium, Low

High, Medium, Low
High, Medium, Low
0~111
0~6, 11~19, 21~28, 40~69, 70~111

BACKGROUND
SPEECH, UNKNOWN
0~256000000
1~15
1~15
HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM
GSM, GPRS, EDGE
NORMAL, SILENT
APPLIED_ON_UPLINK, APPLIED_ON_DOWNLINK,
APPLIED_ON_BOTH
HO_TO_EUTRAN_SHOULD_BE_PERFORM,
HO_TO_EUTRAN_SHALL_NOT_BE_PERFORM
0~111
UPLINK, DOWNLINK
D16, D32, D64, D128, D256, D512, D1024, D2K, D3K, D4K,
D6K, D8K, D12K, D16K, D24K, D32K, D48K, D64K, D96K,
D128K, D192K, D256K, D384K, D512K, D768K
D8, D16, D32, D64, D128, D256, D512, D1024, D2K, D3K,
D4K, D6K, D8K, D12K, D16K, D24K, D32K, D48K, D64K,
D96K, D128K, D192K, D256K, D384K, D512K
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000, D10000, D15000,
D20000, D25000, D30000
D250, D500, D1000, D2000, D4000, D8000, D16000

D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000, D10000, D15000,
D20000, D25000, D30000
D250, D500, D1000, D2000, D4000, D8000, D16000
0~1023
0~1023
0~1023
0~1023
0~1023
0~1023
0~111
TRCH_HSDSCH, TRCH_EDCH_2MS, TRCH_EDCH_10MS
D10, D20, D30, D40, D50, D60, D70, D80, D90, D100, D120,
D140, D160, D200, D300, D400
D4, D6, D8, D12, D16, D24, D32, D64, D128
D1, D2, D3, D4, D5, D6, D7, D8
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
FALSE, TRUE
D20, D40, D60, D80, D100, D120, D140, D160, D180, D200,
D250, D300, D400, D500, D750, D1000, D1250, D1500,
D1750, D2000, D2500, D3000, D3500, D4000, D4500, D5000,
D7500
500~25500
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
1~5000
D2, D10, D20, D50, D100, D200, D500, D1000
1~64
1~64
0~111
0~2
TRCH_EDCH_2MS, TRCH_EDCH_10MS
TRUE, FALSE
TRUE, FALSE
TRUE, FALSE
0~255
0~255
0~255
0~3
D1, D2, D3, D4, D5, D6, D7, D8
0~127
0~127
0~127
0~127
0~127
0~127
0~127
0~127
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
0~37
0~37
TRUE, FALSE
PO_8/15, PO_11/15, PO_15/15, PO_21/15, PO_30/15,

PO_42/15, PO_60/15, PO_84/15
0~6
0~6
0~6
0~111
0~2
TRCH_DCH, TRCH_EDCH_2MS, TRCH_EDCH_10MS
1~5
-63~0
0~5000
0~15
0~15000
0~15000
0~111
0~82
0~82
0~82
0~82
1~512
1~512
1~512
0~56
0~56
0~111
0~2
TRCH_DCH, TRCH_HSDSCH, TRCH_EDCH_2MS,

TRCH_EDCH_10MS
TRCH_DCH, TRCH_HSDSCH
1~5
AM, UM, TM
SENDER_PARA, RECEIVE_PARA, FLOWCONTROL_PARA
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
D50, D100, D150, D200, D250, D300, D350, D400, D450,

D500, D550, D600, D700, D800, D900, D1000
D1, D4, D6, D8, D12, D16, D24, D32
FALSE, TRUE
TIMER_BASED_WITH_EXPLICIT_SIGNALLING,
DISCARD_AFTER_MAX_DAT_RETRANSMISSIONS,
NO_DISCARD
NOTUSED,
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING
D50, D60, D70, D80, D90, D100, D120, D140, D160, D180,
D200, D300, D400, D500, D700, D900
D100, D250, D500, D750, D1000, D1250, D1500, D1750,

D2000, D2500, D3000, D3500, D4000, D4500, D5000, D7500
D1, D4, D6, D8, D12, D16, D24, D32
D10, D20, D30, D40, D50, D60, D70, D80, D90, D100
D2, D3, D4, D5, D6, D7, D8, D9, D10, D15, D20, D25, D30,
D35, D40
D50, D60, D70, D80, D90, D100, D120, D140, D160, D180,
D200, D300, D400, D500, D700, D900
D1, D4, D6, D8, D12, D16, D24, D32
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D15, D20, D25, D30,
D35, D40
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
FALSE, TRUE
NOTUSED, D10, D20, D30, D40, D50, D60, D70, D80, D90,
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
NOTUSED, D100, D200, D300, D400, D500, D750, D1000,
D2000
FALSE, TRUE
FALSE, TRUE
FALSE, TRUE
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
NOTUSED, D1, D2, D4, D8, D16, D32, D64, D128
NOTUSED, D1, D4, D16, D64

NOTUSED, D100, D200, D300, D400, D500, D750, D1000,
D2000
FALSE, TRUE
FALSE, TRUE
0~500000
40~60000
0~10
0~1000
1~100
0~1000
0~1000
1~100
0~1000
0~1000
0~4
TRCH_EDCH_2MS, TRCH_EDCH_10MS
TRUE, FALSE
TRUE, FALSE
TRUE, FALSE
0~255
0~255
0~255
0~3
D1, D2, D3, D4, D5, D6, D7, D8
0~127
0~127
0~127
0~127
0~127
0~127
0~127
0~127
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15
0~37
0~37
TRUE, FALSE
PO_8/15, PO_11/15, PO_15/15, PO_21/15, PO_30/15,

PO_42/15, PO_60/15, PO_84/15
0~6
0~6
0~6
0~4
TRCH_EDCH_10MS
TRCH_DCH, TRCH_HSDSCH
1~5
0~3
AM, UM
EDIT_SENDER_PARA, EDIT_RECEIVE_PARA
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
D50, D100, D150, D200, D250, D300, D350, D400, D450,

D500, D550, D600, D700, D800, D900, D1000
NO_DISCARD
NOTUSED,
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING
D50, D60, D70, D80, D90, D100, D120, D140, D160, D180,
D200, D300, D400, D500, D700, D900
D100, D250, D500, D750, D1000, D1250, D1500, D1750,

D2000, D2500, D3000, D3500, D4000, D4500, D5000, D7500
D1, D4, D6, D8, D12, D16, D24, D32

D10, D20, D30, D40, D50, D60, D70, D80, D90, D100
D2, D3, D4, D5, D6, D7, D8, D9, D10, D15, D20, D25, D30,
D35, D40
D50, D60, D70, D80, D90, D100, D120, D140, D160, D180,
D200, D300, D400, D500, D700, D900
D1, D4, D6, D8, D12, D16, D24, D32
D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D15, D20, D25, D30,
D35, D40
D1, D8, D16, D32, D64, D128, D256, D512, D768, D1024,
D1536, D2047, D2560, D3072, D3584, D4095
FALSE, TRUE
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
NOTUSED, D100, D200, D300, D400, D500, D750, D1000,

D2000
FALSE, TRUE
FALSE, TRUE
FALSE, TRUE
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
D100, D110, D120, D130, D140, D150, D160, D170, D180,
D190, D200, D210, D220, D230, D240, D250, D260, D270,
D280, D290, D300, D310, D320, D330, D340, D350, D360,
D370, D380, D390, D400, D410, D420, D430, D440, D450,
D460, D470, D480, D490, D500, D510, D520, D530, D540,
D550, D600, D650, D700, D750, D800, D850, D900, D950,
D1000
NOTUSED, D100, D200, D300, D400, D500, D750, D1000,

D2000
MeasurementQuantity(MeasurementQuantity), Both(Both)
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19
0~512
RSRP(Reference Signal Receiving Power), RSRQ(Reference

Signal Receiving Quality)
0~15
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
1~97
1~34
UEA0, UEA1
1~65535
D8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000

D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D8, D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D250, D500, D1000, D2000, D4000, D8000, D16000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
1~10000
0~384
0~1023
0~1023
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
D0, D10, D20, D40, D60, D80, D100, D120, D160, D200,
D240, D320, D640, D1280, D2560, D5000
D16, D32, D64, D128, D256, D512, D1024, D2k, D3k, D4k,
D192k, D256k, D384k, D512k, D768k
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
1~65535
UIA1
0~3
None
None
0~65535
0~3
INTERACTIVE, BACKGROUND, IMSSIGNALLING, PTT
High, Medium, Low
R99, HSPA
D0, D8, D16, D32, D64, D128, D144, D256, D384, D608,
D1280, D2048, D2720, D5440
D0, D8, D16, D32, D64, D128, D144, D256, D384, D512,
D768, D1024, D1536, D1800, D2048, D3600, D7200, D8640,
D10100, D13900, D16000, D21000
High, Medium, Low
0~27900
D3.4, D13.6, D27.2
D3.4, D13.6, D27.2
D0, D8, D16, D32, D64, D128, D144, D256, D384
D0, D8, D16, D32, D64, D128, D144, D256, D384
D0, D8, D16, D32, D64, D128, D144, D256, D384
D0, D8, D16, D32, D64, D128, D144, D256, D384

0~100
5~20
0~100
5~20
0~100

ARP, TrafficClass
NONE, DCH, HSPA
None
OFF(Not Support VIP users signal log report), ON(Support VIP
users signal log report)
ALGORITHM_OFF(WPS Algorithm Switch OFF),
ALGORITHM_ON(WPS Algorithm Switch ON)
PRIORITY1(WPS USER PRIORITY 1), PRIORITY2(WPS

USER PRIORITY 2), PRIORITY3(WPS USER PRIORITY 3),
USER PRIORITY 11), PRIORITY12(WPS USER PRIORITY
12), PRIORITY13(WPS USER PRIORITY 13),
PRIORITY14(WPS USER PRIORITY 14)
0~11
SAALLNK, IPOAPVC, AAL2PATH
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26
0~1399
None
None
0~4599
1~4294967295
NO_LOOP(No loop), LOCAL_LOOP(Local loop)
1~65535
0~11
0~5, 8~27
None
2~4094
0~11
0~5, 8~27
NCOPT(Optical Port)
0~167
0~335
0~31
0~7
0~11
0~5, 8~27
NCOPT(Optical Port)
0~167
0~335
0~31
0~7
VPLCX(VPL cross), VCLCX(VCL cross)
0~4095
32~65535
0~4095
32~65535
100~1999
100~1999
0~1399
Enumeration Number/Bit Unit
Not involved None
Not involved None
Not involved None
UNI~3, IMA~4, FRAATM~5, NCOPT~6,

ATMLOGICPORT~7, NULL~255 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

NO~0, YES~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
PEER~0, LOCAL~1 None
Not involved None
Not involved ms
R99~0, HSPA~1, SHARE~2 None
Not involved None
Not involved None
Not involved None
NO~0, YES~1 None
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved None
IUB~0, IUR~1, IUCS~2, IUPS~3 None
ATM~0, IP~1, ATM_IP~2, HYBRID_IP~3 None
SHARE~0, EXCLUSIVE~1 None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
IUB~0, IUR~1, IUCS~2, IUPS~3,

UNI_AAL2SWITCH~4, NNI_AAL2SWITCH~5 None
Not involved None
NO~0, YES~1 None
Not involved None

NO~0, YES~1 None
Not involved None
Not involved None
Not involved None
Not involved None
CS1~1, CS2~2 None
Not involved None
Not involved s
Not involved None
Not involved None

Not involved %
Not involved %
DISABLE~0, ENABLE~1 None
Not involved s
Not involved None
Not involved d
Not involved None
Not involved None
Critical~1, Major~2, Minor~3, Warning~4 None
ON~32, OFF~255 None
Not involved None
Not involved None
CLOSE~0, OPEN~1 None
Not involved None
BOOL~0, VALUE~1 None
LOW~0, HIGH~1 None
Not involved None
Not involved None
Not involved None
unshielded~0, shielded~1 None
ON~0, OFF~1 None
Not involved d
ON~1, OFF~0 None
Not involved None
Not involved None

Hub~0, Leaf~1 None
AEUa~2, AOUa~5, UOIa~7, AOUc~13, UOIc~15 None
Not involved None

IMA~4, UNI~3, FRA~5, NCOPT~6,
ATMLOGICPORT~7 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved kbit/s
Not involved kbit/s
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

UBR~1, CBR~4, RTVBR~3, NRTVBR~2,
UBR_PLUS~0 None
CELL/S~1, KBIT/S~2 None
Not involved None
Not involved None
Not involved None
Not involved byte
Not involved 100ns
Not involved None
Not involved None
Not involved None
BFD_OFF~0, BFD_ON~1 None
Not involved None
nonrpt~0, rpt~1 None
Not involved None

Not involved None
SCU~1, INT~7 None
YES~0 None
SCUb~113 None
INT~7, DPU~6, XPU~3, OMU~11, SAU~15, NIU~99 None

PEUa~1, AEUa~2, FG2a~3, GOUa~4, AOUa~5,
POUa~6, UOIa~7, AOUc~13, POUc~14, UOIc~15,
FG2c~17, GOUc~18, SPUa~48, SPUb~50,
DPUb~65, DPUe~69, OMUa~84, OMUb~85,
OMUc~86, SAUa~254, NIUa~72 None
OAM~1, UCP~6, RUCP~8, UUP~13, ATM~20,

IP~21, SAU~254, NIU~38 None
YES~0, NO~1 None
Not involved None
Not involved None
NO~0, YES~1 None
LS~1, BAK~0 None
Not involved None
CENTRALIZED~1, DISTRIBUTED~2 None
Not involved None

G_15~15, G_16~16, G_17~17, G_18~18,
G_19~19, G_20~20, G_21~21, G_22~22,
G_23~23, G_24~24, G_25~25, G_26~26,
G_27~27, G_28~28, G_29~29, G_30~30, G_31~31 None
Not involved None

G_15~15, G_16~16, G_17~17, G_18~18,
G_19~19, G_20~20, G_21~21, G_22~22,
G_23~23, G_24~24, G_25~25, G_26~26,
G_27~27, G_28~28, G_29~29, G_30~30, G_31~31 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
10~10, 100~100, 1000~1000 ms
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
LocalMep~0, RemoteMep~1 None
Not involved None
ETHER~0, TRUNK~9 None
Not involved None
Not involved None
Not involved None
MPS~0, EPS~1 None
Not involved None
Not involved None

AEUa~2, PEUa~1, AOUa~5, POUa~6, UOIa~7,
AOUc~13, POUc~14, UOIc~15 None
Not involved None
NO~0, YES~1 None
Not involved None
NO~0, YES~1 None
OFF~0, ON~1 None

OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
MANUAL~0, AUTO~1, FREE~2 None
Not involved None
Not involved None
BITS1-2MHZ~1, BITS2-2MHZ~2, BITS1-2MBPS~3,

BITS2-2MBPS~4, 8KHZ~5, GPS~6,
LINE1_8KHZ~9, LINE2_8KHZ~10, BITS1-
1.5MBPS~11, BITS2-1.5MBPS~12 None
GCUa~82, GCGa~83 None
ON~1, OFF~0 None
ALL~0, ONLY_SSL~1 None
Not involved None
Not involved None
AOUa~5, POUa~6, AOUc~13, POUc~14 None
ALL~0, PORT~1, SINGLE~2 None

Not involved None
Not involved None
NULL~0, 1BYTE~1, 16BYTE~16, 64BYTE~64 None
Hexadecimal~0, Character_String~1 None
Not involved None
Not involved None
ZERO~0, SPACE~1 None
Not involved None
OFF~0, SERVICE-BASED~1, LOAD-BASED~2,

DYNAMIC-BASED~3 None
Not involved None
Not involved None

SCU~1, GCU~2, MPU~16, UCP~17, DPU~6,
INT~7, NIU~99 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
NBAP_CCP~0, NBAP_NCP~1, IUB_OAM~2,
ALCAP~3 None
Not involved %
Not involved None
Not involved None
Not involved None
LOGIC_IP~0, IPOA_CLIENT_IP~1 None
Not involved None
Not involved None
Not involved byte
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
AEUa~2, AOUa~5, AOUc~13, PEUa~1, POUa~6,

POUc~14 None
ALL~0, SINGLE~1 None
Not involved None
NO~0, YES~1 None
E1_UNBA~0, E1_BA~1, T1~2, E1~4 None
E1_DOUBLE_FRAME~4,
E1_CRC4_MULTI_FRAME~5,
T1_SUPER_FRAME~3,
T1_EXTENDED_SUPER_FRAME~2 None
E1_DOUBLE_FRAME~4,
T1_SUPER_FRAME~3,
E1_DOUBLE_FRAME~4,
T1_SUPER_FRAME~3,
B8ZS~2, HDB3~3, AMI~5, AMI_ZCS~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None

Not involved None
Not involved None
Not involved None
AEUa~2, AOUa~5, AOUc~13, PEUa~1, POUa~6,

POUc~14 None
Not involved None
NO_LOOP~1, REMOTE_LOOP~3,
LINE_REM_LOOP~4, LOCAL_LOOP~5,
PAYLOAD_LOOP~2, SIN_CHN_LOC~7,
SIN_CHN_REM~8 None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
Not involved min
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
VOLTAGE~0, CURRENT~1 None
Not involved V
Not involved V
Not involved V
Not involved V
degree
Not involved Celsius
degree
Not involved Celsius
Not involved %
Not involved %
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved V or A
Not involved None
Not involved None

power~0, env~1, sig~2, trunk~3, hardware~4,
software~5, run~6, comm~7, service~8, handle~9,
integrity~11, ope~12, physical~13, sec~14, time~15 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
FG2a~3, GOUa~4, FG2c~17, GOUc~18 None
FE~0, GE~1 None
Not involved None
ENABLE~1, DISABLE~0 None
1000M~2, AUTO~5 None

Not involved byte
OFF~0, ON~1 None
Not involved %
OFF~0, ON~1 None
Not involved None
OFF~0, ON~1 None
O1E3_R5E4~0, O5E4_R1E4~1, O1E4_R5E5~2,

O5E5_R1E5~3, O1E5_R5E6~4, O5E6_R1E6~5 None
Not involved packet/s
V7~0, V8~1 None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
LOAD_SHARING~0, ACTIVE_STANDBY~1 None

Not involved None
NON-REVERTIVE~0, REVERTIVE~1 None
STATIC_LACP~0, MANUAL_AGGREGATION~1 None
Not involved %
OFF~0, ON~1 None
Not involved None
V7~0, V8~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
LOAD_SHARING~0, ACTIVE_STANDBY~1 None

Not involved None
Not involved min
Not involved s
OFF~0, ON~1 None
NORMAL_FAN~0, IND_FAN~1 None
Not involved None
HW_AUTO_TEMPERATURE_CONTROL~1,
SPECIFY_RATE~2, SOFTWARE_CONTROL~3 None
Not involved None
SCU~1, GCU~2, XPU~3, DPU~6, INT~7, NIU~99 None
Not involved None
Not involved None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
Not involved None
ON~1, OFF~0 None
ON~1, OFF~0 None

ON~1, OFF~0 None
ON~1, OFF~0 None
Not involved None
Not involved None
Not involved None
Not involved None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
FRAATM~1, FRAIMA~2 None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

AUTO~0, PLAINTEXT~1, ENCRYPTED~2 None
YES~1, NO~0 None
Not involved None
Not involved None
Not involved None
Not involved None
AUTO~0, PLAINTEXT~1, ENCRYPTED~2 None
DEFAULTPORT~0, CUSTOMPORT~1 None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
RNC~0, NODEB~1, NRNC_RNC~2,

NRNC_NODEB~3 None
Not involved None
Not involved None
Not involved min
Not involved min
DEG~0, SEC~1 None

MET~0, IMP~1 None
Not involved degree
Not involved degree
Not involved m
Not involved None
Not involved None
Not involved feet
Not involved min
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
ECHOREPLY~0, UNREACH~3,
SOURCEQUENCH~4, REDIRECT~5, ECHO~8,
ROUTERADVERT~9, ROUTERSOLICIT~10,
TIMXCEED~11, PARAMPROB~12, TSTAMP~13,
TSTAMPREPLY~14, IREQ~15, IREQREPLY~16,
MASKREQ~17, MASKREPLY~18 None
Not involved None
Not involved None
AEUa~2, AOUa~5, AOUc~13 None
Not involved None

Not involved None
Not involved None
D32~32, D64~64, D128~128, D256~256 None
Not involved None
V1.0~1, V1.1~3 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
IU~0, IUB~1, IP_PATH~3, AL~4, GTPU~5,

CELL_KPI~6, SIGNALING_PLANE_LOOP~7,
SHB~10 None
AOUA~0, POUA~1, UOIA_ATM~2, UOIA_IP~3,
FG2A~4, GOUA~5, GOUC~6, POUC~7, FG2C~8,
UOIC_ATM~9, AOUC~10 None
AOUA~0, POUA~1, UOIA_ATM~2, UOIA_IP~3,

FG2A~4, GOUA~5, AEUA~6, PEUA~7, GOUC~8,
POUC~9, FG2C~10, UOIC_ATM~11, AOUC~12 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
FG2a~3, GOUa~4, FG2c~17, GOUc~18 None

OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
Not involved None

FG2a~3, GOUa~4, UOIa~7, FG2c~17, GOUc~18,
POUc~14 None
Hub~0, Leaf~1 None
Not involved None

ETHER~0, IPLOGICPORT~8, TRUNK~9, PPP~1,
MP~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
OFF~0, ON~1 None
Not involved kbit/s
Not involved kbit/s
Not involved %
Not involved kbit/s
Not involved byte
Not involved %
Not involved %
Not involved kbit/s
Not involved ms
Not involved None
Not involved %
Not involved None
Not involved ms
Not involved ms
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None

Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
FPMUX~0, UDPMUX~1 None
Not involved None
Not involved None
NO~0, YES~1 None

BE~0, AF11~1, AF12~2, AF13~3, AF21~4,
AF22~5, AF23~6, AF31~7, AF32~8, AF33~9,
AF41~10, AF42~11, AF43~12, EF~13 None
Not involved byte
Not involved byte
Not involved ms
NORTPCOMP~1, RTPCOMP~2 None
NORTPCOMP~1, RTPCOMP~2 None
Not involved None
FPMUX~0, UDPMUX~1 None
Not involved None
Not involved None

IMA~4, UNI~3, FRAATM~5, NCOPT~6,
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
IUB~0, IUPS~1, OTHER~2 None
Not involved None
Not involved None

IP~0, HYBRID_IP~1 None
QoS~18, BE~4, AF11~5, AF12~6, AF13~7,

AF21~8, AF22~9, AF23~10, AF31~11, AF32~12,
AF33~13, AF41~14, AF42~15, AF43~16, EF~17,
LQ_QOS~33, LQ_BE~19, LQ_AF11~20,
LQ_AF12~21, LQ_AF13~22, LQ_AF21~23,
LQ_AF22~24, LQ_AF23~25, LQ_AF31~26,
LQ_AF32~27, LQ_AF33~28, LQ_AF41~29,
LQ_AF42~30, LQ_AF43~31, LQ_EF~32 None
Not involved None
Not involved None
Not involved None
Not involved kbit/s
Not involved kbit/s

NULL~0, IPLGCPORT~1, RSCGRP~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
ENABLED~1, DISABLED~0 None
Not involved None
Not involved s
Not involved None
Not involved byte
UDP~1, ICMP~0 None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
HIGH~80, LOW~120 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
NORMAL~0, FORCE~1 None
Not involved None
Not involved None
Not involved %
Not involved %
UMTS~1 None
NO~0, YES~1 None
Not involved None
Not involved Erl
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

PDCP~0, AMRC~1, TFOTRFO~2,
INDIRECRETRY~3, INTERRATDIRECRETRY~4,
INTERRATREDIRECT~5, CBS~8, CELLID~9,
OTDOA~10, AGPS~11, PUC~12,
INTRACELLLDB~13, INTERCELLLDB~14,
MULTIRAB~15, HCS~17, RABDOWNSIZING~18,
QCPE~19, INTERSERVICEHO~20,
INTERLOADHO~21, IUQOSRENEG~22,
LCSCZ~23, HSDPA~24, IUFLEX~26, IUBSC~27,
IUBIP~30, MBMS~31 None
WBAMR~0, HSUPA~1, RANSHARE~2,

HSDPA3.6M~3, HSDPA7.2M~4, ROHC~5,
IURLC~6, NACC~7, PSHBUG~8, IMSIBH~9,
32HSDPAUPERCELL~10,
64HSDPAUPERCELL~11, STMTRAONHSDPA~12,
HSDPASTATETRAN~13, HSDPADRD~14,
ENHANCEDIUFLEX~15, STMTRAONHSUPA~16,
ATMIPDUALSTACK~17, IPTRANINIUR~18,
IPTRANINIU~19, FRACTIONALIP~20,
IPIUBOVERBOOKING~21, FRACTIONALATM~22,
ATMOVERBOOKING~23, IUBHYBRIDIPTRAN~24,
MBMS8CHANNELPERCELL~25,
256KBPSCHNLRATEONMBMS~26,
MBMSFLCFLD~27, VTFTSFIHO~28,
CBIHBUMTSANDGSMGPRS~29,
SRNSRELOCATION~30,
SRNSRWHHANDOVER~31 None
SRNSRWCUPDATE~0,
LOSSLESSSRNSRELCT~1,
INTERFREQHARDHNDV~2,
IMPRVEDWNLNKCVRGE~3,
ACRWHENSPUOVER~4, CBWHENIUIFAULT~5,
3G2GCOMMON_LOAD~6, FP_MUX~7,
HSDPA_OVER_IUR~8,
HS_DPCCH_PREAMBLE_SUPPORT~9,
HSUPA_2ms_10ms~10, HSUPA_5_74MBPS~11,
HSUPA_OVER_IUR~12,
HUB_IUB_OVERBOOKING~13,
IMS_SIGNALING_OVER_HSPA~14,
DYN_BANDWIDTH_CTROL_IUB_IP~15,
MBMS_OVER_IUR~16,
MBMS_P2P_OVER_HSDPA~17,
MBMS_ENHANCED_BROADCAST~18,
MBMS_ADMISSION_ENHANCE~19,
RAN_SHARING_ENHANCED_PACKAGE~20,
SRB_OVER_HSDPA~21, SRB_OVER_HSUPA~22,
MULTI_FBNM~23, HSDPA_13_976MBPS~24,
BFD_ARP_IP~25, INTER_FHHBDLQOS~26,
INTER_RHBDLQOS~27,
MBMS_16_CHANNELS_PER_CELL~28,
60_HSUPA_USERS_PER_CELL~29, TPMT~30,
AQM~31 None
DYNAMIC_POWER_ESTIMATION_FOR_MTCH~0,
ONE_TUNNEL~1,
MULCAR_SWOFF_BASEDON_TRALOAD~2,
CS_OVER_HSPA~3, VOIP_OVER_HSPA~4,
96_HSDPA_USERS_PER_CELL~5,
HSPA_DOWN28_PER_USER~6,
HSPA_DOWN21_PER_USER~7,
96_HSUPA_USERS_PER_CELL~8,
MSCH_SCHEDULING~9, MBMS_CHANNEL~10,
ENHANCED_CELL_FACH~11,
CPC_HS_SCCH~12, CPC_DTX_DRX~13,
UPLINK_MACRO_RECEIVE~14,
DOMAIN_ACCESS_CONTROL~15,
SERVICE_IN_RRC~16, TCP_ACCELERATOR~17,
UPLINK_CONTROL_OF_USER~18,
MOCN_PACKAGE~19, IUCS_UDP_MUX~21,
RNC_NODE_REDUNDANCY~22,
DOWNLNK_ENHANCED_L2~23,
DIFF_SERVICE_ON_SPI_WEIGHT~24,
HSUPA_ADAPTIVE_RETRANSMISSION~25,
SIMPLE_CELL_BORADCAST~26,
SATELLITE_TRANS_ON_IU~27,
IUR_G_NACC~29, IUR_G_LBB~30,
IUR_G_SDB~31 None
IUR_G_HBL~0, EHSPA_42M_DL~1,
UL_MOBILITY_P1~2, HSDPA_128_UPC~3,
HSUPA_128_UPC~4, IUPC_FOR_LCS~5,
MULTI_FREQ_BNM_EH~6,
WARN_OF_DISASTER~7,
QUAL_IMPROVE_FOR_SS~8,
TTI_FOR_BE_SBC~9,
INTERSYS_REDIRECT_BOD~10,
MEASUREMENT_BD_RETRY~11,
FAST_DORMANCY_ENHANCE~12,
HSUPA_COVERAGE_ENHANCE~13,
ENHANCE_UL_FOR_CELL_FACH~14,
ENHANCE_DRX~16,
HSPA_DL84M_PER_USER~17,
HSPA_UL11.5M_PER_USER~18,
PS_SERVICE_REDIRECT_FU2L~19,
VIDEO_PHONE_RESTRICT~20,
OPT_R99HSUPA_USER_FAIRNESS~21,
ADAPTIVE_CONF_TC_PO_HSUPA~23,
WEB_BROWSING_ACCELERATION~24,
P2P_RATE_CONTROL~25,
FREE_USER_RESOURCE_RESERVE~26,
FLEX_HSPA_TECH_SELECTION~27 None
Not involved None
ON~1, OFF~0 None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
LFB~1, CL~0 None

monitor~1, host_gate~2, ems_gate~3, authority~4,
configure~5, maintain~6, stat~7, alarm~8,
software~9, ftp_server~10, sntp~11,
ems_agent~13, omu_manager~14, weblmt~15,
cfa~16, debug_log~17 None
TASKID~1, CMDCODE~2 None
Not involved None
Not involved None

Not involved d
Not involved None
OPLOG_TYPE~0, SECLOG_TYPE~1 None
Not involved None
Not involved None
Not involved None
M3UA_SGP~1, M3UA_IPSP~2, M3UA_SS7SP~3,

M3UA_SP~4 None
Not involved None
Not involved None
Not involved None
Not involved None
M3UA_ASP~0, M3UA_IPSP~2 None
Not involved None
Not involved None
Not involved None
Not involved None

B0000~0, B0001~1, B0010~2, B0011~3, B0100~4,
B0101~5, B0110~6, B0111~7, B1000~8, B1001~9,
B1010~10, B1011~11, B1100~12, B1101~13,
B1110~14, B1111~15 None
M3UA_OVERRIDE_MOD~1,
M3UA_LOADSHARE_MOD~2 None
M3UA_ASP~0, M3UA_IPSP~2 None
Not involved s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
M3UA_MASTER_MOD~1, M3UA_SLAVE_MOD~0 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
MEASRST~0, HOSTRST~1 None
Not involved None
Not involved None
Not involved None
Not involved None

PEUa~1, POUa~6, POUc~14 None
IP~21 None
Not involved None
MLPPP~0, MCPPP~1 None
NO~0, YES~1 None
Not involved None
Not involved None
Not involved None
Not involved None
LONG~0, SHORT~1 None
Not involved None

Not involved byte
No_HC~3, UDP/IP_HC~1, RTP/UDP/IP_HC~0 None
Disable~0, Enable~1 None
Not involved None
Not involved None

Not involved ls
OFF~0, ON~1 None
Not involved None
Not involved %
NO_V~0, PAP_V~1, CHAP_V~2 None
SERVER~0, CLIENT~1 None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
O1E3_R5E4~0, O5E4_R1E4~1, O1E4_R5E5~2,

OFF~0, ON~1 None

ERR_PFM_5E6~2, ERR_PFM_1E5~3,
ERR_PFM_5E3~8 None
ERR_PFM_1E3~7 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved byte
Not involved byte
Not involved ls
ERR_PFM_5E3~8 None
ERR_PFM_1E3~7 None
Not involved None
Not involved None
PEUa~1, POUa~6, POUc~14 None
Not involved None
Not involved None
Not involved None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
Not involved s
Not involved s
None~0, 16bit~1, 32bit~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
NON-REVERTIVE~0, REVERTIVE~1 None
Not involved s
NOT-INDICATE-END~0, INDICATE-END~1 None
1E-3~3, 1E-4~4, 1E-5~5, 1E-6~6, 1E-7~7, 1E-8~8,

1E-9~9 None
HIGH~0, LOW~1 None
MODE1~1, MODE2~2, MODE3~3, MODE4~4 None
Not involved None
Not involved None
Not involved None

CLEAR~16, LOP~15, FS~14, MS~8, EXERS~4 None
Not involved None
Not involved None
B0000~0, B0001~1, B0010~2, B0011~3, B0100~4,

B0101~5, B0110~6, B0111~7, B1000~8, B1001~9,
B1010~10, B1011~11, B1100~12, B1101~13,
B1110~14, B1111~15 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved None
Not involved None
Not involved None

WNF~0, DNF~1 None
Not involved None
Not involved None
IUCS~0, IUPS~1, IUR~2, IUCS_RANAP~3,

IUCS_ALCAP~4, AAL2SWITCH~5, STP~6,
IUPC~11 None
B0000~0, B0001~1, B0010~2, B0011~3, B0100~4,
B0101~5, B0110~6, B0111~7, B1000~8, B1001~9,
B1010~10, B1011~11, B1100~12, B1101~13,
B1110~14, B1111~15 None
NO~0, YES~1 None
OFF~0, ON~1 None
MTP3~0, M3UA~1, MTP3_M3UA~2 None
M3UA_FIRST~1, MTP3_FIRST~2 None
ITUT~0, ANSI~1, TTC~2 None
ALL~0, BOARD~3, PORT~4, DSP~5 None
Not involved None
Not involved None
Not involved None
Not involved None

ALL~1, ONEBYONE~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Administrators~0, Operators~1, Users~2, Guests~3,
Customs~4 None
G_0~0, G_1~1, G_2~2, G_3~3, G_4~4, G_5~5,

G_6~6, G_7~7, G_8~8, G_9~9, G_10~10,
G_11~11, G_12~12, G_13~13, G_14~14,
G_15~15, G_16~16, G_17~17, G_18~18,
G_19~19, G_20~20, G_21~21, G_22~22,
G_23~23, G_24~24, G_25~25, G_26~26,
G_27~27, G_28~28, G_29~29, G_30~30, G_31~31 None
NOLIMIT~0, LIMIT~1 None
Not involved None
Not involved None
Not involved None
Not involved None

SUN~0, MON~1, TUE~2, WED~3, THU~4, FRI~5,
SAT~6 None
Not involved None

Administrators~0, Operators~1, Users~2, Guests~3,
Customs~4 None
Not involved None
Not involved None
INT~0, INTB~1, NAT~2, NATB~3 None
BIT14~14, BIT16~16, BIT24~24 None
WNF~0, DNF~1 None
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
ONE~1, TWO~2, THREE~3, FOUR~4 None
ATM~0, IP~1 None
UMTS~0 None
Not involved None
Not involved %
Not involved None

Not involved None
Not involved %
Not involved None
Not involved None
Not involved %
Not involved None
Not involved None
Not involved %
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None

AOUa~5, POUa~6, UOIa~7, AOUc~13, UOIc~15,
POUc~14 None
ALL~0, SINGLE~1 None
Not involved None
OFF~0, ON~1 None
SDH~0, SONET~1 None
LUCENT_MODE~0, HUAWEI_MODE~1,
ALCATEL_MODE~2 None
UNI~0, NNI~1 None
NULL~0, 1byte~1, 16byte~2, 64byte~3 None

Not involved None
Not involved None
Hexadecimal~0, Character_String~1 none
Not involved None
Not involved None
Not involved None
O1E3_R1E4~0, O1E4_R1E5~1, O1E5_R1E6~2,

O1E6_R1E7~3, O1E7_R1E8~4, O1E8_R1E9~5,
O1E9_R1E10~6, O1E10_R1E11~7,
O1E11_R1E12~8 None
O1E3_R1E4~0, O1E4_R1E5~1, O1E5_R1E6~2,
O1E6_R1E7~3, O1E7_R1E8~4, O1E8_R1E9~5,
O1E9_R1E10~6, O1E10_R1E11~7,
O1E11_R1E12~8 None
O1E3_R1E4~0, O1E4_R1E5~1, O1E5_R1E6~2,

O1E6_R1E7~3, O1E7_R1E8~4, O1E8_R1E9~5,
O1E9_R1E10~6, O1E10_R1E11~7 None
O1E3_R1E4~0, O1E4_R1E5~1, O1E5_R1E6~2,

O1E6_R1E7~3, O1E7_R1E8~4, O1E8_R1E9~5,
O1E9_R1E10~6, O1E10_R1E11~7 None
OFF~0, ON~1 None
Not involved None
ZERO~0, SPACE~1 None
AU4~0, AU3~1 None
Not involved None
Not involved None

Not involved None
NO_LOOP~2, LOCAL_LOOP~1,
REMOTE_LOOP~0 None
One_touch~0, Step_by_Step~1, )** None

SCUa~80, SCUb~113, GCUa~82, GCGa~83,
PEUa~1, AEUa~2, FG2a~3, GOUa~4, AOUa~5,
POUa~6, UOIa~7, AOUc~13, POUc~14, UOIc~15,
FG2c~17, GOUc~18, SPUa~48, SPUb~50,
DPUb~65, DPUe~69, NIUa~72 None
UCP~6, RUCP~8, UUP~13, ATM~20, IP~21,

NIU~38 None
MAINCPU_PATCH~65, DSP_PATCH~68,
UCODE_PATCH~99 None
Not involved None
Not involved None

BE~0, AF11~1, AF12~2, AF13~3, AF21~4,
AF22~5, AF23~6, AF31~7, AF32~8, AF33~9,
AF41~10, AF42~11, AF43~12, EF~13 None
Not involved None
Not involved None
IP~1, ATM~2 None
Not involved None
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved None
Not involved None
PEUa~1, POUa~6, UOIa~7, POUc~14 None
IP~21 None
Not involved None
Not involved None

TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,
TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
NO~0, YES~1 None
Not involved None
Not involved None
Not involved None
Not involved None
No_HC~3, UDP/IP_HC~1, RTP/UDP/IP_HC~0 None

Not involved byte
Not involved byte
Not involved ls
NO_V~0, PAP_V~1, CHAP_V~2 None
Not involved None
Not involved None
Not involved s
Not involved s
OFF~0, ON~1 None
Not involved %
Not involved None
None~0, 16bit~1, 32bit~2 None
Not involved None
OFF~0, ON~1 None
O1E3_R5E4~0, O5E4_R1E4~1, O1E4_R5E5~2,

OFF~0, ON~1 None
Not involved None
Not involved ls
Not involved None
Not involved None

PPP~5, MPGRP~7 None
Not involved None

Not involved None
NO_LOOP~0, SELF_LOOP~1 None
Not involved min
Not involved None

LOWERCASE~0, UPPERCASE~1, DIGIT~2,
SPECHAR~3 None
Not involved None
Not involved min
Not involved min
Not involved d
Not involved d
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None

BIT0~0, BIT1~1, BIT6~6, BIT7~7, BIT8~8, BIT9~9,
BIT14~14, BIT15~15, BIT16~16, BIT17~17,
BIT22~22, BIT23~23, BIT24~24, BIT25~25,
BIT29~29, BIT30~30, BIT31~31 None
BIT0~0, BIT1~1, BIT2~2, BIT3~3, BIT4~4, BIT5~5,

BIT6~6, BIT7~7, BIT8~8, BIT9~9, BIT10~10,
BIT11~11, BIT12~12 None
Not involved None
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved V
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
OFF~0, ON~1 None
SINGLE~0, ALL~1 None
Not involved None
Not involved None

Not involved None
ASC0~0, ASC1~1, ASC2~2, ASC3~3, ASC4~4,
ASC5~5, ASC6~6, ASC7~7 None
Not involved None
Not involved None
Not involved None
ATM~0, IP~1 None
NO~0, YES~1 None
Not involved None
Not involved None
FULL_DUPLEX~0, HALF_DUPLEX~1 None
Not involved kbit/s

Not involved kbit/s
Not involved kbit/s
Not involved None
Not involved None
Not involved None
Not involved None
UNI~3, IMA~4, FRAATM~5, NCOPT~6,

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
UNI~0, NNI~1 None
MPS_EMERGENCY~1, MPS_NORMAL~2,
MPS_NEUTRAL~3 None
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved s
Not involved s
Not involved ms
Not involved min
Not involved ms
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved None
Not involved None
Not involved None
Not involved None
DISABLED~0, ENABLED~1 None
Not involved None
Not involved None
Not involved dB
Not involved None
Not involved None
Not involved None
NBAP~0, M3UA~1 None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
NO~0, YES~1 None
Not involved None
Not involved None
Not involved ms
Not involved ms
Not involved ms
Not involved %
Not involved %
Not involved ms
Not involved ms
Not involved None
Not involved None
NO~0, YES~1 None
NO~0, YES~1 None
ALDER32~0, CRC32~1 None
Not involved None
Not involved None
Not involved None
UNAVAILABLE~0, AVAILABLE~1 None
NO~0, YES~1 None
Not involved None
NO~0, YES~1 None
Not involved ms
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
XPU~3 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
ON~0, OFF~1 None
ON~0, OFF~1 None
ON~0, OFF~1 None
ON~0, OFF~1 None
Not involved min
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
NONE~0, PEER~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
NO~0, YES~1 None
SCUa~80, SCUb~113 None
PARC~1, PARCb~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
ONTIME~0, DAILY_T~1, DAILY_C~2,

WEEKLY_T~3, WEEKLY_C~4, MONTHLY_T~5,
MONTHLY_C~6 None
Not involved None
Not involved None
Not involved None

MON_1~1, MON_2~2, MON_3~3, MON_4~4,
MON_5~5, MON_6~6, MON_7~7, MON_8~8,
MON_9~9, MON_10~10, MON_11~11,
MON_12~12, MON_13~13, MON_14~14,
MON_15~15, MON_16~16, MON_17~17,
MON_18~18, MON_19~19, MON_20~20,
MON_21~21, MON_22~22, MON_23~23,
MON_24~24, MON_25~25, MON_26~26,
MON_27~27, MON_28~28, MON_29~29,
MON_30~30, MON_31~31 None
SAT~6 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None

ATM~0, IP~1 None
PERCENTAGE~0, BANDWIDTH~1 None
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s

Not involved kbit/s
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved None
CBR~0, RT_VBR~1, NRT_VBR~2, UBR~3, BE~4,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
LQAF41~28, LQAF42~29, LQAF43~30, LQEF~31 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
LQAF41~28, LQAF42~29, LQAF43~30, LQEF~31,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,

AF11~5, AF12~6, AF13~7, AF21~8, AF22~9,
AF23~10, AF31~11, AF32~12, AF33~13, AF41~14,
AF42~15, AF43~16, EF~17, LQBE~18,
LQAF11~19, LQAF12~20, LQAF13~21,
LQAF21~22, LQAF22~23, LQAF23~24,
LQAF31~25, LQAF32~26, LQAF33~27,
NULL~255 None
Not involved None
Not involved None
Not involved None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
Not involved None
TS1~1, TS2~2, TS3~3, TS4~4, TS5~5, TS6~6,

TS7~7, TS8~8, TS9~9, TS10~10, TS11~11,
TS12~12, TS13~13, TS14~14, TS15~15, TS16~16,
TS17~17, TS18~18, TS19~19, TS20~20, TS21~21,
TS22~22, TS23~23, TS24~24, TS25~25, TS26~26,
TS27~27, TS28~28, TS29~29, TS30~30, TS31~31 None
Not involved None

GMT-1200~0, GMT-1100~4, GMT-1000~8, GMT-
0930~10, GMT-0900~12, GMT-0800~16, GMT-
0700~20, GMT-0600~24, GMT-0500~28, GMT-
0430~30, GMT-0400~32, GMT-0330~34, GMT-
0300~36, GMT-0200~40, GMT-0100~44, GMT~48,
GMT+0100~52, GMT+0200~56, GMT+0300~60,
GMT+0330~62, GMT+0400~64, GMT+0430~66,
GMT+0500~68, GMT+0530~70, GMT+0545~71,
GMT+0600~72, GMT+0630~74, GMT+0700~76,
GMT+0800~80, GMT+0845~83, GMT+0900~84,
GMT+0930~86, GMT+1000~88, GMT+1030~90,
GMT+1100~92, GMT+1130~94, GMT+1200~96,
GMT+1245~99, GMT+1300~100, GMT+1400~104 None
NO~0, YES~1 None
DATE~0, WEEK~1, DATEWEEK~2 None
JAN~1, FEB~2, MAR~3, APR~4, MAY~5, JUN~6,

JUL~7, AUG~8, SEP~9, OCT~10, NOV~11,
DEC~12 None
Not involved d
FIRST~1, SECOND~2, THIRD~3, FOURTH~4,
LAST~0 None
SAT~6 None
Not involved None
DATE~0, WEEK~1, DATEWEEK~2 None
JAN~1, FEB~2, MAR~3, APR~4, MAY~5, JUN~6,

JUL~7, AUG~8, SEP~9, OCT~10, NOV~11,
DEC~12 None
Not involved d
FIRST~1, SECOND~2, THIRD~3, FOURTH~4,
LAST~0 None
SAT~6 None
Not involved None
Not involved min
Not involved None
Not involved None
Not involved None

Not involved dB
Not involved dB
Not involved dBm
D0~1, D10~2, D20~3, D30~4, D40~5, D50~6,

D60~7 s
D3~0, D6~1, D9~2, D12~3, D15~4, D18~5, D21~6,

INFINITY~7 dB
FALSE~0, TRUE~1 None
Not involved None
Not involved dB
Not involved None

Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved %
Not involved ms
Not involved s
Not involved s
NOPRIORITY~0, GOLD~1, SILVER~2, COPPER~3 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
TRUE~0, FALSE~1 None
Not involved None
Not involved dB
Not involved %
Not involved %
Not involved %
Not involved %
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved ms
Not involved ms
NBAMR_BITRATE_4.75K~1,
NBAMR_BITRATE_12.20K~8 kbit/s
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved ms
Not involved ms
WBAMR_BITRATE_6.60K~1,
WBAMR_BITRATE_23.85K~9 kbit/s
Not involved None
Not involved None
OFF~0, ON~1 None

OFF~0, ON~1 None
Band1~0, Band2~1, Band3~2, Band4~3, Band5~4,

Band6~5, Band7~6, Band8~7, Band9~8 None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None

Not involved None

Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
GSM900_DCS1800_BAND_USED~0,
PCS1900_BAND_USED~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
NODEB_CREDIT_CAC_SWITCH~0 None
RSVDBIT1~0, RSVDBIT2~1, RSVDBIT3~2,
RSVDBIT16~15 None
Not involved None
Not involved None
SYS_LEVEL~0, NODEB_LEVEL~1,
CELL_LEVEL~2 None
OFF~0, ON~1 None
Not involved s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None

MBR~0
Category~1
Min~2
Max~3 None
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s

MBR~0
Category~1
Min~2
Max~3 None
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s

Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
LAC~0, RNC~1, CELL~2 None
Not involved None
Not involved None

Not involved None
Not involved None

Not involved None
CellImmediate~0, PLMNNormal~1, SANormal~2,

CellNormal~3 None
High~0, Background~1, Normal~2, Default~3,
Butt~4 None
Not involved s
Not involved None

English~1, Italian~2, French~3, Spanish~4,
Dutch~5, Swedish~6, Danish~7, Portuguese~8,
Finnish~9, Norwegian~10, Greek~11, Turkish~12,
Hungarian~13, Polish~14, UCS2~72 None
Not involved None
Earthquake~0, Tsunami~1, Hurricane~2, Other~3 None

Not involved None
Not involved None
Not involved None
Not involved None
SAAL~0, SCTP~1, SAAL-SCTP~2 None
Not involved None
Not involved None
SAAL~0, SCTP~1 None
ATMTODUAL~0, IPTODUAL~1, DUALTOATM~2,

DUALTOIP~3 None
SAAL~0, SCTP~1 None
FIXED~0, CYCLE~1 None

Not involved min
Not involved None
Not involved None

Not involved dBm

Band6~5, Band7~6, Band8~7, Band9~8,
BandIndNotUsed~255 None
INVALID~0, VALID~1 None
Not involved None
Not involved None

Not involved None
Not involved None
CHIP0~0, CHIP256~1, CHIP512~2, CHIP768~3,

CHIP1024~4, CHIP1280~5, CHIP1536~6,
CHIP1792~7, CHIP2048~8, CHIP2304~9 chip
Not involved None
Not involved None
Not involved s
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
NOT_REQUIRE~0, REQUIRE~1 None
Not involved None
STTD_Supported~0, STTD_not_Supported~1 None
CP1_Supported~0, CP1_not_Supported~1 None
OFFSET1~0, OFFSET2~1 None
None~0, STTD~1, CP1~2 None
None~0, STTD~1 None
None~0, STTD~1 None
None~0, STTD~1 None

Not involved dB
Not involved dBm
Not involved None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None
RESERVED~0, NOT_RESERVED~1 None
BARRED~0, NOT_BARRED~1 None

ALLOWED~0, NOT_ALLOWED~1 None
D10~0, D20~1, D40~2, D80~3, D160~4, D320~5,

D640~6, D1280~7 s
ALLOWED~0, NOT_ALLOWED~1 None
D10~0, D20~1, D40~2, D80~3, D160~4, D320~5,

D640~6, D1280~7 s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

CRD_ADCTRL~0, HSDPA_UU_ADCTRL~1,
HSUPA_UU_ADCTRL~2, MBMS_UU_ADCTRL~3,
HSDPA_GBP_MEAS~4, HSDPA_PBR_MEAS~5,
HSUPA_PBR_MEAS~7,
HSUPA_EDCH_RSEPS_MEAS~8,
EMC_UU_ADCTRL~9,
RTWP_RESIST_DISTURB~10,
FACH_UU_ADCTRL~12,
MIMOCELL_LEGACYHSDPA_ADCTRL~13,
FAST_DORMANCY_ADCTRL~14 None
ALGORITHM_OFF~0, ALGORITHM_FIRST~1,
ALGORITHM_SECOND~2, ALGORITHM_THIRD~3 None
ALGORITHM_OFF~0, ALGORITHM_FIRST~1,
ALGORITHM_SECOND~2, ALGORITHM_THIRD~3 None
INTRA_FREQUENCY_LDB~0, PUC~1,
UL_UU_LDR~2, DL_UU_LDR~3, UL_UU_OLC~4,
DL_UU_OLC~5, OLC_EVENTMEAS~6,
CELL_CODE_LDR~7, CELL_CREDIT_LDR~8,
UL_INTRA_FREQUENCY_ULB~9 None
ALGORITHM_REQUIRED~0,
ALGORITHM_DEPEND_ON_LCG~1 None
64QAM~0, MIMO~1, E_FACH~2, DTX_DRX~3,
HS_SCCH_LESS_OPERATION~4,
DL_L2ENHANCED~5, 64QAM_MIMO~6,
UL_16QAM~7, DC_HSDPA~8,
UL_L2ENHANCED~9, EDPCCH_BOOSTING~10,
DCMIMO_HSDPA~11, E_DRX~12 None
E_F_DPCH_OFF~0, E_F_DPCH_ON~1 None
TX_DIVERSITY_ON_TO_OFF~0,
TX_DIVERSITY_OFF_TO_ON~1 None
NBM_LDC_ALL_UE~0,
NBM_LDC_MATCH_UE_ONLY~1,
NBM_LDC_MATCH_UE_FIRST~2 None

RSVDBIT16~15 None
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None

Not involved None
Not involved None
Not involved None
TU~0, RA~1, HT~2 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None

Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dB
OFF~0, ON~1 None
Not involved s
Not involved None
Not involved None
Not involved %
Not involved %
Not involved %
Not involved None
Not involved %
Not involved None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,

SF128~5, SF256~6, SFOFF~7 None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,

SF128~5, SF256~6, SFOFF~7 None
Not involved None
Not involved None
Not involved dBm
Not involved dB
Not involved None
Not involved %
Not involved None
Not involved None
Not involved %
Not involved %
Not involved None
Not involved None
Not involved None

Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
WALKING_SPEED_AND_HOT_SPOT_CELL~0,
MID_SPEED_AND_HOT_SPOT_CELL~1,
HIGH_SPEED_AND_HOT_SPOT_CELL~2,
LOW_SPEED_AND_MEDIUM_COVERAGE_CELL
~3,
HIGH_SPEED_AND_MEDIUM_COVERAGE_CELL
~4,
LOW_SPEED_AND_HIGH_COVERAGE_CELL~5,
HIGH_SPEED_AND_HIGH_COVERAGE_CELL~6,
OTHER_CELL~7 None
D8~1, D16~2, D32~3, D64~4, D128~5, D256~6 None
D8~1, D16~2, D32~3, D64~4, D128~5, D256~6 None
Not involved None
Not involved dB
Not involved dB
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
Not involved None
OFF~0, ON~1 None
Not involved chip
Not involved %
Not involved %
Not involved None
Not involved None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
Power~1, UserNumber~0 None
Not involved %
Not involved %
ON~1, OFF~0 None

SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,
SF128~5, SF256~6 None
Not involved %
DependOnNCell~254, BandIndNotUsed~255 None

Not involved None
Not involved None
ON~1, OFF~0 None
Not involved %
ON~1, OFF~0 None
Not involved None
ON~1, OFF~0 None
ON~1, OFF~0 None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
RestrictionFixed~0, RestrictionFlexible~1 None

AC0~0, AC1~1, AC2~2, AC3~3, AC4~4, AC5~5,
AC6~6, AC7~7, AC8~8, AC9~9, AC10~10,
AC11~11, AC12~12, AC13~13, AC14~14,
AC15~15 None
Not involved None
AC0~0, AC1~1, AC2~2, AC3~3, AC4~4, AC5~5,

AC6~6, AC7~7, AC8~8, AC9~9, AC10~10,
AC11~11, AC12~12, AC13~13, AC14~14,
AC15~15 None
Not involved s
Not involved None
OFF~0, ON_1~1, ON_2~2, ON_3~3 None

Not involved min
Not involved min
Not involved min
Not involved min
Not involved min
Not involved min
FORCESHUTDOWN~0,
CONDITIONALSHUTDOWN~1,
QOSSHUTDOWN~2 None
Not involved None
Not involved None
Not involved None
Not involved %
SPI1~1, SPI2~2, SPI3~3, SPI4~4, SPI5~5, SPI6~6,
SPI7~7, SPI8~8, SPI9~9, SPI10~10, SPI11~11,
SPI12~12, SPI13~13, SPI14~14, SPI15~15 None
Not involved None
EDRXT321_100~0, EDRXT321_200~1,
EDRXT321_400~2, EDRXT321_800~3 ms
EDRXCYCLE_4~0, EDRXCYCLE_8~1,
EDRXCYCLE_16~2, EDRXCYCLE_32~3 frame
EDRXBURST_1~0, EDRXBURST_2~1,
EDRXBURST_4~2, EDRXBURST_8~3,
EDRXBURST_16~4 frame
INTERRUPTION_CFG~0,
INTERRUPTION_NOT_CFG~1 None
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s

Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved dB
Not involved None
Not involved ms
Not involved ms
Not involved kbit/s
Not involved None
D8~1, D16~2 kbit/s
D8~1, D16~2 kbit/s
Not involved dB
Not involved ms
Not involved None
Not involved None
Not involved None

Not involved None

Not involved None
Not involved None
INACTIVE~0, ACTIVE~1 None
Not involved None
USED~0, NOT_USED~1 None

Not involved None
Not involved dB
Not involved dB
Not involved dB/ dBm

NOT_USED~0, D30~1, D60~2, D120~3, D180~4,
D240~5 s
Not involved None
NOT_USED~0, D10~1, D20~2, D30~3, D40~4,

D50~5, D60~6, D70~7 s
Not involved dB
Not involved None
OFF~1, ON~0 None
Not involved s
Not involved None
Not involved s
Not involved s
Not involved None
Not involved s
Not involved None
INTERFREQ~0, INTERRAT~1,
SIMINTERFREQRAT~2 None
COEXIST_MEAS_THD_CHOICE_INTERFREQ~0,
COEXIST_MEAS_THD_CHOICE_INTERRAT~1 None
OFF~1, ON~0 None
OFF~1, ON~0 None
Not involved None
Manual~1, Automatic~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
Minus3.0DB~0, Minus2.5DB~1, Minus2.0DB~2,
0.0DB~6, 0.5DB~7, 1.0DB~8, 1.5DB~9, 2.0DB~10,
2.5DB~11, 3.0DB~12, 3.5DB~13, 4.0DB~14,
4.5DB~15, 5.0DB~16, 5.5DB~17, 6.0DB~18,
6.5DB~19, 7.0DB~20, 7.5DB~21, 8.0DB~22,
8.5DB~23, 9.0DB~24, 9.5DB~25, 10.0DB~26,
10.5DB~27, 11.0DB~28, 11.5DB~29, 12.0DB~30,
12.5DB~31, 13.0DB~32, 13.5DB~33, 14.0DB~34,
14.5DB~35, 15.0DB~36, 15.5DB~37, 16.0DB~38,
16.5DB~39, 17.0DB~40, 17.5DB~41, 18.0DB~42,
18.5DB~43, 19.0DB~44 dB
Mode0~0, Mode1~1 None
OFF~0, ON~1 None
Not involved None
Not involved s

0.0DB~6, 0.5DB~7, 1.0DB~8, 1.5DB~9, 2.0DB~10,
2.5DB~11, 3.0DB~12, 3.5DB~13, 4.0DB~14,
4.5DB~15, 5.0DB~16, 5.5DB~17, 6.0DB~18,
6.5DB~19, 7.0DB~20, 7.5DB~21, 8.0DB~22,
8.5DB~23, 9.0DB~24, 9.5DB~25, 10.0DB~26,
10.5DB~27, 11.0DB~28, 11.5DB~29, 12.0DB~30,
12.5DB~31, 13.0DB~32, 13.5DB~33, 14.0DB~34,
14.5DB~35, 15.0DB~36, 15.5DB~37, 16.0DB~38,
16.5DB~39, 17.0DB~40, 17.5DB~41, 18.0DB~42,
18.5DB~43, 19.0DB~44 dB
Not involved None
Not involved None

PO_5/15~0, PO_6/15~1, PO_8/15~2, PO_9/15~3,
PO_12/15~4, PO_15/15~5, PO_19/15~6,
PO_24/15~7, PO_30/15~8 None
PO_5/15~0, PO_6/15~1, PO_8/15~2, PO_9/15~3,
PO_12/15~4, PO_15/15~5, PO_19/15~6,
PO_24/15~7, PO_30/15~8 None
Not involved None
Not involved None

D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D4~2, D8~3, D10~4, D20~5, D40~6, D80~7,
D160~8 ms
Not involved None
Not involved None
Not involved None
Not involved %
Not involved %
Not involved None
Not involved None
Not involved None
Not involved None

PERIODICAL_REPORTING~0,
EVENT_TRIGGER~1 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
NON_PERIODIC_REPORT~0, D250~1, D500~2,

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms

Not involved None
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved ms
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm

Not involved dBm
Not involved s
Not involved ms
Not involved None
Not involved ms
Not involved None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dB
Not involved s
Not involved ms
Not involved None
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
CPICH_EC/NO~0, CPICH_RSCP~1, AUTO~2 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved None

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms
Not involved dB
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved ms
Not involved ms
REQUIRED~0, NOT_REQUIRE~1 None
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dBm

Not involved dB
Not involved dB
Not involved dB
Not involved dBm

Not involved dBm
Not involved dBm
Not involved s
Not involved s
Not involved dBm
Not involved ms
Not involved None
Not involved None
Not involved s
Not involved None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dBm

Not involved dBm
Not involved None
Not involved s
Not involved %
Not involved %
Not involved ms
Not involved None
Not involved None
Not involved s
Not involved None
Not involved None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
CPICH_EC/NO~0, CPICH_RSCP~1 None
D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,

INFINITY~7 None

D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,

INFINITY~7 None

D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,

INFINITY~7 None

D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dB
Not involved None
Not involved dBm
Not involved None
Not involved dB
Not involved %
Not involved %
Not involved None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved ms
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved None

NoAct~0, InterFreqLDHO~1, BERateRed~2,
QoSRenego~3, CSInterRatShouldBeLDHO~4,
PSInterRatShouldBeLDHO~5, AMRRateRed~6,
MBMSDecPower~7, CodeAdj~8,
CSInterRatShouldNotLDHO~9,
PSInterRatShouldNotLDHO~10 None







Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None






Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved %
Not involved %
Not involved bit/s
Not involved bit/s

Not involved None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,

SF128~5, SF256~6 None
Not involved None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,

SF128~5, SF256~6 None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,

SF128~5, SF256~6 None
Not involved %
OFF~0, ON~1 None
R99_CONVERSATIONAL~0, R99_STREAMING~1,
R99_BE~2, HSDPA_CONVERSATIONAL~3,
HSDPA_STREAMING~4, HSDPA_BE~5,
HSPA_CONVERSATIONAL~6,
HSPA_STREAMING~7, HSPA_BE~8 None
8SF4~0, 7SF4~1, 6SF4~2, 5SF4~3, 4SF4~4,

3SF4~5, 2SF4~6, SF4~7, SF8~8, SF16~9,
SF32~10, SF64~11, SF128~12, SF256~13 None
BLINDHO~0, MEASUREHO~1 None
Not involved None

INTELLIGENT_INTERFREQ_UE_TYPE_STEERIN
G~1 None
Not involved None
CSAMR_INTERFREQ~0,
CSNONAMR_INTERFREQ~1,
PSR99_INTERFREQ~2, PSHSPA_INTERFREQ~3 None
Not involved None
Not involved None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
CPICH_EC/NO~0, CPICH_RSCP~1, BOTH~2 None

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms
Not involved ms
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dB
Not involved dB
Not involved None

Not involved s
Not involved None
CSAMR_INTERRAT~0 None
Not involved None
Not involved None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms
Not involved ms
Not involved ms
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dBm
Not involved None

ALL_USER~0, HALF~1, THIRD~2, QUARTER~3 None
Not involved s
Not involved s
Not involved None
STREAMING~1, BACKGROUND~2 None
D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
Not involved dB
Not involved %
Not involved %
Not involved ms
Not involved ms
Not involved None
PTM~0, PTP~1, ENHANCEDPTM~2, DYNAMIC~3 None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
Not involved None

Not involved None
Not involved dB
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
OFF~0, ON~1 None
Not involved s
D250~1, D500~2, D1000~3, D2000~4, D3000~5,
D4000~6, D6000~7, D8000~8, D12000~9,
D16000~10, D20000~11, D24000~12, D28000~13,
D32000~14, D64000~15 ms
Not involved dBm
Not involved dB
Not involved None
Not involved None
Not involved s
D250~1, D500~2, D1000~3, D2000~4, D3000~5,
D4000~6, D6000~7, D8000~8, D12000~9,
D16000~10, D20000~11, D24000~12, D28000~13,
D32000~14, D64000~15 ms
Not involved dBm
Not involved dB
Not involved None
REQUIRE~0, NOT_REQUIRE~1 None
NOT_REQUIRE~1, INTER_FREQ~2,
INTER_RAT~3,
INTER_FREQ_AND_INTER_RAT~4
REQUIRE~0, NOT_REQUIRE~1, INTER_FREQ~2, None
INTER_RAT~3,
INTER_FREQ_AND_INTER_RAT~4 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved dB
Not involved dB
D6~0, D15~1, D25~2, D50~3, D75~4, D100~5 None
Not involved dBm
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D10~10, D11~11, D12~12,
D13~13, D14~14, D15~15, D16~16 None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved %
Not involved %
Not involved ms
Not involved ms
Not involved None
Not involved None
MBMS_REL~0, USER_REL~1 None
Not involved None
Not involved None
Not involved dB
Not involved None
Not involved %
Not involved %
Not involved %
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None
Not involved dB
Not involved s
Not involved s

Not involved None
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
TEN_MSEC~1, MIN~2 None
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min

Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min
Not involved None
AMR~0, VP~1, PSR99~2, PSHSPA~3 None
OFF~0, ONLY_TO_INTER_FREQUENCY~1,
ONLY_TO_INTER_RAT~2 None
Not involved %
Not involved %

Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
CS_DOMAIN~0, PS_DOMAIN~1 None
Not involved bit/s
Not involved dB
Not involved dB
D4~4, D8~8, D16~16, D32~32, D64~64, D128~128,
D256~256, D512~512 None
Not involved None
CPICH_ECNO~1, CPICH_RSCP~2 None
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved s
Not involved dB
Not involved dBm
Not involved None
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None
Not involved None
Not involved None
CONFIGURED~0, NOT_CONFIGURED~1 None

NotUsed~1, D30~2, D60~3, D120~4, D180~5,
D240~6 s
Not involved None
NotUsed~0, D10~1, D20~2, D30~3, D40~4, D50~5,

D60~6, D70~7 s
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved s
Not involved s
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved None
SIB2~1, SIB4~3, SIB12~11, SIB18~17, SIB19~18,

SIB11BIS~20 None
Not involved None
MeasurementQuantity~0, Both~1 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved s
RSRP~0, RSRQ~1 None

Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dBm
Not involved dB
Not involved None
Not involved %
Not involved %
Not involved dB
Not involved None

Not involved None
Not involved None
Not involved byte
Not involved None
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved dB
ABNORMAL_ONLY~0, NORMAL_ONLY~1 None
CS_ONLY~0, PS_ONLY~1 None

CONN_SETUP~0, RAB~1, DCCC~2, SHO~3,
HHO~4, SYS_HO_OUT~5, RRC_RELEASE~6,
STAT~7, NET_OPT~8 None
ORIGINATING_CONVERSATIONAL_CALL~0,
ORIGINATING_STREAMING_CALL~1,
ORIGINATING_INTERACTIVE_CALL~2,
ORIGINATING_BACKGROUND_CALL~3,
ORIGINATING_SUBSCRIBED_TRAFFIC_CALL~4,
TERMNT_CONVERSATIONAL_CALL~5,
TERMNT_STREAMING_CALL~6,
TERMNT_INTERACTIVE_CALL~7,
TERMNT_BACKGROUND_CALL~8,
EMERGENCY_CALL~9,
INTER_RAT_CELL_RESELECTION~10,
INTER_RAT_CELL_CHG_ORDER~11,
REGISTRATION~12, DETACH~13,
ORIGINATING_HIGH_PRIOR_SIG~14,
ORIGINATING_LOW_PRIOR_SIG~15,
CALL_RE_ESTAB~16,
TERMNT_HIGH_PRIOR_SIG~17,
TERMNT_LOW_PRIOR_SIG~18,
TERMNT_CAUSE_UNKNOWN~19,
MBMS_RECEPTION~20,
MBMS_PTP_RB_REQ~21 None
ByRack~0, ByNodeBId~1, ByCellId~2 None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved d
Not involved frame
D8~1, D16~2, D32~3, D64~4, D128~5, D256~6 None
D8~1, D16~2, D32~3, D64~4, D128~5, D256~6 None
WALKING_SPEED_AND_HOT_SPOT_CELL~0,
MID_SPEED_AND_HOT_SPOT_CELL~1,
HIGH_SPEED_AND_HOT_SPOT_CELL~2,
LOW_SPEED_AND_MEDIUM_COVERAGE_CELL
~3,
HIGH_SPEED_AND_MEDIUM_COVERAGE_CELL
~4,
LOW_SPEED_AND_HIGH_COVERAGE_CELL~5,
HIGH_SPEED_AND_HIGH_COVERAGE_CELL~6,
OTHER_CELL~7 None
D8~1, D16~2, D32~3, D64~4, D128~5, D256~6 None

Limited~0, Permit~1, BasedOnUECap~2 None
Not involved min
NOT_ALLOWED~0, ALLOWED~1 None
MODE1~0, MODE2~1 None
Not involved None

Not involved None
Not involved None
Not involved None
R99~0, R4~1, R5~2, R6~3, R7~4, R8~5 None
CR527_SUPPORT~1, CR527_NOT_SUPPORT~0,
CR528_SUPPORT~3, CR528_NOT_SUPPORT~2,
CR529_SUPPORT~5, CR529_NOT_SUPPORT~4 None
NORMAL~0, OFFLOAD~1, INHIBITED~2 None
Not involved None

ATM_TRANS~0, IP_TRANS~1 None
OFF~1, ON~0 None
Not involved None
OFF~0, ON~1 None
RSVDBIT1_BIT1~0, RSVDBIT1_BIT2~1,
RSVDBIT1_BIT31~30, RSVDBIT1_BIT32~31 None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
PsBlk~0, CsAndPsBlk~1 None

Not involved min
PRIM~0, SEC~1, OUTER~2, COMM~3 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
ON~0, OFF~1 None
Not involved None
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
D100~0, D200~1, D400~2, D600~3, D800~4,

D1000~5, D1200~6, D1400~7, D1600~8, D1800~9,
D2000~10, D3000~11, D4000~12, D6000~13,
D8000~14 ms
Not involved None
D100~0, D200~1, D400~2, D1000~3, D2000~4 ms
Not involved None

INFINITY~0, D5~1, D10~2, D30~3, D60~4,
D120~5, D360~6, D720~7 None
D5~0, D10~1, D15~2, D20~3, D30~4, D40~5,
D50~6 s
D40~0, D80~1, D160~2, D320~3 ms
Not involved None
Not involved s
Not involved s
D1~0, D2~8, D4~9, D10~10, D20~11, D50~1,
D100~2, D200~3, D400~4, D600~5, D800~6,
D1000~7 None
Not involved s
D1~0, D2~1, D4~2, D10~3, D20~4, D50~5,
D100~6, D200~7 None
D0~0, D2~1, D4~2, D6~3, D8~4, D12~5, D16~6,
D20~7 s
D0~0, D10~1, D30~2, D60~3, D180~4, D600~5,

D1200~6, D1800~7 s
D1~0, D2~8, D4~9, D10~10, D20~11, D50~1,
D100~2, D200~3, D400~4, D600~5, D800~6,
D1000~7 None
D0~0, D10~1, D20~2, D30~3, D40~4, D50~5,
INFINITY~6 s
D0~0, D100~1, D200~2, D300~3, D400~4, D500~5,
D600~6, D700~7, D800~8, D900~9, D1000~10,
D1200~11, D1500~12, D2000~13 ms
D1~0, D2~1, D3~2, D4~3 None

D0~0, D5~1, D10~2, D20~3, D30~4, D60~5,
D90~6, D120~7, INVALID~255 s
CFG_DL_BLIND_DETECTION_SWITCH~0,
CFG_HSDPA_64QAM_SWITCH~1,
CFG_HSDPA_DC_SWITCH~13,
CFG_HSDPA_MIMO_SWITCH~2,
CFG_HSDPA_MIMO_WITH_64QAM_SWITCH~12,
CFG_HSPA_DTX_DRX_SWITCH~3,
CFG_HSPA_HSSCCH_LESS_OP_SWITCH~4,
CFG_HSUPA_16QAM_SWITCH~14,
CFG_IMS_SUPPORT_SWITCH~5,
CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITC
H~6, CFG_LOSSLESS_RELOC_CFG_SWITCH~7,
CFG_MULTI_RAB_SWITCH~8,
CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH~
9, CFG_PDCP_RFC2507_HC_SWITCH~10,
CFG_PDCP_RFC3095_HC_SWITCH~11,
CFG_PTT_SWITCH~16,
CFG_RAB_REL_RMV_HSPAPLUS_SWITCH~15,
CFG_EDPCCH_BOOSTING_SWITCH~17,
CFG_HSDPA_DCMIMO_SWITCH~18,
CFG_FREE_USER_SWITCH~19,
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH~2
0 None
DRA_AQM_SWITCH~0,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH
~20,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH~
19,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH~
16,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH~1
5,
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH~18,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH~17,
DRA_DCCC_SWITCH~3,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH~4,
DRA_HSDPA_STATE_TRANS_SWITCH~5,
DRA_HSUPA_DCCC_SWITCH~6,
DRA_HSUPA_STATE_TRANS_SWITCH~7,
DRA_IP_SERVICE_QOS_SWITCH~21,
DRA_PS_BE_STATE_TRANS_SWITCH~9,
DRA_PS_NON_BE_STATE_TRANS_SWITCH~10,
DRA_R99_DL_FLOW_CONTROL_SWITCH~11,
DRA_THROUGHPUT_DCCC_SWITCH~12,
DRA_VOICE_SAVE_CE_SWITCH~13,
DRA_VOICE_TTI_RECFG_SWITCH~14 None
CS_AMRC_SWITCH~0,
CS_HANDOVER_TO_UTRAN_DEFAULT_CFG_S
WITCH~1, CS_IUUP_V2_SUPPORT_SWITCH~2 None
PC_CFG_ED_POWER_INTERPOLATION_SWITC
H~12,
PC_DL_INNER_LOOP_PC_ACTIVE_SWITCH~1,
PC_DOWNLINK_POWER_BALANCE_SWITCH~2,
PC_EFACH_ECN0_DYN_ADJ_SWITCH~3,
PC_FP_MULTI_RLS_IND_SWITCH~4,
PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH~
13,
PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWI
TCH~14,
PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITC
H~5,
PC_INNER_LOOP_LMTED_PWR_INC_SWITCH~7
, PC_OLPC_SWITCH~8,
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH
~9, PC_SIG_DCH_OLPC_SWITCH~10,
PC_UL_SIRERR_HIGH_REL_UE_SWITCH~11 None
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH
~0,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWI
TCH~12,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH
~1,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWIT
CH~2, CMP_IUR_SHO_DIVCTRL_SWITCH~3,
CMP_UU_ADJACENT_FREQ_CM_SWITCH~5,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH~1
1, CMP_UU_AMR_SID_MUST_CFG_SWITCH~4,
CMP_UU_FDPCH_COMPAT_SWITCH~10,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH~6,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_S
WITCH~15,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWI
TCH~14,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITC
H~7,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_S
WITCH~8,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_S
WITCH~9,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH~1
7,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH~1
8, CMP_RAB_5_CFG_ROHC_SWITCH~25,
CMP_RAB_6_CFG_ROHC_SWITCH~26,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH~30,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH~31 None
MAP_HSUPA_TTI_2MS_SWITCH~0,
MAP_INTER_RAT_PS_IN_CHANLE_LIMIT_SWIT
CH~1, MAP_PS_BE_ON_E_FACH_SWITCH~2,
MAP_PS_STREAM_ON_E_FACH_SWITCH~3,
MAP_PS_STREAM_ON_HSDPA_SWITCH~4,
MAP_PS_STREAM_ON_HSUPA_SWITCH~5,
MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWI
TCH~6,
MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWIT
CH~7 None
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH~
0,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH~1,
PS_BE_IU_QOS_NEG_SWITCH~2,
PS_RAB_DOWNSIZING_SWITCH~3,
PS_STREAM_IU_QOS_NEG_SWITCH~5,
PS_BE_STRICT_IU_QOS_NEG_SWITCH~6 None
DR_RRC_DRD_SWITCH~0,
DR_RAB_SING_DRD_SWITCH~1,
DR_RAB_COMB_DRD_SWITCH~2,
DR_INTER_RAT_DRD_SWITCH~3 None
HO_ALGO_HCS_SPEED_EST_SWITCH~0,
HO_ALGO_LDR_ALLOW_SHO_SWITCH~1,
HO_ALGO_MBMS_FLC_SWITCH~2,
HO_ALGO_OVERLAY_SWITCH~3,
HO_INTER_FREQ_HARD_HO_SWITCH~4,
HO_INTER_RAT_CS_OUT_SWITCH~6,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_S
WITCH~7,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWIT
CH~8, HO_INTER_RAT_PS_OUT_SWITCH~9,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH~1
0,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWI
TCH~11,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH~12,
HO_INTRA_FREQ_HARD_HO_SWITCH~13,
HO_INTRA_FREQ_RPRT_1J_SWITCH~14,
HO_INTRA_FREQ_SOFT_HO_SWITCH~16,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH~17,
HO_MC_NCELL_COMBINE_SWITCH~18,
HO_MC_SIGNAL_IUR_INTRA_SWITCH~19,
HO_MC_SIGNAL_SWITCH~20,
HO_MC_SNA_RESTRICTION_SWITCH~21,
HO_LTE_PS_OUT_SWITCH~22,
HO_LTE_SERVICE_PS_OUT_SWITCH~23,
HO_H2G_SRVCC_SWITCH~24 None
SRNSR_DSCR_IUR_RESRCE_SWITCH~0,
SRNSR_DSCR_LOC_SEPRAT_SWITCH~1,
SRNSR_DSCR_PROPG_DELAY_SWITCH~2,
SRNSR_DSCR_SEPRAT_DUR_SWITCH~3 None
CMCF_DL_HLS_SWITCH~0,
CMCF_UL_HLS_SWITCH~1,
CMCF_UL_PRECFG_TOLERANCE_SWITCH~2,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH~3 None
RESERVED_SWITCH_0_BIT1~0,
RESERVED_SWITCH_0_BIT32~31 None
Not involved None
Not involved None
Not involved None
Not involved None

CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH~0,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWIT
CH~1, CMP_IUR_CMCF_SWITCH~2,
CMP_STTD_RL_ADD_SWITCH~3,
CMP_STTD_ASU_SWITCH~4,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH~
5, CMP_WBAMR_SUBFLOW_SWITCH~7,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SW
ITCH~8, CMP_MOCN_PLMN_SEL_SWITCH~9,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_S
WITCH~10,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWIT
CH~11 None
PERFENH_AMR_SPEC_BR_SWITCH~0,
PERFENH_AMR_TMPLT_SWITCH~1,
PERFENH_SRB_TMPLT_SWITCH~2,
PERFENH_OLPC_TMPLT_SWITCH~3,
PERFENH_AMR_SP_TMPLT_SWITCH~4,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH~5,
PERFENH_INTERRAT_PENALTY_50_SWITCH~6,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH~
7,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH~8,
PERFENH_UU_P2D_CUC_OPT_SWITCH~9,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITC
H~10,
PERFENH_RRC_REDIR_PROTECT_SWITCH~11 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved %
Not involved None
Not involved None
RAN_CTRLPLN_FC~0 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D0~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D144~6, D256~7, D384~8 kbit/s
RATE_UP_AND_DOWN_ON_DCH~0,
RATE_UP_ONLY_ON_DCH~1 None
RATE_UP_AND_DOWN_ON_EDCH~0,
RATE_UP_ONLY_ON_EDCH~1 None
Not involved dB
Not involved dB
2_Rates~1, 3_Rates~2 None
AUTO_CALC~0, HAND_APPOINT~1 None

D16~2, D32~3, D64~4, D128~5, D144~6, D256~7,
D384~8 kbit/s
AUTO_CALC~0, HAND_APPOINT~1 None

D16~2, D32~3, D64~4, D128~5, D144~6, D256~7,
D384~8 kbit/s
Not involved None
Not involved s
Not involved s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
Not involved ms
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D608~10, D1280~13, D2048~16,
D2720~17, D5440~19, D11480~23 kbit/s
Not involved kbit/s
Not involved None
MultiIMSI~1, SingleIMSI~0 None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved chip
Not involved %
Not involved %
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
OFF~0, ON~1 None
Not involved %
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved %
Not involved None
OFF~0, ON~1 None
Not involved ms
Not involved %
Not involved None
Not involved None
TPE_DOWNLINK_SWITCH~0,
TPE_UPLINK_SWITCH~1 None
Not involved s
Not involved %
Not involved %
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
Qos~0, Spi~1, QosAndSpi~2, BothOFF~3 None

Not involved None
Not involved None
Not involved %
Not involved %
Not involved %
Not involved s
Not involved s
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved %
RsvdSwitch1_Bit1~0, RsvdSwitch1_Bit2~1,
RsvdSwitch1_Bit31~30, RsvdSwitch1_Bit32~31 None
RsvdSwitch2_Bit31~30, RsvdSwitch2_Bit32~31 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
UserNumber~0, Power~1 None
OFF~0, Only_To_Inter_Frequency~1,
Allowed_To_Inter_RAT~2 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
ON~1, OFF~0 None
Not involved %
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,
SF128~5, SF256~6 None
Not involved %
Not involved None

Not involved None
ON~1, OFF~0 None
Not involved %
Not involved %
OFF~0, ON~1 None

ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min
OFF~0, ON~1 None
Not involved None

AC0~0, AC1~1, AC2~2, AC3~3, AC4~4, AC5~5,
AC6~6, AC7~7, AC8~8, AC9~9, AC10~10,
AC11~11, AC12~12, AC13~13, AC14~14,
AC15~15 None
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
CONVERSATIONAL~0, STREAMING~1,
INTERACTIVE~2, BACKGROUND~3, NBAMR~4,
WBAMR~5 None
EDCH_10MS~0, EDCH_2MS~1 None
ON~1, OFF~0 None

D1~0, D4~1, D8~2, D16~3, D32~4, D64~5,
D128~6, D256~7 None
D2~0, D4~1, D15~2 slot

D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,
D128~7, D256~8, D512~9, INFINITY~10 None
D0~0, D1~1, D2~2, D4~3, D8~4, D16~5, D32~6,
D64~7, D128~8, D256~9, D512~10, INFINITY~11 None
D1~0, D2~1, D5~2 None
D1~0, D2~1, D5~2 None
ON~1, OFF~0 None

D4~0, D5~1, D8~2, D10~3, D16~4, D20~5 None
D0~0, D1~1, D2~2, D4~3, D8~4, D16~5, D32~6,
D64~7, D128~8, D256~9, D512~10 None
D0~0, D1~1, D2~2, D4~3, D8~4, D16~5, D32~6,
D64~7, D128~8, D256~9 None

D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8, D16~9, D32~10, D64~11 ms
D1~0, D4~1, D5~2, D8~3, D10~4, D16~5, D20~6 None

D4~0, D5~1, D8~2, D10~3, D16~4, D20~5, D32~6,
D40~7, D64~8, D80~9, D128~10, D160~11 None
D1~0, D4~1, D5~2, D8~3, D10~4, D16~5, D20~6 None
Low~2, Middle~1, High~0 None







RATE_8KBPS~1, RATE_16KBPS~2,
RATE_5440KBPS~19, RATE_11480KBPS~23 None
OFF~0, ON~1 None
Gold~0, Silver~1, Copper~2 None
Not involved %
Not involved dB
Not involved dB
Not involved %
Not involved dB
Not involved dB
Not involved %
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved %
Not involved %
Not involved %
Not involved %
RTWP~0
IUB~1
CE~2 None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None

D0.9~0, D0.8~1, D0.7~2, D0.6~3, D0.5~4, D0.4~5,
D0.3~6, D0.2~7 None
Not involved None
TTI_2MS~0, TTI_10MS~1 None

SIGNATURE0~0, SIGNATURE1~1,
SIGNATURE14~14, SIGNATURE15~15 None
SUBCHANEL0~0, SUBCHANEL1~1,
SUBCHANEL10~10, SUBCHANEL11~11 None
Not involved dB
Not involved None
Not involved dB
Not involved None
Not involved None
Not involved None
Not involved None

D8~0, D16~1, D32~2, D64~3, D128~4, D144~5,
D256~6, D384~7, D608~8, D1280~9, D2048~10,
D2720~11, D5440~12 kbit/s
D8~0, D16~1, D32~2, D64~3, D128~4, D144~5,
D256~6, D384~7, D608~8, D1280~9, D2048~10,
D2720~11, D5440~12 kbit/s
Not involved bit
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
GSM900_DCS1800_BAND_USED~0,
PCS1900_BAND_USED~1 None
NO_CAPABILITY~0, GSM~1, GPRS~2, EDGE~3 None
Not involved None

NC0~0, NC1~1, NC2~2, RESET~3 None
Not involved dB
Not involved None
Not involved None

SINGLE_HOST~0, DOUBLE_HOST~1,
DOUBLE_HOST_OUT_POOL~2 None
Not involved None
Not involved None
Not involved None

Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm
Not involved None

STTD_Supported~0, STTD_not_Supported~1 None
CP1_Supported~0, CP1_not_Supported~1 None
OFFSET1~0, OFFSET2~1 None
None~0, STTD~1 None
None~0, STTD~1 None
None~0, STTD~1 None

DELAY_ACTIVATION_SUPPORT~1,
HSDSCH_SUPPORT~2, FDPCH_SUPPORT~4,
EDCH_SUPPORT~5,
EDCH_2MS_TTI_SUPPORT~6,
EDCH_2SF2_AND_2SF4_SUPPORT~7,
EDCH_2SF2_SUPPORT~8,
EDCH_2SF4_SUPPORT~9,
EDCH_SF4_SUPPORT~10,
EDCH_SF8_SUPPORT~11,
EDCH_HARQ_IR_COMBIN_SUPPORT~12,
EDCH_HARQ_CHASE_COMBIN_SUPPORT~13,
CPC_DTX_DRX_SUPPORT~14,
CPC_HS_SCCH_LESS_OPER_SUPPORT~15,
HSPAPLUS_MIMO_SUPPORT~16,
FLEX_MACD_PDU_SIZE_SUPPORT~18,
FDPCH_SLOT_FORMAT_SUPPORT~19,
HSPAPLUS_DL_64QAM_SUPPORT~20 None
FORBIDDEN~0, NOT_FORBIDDEN~1 None
Mode0~0, Mode1~1 None
Not involved dB
Not involved None
Not involved None

Not involved None
Not involved None
Not involved ms
Not involved ms
Not involved dB
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D10~10, D11~11, D12~12,
D13~13, D14~14, D15~15 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D10~10, D11~11, D12~12,
D13~13, D14~14, D15~15 None
NO_CODING~0, CONVOLUTIONAL~1, TURBO~2 None
D1/2~0, D1/3~1 None

INTERACTIVE~2, BACKGROUND~3 None
GOLD~1, SILVER~2, COPPER~3 None
Not involved kbit/s
Not involved None
Not involved None
Not involved bit
D1~1, D2~2, D3~3 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved dB
Not involved dB
Not involved dB
Not involved dB
ALGORITHM1~1, ALGORITHM2~2 None
Not involved dB
STEPSIZE_0.5DB~0, STEPSIZE_1DB~1,
STEPSIZE_1.5DB~2, STEPSIZE_2DB~3 dB
SINGLE_TPC~0, TPC_TRIPLET_IN_SOFT~1,
TPC_AUTO_ADJUST~2 None
ON~1, OFF~0 None
Not involved None
Not involved None

D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
SCHEDULED~0, NON-SCHEDULED~1 None

D10~2, D20~3, D50~4, D100~5, D200~6, D500~7,
D1000~8 ms
D2~0, D10~2, D20~3, D50~4, D100~5, D200~6,
D500~7, D1000~8 ms
D10~2, D20~3, D50~4, D100~5, D200~6, D500~7,
D1000~8 ms
D2~0, D10~2, D20~3, D50~4, D100~5, D200~6,
D500~7, D1000~8 ms
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D608~10, D1280~13, D2048~16,
D2720~17, D5440~19 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
OFF~0, ON~1 None
D32~3, D64~4 kbit/s
EDCH_TTI_10ms~0, EDCH_TTI_2ms~1 None

D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D608~10 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D608~10, D1280~13, D2048~16,
D2720~17 kbit/s
Not involved dB
Not involved ms
Not involved byte
Not involved byte
Not involved byte
Not involved byte
MIMO~0, 64QAM~1 None

D0~0, D1~1, D2~2, D4~3, D8~4, D16~5, D32~6,
D64~7, D128~8 frame
SRB_OVER_HSDPA~0, SRB_OVER_HSUPA~1,
TTI_2MS~2, MIMO~3, 64QAM~4,
DL_L2_ENHANCE~5, DTX_DRX~6,
HSSCCH_LESS_OPERATION~7,
MIMO_64QAM~8, DC_HSDPA~9,
UL_L2_ENHANCE~10, UL_16QAM~11,
EDPCCH_BOOSTING~12, DCMIMO_HSDPA~13 None
SLOT_FORMAT_1~0, SLOT_FORMAT_4~1 None
Not involved ms
Not involved ms
MIMO_64QAM~0, DC_HSDPA~1 None
Not involved kbit/s
Not involved None
NOT_TRIGGER~0, TRIGGER~1 None
NOT_PRE_EMPTABLE~0, PRE_EMPTABLE~1 None
NOT_ALLOWED~0, ALLOWED~1 None
Not involved None
Not involved %
Not involved byte
Not involved byte
Not involved byte

Not involved %
Not involved None
DCH~0, HSPA~2 None
DCH~0, HSDPA~1, HSPA~2 None
DCH~0, HSDPA~1, HSUPA~2, HSPA~3 None
D8~1, D16~2 kbit/s
D8~1, D16~2 kbit/s

D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D512~9, D768~11, D1024~12,
D1536~14, D1800~15, D2048~16, D3600~18,
D7200~20, D8640~21, D10100~22, D13900~24 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8 kbit/s
D8~1, D16~2, D32~3, D64~4, D128~5, D144~6,
D256~7, D384~8, D608~10, D1280~13, D2048~16,
D2720~17, D5440~19 kbit/s
Not involved None
Not involved None
Not involved None

NO~0, YES~1 None
Not involved None
Not involved ms
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None

RSVDBIT31~30, RSVDBIT32~31 None
Not involved None
Not involved None
Not involved None
Not involved s
Not involved None

Not involved s
Not involved s
Not involved None
Not involved s
MAY~0, MUST~1, MUST_NOT~2 None
Not involved s
COEXIST_MEAS_THD_CHOICE_INTERFREQ~0,
COEXIST_MEAS_THD_CHOICE_INTERRAT~1 None
Not involved None
Not involved s
PO_5/15~0, PO_6/15~1, PO_8/15~2, PO_9/15~3,
PO_12/15~4, PO_15/15~5, PO_19/15~6,
PO_24/15~7, PO_30/15~8 None
PO_5/15~0, PO_6/15~1, PO_8/15~2, PO_9/15~3,
PO_12/15~4, PO_15/15~5, PO_19/15~6,
PO_24/15~7, PO_30/15~8 None
Not involved None
Not involved None

D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D2~1, D4~2, D8~3, D10~4, D20~5, D40~6,
D80~7, D160~8 ms
D0~0, D4~2, D8~3, D10~4, D20~5, D40~6, D80~7,
D160~8 ms
INTERACTIVE~2, BACKGROUND~3, NBAMR~4,
WBAMR~5 None
NOTUSED~0, USED~1 None
BIT_ALIGN~0, OCTET_ALIGN~1 None
D0~0, D1~1, D2~2, D3~3, D4~4 None
D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,

D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15, D16~16, D17~17, D18~18,
D19~19, D20~20, D21~21, D22~22, D23~23,
D24~24, D25~25, D26~26, D27~27, D28~28,
D29~29, D30~30, D31~31, D32~32, D33~33,
D34~34, D35~35, D36~36, D37~37, D38~38,
D39~39, D40~40, D41~41, D42~42, D43~43,
D44~44, D45~45, D46~46, D47~47, D48~48,
D49~49, D50~50, D51~51, D52~52, D53~53,
D54~54, D55~55, D56~56, D57~57, D58~58,
D59~59, D60~60, D61~61, D62~62, D63~63,
D64~64, D65~65, D66~66, D67~67, D68~68,
D69~69, D70~70, D71~71, D72~72, D73~73,
D74~74, D75~75, D76~76, D77~77, D78~78,
D79~79, D80~80, D81~81, D82~82, D83~83,
D84~84, D85~85, D86~86, D87~87, D88~88,
D89~89, D90~90 None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15, D16~16, D17~17, D18~18,
D19~19, D20~20, D21~21, D22~22, D23~23,
D24~24, D25~25, D26~26, D27~27, D28~28,
D29~29, D30~30, D31~31, D32~32, D33~33,
D34~34, D35~35, D36~36, D37~37, D38~38,
D39~39, D40~40, D41~41, D42~42, D43~43,
D44~44, D45~45, D46~46, D47~47, D48~48,
D49~49, D50~50, D51~51, D52~52, D53~53,
D54~54, D55~55, D56~56, D57~57, D58~58,
D59~59, D60~60, D61~61, D62~62, D63~63,
D64~64, D65~65, D66~66, D67~67, D68~68,
D69~69, D70~70, D71~71, D72~72, D73~73,
D74~74, D75~75, D76~76, D77~77, D78~78,
D79~79, D80~80, D81~81, D82~82, D83~83,
D84~84, D85~85, D86~86, D87~87, D88~88,
D89~89, D90~90 None
D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,

D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15, D16~16, D17~17, D18~18,
D19~19, D20~20, D21~21, D22~22, D23~23,
D24~24, D25~25, D26~26, D27~27, D28~28,
D29~29, D30~30, D31~31, D32~32, D33~33,
D34~34, D35~35, D36~36, D37~37, D38~38,
D39~39, D40~40, D41~41, D42~42, D43~43,
D44~44, D45~45, D46~46, D47~47, D48~48,
D49~49, D50~50, D51~51, D52~52, D53~53,
D54~54, D55~55, D56~56, D57~57, D58~58,
D59~59, D60~60, D61~61, D62~62, D63~63,
D64~64, D65~65, D66~66, D67~67, D68~68,
D69~69, D70~70, D71~71, D72~72, D73~73,
D74~74, D75~75, D76~76, D77~77, D78~78,
D79~79, D80~80, D81~81, D82~82, D83~83,
D84~84, D85~85, D86~86, D87~87, D88~88,
D89~89, D90~90 None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15, D16~16, D17~17, D18~18,
D19~19, D20~20, D21~21, D22~22, D23~23,
D24~24, D25~25, D26~26, D27~27, D28~28,
D29~29, D30~30, D31~31, D32~32, D33~33,
D34~34, D35~35, D36~36, D37~37, D38~38,
D39~39, D40~40, D41~41, D42~42, D43~43,
D44~44, D45~45, D46~46, D47~47, D48~48,
D49~49, D50~50, D51~51, D52~52, D53~53,
D54~54, D55~55, D56~56, D57~57, D58~58,
D59~59, D60~60, D61~61, D62~62, D63~63,
D64~64, D65~65, D66~66, D67~67, D68~68,
D69~69, D70~70, D71~71, D72~72, D73~73,
D74~74, D75~75, D76~76, D77~77, D78~78,
D79~79, D80~80, D81~81, D82~82, D83~83,
D84~84, D85~85, D86~86, D87~87, D88~88,
D89~89, D90~90 None

D100~0, D200~1, D400~2, D600~3, D800~4,
D1000~5, D1200~6, D1400~7, D1600~8, D1800~9,
D2000~10, D3000~11, D4000~12, D6000~13,
D8000~14 ms
Not involved None
Not involved s
D1~0, D2~8, D4~9, D10~10, D20~11, D50~1,
D100~2, D200~3, D400~4, D600~5, D800~6,
D1000~7 None
Not involved None
Not involved None
Not involved dBm
Not involved dB
Not involved dB
Not involved dBm

Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved None
Not involved None
Not involved None

Band_a~0, Band_b~1, Band_c~2, Band_d~3,
Not involved None

CHIP0~0, CHIP256~1, CHIP512~2, CHIP768~3,
CHIP1024~4, CHIP1280~5, CHIP1536~6,
CHIP1792~7, CHIP2048~8, CHIP2304~9 chip
PScramCode0~0, PScramCode1~1,
PScramCode6~6, PScramCode7~7 None
Not involved None
Not involved None

D10~0, D20~1, D40~2, D80~3, D160~4, D320~5,
D640~6, D1280~7 s
Not involved None
Not involved None
Not involved None
Not involved None
D64~0, D128~1, D192~2, D256~3, D320~4,

D384~5, D512~6 kbit/s
Not involved dB
Not involved dB
Not involved None
Not involved None
Not involved None
Not involved None

D1~1, D2~2, D3~3, D4~4 None
Not involved None
Not involved None
D64~0, D128~1, D192~2, D256~3, D320~4,

D384~5, D512~6 kbit/s
Not involved None
Not involved None
D64~0, D128~1, D192~2, D256~3, D320~4,

D384~5, D512~6 kbit/s
Not involved None

Not involved None
D64~0, D128~1, D192~2, D256~3, D320~4,

D384~5, D512~6 kbit/s
Not involved None
Not involved None
D64~0, D128~1, D192~2, D256~3, D320~4,

D384~5, D512~6 kbit/s
D0~0, D1~1, D2~2, D3~3, D4~4 None
D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,

D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15 None
D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,

D8~8, D9~9, D10~10, D11~11, D12~12, D13~13,
D14~14, D15~15 None
QPSK~0, 16QAM~1 None
D2~2, D3~3, D4~4, D5~5 None
OFF~0, ON~1 None
Fast_Dormancy~0,
HSDPA_RB_Setup_Cmp_CRC~1 None
Not involved None
Not involved None
OFF~0, ON~1 None
FD_P2D_SWITCH~0, RSVDBIT1_BIT2~1,
FD_TAC_FORCE_D2F_SWITCH~2,
RSVDBIT1_BIT32~31 None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms
Not involved None

D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved ms
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm
Not involved dBm

Not involved s
Not involved ms
Not involved None
Not involved ms
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dB
Not involved s
Not involved ms
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
D0~1, D10~2, D20~3, D30~4, D40~5, D50~6,

D60~7 s
D3~0, D6~1, D9~2, D12~3, D15~4, D18~5, D21~6,

INFINITY~7 dB
D2~0, D3~1, D4~2, D6~3, D8~4, D10~5, D12~6,

INFINITY~7 dB
Not involved None
Not involved dBm
Not involved None
Not involved dB
Not involved None

Not involved dB
Not involved dBm
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
CPICH_EC/NO~0, CPICH_RSCP~1, AUTO~2 None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved None

D1000~3, D2000~4, D3000~5, D4000~6, D6000~7,
D8000~8, D12000~9, D16000~10, D20000~11,
D24000~12, D28000~13, D32000~14, D64000~15 ms
Not involved dB
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved ms
Not involved ms
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm

Not involved dBm
Not involved dB
Not involved dB
Not involved dB
Not involved dBm
Not involved dBm

Not involved dBm
Not involved s
Not involved s
Not involved dBm
Not involved ms
Not involved None
Not involved None
Not involved s
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dBm

Not involved dBm
Not involved None
Not involved s
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved %
Not involved %
Not involved ms
Not involved None
Not involved None
Not involved s
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None

D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,
INFINITY~7
NON_PERIODIC_REPORT~0, D250~1, D500~2, None
D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,
INFINITY~7
D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
D1~0, D2~1, D4~2, D8~3, D16~4, D32~5, D64~6,
INFINITY~7
D1000~3, D2000~4, D4000~5, D8000~6,
D16000~7 ms
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dBm

Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None

D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved s
Not involved None
Not involved dB
Not involved s
Not involved dB
Not involved None
Not involved dBm
D250~0, D500~1 ms
D1~0, D2~1, D4~2, D8~3 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
AFFECT~0, NOT_AFFECT~1 None
AFFECT~0, NOT_AFFECT~1 None
Not involved dB
Not involved dB
Not involved dB
Not involved dB
D0~1, D10~2, D20~3, D30~4, D40~5, D50~6,

D60~7 s
D3~0, D6~1, D9~2, D12~3, D15~4, D18~5, D21~6,

INFINITY~7 dB
D2~0, D3~1, D4~2, D6~3, D8~4, D10~5, D12~6,

INFINITY~7 dB
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
HTTP~1, P2P~2, SPI~3, UNRECOGNIZED~4 None
IP~0, Port~1, IPAndPort~2 None
Not involved None
Not involved None
Not involved None
TCP~6, UDP~17, ALL~254 None
HIGH~0, MIDDLE~1, LOW~2 None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
OFF~0, ON~1 None
D1~0, D2~1, D3~2, D4~3, D5~4, D6~5, D7~6,

D8~7, D9~8, D10~9 None
Not involved %
Not involved None
Not involved %
Not involved None
Not involved %
Not involved None
Not involved %
Not involved None
Not involved %
Not involved None
Not involved %
Not involved None

Not involved %
Not involved None
Not involved %
Not involved None
Not involved %
Not involved None
SPU_KPI_AUTOCURE_SWITCH~0 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
IUBLDR~0, CODELDR~1, UULDR~2,

CREDITLDR~3 None

CREDITLDR~3 None

CREDITLDR~3 None

CREDITLDR~3 None
NODEB_CREDIT_LDR_SWITCH~0,
LCG_CREDIT_LDR_SWITCH~1,
LC_CREDIT_LDR_SWITCH~2 None
OFF~0, ON~1 None

Not involved s
Not involved s
Not involved s
Not involved ms
Not involved s
Not involved s
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None

Not involved ms
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved ms
Not involved min
Not involved None
Not involved ms
Not involved min
Not involved None
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min
Not involved None
Not involved ms
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
NotSupport~0, Support~1 None
False~0, True~1 None
Not involved None

Not involved None
Not involved None
Not involved min
Not involved None
Not involved None
Not involved None
D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
Not involved dB
Not involved %
Not involved %
Not involved ms
Not involved ms
CH0~0, CH1~1, CH2~2, CH3~3, CH4~4 None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
OFF~0, ON~1 None
OFF~0, ON~1 None

OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, SERVICE-BASED~1, LOAD-BASED~2,

DYNAMIC-BASED~3 None
Not involved None
Not involved None
Not involved s
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None

RRC~0, RAB~1, RRC_RAB~2 None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved s
D250~1, D500~2, D1000~3, D2000~4, D3000~5,
D4000~6, D6000~7, D8000~8, D12000~9,
D16000~10, D20000~11, D24000~12, D28000~13,
D32000~14, D64000~15 ms
Not involved dBm
Not involved dB
Not involved None
Not involved s
D250~1, D500~2, D1000~3, D2000~4, D3000~5,
D4000~6, D6000~7, D8000~8, D12000~9,
D16000~10, D20000~11, D24000~12, D28000~13,
D32000~14, D64000~15 ms
Not involved dBm
Not involved dB
OFF~0, ON~1 None
Not involved None
Not involved dB

D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
True~1, False~0 None
FTP~2, MSN~3, ICMP~5, RTSP~7, SMTP~8 None
OFF~0, ON~1 None
Not involved s
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
OFF~0, ON~1 None
RELIABILITY_CELL_SELFCURE_SWITCH~0,
CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH~1 None
PERFENH_R99_BRDCSTHSPA_SWITCH~0 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved s
Not involved min
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
SAAL~0, SCTP~1, SAAL-SCTP~2 None
Not involved None
Not involved None
SAAL~0, SCTP~1 None
ATMTODUAL~0, IPTODUAL~1, DUALTOATM~2,

DUALTOIP~3 None
SAAL~0, SCTP~1 None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
ATM_TRANS~0, IP_TRANS~1,
ATMANDIP_TRANS~2, HYBRID_IP_TRANS~3 None
SUPPORT~0, NOT_SUPPORT~1 None
Not involved ms

R99~0, R4~1, R5~2, R6~3, R7~4, R8~5, R9~6 None
OFF~0, ON~1 None
SINGLEHOST~0, PRIMHOST~1, SECHOST~2 None
Not involved None
Not involved None
DEDICATED~0, RANSHARING~1, MOCN~2 None
Not involved None
Not involved None
IUB_LDR~0, NODEB_CREDIT_LDR~1,
LCG_CREDIT_LDR~2, IUB_OLC~3 None
Not involved None
Not involved None
MBR~0, GBR~1 None

RSVDBIT16~15 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
ETH/TRUNK~0, PPP/MP~1 None
Not involved None

Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None

ATMTRANS_IP~0, IPTRANS_IP~1,
ATMANDIPTRANS_IP~2 None
Not involved None
Not involved None
Not involved None

Not involved None
NO~0, YES~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
NoAct~0, BERateRed~2, QoSRenego~3,

CSInterRatShouldBeLDHO~4,





Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None






Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None

SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,
SF128~5, SF256~6 None
SF4~0, SF8~1, SF16~2, SF32~3, SF64~4,
SF128~5, SF256~6 None
8SF4~0, 7SF4~1, 6SF4~2, 5SF4~3, 4SF4~4,

3SF4~5, 2SF4~6, SF4~7, SF8~8, SF16~9,
SF32~10, SF64~11, SF128~12, SF256~13 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

IntraFreqNCell~1, InterFreqNCell~2,
InterRatNCell~4 None
Not involved None
Not involved None
Not involved None
Not involved None

CS_SHO_SWITCH~0, HSPA_SHO_SWITCH~1,
NON_HSPA_SHO_SWITCH~2 None
OFF~0, ON~1 None

SUPPORT_CS~1, SUPPORT_PS~2,
SUPPORT_CS_AND_PS~3 None
Not involved None
R99~0, R4~1, R5~2, R6~3, R7~4, R8~5, R9~6 None
Not involved None
NO~0, YES~1 None
DL_DCCH_SWITCH~0, IUR_TRG_SWITCH~1 None
ATM_TRANS~0, IP_TRANS~1 None

CORRM_SRNSR_PSBE_RELOC~0,
CORRM_SRNSR_PSBE_DSCR~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
RNC_NODE_REDUNDANCY_COMPATIBLE_SWI
TCH~0 None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None

NOT_PERMIT_OFFLOAD~0,
PERMIT_OFFLOAD~1 None
Not involved %
OFF~0, ON~1 None

LBO_IMEITAC_SWITCH~0,
LBO_NONPDP_SWITCH~1, RSVDBIT1_BIT2~2,
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

LBO_IMEITAC_SWITCH~0,
LBO_NONPDP_SWITCH~1, RSVDBIT1_BIT2~2,
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
GOLDEN_USER~0, SILVER_USER~1,
COPPER_USER~2 None
STREAMING~0, INTERACTIVE~1,
BACKGROUND~2 None
Not involved None
SUPP_NONE~0, SUPP_IUFLEX~1,
SUPP_MOCN~2, SUPP_IUFLEX_MOCN~3 None
SUPP_NONE~0, SUPP_IUFLEX~1,
SUPP_MOCN~2, SUPP_IUFLEX_MOCN~3 None
Not involved s
Not involved None
Not involved None
Not involved None

OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved s
Not involved s
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None

NO~0, YES~1 None
Not involved None
COMM_MOCN_NRI_GLOBAL_CONFIG_MODE_S
WITCH~0,
COMM_MIB_MULTI_PLMN_LIST_ALLOWED_SWI
TCH~1, SPARE_1_SWITCH~2,
SPARE_2_SWITCH~3, SPARE_3_SWITCH~4,
SPARE_4_SWITCH~5, SPARE_5_SWITCH~6,
SPARE_6_SWITCH~7 None
Not involved None

MBR~0
Category~1
Min~2
Max~3 None
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s

Not involved kbit/s
MBR~0
Category~1
Min~2
Max~3 None
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved kbit/s
Not involved None

High~0, Medium~1, Low~2 None
Not involved None
Not involved None
Not involved None
Not involved %
FALSE~0
TRUE~1 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None

Not involved None
INTERACTIVE~2, BACKGROUND~3,
IMSSIGNALLING~4, PTT~5 None
R99~0, HSPA~1 None

D0~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D144~6, D256~7, D384~8, D608~10, D1280~13,
D2048~16, D2720~17, D5440~19 kbit/s
D0~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D144~6, D256~7, D384~8, D512~9, D768~11,
D1024~12, D1536~14, D1800~15, D2048~16,
D3600~18, D7200~20, D8640~21, D10100~22,
D13900~24, D16000~25, D21000~26 kbit/s
Not involved None

Not involved kbit/s
Not involved None

ARP~1, TrafficClass~2 None
NONE~0, DCH~1, HSPA~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved ms
Not involved ms
Not involved dB
Not involved None
Not involved None
Not involved bit
D1~1, D2~2 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dBm
Not involved dBm
Not involved dBm
Not involved dBm
Not involved None
Not involved dBm
Not involved dBm
OFF~0, ON~1 None
OFF~0, ON~1 None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
V18~0, V36~1, V72~2, V144~3 None
Not involved None
Not involved dB
LAC~0, RAC~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
REHOSTRIGHNOW~0, REHOSTDELAY~1,
REHOSTWHEN~2 None
Not involved s
Not involved s
Not involved None
Not involved None

Not involved None
Not involved None






Not involved None
Not involved None

Not involved None
Not involved None
Not involved None

D0.9~0, D0.8~1, D0.7~2, D0.6~3, D0.5~4, D0.4~5,
D0.3~6, D0.2~7 None
Not involved None
Not involved None
Not involved dB
Not involved None
Not involved dB
BIT16~6, BIT24~7 bit
Not involved None
Not involved None
D1~1, D2~2, D3~3, D4~4 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved None
Not involved None
Not involved None
Not involved None

Not involved dB
Not involved dB
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
ON~0, OFF~1 None
Not involved None
Not involved ms
Not involved None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved s
Not involved s
Not involved s
Not involved s
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2k~8, D3k~9, D4k~10,
D6k~11, D8k~12, D12k~13, D16k~14, D24k~15,
D32k~16, D48k~17, D64k~18, D96k~19,
D128k~20, D192k~21, D256k~22, D384k~23,
D512k~24, D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
Not involved ms
Not involved bit/s
Not involved None
Not involved None
Not involved s
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2k~8, D3k~9, D4k~10,
D6k~11, D8k~12, D12k~13, D16k~14, D24k~15,
D32k~16, D48k~17, D64k~18, D96k~19,
D128k~20, D192k~21, D256k~22, D384k~23,
D512k~24, D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,
D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
OFF~0, ON~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
None~0, RateDegrade~1, InterFreqHO~2,

InterRatHO~3 None

InterRatHO~3 None

InterRatHO~3 None
Not involved ms
InterRatHO~3 None

InterRatHO~3 None

InterRatHO~3 None
SINGLE~0, COMBINE~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
Not involved ms
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None

Not involved ms
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None
NO~0, YES~1 None

Not involved s
Not involved dB
Not involved s
Not involved s

D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,

D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved min
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
OFF~0, ON~1 None
Not involved None
Not involved ms
Not involved s
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved frame
Not involved frame
Not involved None
Not involved None

Not involved None
Not involved bit
D1~1, D2~2 None
Not involved None
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved %
Not involved ms
Not involved dB
Not involved dB
AMR~0, VP~1, PSR99~2, PSHSPA~3 None
OFF~0, ONLY_TO_INTER_FREQUENCY~1,
ONLY_TO_INTER_RAT~2 None
Not involved %
Not involved %

Not involved None
Not involved None
Not involved None
SF4~4, SF8~8, SF16~16, SF32~32, SF64~64,

SF128~128, SF256~256 None
Not involved None
Not involved None
PsBlk~0, CsAndPsBlk~1 None

Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None

OFF~0, ON~1 None
GERMAN~0, ENGLISH~1, ITALIAN~2,
FRENCH~3, SPANISH~4, DUTCH~5,
SWEDISH~6, DANISH~7, PORTUGUESE~8,
FINNISH~9, NORWEGIAN~10, GREEK~11,
TURKISH~12, HUNGARIAN~13, POLISH~14,
LANGUAGEUNSPECIFIED~15 None
Not involved s
Not involved None
OFF~0, ON~1 None
Not involved s
Not involved s
D16~0, D32~1, D64~2, D128~3, D256~4 kbit/s
Not involved %
Not involved None
Not involved None

Not involved None
Not involved None
Not involved s
Not involved s
ON~1, OFF~0 None
ON~1, OFF~0 None
ON~1, OFF~0 None

D8~0, D16~1, D32~2, D64~3, D128~4, D144~5,
D256~6 kbit/s
Not involved None
Not involved None
Not involved s
Not involved None
Not involved None
NONE~0, IUCS~1, IUPS~2, IUCS_IUPS~3 None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
ORIGCONVCALLEST~0,
ORIGSTREAMCALLEST~1,
ORIGINTERCALLEST~2, ORIGBKGCALLEST~3,
ORIGSUBSTRAFFCALLEST~4,
TERMCONVCALLEST~5,
TERMSTREAMCALLEST~6,
TERMINTERCALLEST~7, TERMBKGCALLEST~8,
EMERGCALLEST~9,
INTERRATCELLRESELEST~10,
INTERRATCELLCHGORDEREST~11,
REGISTEST~12, DETACHEST~13,
ORIGHIGHPRIORSIGEST~14,
ORIGLOWPRIORSIGEST~15, CALLREEST~16,
TERMHIGHPRIORSIGEST~17,
TERMLOWPRIORSIGEST~18,
TERMCAUSEUNKNOWN~19,
MBMSCALLEST~20, DEFAULTEST~21 None
FACH~0, DCH_3.4K_SIGNALLING~1,
DCH_6.8K_SIGNALLING~2,
DCH_27.2K_SIGNALLING~4 None
OFF~0, ON~1 None
Not involved None

INVOKE_TRACE_SWITCH~0,
SYS_INFO_UPDATE_FOR_IU_RST~1,
DRNC_DIRECT_DSCR~2,
RNC_SHARE_SWITCH~4,
RNCAP_IMSI_HO_SWITCH~5,
TERMINAL_VERSION_DEBASE_SWITCH~6,
SYS_HO_OUT_CIPHER_SWITCH~7,
SYS_HO_CIPHER_CONFIG~8,
BARRED_CELL_FOR_CSDOMAIN_RST~9,
CR2284R1_SWITCH~10,
CDT_MSG_FULL_TRACE~11,
CR2284R1_COMPATIBLE_SWITCH~12,
COMBINE_OPERATION_DRD_SWITCH~13,
UL_INTER_PROTECT_SWITCH~14,
FAST_DORMANCY_SWITCH~15,
SYS_HO_IN_CIPHER_SWITCH~16,
PTT_EARLY_TRANS_SWITCH_OFF~17,
UPLINK_MDC_ENHENCEMENT_SWITCH~18,
NODEB_PRIVATE_INTERFACE_SWITCH~19,
PTT_SPEC_LI_SWITCH_OFF~20,
RNC_DF_2_URA_PCH_SWITCH~21,
FD_TAC_MATCH_SWITCH~22 None
LOAD_IRAT_HO_RNC_FILL_TL~0,
SEND_IDT_JUDGE_IU_RESET~1,
RNC_RBRECFG_DRD_FAIL_ROLLBACK_SWITC
H~2, RNC_CS_QUERY_UE_IMEI_SWITCH~3,
RNC_PS_QUERY_UE_IMEI_SWITCH~4,
RNC_FD_FACH_CONG_CTRL_SWITCH~5,
RNC_RBSETUP_DRD_FAIL_ROLLBACK_SWITC
H~6, FP_IUUP_TRACE_SWITCH~16 None
RSVDBIT1_BIT1~0, NAS_QOS_MOD_SWITCH~1,
SYSHO_CSIN_PERMIT_SWITCH~16,
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
Not involved None
OFF~0, ON~1 None
Not involved None
Not involved None
Not involved s
Not involved s
Not involved s
Not involved ms
Not involved s
Not involved s
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved ms
Not involved min

Not involved None
Not involved ms
Not involved min
Not involved None
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min
Not involved None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved ms
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved chip
Not involved None
Not involved None
Not involved chip
Not involved None

BIT16~6, BIT24~7 bit
D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D10~10, D11~11, D12~12,
D13~13, D14~14, D15~15, D16~16, D17~17 None
EXISTS~0, NOT_EXISTS~1 None
COMMON~0, MCCH~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

CELLID_CENTER~0, CELLID_RTT~1, OTDOA~2,
AGPS~3 None
UE_BASED~0, UE_ASSISTED~1,
UE_BASED_PREFERRED~2,
UE_ASSISTED_PREFERRED~3 None
NODELIVERY~0, DELIVERY~1 None
REFERENCE_TIME_FOR_GPS~0,
REFERENCE_LOCATION_FOR_GPS~1,
DGPS_CORRECT~2, GPS_NAVGMODEL~3,
GPS_IONOSPHERIC_MODEL~4,
GPS_UTC_MODEL~5, GPS_ALMANAC~6,
GPS_ACQ_ASSIST~7,
GPS_REALTIME_INTEGRITY~8 None
REFERENCE_TIME_FOR_GPS~0,
REFERENCE_LOCATION_FOR_GPS~1,
DGPS_CORRECT~2, GPS_NAVGMODEL~3,
GPS_IONOSPHERIC_MODEL~4,
GPS_UTC_MODEL~5, GPS_ALMANAC~6,
GPS_ACQ_ASSIST~7,
GPS_REALTIME_INTEGRITY~8 None
Not involved None
OFF~0, ON~1 None
NO~0, YES~1 None
DRD~0, MEAS_BASED~1 None
R5_POSDATA_SWITCH~0,
LAST_KNOWN_SERVICE_AREA_SWITCH~1 None
OFF~0, ON~1 None

Not involved dB
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dB
RNC_CENTRIC~0, SAS_CENTRIC~1,
SAS_CENTRIC_PREFERRED~2 None
D250~1, D500~2, D1000~3, D2000~4, D3000~5,
D4000~6, D6000~7, D8000~8, D12000~9,
D16000~10, D20000~11 ms
POINT~0, POINT_WITH_UNCERTN~1,
ELPSD_POINT_WITH_UNCERTN_ELLIPSE~2,
ELPSD_POINT_WITH_ALT~3,
ELPSD_POINT_WITH_ALT_AND_UNCERTN_ELP
SD~4, ELPSD_ARC~5, AUTOMATIC~6 None
Not involved None
Not involved None
CELL_ANTENNA~0, CELL_CENTER~1, BOTH~2 None
DEG~0, SEC~1 None
MET~0, IMP~1 None
Not involved degree
Not involved degree
Not involved m
Not involved m
Not involved degree
Not involved degree

Not involved m
Not involved m
NLOS_ENVIRONMENT~0,
LOS_ENVIRONMENT~1,
MIXED_ENVIRONMENT~2 None
Not involved degree
Not involved degree
Not involved m
Not involved m
Not involved m
Not involved degree
Not involved m
Not involved second
Not involved second
Not involved second
Not involved second
Not involved m
Not involved m
Not involved m
Not involved m
Not involved m
Not involved m
Not involved m
Not involved m
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved %
FALSE~0
TRUE~1 None
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %
Not involved None
Not involved None
Not involved s
Not involved ms
Not involved s
Not involved s
Not involved s
RT~1, NRT~2, ALL~3 None
Not involved None

Not involved None
Not involved dB
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved ms
Not involved min
Not involved ms
Not involved ms
Not involved ms
Not involved s
Not involved s
Not involved s


Not involved None
Not involved None
SPEECH~0, UNKNOWN~1 None
Not involved bit/s
Not involved None
Not involved None
HO_TO_GSM_SHOULD_BE_PERFORM~0,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM~1,
HO_TO_GSM_SHALL_NOT_BE_PERFORM~2 None
GSM~0, GPRS~1, EDGE~2 None
NORMAL~0, SILENT~1 None

APPLIED_ON_UPLINK~0,
APPLIED_ON_DOWNLINK~1,
APPLIED_ON_BOTH~2 None
HO_TO_EUTRAN_SHOULD_BE_PERFORM~0,
HO_TO_EUTRAN_SHALL_NOT_BE_PERFORM~1 None
Not involved None
UPLINK~0, DOWNLINK~1 None
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2K~8, D3K~9, D4K~10, D6K~11,
D8K~12, D12K~13, D16K~14, D24K~15, D32K~16,
D48K~17, D64K~18, D96K~19, D128K~20,
D192K~21, D256K~22, D384K~23, D512K~24,
D768K~25 byte
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2K~8, D3K~9, D4K~10,
D6K~11, D8K~12, D12K~13, D16K~14, D24K~15,
D32K~16, D48K~17, D64K~18, D96K~19,
D128K~20, D192K~21, D256K~22, D384K~23,
D512K~24 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15, D10000~16, D15000~17, D20000~18,
D25000~19, D30000~20 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15, D10000~16, D15000~17, D20000~18,
D25000~19, D30000~20 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
TRCH_HSDSCH~1, TRCH_EDCH_2MS~2,
TRCH_EDCH_10MS~3 None
D10~0, D20~1, D30~2, D40~3, D50~4, D60~5,
D70~6, D80~7, D90~8, D100~9, D120~10,
D140~11, D160~12, D200~13, D300~14, D400~15 ms
D4~0, D6~1, D8~2, D12~3, D16~4, D24~5, D32~6,
D64~7, D128~8 None
D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8 None
Not involved bit

Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
D20~0, D40~1, D60~2, D80~3, D100~4, D120~5,

D140~6, D160~7, D180~8, D200~9, D250~10,
D300~11, D400~12, D500~13, D750~14,
D1000~15, D1250~16, D1500~17, D1750~18,
D2000~19, D2500~20, D3000~21, D3500~22,
D4000~23, D4500~24, D5000~25, D7500~26 ms
Not involved None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8, D9~9, D10~10, D11~11, D12~12 None
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit
Not involved bit

D2~0, D10~1, D20~2, D50~3, D100~4, D200~5,
D500~6, D1000~7 ms
Not involved None
Not involved ms
Not involved None
Not involved None
TRCH_EDCH_2MS~2, TRCH_EDCH_10MS~3 None
Not involved dB
Not involved dB
Not involved dB
Not involved None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,
PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,
PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
Not involved None
Not involved None
PO_8/15~0, PO_11/15~1, PO_15/15~2,

PO_21/15~3, PO_30/15~4, PO_42/15~5,
PO_60/15~6, PO_84/15~7 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

TRCH_DCH~0, TRCH_EDCH_2MS~2,
TRCH_EDCH_10MS~3 None
Not involved None

Not involved None
Not involved dB
Not involved None
Not involved None
Not involved None
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved dB
Not involved None

Not involved None
Not involved None
Not involved dB
Not involved dB
Not involved None
Not involved None
TRCH_DCH~0, TRCH_HSDSCH~1,
TRCH_DCH~0, TRCH_HSDSCH~1 None
Not involved None

AM~1, UM~2, TM~3 None
SENDER_PARA~0, RECEIVE_PARA~1,
FLOWCONTROL_PARA~3 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
D50~0, D100~1, D150~2, D200~3, D250~4,
D300~5, D350~6, D400~7, D450~8, D500~9,
D550~10, D600~11, D700~12, D800~13, D900~14,
D1000~15 ms
D1~0, D4~1, D6~2, D8~3, D12~4, D16~5, D24~6,
D32~7 None
TIMER_BASED_WITH_EXPLICIT_SIGNALLING~1,
DISCARD_AFTER_MAX_DAT_RETRANSMISSION
S~3, NO_DISCARD~4 None
NOTUSED~255,
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLIN
G~2 None
D50~0, D60~1, D70~2, D80~3, D90~4, D100~5,
D120~6, D140~7, D160~8, D180~9, D200~10,
D300~11, D400~12, D500~13, D700~14, D900~15 ms
D100~0, D250~1, D500~2, D750~3, D1000~4,
D1250~5, D1500~6, D1750~7, D2000~8, D2500~9,
D3000~10, D3500~11, D4000~12, D4500~13,
D5000~14, D7500~15 ms
D1~0, D4~1, D6~2, D8~3, D12~4, D16~5, D24~6,
D32~7 None
D10~0, D20~1, D30~2, D40~3, D50~4, D60~5,
D70~6, D80~7, D90~8, D100~9 ms
D2~1, D3~2, D4~3, D5~4, D6~5, D7~6, D8~7,
D9~8, D10~9, D15~10, D20~11, D25~12, D30~13,
D35~14, D40~15 None
D50~0, D60~1, D70~2, D80~3, D90~4, D100~5,
D120~6, D140~7, D160~8, D180~9, D200~10,
D300~11, D400~12, D500~13, D700~14, D900~15 ms
D1~0, D4~1, D6~2, D8~3, D12~4, D16~5, D24~6,
D32~7 None
D1~0, D2~1, D3~2, D4~3, D5~4, D6~5, D7~6,
D8~7, D9~8, D10~9, D15~10, D20~11, D25~12,
D30~13, D35~14, D40~15 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
NOTUSED~255, D10~0, D20~1, D30~2, D40~3,

D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D100~0, D200~1, D300~2,
D400~3, D500~4, D750~5, D1000~6, D2000~7 ms

NOTUSED~255, D10~0, D20~1, D30~2, D40~3,
D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D10~0, D20~1, D30~2, D40~3,

D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D1~0, D2~1, D4~2, D8~3, D16~4,
D32~5, D64~6, D128~7 ms
NOTUSED~255, D1~0, D4~1, D16~2, D64~3 ms

NOTUSED~255, D50~0, D60~1, D70~2, D80~3,
D85~4, D90~5, D95~6, D99~7 None
NOTUSED~255, D100~0, D200~1, D300~2,
D400~3, D500~4, D750~5, D1000~6, D2000~7 ms
Not involved ms
Not involved ms
Not involved None
Not involved %
Not involved None
Not involved None
Not involved %
Not involved None
Not involved None
Not involved ms
NOTUSED~255, D1~0, D2~1, D4~2, D8~3, D16~4,
D32~5, D64~6, D128~7 ms
NOTUSED~255, D1~0, D4~1, D16~2, D64~3 ms

NOTUSED~255, D1~0, D2~1, D4~2, D8~3, D16~4,
D32~5, D64~6, D128~7 ms
NOTUSED~255, D1~0, D4~1, D16~2, D64~3 ms
Not involved None
Not involved dB
Not involved dB
Not involved dB
Not involved None

D1~1, D2~2, D3~3, D4~4, D5~5, D6~6, D7~7,
D8~8 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
Not involved None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,
PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,

PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
PO_5/15~0, PO_6/15~1, PO_7/15~2, PO_8/15~3,
PO_9/15~4, PO_11/15~5, PO_12/15~6,
PO_13/15~7, PO_15/15~8, PO_17/15~9,
PO_19/15~10, PO_21/15~11, PO_24/15~12,
PO_27/15~13, PO_30/15~14, PO_34/15~15,
PO_38/15~16, PO_42/15~17, PO_47/15~18,
PO_53/15~19, PO_60/15~20, PO_67/15~21,
PO_75/15~22, PO_84/15~23, PO_95/15~24,
PO_106/15~25, PO_119/15~26, PO_134/15~27,
PO_150/15~28, PO_168/15~29, PO_189/15~30,
PO_212/15~31, PO_237/15~32, PO_267/15~33,
PO_299/15~34, PO_336/15~35, PO_377/15~36 None
Not involved None
Not involved None
PO_8/15~0, PO_11/15~1, PO_15/15~2,

PO_21/15~3, PO_30/15~4, PO_42/15~5,
PO_60/15~6, PO_84/15~7 None
Not involved None
Not involved None
Not involved None
Not involved None

TRCH_DCH~0, TRCH_HSDSCH~1,
TRCH_DCH~0, TRCH_HSDSCH~1 None
Not involved None
Not involved None
AM~1, UM~2 None

EDIT_SENDER_PARA~0,
EDIT_RECEIVE_PARA~1 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
D50~0, D100~1, D150~2, D200~3, D250~4,
D300~5, D350~6, D400~7, D450~8, D500~9,
D550~10, D600~11, D700~12, D800~13, D900~14,
D1000~15 ms
TIMER_BASED_WITH_EXPLICIT_SIGNALLING~1,
DISCARD_AFTER_MAX_DAT_RETRANSMISSION
S~3, NO_DISCARD~4 None
NOTUSED~255,
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLIN
G~2 None
D50~0, D60~1, D70~2, D80~3, D90~4, D100~5,
D120~6, D140~7, D160~8, D180~9, D200~10,
D300~11, D400~12, D500~13, D700~14, D900~15 ms
D100~0, D250~1, D500~2, D750~3, D1000~4,
D1250~5, D1500~6, D1750~7, D2000~8, D2500~9,
D3000~10, D3500~11, D4000~12, D4500~13,
D5000~14, D7500~15 ms
D1~0, D4~1, D6~2, D8~3, D12~4, D16~5, D24~6,

D32~7 None
D10~0, D20~1, D30~2, D40~3, D50~4, D60~5,
D70~6, D80~7, D90~8, D100~9 ms
D2~1, D3~2, D4~3, D5~4, D6~5, D7~6, D8~7,
D9~8, D10~9, D15~10, D20~11, D25~12, D30~13,
D35~14, D40~15 None
D50~0, D60~1, D70~2, D80~3, D90~4, D100~5,
D120~6, D140~7, D160~8, D180~9, D200~10,
D300~11, D400~12, D500~13, D700~14, D900~15 ms
D1~0, D4~1, D6~2, D8~3, D12~4, D16~5, D24~6,

D32~7 None
D1~0, D2~1, D3~2, D4~3, D5~4, D6~5, D7~6,
D8~7, D9~8, D10~9, D15~10, D20~11, D25~12,
D30~13, D35~14, D40~15 None
D1~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D256~6, D512~7, D768~8, D1024~9, D1536~10,
D2047~11, D2560~12, D3072~13, D3584~14,
D4095~15 None
NOTUSED~255, D10~0, D20~1, D30~2, D40~3,

D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D100~0, D200~1, D300~2,

D400~3, D500~4, D750~5, D1000~6, D2000~7 ms

NOTUSED~255, D10~0, D20~1, D30~2, D40~3,
D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D10~0, D20~1, D30~2, D40~3,

D50~4, D60~5, D70~6, D80~7, D90~8, D100~9,
D110~10, D120~11, D130~12, D140~13, D150~14,
D160~15, D170~16, D180~17, D190~18, D200~19,
D210~20, D220~21, D230~22, D240~23, D250~24,
D260~25, D270~26, D280~27, D290~28, D300~29,
D310~30, D320~31, D330~32, D340~33, D350~34,
D360~35, D370~36, D380~37, D390~38, D400~39,
D410~40, D420~41, D430~42, D440~43, D450~44,
D460~45, D470~46, D480~47, D490~48, D500~49,
D510~50, D520~51, D530~52, D540~53, D550~54,
D600~55, D650~56, D700~57, D750~58, D800~59,
D850~60, D900~61, D950~62, D1000~63 ms
NOTUSED~255, D1~0, D2~1, D4~2, D8~3, D16~4,

D32~5, D64~6, D128~7 ms
NOTUSED~255, D1~0, D4~1, D16~2, D64~3 ms
NOTUSED~255, D50~0, D60~1, D70~2, D80~3,

D85~4, D90~5, D95~6, D99~7 None
NOTUSED~255, D100~0, D200~1, D300~2,

D400~3, D500~4, D750~5, D1000~6, D2000~7 ms
NOTUSED~255, D1~0, D2~1, D4~2, D8~3, D16~4,

D32~5, D64~6, D128~7 ms
NOTUSED~255, D1~0, D4~1, D16~2, D64~3 ms
MeasurementQuantity~0, Both~1 None

D0~0, D1~1, D2~2, D3~3, D4~4, D5~5, D6~6,
D7~7, D8~8, D9~9, D11~10, D13~11, D15~12,
D17~13, D19~14 None
Not involved s
RSRP~0, RSRQ~1 None
Not involved dB
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,

D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved dBm
Not involved dB
UEA0~0, UEA1~1 None

Not involved None
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2k~8, D3k~9, D4k~10,
D6k~11, D8k~12, D12k~13, D16k~14, D24k~15,
D32k~16, D48k~17, D64k~18, D96k~19,
D128k~20, D192k~21, D256k~22, D384k~23,
D512k~24, D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2k~8, D3k~9, D4k~10,
D6k~11, D8k~12, D12k~13, D16k~14, D24k~15,
D32k~16, D48k~17, D64k~18, D96k~19,
D128k~20, D192k~21, D256k~22, D384k~23,
D512k~24, D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,
D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D8~0, D16~1, D32~2, D64~3, D128~4, D256~5,

D512~6, D1024~7, D2k~8, D3k~9, D4k~10,
D6k~11, D8k~12, D12k~13, D16k~14, D24k~15,
D32k~16, D48k~17, D64k~18, D96k~19,
D128k~20, D192k~21, D256k~22, D384k~23,
D512k~24, D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D250~0, D500~1, D1000~2, D2000~3, D4000~4,

D8000~5, D16000~6 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
Not involved ms
Not involved kbit/s
Not involved None

Not involved None
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,
D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,

D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
D0~0, D10~1, D20~2, D40~3, D60~4, D80~5,
D100~6, D120~7, D160~8, D200~9, D240~10,
D320~11, D640~12, D1280~13, D2560~14,
D5000~15 ms
D16~1, D32~2, D64~3, D128~4, D256~5, D512~6,
D1024~7, D2k~8, D3k~9, D4k~10, D6k~11,
D8k~12, D12k~13, D16k~14, D24k~15, D32k~16,
D48k~17, D64k~18, D96k~19, D128k~20,
D192k~21, D256k~22, D384k~23, D512k~24,
D768k~25 byte
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
Not involved s
UIA1~1 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

INTERACTIVE~2, BACKGROUND~3,
IMSSIGNALLING~4, PTT~5 None
R99~0, HSPA~1 None

D0~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D144~6, D256~7, D384~8, D608~10, D1280~13,
D2048~16, D2720~17, D5440~19 kbit/s
D0~0, D8~1, D16~2, D32~3, D64~4, D128~5,
D144~6, D256~7, D384~8, D512~9, D768~11,
D1024~12, D1536~14, D1800~15, D2048~16,
D3600~18, D7200~20, D8640~21, D10100~22,
D13900~24, D16000~25, D21000~26 kbit/s
Not involved kbit/s
D3.4~1, D13.6~3, D27.2~5 kbit/s
D3.4~1, D13.6~3, D27.2~5 kbit/s

D0~0, D8~2, D16~4, D32~6, D64~7, D128~8,
D144~9, D256~10, D384~11 kbit/s
D0~0, D8~2, D16~4, D32~6, D64~7, D128~8,
D144~9, D256~10, D384~11 kbit/s
D0~0, D8~2, D16~4, D32~6, D64~7, D128~8,
D144~9, D256~10, D384~11 kbit/s
D0~0, D8~2, D16~4, D32~6, D64~7, D128~8,
D144~9, D256~10, D384~11 kbit/s
Not involved %
Not involved %
Not involved %
Not involved %
Not involved %

ARP~1, TrafficClass~2 None
NONE~0, DCH~1, HSPA~2 None
Not involved None
OFF~0, ON~1 None
ALGORITHM_OFF~0, ALGORITHM_ON~1 None
PRIORITY1~0, PRIORITY2~1, PRIORITY3~2,

PRIORITY10~9, PRIORITY11~10,
PRIORITY12~11, PRIORITY13~12,
PRIORITY14~13 None
Not involved None
SAALLNK~1, IPOAPVC~2, AAL2PATH~3 None
Not involved None
Not involved None
Not involved None
Not involved None

Not involved None
Not involved None
NO_LOOP~0, LOCAL_LOOP~1 None
Not involved min
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
UNI~3, IMA~4, FRAATM~5, NCOPT~6 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
UNI~3, IMA~4, FRAATM~5, NCOPT~6 None
Not involved None
Not involved None
Not involved None

Not involved None
VPLCX~1, VCLCX~0 None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None
Not involved None

Actual Value Range Default Value
0~2 1
0~4599 None
1~4294967295 None
UNI, IMA, FRAATM, NCOPT, ATMLOGICPORT, NULL None
0~11 None
0~5, 8~27 None
0~335 None
0~167 None
0~31 None
0~7 None
0~767 None
NO, YES None
0~2047 None
0~4095 None
32~65535 None
100~1999 None
100~1999 None
PEER, LOCAL LOCAL
0~199 0
1~64, step:0.05 10
R99, HSPA, SHARE None
None None
0~4599 None
0~4294967295 None
NO, YES YES
5000~30000 7000
5000~30000 5000
2000~60000 5000
2000~60000 3000
2000~60000 5000
2000~60000 5000
2000~60000 5000
5000~30000 10000
5000~30000 10000
0~4599 None
IUB, IUR, IUCS, IUPS None
ATM, IP, ATM_IP, HYBRID_IP None
SHARE, EXCLUSIVE None
0~3 None
0~163 None
0~163 None
0~163 None
0~33 None
0~63 None
0~63 None
0~63 None
0~4599 None
1~64 characters None
IUB, IUR, IUCS, IUPS, UNI_AAL2SWITCH,

NNI_AAL2SWITCH None
0~65535 None
NO, YES None
0~186 None
NO, YES None
0~4599 None
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~1399 None
CS1, CS2 CS2
1~65535 None
0~65534 0
0~250 0
0~250 0
0~100 0
0~100 0
DISABLE, ENABLE ENABLE
DISABLE, ENABLE ENABLE
60~65534 900
10000~150000 150000
7~90 90
1~2147483646 None
1~65535 None
Critical, Major, Minor, Warning None
ON, OFF None
0~11 None
1~32 None
CLOSE, OPEN CLOSE
65334~65383 None
BOOL, VALUE None
LOW, HIGH HIGH
0~9 characters 90
0~9 characters 10
1~65535 None
unshielded, shielded unshielded
ON, OFF ON
30~1024 90
ON, OFF ON
0~11 None
0~5, 8~27 None

Hub, Leaf None
AEUa, AOUa, UOIa, AOUc, UOIc None
0~767 None
IMA, UNI, FRA, NCOPT, ATMLOGICPORT None
{0~5}, {8~27} None
0~167 None
0~335 None
0~31 None
0~7 None
0~191(AEUa), 0~383(AOUa), 0~447(UOIa_ATM),
0~767(AOUc), 0~767(UOIc) None
512~149000 None
512~149000 None
0~3 None
OFF, ON ON
0~1999 1
0~199 0
0~767 None
0~1999 None
0~199 None
100~1999 None
UBR, CBR, RTVBR, NRTVBR, UBR_PLUS None
CELL/S, KBIT/S None
30~353207 None
30~353207 None
30~70754 None
3~10000 None
1024~212000 1024
0~11 None
0~27 None
BFD_OFF, BFD_ON None
1~65535 None
nonrpt, rpt None
0~11 None
0~27 None
SCU, INT None
YES None
SCUb None
INT, DPU, XPU, OMU, SAU, NIU None
PEUa, AEUa, FG2a, GOUa, AOUa, POUa, UOIa, AOUc,

POUc, UOIc, FG2c, GOUc, SPUa, SPUb, DPUb, DPUe,
OMUa, OMUb, OMUc, SAUa, NIUa None
OAM, UCP, RUCP, UUP, ATM, IP, SAU, NIU None
YES, NO None
0~11 None
0~27 None
NO, YES None
LS, BAK None
1~3 None
CENTRALIZED, DISTRIBUTED CENTRALIZED
0~3 None
G_15, G_16, G_17, G_18, G_19, G_20, G_21, G_22, G_23,

G_24, G_25, G_26, G_27, G_28, G_29, G_30, G_31 None

G_15, G_16, G_17, G_18, G_19, G_20, G_21, G_22, G_23,
G_24, G_25, G_26, G_27, G_28, G_29, G_30, G_31 None
DISABLE, ENABLE None
0~11 None
0~11 None
0~11 None
0~5, 8~27 None
0~7 None
2~4094 None
0~499 None
10, 100, 1000 1000
0~11 None
0~5, 8~27 None

0~7 None
0~7 0
0~11 None
0~11 None
0~499 None
LocalMep,
RemoteMep None
1~1000 None
ETHER, TRUNK None
0~5, 8~27 None
0~7(FG2a), 0~1(GOUa), 0~11(FG2c), 0~3(GOUc) None
0~11 None
MPS, EPS None
1~11 None
0~27 None
AEUa, PEUa, AOUa, POUa, UOIa, AOUc, POUc, UOIc None
0~31 0
NO, YES NO
0~31 0
NO, YES NO
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
MANUAL, AUTO, FREE AUTO
1~4 None
1~4 None
BITS1-2MHZ, BITS2-2MHZ, BITS1-2MBPS, BITS2-2MBPS,

GPS, 8KHZ, LINE1_8KHZ, LINE2_8KHZ, BITS1-1.5MBPS,
BITS2-1.5MBPS None
GCUa, GCGa GCUa
ON, OFF None
ALL, ONLY_SSL ALL
0~11 None
0~5, 8~27 None
AOUa, POUa, AOUc, POUc None
ALL, PORT, SINGLE None

0~3 None
0~83 None
NULL, 1BYTE, 16BYTE, 64BYTE None
Hexadecimal, Character_String None
ZERO, SPACE None
0~65535 None
OFF, SERVICE-BASED, LOAD-BASED, DYNAMIC-BASED OFF
-100~100 10
-100~100 30
SCU, GCU, MPU, UCP, DPU, INT, NIU None
20~99 75
30~100 85
20~99 80
30~100 85
20~99 75
30~100 90
NBAP_CCP, NBAP_NCP, IUB_OAM, ALCAP None
0~100 None
0~11 None
0~5, 8~27 None
LOGIC_IP, IPOA_CLIENT_IP None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
776~1696 1696
0~63 None
0.0.0.0~255.255.255.255 None
0~63 None
0~7 None
0~11 None
0~5, 8~27 None
AEUa, AOUa, AOUc, PEUa, POUa, POUc None

ALL, SINGLE None
0~31(AEUa/PEUa), 0~125(E1 of AOUa/POUa), 0~167(T1 of
AOUa/POUa), 0~251(E1 of AOUc/POUc), 0~335(T1 of
AOUc/POUc) None
NO, YES None
E1_UNBA, E1_BA, T1, E1 None
E1_DOUBLE_FRAME, E1_CRC4_MULTI_FRAME,
T1_SUPER_FRAME, T1_EXTENDED_SUPER_FRAME None
B8ZS, HDB3, AMI, AMI_ZCS None
OFF, ON None
OFF, ON None
OFF, ON None
0~11 None
0~5, 8~27 None
AEUa, AOUa, AOUc, PEUa, POUa, POUc None

0~31(AEUa/PEUa), 0~125(E1 of AOUa/POUa), 0~167(T1 of
AOUa/POUa), 0~251(E1 of AOUc/POUc), 0~335(T1 of
AOUc/POUc) None
NO_LOOP, REMOTE_LOOP, LINE_REMOTE_LOOP,

LOCAL_LOOP, PAYLOAD_LOOP, SIN_CHN_LOC,
CIN_CHN_REM None
TS1, TS2, TS3, TS4, TS5, TS6, TS7, TS8, TS9, TS10, TS11,
TS12, TS13, TS14, TS15, TS16, TS17, TS18, TS19, TS20,
TS30, TS31 None
TS30, TS31 None
1~65535 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
CLOSE, OPEN OPEN
VOLTAGE, CURRENT CURRENT
1~9 characters 57
1~9 characters 42
1~9 characters 28
1~9 characters 20
1~9 characters 45
1~9 characters 0
1~9 characters 80
1~9 characters 10
1~9 characters 0.02
1~9 characters 0.004
1~9 characters 100
1~9 characters 0
1~9 characters 0.02
1~9 characters 100
1~9 characters 0
1~9 characters 0.02
1~9 characters 100
1~9 characters 0
1~9 characters 0.02
1~9 characters 100
1~9 characters 0
CLOSE, OPEN CLOSE
CLOSE, OPEN CLOSE
CLOSE, OPEN CLOSE
CLOSE, OPEN CLOSE
CLOSE, OPEN CLOSE
CLOSE, OPEN CLOSE
1~65535 None

power, env, sig, trunk, hardware, software, run, comm, service,
handle, integrity, ope, physical, sec, time None
0~11 None
0~5, 8~27 None
0~5 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None
FG2a, GOUa, FG2c, GOUc None
FE, GE None
ENABLE, DISABLE None
1000M, AUTO None

256~1650 None
OFF, ON None
0~100 None
OFF, ON None
0~1999 None
OFF, ON OFF
O1E3_R5E4, O5E4_R1E4, O1E4_R5E5, O5E5_R1E5,

O1E5_R5E6, O5E6_R1E6 O5E4_R1E4
80~2000 None
80~2000 None
V7, V8 V7
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~11 None
0~5, 8~27 None
LOAD_SHARING, ACTIVE_STANDBY LOAD_SHARING

0~65535 100
NON-REVERTIVE, REVERTIVE NON-REVERTIVE
STATIC_LACP, MANUAL_AGGREGATION None
0~100 0
OFF, ON ON
0~1999 0
V7, V8 V7
0~11 None
0~5, 8~27 None
0~5 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None
0~5, 8~27 None
LOAD_SHARING, ACTIVE_STANDBY LOAD_SHARING

0~65535 None
10~15 10
30~35 30
OFF, ON OFF
NORMAL_FAN, IND_FAN None
0~11 None
HW_AUTO_TEMPERATURE_CONTROL, SPECIFY_RATE,
SOFTWARE_CONTROL SOFTWARE_CONTROL
55~100 None
SCU, GCU, XPU, DPU, INT, NIU None
2~2000 10
1~1000 4
30~100 95
30~100 60
30~100 50
30~100 60
30~100 50
30~100 60
30~100 50
30~100 85
30~100 70
30~100 70
30~100 60
30~100 80
30~100 70
30~100 90
30~100 75
30~100 95
30~100 85
30~100 95
30~100 85
30~100 95
30~100 85
30~100 85
30~100 70
30~100 90
30~100 80
30~100 95
30~100 80
1~100 60
1~100 5
30~100 80
30~100 70
30~100 60
30~100 50
30~100 70
30~100 60
30~100 85
30~100 75
30~100 90
30~100 85
30~100 60
30~100 50
2~2000 10
30~100 95
30~100 60
30~100 50
30~100 60
30~100 50
30~100 60
30~100 50
30~100 85
30~100 70
30~100 70
30~100 60
30~100 95
30~100 85
30~100 95
30~100 85
30~100 95
30~100 85
30~100 85
30~100 70
30~100 90
30~100 80
30~100 95
30~100 80
30~100 80
30~100 70
30~100 75
30~100 65
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
0~100 70
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
0~11 None
0~5, 8~27 None
0~31 None
0~31(AEUa), 0~335(AOUc) None
TS30, TS31 None
FRAATM, FRAIMA None
0~31 None
OFF, ON ON
0~1999 1
0~199 0
OFF, ON OFF
0~199 None
1024~65535 None
1024~65535 None

AUTO, PLAINTEXT, ENCRYPTED PLAINTEXT
YES, NO YES
0.0.0.0~255.255.255.255 None
21~65535 None
1024~65535 None
1024~65535 None
AUTO, PLAINTEXT, ENCRYPTED AUTO
DEFAULTPORT, CUSTOMPORT None
1024~65535 None
1024~65535 None
OFF, ON None
0~65534 None
RNC, NODEB, NRNC_RNC, NRNC_NODEB None
0~4095 None
0~65535 None
1~60 10
1~60 1
DEG, SEC DEG

MET, IMP MET
-90~90, step: 0.000001 None
-180~180, step: 0.000001 None
-1000~10000 None
-90:00:00.000~90:00:00.000 None
-180:00:00.000~180:00:00.000 None
-3281~32810 None
1~60 None
1~60 None
0~11 None
0~5, 8~27 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
ECHOREPLY, UNREACH, SOURCEQUENCH, REDIRECT,

ECHO, ROUTERADVERT, ROUTERSOLICIT, TIMXCEED,
PARAMPROB, TSTAMP, TSTAMPREPLY, IREQ,
IREQREPLY, MASKREQ, MASKREPLY None
0~11 None
0~5, 8~27 None
AEUa, AOUa, AOUc None
0~31(AEUa), 0~83(AOUa), 0~167(AOUc) None

1~32 1
0~255 None
D32, D64, D128, D256 D128
4~100(AEUa), 4~255(AOUa/AOUc) None
V1.0, V1.1 V1.1
OFF, ON ON
0~1999 1
3~505 None
0~199 0
OFF, ON OFF
0~199 None
0~11 None
0~5, 8~27 None
0~335 None
0~5, 8~27 None
0~31(AEUa), 0~83(AOUa), 0~167(AOUc) None
IU, IUB, IP_PATH, AL, GTPU, CELL_KPI,

SIGNALING_PLANE_LOOP, SHB None
AOUA, POUA, UOIA_ATM, UOIA_IP, FG2A, GOUA, GOUC,
POUC, FG2C, UOIC_ATM, AOUC, ALL None
AOUA, POUA, UOIA_ATM, UOIA_IP, FG2A, GOUA, AEUA,

PEUA, GOUC, POUC, FG2C, UOIC_ATM, AOUC, ALL None
OFF, ON None
10~100 None
1~10 None
10~100 None
1~10 None
1~10000 None
1~10000 None
1~100 None
1~10 None
1~20 None
1~20 None
1~20 None
1~5 None
OFF, ON OFF
60~3600 120
10~100 None
0~11 None
0~5, 8~27 None
FG2a, GOUa, FG2c, GOUc None

OFF, ON OFF
20~20000 1000
20~20000 800
OFF, ON OFF
0~11 None
0~5, 8~27 None
FG2a, GOUa, UOIa, FG2c, GOUc, POUc None
Hub, Leaf None

FG2a/GOUa/UOIa(IP) board:0~119;FG2c board:0~489,
512~767;GOUc board:0~499, 512~767;POUc(IP)
board:0~988, 1024~1535 None
ETHER, IPLOGICPORT, TRUNK, PPP, MP None
0~11 None
512~1535 None
0~11 None
0~499 None
0~167 None
0~3 None
OFF, ON None
64~100000, step:64 None
64~100000, step:64 None
0~100 25
64~100000, step:64 None
4500~32767 4500
0~100 0
0~100 96
0~1000 5
100~10000, step:100 10
1~100 5
100~1000 120
0~1, step:0.001 30
100~10000, step:100 2
0~10000 25
1~100 1
0~100 4
0~15 8
0~15 3
OFF, ON ON
0~1999 0
20~99 20
20~99 30
0~199 2
OFF, ON OFF
0~199 None
FPMUX, UDPMUX None
0~4599 None
0~65535 None
NO, YES None
BE, AF11, AF12, AF13, AF21, AF22, AF23, AF31, AF32,

AF33, AF41, AF42, , AF43, EF None
16~1023 352
24~1031 1031
1~30 2
NORTPCOMP, RTPCOMP None
NORTPCOMP, RTPCOMP None
0~12999 None
FPMUX, UDPMUX None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
IMA, UNI, FRAATM, NCOPT, ATMLOGICPORT, NULL None
{0~5}, {8~27} None
0~167 None
0~335 None
0~31 None
0~7 None
0~767 None
0~4095 None
32~65535 None
100~1999 None
100~1999 None
IUB, IUPS, OTHER None
0~4599 None
0~65535 None
IP, HYBRID_IP None
QoS, BE, AF11, AF12, AF13, AF21, AF22, AF23, AF31, AF32,
AF33, AF41, AF42, AF43, EF, LQ_QOS, LQ_BE, LQ_AF11,
LQ_AF12, LQ_AF13, LQ_AF21, LQ_AF22, LQ_AF23,
LQ_AF31, LQ_AF32, LQ_AF33, LQ_AF41, LQ_AF42,
LQ_AF43, LQ_EF None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 255.255.255.255
1~3000000 None
1~3000000 None
NULL, IPLGCPORT, RSCGRP NULL
0~5, 8~27 None
0~988 None
0~2047 None
0~199 2
DISABLE, ENABLE DISABLE
2~4094 None
ENABLED, DISABLED DISABLED
0.0.0.0~255.255.255.255 None
1~60 5
1~5 5
44~1024 64
UDP, ICMP ICMP
0~4599 None
0~65535 None
0~11 None
0~5, 8~27 None

0~31(FG2a/GOUa), 0~511(FG2c/GOUc) None
0~11 None
0~5, 8~27 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
HIGH, LOW None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~511 None
0~11 None
0~27 None
NORMAL, FORCE None
90~99 90
70~95 70
UMTS None
NO, YES YES
0~3 None
0~100500 None
0~24000000 None
0~24000000 None
0~24000000 None
0~24000000 None
0~30 None
0~176400 None
0~30 None
0~176400 None
0~632400 None
PDCP, AMRC, TFOTRFO, INDIRECRETRY,
INTERRATDIRECRETRY, INTERRATREDIRECT, CBS,
CELLID, OTDOA, AGPS, PUC, INTRACELLLDB,
INTERCELLLDB, MULTIRAB, HCS, RABDOWNSIZING,
QCPE, INTERSERVICEHO, INTERLOADHO, IUQOSRENEG,
LCSCZ, HSDPA, IUFLEX, IUBSC, IUBIP, MBMS None
WBAMR, HSUPA, RANSHARE, HSDPA3.6M, HSDPA7.2M,

ROHC, IURLC, NACC, PSHBUG, IMSIBH,
32HSDPAUPERCELL, 64HSDPAUPERCELL,
STMTRAONHSDPA, HSDPASTATETRAN, HSDPADRD,
ENHANCEDIUFLEX, STMTRAONHSUPA,
ATMIPDUALSTACK, IPTRANINIUR, IPTRANINIU,
FRACTIONALIP, IPIUBOVERBOOKING, FRACTIONALATM,
ATMOVERBOOKING, IUBHYBRIDIPTRAN,
MBMS8CHANNELPERCELL, 256KBPSCHNLRATEONMBMS,
MBMSFLCFLD, VTFTSFIHO, CBIHBUMTSANDGSMGPRS,
SRNSRELOCATION, SRNSRWHHANDOVER None
SRNSRWCUPDATE, LOSSLESSSRNSRELCT,
INTERFREQHARDHNDV, IMPRVEDWNLNKCVRGE,
ACRWHENSPUOVER, CBWHENIUIFAULT,
3G2GCOMMON_LOAD, FP_MUX, HSDPA_OVER_IUR,
HS_DPCCH_PREAMBLE_SUPPORT, HSUPA_2ms_10ms,
HSUPA_5_74MBPS, HSUPA_OVER_IUR,
HUB_IUB_OVERBOOKING, IMS_SIGNALING_OVER_HSPA,
DYN_BANDWIDTH_CTROL_IUB_IP, MBMS_OVER_IUR,
MBMS_P2P_OVER_HSDPA,
MBMS_ENHANCED_BROADCAST,
MBMS_ADMISSION_ENHANCE,
RAN_SHARING_ENHANCED_PACKAGE,
SRB_OVER_HSDPA, SRB_OVER_HSUPA, MULTI_FBNM,
HSDPA_13_976MBPS, BFD_ARP_IP, INTER_FHHBDLQOS,
INTER_RHBDLQOS, MBMS_16_CHANNELS_PER_CELL,
60_HSUPA_USERS_PER_CELL, TPMT, AQM None
DYNAMIC_POWER_ESTIMATION_FOR_MTCH,
ONE_TUNNEL, MULCAR_SWOFF_BASEDON_TRALOAD,
CS_OVER_HSPA, VOIP_OVER_HSPA,
96_HSDPA_USERS_PER_CELL,
HSPA_DOWN28_PER_USER, HSPA_DOWN21_PER_USER,
96_HSUPA_USERS_PER_CELL, MSCH_SCHEDULING,
MBMS_CHANNEL, ENHANCED_CELL_FACH,
CPC_HS_SCCH, CPC_DTX_DRX,
UPLINK_MACRO_RECEIVE, DOMAIN_ACCESS_CONTROL,
SERVICE_IN_RRC, TCP_ACCELERATOR,
UPLINK_CONTROL_OF_USER, MOCN_PACKAGE,
IUCS_UDP_MUX, RNC_NODE_REDUNDANCY,
DOWNLNK_ENHANCED_L2,
DIFF_SERVICE_ON_SPI_WEIGHT,
HSUPA_ADAPTIVE_RETRANSMISSION,
SIMPLE_CELL_BORADCAST, SATELLITE_TRANS_ON_IU,
IUR_G_NACC, IUR_G_LBB, IUR_G_SDB None
IUR_G_HBL, EHSPA_42M_DL, UL_MOBILITY_P1,
HSDPA_128_UPC, HSUPA_128_UPC, IUPC_FOR_LCS,
MULTI_FREQ_BNM_EH, WARN_OF_DISASTER,
QUAL_IMPROVE_FOR_SS, TTI_FOR_BE_SBC,
INTERSYS_REDIRECT_BOD, MEASUREMENT_BD_RETRY,
FAST_DORMANCY_ENHANCE,
HSUPA_COVERAGE_ENHANCE,
ENHANCE_UL_FOR_CELL_FACH, ENHANCE_DRX,
HSPA_DL84M_PER_USER, HSPA_UL11.5M_PER_USER,
PS_SERVICE_REDIRECT_FU2L,
VIDEO_PHONE_RESTRICT,
OPT_R99HSUPA_USER_FAIRNESS,
ADAPTIVE_CONF_TC_PO_HSUPA,
WEB_BROWSING_ACCELERATION,
P2P_RATE_CONTROL,
FREE_USER_RESOURCE_RESERVE,
FLEX_HSPA_TECH_SELECTION None
ON, OFF None
1~63 None
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 100
0~100 0
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 30
0~100 100
0~100 0
0~100 0
LFB, CL None
monitor, host_gate, ems_gate, authority, configure, maintain,

stat, alarm, software, ftp_server, sntp, ems_agent,
omu_manager, weblmt, cfa, debug_log None
TASKID, CMDCODE None
0~65535 None
0~65535 None
7~365 30
10000~50000 50000
OPLOG_TYPE, SECLOG_TYPE None
0~186 None
0~186 None
0~186 None
M3UA_SGP, M3UA_IPSP, M3UA_SS7SP, M3UA_SP None
0~4294967295 4294967295
0~186 None
0~4 None
M3UA_ASP, M3UA_IPSP None
0~4294967295 4294967295
0~186 None
0~186 None
B0000, B0001, B0010, B0011, B0100, B0101, B0110, B0111,

B1000, B1001, B1010, B1011, B1100, B1101, B1110, B1111 B1111
M3UA_OVERRIDE_MOD, M3UA_LOADSHARE_MOD M3UA_LOADSHARE_MOD

M3UA_ASP, M3UA_IPSP M3UA_ASP
1~10 5
0~186 None
0~15 None
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None

0~7 None
0~1199 None
0~99 0
M3UA_MASTER_MOD, M3UA_SLAVE_MOD M3UA_MASTER_MOD
0~186 None
0~186 None
0~99 0
MEASRST, HOSTRST None
0~14 7
500~5000(MEASRST), 500~2000(HOSTRST) None
0~11 None
0~5, 8~27 None

PEUa, POUa, POUc None
IP IP
0~31(PEUa), 0~63(POUa), 0~167(POUc) None
MLPPP, MCPPP MCPPP
NO, YES None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
LONG, SHORT LONG
4, 8 None
128~1024 256
No_HC, UDP/IP_HC, RTP/UDP/IP_HC UDP/IP_HC
Disable, Enable Enable
Disable, Enable Disable
1~746 None
1~1500 None
1~1500 None
OFF, ON ON
0~1999 0
0~100 0
NO_V, PAP_V, CHAP_V NO_V
SERVER, CLIENT None
0~199 2
OFF, ON OFF

OFF, ON OFF
ERR_PFM_5E6, ERR_PFM_1E5, ERR_PFM_5E5,

ERR_PFM_5E3 None
ERR_PFM_1E3 None
OFF, ON OFF
0~199 None
4, 8 8
1~746 64
1~1500 256
1~1500 1000

ERR_PFM_5E3 ERR_PFM_1E5
ERR_PFM_1E3 ERR_PFM_5E6
0~11 None
0~5, 8~27 None
PEUa, POUa, POUc None
0~31(PEUa), 0~63(POUa), 0~167(POUc) None
0~499 None
0~31(PEUa), 0~125(E1 of POUa), 0~167(T1 of POUa),

0~251(E1 of POUc), 0~335(T1 of POUc) None
TS30, TS31 None
2~5 3
1~30 2
None, 16bit, 32bit 16bit
0~11 None
0~27 None
0~11 None
0~27 None
0~11 None
0~27 None
0~7 None
NON-REVERTIVE, REVERTIVE None
30~60000 None
NOT-INDICATE-END, INDICATE-END None
1E-3, 1E-4, 1E-5, 1E-6, 1E-7, 1E-8, 1E-9 1.00E-06
HIGH, LOW None
MODE1, MODE2, MODE3, MODE4 None
0~11 None
0~27 None
0~7 None
CLEAR, LOP, FS, MS, EXERS None
0~186 None
0~186 None
B0000, B0001, B0010, B0011, B0100, B0101, B0110, B0111,

B1000, B1001, B1010, B1011, B1100, B1101, B1110, B1111 B1111
OFF, ON OFF
0~186 None
0~15 None
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~1399 None
0~99 0
1~15 10
1~254 170
0~186 None
0~186 None
0~99 0
800~1200 1200
1400~2000 2000
800~1200 1200
800~1200 1200
800~1200 1200
800~1200 1200
30000~60000 60000
800~1500 1500
800~1500 1500
2000~3000 3000
800~1500 1500
180000~360000 360000
180000~360000 360000
8000~12000 12000
30000~90000 60000
35000~120000 35000
0~186 None
0~4 None
WNF, DNF None
1~16383(BIT14), 1~65535(BIT16), 1~16777215(BIT24) None
IUCS, IUPS, IUR, IUCS_RANAP, IUCS_ALCAP, STP,

AAL2SWITCH, IUPC None
B0000, B0001, B0010, B0011, B0100, B0101, B0110, B0111,

B1000, B1001, B1010, B1011, B1100, B1101, B1110, B1111 B0000
NO, YES YES
OFF, ON OFF
MTP3, M3UA, MTP3_M3UA None
M3UA_FIRST, MTP3_FIRST None
ITUT, ANSI, TTC ITUT
ALL, BOARD, PORT, DSP None
0~11 None
0~27 None
0~335 None
0~27 None
ALL, ONEBYONE None
1~65535 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
Administrators, Operators, Users, Guests, Customs Guests
G_0, G_1, G_2, G_3, G_4, G_5, G_6, G_7, G_8, G_9, G_10,
G_11, G_12, G_13, G_14, G_15, G_16, G_17, G_18, G_19,
G_20, G_21, G_22, G_23, G_24, G_25, G_26, G_27, G_28,
G_29, G_30, G_31 None
NOLIMIT, LIMIT NOLIMIT
2000-1-1~2037-12-31 None
2000-1-1~2037-12-31 None
00:00:00~23:59:59 None
00:00:00~23:59:59 None
SUN, MON, TUE, WED, THU, FRI, SAT None
Administrators, Operators, Users, Guests, Customs None

NOLIMIT, LIMIT None
NOLIMIT, LIMIT None
0~4 None
INT, INTB, NAT, NATB None
BIT14, BIT16, BIT24 None
WNF, DNF None
1~16383(BIT14), 1~65535(BIT16), 1~16777215(BIT24) None
OFF, ON OFF
OFF, ON ON
0~199 None
ONE, TWO, THREE, FOUR None
ATM, IP None
UMTS UMTS
0~3 None
0~100 None
0~199 None
0~3 None
0~100 None
0~199 None
0~3 None
0~100 None
0~199 None
0~3 None
0~100 None
0~199 None
OFF, ON ON
0~11 None
0~5, 8~27 None
AOUa~5 POUa~6 UOIa~7 AOUc~13 UOIc~15 POUc~14 None
ALL, SINGLE None
0~1(AOUa/POUa), 0~3(UOIa/AOUc/POUc), 0~7(UOIc) None
OFF, ON None
SDH, SONET None
LUCENT_MODE, HUAWEI_MODE, ALCATEL_MODE None
UNI, NNI None
NULL, 1byte, 16byte, 64byte None
Hexadecimal, Character_String Character_String

0~15 None

O1E11_R1E12 None
O1E11_R1E12 None

O1E7_R1E8, O1E8_R1E9, O1E9_R1E10, O1E10_R1E11 None

O1E7_R1E8, O1E8_R1E9, O1E9_R1E10, O1E10_R1E11 None
OFF, ON None
0~1999 None
ZERO, SPACE None
AU4, AU3 None
0~11 None
0~5, 8~27 None

0~7 None
NO_LOOP, REMOTE_LOOP, LOCAL_LOOP None
One_touch, Step_by_Step Step_by_Step
SCUa, SCUb, GCUa, GCGa, PEUa, AEUa, FG2a, GOUa,

AOUa, POUa, UOIa, AOUc, POUc, UOIc, FG2c, GOUc, SPUa,
SPUb,
DPUb, DPUe, NIUa None
UCP, RUCP, UUP, ATM, IP, NIU None
MAINCPU_PATCH, DSP_PATCH, UCODE_PATCH None
0~11 None
0~5, 8~27 None

BE, AF11, AF12, AF13, AF21, AF22, AF23, AF31, AF32,
AF33, AF41, AF42, AF43, EF None
0~63 48
10~1999 None
IP, ATM None
0~5 2
10~150 25
10~150 15
10~150 60
10~150 25
10~150 15
10~150 60
10~150 25
10~150 15
10~150 60
10~150 25
10~150 15
10~150 60
10~150 50
10~150 25
10~150 80
10~150 50
10~150 25
10~150 80
0~11 None
0~5, 8~27 None
PEUa, POUa, UOIa, POUc None
IP IP
0~499 None
0~335 None
TS30, TS31 None
NO, YES None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
No_HC, UDP/IP_HC, RTP/UDP/IP_HC UDP/IP_HC

1~746 64
1~1500 256
1~1500 1000
NO_V, PAP_V, CHAP_V NO_V
SERVER, CLIENT None
2~5 3
1~30 2
OFF, ON ON
0~100 0
0~1999 0
None, 16bit, 32bit 16bit
0~199 2
OFF, ON OFF

OFF, ON OFF
0~199 None
1~1500 1000
0~11 None
0~5, 8~27 None

PPP, MPGRP None
0~167 None
0~499 None
NO_LOOP, SELF_LOOP None
1~65535 None
6~32 characters 8
LOWERCASE-1&UPPERCASE-
LOWERCASE, UPPERCASE, DIGIT, SPECHAR 1&DIGIT-1&SPECHAR-0
1~255 3
1~65535 30
1~60 5
1~999 90
1~255 5
1~10 5
2~32 2
ON, OFF OFF
0~11 None
BIT0, BIT1, BIT6, BIT7, BIT8, BIT9, BIT14, BIT15, BIT16,
BIT17, BIT22, BIT23, BIT24, BIT25, BIT29, BIT30, BIT31 None
BIT0, BIT1, BIT2, BIT3, BIT4, BIT5, BI16, BIT7, BIT8, BIT9,
BIT10, BIT11, BIT12 None
0~11 None
55~59 57
40~45 43
55~59 57
40~45 43
55~59 57
40~45 43
55~59 57
40~45 43
55~59 57
40~45 43
55~59 57
40~45 43
0~11 None
0~5, 8~27 None
0~63 None
0~63 None
0~63 None
0~63 None
0~63 None
OFF, ON None
0~63 None
OFF, ON None
SINGLE, ALL None

0~65535 None
ASC0, ASC1, ASC2, ASC3, ASC4, ASC5, ASC6, ASC7 ASC0
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~2047 None
ATM, IP None
NO, YES None
0~2047 None
0~3 None
FULL_DUPLEX, HALF_DUPLEX None
0~4000000 None
0~4000000 None
0~4000000 None
0~199 0
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~1399 None
UNI, IMA, FRAATM, NCOPT, ATMLOGICPORT, NULL None
0~11 None
0~5, 8~27 None
0~335 None
0~167 None
0~31 None
0~7 None
0~767 None
0~4095 None
32~65535 None
100~1999 None
100~1999 None
UNI, NNI None
MPS_NORMAL, MPS_EMERGENCY, MPS_NEUTRAL MPS_NEUTRAL
700~1000(UNI), 100~1000(NNI) None
500~10000(UNI), 90~500(NNI) None
10000~30000(UNI), 100~30000(NNI) None
5000~20000(UNI), 1200~20000(NNI) None
1000~3000(UNI), 100~1200(NNI) None
1~7 2
30~90 30
10~200 10
45~90 60
1200~2000 1500
0~10 0
4~8 4
25~50(UNI), 250~500(NNI) None

3~67 67
10~2000 100
1~32767 None
60~120 90
60~600 90
180~1260 720
10~20 15
10~20 15
30~90 60
1380~1500 1440
10~20 15
10~20 20
30~90 60
60~120 90
30~90 60
10~50 30
10~20 10
10~20 15
1~30 None
1~30 None
DISABLED, ENABLED ENABLED
0~65535 None
0~255 5
-35~15, step: 0.1 0
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~1199 None
SERVER, CLIENT None
NBAP, M3UA None
0~63 48
1024~65535 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
1024~65535 None
NO, YES None
0~5, 8~27 None
0~988 None
50~60000 None
50~60000 3000
50~60000 1000
0~100 12
0~100 25
0~500 None
1000~600000 None
0~254 None
0~254 None
NO, YES NO
NO, YES NO
ALDER32, CRC32 CRC32
500~1500 800
2~4094 None
2~4094 None
UNAVAILABLE, AVAILABLE UNAVAILABLE
NO, YES YES
1~254 10
YES, NO NO
1000~600000 5000
0~254 10
0~254 5
1024~65535 58080
1024~65535 2905
1024~65535 58000
0~11 None
6~7 None
0~11 None
CLOSE, OPEN None
XPU None
30~100 70
30~100 60
30~100 85
30~100 75
30~100 90
30~100 80
30~100 75
30~100 65
30~100 75
30~100 65
30~100 75
30~100 65
ON, OFF ON
ON, OFF ON
ON, OFF ON
ON, OFF ON
1~60 60
0.0.0.0~255.255.255.255 None
123~65534 None
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
NONE, PEER NONE
1~30 None
1~50 None
Valid command string, without the ';'at the end of the string. None
0~19 None
1~124, 128~189 None
1~11 None
NO, YES NO
SCUa, SCUb SCUa
PARC, PARCb PARC
0~11 None
1~30 None
1~50 None
DISABLED, ENABLED ENABLED
Valid command string, without the ';'at the end of the string. None
ONTIME, DAILY_T, DAILY_C, WEEKLY_T, WEEKLY_C,

MONTHLY_T, MONTHLY_C None
2000-1-1~2037-12-31 None
2000-1-1~2037-12-31 None
1~100 1
MON_1~MON_31 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
1~1440 30
00:00~23:59 None
DISABLED, ENABLED None
2000-1-1~2037-12-31 None
2000-1-1~2037-12-31 None
1~100 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
1~1440 None
00:00~23:59 None
1~250 characters MBSC
1~250 characters BSC
0~255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None

2000-1-1~2037-12-31 None
00:00:00~23:59:59 None
OFF, ON ON
OFF, ON ON
OFF, ON ON
OFF, ON ON
OFF, ON ON
OFF, ON ON
OFF, ON ON
OFF, ON OFF
OFF, ON ON
OFF, ON ON
0~11 None
OFF, ON None
OFF, ON None
OFF, ON None
OFF, ON None
OFF, ON None
OFF, ON None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
0~4294967295 None
{0~4294967295} None
1~33 None
0~100 70
0~100 70
0~100 15
0~100 15
0~100 100
0~100 15
0~100 15
0~100 70
0~100 70
0~100 100
0~100 100
0~100 100
0~100 100
0~100 70
0~100 70
0~100 100
0~100 100
0~100 40
0~100 40
0~100 40
0~100 40
0~100 15
0~100 15
0~100 70
0~100 70
0~100 100
0~100 40
0~100 40
0~100 15
0~100 15
0~100 70
0~100 70
0~100 100
0~100 40
0~100 40
0~100 20
0~100 20
0~100 20
10~199 None
ATM, IP None
PERCENTAGE, BANDWIDTH None
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~200000 0
0~100 5
0~100 5
0~100 15
0~100 15
0~100 20
0~100 20
0~100 0
0~100 0
0~100 1
0~100 1
14~163 None

AF21, AF22, AF23, AF31, AF32, AF33, AF41, AF42, AF43,
EF, LQBE, LQAF11, LQAF12, LQAF13, LQAF21, LQAF22,
LQAF43, LQEF None

LQAF43, LQEF, NULL None

LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None


LQAF43, LQEF None

LQAF43, LQEF None

0~11 None
0~5, 8~27 None
0~335 None
TS30, TS31 None
0~335 None
TS30, TS31 None
0~65535 None
09:00), GMT-0800(GMT-08:00), GMT-0700(GMT-07:00),
03:30), GMT-0300(GMT-03:00), GMT-0200(GMT-02:00),
GMT-0100(GMT-01:00), GMT(GMT), GMT+0100(GMT+01:00),
GMT+0200(GMT+02:00), GMT+0300(GMT+03:00),
GMT+0330(GMT+03:30), GMT+0400(GMT+04:00),
GMT+0430(GMT+04:30), GMT+0500(GMT+05:00),
GMT+0530(GMT+05:30), GMT+0545(GMT+05:45),
GMT+0600(GMT+06:00), GMT+0630(GMT+06:30),
GMT+0700(GMT+07:00), GMT+0800(GMT+08:00),
GMT+0845(GMT+08:45), GMT+0900(GMT+09:00),
GMT+0930(GMT+09:30), GMT+1000(GMT+10:00),
GMT+1030(GMT+10:30), GMT+1100(GMT+11:00),
GMT+1130(GMT+11:30), GMT+1200(GMT+12:00),
GMT+1245(GMT+12:45), GMT+1300(GMT+13:00),
GMT+1400(GMT+14:00) GMT+0800
YES, NO NO
DATE, WEEK, DATEWEEK None
JAN, FEB, MAR, APR, MAY, JUN, JUL, AUG, SEP, OCT,
NOV, DEC None
1~31 None
FIRST, SECOND, THIRD, FOURTH, LAST None
00:00:00~23:59:59 None
DATE, WEEK, DATEWEEK None
JAN, FEB, MAR, APR, MAY, JUN, JUL, AUG, SEP, OCT,
NOV, DEC None
1~31 None
FIRST, SECOND, THIRD, FOURTH, LAST None
00:00:00~23:59:59 None
-120~-1, 1~120 None
0~4095 None
0~65535 None
0~65535 None
-50~50 0
-50~50 0
-115~-25, step:2 Actual value = -115 + (58 + GUI value) * 2 -50
0, 10, 20, 30, 40, 50, 60 D0
3, 6, 9, 12, 15, 18, 21, INFINITY D3
FALSE, TRUE 0
0~30 None
-24~0 -18
FALSE, TRUE 1
FALSE, TRUE 0
FALSE, TRUE 0
0~31 None
FALSE, TRUE 0
0~15 0
OFF, ON OFF
OFF, ON OFF
0.1~1, step:0.1 2
10~360000, step:10 50
6~3600 10
1~3600 1
NOPRIORITY, GOLD, SILVER, COPPER None
0~1, step: 0.01 10
0~1, step: 0.01 10
0~1, step: 0.01 50
0~1, step: 0.01 50
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 10
0~1, step: 0.01 10
0~1, step: 0.01 10
0~1, step: 0.01 10
0~1, step: 0.01 100
0~1, step: 0.01 None
0~1, step: 0.01 100

0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~1, step: 0.01 100
0~65535 None
0~255 4
0~255 6
0~1 1
TRUE, FALSE 0
0~65535 None
-22~5 -6
30~100 70
20~99 60
30~100 80
20~99 70
0~55.9, step: 0.1 50
0~55.9, step: 0.1 50
0.1~56, step: 0.1 120
0.1~56, step: 0.1 120
1~64000 1000
1~4294967295 3000
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
0~55.9, step: 0.1 50
0~55.9, step: 0.1 50
0.1~56, step: 0.1 120
0.1~56, step: 0.1 120
1~64000 1000
1~4294967295 3000
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
ON, OFF OFF

ON, OFF OFF
ONE, TWO, THREE, FOUR None

Band9 None
0~16383 None
0~511 None
0~511 None

Band9 None
0~16383 None
0~511 None
0~511 None

Band9 None
0~16383 None
0~511 None
0~511 None

Band9 None
0~16383 None
0~511 None
0~511 None
ON, OFF OFF
0~7 None
0~7 None
0~7 None
0~7 None
GSM900_DCS1800_BAND_USED, PCS1900_BAND_USED None
0~1023 None
0~1023 None
0~65535 None
0~255 0
-35~15, step: 0.1 -20
NODEB_CREDIT_CAC_SWITCH None
RSVDBIT1, RSVDBIT2, RSVDBIT3, RSVDBIT4, RSVDBIT5,
RSVDBIT11, RSVDBIT12, RSVDBIT13, RSVDBIT14,
RSVDBIT15, RSVDBIT16 None
0~4294967295 0
0~4294967295 0
SYS_LEVEL, NODEB_LEVEL, CELL_LEVEL None
OFF, ON ON
1~5 3
1~500 180
1~500 60
1~500 60
1~500 100
1~200 60
1~200 20
1~200 20
1~100 45
1~100 15
1~100 15
MBR, Category, Min, Max Min
0~256000 128
0~256000 384
0~256000 512
0~256000 1000
0~256000 2000
0~256000 4000
0~256000 8000
0~256000 16000
0~256000 32000
0~64000 128
0~64000 384
0~64000 512
0~64000 768
0~64000 1000
0~64000 1500
0~64000 2500
0~64000 5500
0~64000 7500
0~11 None
{0}, {2}, {4}, {8}, {10}, {12}, {14}, {16}, {18}, {20}, {22}, {24}, {26} None
0~3 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~127 None
0~3 None
LAC, RNC, CELL None
1~65533, 65535 None
0~65535 None
0~127 None
0~199 None
0~999 None
CellImmediate,
PLMNNormal,
SANormal,
CellNormal None
High, Background, Normal, Default, Butt Normal
1~4096 1
0~65535 10
English, Italian, French, Spanish, Dutch, Swedish, Danish,

Portuguese, Finnish, Norwegian, Greek, Turkish, Hungarian,
Polish, UCS2 None
0~127 None
Earthquake, Tsunami, Hurricane, Other None

chars with length of 0~80 None
chars with length of 0~80 None
0~65535 None
SAAL, SCTP, SAAL-SCTP None
0~1399 None
0~1199 None
SAAL, SCTP SAAL
ATMTODUAL, IPTODUAL, DUALTOATM, DUALTOIP None
SAAL, SCTP None
FIXED, CYCLE None

5~255 30
0~65535 None

0~50, step: 0.1 430

Band9, BandIndNotUsed None
Valid, Invalid Invalid
0~65535 None
0~31 None
TRUE, FALSE None

0~16383 None
0~16383 None

CHIP1536, CHIP1792, CHIP2048, CHIP2304 None
1~256 5
1~256 50
0~25.5, step: 0.1 50
0~511 None
TRUE, FALSE None

1~8 None
0~268435455 None
{1~65533}, {65535} None
0~65535 None
NOT_REQUIRE, REQUIRE None
0~255 None
STTD_Supported, STTD_not_Supported STTD_not_Supported
CP1_Supported, CP1_not_Supported CP1_not_Supported
OFFSET1, OFFSET2 OFFSET1
None, STTD, CP1 None
None, STTD None
None, STTD None
None, STTD None

-10~10, step: 0.5 0
TRUE, FALSE 0
TRUE , FALSE 0
0~500 430
{1~8}, {255} 255
D1, D2, D3, D4, D5, D6, D7, D8 None
0~65535 None
0~65535 None
0~65535 None
0~65535 None
0~65535 None
0~65535 None
0~65535 None
0~65535 None
TRUE, FALSE 0
0~3 None
0~65535 None
-10~50, step: 0.1 330
-100~500 330
-35~15, step: 0.1 -50
-35~15, step: 0.1 -50
-35~15, step: 0.1 0
-35~15, step: 0.1 -20
0~65535 None

0~268435455 None
FALSE, TRUE None
-10~50, step: 0.1 330
-10~50, step: 0.1 346
-10~50, step: 0.1 313
-35~15, step: 0.1 -30
-35~15, step: 0.1 -30
-35~15, step: 0.1 0
-35~15, step: 0.1 -130
-10~5 -7
0~65535 None
RESERVED, NOT_RESERVED NOT_RESERVED
BARRED, NOT_BARRED NOT_BARRED

BARRED, NOT_BARRED None
ALLOWED, NOT_ALLOWED ALLOWED
10, 20, 40, 80, 160, 320, 640, 1280 D320

BARRED, NOT_BARRED None
ALLOWED, NOT_ALLOWED NOT_ALLOWED
10, 20, 40, 80, 160, 320, 640, 1280 D1280
0~65535 None
{1~65533}, {65535} None
0~65535 None
0~255 None
0~65535 None
CRD_ADCTRL, HSDPA_UU_ADCTRL,
HSUPA_UU_ADCTRL, MBMS_UU_ADCTRL,
HSDPA_GBP_MEAS, HSDPA_PBR_MEAS,
HSUPA_PBR_MEAS, HSUPA_EDCH_RSEPS_MEAS,
EMC_UU_ADCTRL, RTWP_RESIST_DISTURB,
FACH_UU_ADCTRL, MIMOCELL_LEGACYHSDPA_ADCTRL,
FAST_DORMANCY_ADCTRL None
ALGORITHM_SECOND, ALGORITHM_THIRD None
ALGORITHM_SECOND, ALGORITHM_THIRD None
INTRA_FREQUENCY_LDB, PUC, UL_UU_LDR,

DL_UU_LDR, UL_UU_OLC, DL_UU_OLC,
OLC_EVENTMEAS, CELL_CODE_LDR, CELL_CREDIT_LDR,
UL_INTRA_FREQUENCY_ULB None
ALGORITHM_REQUIRED, ALGORITHM_DEPEND_ON_LCG ALGORITHM_DEPEND_ON_LCG

64QAM, MIMO, E_FACH, DTX_DRX,
HS_SCCH_LESS_OPERATION, DL_L2ENHANCED,
64QAM_MIMO, UL_16QAM, DC_HSDPA, UL_L2ENHANCED,
EDPCCH_BOOSTING, DCMIMO_HSDPA, E_DRX None
E_F_DPCH_OFF, E_F_DPCH_ON E_F_DPCH_OFF
TX_DIVERSITY_ON_TO_OFF,
TX_DIVERSITY_OFF_TO_ON None
NBM_LDC_ALL_UE, NBM_LDC_MATCH_UE_ONLY,
NBM_LDC_MATCH_UE_FIRST NBM_LDC_MATCH_UE_ONLY

0~4294967295 0
0~4294967295 0
OFF, ON OFF
OFF, ON OFF
0~65535 None
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
4.75, 5.15, 5.90, 6.70, 7.40, 7.95, 10.20, 12.20 NBAMR_BITRATE_12.20K
0~65535 None
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
6.60, 8.85, 12.65, 14.25, 15.85, 18.25, 19.85, 23.05, 23.85 WBAMR_BITRATE_23.85K
0~65535 None
TU, RA, HT TU
0~1, step:0.01 75
0~1, step:0.01 75
0~1, step:0.01 60
0~1, step:0.01 80
0~1, step:0.01 80
0~1, step:0.01 75
0~1, step:0.01 80
0~1, step:0.01 85
0~1, step:0.01 83
0~1, step:0.01 90
0~1, step:0.01 0
0~1, step:0.01 0
1~200 95
1~200 80
0~1, step:0.01 100
0~1, step:0.01 100
0~1, step:0.01 100
0~1, step:0.01 0
0~1, step:0.01 70
0~1, step:0.01 30
0~128 64
-50~33 24
-50~33 24
-50~33 24
-50~33 24
-112~-50, step:0.1 61
-30~30 -13
OFF, ON ON
1~6000 120
0~10 0
0~128 20
0~1, step:0.01 0
0~1, step:0.01 0
0~1, step:0.01 20
0~63 16
0~1, step:0.01 60
0~63 40
SF4, SF8, SF16, SF32, SF64, SF128, SF256, SFOFF SF16
SF4, SF8, SF16, SF32, SF64, SF128, SF256, SFOFF SF32

hour{0~23}, min{0~59}, sec{0~59} None
hour{0~23}, min{0~59}, sec{0~59} None
0.1~10, step:0.1 5
0.1~40, step:0.1 100
0~48 48
0~1, step:0.01 40
0~48 48
0~1, Step: 0.01 20
0~1, step:0.01 100
0~1, step:0.01 100
0~65535 None
0~65535 None
0~3 None
0~65535 None
OFF, ON OFF
0~65535 None
HIGH_SPEED_AND_HIGH_COVERAGE_CELL, WALKING_SPEED_AND_HOT_S
OTHER_CELL POT_CELL
8, 16, 32, 64, 128, 256 D64
8, 16, 32, 64, 128, 256 D64
0~65535 None
0~10, step: 0.1 10
0~10, step: 0.1 20
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384 D64
0~65535 None
OFF, ON OFF
0~765, step: 3 255
0~100 50
0~100 0
0~65535 None
0~5 2
ON, OFF OFF
ON, OFF OFF
ON, OFF OFF
Power, UserNumber UserNumber
0~100 35
0~100 100
ON, OFF OFF
SF4, SF8, SF16, SF32, SF64, SF128, SF256 SF8
0~100 13

Band9, DependOnNCell, BandIndNotUsed DependOnNCell
TRUE, FALSE None

0~16383 None
0~16383 None
ON, OFF OFF
0~100 25
ON, OFF OFF
0~65535 None
ON, OFF OFF
ON, OFF OFF
0~30 10
0~30 10
0~30 25
0~30 17
0~30 15
0~30 25
0~30 20
0~30 15
0~65535 None
0~3 None
FALSE, TRUE None
FALSE, TRUE None
RestrictionFixed, RestrictionFlexible None

AC0, AC1, AC2, AC3, AC4, AC5, AC6, AC7, AC8, AC9, AC10,
AC11, AC12, AC13, AC14, AC15 None
1~16 None
6~3600 None
0~65535 None
OFF, ON_1, ON_2, ON_3 None

00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
00:00~23:59 None
FORCESHUTDOWN, CONDITIONALSHUTDOWN,
QOSSHUTDOWN CONDITIONALSHUTDOWN
0~15 1
0~15 0
0~15 0
0~1, step:0.01 20
SPI1, SPI2, SPI3, SPI4, SPI5, SPI6, SPI7, SPI8, SPI9, SPI10,
SPI11, SPI12, SPI13, SPI14, SPI15 None
0~65535 None
EDRXT321_100, EDRXT321_200, EDRXT321_400,

EDRXT321_800 EDRXT321_100
EDRXCYCLE_4, EDRXCYCLE_8, EDRXCYCLE_16,

EDRXCYCLE_32 EDRXCYCLE_8
EDRXBURST_1, EDRXBURST_2, EDRXBURST_4,

EDRXBURST_8, EDRXBURST_16 EDRXBURST_1
INTERRUPTION_CFG, INTERRUPTION_NOT_CFG INTERRUPTION_CFG
0~65535 None
-35~15, step:0.1 10
-35~15, step:0.1 -30
-35~15, step:0.1 0
1~1000 32
1~2000 512
1~1000 32
1~2000 512
1~1000 32
1~2000 512
1~1000 32
1~2000 512
1~1000 32
1~2000 512
1~1000 32
1~2000 512
1~1000 32
1~2000 512
0~65535 None
1~32 1
1~32 19
35~15, step:0.1 -30
35~15, step:0.1 15
1~5 2
0~1279 35
0~2559 10
1~2000 32
0~65535 None
8, 16 D8
8, 16 D8
FALSE, TRUE 0
-24.5~0, step: 0.5 41

0~65535 5000
TRUE, FALSE 0
1~15 None
0~4095 None
0~65535 None

TRUE, FALSE None
0~16383 None
0~16383 None
0~65535 None
INACTIVE, ACTIVE ACTIVE
0~65535 None
USED, NOT_USED NOT_USED

0~7 0
-105~91, step:2 0
-105~91, step:2 0
0~99 20
NOT_USED, 30, 60, 120, 180, 240 D60
1~16 8
NOT_USED, 10, 20, 30, 40, 50, 60, 70 D20
-32~20, step:2 0
0~65535 None
OFF, ON OFF
0~511 180
1~16 15
0~255 60
0~511 240
1~16 3
0~120 10
0~65535 None
INTERFREQ, INTERRAT, SIMINTERFREQRAT SIMINTERFREQRAT
COEXIST_MEAS_THD_CHOICE_INTERFREQ, COEXIST_MEAS_THD_CHOICE_
COEXIST_MEAS_THD_CHOICE_INTERRAT INTERFREQ
OFF, ON OFF
OFF, ON OFF
0~65535 None
Manual, Automatic Automatic
1~15 5
1~15 5
1~15 1
1~15 4
-50~0, step:0.1 0
-3~19, step:0.5 2.5dB
Mode0, Mode1 Mode0
OFF, ON ON
1~16 3
0~300 5
-3~19, step:0.5 2.5dB
0~65535 None
0~65535 None
5/15, 6/15, 8/15, 9/15, 12/15, 15/15, 19/15, 24/15, 30/15 PO_24/15
5/15, 6/15, 8/15, 9/15, 12/15, 15/15, 19/15, 24/15, 30/15 PO_24/15
1~4 1
1~4 1
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 2, 4, 8, 10, 20, 40, 80, 160 D8
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 4, 8, 10, 20, 40, 80, 160 D4
0~65535 None
1~8 1
1~8 1
0~1, step:0.01 75
0~1, step:0.01 0
0~4095 None
0~65535 None
0~65535 None
0~65535 None
PERIODICAL_REPORTING, EVENT_TRIGGER PERIODICAL_REPORTING
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
NON_PERIODIC_REPORT, 250, 500, 1000, 2000, 3000,

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D500
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~14.5, step:0.5 0
0~2, step:0.1 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0~64000 0
-24~0 -14
-24~0 -12
-24~0 -14
-24~0 -14
-24~0 -12
-24~0 -12
-115~-25 -95
-115~-25 -92
-115~-25 -95
-115~-25 -95
-115~-25 -92
-115~-25 -92
-24~0 -12
-24~0 -12
-24~0 -12
-115~-25 -92
-115~-25 -92
-115~-25 -92
-24~0 -12
-24~0 -12
-24~0 -12
-115~-25 -92
-115~-25 -92
-115~-25 -92
0~512 60
500~32000, step:500 1
0~62, 63: Infinity 4
0~1000 0
0~65535 None
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3

0~14.5, step:0.5 6
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
-24~0 -16
0~512 60
500~32000, step:500 4
0~65535 None
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
CPICH_EC/NO, CPICH_RSCP, AUTO AUTO
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~2, step:0.1 0

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D1000
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~7.5, step:0.5 4
0~7.5, step:0.5 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
0~64000, 65535 0
0~64000 0
REQUIRED, NOT_REQUIRE REQUIRED
-24~0 -14
-24~0 -12
-24~0 -15
-24~0 -15
-24~0 -13
-24~0 -13
-115~-25 -100
-115~-25 -97
-115~-25 -110
-115~-25 -110
-115~-25 -107
-115~-25 -107
lower than -110, -110~-48(Actual value meets the condition:

Actual Value = GUI Value - 111) 16

-24~0 -12
-24~0 -13
-24~0 -13
-115~-25 -97
-115~-25 -107
-115~-25 -107
0~512 60
0~65535 0
0~7.5, step:0.5 0
500~32000, step:500 1
0~63 3
0~65535 30
0~65535 None
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3

0~7.5, step:0.5 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640

1~16 16
0~512 60
0~100 80
0~100 60
500~32000, step:500 4
0~63 3
0~65535 30
0~4095 None
0~65535 None
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3

CPICH_EC/NO, CPICH_RSCP CPICH_EC/NO
1, 2, 4, 8, 16, 32, 64, INFINITY D16

8000, 16000 D4000
1, 2, 4, 8, 16, 32, 64, INFINITY D16

8000, 16000 D4000
1, 2, 4, 8, 16, 32, 64, INFINITY D64

8000, 16000 D1000
0~14.5, step:0.5 6
0~14.5, step:0.5 6
0~14.5, step:0.5 6
0~14.5, step:0.5 12
0~14.5, step:0.5 12
0~14.5, step:0.5 12
-24~0 -24
-115~-25 -115
0~7.5, step:0.5 0
0~7.5, step:0.5 0
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~2, step:0.1 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
-24~0 -24
1~6 3
-115~-25 -115
0~65535 None
0~10, step:0.1 2
0~1, step:0.01 90
0~1, step:0.01 30
0~65535 None
0~1, step:0.01 55
0~1, step:0.01 45
0~1, step:0.01 70
0~1, step:0.01 60
0~1, step:0.01 95
0~1, step:0.01 85
0~1, step:0.01 95
0~1, step:0.01 85
10~600000 1000
0~1, step:0.01 70
0~1, step:0.01 50
0~1, step:0.01 73
0~1, step:0.01 60
0~3, step: 0.01 150
0~65535 None
NoAct, InterFreqLDHO, BERateRed, QoSRenego,
CSInterRatShouldBeLDHO, PSInterRatShouldBeLDHO,
AMRRateRed, MBMSDecPower, CodeAdj,
CSInterRatShouldNotLDHO, PSInterRatShouldNotLDHO CodeAdj

CSInterRatShouldNotLDHO, PSInterRatShouldNotLDHO InterFreqLDHO

CSInterRatShouldNotLDHO, PSInterRatShouldNotLDHO BERateRed

CSInterRatShouldNotLDHO, PSInterRatShouldNotLDHO NoAct




1~10 1
1~10 1
1~10 3
1~10 1
1~10 1
1~10 3
1~10 1

AMRRateRed, CSInterRatShouldNotLDHO,
PSInterRatShouldNotLDHO InterFreqLDHO
PSInterRatShouldNotLDHO BERateRed

PSInterRatShouldNotLDHO NoAct




1~10 1
1~10 1
1~10 3
1~10 1
1~10 1
1~10 3
1~10 1
0~1, step:0.01 20
0~1, step:0.01 20
0~400000 200000
0~400000 200000
1~15 1
FALSE, TRUE 0
1~3 1
0~1, step:0.01 13
FALSE, TRUE 0
OFF, ON OFF
R99_CONVERSATIONAL, R99_STREAMING, R99_BE,

HSDPA_CONVERSATIONAL, HSDPA_STREAMING,
HSDPA_BE, HSPA_CONVERSATIONAL,
HSPA_STREAMING, HSPA_BE None
8SF4, 7SF4, 6SF4, 5SF4, 4SF4, 3SF4, 2SF4, SF4, SF8,

SF16, SF32, SF64, SF128, SF256 SF8
BLINDHO, MEASUREHO BLINDHO
0~65535 None
INTELLIGENT_INTERFREQ_UE_TYPE_STEERING None
0~65535 None
CSAMR_INTERFREQ, CSNONAMR_INTERFREQ,
PSR99_INTERFREQ, PSHSPA_INTERFREQ None
0~100 80
0~100 80
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
PERIODICAL_REPORTING, EVENT_TRIGGER EVENT_TRIGGER
CPICH_EC/NO, CPICH_RSCP, BOTH CPICH_EC/NO

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D500
0~64000 0
0~14.5, step:0.5 0
0~14.5, step:0.5 6
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
-24~0 -16
-115~-25 -92
0~3 1
0~512 3
0~65535 None
CSAMR_INTERRAT None
0~100 80
0~100 80
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
PERIODICAL_REPORTING, EVENT_TRIGGER EVENT_TRIGGER

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D1000
0~64000, 65535 0
0~64000 0
0~7.5, step:0.5 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640

0~3 1
ALL_USER, HALF, THIRD, QUARTER ALL_USER
0~512 3
0~300 30
0~65535 None
STREAMING, BACKGROUND None
16, 32, 64, 128, 256 None
-35~15, step: 0.1 10
0~1, step: 0.01 80
0~1, step: 0.01 50
0~1279 35
0~2559 10
0~65535 None
PTM, PTP, ENHANCEDPTM, DYNAMIC PTM

2~10 4
1~5 3
0~65535 None
0~3 None
0~65535 None
0~65535 None
16, 32, 64, 128, 256 None
TRUE, FALSE 0
0~65535 None
0~255 None
-10~5 -7
FALSE, TRUE 0
1~255 None
1~32 None
OFF, ON ON
0~65535 None
OFF, ON ON
1~255 10
250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000,
20000, 24000, 28000, 32000, 64000 D3000
-115~-25 -92
-24~0 -12
1~65535 10
0~65535 None
1~255 6
250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000,
20000, 24000, 28000, 32000, 64000 D3000
-115~-25 -92
-24~0 -12
0~65535 None
REQUIRE, NOT_REQUIRE REQUIRE
NOT_REQUIRE, INTER_FREQ, INTER_RAT,

INTER_FREQ_AND_INTER_RAT INTER_FREQ_AND_INTER_RAT
REQUIRE, NOT_REQUIRE, INTER_FREQ, INTER_RAT,
INTER_FREQ_AND_INTER_RAT None
0~4095 None
0~65535 None
0~65535 None
0~255 None
0~65535 None
0~65535 None
0~7 None
0~62, step:2 2
0~62, step:2 2
D6, D15, D25, D50, D75, D100 D6
-140~ -44, step:2 -70
FALSE, TRUE 1
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13,
D14, D15, D16 D0
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
1~504 None
0~65535 None
0~100 3
0~100 3
1~10 3
1~10 3
0.01~0.99, step:0.01 68
1~2, step:0.01 130
1~65535 3000
1~65535 5000
0~10 0
0~10 0
MBMS_REL, USER_REL MBMS_REL
0~8 1
0~10 1
0~3, step:0.1 0
0~65535 None
0~1, step:0.01 45
0~1, step:0.01 70
0~1, step:0.01 5
-20~20, step:2 -2
-20~20, step:2 2
-20~20 -4
-20~20 -4
-20~20 4
-20~20 4
0~65535 None
-15~15 5
0~512 20
0~512 20
CPICH_EC/NO, CPICH_RSCP CPICH_RSCP

0~65535 None
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D2560
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D19
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D1
10~60000, step: 10 64
TEN_MSEC, MIN TEN_MSEC
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
0~65535 None
AMR, VP, PSR99, PSHSPA None
ONLY_TO_INTER_RAT None
0~100 None
0~100 None
BAND1, BAND2, BAND3, BAND4, BAND5, BAND6, BAND7,

BAND8, BAND9, DependOnNCell, BANDINDNOTUSED None
FALSE, TRUE None
0~16383 None
0~16383 None
0~65535 None
0~65535 None
0~65535 None
CS_DOMAIN, PS_DOMAIN None
0~16000000 None
-35~15, step:0.1 None
-35~15, step:0.1 None
SF4, SF8, SF16, SF32, SF64, SF128, SF256, SF512 None
0~65535 None
CPICH_ECNO, CPICH_RSCP CPICH_ECNO
0~40, step:2 2
0~40, step:2 2
{0~40}, {255}, step:2 1
{0~40}, {255}, step:2 1
0~31 1
-24~0 -18
-115~-25, step:2 -58
TRUE, FALSE 0
-4~-2, step:2 None
-50~33 24
{-32~20}, {127}, step:2 5
{-32~20}, {127}, step:2 4
{-32~20}, {127}, step:2 5
{-32~20}, {127}, step:2 4

{-32~20}, {127}, step:2 2
{0~1}, {255}, step:0.1 255
{1~4.75}, {255}, step:0.25 255
{1~4.75}, {255}, step:0.25 255
CONFIGURED, NOT_CONFIGURED NOT_CONFIGURED
NotUsed, 30, 60, 120, 180, 240 NotUsed
1~16 8
NotUsed, 10, 20, 30, 40, 50, 60, 70 NotUsed
{0~40}, {255} 255
{0~40}, {255} 255
{0~40}, {255} 255
{0~40}, {255} 255
{0~31}, {255} 255
{0~6.2}, {255}, step:0.2 255
0~7 4
{0~62}, step:2 2
{0~7} 2
{0~62}, step:2 1
0~65535 None
SIB2, SIB4, SIB12, SIB18, SIB19, SIB11BIS None
0~65535 None
MeasurementQuantity, Both MeasurementQuantity
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~512 30
RSRP, RSRQ RSRP

0~7.5, step: 0.5 4
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
-110~-14(Actual value meets the condition: Actual Value = GUI

Value - 111) 36

Value - 111) 20
0~65535 None
0~1, step:0.01 95
0~1, step:0.01 85
0~10, step:0.1 2
0~65535 None
0~65535 None
0~3 None
20000~65535000, Step:1000 1024
1~10 3
1~1440 60
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~65535 None
-10~5 -7
-22~5 -6
For each switch of this parameter, the value
can be: ON or OFF. None
For each switch of this parameter, the value
can be: ON or OFF. None
For each switch of this parameter, the value can be: ON or

OFF. None

OFF. None
ByRack, ByNodeBId, ByCellId None
0~11 None
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~7 None
0~65535 None
0~65535 None
OFF, ON None
OFF, ON OFF
1~31 10
0~255 80
8, 16, 32, 64, 128, 256 D64
8, 16, 32, 64, 128, 256 D64
HIGH_SPEED_AND_HIGH_COVERAGE_CELL, WALKING_SPEED_AND_HOT_S
OTHER_CELL POT_CELL
FALSE, TRUE 0
8, 16, 32, 64, 128, 256 D8

FALSE, TRUE 1
Limited, Permit, BasedOnUECap BasedOnUECap
FALSE, TRUE 0
0~1530 step:6 10
NOT_ALLOWED, ALLOWED ALLOWED
MODE1, MODE2 MODE2
6~9 6
0~3 None
0~4095 None
0~186 None
R99, R4, R5, R6, R7, R8 None
CR529_SUPPORT, CR529_NOT_SUPPORT None
NORMAL, OFFLOAD, INHIBITED None
0~65535000 step:1000 None

ATM_TRANS, IP_TRANS None
OFF, ON None
1~5 None
OFF, ON None
Each bit can be set ON or OFF None
0~4294967295 0
OFF, ON OFF
0~4294967295 None
0~3 None
PsBlk, CsAndPsBlk None

2~30 None
PRIM, SEC, OUTER, COMM None
3 digits None
2~3 digits None
0~3, 5~31 None
0~3 None
0~3, 5~31 None
0~31 None
1, 2, 3, 4 None
0~3, 5~31 None
0~3, 5~31 None

0~3, 5~31 None
0~3, 5~31 None
5~31, 255 255
ON, OFF None
1024~4294967295 None
0~65535 180
0~180 5
0~999 2
1~65535 5
0~100 10
100, 200, 400, 600, 800, 1000, 1200, 1400, 1600, 1800, 2000,
3000, 4000, 6000, 8000 D2000
0~7 3
100, 200, 400, 1000, 2000 D2000
0~7 3
INFINITY, 5, 10, 30, 60, 120, 360, 720 D30
5, 10, 15, 20, 30, 40, 50 D30
40, 80, 160, 320 D40
1~8 1
1~8 5
1~15 6
1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000 D1
0~15 3
1, 2, 4, 10, 20, 50, 100, 200 D50

0, 2, 4, 6, 8, 12, 16, 20 D0
0, 10, 30, 60, 180, 600, 1200, 1800 D0
1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000 D1
0, 10, 20, 30, 40, 50, INFINITY D30
0, 100, 200, 300, 400, 500, 600, 700, 800, 900, 1000, 1200,
1500, 2000 D600
1, 2, 3, 4 D1
0, 5, 10, 20, 30, 60, 90, 120, INVALID INVALID
CFG_DL_BLIND_DETECTION_SWITCH,
CFG_HSDPA_64QAM_SWITCH, CFG_HSDPA_DC_SWITCH,
CFG_HSDPA_MIMO_SWITCH,
CFG_HSDPA_MIMO_WITH_64QAM_SWITCH,
CFG_HSPA_DTX_DRX_SWITCH,
CFG_HSPA_HSSCCH_LESS_OP_SWITCH,
CFG_HSUPA_16QAM_SWITCH,
CFG_IMS_SUPPORT_SWITCH,
CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH,
CFG_LOSSLESS_RELOC_CFG_SWITCH,
CFG_MULTI_RAB_SWITCH,
CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH,
CFG_PDCP_RFC2507_HC_SWITCH,
CFG_PDCP_RFC3095_HC_SWITCH, CFG_PTT_SWITCH,
CFG_RAB_REL_RMV_HSPAPLUS_SWITCH,
CFG_EDPCCH_BOOSTING_SWITCH,
CFG_HSDPA_DCMIMO_SWITCH,
CFG_FREE_USER_SWITCH,
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH None
DRA_AQM_SWITCH,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH,
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH,
DRA_DCCC_SWITCH,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH,
DRA_HSDPA_STATE_TRANS_SWITCH,
DRA_HSUPA_DCCC_SWITCH,
DRA_HSUPA_STATE_TRANS_SWITCH,
DRA_IP_SERVICE_QOS_SWITCH,
DRA_PS_BE_STATE_TRANS_SWITCH,
DRA_PS_NON_BE_STATE_TRANS_SWITCH,
DRA_R99_DL_FLOW_CONTROL_SWITCH,
DRA_THROUGHPUT_DCCC_SWITCH,
DRA_VOICE_SAVE_CE_SWITCH,
DRA_VOICE_TTI_RECFG_SWITCH None
CS_AMRC_SWITCH,
CS_HANDOVER_TO_UTRAN_DEFAULT_CFG_SWITCH,
CS_IUUP_V2_SUPPORT_SWITCH None
PC_CFG_ED_POWER_INTERPOLATION_SWITCH,
PC_DL_INNER_LOOP_PC_ACTIVE_SWITCH,
PC_DOWNLINK_POWER_BALANCE_SWITCH,
PC_EFACH_ECN0_DYN_ADJ_SWITCH,
PC_FP_MULTI_RLS_IND_SWITCH,
PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH,
PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH,
PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITCH,
PC_INNER_LOOP_LMTED_PWR_INC_SWITCH,
PC_OLPC_SWITCH,
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH,
PC_SIG_DCH_OLPC_SWITCH,
PC_UL_SIRERR_HIGH_REL_UE_SWITCH None
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH,
CMP_IUR_SHO_DIVCTRL_SWITCH,
CMP_UU_ADJACENT_FREQ_CM_SWITCH,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH,
CMP_UU_AMR_SID_MUST_CFG_SWITCH,
CMP_UU_FDPCH_COMPAT_SWITCH,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH None
MAP_HSUPA_TTI_2MS_SWITCH,
MAP_INTER_RAT_PS_IN_CHANLE_LIMIT_SWITCH,
MAP_PS_BE_ON_E_FACH_SWITCH,
MAP_PS_STREAM_ON_E_FACH_SWITCH,
MAP_PS_STREAM_ON_HSDPA_SWITCH,
MAP_PS_STREAM_ON_HSUPA_SWITCH,
MAP_SRB_6800_WHEN_RAB_ON_HSDSCH_SWITCH,
MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH None
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH,
PS_BE_IU_QOS_NEG_SWITCH,
PS_RAB_DOWNSIZING_SWITCH,
PS_STREAM_IU_QOS_NEG_SWITCH,
PS_BE_STRICT_IU_QOS_NEG_SWITCH None
DR_RRC_DRD_SWITCH, DR_RAB_SING_DRD_SWITCH,
DR_RAB_COMB_DRD_SWITCH,
DR_INTER_RAT_DRD_SWITCH, None
HO_ALGO_HCS_SPEED_EST_SWITCH,
HO_ALGO_LDR_ALLOW_SHO_SWITCH,
HO_ALGO_MBMS_FLC_SWITCH,
HO_ALGO_OVERLAY_SWITCH,
HO_INTER_FREQ_HARD_HO_SWITCH,
HO_INTER_RAT_CS_OUT_SWITCH,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH,
HO_INTER_RAT_PS_OUT_SWITCH,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH,
HO_INTRA_FREQ_HARD_HO_SWITCH,
HO_INTRA_FREQ_RPRT_1J_SWITCH,
HO_INTRA_FREQ_SOFT_HO_SWITCH,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH,
HO_MC_NCELL_COMBINE_SWITCH,
HO_MC_SIGNAL_IUR_INTRA_SWITCH,
HO_MC_SIGNAL_SWITCH,
HO_MC_SNA_RESTRICTION_SWITCH,
HO_LTE_PS_OUT_SWITCH,
HO_LTE_SERVICE_PS_OUT_SWITCH,
HO_H2G_SRVCC_SWITCH None
SRNSR_DSCR_IUR_RESRCE_SWITCH,
SRNSR_DSCR_LOC_SEPRAT_SWITCH,
SRNSR_DSCR_PROPG_DELAY_SWITCH,
SRNSR_DSCR_SEPRAT_DUR_SWITCH None
CMCF_DL_HLS_SWITCH, CMCF_UL_HLS_SWITCH,
CMCF_UL_PRECFG_TOLERANCE_SWITCH,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH None
RESERVED_SWITCH_0_BIT32 None
0~4294967295 0
0~4294967295 4294967295
0~255 0
0~255 255
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH,
CMP_IUR_CMCF_SWITCH, CMP_STTD_RL_ADD_SWITCH,
CMP_STTD_ASU_SWITCH,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH,
CMP_WBAMR_SUBFLOW_SWITCH,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH,
CMP_MOCN_PLMN_SEL_SWITCH,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH None
PERFENH_AMR_SPEC_BR_SWITCH,
PERFENH_AMR_TMPLT_SWITCH,
PERFENH_SRB_TMPLT_SWITCH,
PERFENH_OLPC_TMPLT_SWITCH,
PERFENH_AMR_SP_TMPLT_SWITCH,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH,
PERFENH_INTERRAT_PENALTY_50_SWITCH,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH,
PERFENH_UU_P2D_CUC_OPT_SWITCH,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH,
PERFENH_RRC_REDIR_PROTECT_SWITCH None
None
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~255 0
0~255 0
0~255 0
0~255 0
40~100 90
0~65535 None
1~32 None
RAN_CTRLPLN_FC None
0.5~2, Step: 0.01 None
0~1, Step: 0.01 None
0~1, step:0.01 50
0.01~0.1, step:0.01 5
0~255 100
0~255 10
0~255 150
0~3 None
{1~65533}, {65535} None
0~65535 None
0~4799 None
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384 D64

0, 8, 16, 32, 64, 128, 144, 256, 384 D64
RATE_UP_AND_DOWN_ON_DCH, RATE_UP_AND_DOWN_ON_DC
RATE_UP_ONLY_ON_DCH H
RATE_UP_AND_DOWN_ON_EDCH, RATE_UP_AND_DOWN_ON_ED
RATE_UP_ONLY_ON_EDCH CH
0~10, step: 0.1 10
0~10, step: 0.1 20
2_Rates, 3_Rates 3_Rates
0, 1 HAND_APPOINT
16, 32, 64, 128, 144, 256, 384 D128
0, 1 HAND_APPOINT
16, 32, 64, 128, 144, 256, 384 D128
1~255 4
1~65535 60
1~65535 30
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384 D64
10~10000, step: 10 100
8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720,
5440, 11480 D11480
0~11480, step:10kbps 30
0~49 None
MultiIMSI, SingleIMSI None

1~15 characters ***************
1~8 None
0~7 1
0~7 1
0~7 1
OFF, ON OFF
0~765, step: 3 255
0~100 50
0~100 0
1~255 20
1~65535 150
1~65535 150
1~65535 200
1~65535 200
OFF, ON ON
0.1~100, Step:0.1 200
OFF, ON ON
OFF, ON ON
OFF, ON OFF
0~100 20
0~100 1
OFF, ON ON
0~10000, Step:10 6
0~100 5
0~100 1
0~100 5
TPE_DOWNLINK_SWITCH:OFF,
TPE_DOWNLINK_SWITCH, TPE_UPLINK_SWITCH TPE_UPLINK_SWITCH:OFF
1~255 2
10%~1000%, Step:10% 10
0~100% 0
1~10 6
OFF, ON OFF
OFF, ON ON
Qos, Spi, QosAndSpi, BothOFF Qos

0~65535 0
0~65535 0
10%~1000%, Step:10% 100
10%~1000%, Step:10% 10
10%~1000%, Step:10% 1
0~36000, Step:10 6
0~36000, Step:10 0
{1~200} 60
{0~200} 30
{0~200} 10
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
0~100 50
RsvdSwitch1_Bit1:OFF,
RsvdSwitch1_Bit1, RsvdSwitch1_Bit2, RsvdSwitch1_Bit3, RsvdSwitch1_Bit22:OFF,
RsvdSwitch1_Bit31, RsvdSwitch1_Bit32 RsvdSwitch1_Bit32:OFF
RsvdSwitch2_Bit31, RsvdSwitch2_Bit32 RsvdSwitch2_Bit32:OFF
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~5 2
ON, OFF OFF
ON, OFF OFF
ON, OFF OFF
Power, UserNumber UserNumber
OFF, Only_To_Inter_Frequency, Allowed_To_Inter_RAT Only_To_Inter_Frequency
0~100 10
0~100 10
0~100 35
0~100 100
0~100 30
ON, OFF OFF
0~100 7

0~100 13

Band9, DependOnNCell, BandIndNotUsed DependOnNCell
TRUE, FALSE None
0~16383 None
0~16383 None
ON, OFF OFF
0~100 10
0~100 25
OFF, ON OFF
ON, OFF OFF
ON, OFF None
ON, OFF None
0~30 None
0~30 None
0~30 None
0~30 None
0~30 None
0~30 None
0~30 None
0~30 None
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 None
10~60000, step: 10 None
TEN_MSEC, MIN None
10~60000, step: 10 None
1~60 None
10~60000, step: 10 None
TEN_MSEC, MIN None
10~60000, step: 10 None
1~60 None
OFF, ON ON
FALSE, TRUE 1
FALSE, TRUE TURE
1~16 2
0.01~360, step: 0.01 100
6~3600 10
0~255 60
0~255 20
0~255 10
0~100 5
0~255 5

BACKGROUND, NBAMR, WBAMR None
EDCH_10MS, EDCH_2MS None
ON, OFF ON
1, 4, 8, 16, 32, 64, 128, 256 None
2, 4, 15 D2
1, 2, 4, 8, 16, 32, 64, 128, 256, 512, INFINITY None
0, 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, INFINITY None
1, 2, 5 D1
1, 2, 5 D1
ON, OFF ON
4, 5, 8, 10, 16, 20 D5
0, 1, 2, 4, 8, 16, 32, 64, 128, 256, 512 D4
0, 1, 2, 4, 8, 16, 32, 64, 128, 256 D4
TRUE, FALSE 1
0, 2, 4, 8, 10, 20, 40, 80, 160, 16, 32, 64 D2
1, 4, 5, 8, 10, 16, 20 D5
4, 5, 8, 10, 16, 20, 32, 40, 64, 80, 128, 160 D20
1, 4, 5, 8, 10, 16, 20 D5
Low, Middle, High Middle







8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720,
5440, 11480 None
OFF, ON OFF
Gold, Silver, Copper Copper
0~100, step: 0.1 160
0~82 10
0~82 10
0~100, step: 0.1 160
0~82 10
0~82 10
0~100, step: 0.1 160
0~82 10
0~82 10
0~82 3
0~82 3
0~82 4
0~82 4
0~100 12
0~100 28
0~100 56
0~100 83
RTWP, Iub, CE RTWP
0~65535 None
0~65535 None
0~15 8
0~15 15
0~15 15
0.9, 0.8, 0.7, 0.6, 0.5, 0.4, 0.3, 0.2 None
0~65535 None
TTI_2MS TTI_10MS None

SIGNATURE14, SIGNATURE15. (Multiple options.) None

SUBCHANEL9, SUBCHANEL10, SUBCHANEL11. (Multiple
options.) None
-35~-10 -20
1~64 20
1~8 2
1~32 8
0~50 0
0~50 0
0~32 8
8 16 32 64 128 144 256 384 608 1280 2048 2720 5440 D128
8 16 32 64 128 144 256 384 608 1280 2048 2720 5440 D32
0~5000 374
0~65535 None
0~32 None
OFF, ON None
000~999 None
00~99, 000~999 None
0~31 None
1~65533, 65535 None
0~255 None
0~65535 None
0~7 None
0~7 None
0~1023 None
GSM900_DCS1800_BAND_USE
GSM900_DCS1800_BAND_USED, PCS1900_BAND_USED D
NO_CAPABILITY, GSM, GPRS, EDGE None
0~7 0
When CPICH Ec/No (FDD) is employed, unit for Qhcs is dB,
physical value for each parameter value is:
0: -24
1: -23.5
2: -23
3: -22.5
...
45: -1.5
46: -1
47: -0.5
48: 0
49: (spare)
...
98: (spare)
99: (spare)
When CPICH RSCP (FDD) is employed, unit for Qhcs is dBm,

0: -115
1: -114
2: -113
:
88: -27
89: -26
90: -(spare)
91: -(spare)
:
98: -(spare)
99: -(spare) 20
NC0, NC1, NC2, RESET NC0
FALSE, TRUE 0
FALSE, TRUE 0
-50~50 0
0~4095 None
0~65535 None
SINGLE_HOST, DOUBLE_HOST,
DOUBLE_HOST_OUT_POOL SINGLE_HOST
0~31 None
0~511 None

TRUE, FALSE None
0~16383 None
0~16383 None
0~4095 None
0~65535 None
TRUE, FALSE None
1~65533, 65535 None
0~255 None
TRUE, FALSE 0
-24~0 None
TRUE, FALSE 0
-58~-13 None
TRUE, FALSE 0
-4~-2, Step:2 None
TRUE, FALSE 0
-50~33 None
0~7 0
When CPICH Ec/No (FDD) is employed, unit for Qhcs is dB,
0: -24
1: -23.5
2: -23
3: -22.5
...
45: -1.5
46: -1
47: -0.5
48: 0
49: (spare)
...
98: (spare)
99: (spare)
When CPICH RSCP (FDD) is employed, unit for Qhcs is dBm,

0: -115
1: -114
2: -113
:
88: -27
89: -26
90: -(spare)
91: -(spare)
:
98: -(spare)
99: -(spare) 20
TRUE, FALSE 0
STTD_Supported, STTD_not_Supported STTD_not_Supported
CP1_Supported, CP1_not_Supported CP1_not_Supported
OFFSET1, OFFSET2 OFFSET1
None, STTD None
None, STTD None
None, STTD None

DELAY_ACTIVATION_SUPPORT, HSDSCH_SUPPORT,
FDPCH_SUPPORT, EDCH_SUPPORT,
EDCH_2MS_TTI_SUPPORT,
EDCH_2SF2_AND_2SF4_SUPPORT,
EDCH_2SF2_SUPPORT, EDCH_2SF4_SUPPORT,
EDCH_SF4_SUPPORT, EDCH_SF8_SUPPORT,
EDCH_HARQ_IR_COMBIN_SUPPORT,
EDCH_HARQ_CHASE_COMBIN_SUPPORT,
CPC_DTX_DRX_SUPPORT,
CPC_HS_SCCH_LESS_OPER_SUPPORT,
HSPAPLUS_MIMO_SUPPORT,
FLEX_MACD_PDU_SIZE_SUPPORT,
FDPCH_SLOT_FORMAT_SUPPORT,
HSPAPLUS_DL_64QAM_SUPPORT None
FORBIDDEN, NOT_FORBIDDEN NOT_FORBIDDEN
Mode0, Mode1 Mode0
-10~10, step:0.5 0
TRUE, FALSE None
TRUE, FALSE 0
TRUE, FALSE 0
0~65535 None
0~255 None
1~32 None
1~256 230
0~1279 35
0~2559 10
-35~15, step: 0.1 10
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 D15
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 D14
FALSE, TRUE 1
NO_CODING, CONVOLUTIONAL, TURBO CONVOLUTIONAL
1/2, 1/3 D1/2

BACKGROUND None
GOLD, SILVER, COPPER None
1~1000 None
0~65535 None
1~32 None
0~4992 None
1, 2, 3 None
0~512 None
0~512 1
0~512 2
0~65535 None
1~32 None
0~6, step: 0.25 12
-35~15, step:0.1 -30
-35~15, step:0.1 -200
-35~-10 -22
ALGORITHM1, ALGORITHM2 ALGORITHM1
1~2 1
0.5, 1, 1.5, 2 STEPSIZE_1DB
SINGLE_TPC, TPC_TRIPLET_IN_SOFT,
TPC_AUTO_ADJUST SINGLE_TPC
OFF, ON ON
0.4~1, step: 0.04 11
3~9 6
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384 D384
8, 16, 32, 64, 128, 144, 256, 384 D384
8, 16, 32, 64, 128, 144, 256, 384 D16
8, 16, 32, 64, 128, 144, 256, 384 D64
SCHEDULED, NON-SCHEDULED NON-SCHEDULED
10, 20, 50, 100, 200, 500, 1000 D50

2, 10, 20, 50, 100, 200, 500, 1000 D50
10, 20, 50, 100, 200, 500, 1000 D100
2, 10, 20, 50, 100, 200, 500, 1000 D100
8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720, 5440 D256
8, 16, 32, 64, 128, 144, 256, 384 D128
OFF, ON OFF
32, 64 D32
EDCH_TTI_10ms, EDCH_TTI_2ms EDCH_TTI_10ms
8, 16, 32, 64, 128, 144, 256, 384, 608 D384
8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720 None
-24.5~0, step:0.5 41
0~65535 5000
4~1504 502
4~402 302
4~402 42
4~1504 42
MIMO, 64QAM MIMO
0, 1, 2, 4, 8, 16, 32, 64, 128 D32

SRB_OVER_HSDPA, SRB_OVER_HSUPA, TTI_2MS, MIMO,
64QAM, DL_L2_ENHANCE, DTX_DRX,
HSSCCH_LESS_OPERATION, MIMO_64QAM, DC_HSDPA,
UL_L2_ENHANCE, UL_16QAM, EDPCCH_BOOSTING,
DCMIMO_HSDPA None
SLOT_FORMAT_1, SLOT_FORMAT_4 SLOT_FORMAT_1
-100~100 5
-100~100 5
SCHEDULED, NON-SCHEDULED SCHEDULED
SCHEDULED, NON-SCHEDULED SCHEDULED
MIMO_64QAM, DC_HSDPA DC_HSDPA
0~11480 3640
1~15 1
NOT_TRIGGER, TRIGGER NOT_TRIGGER
NOT_PRE_EMPTABLE, PRE_EMPTABLE NOT_PRE_EMPTABLE
NOT_ALLOWED, ALLOWED NOT_ALLOWED
3~9 5
1~100 100
0~1504 60
4~402 302
4~402 42
SCHEDULED, NON-SCHEDULED NON-SCHEDULED

1~100 80
1~100 4
DCH, HSPA DCH
DCH, HSDPA, HSPA DCH
DCH, HSDPA, HSPA HSPA
DCH, HSDPA, HSPA DCH
DCH, HSDPA, HSUPA, HSPA DCH
TRUE, FALSE 0
8, 16 D8
8, 16 D8
8, 16, 32, 64, 128, 144, 256, 384 D64
8, 16, 32, 64, 128, 144, 256, 384, 512, 768, 1024, 1536, 1800,
2048, 3600, 7200, 8640, 10100, 13900 D64
8, 16, 32, 64, 128, 144, 256, 384 D256
8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720, 5440 D608
0~11 None
0~5, 8~27 None
0~11(FG2c), 0~3(GOUc) None

NO, YES None
2~4094 None
20000~60000 20000
3~6 3
OFF, ON ON
OFF, ON ON
OFF, ON ON
RsvdBit1:OFF, RsvdBit2:OFF,
RsvdBit1, RsvdBit2, RsvdBit3, RsvdBit4, RsvdBit5, RsvdBit6, RsvdBit19:OFF, RsvdBit20:OFF,
RsvdBit7, RsvdBit8, RsvdBit9, RsvdBit10, RsvdBit11, RsvdBit21:OFF, RsvdBit22:OFF,
RsvdBit32 RsvdBit31:OFF, RsvdBit32:OFF
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~511 180
1~16 15
0~255 60
0~511 240
1~16 3
0~120 10
MAY, MUST, MUST_NOT MAY
0~1024 0
COEXIST_MEAS_THD_CHOICE_INTERFREQ, COEXIST_MEAS_THD_CHOICE_
COEXIST_MEAS_THD_CHOICE_INTERRAT INTERFREQ
1~4 3
0~120 30
5/15, 6/15, 8/15, 9/15, 12/15, 15/15, 19/15, 24/15, 30/15 PO_24/15
5/15, 6/15, 8/15, 9/15, 12/15, 15/15, 19/15, 24/15, 30/15 PO_24/15
1~4 1
1~4 1
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 2, 4, 8, 10, 20, 40, 80, 160 D8
0, 2, 4, 8, 10, 20, 40, 80, 160 D2
0, 4, 8, 10, 20, 40, 80, 160 D4

BACKGROUND, NBAMR, WBAMR None
NOTUSED, USED None
BIT_ALIGN, OCTET_ALIGN None
0, 1, 2, 3, 4 None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,
52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83,
84, 85, 86, 87, 88, 89, 90 None
FALSE, TRUE None

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,
52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83,
84, 85, 86, 87, 88, 89, 90 None
FALSE, TRUE None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,
52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83,
84, 85, 86, 87, 88, 89, 90 None
FALSE, TRUE None

1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19,
20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31, 32, 33, 34, 35,
36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51,
52, 53, 54, 55, 56, 57, 58, 59, 60, 61, 62, 63, 64, 65, 66, 67,
68, 69, 70, 71, 72, 73, 74, 75, 76, 77, 78, 79, 80, 81, 82, 83,
84, 85, 86, 87, 88, 89, 90 None
FALSE, TRUE None
100, 200, 400, 600, 800, 1000, 1200, 1400, 1600, 1800, 2000,
3000, 4000, 6000, 8000 D2000
0~7 3
1~15 6
1, 2, 4, 10, 20, 50, 100, 200, 400, 600, 800, 1000 D1
0~65535 None
0~50, step: 0.1 430
-35~15, step: 0.1 -50
-35~15, step: 0.1 -50
-10~50, step: 0.1 330

-10~50, step: 0.1 346
-10~50, step: 0.1 313
-35~15, step: 0.1 -20
-10~5 -7
-35~15, step: 0.1 -130
0~255 None
0~31 None
Band_a, Band_b, Band_c, Band_d, BandIndNotUsed None
0~16383 None

CHIP1536, CHIP1792, CHIP2048, CHIP2304 None
PScramCode0, PScramCode1, PScramCode2, PScramCode3,

PScramCode4, PScramCode5, PScramCode6, PScramCode7 None
0~11 None
0~27 None

10, 20, 40, 80, 160, 320, 640, 1280 D1280
0~255 None
0~3 None
0~65535 None
0~255 None
64, 128, 192, 256, 320, 384, 512 None
-35~15, step:0.1 None
-11~4 None
0~255 None
0~255 None
0~255 None
18~32 None
1, 2, 3, 4 None
0~3 None
0~16777215 None
64, 128, 192, 256, 320, 384, 512 None
0~3 None
0~16777215 None
64, 128, 192, 256, 320, 384, 512 None
0~3 None
0~16777215 None
64, 128, 192, 256, 320, 384, 512 None
0~3 None
0~16777215 None
64, 128, 192, 256, 320, 384, 512 None
0, 1, 2, 3, 4 None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 None

QPSK, 16QAM QPSK
2, 3, 4, 5 None
OFF, ON OFF
Fast_Dormancy, HSDPA_RB_Setup_Cmp_CRC None
0~99999999 None
1~64 length of byte None
ON, OFF OFF
This parameter is set to 0 or 1 according to the related

domains. None
0~999 None
0~999 None
0~3 None
0~4095 None
15-bit decimal numerals None
15-bit decimal numerals None
3 digits None
2~3 digits None
TRUE, FALSE None
0~65535 None
000~999 None
00~99, 000~999 None

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D500
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~14.5, step:0.5 0
0~2, step:0.1 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0~64000 0
-24~0 -14
-24~0 -12
-24~0 -14
-24~0 -14
-24~0 -12
-24~0 -12
-115~-25 -95
-115~-25 -92
-115~-25 -95
-115~-25 -95
-115~-25 -92
-115~-25 -92
-24~0 -12
-24~0 -12
-24~0 -12
-115~-25 -92
-115~-25 -92
-115~-25 -92
-24~0 -12
-24~0 -12
-24~0 -12
-115~-25 -92
-115~-25 -92
-115~-25 -92
0~512 60
500~32000, step:500 1
0~1000 0
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~14.5, step:0.5 6
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
-24~0 -16
0~512 60
500~32000, step:500 4
0~4095 None
0~65535 None
0~4095 None
0~65535 None
-10~10, step:0.5 0
FALSE, TRUE 1
-50~50 0
-50~50 0
FALSE, TRUE 0
-50~50 0
-50~50 0
0, 10, 20, 30, 40, 50, 60 D0
3, 6, 9, 12, 15, 18, 21, INFINITY D3
2, 3, 4, 6, 8, 10, 12, INFINITY D2
0~3 2
FALSE, TRUE 0
-115~-25 -92
FALSE, TRUE 0
0~63 None
-24~0 -18
FALSE, TRUE 0
0~15 0
FALSE, TRUE 0
FALSE, TRUE 0
-24~0 -24
-115~-25 -58
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
CPICH_EC/NO, CPICH_RSCP, AUTO AUTO

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~2, step:0.1 0

4000, 6000, 8000, 12000, 16000, 20000, 24000, 28000,
32000, 64000 D1000
0~14.5, step:0.5 4
0~14.5, step:0.5 4
0~7.5, step:0.5 4
0~7.5, step:0.5 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
0~64000, 65535 0
0~64000 0
-24~0 -14
-24~0 -12
-24~0 -15
-24~0 -15
-24~0 -13
-24~0 -13
-115~-25 -100
-115~-25 -97
-115~-25 -110
-115~-25 -110
-115~-25 -107
-115~-25 -107


-24~0 -12
-24~0 -13
-24~0 -13
-115~-25 -97
-115~-25 -107
-115~-25 -107
0~512 60
0~65535 0
0~7.5, step:0.5 0
500~32000, step:500 1
0~63 3
0~65535 30
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~7.5, step:0.5 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640

1~16 16
0~512 60
OFF, ON OFF
OFF, ON ON
0~100 80
0~100 60
500~32000, step:500 4
0~63 3
0~65535 30
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
CPICH_EC/NO, CPICH_RSCP CPICH_EC/NO
1, 2, 4, 8, 16, 32, 64, INFINITY D16

8000, 16000 D4000
1, 2, 4, 8, 16, 32, 64, INFINITY D16

8000, 16000 D4000
1, 2, 4, 8, 16, 32, 64, INFINITY D64

8000, 16000 D1000
0~14.5, step:0.5 6
0~14.5, step:0.5 6
0~14.5, step:0.5 6
0~14.5, step:0.5 12
0~14.5, step:0.5 12
0~14.5, step:0.5 12
-24~0 -24
-115~-25 -115
0~7.5, step:0.5 0
0~7.5, step:0.5 0
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~7.5, step:0.5 8
0~2, step:0.1 0
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0~120 60
0~63 3
-14.5~14.5, step:0.5 2
0~255 30
-24~0 -24
1~6 3
-115~-25 -115
250, 500 D250

1, 2, 4, 8 D2
0~4095 None
0~65535 None
0~4095 None
0~65535 None
-10~10, step:0.5 0
AFFECT, NOT_AFFECT AFFECT
AFFECT, NOT_AFFECT AFFECT
FALSE, TRUE 1
-50~50 0
-50~50 0
FALSE, TRUE 0
-50~50 0
-50~50 0
0, 10, 20, 30, 40, 50, 60 D0
3, 6, 9, 12, 15, 18, 21, INFINITY D3
2, 3, 4, 6, 8, 10, 12, INFINITY D2
FALSE, TRUE 0
0~30 None
FALSE, TRUE 1
0~63 None
0~3 None
0~63 None
HTTP, P2P, SPI, UNRECOGNIZED SPI
IP, Port, IPAndPort None
0.0.0.0~255.255.255.254 None
0.0.0.0~255.255.255.255 None
0~65534 None
TCP, UDP, ALL None
HIGH, MIDDLE, LOW MIDDLE
0~11 None
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
1~32 None
TRUE, FALSE None
0~11 None
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~7 None
0~186 None
0~11 None
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~7 None
0~3 None
0~4095 None
0~5 2
10000~240000 30000
0~240000 120000
1000~300000 20000
5000~30000 20000
15000~120000 60000
OFF, ON ON
1, 2, 3, 4, 5, 6, 7, 8, 9, 10 D6
0~100 60
0~65534 200
0~100 60
0~65534 100
0~100 60
0~65534 100
0~100 60
0~65534 100
0~100 60
0~65534 100
0~100 60
0~65534 100
0~100 40
0~65534 200
0~100 40
0~65534 200
0~100 40
0~65534 200
SPU_KPI_AUTOCURE_SWITCH None
0~100 0
0~3 None
{1~65533}, {65535} None
1~256 None
1~256 None
{1~65533}, {65535} None
0~65535 None
000~999 None
00~99, 000~999 None
1~65533, 65535 None
IUBLDR, CODELDR, UULDR, CREDITLDR IUBLDR
IUBLDR, CODELDR, UULDR, CREDITLDR CREDITLDR
IUBLDR, CODELDR, UULDR, CREDITLDR CODELDR
IUBLDR, CODELDR, UULDR, CREDITLDR UULDR
NODEB_CREDIT_LDR_SWITCH,
LCG_CREDIT_LDR_SWITCH, LC_CREDIT_LDR_SWITCH None
OFF, ON ON
1~115300 1800
6~115300 1800
1~86400 10
100~86400000 3000
1~255 11
1~115300 1800
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D6
10~60000, step:10 100
1~60 20
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D6

10~60000, step:10 100
1~60 20
2~65535 150
1~32 6
1~32 6
1~32 5
1~32 5
1~32 5
1~32 5
1~32 5
1~32 5
10~60000, step:10 100
1~60 10
1~32 5
10~60000, step:10 100
1~60 10
1~32 5
2~255 3
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D3
10~60000, step:10 20
1~60 20
10~60000, step:10 100
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D3
10~60000, step:10 20
1~60 20
10~60000, step:10 100
10~60000, step:10 100
1~60 1
1~32 5
1~32 32
0~268435455 None
0~65535 None
0~268435455 None
Numeric string of three digits in the range of zero to nine None
Numeric string of two or three digits in the range of zero to nine None
0~65535 None
0~31 None
0~503 None
1~14 None
0~5379 None
NotSupport, Support NotSupport
False, True 0
0~4095 None
0~65535 None
0~65535 None
1~10 2
000~999 None
000~999 None
0~16777215 None
16, 32, 64, 128, 256 None
-35~15, step:0.1 None
0~1, step: 0.01 80
0~1, step: 0.01 50
0~1279 35
0~2559 10
CH0, CH1, CH2, CH3, CH4 None
OFF, ON None
000~999 None
00~99, 000~999 None
0~4294967295 None
0~3 None
0~65535 None
16, 32, 64, 128, 256 None
TRUE, FALSE 0
OFF, ON None
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, SERVICE-BASED, LOAD-BASED, DYNAMIC-BASED OFF
-100~100 10
-100~100 30
1~20 3
OFF, ON OFF
OFF, ON OFF
0~10 10
OFF, ON OFF
0~100 0
0~100 50
RRC, RAB, RRC_RAB RRC_RAB
7~10 7
0~3 3
0~3 1
OFF, ON ON
1~255 10
250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000,
20000, 24000, 28000, 32000, 64000 D3000
-115~-25 -92
-24~0 -12
1~65535 10
1~255 6
250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000,
20000, 24000, 28000, 32000, 64000 D3000
-115~-25 -92
-24~0 -12
OFF, ON OFF
15-bit numerical (0 to 9) string None
-35~15, step:0.1 -30

16, 32, 64, 128, 256 None
TRUE, FALSE 0
FTP, MSN, ICMP, RTSP, SMTP None
OFF, ON None
0~4294967295 None
0~11 None
0~5, 8~27 None
0~11(FG2c), 0~3(GOUc) None
0~3 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~65535 None
0~65535 None
OFF, ON None
RELIABILITY_CELL_SELFCURE_SWITCH
CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH None
PERFENH_R99_BRDCSTHSPA_SWITCH None
None
0~4294967295 0
0~4294967295 0
0~255 0
0~255 0

00:00:00~23:59:59 None
5~1440, step:5 None
1~32 None
0~11 None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
SAAL, SCTP, SAAL-SCTP None
0~1399 None
0~1199 None
SAAL, SCTP SAAL
ATMTODUAL, IPTODUAL, DUALTOATM, DUALTOIP None

SAAL, SCTP None
0~11 None
0~5, 8~27 None
0~31(AEUa), 0~125(E1 of AOUa), 0~167(T1 of AOUa),

0~251(E1 of AOUc), 0~335(T1 of AOUc) None
OFF, ON ON
0~1999 1
0~199 0
OFF, ON OFF
0~199 None
0~65535 None
0~11 None
{0}, {2}, {4}, {8}, {10}, {12}, {14}, {16}, {18}, {20}, {22}, {24}, {26} None
0~7 None
ATM_TRANS, IP_TRANS, ATMANDIP_TRANS,

HYBRID_IP_TRANS ATM circuit transmission
SUPPORT, NOT_SUPPORT None
0~65535 10
TRUE, FALSE 0
R99, R4, R5, R6, R7, R8, R9 R9
SHARE, EXCLUSIVE SHARE
OFF, ON ON
SINGLEHOST, PRIMHOST, SECHOST SingleHost
0~4095 None
0~65535 None
Dedicated, RANSharing, MOCN None
0~3 None
TRUE , FALSE 0
IUB_LDR, NODEB_CREDIT_LDR, LCG_CREDIT_LDR,

IUB_OLC None
0~3840 3840
0~3840 3840
MBR, GBR MBR

0~4294967295 0
0~4294967295 0
0~65535 None
ETH/TRUNK, PPP/MP None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
OFF, ON OFF
0.0.0.0~255.255.255.255 None
0~65535 None
ATMTRANS_IP, IPTRANS_IP, ATMANDIPTRANS_IP None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None
NO, YES None
0~988 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~11 None
0~5, 8~27 None
2~4094 None
0~7 None
NoAct, BERateRed, QoSRenego, CSInterRatShouldBeLDHO,

PSInterRatShouldBeLDHO, AMRRateRed,





1~10 1
1~10 1
1~10 3
1~10 1
1~10 3
1~10 1






1~10 1
1~10 1
1~10 3
1~10 1
1~10 3
1~10 1
1~10 1
1~10 1
8SF4, 7SF4, 6SF4, 5SF4, 4SF4, 3SF4, 2SF4, SF4, SF8,

SF16, SF32, SF64, SF128, SF256 SF8
0~65535 None
0~10 1
0~10 1
0~4095 None
0~65535 None
IntraFreqNCell, InterFreqNCell, InterRatNCell None
0~3 None
0~4095 None
0~1023 None
0~4095 None
CS_SHO_SWITCH, HSPA_SHO_SWITCH,
NON_HSPA_SHO_SWITCH None
OFF, ON None
SUPPORT_CS, SUPPORT_PS, SUPPORT_CS_AND_PS None
TRUE, FALSE None
0~186 None
R99, R4, R5, R6, R7, R8, R9 None
1~300 20
NO, YES NO
DL_DCCH_SWITCH, IUR_TRG_SWITCH None
ATM_TRANS, IP_TRANS None

CORRM_SRNSR_PSBE_RELOC,
CORRM_SRNSR_PSBE_DSCR CORRM_SRNSR_PSBE_RELOC
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
OFF, ON OFF
This parameter is set to 0 or 1 according to the related RNC_NODE_REDUNDANCY_CO

domains. MPATIBLE_SWITCH:OFF
domains. None
0~4294967295 0
OFF, ON OFF
0~4095 None
0~65535 None
0~3, 5~31 None
0~3 None
OFF, ON OFF
NOT_PERMIT_OFFLOAD, PERMIT_OFFLOAD NOT_PERMIT_OFFLOAD
0~100 80
OFF, ON OFF
domains. None

domains. None
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~3 None

domains. None

domains. None
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~127 None
0~3 None
1 to 100 character(s) None
0~99999999 None
1~64 length of byte None
0~3 None
9~15 numbers None
9~15 numbers None
0~3 None
GOLDEN_USER, SILVER_USER, COPPER_USER None
STREAMING, INTERACTIVE, BACKGROUND None
0~3 None

SUPP_IUFLEX_MOCN SUPP_NONE
SUPP_IUFLEX_MOCN SUPP_NONE
0~60 3
1~10 None
1~10 None
0~1023 None
OFF, ON OFF
OFF, ON OFF
60~900 900
60~900 900
NO, YES NO
NO, YES NO
NO, YES YES

NO, YES YES
0~3, 255 255
COMM_MOCN_NRI_GLOBAL_CONFIG_MODE_SWITCH,
COMM_MIB_MULTI_PLMN_LIST_ALLOWED_SWITCH,
SPARE_5_SWITCH, SPARE_6_SWITCH None
0~3 None
0~256000 128
0~256000 384
0~256000 512
0~256000 1000
0~256000 2000
0~256000 4000
0~256000 8000
0~256000 16000
0~256000 32000
0~64000 128
0~64000 384
0~64000 512
0~64000 768
0~64000 1000
0~64000 1500
0~64000 2500
0~64000 5500
0~64000 7500
0~3 None
INTERACTIVE, BACKGROUND None

High, Medium, Low None
2~11 None
0~3 None
0~15 None
1~100 100
FALSE, TRUE 0
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
0~3 None
High, Medium, Low High
High, Medium, Low Medium

High, Medium, Low Low
0~3 None
INTERACTIVE, BACKGROUND, IMSSIGNALLING, PTT None

R99, HSPA None
0, 8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720,
5440 D64
0, 8, 16, 32, 64, 128, 144, 256, 384, 512, 768, 1024, 1536,
1800, 2048, 3600, 7200, 8640, 10100, 13900, 16000, 21000 D64
0~3 None

0~27900 0
0~3 None
Gold, Silver, Copper Gold
Gold, Silver, Copper Silver

ARP, TrafficClass ARP
NONE, DCH, HSPA NONE
0~65535 None
0~255 3
0~65535 None
0~255 None
1~32 3
1~256 230
0~1279 35
0~2559 10
-35~15, step: 0.1 -20
0~65535 None
1~32 3
0~4992 None
1~2 None
0~1 None
1 1
0~65535 None
0~255 2
-10~50, step: 0.1 330
-10~50, step: 0.1 346
-10~50, step: 0.1 313
-100~500 330
0~65535 None
-10~50, step: 0.1 346
-10~50, step: 0.1 313

OFF None
OFF None
1~255 None
1~255 None
0~65535 None
0~255 None
0~255 10
18, 36, 72, 144 V36
TRUE, FALSE 0
0~65535 None
-10~5 -7
LAC, RAC None
0~3 None
{{1~65533}, {65535}} None
{0~255} None
{1~256} None
{1~256} None
REHOSTRIGHNOW, REHOSTDELAY, REHOSTWHEN REHOSTRIGHNOW
0~3600 0
00:00:00~23:59:59 None
0~65535 None
0~255 None

options.) None
0~65535 None
0~255 4

0~65535 None
0~255 4
ASC0, ASC1, ASC2, ASC3, ASC4, ASC5, ASC6, ASC7 None
0~15 0
0~15 7
0~15 15
0.9, 0.8, 0.7, 0.6, 0.5, 0.4, 0.3, 0.2 None
0~65535 None
0~255 4


options.) None
-35~-10 -20
1~64 20
1~8 2
2, 4, 6, 8, 12, 16, 24 BIT2
0~65535 None
0~255 4
D1, D2, D3, D4 None
0~3 0
0~3 1
0~3 2
0~3 3
0~65535 None
0~255 4
0~16777215 None
-5~10 None
1~15 None
0~15 15
0~65535 None
0~255 None
-35~-10 -20
1~8 2
1~64 20
0~65535 None
0~255 0
-35~15, step: 0.1 -50
0~14400 20
0~60 20
0~14400 20
0~60 20
0~14400 20
0~60 20
0~14400 20
0~60 20
0~64800 360
0~60 20
0~64800 20
0~64800 4
0~64800 10
ON, OFF ON
0~2 2
0~5120 320
0~2 2
OFF, ON ON
OFF, ON ON
1~65535 3
1~65535 3
1~65535 3
1~65535 3
8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D8
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
250, 500, 1000, 2000, 4000, 8000, 16000 D1000

10~100000, step: 10 110
0~384000, step: 10 10
0~1023 1
0~1023 1
1~65535 10
8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D8
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D80
250, 500, 1000, 2000, 4000, 8000, 16000 D250
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D16
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D64
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
OFF, ON OFF
NO, YES YES
NO, YES NO
NO, YES NO
None, RateDegrade, InterFreqHO, InterRatHO None
20~64000 3000
None, RateDegrade, InterFreqHO, InterRatHO RateDegrade
SINGLE, COMBINE SINGLE
NO, YES YES
NO, YES NO
NO, YES NO
20~64000 3000
NO, YES NO
NO, YES NO
NO, YES NO
20~64000 3000
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES NO
NO, YES YES
NO, YES YES
NO, YES NO
0~1024 20
-15~15 5
0~512 20
0~512 20
CPICH_EC/NO, CPICH_RSCP CPICH_RSCP
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D320
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D640
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D2560
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D240
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D19
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D1
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480
1~60 None
10~60000, step: 10 64
10~60000, step: 10 480

1~60 None
OFF, ON OFF
OFF, ON OFF
OFF, ON ON
OFF, ON OFF
5~20 5
10~800, step:10 50
1~60, step:1 5
OFF, ON ON
0~3 None
{1~65533}, {65535} None
0~255 None
1~256 None
1~256 None
0~65535 None
0~255 4
1~32 1
1~256 1
0~50 0
0~50 0
1~32 8
0~65535 None
1~32 1
0~4992 None
1~2 None
0~512 1
0~512 2
0~5, step: 0.001 5000
0~5, step: 0.001 3000
0~5, step: 0.001 500
0.1~100, step: 0.1 10
10~10000, step: 10 100
-24.5~0, step: 0.5 Actual value = (GUI value - 49(offset))*0.5 49
-24.5~0, step: 0.5 Actual value = (GUI value - 49(offset))*0.5 21
AMR, VP, PSR99, PSHSPA None
ONLY_TO_INTER_RAT None
0~100 0
0~100 None
BAND1, BAND2, BAND3, BAND4, BAND5, BAND6, BAND7,

BAND8, BAND9, DependOnNCell, BANDINDNOTUSED DependOnNCell
FALSE, TRUE None

0~16383 None
0~16383 None
0~65535 None
SF4, SF8, SF16, SF32, SF64, SF128, SF256 None
0~255 None
{0~511} None
PsBlk, CsAndPsBlk None

2~30 None
0~4095 None
ATM address None
0~3 None
0~11 None
0, 2, 4, 6, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~7 None
OFF, ON OFF
OFF, ON OFF
GERMAN, ENGLISH, ITALIAN, FRENCH, SPANISH, DUTCH,
SWEDISH, DANISH, PORTUGUESE, FINNISH,
NORWEGIAN, GREEK, TURKISH, HUNGARIAN, POLISH,
LANGUAGEUNSPECIFIED ENGLISH
1~4096 300
0~65535 0
OFF, ON OFF
1~3600 20
60~3600 180
16, 32, 64, 128, 256 D16
0~1, step: 0.01 70
1~5 3
2~10 4
1~5 3
2~20 2
10~3600, step: 10 6
0~60 10
ON, OFF OFF
ON, OFF ON
ON, OFF ON
8, 16, 32, 64, 128, 144, 256 D16
0 None
1~60 1
5 5
2 2
NONE, IUCS, IUPS, IUCS_IUPS IUCS_IUPS
0 None
0~4095 None
3 digits None
2~3 digits None
0~3, 5~31 None
0~31 None
1~100 None
ORIGCONVCALLEST, ORIGSTREAMCALLEST,
ORIGINTERCALLEST, ORIGBKGCALLEST,
ORIGSUBSTRAFFCALLEST, TERMCONVCALLEST,
TERMSTREAMCALLEST, TERMINTERCALLEST,
TERMBKGCALLEST, EMERGCALLEST,
INTERRATCELLRESELEST,
INTERRATCELLCHGORDEREST, REGISTEST,
DETACHEST, ORIGHIGHPRIORSIGEST,
ORIGLOWPRIORSIGEST, CALLREEST,
TERMHIGHPRIORSIGEST, TERMLOWPRIORSIGEST,
TERMCAUSEUNKNOWN, MBMSCALLEST, DEFAULTEST None

DCH_13.6K_SIGNALLING, DCH_27.2K_SIGNALLING None
OFF, ON None
1~15 None
DCH_13.6K_SIGNALLING, DCH_27.2K_SIGNALLING DCH_13.6K_SIGNALLING











DCH_13.6K_SIGNALLING, DCH_27.2K_SIGNALLING FACH






domains. None
This parameter is set to 0 or 1according to the related
domains. None

domains. None
domains. None

domains. None
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 0
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~4294967295 4294967295
0~3 None
{1~65533}, {65535} None
0~65535 None
0~3 None
0~65535 None
2~10 4
1~5 3
0~3 None
0~3 None
0~186 None
OFF, ON ON
0~3 None
0~186 None
1~115300 1800
6~115300 1800
1~86400 10
100~86400000 3000
1~255 11
1~115300 1800
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D6
10~60000, step:10 100
1~60 20
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D6
10~60000, step:10 100
1~60 20
2~65535 150
1~32 6
1~32 6
1~32 5
1~32 5
1~32 5
1~32 5
1~32 5
1~32 5
10~60000, step:10 100
1~60 10
1~32 5
10~60000, step:10 100
1~60 10
1~32 5
2~255 3
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D3
10~60000, step:10 20
1~60 20
10~60000, step:10 100
D0, D1, D2, D3, D4, D5, D6, D7, D8, D9, D11, D13, D15, D17,
D19 D3
10~60000, step:10 20
1~60 20
10~60000, step:10 100
1~32 32
0~65535 None
0~255 None
-35~15, step: 0.1 -20

0~149 50
0~65535 None
0~255 None
0~149 50
0~15 None
TRUE, FALSE 0
2, 4, 6, 8, 12, 16, 24 BIT4
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17 None
EXISTS, NOT_EXISTS None
COMMON, MCCH COMMON
0~65535 None
0~255 None
0~16777215 None
2~11 None
0~65535 None
CELLID_CENTER, CELLID_RTT, OTDOA, A-GPS None

UE_ASSISTED_PREFERRED UE_BASED
NODELIVERY, DELIVERY NODELIVERY
GPS_REALTIME_INTEGRITY None
GPS_REALTIME_INTEGRITY None
4~16 16

UE_ASSISTED_PREFERRED UE_ASSISTED

UE_ASSISTED_PREFERRED UE_ASSISTED
OFF, ON OFF
NO, YES YES
DRD, MEAS_BASED DRD
R5_POSDATA_SWITCH,
LAST_KNOWN_SERVICE_AREA_SWITCH None
OFF, ON OFF
0~14.5, step: 0.5 12
0~14.5, step: 0.5 18
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D160
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D1280
-24~0 -20
RNC_CENTRIC, SAS_CENTRIC,
SAS_CENTRIC_PREFERRED RNC_CENTRIC
250, 500, 1000, 2000, 3000, 4000, 6000, 8000, 12000, 16000,
20000 1000
POINT, POINT_WITH_UNCERTN,
ELPSD_POINT_WITH_UNCERTN_ELLIPSE,
ELPSD_POINT_WITH_ALT,
ELPSD_POINT_WITH_ALT_AND_UNCERTN_ELPSD,
ELPSD_ARC, AUTOMATIC AUTOMATIC
0~4095 None
0~65535 None
CELL_ANTENNA, CELL_CENTER, BOTH None
0, 1 DEG
0, 1 MET
-90~90, step: 0.000001 None
-180~180, step: 0.000001 None
-32767~32767 None
1~100000 None
0~360, step: 0.1 None
0~360, step: 0.1 None

-32767~32767 None
-10000~10000 None
NLOS_ENVIRONMENT, LOS_ENVIRONMENT,
MIXED_ENVIRONMENT MIXED_ENVIRONMENT
-90~90, step: 0.000001 None
-180~180, step: 0.000001 None
-32767~32767 None
0~1800000 None
0~1800000 None
0~179 None
0~990 None
-90~90 None
-180~180 None
-90~90 None
-180~180 None
-107502~107502 None
3~328080 None
-107502~107502 None
-32808~32808 None
-107502~107502 None
0~5905440 None
0~5905440 None
0~3248 None
1~8 None
0~7 1
0~7 1
0~7 1
0~7 1
0~7 1
0~15 None
1~100 100
FALSE, TRUE 0
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
1~100 100
0~5, step: 0.01 313
0~5, step: 0.01 200
1~255 60
0~400 400
1~100 5
1~65535 60
1~255 30
RT, NRT, ALL NRT
0~65535 None
0~255 1
-35~15, step: 0.1 -50
1~10000 5000
1~10000 5000
1~5000 350
1~10000 5000
1~10000 5000
1~3000 1000
300~300000 5000
1~10000 5000
300~300000 5000
300~300000 5000
1~10000 5000
1~10000 5000
1~10000 5000
1~300000 11000
1~10000 5000
1~10000 5000
1~10000 5000
1~10000 5000
1~10000 5000
1~300000 5000
1~300000 5000
1~300000 5000
1~20000 10000
1~60000 45000
1~20000 20000
1~10000 5000
1~20000 15000
1~10000 5000
1~10000 5000
1~20000 10000
1~10000 3000
1~255 10
1~10000 5000
1~10000 5000
1~10000 5000
1~65535 300
1~65535 300
0~15 4


0~111 None
0~6, 11~19, 21~28, 40~69, 70~111 None

BACKGROUND None
SPEECH, UNKNOWN None
0~256000000 None
1~15 None
1~15 None
HO_TO_GSM_SHOULD_BE_PERFORM,
HO_TO_GSM_SHOULD_NOT_BE_PERFORM,
HO_TO_GSM_SHALL_NOT_BE_PERFORM None
GSM, GPRS, EDGE None
NORMAL, SILENT None
APPLIED_ON_UPLINK, APPLIED_ON_DOWNLINK,
APPLIED_ON_BOTH None
HO_TO_EUTRAN_SHOULD_BE_PERFORM, HO_TO_EUTRAN_SHALL_NOT_
HO_TO_EUTRAN_SHALL_NOT_BE_PERFORM BE_PERFORM
0~111 None
UPLINK, DOWNLINK None
16, 32, 64, 128, 256, 512, 1024, 2K, 3K, 4K, 6K, 8K, 12K, 16K,
24K, 32K, 48K, 64K, 96K, 128K, 192K, 256K, 384K, 512K,
768K D1024
8, 16, 32, 64, 128, 256, 512, 1024, 2K, 3K, 4K, 6K, 8K, 12K,
16K, 24K, 32K, 48K, 64K, 96K, 128K, 192K, 256K, 384K, 512K None
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000, 10000, 15000, 20000, 25000, 30000 None
250, 500, 1000, 2000, 4000, 8000, 16000 D4000

0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000, 10000, 15000, 20000, 25000, 30000 D2560
250, 500, 1000, 2000, 4000, 8000, 16000 D4000
0~1023 2
0~1023 16
0~1023 2
0~1023 16
0~1023 2
0~1023 16
0~111 None
TRCH_HSDSCH, TRCH_EDCH_2MS, TRCH_EDCH_10MS None
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 120, 140, 160, 200,
300, 400 D60
4, 6, 8, 12, 16, 24, 32, 64, 128 D16
1, 2, 3, 4, 5, 6, 7, 8 D1
1~5000 336
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
FALSE, TRUE None
20, 40, 60, 80, 100, 120, 140, 160, 180, 200, 250, 300, 400,
500, 750, 1000, 1250, 1500, 1750, 2000, 2500, 3000, 3500,
4000, 4500, 5000, 7500 D100
0.5~25.5, step: 0.001 1010
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12 D1
1~5000 336
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
1~5000 None
2, 10, 20, 50, 100, 200, 500, 1000 D50
1~64 32
10~640, step: 10 None
0~111 None
0~2 None
TRCH_EDCH_2MS, TRCH_EDCH_10MS None
TRUE, FALSE None
TRUE, FALSE None
TRUE, FALSE None
-8.2~17.3, step: 0.1 None
-8.2~17.3, step: 0.1 None
-8.2~17.3, step: 0.1 None
0~3 None
1, 2, 3, 4, 5, 6, 7, 8 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
0~37 None
0~37 None
TRUE, FALSE None
PO_8/15, PO_11/15, PO_15/15, PO_21/15, PO_30/15,

PO_42/15, PO_60/15, PO_84/15 PO_30/15
0~6 0
0~6 0
0~6 0
0~111 None
0~2 None
TRCH_DCH, TRCH_EDCH_2MS, TRCH_EDCH_10MS None
1~5 None
5*10^(-7)~1 None
0~5, step: 0.001 None
0~15 None
0~15, step: 0.001 None
0~15, step: 0.001 None
0~111 None
0~82 None
0~82 None
0~82 None
0~82 None
1~512 None
1~512 None
1~512 None
0~111 None
0~2 None

TRCH_EDCH_10MS None
TRCH_DCH, TRCH_HSDSCH None
1~5 None
AM, UM, TM None
SENDER_PARA, RECEIVE_PARA, FLOWCONTROL_PARA None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 None
50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600,
700, 800, 900, 1000 None
1, 4, 6, 8, 12, 16, 24, 32 D32
FALSE, TRUE 1
NO_DISCARD NO_DISCARD
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING None
50, 60, 70, 80, 90, 100, 120, 140, 160, 180, 200, 300, 400,
500, 700, 900 None
100, 250, 500, 750, 1000, 1250, 1500, 1750, 2000, 2500,
3000, 3500, 4000, 4500, 5000, 7500 None
1, 4, 6, 8, 12, 16, 24, 32 None
10, 20, 30, 40, 50, 60, 70, 80, 90, 100 None
2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40 None

50, 60, 70, 80, 90, 100, 120, 140, 160, 180, 200, 300, 400,
500, 700, 900 None
1, 4, 6, 8, 12, 16, 24, 32 None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40 None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 None
FALSE, TRUE 1
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
100, 200, 300, 400, 500, 750, 1000, 2000 None
FALSE, TRUE None
FALSE, TRUE 1
FALSE, TRUE 1
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
1, 2, 4, 8, 16, 32, 64, 128 None
1, 4, 16, 64 None
50, 60, 70, 80, 85, 90, 95, 99 None
100, 200, 300, 400, 500, 750, 1000, 2000 None
FALSE, TRUE 0
FALSE, TRUE 0
0~500000 5000
40~60000 1000
0~10 1
0~100, step: 0.1 160

1~100 2
0~1000 1
0~100, step: 0.1 80
1~100 14
0~1000 1
0~100, step: 0.1 50
1, 2, 4, 8, 16, 32, 64, 128 None
1, 4, 16, 64, None
1, 2, 4, 8, 16, 32, 64, 128 None
1, 4, 16, 64, None
0~4 None
TRCH_EDCH_2MS, TRCH_EDCH_10MS None
TRUE, FALSE None
TRUE, FALSE None
TRUE, FALSE None
-8.2~17.3, step: 0.1 None
-8.2~17.3, step: 0.1 None
-8.2~17.3, step: 0.1 None
0~3 None
1, 2, 3, 4, 5, 6, 7, 8 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
0~127 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,

PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
PO_5/15, PO_6/15, PO_7/15, PO_8/15, PO_9/15, PO_11/15,
PO_12/15, PO_13/15, PO_15/15, PO_17/15, PO_19/15,
PO_21/15, PO_24/15, PO_27/15, PO_30/15, PO_34/15,
PO_38/15, PO_42/15, PO_47/15, PO_53/15, PO_60/15,
PO_67/15, PO_75/15, PO_84/15, PO_95/15, PO_106/15,
PO_119/15, PO_134/15, PO_150/15, PO_168/15, PO_189/15,
PO_212/15, PO_237/15, PO_267/15, PO_299/15, PO_336/15,
PO_377/15 None
0~37 None
0~37 None
TRUE, FALSE None
PO_8/15, PO_11/15, PO_15/15, PO_21/15, PO_30/15,

PO_42/15, PO_60/15, PO_84/15 PO_30/15
0~6 0
0~6 0
0~6 0
0~4 None
TRCH_EDCH_10MS None
TRCH_DCH, TRCH_HSDSCH None
1~5 None
0~3 None
AM, UM None
EDIT_SENDER_PARA, EDIT_RECEIVE_PARA None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 D32
50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600,
700, 800, 900, 1000 D350
NO_DISCARD None
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING None
50, 60, 70, 80, 90, 100, 120, 140, 160, 180, 200, 300, 400,
500, 700, 900 None
100, 250, 500, 750, 1000, 1250, 1500, 1750, 2000, 2500,
3000, 3500, 4000, 4500, 5000, 7500 None
1, 4, 6, 8, 12, 16, 24, 32 None

10, 20, 30, 40, 50, 60, 70, 80, 90, 100 None
2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40 None
50, 60, 70, 80, 90, 100, 120, 140, 160, 180, 200, 300, 400,
500, 700, 900 None
1, 4, 6, 8, 12, 16, 24, 32 None
1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 15, 20, 25, 30, 35, 40 None
1, 8, 16, 32, 64, 128, 256, 512, 768, 1024, 1536, 2047, 2560,
3072, 3584, 4095 D32
FALSE, TRUE 0
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
100, 200, 300, 400, 500, 750, 1000, 2000 None
FALSE, TRUE None
FALSE, TRUE 1
FALSE, TRUE 1
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
10, 20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 140,
150, 160, 170, 180, 190, 200, 210, 220, 230, 240, 250, 260,
270, 280, 290, 300, 310, 320, 330, 340, 350, 360, 370, 380,
390, 400, 410, 420, 430, 440, 450, 460, 470, 480, 490, 500,
510, 520, 530, 540, 550, 600, 650, 700, 750, 800, 850, 900,
950, 1000 None
1, 2, 4, 8, 16, 32, 64, 128 None
1, 4, 16, 64 None
50, 60, 70, 80, 85, 90, 95, 99 None
100, 200, 300, 400, 500, 750, 1000, 2000 None
1, 2, 4, 8, 16, 32, 64, 128 None
1, 4, 16, 64 None
MeasurementQuantity, Both MeasurementQuantity

0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 11, 13, 15, 17, 19 D3
0~512 30
RSRP, RSRQ RSRP
0~7.5, step: 0.5 4
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0

Value - 111) 36

Value - 111) 20
OFF. None
1~65535 9
8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D64
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D5000
250, 500, 1000, 2000, 4000, 8000, 16000 D1000
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D5000
250, 500, 1000, 2000, 4000, 8000, 16000 D16000
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D64
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D5000
250, 500, 1000, 2000, 4000, 8000, 16000 D1000

16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
8, 16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D64
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D5000
250, 500, 1000, 2000, 4000, 8000, 16000 D16000
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
10~100000, step: 10 30
0~384 8
0~1023 2
0~1023 4
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D1024
0, 10, 20, 40, 60, 80, 100, 120, 160, 200, 240, 320, 640, 1280,
2560, 5000 D0
16, 32, 64, 128, 256, 512, 1024, 2k, 3k, 4k, 6k, 8k, 12k, 16k,
24k, 32k, 48k, 64k, 96k, 128k, 192k, 256k, 384k, 512k, 768k D3k
1~65535 180
1~65535 5
1~65535 65535
1~65535 5
1~65535 180
1~65535 5
1~65535 5
1~65535 180
1~65535 5
1~65535 5
1~65535 180
1~65535 5
1~65535 180
OFF. UIA1-1
0~3 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~65535 None
0~3 None
INTERACTIVE, BACKGROUND, IMSSIGNALLING, PTT None
R99, HSPA None
0, 8, 16, 32, 64, 128, 144, 256, 384, 608, 1280, 2048, 2720,
5440 D64
0, 8, 16, 32, 64, 128, 144, 256, 384, 512, 768, 1024, 1536,
1800, 2048, 3600, 7200, 8640, 10100, 13900, 16000, 21000 D64
0~27900 0
3.4, 13.6, 27.2 D3.4
3.4, 13.6, 27.2 D3.4
0, 8, 16, 32, 64, 128, 144, 256, 384 D16
0, 8, 16, 32, 64, 128, 144, 256, 384 D16
0, 8, 16, 32, 64, 128, 144, 256, 384 D16
0, 8, 16, 32, 64, 128, 144, 256, 384 D16

0~100 90
5~20 5
0~100 100
5~20 5
0~100 0

ARP, TrafficClass ARP
NONE, DCH, HSPA NONE
digits with length of 6~15 None
OFF, ON OFF
ALGORITHM_OFF, ALGORITHM_ON ALGORITHM_OFF
PRIORITY1, PRIORITY2, PRIORITY3, PRIORITY4,

PRIORITY13, PRIORITY14, None
0~11 None
SAALLNK, IPOAPVC, AAL2PATH None
0, 2, 4, 8, 10, 12, 14, 16, 18, 20, 22, 24, 26 None
0~1399 None
0.0.0.0~255.255.255.255 None
0.0.0.0~255.255.255.255 None
0~4599 None
1~4294967295 None
NO_LOOP, LOCAL_LOOP None
1~65535 None
0~11 None
0~5, 8~27 None
0.0.0.0~255.255.255.255 None
2~4094 None
0~11 None
0~5, 8~27 None
UNI, IMA, FRAATM, NCOPT None
0~167 None
0~335 None
0~31 None
0~7 None
0~11 None
0~5, 8~27 None
UNI, IMA, FRAATM, NCOPT None
0~167 None
0~335 None
0~31 None
0~7 None
VPLCX, VCLCX None
0~4095 None
32~65535 None
0~4095 None
32~65535 None
100~1999 None
100~1999 None
0~1399 None
Recommended Value Impact
1 RNC
None Adjacent node
None None
None None
None AAL2 path
None None
None AAL2 path
None None
None None
None None
None None
None AAL2 path
None AAL2 path
None None
None None
None None
None AAL2 path
LOCAL None
0 BSC6900
10 AAL2 path
None None
None BSC6900
None Adjacent node
None BSC6900
YES BSC6900
7000 AAL2 path
5000 AAL2 path
5000 AAL2 path
3000 AAL2 path
5000 AAL2 path
5000 AAL2 path
5000 AAL2 path

10000 AAL2 path
10000 AAL2 path
None Adjacent node
None BSC6900
None BSC6900
None Adjacent node
Transmission resource
None group
None Adjacent node
None Adjacent node

None Adjacent node
None Adjacent node
None Adjacent node
None Adjacent node
None Adjacent node
None Adjacent node
None None
None Adjacent node
None Adjacent node
None Adjacent node
None Adjacent node
None Adjacent node

None Adjacent node
None Adjacent node
None BSC6900
None Adjacent node
None SAAL link
CS2 Adjacent node
None None
None BSC6900
None None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
ON BSC6900
None None
None None
None None
None None
None None
None None
None None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
90 BSC6900
ON BSC6900
None None
None BSC6900
None None
None None
None None
None ATM logical port
None None
None None
None BSC6900
ON ATM logical port
1 ATM logical port
0 None
None None
1 ATM logical port
0 None
None None
It is recommended that the service type of signaling link be CBR, the real-
time service be CBR or RTVBR, the non-real-time service be NRTVBR,
and the OAM data link be UBR_PLUS. PVC
None PVC
None PVC
None PVC
None PVC
1000 PVC
1024 PVC
None None
None None
None None
None None
None BSC6900
None BSC6900
None None
None None
None None
None Board
None None
None None
None None
None None
None Board
None None
None None
None None
None None
None None
None None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None BSC6900
None Board
None Ethernet port
None Board
None Ethernet port
1000 Ethernet port
None BSC6900
None BSC6900
None Board
0 Ethernet port
None Ethernet port
None None
None None
None Board
None Ethernet port
None Ethernet port
None Ethernet port
None BSC6900
None Ethernet port
None Ethernet port
None None
None None
None None
None None
None Board
None None
None Board
NO Board
None Board
None Board
None Board
None Board
AUTO BSC6900
None None
None None
LINE1_8K and LINE2_8K are most commonly used. None
None BSC6900
OFF BSC6900
None BSC6900
None None
None BSC6900
None Channelized optical port
ALL Channelized optical port

None None
None None
SPACE Board
None Cell
None Cell
None Cell
None Cell
None None
75 Board
85 Board
80 Board
85 Board
75 Board
90 Board
None Control plane link
None BSC6900
None BSC6900
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
1696 BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None BSC6900
None E1/T1 port

ALL E1/T1 port
None None
None E1/T1 port
E1_UNBA E1/T1 port
E1_CRC4_MULTI_FRAME E1/T1 port
None E1/T1 port
None E1/T1 port
None E1/T1 port
None E1/T1 port
None E1/T1 port
ON E1/T1 port
None BSC6900
None None
None BSC6900
None E1/T1 port
None E1/T1 port
None E1/T1 port
None None
None None
60 None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None None
None Board
None None
None None
None Board
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None Board
None Board
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None BSC6900
None Ethernet port
None Ethernet port
None Ethernet port
None BSC6900
None Ethernet port
None None
None BSC6900
None Ethernet port
None Ethernet port
None Ethernet port
ENABLE Ethernet port
AUTO Ethernet port

1500 Ethernet port
None Ethernet port
None Ethernet port
ON Ethernet port
None Ethernet port
OFF Board
O5E4_R1E4 Board
None Ethernet port
None Ethernet port
V7 Ethernet port
None None
None None
None Ethernet port
None BSC6900
None BSC6900
None Ethernet port
LOAD_SHARING None
None None
NON-REVERTIVE None
None Ethernet port
0 Ethernet port
ON Ethernet port
0 Ethernet port
V7 Ethernet port
None BSC6900
None BSC6900
None Ethernet port
None Ethernet port
None Ethernet port
None Ethernet port
None BSC6900
None BSC6900
None Ethernet port
None BSC6900
None Ethernet port
LOAD_SHARING None
None None
10 BSC6900
30 BSC6900
OFF BSC6900
None None
None None
SOFTWARE_CONTROL BSC6900
None BSC6900
None None
10 None
4 None
95 Board
60 Board
50 Board
60 Board
50 Board
60 Board
50 Board
85 Board
70 Board
70 Board
60 Board
80 Board
70 Board
90 Board
75 Board
95 Board
85 Board
95 Board
85 Board
95 Board
85 Board
85 Board
70 Board
90 Board
80 Board
95 Board
80 Board
60 Board
5 Board
80 Board
70 Board
60 Board
50 Board
70 Board
60 Board
85 Board
75 Board
90 Board
85 Board
60 Board
50 Board
None None
10 None
95 Board
60 Board
50 Board
60 Board
50 Board
60 Board
50 Board
85 Board
70 Board
70 Board
60 Board
95 Board
85 Board
95 Board
85 Board
95 Board
85 Board
85 Board
70 Board
90 Board
80 Board
95 Board
80 Board
80 Board
70 Board
75 Board
65 Board
None None
None None
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
ON Board
70 Board
ON Board
ON Board
ON Board
ON Board
None None
None BSC6900
None BSC6900
None BSC6900
None E1/T1 port
None Fractional link
None None
ON Fractional link
1 Fractional link
0 Fractional link
None None
None None
None None
None None
None BSC6900
None BSC6900
AUTO BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
AUTO BSC6900
DEFAULTPORT BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None None
10 None
1 None
DEG None
MET None
None None
None None
None BSC6900
None None
None None
None BSC6900
None None
None None
None None
None BSC6900
None Ethernet port
None Ethernet port
None Ethernet port
None None
None BSC6900
None BSC6900
None IMA group

1 IMA group
None IMA group
D128 IMA group
25(AEUa),200(AOUa/AOUc) IMA group
V1.1 IMA group
ON IMA group
1 IMA group
None IMA group
0 IMA group
None None
None None
None None
None BSC6900
None IMA link

None IMA group
None IMA group
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
OFF BSC6900
120 BSC6900
None BSC6900
None BSC6900
None BSC6900
None Ethernet port

ON None
1000 None
800 None
ON None
None None
None BSC6900
None IP logical port
None None
None None
None None
None BSC6900
25 IP logical port
4500 IP logical port
0 IP logical port
96 IP logical port
5 IP logical port
10 IP logical port
5 IP logical port
120 IP logical port
30 IP logical port
2 IP logical port
25 IP logical port
1 IP logical port
4 IP logical port
8 IP logical port
3 IP logical port
ON IP logical port
0 IP logical port
20 IP logical port
30 IP logical port
2 IP logical port
None None
None None
None IP Path
None IP path
None IP Path
None IP Path
None IP Path
352 IP Path
1031 IP Path
2 IP Path
None None
None IP Path
None None
None IP Path
None BSC6900
None BSC6900
None IPoA PVC
None None
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None IPoA PVC
None Adjacent node
None IP path
None BSC6900
None IP path
QoS IP path
None IP path
None IP path
255.255.255.255 IP path
None IP path
None IP path
NULL IP path
None IP path
None IP path
None AAL2 path
2 BSC6900
DISABLE IP path
None BSC6900
DISABLED IP path
None IP path
5 IP path
5 IP path
64 IP path
UDP IP path
None IP path
None IP Path
None None
None BSC6900
None None
None None
None BSC6900
None IP route
None IP route
None IP route
None IP route
None IP route
None BSC6900
None None
None BSC6900
None None
None Ethernet port
None None
None None
None None
None None
None None
None None
None None
90 None
70 None
UMTS BSC6900
YES BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
none BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
DISABLE BSC6900
DISABLE BSC6900
None BSC6900
None BSC6900
None BSC6900
30 BSC6900
50000 BSC6900
None BSC6900
None SCCP
None SCCP
None SCCP
None SCCP
4294967295 SCCP
None None
None SCCP
None SCCP
None SCCP
4294967295 SCCP
None None
None SCCP
None SCCP
B1111 SCCP
M3UA_LOADSHARE_MOD SCCP
M3UA_ASP SCCP
5 SCCP
None None
None SCCP
None BSC6900
None BSC6900
None BSC6900
None Subsystem
None SCTP link
0 None
M3UA_MASTER_MOD BSC6900
None None
None SCCP
None SCCP
0 SCCP
None None
None None
None None
None None
None None
None BSC6900
None BSC6900
IP Board
None MP group
MCPPP MP group
NO MP group
None MP group
None BSC6900
None MP group
None MP group
LONG MP group
None MP group
None MP group
UDP/IP_HC MP group
Enable MP link
Enable PPP link
Disable MP group
None MP group
None MP group
None MP group
ON MP group
0 MP group
0 MP group
NO_V MP group
None MP group
None MP group
None MP group
2 None
OFF Board
O5E4_R1E4 Board
OFF Board
ERR_PFM_1E5 Board
ERR_PFM_5E6 Board
None None
None None
8 MP group
64 MP group
256 MP group
1000 MP group
ERR_PFM_1E5 Board
ERR_PFM_5E6 Board
None None
None BSC6900
None BSC6900
None MP group
None MP link
None MP link
None MP link
3 MP link
2 PPP link
16bit MP link
None None
None None
None None
None None
None None
None None
None Board
None MSP protect group
600 MSP protect group
DISABLE MSP protect group
1.00E-06 MSP protect group
None None
None None
None Board
None SCCP
None SCCP
B1111 SCCP
OFF MTP3 link
None None
None SCCP
None MTP3 link
None BSC6900
None group
None SAAL link
0 None
10 MTP3 link
170 MTP3 link
None None
None SCCP
None SCCP
0 SCCP
None None
1200 MTP3 link
2000 MTP3 link
1200 MTP3 link
1200 MTP3 link
1200 MTP3 link
1200 MTP3 link
60000 MTP3 link
1500 MTP3 link
1500 MTP3 link
3000 MTP3 link
1500 MTP3 link
360000 MTP3 link
360000 MTP3 link
12000 MTP3 link
60000 MTP3 link
35000 MTP3 link
None None
None SCCP
None SCCP
WNF SCCP
None SCCP
None SCCP
None SCCP
B0000 SCCP
YES SCCP
OFF SCCP
None SCCP
None SCCP
ITUT SCCP
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
Guests BSC6900
None BSC6900
NOLIMIT BSC6900
None BSC6900
None BSC6900
NOLIMIT BSC6900
None BSC6900
None BSC6900
NOLIMIT BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None SCCP
None SCCP
None SCCP
WNF SCCP
None SCCP
None SCCP
OFF SCCP
OFF BSC6900
None None
None None
None None
UMTS BSC6900
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None BSC6900
None None
None BSC6900
None Board
None Board
None Board
None Board
None Board
None Board
None Board
16byte Board
Character_String None
16byte Board
SBS 155 Board
16byte Board
SBS 155 Board
16byte Board
16byte Board
SBS 155 Board
16byte Board
SBS 155 Board
None Board
None Board
None Board
None Board
None Board
OFF Board
None Board
SPACE Board
AU4 Channelized optical port
None None
None BSC6900
None Loopback optical port
None Loopback optical port
Step_by_Step None
None None
None None
None None
None BSC6900
None E1/T1 link

None Board
48 SCTP link
None BSC6900
None BSC6900
2 BSC6900
IP:25; ATM:30 BSC6900
IP:15; ATM:20 BSC6900
IP:60; ATM:45 BSC6900
IP:25; ATM:30 BSC6900
IP:15; ATM:20 BSC6900
IP:60; ATM:45 BSC6900
IP:25; ATM:30 BSC6900
IP:15; ATM:20 BSC6900
IP:60; ATM:45 BSC6900
IP:25; ATM:50 BSC6900

IP:15; ATM:25 BSC6900
IP:60; ATM:80 BSC6900
50 BSC6900
25 BSC6900
80 BSC6900
50 BSC6900
25 BSC6900
80 BSC6900
None None
None BSC6900
None BSC6900
IP Board
None PPP link
None PPP link

None PPP link
NO MP group
None BSC6900
None BSC6900
None PPP link
None BSC6900
UDP/IP_HC PPP link
Enable PPP link

Enable PPP link
Disable MP group
64 PPP link
256 PPP link
1000 MP group
NO_V PPP link
None PPP link
None PPP link
None PPP link
3 PPP link
2 PPP link
ON PPP link
0 PPP link
0 PPP link
16bit PPP link
2 PPP link
OFF Board
O5E4_R1E4 Board
None None
None None
Enable PPP link
1000 PPP link
None None
None BSC6900
None MP group
None MP group
None PPP link
None None
10 None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None None
None BSC6900
None Port queue
None Port queue
None Port queue
None Port queue
None Port queue
None Port queue
None Port queue
OFF BSC6900
None BSC6900
None BSC6900
None BSC6900
None Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
None BSC6900
None group
None group
None group
None group
None group
None group
None group
None group
None group
None group
None group
0 BSC6900
None BSC6900
None group
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link
None SAAL link

None SAAL link
None SAAL link
None SAAL link
MPS_NEUTRAL SAAL link
1000(UNI), 200(NNI) SAAL link
2 SAAL link
30 SAAL link
10 SAAL link
60 SAAL link
1500 SAAL link
0 SAAL link
4 SAAL link

67 SAAL link
100 SAAL link
90 SCCP
90 SCCP
720 SCCP
15 SCCP
15 SCCP
60 SCCP
1440 SCCP
15 SCCP
20 SCCP
60 SCCP
90 SCCP
60 SCCP
30 SCCP
10 SCCP
15 SCCP
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None Cell
5 Physical channel
0 Cell
None BSC6900
None group
None SCTP link
None SCTP link
None SCTP link
48 SCTP link
None SCTP link

None SCTP link
None SCTP link
None SCTP link
None SCTP link
None SCTP link
None SCTP link
None SCTP link
None SCTP link
1000(application type is NBAP), 150(application type is M3UA) SCTP link
3000 SCTP link
1000 SCTP link
12 SCTP link
25 SCTP link
NO SCTP link
NO SCTP link
CRC32 SCTP link
800 SCTP link
DISABLE SCTP link
None BSC6900
DISABLE SCTP link
None BSC6900
UNAVAILABLE SCTP link
YES SCTP link
10 SCTP link
NO SCTP link
5000(application type is NBAP), 1000(application type is M3UA),
1000(application type is BBAP) SCTP link
10(application type is NBAP), 4(application type is M3UA), 10(application

type is BBAP) SCTP link
5(application type is NBAP), 2(application type is M3UA), 5(application
type is BBAP) SCTP link
58080 SCTP link
2905 SCTP link
58000 SCTP link
None None
None None
None None
None None
None None
70 Board
60 Board
85 Board
75 Board
90 Board
80 Board
75 Board
65 Board
75 Board
65 Board
75 Board
65 Board
None None
ON None
ON None
ON None
None BSC6900
None BSC6900
None BSC6900
OFF BSC6900
OFF BSC6900
OFF BSC6900
OFF BSC6900
OFF BSC6900
OFF BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
NO None
SCUa None
None None
None None
None BSC6900
None BSC6900
None BSC6900
ENABLED BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
30 BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None BSC6900
None BSC6900
ON BSC6900
ON BSC6900
ON BSC6900
ON BSC6900
ON BSC6900
ON BSC6900
ON BSC6900
OFF BSC6900
ON BSC6900
ON BSC6900
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None BSC6900
None BSC6900
70 BSC6900
70 BSC6900
15 BSC6900
15 BSC6900
100 BSC6900
15 BSC6900
15 BSC6900
70 BSC6900
70 BSC6900
100 BSC6900
100 BSC6900
100 BSC6900
100 BSC6900
70 BSC6900
70 BSC6900
100 BSC6900
100 BSC6900
40 BSC6900
40 BSC6900
40 BSC6900
40 BSC6900
15 BSC6900
15 BSC6900
70 Adjacent node
70 BSC6900
100 BSC6900
40 BSC6900
40 BSC6900
15 BSC6900
15 BSC6900
70 BSC6900
70 BSC6900
100 BSC6900
40 BSC6900
40 BSC6900
20 BSC6900
20 BSC6900
20 BSC6900
None BSC6900
None BSC6900
None BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
0 BSC6900
5 BSC6900
5 BSC6900
15 BSC6900
15 BSC6900
20 BSC6900
20 BSC6900
0 BSC6900
0 BSC6900
1 BSC6900
1 BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
When the interface type is Iub, transmission type is ATM or dual stack,
the parameter is RT_VBR; transmission type is IP or Hybrid IP, the
parameter is EF.
When the interface type is Iur, transmission type is ATM, the parameter is
RT_VBR; transmission type is IP, the parameter is EF. BSC6900
When the interface type is Iub, transmission type is ATM or IP, the
parameter is NULL; transmission type is dual stack, the parameter is EF;
transmission type is Hybrid IP, the parameter is LQEF.
When the interface type is Iur, transmission type is ATM or IP, the
parameter is NULL. BSC6900
parameter is EF.
parameter is EF.
parameter is EF.
RT_VBR; When the interface type is Iu-CS, transmission type is ATM, the
parameter is RT_VBR; transmission type is IP, the parameter is EF. BSC6900
parameter is NULL.
When the interface type is Iu-CS, transmission type is ATM or IP, the
parameter is AF43.
RT_VBR; transmission type is IP, the parameter is AF43.
When the interface type is Iu-CS, transmission type is ATM, the
parameter is RT_VBR; transmission type is IP, the parameter is AF43. BSC6900
parameter is NULL; transmission type is dual stack, the parameter is
AF43; transmission type is Hybrid IP, the parameter is LQAF43.
parameter is NULL.
parameter is AF43.
When the interface type is Iu-CS, transmission type is ATM, the
parameter is RT_VBR; transmission type is IP, the parameter is AF43. BSC6900
parameter is NULL.
parameter is AF43.
When the interface type is Iu-PS, the parameter is AF43. BSC6900
parameter is NULL.
When the interface type is Iu-PS, the parameter is NULL. BSC6900
parameter is AF43.
parameter is NULL.
parameter is AF23.
parameter is NULL.
parameter is AF23.
parameter is NULL.
parameter is AF23.
parameter is NULL.
parameter is AF23.
parameter is NULL.
parameter is EF.
parameter is EF.
parameter is AF43.
RT_VBR; transmission type is IP, the parameter is AF43. BSC6900
parameter is AF43.
parameter is AF43.
When the interface type is Iub, transmission type is ATM, the parameter
is UBR; transmission type is dual stack or IP, the parameter is AF13;
transmission type is dual stack or Hybrid IP, the parameter is LQAF13.
UBR; transmission type is IP, the parameter is AF13. BSC6900
UBR; transmission type is Hybrid IP, the parameter is AF13.
parameter is EF.
parameter is EF.
parameter is AF43.
parameter is AF43.
parameter is AF43.
None None
None BSC6900
None E1/T1 port
None E1/T1 port
None E1/T1 port
None E1/T1 port
None E1/T1 port

None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None RNC
None Cell
None Cell
0 Cell
0 Cell
-50 Cell
D0 Cell
D3 Cell
0 Cell
None Cell
-18 Cell
1 Cell
0 Cell
0 Cell
None Cell
0 Cell
0 Cell
None Cell
OFF RNC
2 RNC
50 RNC
30 RNC
1 RNC
None RNC
10 RNC
10 RNC
50 RNC
50 RNC
100 RNC
100 RNC
100 RNC
100 RNC
10 RNC
10 RNC
10 RNC
10 RNC
100 RNC
50 RNC
50 RNC
100 RNC
100 RNC
100 RNC
100 RNC
100 RNC
100 RNC
None Cell
4 Cell
6 Physical channel
1 Cell
0 Physical channel
None Cell
-6 Physical channel
70 None
60 None
80 None
70 None
50 RNC
50 RNC
120 RNC
120 RNC
1000 RNC
3000 RNC
NBAMR_BITRATE_12.20K Cell
50 RNC
50 RNC
120 RNC
120 RNC
1000 RNC
3000 RNC
WBAMR_BITRATE_23.85K Cell
None Subsystem
None Subsystem
OFF Subsystem
OFF Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
OFF Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Subsystem
None Cell
0 Transport channel
-20 Transport channel
None RNC
None RNC
0 RNC
0 RNC
SYS_LEVEL:ON
NODEB_LEVEL:ON
CELL_LEVEL:ON RNC
ON RNC
3 RNC
180 RNC
60 RNC
60 RNC
100 RNC
60 RNC
20 RNC
20 RNC
45 RNC
15 RNC
15 RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None Subsystem
None Subsystem
None RNC
None Subsystem
None Subsystem
None Subsystem
0 RNC
0 RNC
CELL RNC
None RNC
None RNC
None RNC
None RNC
0 RNC
CellNormal RNC
Normal RNC
1 RNC
10 RNC
English RNC
0 RNC
Earthquake RNC
None RNC
None RNC
None NodeB
None NodeB
None NodeB
None SAAL link
None SCTP link
SAAL NodeB
None NodeB
None NodeB
None None
None None
None Cell
None Cell
430 Cell
None Cell
Invalid Cell
None Cell
None RNC
None Cell
None Cell
None Cell
None Cell
5 Cell
50 Cell
50 Cell
None Cell
None Cell
None Cell
None NodeB
None NodeB
None RNC
None RNC
None RNC
None RNC
STTD_not_Supported Cell
CP1_not_Supported Cell
OFFSET1 Cell
None Cell
None Cell
None Cell
None Cell
None Cell
0 Cell
0 Cell
None Cell
430 Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
0 Cell
None Cell
None Cell
330 Physical channel
330 Cell
-50 Physical channel
0 Cell
None Cell
None Cell
None Cell
None NodeB
None NodeB
1 None
346 Cell
313 Cell
0 Transport channel
-130 Cell
-7 Cell
None Cell
NOT_RESERVED Cell
NOT_RESERVED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
NOT_BARRED Cell
None Cell
ALLOWED Cell
D320 Cell
None Cell
NOT_ALLOWED Cell
D1280 Cell
None Cell
None RNC
None RNC
None RNC
None RNC
None Cell
None Cell
None Cell
None Cell
None Cell
ALGORITHM_DEPEND_ON_LCG Cell
None Cell
E_F_DPCH_OFF Cell
None Cell
NBM_LDC_MATCH_UE_ONLY Cell
None Cell
0 Cell
0 Cell
ON Cell
None Cell
None Cell
None Cell
None Cell
TU Cell
75 Cell
75 Cell
60 Cell
80 Cell
80 Cell
75 Cell
80 Cell
85 Cell
83 Cell
90 Cell
0 Cell
0 Cell
95 Cell
80 Cell
100 Cell
100 Cell
100 Cell
0 Cell
70 Cell
30 Cell
64 Cell
24 Cell
24 Cell
24 Cell
24 Cell
61 Cell
-13 Cell
ON Cell
120 Cell
0 Cell
20 Cell
0 Cell
0 Cell
20 Cell
16 Cell
60 Cell
40 Cell
SF16 Cell
SF32 Cell
01&00&00 Cell
06&00&00 Cell
5 Cell
100 Cell
48 Cell
40 Cell
48 Cell
20 Cell
100 Cell
100 Cell
None Cell
None Cell
None RNC
None Cell
OFF Cell
None Cell
None Cell
WALKING_SPEED_AND_HOT_SPOT_CELL Cell
D64 Cell
D64 Cell
None Cell
10 Cell
20 Cell
D64 Cell
D64 Cell
None None
None Cell
None Cell
None Cell
None Cell
None None
2 Cell
OFF Cell
OFF Cell
OFF Cell
UserNumber Cell
35 Cell
100 Cell
OFF Cell
SF8 Cell
13 Cell
DependOnNCell Cell
None Cell
None Cell
None Cell
ON RNC
25 RNC
OFF Cell
None None
OFF RNC
OFF RNC
10 RNC
10 RNC
25 RNC
17 RNC
15 RNC
25 RNC
20 RNC
15 RNC
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
CONDITIONALSHUTDOWN Cell
1 Cell
0 Cell
0 Cell
20 Cell
None Cell
None Cell
EDRXT321_100 Cell
EDRXCYCLE_8 Cell
EDRXBURST_1 Cell
INTERRUPTION_CFG Cell
None Cell
10 Cell
-30 Cell
0 Cell
32 Cell
512 Cell
32 Cell
512 Cell
32 Cell
512 Cell
32 Cell
512 Cell
32 Cell
512 Cell
32 Cell
512 Cell
32 Cell
512 Cell
None Cell
1 Cell
19 Cell
-30 Cell
15 Cell
2 Cell
35 Cell
10 Cell
32 Cell
None None
D8 Cell
D8 Cell
0 Cell
41 Cell
5000 Cell
None Cell
None Cell
None RNC
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
ACTIVE Cell
None Cell
NOT_USED Cell
0 Cell
0 Cell
0 Cell
20 Cell
D60 Cell
8 Cell
D20 Cell
0 Cell
None Cell
OFF Cell
180 Cell
15 Cell
60 Cell
240 Cell
3 Cell
10 Cell
None Cell
SIMINTERFREQRAT Cell
COEXIST_MEAS_THD_CHOICE_INTERFREQ Cell
OFF Cell
OFF Cell
None Cell
Automatic Cell
5 Cell
5 Cell
1 Cell
4 Cell
0 Cell
2.5dB Cell
Mode0 Cell
ON Cell
3 Cell
5 Cell
None Cell
None Cell
None Cell
PO_24/15 Cell
PO_24/15 Cell
1 Cell
1 Cell
D2 Cell
D2 Cell
D8 Cell
D2 Cell
D4 Cell
None Cell
1 Cell
1 Cell
75 Cell
0 Cell
None RNC
None Cell
None Cell
None Cell
PERIODICAL_REPORTING Cell
For low speed(5km/h):Range is D4~D6, the recommended value is D5;

for middle speed(50km/h):Range is D3~D4, the recommended value is
D4;
for high speed(120km/h):Range is D2~D4, the recommended value is D2;
universal value:Range is D3~D6, the recommended value is D3. Cell
D500 Cell
4 Cell
4 Cell
4 Cell
0 Cell
0 Cell
D0 Cell
D320 Cell
D1280 Cell
0 Cell
-14 Cell
-12 Cell
-14 Cell
-14 Cell
-12 Cell
-12 Cell
-95 Cell
-92 Cell
-95 Cell
-95 Cell
-92 Cell
-92 Cell
-12 Cell
-12 Cell
-12 Cell
-92 Cell
-92 Cell
-92 Cell
-12 Cell
-12 Cell
-12 Cell
-92 Cell
-92 Cell
-92 Cell
60 Cell
1 Cell
4 Cell
0 Cell
None Cell

D4;
6 Cell
D640 Cell
-16 Cell
60 Cell
4 Cell
1 Cell
None Cell
D3 Cell
AUTO Cell
D3 Cell
0 Cell
D1000 Cell
4 Cell
4 Cell
4 Cell
0 Cell
D320 Cell
D1280 Cell
D0 Cell
0 Cell
0 Cell
REQUIRED Cell
-14 Cell
-12 Cell
-15 Cell
-15 Cell
-13 Cell
-13 Cell
-100 Cell
-97 Cell
-110 Cell
-110 Cell
-107 Cell
-107 Cell
16 Cell
16 Cell
16 Cell
-12 Cell
-13 Cell
-13 Cell
-97 Cell
-107 Cell
-107 Cell
60 Cell
0 Cell
0 Cell
1 Cell
4 Cell
3 Cell
30 Cell
None Cell
D3 Cell
0 Cell
D640 Cell
REQUIRED Cell
21 Cell
21 Cell
16 Cell
60 Cell
80 Cell
60 Cell
4 Cell
1 Cell
3 Cell
30 Cell
None RNC
None Cell
D3 Cell
CPICH_EC/NO Cell
D16 Cell
D4000 Cell
D16 Cell
D4000 Cell
D64 Cell
D1000 Cell
6 Cell
6 Cell
6 Cell
12 Cell
12 Cell
12 Cell
-24 Cell
-115 Cell
0 Cell
0 Cell
8 Cell
8 Cell
8 Cell
8 Cell
0 Cell
D320 Cell
D640 Cell
D640 Cell
D640 Cell
D640 Cell
D640 Cell
-24 Cell
3 Cell
-115 Cell
None Cell
2 Cell
90 Cell
30 Cell
None Cell
55 Cell
45 Cell
70 Cell
60 Cell
95 Cell
85 Cell
95 Cell
85 Cell
1000 Cell
70 Cell
50 Cell
90 Cell
70 Cell
150 Cell
None Cell
CodeAdj Cell
InterFreqLDHO Cell
BERateRed Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
1 Cell
1 Cell
3 Cell
1 Cell
1 Cell
3 Cell
1 Cell
InterFreqLDHO Cell
BERateRed Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
NoAct Cell
1 Cell
1 Cell
3 Cell
1 Cell
1 Cell
3 Cell
1 Cell
20 Cell
20 Cell
200000 Cell
200000 Cell
1 Cell
SF8 Cell
0 Cell
1 Cell
SF8 Cell
SF8 Cell
13 Cell
0 Cell
OFF Cell
None Cell
2SF4 Cell
BLINDHO Cell
None None
INTELLIGENT_INTERFREQ_UE_TYPE_STEERING:OFF Cell
None Cell
CSAMR_INTERFREQ:OFF, CSNONAMR_INTERFREQ:OFF,
PSR99_INTERFREQ:OFF, PSHSPA_INTERFREQ:OFF Cell
80 Cell
80 Cell

D4;
EVENT_TRIGGER Cell
CPICH_EC/NO Cell
D500 Cell
0 Cell
0 Cell
6 Cell
D640 Cell
-16 Cell
-92 Cell
1 Cell
3 Cell
None Cell
CSAMR_INTERRAT:OFF Cell
80 Cell
80 Cell
D3 Cell
EVENT_TRIGGER Cell
D1000 Cell
REQUIRED Cell
0 Cell
0 Cell
0 Cell
D640 Cell
21 Cell
1 Cell
ALL_USER Cell
3 Cell
30 Cell
None Cell
None RNC
None RNC
10 Cell
80 Cell
50 Cell
35 Cell
10 Cell
None Cell
PTM RNC
4 RNC
3 RNC
None Cell
None RNC
None RNC
None Cell
None RNC
None RNC
0 Physical channel
None Cell
None Cell
-7 Cell
0 Cell
None Cell
None Cell
ON Cell
None None
ON Cell
10 Cell
D3000 RNC
-92 Cell
-12 Cell
10 Cell
None Cell
6 Cell
D3000 Cell
-92 Cell
-12 Cell
None Cell
REQUIRE Cell
INTER_FREQ_AND_INTER_RAT Cell
INTER_FREQ_AND_INTER_RAT Cell
None RNC
None Cell
None Cell
None Cell
None None
None Cell
None Cell
None Cell
2 Cell
2 Cell
D6 Cell
-70 Cell
1 Cell
D0 Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
3 Cell
3 Cell
3 Cell
3 Cell
68 Cell
130 Cell
3000 Cell
5000 Cell
0 Cell
0 Cell
MBMS_REL Cell
1 Cell
1 Cell
0 Cell
None Cell
45 Cell
70 Cell
5 Cell
-2 Cell
2 Cell
-4 Cell
-4 Cell
4 Cell
4 Cell
None Cell
5 Cell
20 Cell
20 Cell
CPICH_RSCP Cell
None Cell
D320 Cell
D320 Cell
D320 Cell
D320 Cell
D240 Cell
D640 Cell
D640 Cell
D240 Cell
D640 Cell
D2560 Cell
D1280 Cell
D1280 Cell
D240 Cell
D19 Cell
D1 Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
None None
None Cell
None Cell
0 Cell
AMR:50;Other:0 Cell
DependOnNCell Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None RAB
None RAB
None Cell
None Cell
None Cell
None Cell
CPICH_ECNO Cell
2 Cell
2 Cell
1 Cell
1 Cell
1 Cell
-18 Cell
-58 Cell
0 Cell
None Cell
24 Cell
5 Cell
4 Cell
5 Cell
4 Cell
2 Cell
255 Cell
255 Cell
255 Cell
NOT_CONFIGURED Cell
NotUsed Cell
8 Cell
NotUsed Cell
255 Cell
255 Cell
255 Cell
255 Cell
255 Cell
255 Cell
4 Cell
2 Cell
2 Cell
1 Cell
None Cell
None Cell
None Cell
None RNC
None RNC
30 Cell
None Cell
4 Cell
D0 Cell
36 Cell
20 Cell
None Cell
95 Cell
85 Cell
2 Cell
None Cell
None RNC
None RNC
1024 RNC
3 RNC
60 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
None Cell
-7 Cell
-6 Cell
None RNC
None RNC
None RNC
None RNC
None Cell
None None
None None
None None
None RNC
None Cell
ON Cell
OFF RNC
10 RNC
80 BSC6900
D64 Cell
D64 Cell
WALKING_SPEED_AND_HOT_SPOT_CELL Cell
0 RNC
D8 RNC
1 RNC
BasedOnUECap RNC
0 RNC
None RNC
10 RNC
ALLOWED RNC
MODE2 RNC
6 RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
OFF RNC
1 RNC
OFF RNC
None RNC
None RNC
OFF RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None Cell
None Cell
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
180 RNC
5 RNC
2 RNC
5 RNC
10 RNC
D2000 RNC
3 RNC
D2000 RNC
3 RNC
D30 RNC
D30 RNC
D40 RNC
1 RNC
5 RNC
6 RNC
D1 RNC
3 RNC
D50 RNC
D0 RNC
D0 RNC
D1 RNC
D30 RNC
D600 RNC
D1 RNC
INVALID RNC
CFG_DL_BLIND_DETECTION_SWITCH:ON,
CFG_HSDPA_64QAM_SWITCH:ON, CFG_HSDPA_DC_SWITCH:OFF,
CFG_HSDPA_MIMO_SWITCH:ON,
CFG_HSDPA_MIMO_WITH_64QAM_SWITCH:OFF,
CFG_HSPA_DTX_DRX_SWITCH:OFF,
CFG_HSPA_HSSCCH_LESS_OP_SWITCH:OFF,
CFG_HSUPA_16QAM_SWITCH:OFF,
CFG_IMS_SUPPORT_SWITCH:ON,
CFG_LOSSLESS_DLRLC_PDUSIZECHG_SWITCH:OFF,
CFG_LOSSLESS_RELOC_CFG_SWITCH:OFF,
CFG_MULTI_RAB_SWITCH:ON,
CFG_PDCP_IPV6_HEAD_COMPRESS_SWITCH:OFF,
CFG_PDCP_RFC2507_HC_SWITCH:OFF,
CFG_PDCP_RFC3095_HC_SWITCH:OFF, CFG_PTT_SWITCH:OFF,
CFG_RAB_REL_RMV_HSPAPLUS_SWITCH:OFF,
CFG_EDPCCH_BOOSTING_SWITCH:OFF,
CFG_HSDPA_DCMIMO_SWITCH:OFF,
CFG_FREE_USER_SWITCH:OFF,
CFG_DC_MIMO_DYNAMIC_SELECT_SWITCH:OFF RNC
DRA_AQM_SWITCH:OFF,
DRA_BASE_ADM_CE_BE_TTI_L2_OPT_SWITCH:ON,
DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH:ON,
DRA_BASE_COVER_BE_TTI_L2_OPT_SWITCH:OFF,
DRA_BASE_COVER_BE_TTI_RECFG_SWITCH:ON,
DRA_BASE_RES_BE_TTI_L2_OPT_SWITCH:OFF,
DRA_BASE_RES_BE_TTI_RECFG_SWITCH:ON,
DRA_DCCC_SWITCH:ON,
DRA_HSDPA_DL_FLOW_CONTROL_SWITCH:OFF,
DRA_HSDPA_STATE_TRANS_SWITCH:OFF,
DRA_HSUPA_DCCC_SWITCH:ON,
DRA_HSUPA_STATE_TRANS_SWITCH:OFF,
DRA_IP_SERVICE_QOS_SWITCH:OFF,
DRA_PS_BE_STATE_TRANS_SWITCH:ON,
DRA_PS_NON_BE_STATE_TRANS_SWITCH:OFF,
DRA_R99_DL_FLOW_CONTROL_SWITCH:OFF,
DRA_THROUGHPUT_DCCC_SWITCH:OFF,
DRA_VOICE_SAVE_CE_SWITCH:OFF,
DRA_VOICE_TTI_RECFG_SWITCH:ON RNC
CS_AMRC_SWITCH:OFF,
CS_HANDOVER_TO_UTRAN_DEFAULT_CFG_SWITCH:ON,
CS_IUUP_V2_SUPPORT_SWITCH:OFF RNC
PC_CFG_ED_POWER_INTERPOLATION_SWITCH:OFF,
PC_DL_INNER_LOOP_PC_ACTIVE_SWITCH:ON,
PC_DOWNLINK_POWER_BALANCE_SWITCH:ON,
PC_EFACH_ECN0_DYN_ADJ_SWITCH:OFF,
PC_FP_MULTI_RLS_IND_SWITCH:ON,
PC_HSUPA_COVER_EN_AT_POLIMIT_SWITCH:OFF,
PC_HSUPA_DATA_CH_PO_ADAPTIVE_ADJ_SWITCH:OFF,
PC_HSUPA_HARQNUM_AUTO_ADJUST_SWITCH:OFF,
PC_INNER_LOOP_LMTED_PWR_INC_SWITCH:OFF,
PC_OLPC_SWITCH:ON,
PC_RL_RECFG_SIR_TARGET_CARRY_SWITCH:OFF,
PC_SIG_DCH_OLPC_SWITCH:OFF,
PC_UL_SIRERR_HIGH_REL_UE_SWITCH:OFF RNC
CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH:OFF,
CMP_IU_QOS_ASYMMETRY_IND_COMPAT_SWITCH:OFF,
CMP_IU_SYSHOIN_CMP_IUUP_FIXTO1_SWITCH:OFF,
CMP_IUR_H2D_FOR_LOWR5_NRNCCELL_SWITCH:OFF,
CMP_IUR_SHO_DIVCTRL_SWITCH:OFF,
CMP_UU_ADJACENT_FREQ_CM_SWITCH:OFF,
CMP_UU_AMR_DRD_HHO_COMPAT_SWITCH:OFF,
CMP_UU_AMR_SID_MUST_CFG_SWITCH:OFF,
CMP_UU_FDPCH_COMPAT_SWITCH:OFF,
CMP_UU_IGNORE_UE_RLC_CAP_SWITCH:ON,
CMP_UU_INTRA_FREQ_MC_BESTCELL_CIO_SWITCH:OFF,
CMP_UU_IOS_CELL_SYNC_INFO_REPORT_SWITCH:OFF,
CMP_UU_SERV_CELL_CHG_WITH_ASU_SWITCH:OFF,
CMP_UU_SERV_CELL_CHG_WITH_RB_MOD_SWITCH:ON,
CMP_UU_VOIP_UP_PROC_AS_NORMAL_PS_SWITCH:ON,
CMP_F2F_RLC_ONESIDE_REBUILD_SWITCH:OFF,
CMP_D2F_RLC_ONESIDE_REBUILD_SWITCH:OFF,
CMP_RAB_5_CFG_ROHC_SWITCH:OFF,
CMP_HSUPA_MACD_FLOW_MUL_SWITCH:OFF,
CMP_SMLC_RSLT_MODE_TYPE_SWITCH:OFF RNC
MAP_HSUPA_TTI_2MS_SWITCH:OFF,
MAP_INTER_RAT_PS_IN_CHANLE_LIMIT_SWITCH:OFF,
MAP_PS_BE_ON_E_FACH_SWITCH:OFF,
MAP_PS_STREAM_ON_E_FACH_SWITCH:OFF,
MAP_PS_STREAM_ON_HSDPA_SWITCH:OFF,
MAP_PS_STREAM_ON_HSUPA_SWITCH:OFF,
MAP_SRB_ON_DCH_OR_FACH_CS_RRC_SWITCH:OFF RNC
PS_BE_EXTRA_LOW_RATE_ACCESS_SWITCH:OFF,
PS_BE_INIT_RATE_DYNAMIC_CFG_SWITCH:OFF,
PS_BE_IU_QOS_NEG_SWITCH:OFF,
PS_RAB_DOWNSIZING_SWITCH:ON,
PS_STREAM_IU_QOS_NEG_SWITCH:OFF,
PS_BE_STRICT_IU_QOS_NEG_SWITCH:OFF RNC
DR_RRC_DRD_SWITCH:ON,DR_RAB_SING_DRD_SWITCH:ON,DR_R
AB_COMB_DRD_SWITCH:OFF,DR_INTER_RAT_DRD_SWITCH:ON RNC
HO_ALGO_HCS_SPEED_EST_SWITCH:OFF,
HO_ALGO_LDR_ALLOW_SHO_SWITCH:ON,
HO_ALGO_MBMS_FLC_SWITCH:OFF,
HO_ALGO_OVERLAY_SWITCH:OFF,
HO_INTER_FREQ_HARD_HO_SWITCH:OFF,
HO_INTER_RAT_CS_OUT_SWITCH:ON,
HO_INTER_RAT_PS_3G2G_CELLCHG_NACC_SWITCH:OFF,
HO_INTER_RAT_PS_3G2G_RELOCATION_SWITCH:OFF,
HO_INTER_RAT_PS_OUT_SWITCH:ON,
HO_INTER_RAT_RNC_SERVICE_HO_SWITCH:OFF,
HO_INTRA_FREQ_DETSET_INTO_ACTSET_SWITCH:ON,
HO_INTRA_FREQ_DETSET_RPRT_SWITCH:ON,
HO_INTRA_FREQ_HARD_HO_SWITCH:ON,
HO_INTRA_FREQ_RPRT_1J_SWITCH:OFF,
HO_INTRA_FREQ_SOFT_HO_SWITCH:ON,
HO_MC_MEAS_BEYOND_UE_CAP_SWITCH:OFF,
HO_MC_NCELL_COMBINE_SWITCH:ON,
HO_MC_SIGNAL_IUR_INTRA_SWITCH:OFF,
HO_MC_SIGNAL_SWITCH:OFF,
HO_MC_SNA_RESTRICTION_SWITCH:OFF,HO_LTE_PS_OUT_SWIT
CH:OFF,HO_LTE_SERVICE_PS_OUT_SWITCH:OFF,HO_H2G_SRVCC
_SWITCH:OFF RNC
SRNSR_DSCR_IUR_RESRCE_SWITCH:OFF,
SRNSR_DSCR_LOC_SEPRAT_SWITCH:ON,
SRNSR_DSCR_PROPG_DELAY_SWITCH:OFF,
SRNSR_DSCR_SEPRAT_DUR_SWITCH:ON RNC
CMCF_DL_HLS_SWITCH:ON, CMCF_UL_HLS_SWITCH:ON,
CMCF_UL_PRECFG_TOLERANCE_SWITCH:OFF,
CMCF_WITHOUT_UE_CAP_REPORT_SWITCH:OFF RNC
RESERVED_SWITCH_0_BIT1:OFF,
RESERVED_SWITCH_0_BIT32:OFF RNC
RESERVED_SWITCH_1_BIT1:ON, RESERVED_SWITCH_1_BIT2:ON,
RESERVED_SWITCH_1_BIT11:ON,
RESERVED_SWITCH_1_BIT32:ON RNC
0 RNC
4294967295 RNC
0 RNC
255 RNC
CMP_RELOCIN_IUUPVER_NOTCHG_SWITCH:OFF,
CMP_IUBR_DM_RTT_ALTERNATIVE_FMT_SWITCH:OFF,
CMP_IUR_CMCF_SWITCH:OFF,CMP_STTD_RL_ADD_SWITCH:OFF,
CMP_STTD_ASU_SWITCH:OFF,
CMP_RAB_DRD_ROLLBACK_PUNISH_SWITCH:OFF,
CMP_WBAMR_SUBFLOW_SWITCH:OFF,
CMP_IUR_CELLCAP_BITMAP_TRANSFORM_SWITCH:OFF,
CMP_MOCN_PLMN_SEL_SWITCH:OFF,
CMP_LOSSLESS_RELOC_RLCPDUSIZECHG_SWITCH:OFF,
CMP_CS_FIXED_RATE_WHEN_PS_EXIST_SWITCH:OFF RNC
PERFENH_AMR_SPEC_BR_SWITCH:ON,
PERFENH_AMR_TMPLT_SWITCH:ON,
PERFENH_SRB_TMPLT_SWITCH:ON,
PERFENH_OLPC_TMPLT_SWITCH:ON,
PERFENH_AMR_SP_TMPLT_SWITCH:ON,
PERFENH_INTRAFREQ_MC_TMPLT_SWITCH:ON,
PERFENH_INTERRAT_PENALTY_50_SWITCH:ON,
PERFENH_SRB_OVER_HSUPA_TTI10_SWITCH:OFF,
PERFENH_HSUPA_TTI2_ENHANCE_SWITCH:OFF,
PERFENH_UU_P2D_CUC_OPT_SWITCH:OFF,
PERFENH_RL_RECFG_SIR_CONSIDER_SWITCH:OFF
PERFENH_RRC_REDIR_PROTECT_SWITCH:OFF RNC
RESERVED_SWITCH_1_BIT32:OFF
RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
90 RNC
None Cell
None Physical channel
None RNC
110 RNC
90 RNC
80 RNC
80 RNC
90 RNC
50 RNC
5 RNC
100 RNC
10 RNC
150 RNC
None RNC
None RNC
None RNC
None RNC
D64 RNC
D64 RNC
D64 RNC
RATE_UP_AND_DOWN_ON_DCH RNC
RATE_UP_AND_DOWN_ON_EDCH RNC
10 Cell
20 Cell
3_Rates RNC
3_Rates RNC
HAND_APPOINT RNC
D128 RNC
3_Rates RNC
3_Rates RNC
HAND_APPOINT RNC
D128 RNC
4 RNC
60 RNC
30 RNC
D64 Cell
D64 Cell
100 RNC
D11480 RNC
30 None
None None
None None
None None
None None
None None
None None
None RNC
1 RNC
1 RNC
1 RNC
None RNC
None RNC
None RNC
None RNC
20 RNC
150 RNC
150 RNC
200 RNC
200 RNC
ON RNC
200 RNC
ON RNC
ON RNC
OFF RNC
20 RNC
1 RNC
ON RNC
6 RNC
5 RNC
1 RNC
5 RNC
TPE_DOWNLINK_SWITCH:OFF,TPE_UPLINK_SWITCH:OFF RNC
2 RNC
10 RNC
0 RNC
6 RNC
OFF RNC
ON RNC
Qos RNC
0 RNC
0 RNC
100 RNC
10 RNC
1 RNC
6 RNC
0 RNC
60 RNC
30 RNC
10 RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
50 RNC
RsvdSwitch1_Bit1:OFF, RsvdSwitch1_Bit2:OFF, RsvdSwitch1_Bit3:OFF,
RsvdSwitch1_Bit10:OFF, RsvdSwitch1_Bit11:OFF,
RsvdSwitch1_Bit32:OFF RNC
RsvdSwitch2_Bit32:OFF RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
0 RNC
2 RNC
OFF RNC
OFF RNC
OFF RNC
UserNumber RNC
Only_To_Inter_Frequency RNC
10 RNC
10 RNC
35 RNC
100 RNC
30 RNC
OFF RNC
7 RNC
SF8 RNC
13 RNC
DependOnNCell RNC
None RNC
None RNC
None RNC
ON RNC
10 RNC
25 RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
10 RNC
10 RNC
25 RNC
17 RNC
15 RNC
25 RNC
20 RNC
15 RNC
11 RNC
100 RNC
TEN_MSEC RNC
500 RNC
None RNC
100 RNC
TEN_MSEC RNC
500 RNC
None RNC
ON RNC
1 RNC
1 RNC
2 RNC
AC0-1&AC1-1&AC2-1&AC3-1&AC4-1&AC5-1&AC6-1&AC7-1&AC8-
1&AC9-1 RNC
100 RNC
10 RNC
60 RNC
20 RNC
10 RNC
5 RNC
5 RNC
None RNC
None RNC
ON RNC
None RNC
D2 RNC
None RNC
None RNC
D1 RNC
D1 RNC
ON RNC
D5 RNC
D4 RNC
If EDCHTTITYPE=EDCH_10MS, then it's D4;
If EDCHTTITYPE=EDCH_2MS, then it's D8; RNC
1 RNC
D2 RNC
D5 RNC
D20 RNC
D5 RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
Middle RNC
RATE_8KBPS: not selected
RATE_128KBPS: selected
RATE_11480KBPS: not selected RNC
ON None
Copper None
160 None
10 None
10 None
160 None
10 None
10 None
160 None
10 None
10 None
3 None
3 None
4 None
4 None
12 None
28 None
56 None
83 None
RTWP None
None Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
None Cell
8 Cell
15 Cell
15 Cell
None Cell
None Cell
TTI_10MS Cell
None Cell
None Cell
-20 Cell
20 Cell
2 Cell
8 Cell
0 Cell
0 Cell
8 Cell
D128 Cell
D32 Cell
374 Cell
None Cell
None Cell
None Cell
OFF Cell
None RNC
None RNC
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
GSM900_DCS1800_BAND_USED Cell
None Cell
NOT_USED Cell
0 Cell
20 Cell
NC0 Cell
0 Cell
0 Cell
0 Cell
None RNC
None Cell
SINGLE_HOST Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None RNC
None Cell
None Cell
None Cell
None Cell
None Cell
0 Cell
None Cell
0 Cell
None Cell
0 Cell
None Cell
0 Cell
None Cell
NOT_USED Cell
0 Cell
20 Cell
0 Cell
STTD_not_Supported Cell
CP1_not_Supported Cell
OFFSET1 Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
NOT_FORBIDDEN Cell
Mode0 Cell
0 Cell
None Cell
0 Cell
0 Cell
None Cell
None Cell
230 Transport channel
10 Cell
D15 Transport channel
D14 Transport channel
1 Transport channel
CONVOLUTIONAL Transport channel
D1/2 Transport channel
None RNC
None RNC
CONVERSATIONAL:7; STREAMING:8; INTERACTIVE:64;
BACKGROUND:64 RNC
None Cell
None Transport channel

Configured to 1 when "Number of TFs" is 1;
Configured to 0 when "Number of TFs" is 2 or 3 Transport channel
1 Transport channel
2 Transport channel
None Cell

12 RNC
-30 RNC
-200 RNC
-22 RNC
ALGORITHM1 RNC
1 RNC
STEPSIZE_1DB RNC
SINGLE_TPC RNC
ON RNC
11 RNC
6 RNC
D64 RNC
D64 RNC
D384 RNC
D384 RNC
D16 RNC
D64 RNC
NON-SCHEDULED RNC
D50 RNC
D50 RNC
D100 RNC
D100 RNC
D256 RNC
D128 RNC
OFF RNC
D32 RNC
EDCH_TTI_10ms RNC
D384 RNC
None RNC
41 RNC
5000 Cell
502 RNC
302 RNC
42 RNC
42 RNC
MIMO RNC
D32 RNC
SRB_OVER_HSDPA:ON, SRB_OVER_HSUPA:ON, TTI_2MS:ON,
MIMO:ON, 64QAM:ON, DL_L2_ENHANCE, DTX_DRX:ON,
HSSCCH_LESS_OPERATION:ON, MIMO_64QAM:OFF,
DC_HSDPA:OFF, UL_L2_ENHANCE:OFF, UL_16QAM:OFF,
EDPCCH_BOOSTING:OFF, DCMIMO_HSDPA:OFF RNC
SLOT_FORMAT_1 RNC
EDCH_TTI_10ms RNC
5 RNC
5 RNC
SCHEDULED RNC
SCHEDULED RNC
DC_HSDPA RNC
3640 RNC
1 RAB
NOT_TRIGGER RAB
NOT_PRE_EMPTABLE RAB
NOT_ALLOWED RAB
5 RAB
EDCH_TTI_2ms RAB
100 RNC
60 RNC
302 RNC
42 RNC
NON-SCHEDULED RNC
80 RNC
4 RNC
DCH RNC
DCH RNC
HSPA RNC
DCH RNC
DCH RNC
0 RNC
D8 RNC
D8 RNC
D64 RNC
D64 RNC
D256 RNC
D608 RNC
None BSC6900
None BSC6900
None None
None None
None None
20000 RNC
3 RNC
ON RNC
ON RNC
ON RNC
RsvdBit1:OFF, RsvdBit2:OFF, RsvdBit3:OFF, RsvdBit4:OFF,

RsvdBit29:OFF, RsvdBit30:OFF, RsvdBit31:OFF, RsvdBit32:OFF RNC
0 RNC
0 RNC
0 RNC
180 Cell
15 Cell
60 Cell
240 Cell
3 Cell
10 Cell
MAY RNC
0 RNC
COEXIST_MEAS_THD_CHOICE_INTERFREQ Cell
3 RNC
30 RNC
PO_24/15 Cell
PO_24/15 Cell
1 Cell
1 Cell
D2 Cell
D2 Cell
D8 Cell
D2 Cell
D4 Cell
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
D2000 RNC
3 RNC
6 RNC
D1 RNC
None Cell
None Cell
430 Cell

346 Cell
313 Cell
-7 Cell
-130 Cell
None None
None Cell
None RNC
None Cell
None None
None Cell
None None
None None
None None
NOT_RESERVED Cell
NOT_RESERVED Cell
D1280 Cell
None None
None RNC
None RNC
None None
None None
None RNC
None RNC
None RNC
None None
None None
None None
None Cell
None RNC
None None
None None
None RNC
None None
None None
None RNC
None None
None None
None RNC
None None
None None
None RNC
None None
None None
None None
None None
QPSK None
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None Cell
None Cell
None RNC
None RNC
None RNC
None RNC
D4;
D500 Cell
4 Cell
4 Cell
4 Cell
0 Cell
0 Cell
D0 Cell
D320 Cell
D1280 Cell
0 Cell
-14 Cell
-12 Cell
-14 Cell
-14 Cell
-12 Cell
-12 Cell
-95 Cell
-92 Cell
-95 Cell
-95 Cell
-92 Cell
-92 Cell
-12 Cell
-12 Cell
-12 Cell
-92 Cell
-92 Cell
-92 Cell
-12 Cell
-12 Cell
-12 Cell
-92 Cell
-92 Cell
-92 Cell
60 Cell
1 Cell
4 Cell
0 Cell
D4;
6 Cell
D640 Cell
-16 RNC
60 Cell
4 Cell
1 Cell
None RNC
None Cell
None RNC
None Cell
0 Cell
1 Cell
0 Cell
0 Cell
0 Cell
0 Cell
0 Cell
D0 Cell
D3 Cell
D2 Cell
2 Cell
0 Cell
-92 Cell
0 Cell
None Cell
-18 Cell
0 Cell
0 Cell
0 Cell
0 Cell
-24 Cell
-58 Cell
D3 Cell
AUTO Cell
D3 Cell
0 Cell
D1000 Cell
4 Cell
4 Cell
4 Cell
0 Cell
D320 Cell
D1280 Cell
D0 Cell
0 Cell
0 Cell
REQUIRED Cell
-14 Cell
-12 Cell
-15 Cell
-15 Cell
-13 Cell
-13 Cell
-100 Cell
-97 Cell
-110 Cell
-110 Cell
-107 Cell
-107 Cell
16 Cell
16 Cell
16 Cell
-12 Cell
-13 Cell
-13 Cell
-97 Cell
-107 Cell
-107 Cell
60 Cell
0 Cell
0 Cell
1 Cell
4 Cell
3 Cell
30 Cell
D3 Cell
0 Cell
D640 Cell
REQUIRED Cell
21 Cell
21 Cell
16 Cell
60 Cell
OFF RNC
ON RNC
80 Cell
60 Cell
4 Cell
1 Cell
3 Cell
30 Cell
D3 RNC
CPICH_EC/NO Cell
D16 Cell
D4000 Cell
D16 Cell
D4000 Cell
D64 Cell
D1000 Cell
6 Cell
6 Cell
6 Cell
12 Cell
12 Cell
12 Cell
-24 Cell
-115 Cell
0 Cell
0 Cell
8 Cell
8 Cell
8 Cell
8 Cell
0 Cell
D320 Cell
D640 Cell
D640 Cell
D640 Cell
D640 Cell
D640 Cell
60 RNC
3 RNC
2 RNC
30 RNC
-24 Cell
3 Cell
-115 Cell
D250 RNC
D2 RNC
None RNC
None Cell
None RNC
None Cell
0 Cell
AFFECT Cell
AFFECT Cell
1 Cell
0 Cell
0 Cell
0 Cell
0 Cell
0 Cell
D0 Cell
D3 Cell
D2 Cell
0 Cell
None Cell
1 Cell
None NodeB
None NodeB
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None BSC6900
None BSC6900
None RNC
None RNC
None BSC6900
None BSC6900
none None
None RNC
none BSC6900
none BSC6900
none None
None RNC
None RNC
2 RNC
30000 RNC
120000 RNC
20000 RNC
20000 RNC
60000 RNC
ON RNC
D6 RNC
60 RNC
200 RNC
60 RNC
100 RNC
60 RNC
100 RNC
60 RNC
100 RNC
60 RNC
100 RNC
60 RNC
100 RNC
40 RNC
200 RNC
40 RNC
200 RNC
40 RNC
200 RNC
SPU_KPI_AUTOCURE_SWITCH:OFF RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
IUBLDR RNC
CREDITLDR RNC
CODELDR RNC
UULDR RNC
NODEB_CREDIT_LDR_SWITCH:disabled.
LCG_CREDIT_LDR_SWITCH:disabled.
LC_CREDIT_LDR_SWITCH:disabled. RNC
ON RNC
1800 RNC
1800 RNC
10 RNC
3000 RNC
11 RNC
1800 RNC
D6 RNC
TEN_MSEC RNC
20 RNC
None RNC
D6 RNC
TEN_MSEC RNC
20 RNC
None RNC
150 RNC
32 RNC
32 RNC
5 RNC
5 RNC
5 RNC
5 RNC
5 RNC
5 RNC
TEN_MSEC RNC
100 RNC
None RNC
5 RNC
TEN_MSEC RNC
100 RNC
None RNC
5 RNC
3 RNC
D1 RNC
TEN_MSEC RNC
20 RNC
None RNC
100 RNC
D1 RNC
TEN_MSEC RNC
20 RNC
None RNC
100 RNC
TEN_MSEC RNC
100 RNC
None RNC
5 RNC
32 RNC
None NodeB
None NodeB
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
NotSupport Cell
None Cell
None RNC
None Cell
None Cell
2 None
None MBMS Service
None MBMS Service
None MBMS Service
None RNC
None RNC
None RNC
80 Cell
50 Cell
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
0 Physical channel
ON RNC
OFF RNC
OFF RNC
OFF RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
0 None
50 None
RRC_RAB None
7 RNC
3 RNC
1 RNC
ON Cell
10 Cell
D3000 RNC
-92 Cell
-12 Cell
10 Cell
6 Cell
D3000 Cell
-92 Cell
-12 Cell
OFF RNC
None None
-30 RNC
None RNC
None RNC
0 RNC
None Board
None BSC6900
When the "PROTOCOLTYPE" parameter is set to "ICMP", the

"AGINGTIMER" parameter should be set to 20s. When the
"PROTOCOLTYPE" parameter is set to "FTP", the "AGINGTIMER"
parameter should be set to 600s. When the "PROTOCOLTYPE"
parameter is set to "MSN", the "AGINGTIMER" parameter should be set
to 240s. When the "PROTOCOLTYPE" parameter is set to "SMTP", the
"AGINGTIMER" parameter should be set to 240s. When the
"PROTOCOLTYPE" parameter is set to "RTSP", the "AGINGTIMER"
parameter should be set to 120s. BSC6900
None BSC6900
None BSC6900
None None
None None
None None
None None
None BSC6900
None BSC6900
None BSC6900
RELIABILITY_CELL_SELFCURE_SWITCH:ON
CELL_SIB_NOT_UPD_NCELL_CHG_SWITCH:OFF RNC
PERFENH_R99_BRDCSTHSPA_SWITCH:OFF RNC
RESERVED_SWITCH_1_BIT32:OFF
RNC
0 RNC
0 RNC
0 RNC
0 RNC
None NodeB
None NodeB
None NodeB
None RNC
None Subsystem
None Subsystem
OFF Subsystem
OFF Subsystem
OFF Subsystem
None NodeB
None NodeB
None SAAL link
None SCTP link
SAAL NodeB
None NodeB
None NodeB
None None
None BSC6900
None UNI link
ON UNI link
None UNI link
0 UNI link
None None
None None
None NodeB
None NodeB
None Subsystem
None Subsystem
None Subsystem
ATM circuit transmission NodeB
None NodeB
10 NodeB
0 NodeB
R9 NodeB
SHARE NodeB
ON NodeB
SingleHost NodeB
None RNC
None NodeB
DEDICATED NodeB
None RNC
None NodeB
None NodeB
None NodeB
3840 NodeB
3840 NodeB
MBR NodeB
None NodeB
0 NodeB
0 NodeB
None BSC6900
None BSC6900
Disable BSC6900
None BSC6900
None NodeB
None BSC6900
None BSC6900
None NodeB
None IP route
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None NodeB
BERateRed NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
1 NodeB
1 NodeB
3 NodeB
1 NodeB
3 NodeB
1 NodeB
BERateRed NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
NoAct NodeB
1 NodeB
1 NodeB
3 NodeB
1 NodeB
3 NodeB
1 NodeB
1 NodeB
1 NodeB
SF8 NodeB
SF8 NodeB
2SF4 NodeB
None NodeB
None NodeB
None NodeB
1 NodeB
1 NodeB
None RNC
None Cell
None Cell
None RNC
None RNC
None RNC
None RNC
CS_SHO_SWITCH:OFF, HSPA_SHO_SWITCH:OFF,
NON_HSPA_SHO_SWITCH:OFF RNC
None RNC
None RNC
1 RNC
None RNC
None RNC
20 SCCP
NO RNC
None RNC
None RNC
CORRM_SRNSR_PSBE_RELOC RNC
OFF RNC
OFF RNC
OFF RNC
OFF RNC
RNC_NODE_REDUNDANCY_COMPATIBLE_SWITCH:OFF RNC
None RNC
None RNC
OFF RNC
None RNC
None RNC
None RNC
None RNC
OFF RNC
NOT_PERMIT_OFFLOAD RNC
80 RNC
OFF RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
SUPP_NONE RNC
SUPP_NONE RNC
3 RNC
None None
None None
None RNC
OFF RNC
OFF RNC
900 RNC
900 RNC
NO RNC
NO RNC
YES RNC
YES RNC
255 RNC
COMM_MOCN_NRI_GLOBAL_CONFIG_MODE_SWITCH:ON,
COMM_MIB_MULTI_PLMN_LIST_ALLOWED_SWITCH:ON RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
High RNC
High RNC
High RNC
High RNC
High RNC
Medium RNC
Medium RNC
Medium RNC
Medium RNC
Medium RNC
Low RNC
Low RNC
Low RNC
Low RNC
Low RNC
None RNC
None RNC
None RNC
None RNC
None RNC
D64 RNC
D64 RNC
None RNC
None RNC
None RNC
None RNC
0 RNC
None Cell
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
ARP RNC
NONE RNC
None Cell
3 Cell
None Cell
8 Cell
3 Cell
35 Cell
10 Cell
-20 Cell
None Cell
3 Cell

Configured to 1 when TFsNumber is 1;
Configured to 0 when TFsNumber is 2. Cell
1 Cell
None Cell
2 Cell
346 Cell
313 Cell
330 Cell
None Cell
346 Cell
313 Cell
OFF RNC
OFF RNC
10 RNC
1 RNC
None Cell
8 Cell
10 Cell
V36 Physical channel
0 Physical channel
None Cell
-7 Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
REHOSTRIGHNOW RNC
0 RNC
None RNC
None Cell
None Cell
SIGNATURE4, SIGNATURE5, SIGNATURE6, SIGNATURE7 Physical channel
SELECT ALL Physical channel
None Cell
None Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
ASC0 Cell
None Cell
4 Cell
None Cell
0 Cell
7 Cell
15 Physical channel
None Cell
4 Cell

SIGNATURE4, SIGNATURE5, SIGNATURE6, SIGNATURE7 Physical channel
SELECT ALL Physical channel

-20 Cell
20 Cell
2 Cell
BIT2 Physical channel
None Cell
4 Cell
0 Physical channel
1 Physical channel
2 Physical channel
3 Physical channel
None Cell
4 Cell

In signaling transmission mode, set PowerOffsetPpm to -3; in service
transmission mode, set PowerOffsetPpm to -2. Physical channel
15 Physical channel
None Cell
None Cell
-20 Cell
2 Cell
20 Cell
None Cell
0 Cell
20 RNC
20 RNC
20 RNC
20 RNC
20 RNC
20 RNC
20 RNC
20 RNC
360 RNC
20 RNC
20 RNC
4 RNC
10 RNC
ON RNC
2 RNC
320 RNC
2 RNC
ON RNC
ON RNC
3 RNC
3 RNC
3 RNC
3 RNC
D8 RNC
D1280 RNC
D1000 RNC
110 RNC
10 RNC
1 RNC
1 RNC
10 RNC
D8 RNC
D80 RNC
D250 RNC
D16 RNC
D0 RNC
D64 RNC
D0 RNC
OFF RNC
YES RNC
NO RNC
NO RNC
None RNC
None RNC
None RNC
3000 RNC
RateDegrade RNC
None RNC
None RNC
SINGLE RNC
YES RNC
NO RNC
NO RNC
3000 RNC
NO RNC
NO RNC
NO RNC
3000 RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
NO RNC
YES RNC
YES RNC
NO RNC
20 RNC
5 Cell
20 Cell
20 Cell
CPICH_RSCP Cell
D320 Cell
D320 Cell
D320 Cell
D320 Cell
D240 Cell
D640 Cell
D640 Cell
D240 Cell
D640 Cell
D2560 Cell
D1280 Cell
D1280 Cell
D240 Cell
D19 Cell
D1 Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
64 Cell
TEN_MSEC Cell
480 Cell
None Cell
OFF RNC
OFF RNC
ON RNC
OFF RNC
5 RNC
50 RNC
5 RNC
ON RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None Cell
4 Cell
1 Cell
1 Cell
0 Cell
0 Cell
8 Cell
None Cell
1 Cell
1 Transport channel
2 Transport channel
5000 RNC
3000 RNC
500 RNC
10 RNC
100 RNC
49 RNC
21 RNC
None RNC
None Cell
0 RNC
AMR:50; Other:0 RNC
DependOnNCell RNC
None RNC
None RNC
None RNC
None Cell
None Cell
None Cell
None Cell
None RNC
None RNC
None RNC
None RNC
None RNC
None None
None None
None None
OFF RNC
OFF RNC
ENGLISH RNC
300 RNC
0 RNC
OFF RNC
20 RNC
180 RNC
PTM RNC
D16 RNC
70 RNC
3 RNC
4 RNC
3 RNC
2 RNC
6 RNC
10 RNC
OFF RNC
ON RNC
ON RNC
D16 RNC
0 RNC
None RNC
1 RNC
5 RNC
2 RNC
IUCS_IUPS RNC
0 RNC
None RNC
None Cell
None Cell
None RNC
None RNC
None None
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
PTM RNC
4 RNC
3 RNC
None RNC
None RNC
None RNC
ON RNC
None RNC
None RNC
1800 RNC
1800 RNC
10 RNC
3000 RNC
11 RNC
1800 RNC
D6 RNC
TEN_MSEC RNC
20 RNC
None RNC
D6 RNC
TEN_MSEC RNC
20 RNC
None RNC
150 RNC
32 RNC
32 RNC
5 RNC
5 RNC
5 RNC
5 RNC
5 RNC
5 RNC
TEN_MSEC RNC
100 RNC
None RNC
5 RNC
TEN_MSEC RNC
100 RNC
None RNC
5 RNC
3 RNC
D1 RNC
TEN_MSEC RNC
20 RNC
None RNC
100 RNC
D1 RNC
TEN_MSEC RNC
20 RNC
None RNC
100 RNC
32 RNC
None Cell
None Cell
-20 Cell
50 Physical channel
None Cell
8 Cell
50 Physical channel
0 Physical channel
BIT4 Physical channel
EXISTS Physical channel
COMMON Cell
None Cell
None Cell
None RNC
None RNC
None RNC
None RNC
None Cell
All RNC
UE_BASED RNC
NODELIVERY RNC
None RNC
None RNC
16 RNC
UE_ASSISTED RNC
UE_ASSISTED RNC
OFF RNC
YES RNC
DRD RNC
R5_POSDATA_SWITCH RNC
OFF RNC
12 RNC
18 RNC
D160 RNC
D1280 RNC
-20 RNC
RNC_CENTRIC RNC
1000 RNC
AUTOMATIC RNC
None RNC
None Cell
None Cell
DEG Cell
MET Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
MIXED_ENVIRONMENT Cell
ACTIVE Cell
ACTIVE Cell
ACTIVE Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None Cell
None RNC
1 RNC
1 RNC
1 RNC
1 RNC
1 RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
313 None
200 None
60 RNC
400 RNC
5 RNC
60 RNC
30 RNC
NRT RNC
None Cell
1 Physical channel
5000 RNC
5000 RNC
350 RNC
5000 RNC
5000 RNC
1000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
11000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
5000 RNC
10000 RNC
45000 RNC
20000 RNC
5000 RNC
15000 RNC
5000 RNC
5000 RNC
10000 RNC
3000 RNC
10 RNC
5000 RNC
5000 RNC
5000 RNC
300 RNC
300 RNC
4 RNC
High RNC
High RNC
High RNC
High RNC
High RNC
Medium RNC
Medium RNC
Medium RNC
Medium RNC
Medium RNC
Low RNC
Low RNC
Low RNC
Low RNC
Low RNC
None RNC
None RNC
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
HO_TO_GSM_SHOULD_NOT_BE_PERFORM RAB
None RAB
SILENT RAB
None RAB
None RAB
None RNC
None RAB
D1024 RAB
None RAB
None RAB
D4000 RAB
D2560 RAB
D4000 RAB
2 RAB
16 RAB
2 RAB
16 RAB
2 RAB
16 RAB
None RNC
None RAB
D60 RAB
D16 RAB
D1 RAB
336 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
D100 RAB
1010 RAB
D1 RAB
336 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
D50 RAB
32 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
D1 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
When parameter TrchType is set to TRCH_EDCH_2MS, the
recommended value is 21; when parameter TrchType is set to
TRCH_EDCH_10MS, the recommended value is 12 RAB
When parameter TrchType is set to TRCH_EDCH_2MS, the
recommended value is 18; when parameter TrchType is set to
TRCH_EDCH_10MS, the recommended value is 9 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RNC
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RNC
None RNC
None RNC
None RNC
None RNC
500 RNC
280 RNC
512 RNC
None RNC
None RNC
None RNC
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
D32 RAB
1 RAB
NO_DISCARD RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
1 RAB
None RAB
None RAB
None RAB
1 RAB
1 RAB
None RAB
None RAB
None RAB
None RAB
None RAB
None RAB
0 RAB
0 RAB
5000 RAB
1000 RAB
1 RAB
160 RAB
2 RAB
1 RAB
80 RAB
14 RAB
1 RAB
50 RAB
None RAB
None RAB
None RAB
None RAB
None SRB
None SRB
None RAB
None RAB
None RAB
None SRB
None SRB
None SRB
None SRB
D1 SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
If TrchType is set to TRCH_EDCH_2MS, you are advised to set this
parameter to 21. If TrchType is set to TRCH_EDCH_10MS, you are
advised to set this parameter to 12. SRB
If TrchType is set to TRCH_EDCH_2MS, you are advised to set this
parameter to 18. If TrchType is set to TRCH_EDCH_10MS, you are
advised to set this parameter to 9. SRB
None SRB
None RAB
None RAB
None RAB
None RAB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
D32 SRB
D350 SRB
NO_DISCARD SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
D15 SRB
D32 SRB
0 SRB
None SRB
None SRB
None SRB
1 SRB
1 SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None SRB
None RNC
None RNC
30 Cell
None Cell
4 Cell
D0 Cell
36 Cell
20 Cell
UEA0-1; UEA1-1 RNC

9 RNC
D64 RNC
D5000 RNC
D1000 RNC
D5000 RNC
D16000 RNC
D1024 RNC
D0 RNC
D64 RNC
D5000 RNC
D1000 RNC
D1024 RNC
D0 RNC
D64 RNC
D5000 RNC
D16000 RNC
D1024 RNC
D0 RNC
30 RNC
8 RNC
2 RNC
4 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D1024 RNC
D0 RNC
D3k RNC
180 RNC
5 RNC
65535 RNC
5 RNC
180 RNC
5 RNC
5 RNC
180 RNC
5 RNC
5 RNC
180 RNC
5 RNC
180 RNC
UIA1-1 RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
D64 RNC
D64 RNC
None RNC
None RNC
None RNC
0 RNC
D3.4 RNC
D3.4 RNC
D16 RNC
D16 RNC
D16 RNC
D16 RNC
90 RNC
5 RNC
100 RNC
5 RNC
0 RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
None RNC
ARP RNC
NONE RNC
None RNC
OFF None
ALGORITHM_OFF RNC
PRIORITY2-1&PRIORITY3-1&PRIORITY4-1&PRIORITY5-
1&PRIORITY6-1 RNC
None None
None None
None None
None SAAL link
None None
None None
None Adjacent node
None None
None None
60 None
None None
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
None BSC6900
Parameter Relationship
None
None
None
When the value of "RscMngMode" in "ADD UNODEB" of the resource corresponding NodeB is set to EXCLUSIVE, the AAL2 P
LGCPORT or RSCGRP
When the value of "CARRYT" in "ADD AAL2PATH" is set to UNI, IMA, FRAATM, NCOPT, or ATM LGCPORT, this parameter
When the value of "CARRYT" in "ADD AAL2PATH" is set to UNI, IMA, FRAATM, NCOPT, or ATM LGCPORT, this parameter
When the value of "CARRYT" in "ADD AAL2PATH" is set to UNI, this parameter is valid.
When the value of "CARRYT" in "ADD AAL2PATH" is set to IMA, this parameter is valid.
When the value of "CARRYT" in "ADD AAL2PATH" is set to FRAATM, this parameter is valid.
When the value of "CARRYT" in "ADD AAL2PATH" is set to NCOPT, this parameter is valid.
When the value of "CARRYT" in "ADD AAL2PATH" is set to ATM LGCPORT, this parameter is valid.
When the value of "CARRYT" in "ADD AAL2PATH" is set to UNI, IMA, FRAATM, or NCOPT, this parameter is valid.
None
When the value of "CARRYT" in "ADD AAL2PATH" is set to UNI, IMA, FRAATM, NCOPT, or ATMLOGICPORT, this paramete
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the value of "ITFT" in "ADD TRMMAP" is set to IUB, IUR, IUCS, this parameter is valid.
None
When "RSCMNGMODE" in "ADD RSCGRP" is set to EXCLUSIVE, this parameter is valid.
The TRMMAP index is configured by setting the value of "TMI" in "ADD TRMMAP".
The factor table index is configured by setting the value of "FTI" in "ADD TRMFACTOR".
The load EQ table index is configured by setting the value of "LEI" in "ADD LOADEQ".
None
None
None
When the value of "NODET" in "ADD ADJNODE" is set to IUB, this parameter is valid.
When the value of "NODET" in "ADD ADJNODE" is set to IUPS, this parameter is valid.
When the value of "NODET" in "ADD ADJNODE" is set to IUB, IUR, IUCS, or IUPS, this parameter is valid.
When the value of "NODET" in "ADD ADJNODE" is set to IUR, IUCS, or NNI_AAL2SWITCH, or the value of "NODET" in "ADD
"SGSNFLG" in "ADD ADJNODE" is set to YES, this parameter is valid.
When the value of "NODET" in "ADD ADJNODE" is set to IUB, IUR, or IUCS, and the value of "TRANST" in "ADD ADJNODE"
parameter is valid.
When the value of "IsROOTNODE" in "ADD ADJNODE" is set to NO, this parameter is valid.
None
When the value of "NODET" in "ADD ADJNODE" is set to IUB, and the value of "IsROOTNODE" in "ADD ADJNODE" is set to
"ADD ADJNODE" is set to UNI_AAL2SWITCH, this parameter is valid.
None
When the value of "NODET" in "ADD ADJNODE" is set to IUB, IUR, or IUCS, and the value of "IsROOTNODE" in "ADD ADJN
of "NODET" in "ADD ADJNODE" is set to UNI_AAL2SWITCH or NNI_AAL2SWITCH, this parameter is valid.
None
None
None
None
None
None
If you set "Switch of stat blinking alarm" to "ENABLE", you need to set "Alarm switch of blinking filter" to "ENABLE".
If you set "Switch of stat blinking alarm" to "ENABLE", you need to set "Alarm switch of blinking filter" to "ENABLE".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when SW is ON in SET ASWPARA.
This parameter is valid when SW is OFF in SET ASWPARA.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The TRM load threshold index is configured by setting the value of "TRMLOADTHINDEX" in "ADD TRMLOADTH". The TRM lo
meet the following conditions: forward congestion recovery threshold < logical port bandwidth, backward congestion recovery
bandwidth.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when PKPEnableSta is ENABLE in SET CERTFILE.
None
This parameter is valid when CRLEnableSta is ENABLE in SET CERTFILE.
None
This parameter is valid when CCAEnableSta is ENABLE in SET CERTFILE.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If port 0 or port 4 of the FG2a board is set to the GE port, the port number can only be 0 or 4. Otherwise, the port number rang
set to the GE port, ports 1-3 are unavailable. If port 4 is set to the GE port, ports 5-7 are unavailable.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of "Upper Limit of Signal Output of External Analog 1" is V;
Analog 1" is set to CURRENT, the unit of "Upper Limit of Signal Output of External Analog 1" is A.
If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of "Lower Limit of Signal Output of External Analog 1" is V;
Analog 1" is set to CURRENT, the unit of "Lower Limit of Signal Output of External Analog 1" is A.
If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of "Upper Limit of Measurement Range of External Analog 1
External Analog 1" is set to CURRENT, the unit of "Upper Limit of Measurement Range of External Analog 1" is A.
If "Sensor Type of External Analog 1" is set to VOLTAGE, the unit of "Lower Limit of Measurement Range of External Analog 1
External Analog 1" is set to CURRENT, the unit of "Lower Limit of Measurement Range of External Analog 1" is A.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The number of CPU usage sampling times is at least twice the size of "Fast judgement window".
None
None
The value of this parameter must be larger than
"PRINTRTHD".
The value of this parameter must be smaller than
"PRINTCTHD".
"TRACERTHD".
"TRACECTHD".
"PMRTHD".
"PMCTHD".
"RESAUDITRTHD".
"RESAUDITCTHD".
"SMPAGERTHD".
"SMPAGECTHD".
"SLPAGERTHD".
"SLPAGECTHD".
"CPAGERTHD".
"CPAGECTHD".
"HANDOVERRTHD".
"HANDOVERCTHD".
"IURULRTHD".
"IURULCTHD".
"IURDLRTHD".
"IURDLCTHD".
"CBSRTHD".
"CBSCTHD".
"LOGRTHD".
"LOGCTHD".
"CELLURARTHD".
"CELLURACTHD".
None
None
"ACRTHD".
"ACCTHD".
"IURGRTHD".
"IURGCTHD".
The following relationship must be satisfied:
"LPRISERVCTHD" > "LPRISERVRTHD"; "HPRISERVCTHD" >
"NPRISERVCTHD" > "LPRISERVCTHD".
"LPRISERVCTHD" > "LPRISERVRTHD"; "HPRISERVCTHD" >
"NPRISERVCTHD" > "NPRISERVRTHD"; "HPRISERVCTHD" >
"NPRISERVCTHD" > "NPRISERVRTHD"; "HPRISERVCTHD" >
"HPRISERVCTHD" > "HPRISERVRTHD"; "HPRISERVCTHD" >
"HPRISERVCTHD" > "HPRISERVRTHD"; "HPRISERVCTHD" >
"MRRTHD".
The value of this parameter must be smaller than "MRCTHD".
None
The number of CPU usage sampling times is at least twice the size of "Fast judgement window".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when DFTPORTSWT is CUSTOMPORT in SET FTPSSRV.
This parameter is valid when DFTPORTSWT is CUSTOMPORT in SET FTPSSRV.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when RESTYPE is IU in SET INFBRDRESCFG.
This parameter is valid when RESTYPE is IUB in SET INFBRDRESCFG.

This parameter is valid when RESTYPE is CELL_KPI, IP_PATH, GB, GTPU, AL, SIGNALING_PLANE_LOOP or USER_PLAN
INFBRDRESCFG.
This parameter is valid when RESTYPE is IUB or CELL_KPI in SET INFBRDRESCFG.
This parameter is valid when RESTYPE is AL or GTPU in SET INFBRDRESCFG.
This parameter is valid when RESTYPE is IUB, USER_PLANE_LOOP, IU, AL, GTPU or CELL_KPI in SET INFBRDRESCFG.
This parameter is valid when RESTYPE is IUB, USER_PLANE_LOOP, IU or CELL_KPI in SET INFBRDRESCFG.
None
None
This parameter is valid when RESTYPE is SIGNALING_PLANE_LOOP in SET INFBRDRESCFG.
None
None
None
None
The value of this parameter must be greater than that of "Invalid Packet Alarm Clearance Threshold".
The value of this parameter must be less than that of "Invalid Packet Alarm Threshold".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The dynamic bandwidth switch is turned only when the IPPM function is activated through "ACT IPPM".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This index can correspond with any threshold (maximum value of 80) in the six queues. The following condition must be met: t
port bandwidth < 4294967295(0xFFFFFFFF).
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The "IPADDR" in "ADD IPPATH" can not be at one network segment with the peer IP address of SCTPLNK or IPPATH whose
address of FG2/GOU in this subrack;"IPADDR" and "PEERIPADDR" in "ADD IPPATH" must be at one network segment;
("IPADDR","PEERIPADDR","PEERMASK" in "ADD IPPATH") conflicts with other IPPATH whose type is IUPS.
"IPADDR" and "PEERIPADDR" in "ADD IPPATH" must be at one network segment;("IPADDR","PEERIPADDR","PEERMASK"

other IPPATH whose type is IUPS.
("IPADDR","PEERIPADDR","PEERMASK" in "ADD IPPATH") conflicts with other IPPATH whose type is IUPS.
None
None
None
When the value of "CARRYFLAG" in "ADD IPPATH" is set to IP LGCPORT, this parameter is valid.
When the value of "CARRYFLAG" in "ADD IPPATH" is set to IP LGCPORT, this parameter is valid.
None
None
None
None
None
When the value of "PATHCHK" in "ADD IPPATH" is set to ENABLED, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1.The parameter is used in command "ADD ADJMAP" as loadeq table index for gold,silver,and bronze users.
2.When TRANST of ADJNODE is dual stack or Hybrid IP,loadeq can be added.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when FRMFLAG is ENABLE in SET LOGCFG.
This parameter is valid when FILTERKEY is TASKID in SET LOGCFG.
This parameter is valid when FILTERKEY is CMDCODE in SET LOGCFG.

None
None
None
None
None
None
Negotiation with the peer network element is required.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the value of "SPDF" in "ADD N7DPC" is set to WNF, this parameter is valid.
When the value of "SPDF" in "ADD N7DPC" is set to DNF, this parameter is valid.
None
None
None
None
None
None
None
None
None
This parameter is valid when OBJTP is BOARD, PORT or DSP.
This parameter is valid when OBJTP is PORT.
This parameter is valid when OBJTP is DSP.

This parameter is valid when OBJTP is BOARD, PORT or DSP.
This parameter is valid when OBJTP is ALL or AIDST is ONEBYONE.
None
None
None
None
None
None
None
None
None
This parameter is valid when UG is Customs.
None
This parameter is valid when DATE is LIMIT.
This parameter is valid when DATE is LIMIT.
None
This parameter is valid when TIME is LIMIT.
This parameter is valid when TIME is LIMIT.
None
This parameter is valid when WEEK is LIMIT.
None
None
None
None
None
None
This parameter depends on network planning.
This parameter depends on network planning.
None
When the value of "SPDF" is set to WNF, this parameter is valid.
When the value of "SPDF" is set to DNF, this parameter is valid.
When the value of "SPCBITS" is set to BIT14 or BIT24, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The phb of the traffic's transmission path is determined like this: if the phb of this transmission path is QOS, use the traffic's ph
this transmission path is BE,AF11,AF12,AF13,AF21,AF22,AF23,AF31,AF32,AF33,AF41,AF42,AF43,EF, use the phb of transm
None
None
None
When the value of "PORTPROTYPE" in "ADD PORTFLOWCTRLPARA" is set to IP, this parameter should be set.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The ASCs are configured through "ADD UERACHASC".
None
None
None
None
None
When "ISFIRSTCLASSE" in "ADD RSCGRP" is set to NO, this parameter is valid.
When "ISFIRSTCLASSE" in "ADD RSCGRP" is set to YES, this parameter is valid.
When "RSCMNGMODE" in "ADD RSCGRP" is set to EXCLUSIVE, this parameter is valid.
When "GRPT" in "ADD RSCGRP" is set to IP, this parameter is valid.

When "GRPT" in "ADD RSCGRP" is set to ATM or "BWMODE" is set to FULL_DUPLEX, this parameter is valid;The sum of "T
RSCGRP" of upper class RSCGRP can not less than the "TxBw" and "AllBw" in "ADD RSCGRP"of lower class RSCGRP;The
upper class RSCGRP can not less than the "TxBw" in "ADD RSCGRP" of lower class RSCGRP, and the "RxBw" in "ADD RSC
can not less than the "RxBw" in "ADD RSCGRP" of lower class RSCGRP.
When "GRPT" in "ADD RSCGRP" is set to ATM or "BWMODE" is set to FULL_DUPLEX, this parameter is valid;The sum of "T
RSCGRP" of upper class RSCGRP can not less than the "TxBw" and "AllBw" in "ADD RSCGRP"of lower class RSCGRP;The
upper class RSCGRP can not less than the "TxBw" in "ADD RSCGRP" of lower class RSCGRP, and the "RxBw" in "ADD RSC
can not less than the "RxBw" in "ADD RSCGRP" of lower class RSCGRP.
When "BWMODE" in "ADD RSCGRP" is set to HALF_DUPLEX, this parameter is valid;if the "BWMODE" in "ADD RSCGRP" o
RSCGRP is set to HALF_DUPLEX, the "AllBw" in "ADD RSCGRP" of upper class RSCGRP can not less than the "AllBwE" in
RSCGRP;The "AllBw" in "ADD RSCGRP" of upper class RSCGRP can not less than the sum of "TxBw" and "RxBw" in "ADD R
RSCGRP.
None
None
None
None
None
When the value of "CARRYT" is set to IMA, UNI, FRAATM, NCOPT, or ATMLOGICPORT, this parameter is valid.
When the value of "CARRYT" is set to UNI, this parameter is valid.
When the value of "CARRYT" is set to IMA, this parameter is valid.
When the value of "CARRYT" is set to FRAATM, this parameter is valid.
When the value of "CARRYT" is set to NCOPT, this parameter is valid.
When the value of "CARRYT" is set to ATMLOGICPORT, this parameter is valid.
None
When the value of "SAALLNKT" is set to NNI, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the value of "MODE" in "ADD SCTPLNK" is set to Client, this parameter can be modified.
None
None
None
None
None
This parameter determines whether "LOGPORTSN" and "LOGPORTNO" in "ADD SCTPLNK" are valid.
When the value of "LOGPORTFLAG" in "ADD SCTPLNK" is set to ON, this parameter is valid.
When the value of "LOGPORTFLAG" in "ADD SCTPLNK" is set to ON, this parameter is valid.
The value to be set should be smaller than the value of "RTOMAX" in "ADD SCTPLNK".
The value to be set should be larger than the value of "RTOMIN" in "ADD SCTPLNK".
The value to be set should be larger than the value of "RTOMIN" in "ADD SCTPLNK" but smaller than the value of "RTOMAX"
None
None
None
None
The value to be set should be larger than the value of "MAXPATHRETR" in "ADD SCTPLNK".
The value to be set should be smaller than the value of "MAXASSOCRETR" in "ADD SCTPLNK".
None
None
None
None
None
None
None
None
None
None
None
None
None
The value to be set should be larger than the value of "MAXPATHRETR" in "ADD SCTPLNK".
The value to be set should be smaller than the value of "MAXASSOCRETR" in "ADD SCTPLNK".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when SWITCH is ON in SET SLFSLVSW.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when FREQ is not ONTIME in "ADD SUBTSK".
This parameter is valid when FREQ is not ONTIME in "ADD SUBTSK".

This parameter is valid when FREQ is MONTHLY_T or MONTHLY_C.
This parameter is valid when FREQ is WEEKLY_T or WEEKLY_C.
This parameter is valid when FREQ is DAILY_T, WEEKLY_T or MONTHLY_T in "ADD SUBTSK".
This parameter is valid when FREQ is DAILY_C, WEEKLY_C or MONTHLY_C in "ADD SUBTSK".
This parameter is valid when FREQ is ONTIME in "ADD SUBTSK".
None
None
This parameter is valid when FREQ is not ONTIME in "MOD SUBTSK".
This parameter is valid when FREQ is not ONTIME in "MOD SUBTSK".
This parameter is valid when FREQ is DAILY_T, WEEKLY_T or MONTHLY_T in "MOD SUBTSK".
This parameter is valid when FREQ is DAILY_C, WEEKLY_C or MONTHLY_C in "MOD SUBTSK".
This parameter is valid when FREQ is ONTIME in "MOD SUBTSK".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the value of "ITFT" in "ADD TRMMAP" is set to IUB, IUR or IUCS, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the value of "ITFT" in "ADD TRMMAP" is set to IUB, IUR or IUCS, this parameter is valid.
When the value of "ITFT" in "ADD TRMMAP" is set to IUB or IUR, this parameter is valid.
When the value of "ITFT" in "ADD TRMMAP" is set to IUB or IUR or IUPS, this parameter is valid.
When the value of "ITFT" in "ADD TRMMAP" is set to IUB or IUR or IUCS, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "TpenaltyHcsReselect" is not set to D0.
None
This paramter is valid only when "BlindHoFlag" is set to TRUE.
None
None
None
None
This parameter is valid only when "NPrioFlag" is set to TRUE.
None
None
None
None
None
None
None
None
None
This parameter is valid only when "AFSetObj" is set to NOPRIORITY.
This parameter is valid only when "AFSetObj" is set to NOPRIORITY.
This parameter is valid only when "AFSetObj" is set to GOLD, SILVER, or COPPER.
This parameter is valid only when "AFSetObj" is set to GGOLD, SILVER, or COPPER.
This parameter is valid only when "AFSetObj" is set to GOLD,SILVER, or COPPER.
None
None
None
None
None
None
None
None
None
None
None
"DlThdE1" <= "DlThdE2" < "DlThdF2" <= "DlThdF1".
"UlModeChangeTimerLen" <= "DlModeChangeTimerLen".

"GoldMaxMode" >= "SilverMaxMode" >= "CopperMaxMode".

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The value of this parameter must be smaller than "DlRateThreshold2".
The value of this parameter must be greater than "DlRateThreshold1" and smaller than "DlRateThreshold3".
The value of this parameter must be greater than "DlRateThreshold8".
None
The value of this parameter must be smaller than "UlRateThreshold2".
The value of this parameter must be greater than "UlRateThreshold1" and smaller than "UlRateThreshold3".
The value of this parameter must be greater than "UlRateThreshold8".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When "CARRYLNKT" is SAAL-SCTP, this parameter is valid.
None
When "STACKMODTYPE" is ATMTODUAL or IPTODUAL, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
When "UARFCNUplinkInd" is set to TRUE, this parameter need to manual configure;or else need to automatic configure with t
frequency.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This paramter is valid only when "TxDiversityInd" is set to TRUE.
This parameter is valid only when "CP1SupInd" is set to CP1_Supported.

This paramter is set to STTD only when "STTDSupInd" is set to STTD_Supported.
This paramter is set to CP1 only when "CP1SupInd" is set to CP1_Supported.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1. The value of this parameter must satisfy the following relationship:
"Min Transmit Power of PCPICH" <= "PCPICH Transmit Power" <="Max Transmit Power of PCPICH"
2. To modify the "PCPICH Transmit Power", the intra-frequency load balance algorithm of the cell should be disabled. You can
UCELLALGOSWITCH" to query the switch and use "MOD UCELLALGOSWITCH" to modify the switch.
None
None
None
None
None
None
None
None
None
None
None
"Min Transmit Power of PCPICH" <= "PCPICH Transmit Power" <= "Max Transmit Power of PCPICH"
None
The value of this parameter must satisfy the following relationship:

"Min Transmit Power of PCPICH" <= "Max Transmit Power of PCPICH".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "IdleCellBarred" is set to BARRED.
This parameter is valid only when "IdleCellBarred" is set to BARRED.

None
This parameter is valid only when "ConnCellBarred" is set to BARRED.
This parameter is valid only when "ConnCellBarred" is set to BARRED.
None
None
None
None
None
None
None
None
If the Downlink CAC algorithm switch select the equivalent user number algorithm,then Intra Frequency LDB Algorithm must b
PUC should not be adopted if cell's selection and reselection information has been configured but Inter-freq cell reselection thr
PUC should not be adopted if cell's inter-frequency measurement control information has been configured as not required.
Note:Inter-freq cell reselection threshold is set by"ADD UCELLSELRESEL".Inter-frequency measurement control information i
None
None
None
None
None
None
None
None
None
None
None
None

None
None
"UlNonCtrlThdForHo" > "UlNonCtrlThdForAMR";
"UlNonCtrlThdForAMR" > "UlNonCtrlThdForOther";
MAX("UlNonCtrlThdForHo", "UlNonCtrlThdForAMR", "UlNonCtrlThdForNonAMR", "UlNonCtrlThdForOther") > "UlLdrTrigThd" >
(For detailed information, refer to "ADD UCELLLDM").
"UlNonCtrlThdForHo" > "UlNonCtrlThdForNonAMR";
"UlNonCtrlThdForNonAMR" > "UlNonCtrlThdForOther";


"DlHOThd" > "DlConvAMRThd";
"DlConvAMRThd" > "DlOtherThd"

"DlHOThd" > "DlConvNonAMRThd";
"DlConvNonAMRThd" > "DlOtherThd"
"DlConvAMRThd" > "DlOtherThd";
"DlConvNonAMRThd" > "DlOtherThd";
"DlOtherThd" >= "DlLdrTrigThd"(See "ADD UCELLLDM")

"UlCellTotalThd" > "UlNonCtrlThdForHo" ;
"UlNonCtrlThdForHo" > "UlNonCtrlThdForAMR";
"UlNonCtrlThdForHo" > "UlNonCtrlThdForNonAMR";
"DlCellTotalThd" >= "DlHOThd" ;
"DlHOThd" > "DlConvAMRThd";
"DlHOThd" > "DlConvNonAMRThd"
"UlOlcTrigThd"(See "ADD UCELLLDM") >= "UlCellTotalThd";
"UlCellTotalThd" > "UlNonCtrlThdForHo"
"DlOlcTrigThd"(See "ADD UCELLLDM") >= "DlCellTotalThd";
"DlCellTotalThd" >= "DlHOThd"
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"MtchMaxPwr" >= "MtchRsvPwr".
"MtchMaxSf" >= "MtchRsvSf"
"MtchMaxPwr" >= "MtchRsvPwr"
"MtchMaxSf" >= "MtchRsvSf"
"UlHoCeResvSf" >= "UlLdrCreditSfResThd". The comparison between the sprea
number following the acronym "SF", for example, SF32>SF8.
(For detailed information, refer to "ADD UCELLLDR".)
"DlHoCeCodeResvSf" >= "DlLdrCreditSfResThd";
"DlHoCeCodeResvSf" >= "CellLdrSfResThd". The comparison between the spre
number following the acronym "SF", for example, SF32>SF8.
(For detailed information, refer to "ADD UCELLLDR")
"BgnEndTime" >"MBgnStartTime" .

"BgnEndTime" >"MBgnStartTime" .
"BgnAbnormalThd" >= "BgnUpdateThd"
"BgnAbnormalThd" >= "BgnUpdateThd"
None
None
None
None
None
None
None
None
None
Before configuring this parameter, you need to configure the information about the common traffic logical channel by running "
you need to set the CBS scheduling parameter of the cell by running "ADD UCELLCBSDRX".
None
When the value of "MsgInd" is set to ON, this parameter is valid. When "CBSwitch" is set to ON in "SET URNCCBPARA" and
broadcast can be performed in a specified cell. This parameter specifies the content of broadcast messages.
None
None
None
None
None
This parameter is available if the value of "BEQosPerform" in "SET UQOSACT" is YES.
None
None
None
None
None
None
If this parameter is set through both the "ADD UCELLDRD" and "SET UDRD" commands, the parameter set through the "ADD
This parameter is valid only when the "LdbDRDSwitchDCH" parameter is set to ON.
This parameter is valid only when the "LdbDRDSwitchHSDPA" parameter is set to ON.
This parameter is valid only when the "CodeBalancingDrdSwitch" parameter is set to ON.
This parameter is required only when the "ReDirUARFCNUplinkInd" parameter is set to TRUE.
The value range of this parameter depends on the setting of the "ReDirBandInd" parameter, as shown below:
BAND1
BAND2
Special UARFCNs: {12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287}
BAND3
BAND4
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
BandIndNotUsed
[0-16383]
BAND1
BAND2
Special UARFCNs: {412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687}
BAND3
BAND4
Special UARFCNs: {1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087}
BAND5
Special UARFCNs: {1007, 1012, 1032, 1037, 1062, 1087}
BAND6
BAND7
Special UARFCNs: {2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912}
BAND8
BAND9
BandIndNotUsed
[0-16383]
precedence over that set through the "SET UDRD" command.
If this parameter is set by running both the "ADD UCELLDRD" and "SET UDRD" commands, the parameter setting in the "ADD
effect.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When "RestrictionType" in "ADD UCELLDSACMANUALPARA" is RestrictionFixed, AcRestriction should be configured. When
UCELLDSACMANUALPARA" is RestrictionFlexible, AcRestriction should not be configured.
Only when "RestrictionType" in "ADD UCELLDSACMANUALPARA" is RestrictionFixed, this parameter should be configured.
None
None
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_1 or ON_2 or ON_3;
The value of this parameter must fulfill the following condition:
"First Cell Dynamic ShutDown Interval Start Time" < "First Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_1 or ON_2 or ON_3;
"First Cell Dynamic ShutDown Interval Start Time" < "First Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_2 or ON_3;
"Second Cell Dynamic ShutDown Interval Start Time" < "Second Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_2 or ON_3;
"Second Cell Dynamic ShutDown Interval Start Time" < "Second Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_3;
"Third Cell Dynamic ShutDown Interval Start Time" < "Third Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_3;
"Third Cell Dynamic ShutDown Interval Start Time" < "Third Cell Dynamic ShutDown Interval End Time".
This paramter is valid only when "Cell Dynamic ShutDown Switch" is set to ON_1 or ON_2 or ON_3.
This paramter is valid only when "Cell Dynamic ShutDown Type" is set to ConditionalShutDown or QosShutDown.
This parameter is valid only when "Cell Dynamic ShutDown Type" is set to QosShutDown.
None
None
None
None
None
None
None
None
None
This parameter must satisfy the following relationship: "CCCHMBR" >= "CCCHGBR"
This parameter must satisfy the following relationship: "CCCHMBR" >= "CCCHGBR"
This parameter must satisfy the following relationship: "SRBMBR" >= "SRBGBR"
This parameter must satisfy the following relationship: "SRBMBR" >= "SRBGBR"
This parameter must satisfy the following relationship: "CONVMBR" >= "CONVGBR"
This parameter must satisfy the following relationship: "CONVMBR" >= "CONVGBR"
This parameter must satisfy the following relationship: "STREAMMBR" >= "STREAMGBR"
This parameter must satisfy the following relationship: "STREAMMBR" >= "STREAMGBR"
This parameter must satisfy the following relationship: "INTERACTMBR" >= "INTERACTGBR"
This parameter must satisfy the following relationship: "INTERACTMBR" >= "INTERACTGBR"
This parameter must satisfy the following relationship: "BGMBR" >= "BGGBR"
This parameter must satisfy the following relationship: "BGMBR" >= "BGGBR"
This parameter must satisfy the following relationship: "IMSMBR" >= "IMSGBR"
This parameter must satisfy the following relationship: "IMSMBR" >= "IMSGBR"
None
None
None
None
None
None
None
None
None
None
If this parameter is set through both the "SET UFRCCHLTYPEPARA" and "ADD UCELLFRC" commands, the parameter set th
command prevails.
command prevails.
The code-resource-saving mode is applicable to narrowband AMR services only when this parameter is set to TRUE and the "
parameter is set to ON through the "SET UFRC" command.
command prevails.
If this parameter is set through both the "SET UFRC" and "ADD UCELLFRC" commands, the parameter set through the "ADD
None
This parameter should have been added through the "ADD URRCESTCAUSESIGCHTYPE"command.
None
None
None
None
When "UARFCNUplinkInd" is set to TRUE, this parameter need to manual configure;or else need to automatic configure with t
frequency.
None
The GPS frame timing information of the cell idendified by this parameter must have been configured through "ADD UCELLGP
None
None
None
This parameter is required when the "UseOfHcs" parameter is set to USED but not required when the "UseOfHcs" parameter i
This parameter is valid only when "UseOfHcs" is set to USED.
None
This parameter is valid when the HCS_SPD_EST_SWITCH is set to ON and "UseOfHcs" is set to USED in "ADD UCELLHCS
HO_ALGO_HCS_SPEED_EST_SWITCH in "HoSwitch" in "SET UCORRMALGOSWITCH".
The value of the parameter must satisfy the function below:

"NFastSpdEst"*"TSlowSpdEst" >= "NSlowSpdEst"*"TFastSpdEst".

None
The value of the parameter must meet the following condition:

"NFastSpdEst"*"TSlowSpdEst" >= "NSlowSpdEst"*"TFastSpdEst"

None
None
None
None
None
None
None
None
This paramter is valid only when "AllocCodeMode" is set to Manual.
This paramter is valid only when "AllocCodeMode" is set to Automatic and the value of this parameter must satisfy the followin
"HsPdschMaxCodeNum" >= "HsPdschMinCodeNum".
This paramter is valid only when "AllocCodeMode" is set to Automatic and the value of this parameter must satisfy the followin
"HsPdschMaxCodeNum" >= "HsPdschMinCodeNum".
None
None
None
None
None
This paramter is valid only when "CodeAdjForHsdpaSwitch" is set to ON.
None
None
None
None
None
None
When the value of "CQIFbCk" is not 0, half of the value of "CQIFbCk" must be greater than the value of "CQIReF".
When the value of "CQIFbCkforSHO" is not 0, half of the value of "CQIFbCkforSHO" must be greater than the value of "CQIRe
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "InterFreqReportMode" is set to PERIODICAL_REPORTING.
This parameter is valid when "InterFreqReportMode" is set to EVENT_TRIGGER.
None
None
None
None
None
The value of this parameter must be smaller than "InterFreqCsThd2FEcN0".
The value of this parameter must be larger than "InterFreqCsThd2DEcN0".

The value of this parameter must be smaller than "InterFreqR99PsThd2FEcN0".
The value of this parameter must be smaller than "InterFreqHThd2FEcN0".
The value of this parameter must be greater than "InterFreqR99PsThd2DEcN0".
The value of this parameter must be greater than "InterFreqHThd2DEcN0".
The value of this parameter must be smaller than "InterFreqCsThd2FRscp".
The value of this parameter must be greater than "InterFreqCsThd2DRscp".

The value of this parameter must be smaller than "InterFreqR99PsThd2FRscp".
The value of this parameter must be smaller than "InterFreqHThd2FRscp".
The value of this parameter must be greater than "InterFreqR99PsThd2DRscp".
The value of this parameter must be larger than "InterFreqHThd2DRscp".
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "InterFreqReportMode" is set to "EVENT_TRIGGER".
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "InterRatReportMode" is set to EVENT_TRIGGER.
None
None
This parameter is valid when "InterRatReportMode" is set to PERIODICAL_REPORTING.

None
None
None
None

None
The value of this parameter must be smaller than "InterRatCsThd2FEcN0".
The value of this parameter must be larger than "InterRatCsThd2DEcN0".
The value of this parameter must be smaller than "InterRatR99PsThd2FEcN0".

The value of this parameter must be smaller than "InterRatHThd2FEcN0".
The value of this parameter must be larger than "InterRatR99PsThd2DEcN0".
The value of this parameter must be larger than "InterRatHThd2DEcN0".
The value of this parameter must be smaller than "InterRatCsThd2FRscp".
The value of this parameter must be larger than "InterRatCsThd2DRscp".
The value of this parameter must be smaller than "InterRatR99PsThd2FRscp".

The value of this parameter must be smaller than "InterRatHThd2FRscp".
The value of this parameter must be larger than "InterRatR99PsThd2DRscp".
The value of this parameter must be larger than "InterRatHThd2DRscp".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "NcovHoOn2GldInd" in "SET UINTERRATHONCOV" is set to ON.

None
None
None
None
None
None
None
None
None
None
None
None
None
None
The value of this parameter must be set based on the following formula:
("IntraRelThdFor1ACSVP" - "Hystfor1A" / 2) < ("IntraRelThdFor1BCSVP" + "Hystfor1B" / 2).
("IntraRelThdFor1ACSNVP" - "Hystfor1A" / 2) < ("IntraRelThdFor1BCSNVP" + "Hystfor1B" / 2).
("IntraRelThdFor1APS" - "Hystfor1A"/2) < ("IntraRelThdFor1BPS" + "Hystfor1B"/2)
("IntraRelThdFor1ACSVP" - "Hystfor1A"/2) < ("IntraRelThdFor1BCSVP" + "Hystfor1B"/2)
("IntraRelThdFor1ACSNVP" - "Hystfor1A"/2) < ("IntraRelThdFor1BCSNVP" + "Hystfor1B"/2)
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None

"CellOverrunThd" >= "CellUnderrunThd".

"CellOverrunThd" >= "CellUnderrunThd".
None
"UlLdrTrigThd" >= "UlLdrRelThd";
"UlOlcTrigThd" > "UlLdrTrigThd";
"UlNonCtrlThdForOther"(See "ADD UCELLCAC") >= "UlLdrTrigThd".
"UlLdrTrigThd" >= "UlLdrRelThd";
"UlOlcRelThd" >= "UlLdrRelThd".
"DlLdrTrigThd" >= "DlLdrRelThd";
"DlOlcTrigThd" > "DlLdrTrigThd";
"DlOtherThd"(See "ADD UCELLCAC") >= "DlLdrTrigThd".

"DlLdrTrigThd" >= "DlLdrRelThd";
"DlOlcRelThd" >= "DlLdrRelThd".
"UlOlcTrigThd" > "UlLdrTrigThd";
"UlOlcTrigThd" >= "UlOlcRelThd";
"UlOlcTrigThd" >= "UlNonCtrlThdForHo"(See "ADD UCELLCAC").
"UlOlcTrigThd" >= "UlOlcRelThd";
"UlOlcRelThd" >= "UlLdrRelThd".
"DlOlcTrigThd" >= "DlOlcRelThd";
"DlOlcTrigThd" > "DlLdrTrigThd";
"DlOlcTrigThd" >= "DlCellTotalThd".
"DlOlcTrigThd" >= "DlOlcRelThd";
"DlOlcRelThd" >= "DlLdrRelThd".
None
"HsupAuRetrnsLdTrigThd" >= "HsupAuRetrnsLdRelThd"
"HsupAuRetrnsLdTrigThd" >= "HsupAuRetrnsLdRelThd"

"TrigRatioforUlRTWP" >= "RelRatioforUlRTWP"

"TrigRatioforUlRTWP" >= "RelRatioforUlRTWP"
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The value of this parameter must not be larger than "DlHoCeCodeResvSf" in "ADD UCELLCAC". The compar
factors is based on the number following the acronym "SF", for example, SF32>SF8.
None
None
The value of this parameter must not be larger than "UlHoCeResvSf". The comparison betw
based on the number following the acronym "SF", for example, SF32>SF8.
The value of this parameter must not be larger than "DlHoCeCodeResvSf" in "ADD UCELLCAC". The compar
factors is based on the number following the acronym "SF", for example, SF32>SF8.
None
This parameter is valid only when INTER_FREQ_HHO_SWITCH of the "HoSwitch" in "SET UCORRMALGOSWITCH" is set to
None
None
None
None
None
None
None
None
None
None
None
None
When "InterFreqReportMode" is set to PERIODICAL_REPORTING, this parameter is valid and must be configured.
None
None
None
None
None
None
None
None
None
None
None
None

None
None
None
None
None
None
None
None
None
None
None
None

"MtchMinPerc0" >= "MtchMinPerc15".

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This paramter is valid only when "STTD support indicator" of "ADD UCELLSETUP" is set to STTD_Supported.
None
This parameter is consistent with "FACH ID" in "ADD UFACH", "ADD UFACHDYNTFS", and "ADD UFACHLOCH".
None
None
If this parameter is set through both the "ADD UCELLMCDRD" and "SET UMCDRD" commands, the parameter set through th
command takes precedence over that set through the "SET UMCDRD" command.
None
None
None
None
None
None
None
None
This parameter is required when the "InterFreqInterRatMeasInd" parameter is set to INTER_FREQ, INTER_RAT or INTER_FR
This parameter is not required when the "InterFreqInterRatMeasInd" parameter is set to NOT_REQUIRE.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"SpucHeavy" >= "SpucLight";
"SpucLight" >= "SpucHyst".
"SpucHeavy" >= "SpucLight";
100 >= "SpucHeavy" + "SpucHyst".
"SpucLight" >= "SpucHyst";
100 >= "SpucHeavy" + "SpucHyst".
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "InterRatReportMode" in "SET UINTERRATHOCOV" or "ADD UCELLINTERRATHOCOV" is set
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
1. This parameter is valid when "RedirSwitch" is set to ONLY_TO_INTER_FREQUENCY or ONLY_TO_INTER_RAT.
2. If the value of this parameter is set in both the "SET UREDIRECTION" and "ADD UCELLREDIRECTION" commands, the va
UCELLREDIRECTION" command prevails.


1. This parameter is valid when "RedirBandInd" is not set to BandIndNotUsed.

1. This parameter is valid when "RedirUARFCNUplinkInd" is set to TRUE.

2. This parameter is valid when "RedirBandInd" is set to BandIndNotUsed.
3. If the value of this parameter is set in both the "SET UREDIRECTION" and "ADD UCELLREDIRECTION" commands, the v
None
None
None
None
None
The value of this parameter must not be smaller than "RlMinDlPwr".
The value of this parameter must not be larger than "RlMaxDlPwr".
None
None
None
None
None
This parameter is valid only when "QualMeas" is set to CPICH_ECNO.
This parameter is valid only when "QualMeas" is set to CPICH_ECNO.
None
None
None
None
This parameter is required when the "QrxlevminExtSup" parameter is set to TRUE but not required when the "QrxlevminExtSu
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "NonhcsInd" is set to CONFIGURED.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"RTWP Heavy Threshold" must be greater than "RTWP Light Threshold".
"RTWP Heavy Threshold" must be greater than "RTWP Light Threshold".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "CellIDChgSwitch" is ON
None
None
None
None
None
None
None
None
None
None
T3212 needs to be set when "CNDomainId" in "ADD UCNDOMAIN" is set to CS_DOMAIN; T3212 does not need to be set wh
UCNDOMAIN" is set to PS_DOMAIN.
ATT needs to be set when "CNDomainId" in "ADD UCNDOMAIN" is set to CS_DOMAIN; ATT does not need to be set when "C
UCNDOMAIN" is set to PS_DOMAIN.
NMO needs to be set when "CNDomainId" in "ADD UCNDOMAIN" is set to PS_DOMAIN; NMO does not need to be set when
UCNDOMAIN" is set to CS_DOMAIN.
DRXCycleLenCoef needs to be set only when "CNDomainId" in "ADD UCNDOMAIN" is set to CS_DOMAIN or PS_DOMAIN.
None
None
None
None
None
When "CNProtclVer" in "ADD UCNNODE" is set to R99, set SupportCRType to CR527_SUPPORT or CR527_NOT_SUPPOR
UCNNODE" is set to R4, set SupportCRType to CR528_SUPPORT or CR528_NOT_SUPPORT; when "CNProtclVer" in "ADD
SupportCRType to CR529_SUPPORT or CR529_NOT_SUPPORT; when "CNProtclVer" in "ADD UCNNODE" is set to R6, the
be set.
None
None
None
When "TnlBearerType" in "ADD UCNNODE" is set to IP_TRANS, RTCPSwitch needs to be set.
When "RTCPSwitch" in "ADD UCNNODE" is set to ON, RTCPBWRatio needs to be set.
When "CNDomainId" in "ADD UCNNODE" is set to CS_DOMAIN, Switch3GPP25415CR0125 needs to be set.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
CountCThreshold needs to be set when "CounterCheckSwitch" in "SET UCNTCHK" is set to ON; CountCThreshold does not n
"CounterCheckSwitch" in "SET UCNTCHK" is set to OFF.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
T314 should be set greater than T302*N302
T315 should be set greater than T302*N302
None
None
None
None
None
None
DRA_THROU_DCCC_SWITCH,DRA_BASE_ADM_CE_BE_TTI_RECFG_SWITCH,DRA_BASE_COVER_BE_TTI_RECFG_S
TI_RECFG_SWITCH and DRA_HSUPA_DCCC_SWITCH are valid when DRA_DCCC_SWITCH is set to ON;
For BE service,DRA_HSDPA_STATE_TRANS_SWITCH and DRA_HSUPA_STATE_TRANS_SWITCH are valid when
DRA_PS_BE_STATE_TRANS_SWITCH is set to ON;
For RT service,DRA_HSDPA_STATE_TRANS_SWITCH and DRA_HSUPA_STATE_TRANS_SWITCH are valid when
DRA_PS_NON_BE_STATE_TRANS_SWITCH is set to ON;
None
None
None
None
PS_RAB_DOWNSIZING_SWITCH is valid when DRA_DCCC_SWITCH in "DraSwitch" is set to ON.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None

"Max capability normal load" > "Max capability middle load" > "Sharing out capability middle load".


None
None
None
None
When the value of "UlMidRateCalc" is HAND_APPOINT, the following relationship must be satisfied:
"UlDcccRateThd" <= "UlMidRateThd".
When the value of "DlMidRateCalc" is HAND_APPOINT, the following relationship must be satisfied:
"DlDcccRateThd" <= "DlMidRateThd".
The low activity rate adjustment function is invalid when "LittleRateThd" >= "UlDcccRateThd" and "LittleRateThd" >= "DlDcccR
None
None
None
None
The parameter is valid when "UlRateUpAdjLevel" in "SET UDCCC" is set to 3_Rates, or "UlRateDnAdjLevel" in "SET UDCCC"
The parameter is valid when "UlMidRateCalc" in "SET UDCCC" is set to HAND_APPOINT, and the following relationship must
"UlDcccRateThd" <= "UlMidRateThd".
None
None
This parameter is valid when the "DlRateUpAdjLevel" in "SET UDCCC" is set to 3_Rates, or when "DlRateDnAdjLevel" in "SET
This parameter is valid when the "DlMidRateCalc" in "SET UDCCC" is set to HAND_APPOINT, and the following relationship m
"DlDcccRateThd" <= "DlMidRateThd".
None
None
None
None
None
None
None
None
The value of this parameter must be smaller than "IMSIEnd".
The value of this parameter must be greater than "IMSIStart".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This paramter is valid only when "EdchIubCongCheckSwitch" in "SET UDPUCFGDATA" is set ON.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when the "LdbDRDchoice" parameter is set to POWER.
This parameter is valid only when the "CodeBalancingDrdSwitch" parameter is set to ON through the "SET UDRD" command.
This parameter is required only when the "ReDirUARFCNUplinkInd" parameter is set to TRUE.
BAND1
BAND2
Special UARFCNs: {12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287}
BAND3
BAND4
Special UARFCNs: {1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862}
BAND5
Special UARFCNs: {782, 787, 807, 812, 837, 862}
BAND6
BAND7
Special UARFCNs: {2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687}
BAND8
BAND9
BandIndNotUsed
[0-16383]
BAND1
BAND2
Special UARFCNs: {412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687}
BAND3
BAND4
Special UARFCNs: {1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087}
BAND5
Special UARFCNs: {1007, 1012, 1032, 1037, 1062, 1087}
BAND6
BAND7
Special UARFCNs: {2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912}
BAND8
BAND9
BandIndNotUsed
[0-16383]
None
None
If this parameter is set by running both "ADD UCELLDRD" and "SET UDRD" commands, the parameter setting in the "ADD UC
effect.
None
None
None
None
None
None
None
None
None
None
None
None
None
Valid when "ChoiceRptUnitForCQIE" is set to TEN_MSEC
Valid when "ChoiceRptUnitForCQIE" is set to MIN
None
None
Valid when "ChoiceRptUnitForCQIF" is set to TEN_MSEC
Valid when "ChoiceRptUnitForCQIF" is set to MIN
None
When "DsacAutoSwitch"is set to ON,the parameter need configuring;else,need not.

None
None
This parameter cannot be greater than "DSS Dea Inter-Freq HO Protection Duration" or "DSS Dea Inter-RAT HO Protection D
None
This parameter must be consistent with the handover protection duration for the urgent spectrum withdrawal of GSM.
None
None
None
This parameter is valid when "Dtxvalid" is set to ON.

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"AmrThd6A1" <= "AmrThd6B1"
"AmrThd6A1" <= "AmrThd6B1"
None
"WAmrThd6A1" <= "WAmrThd6B1"
"WAmrThd6A1" <= "WAmrThd6B1"
None
"VoipThd6A1" <= "VoipThd6B1"
"VoipThd6A1" <= "VoipThd6B1"
"BeThd6A1" <= "BeThd6B1"

"BeThd6A1" <= "BeThd6B1";
"BeThd6B1" < "BeThd6A2";
"BeThd6A2" <= "BeThd6B2";
"BeThd6B1" < "BeThd6A2";
"BeThd6A2" <= "BeThd6B2"

This parameter must be smaller than "UpRatioFor2msTo10msBaseRtwp";
This parameter must be smaller than "UpRatioFor2msTo10msBaseCE";
This parameter must be greater than "LowRatioFor2msTo10ms";
This parameter must be smaller than "RatioFor10msTo2ms";
This parameter must be greater than "LowRatioFor2msTo10ms";
This parameter must be smaller than "RatioFor10msTo2ms";
This parameter must be greater than "UpRatioFor2msTo10msBaseRtwp";
This parameter must be greater than "UpRatioFor2msTo10msBaseCE";
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this paramter is not zero, it is valid only when "NBscIndex" in "ADD UNBSC" is added.
None
None
None
This paramter is valid only when "CnOpGrpIndex" in "ADD UCNOPERGROUP" is added.
None
None
This paramter is valid only when "CfgRacInd" is set to REQUIRE.
None
None
None
None
None
None
None
This paramter is valid only when "UseOfHcs" is set to TRUE.

This parameter is valid only when "UseOfHcs" is set to TRUE.
None
None
None
None
None
None
None
None
None
None
None
None
None
This paramter is valid only when "CellHostType" is set to DOUBLE_HOST_OUT_POOL.
This paramter is valid only when "CellHostType" is set to DOUBLE_HOST_OUT_POOL.
None
None
None
None
None
This paramter is valid only when "QqualminInd" is set to TRUE.
None
This paramter is valid only when "QrxlevminInd" is set to TRUE.
This paramter is valid only when "QrxlevminInd" is set to TRUE.
This paramter is valid only when "QrxlevminExtSup" is set to TRUE.
None
This paramter is valid only when "MaxAllowedUlTxPowerInd" is set to TRUE.
None
This paramter is valid only when "UseOfHcs" is set to TRUE.

This parameter is valid only when "UseOfHcs" is set to TRUE.
None
This parameter is valid only when "CP1SupInd" is set to CP1_Supported.

None
This parameter is valid when the OVERLAY_SWITCH is ON The OVERLAY_SWITCH is in "HoSwitch" in "SET UCORRMALG
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Configured only when the "Channel Code Type" is configured as CONVOLUTIONAL.
None
None
None
None
None
None
None
None
This paramter is valid only when "Number of TFs" is set to D2 or D3.
This paramter is valid only when "Number of TFs" is set to D3.
None
None
None
None
None
None
None
This parameter can only be set to 1 when the "PwrCtrlAlg" parameter is set to ALGORITHM2.
None
None
The code-resource-saving mode is applicable to narrowband AMR services only when this parameter is set to ON and the "All
parameter is set to TRUE through the "ADD UCELLFRC" command.
This parameter is valid only when the code-resource-saving mode is applicable to narrowband AMR services, that is, when the
parameter is set to ON and the "AllowedSaveCodeResource" parameter is set to TRUE through the "ADD UCELLFRC" comm
None
This parameter is valid only when the DRA_DCCC_SWITCH under the "DraSwitch" parameter is switched on through the "SE
command.
This parameter is valid only when the DRA_DCCC_SWITCH under the "DraSwitch" parameter is switched on through the "SE
command.
None
None
None
None
None
None
None
None
None
This parameter can be used for selection of the initial rate for HSUPA BE services only when the DRA_DCCC_SWITCH under
the DRA_HSUPA_DCCC_SWITCH under the "DraSwitch" parameter are set to on through the "SET UCORRMALGOSWITCH
None
None
This parameter is required when the "ImsBearEnhancedSwitch" parameter is set to ON.
None
None
None
None
RlcPduMaxSizeForUlL2Enhance is must bigger than or equal to RlcPduMinSizeForUlL2Enhance
RlcPduMaxSizeForUlL2Enhance is must bigger than or equal to RlcPduMinSizeForUlL2Enhance
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
command prevails.
command prevails.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None


None


None
None
None
None
The value of this parameter must not larger than "MaxCellInActiveSet" of "SET UINTRAFREQHO" or "ADD UCELLINTRAFRE
None
None
None
None
None
None
None
None
None
None
"TbSizeIndex1" < "TbSizeIndex2" < "TbSizeIndex3" < "TbSizeIndex4"
This parameter is valid when the "TbNum" parameter is set to D1, D2, D3, or D4.
This parameter is valid when the "TbNum" parameter is set to D2, D3, or D4.
This parameter is valid when the "TbNum" parameter is set to D3 or D4.

This parameter is valid when the "TbNum" parameter is set to D4.
None
None
None
None
None
None
None
None
None
"Min Transmit Power of PCPICH" <= "PCPICH Transmit Power" <= "Max Transmit Power of PCPICH"
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when the value of "ServiceNum" is greater than 0.
None
None
The value of this parameter must meet the following requirements:

1. The value of this parameter must be greater than the value of "SccpchType2CodeFirst".
2. When 16QAM modulation is used, "SccpchType2CodeLast" - "SccpchType2CodeFirst" is less than or equal to 5.
3. When QPSK modulation is used, "SccpchType2CodeLast" - "SccpchType2CodeFirst" is less than or equal to 10.
None
1. When "ModuType" is set to QPSK, this parameter is set to D2 or D3.

2. When "ModuType" is set to 16QAM, this parameter is set to D4 or D5.
None
None
None
None
This parameter is valid when the "TAC_FUNC" parameter in "ADD UIMEITAC" is set to Fast_Dormancy.
This parameter is valid when the "FastDormancy" parameter in "ADD UIMEITAC" is set to ON.
This parameter must be greater than or equal to "ImsiRtMin" in "ADD UIMSIIDNNSCNIDMAP".
This parameter must be less than or equal to "ImsiRtMax" in "ADD UIMSIIDNNSCNIDMAP".

None
None
The parameter must be less than or equal to "ImsiMax" in "ADD UIMSISNAMAP".
The parameter must be greater than or equal to "ImsiMin" in "ADD UIMSISNAMAP".
None
None
None
None
None
None
None
None
None
None
None
None
None
The value of this parameter must be smaller than "InterFreqCsThd2FEcN0".
The value of this parameter must be larger than "InterFreqCsThd2DEcN0".
The value of this parameter must be smaller than "InterFreqR99PsThd2FEcN0".
The value of this parameter must be smaller than "InterFreqHThd2FEcN0".

The value of this parameter must be greater than "InterFreqR99PsThd2DEcN0".
The value of this parameter must be greater than "InterFreqHThd2DEcN0".
The value of this parameter must be smaller than "InterFreqCsThd2FRscp".
The value of this parameter must be greater than "InterFreqCsThd2DRscp".
The value of this parameter must be smaller than "InterFreqR99PsThd2FRscp".
The value of this parameter must be smaller than "InterFreqHThd2FRscp".

The value of this parameter must be greater than "InterFreqR99PsThd2DRscp".
The value of this parameter must be larger than "InterFreqHThd2DRscp".
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "InterFreqReportMode" is set to "EVENT_TRIGGER".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when "SIB11Ind" is set to TRUE.
None

None
None
None
This parameter is valid only when "BlindHOFlag" is set to TRUE.
None
None
None
None
None
None
This paramter is valid only when "InterNCellQualReqFlag" is set to TRUE.
This paramter is valid only when "InterNCellQualReqFlag" is set to TRUE.
None
None

None
None
None
None
None
None
None
The value of this parameter must be smaller than "InterRatCsThd2FEcN0".
The value of this parameter must be larger than "InterRatCsThd2DEcN0".

The value of this parameter must be smaller than "InterRatR99PsThd2FEcN0".
The value of this parameter must be smaller than "InterRatHThd2FEcN0".
The value of this parameter must be larger than "InterRatR99PsThd2DEcN0".
The value of this parameter must be larger than "InterRatHThd2DEcN0".
The value of this parameter must be smaller than "InterRatCsThd2FRscp".
The value of this parameter must be larger than "InterRatCsThd2DRscp".

The value of this parameter must be smaller than "InterRatR99PsThd2FRscp".
The value of this parameter must be smaller than "InterRatHThd2FRscp".
The value of this parameter must be larger than "InterRatR99PsThd2DRscp".
The value of this parameter must be larger than "InterRatHThd2DRscp".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None

None
None
None
None
None
None
None
None
None
None
None
None
("IntraRelThdFor1ACSVP" - "Hystfor1A" / 2) < ("IntraRelThdFor1BCSVP" + "Hystfor1B" / 2).
("IntraRelThdFor1ACSNVP" - "Hystfor1A" / 2) < ("IntraRelThdFor1BCSNVP" + "Hystfor1B" / 2).
("IntraRelThdFor1ACSVP" - "Hystfor1A"/2) < ("IntraRelThdFor1BCSVP" + "Hystfor1B"/2)
("IntraRelThdFor1ACSNVP" - "Hystfor1A"/2) < ("IntraRelThdFor1BCSNVP" + "Hystfor1B"/2)
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None

None
None
None
None
None
None
None
None
None
This parameter is valid only when the "Traffic Type" parameter is set to "SPI". When the "Match Type" parameter is set to "IP",
displayed. When the "Match Type" parameter is set to "Port", only the port entry box is displayed. When the "Match Type" para
the IP entry box and the port entry box are displayed.
This parameter is valid only when the "Traffic Type" parameter is set to "SPI".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"PlmnValTagMax" > "PlmnValTagMin".
None
None
None
None
LAC needs to be set when "QryType" in "DSP USNAINFO" is set to BY_LAC or BY_SNAC; LAC does not need to be set when
is set to BY_PLMN.
"LdrFirstPri","LdrSecondPri","LdrThirdPri","LdrFourthPri" must be set differently.
None
None
When "ChoiceRprtUnitForDlBasicMeas" is set to MIN,the value of this parameter must satisfy the following relationship:
"IntraFreqLdbPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
When "ChoiceRprtUnitForDlBasicMeas" is set to TEN_MSEC,the value of this parameter must satisfy the following relationshi
"IntraFreqLdbPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
"PucPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
"PucPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
When "ChoiceRprtUnitForUlBasicMeas" and "ChoiceRprtUnitForDlBasicMeas" are set to MIN,the value of this parameter mus
"LdrPeriodTimerLen" > 2 * 60 * "MinForUlBasicMeas";
"LdrPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
When "ChoiceRprtUnitForUlBasicMeas" and "ChoiceRprtUnitForDlBasicMeas" are set to TEN_MSEC,the value of this parame
relationship:
"LdrPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForUlBasicMeas";
"LdrPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
"OlcPeriodTimerLen" > 2 * 60 * 1000 * "MinForUlBasicMeas";
"OlcPeriodTimerLen" > 2 * 60 * 1000 * "MinForDlBasicMeas";
relationship:
"OlcPeriodTimerLen" > 2 * 10 * "TenMsecForUlBasicMeas";
"OlcPeriodTimerLen" > 2 * 10 * "TenMsecForDlBasicMeas".
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForUlBasicMeas" is set to TEN_MSEC,and it must satisfy the following relat
"TenMsecForUlBasicMeas" *10 < "LdrPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForUlBasicMeas" *10 < "OlcPeriodTimerLen" /2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
This parameter is valid only when "ChoiceRprtUnitForUlBasicMeas" is set to MIN,and it must satisfy the following relationship:
"MinForUlBasicMeas" * 60 < "LdrPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForUlBasicMeas" * 60000 < "OlcPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
None
None
This parameter is valid only when "ChoiceRprtUnitForDlBasicMeas" is set to TEN_MSEC,and it must satisfy the following relat
"TenMsecForDlBasicMeas" *10 < "IntraFreqLdbPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPE
"TenMsecForDlBasicMeas" *10 < "PucPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForDlBasicMeas" *10 < "LdrPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForDlBasicMeas" *10 < "OlcPeriodTimerLen"/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
This parameter is valid only when "ChoiceRprtUnitForDlBasicMeas" is set to MIN,and it must satisfy the following relationship:
"MinForDlBasicMeas" * 60 < "IntraFreqLdbPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60 < "PucPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60 < "LdrPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60000 < "OlcPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForHsdpaPwrMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForHsdpaPwrMeas" is set to MIN.
None
None
This parameter is valid only when "ChoiceRprtUnitForHsdpaRateMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForHsdpaRateMeas" is set to MIN.
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForUlOlcMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForUlOlcMeas" is set to MIN.
None
None
None
This parameter is valid only when "ChoiceRprtUnitForDlOlcMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForDlOlcMeas" is set to MIN.
None
None
This parameter is valid only when "ChoiceRprtUnitForHsupaRateMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForHsupaRateMeas" is set to MIN.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is used with the "ADD UMBMSALARMSERVICE" command to enable the no MBMS data check. If the "ADD U
specified service has no data on the Iu interface within the period specified by this parameter, an alarm is reported.The param
on the equipment.
None
None
None
None
None
None


None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid olny when "MBMS Control Switch" is ON.

None
None
None
None
None
None
None
This paramter is valid only when "MbscNcovHoOn2GldInd" in "SET UMBSCCRRM" is set ON.
None
None
None
None
None
The relationship of parameters must be set as follows:
"Mcch Mod Period Coefficient" > "DRX cycle length coefficient" in "ADD UCNDOMAIN".
"Mcch Access Period Coefficient" > "Mcch Repetition Period Coefficient".
"Mcch Access Period Coefficient" > "Mcch Repetition Period Coefficient".
None
None
None
None
None
This parameter is valid when "TstSwitch" is set to ON.
None
None
None
None
None
Before enable ALG function,must use "SET UNATSWITCH" to enbale NAT switch.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When "CARRYLNKT" is SAAL-SCTP, this parameter is valid.
None
When "STACKMODTYPE" is ATMTODUAL or IPTODUAL, this parameter is valid.
None
None
None
None
None
None
None
None
None
None
None
None
None
1. If the NodeB is configured with the NCP through "ADD UNCP" or configured with the CCP through "ADD UCCP", the transm
2. If a NodeB OM channel is set up, the transmission type cannot be modified.
3. If the NodeB is configured with adjacent nodes through "ADD ADJNODE", the transmission type cannot be modified.
4. If the NodeB is configured with the electrical serial number through "ADD UNODEBESN" and the transmission type is suppo
transmission, the transmission type cannot be modified.
The parameter should be configured when "TnlBearerType" is modified from ATM to IP or dual stack ATM/IP.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
CsNriCfgMode may be set to SUPP_IUFLEX when "CNProtclVer" in "ADD UCNNODE" is set to R5 or any later version
CsNriCfgMode may be set to SUPP_MOCN or SUPP_IUFLEX_MOCN when "CNProtclVer" in "ADD UCNNODE" is set to R6
The network resource identifier (NRI) needs to be set when MOCN or Iu-Flex is supported.
None
CSNRILength needs to be set when the value of "CsNriCfgMode" in "SET UOPERATORCFGPARA" is set to SUPP_IUFLEX,
SUPP_IUFLEX_MOCN; CSNRILength does not need to be set when the value of "CsNriCfgMode" in "SET UOPERATORCFG
PSNRILength needs to be set when the value of "PsNriCfgMode" in "SET UOPERATORCFGPARA" is set to SUPP_IUFLEX,
SUPP_IUFLEX_MOCN; PSNRILength does not need to be set when the value of "PsNriCfgMode" in "SET UOPERATORCFG
NullNRI must be set When the value of "CsNriCfgMode" in "SET UOPERATORCFGPARA" is set to SUPP_IUFLEX or SUPP_
or the value of "PsNriCfgMode" in "SET UOPERATORCFGPARA" is set to SUPP_IUFLEX or SUPP_IUFLEX_MOCN.
None
None
CsInfoUpdTmr needs to be set when "CsInfoUpdFlag" in "SET UOPERATORCFGPARA" is set to ON; CsInfoUpdTmr does no
"CsInfoUpdFlag" in "SET UOPERATORCFGPARA" is set to OFF.
PsInfoUpdTmr needs to be set when "PsInfoUpdFlag" in "SET UOPERATORCFGPARA" is set to ON; PsInfoUpdTmr does no
"PsInfoUpdFlag" in "SET UOPERATORCFGPARA" is set to OFF.
None
None
None
None
When "MOCNSupport" in "SET UOPERATORSHARINGMODE" is set to YES, DefaultCnOp optionally needs to be set.Otherw
When "MOCNSupport" in "SET UOPERATORSHARINGMODE" is set to YES, MocnControlSwitch needs to be set.Otherwise,
None
None
The value of this parameter must be smaller than "DlRateThreshold2".
The value of this parameter must be greater than "DlRateThreshold8".
None
The value of this parameter must be smaller than "UlRateThreshold2".
The value of this parameter must be greater than "UlRateThreshold8".
None
This parameter forms an SPI mapping table with "UserPriority", "THPClass", and "SPI".
This parameter forms an SPI mapping table with "TrafficClass", "THPClass", and "SPI".
This parameter is required when the "TrafficClass" parameter is set to INTERACTIVE. The mapping relationship between the
INTERACTIVE service and its corresponding class can be set through command "SET UTHPCLASS".
This parameter forms an SPI mapping table with "TrafficClass", "UserPriority", and "THPClass".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
For the BE users with the same "TrafficClass", "THPClass" and "BearType" values, make sure:
"UlGBR" of GOLD users ("UserPriority" is set to GOLD) >= "UlGBR" of SILVER users ("UserPriority" is set to SILVER) >= "UlG
("UserPriority" is set to COPPER).
"DlGBR" of GOLD users ("UserPriority" is set to GOLD) >= "DlGBR" of SILVER users ("UserPriority" is set to SILVER) >= "DlG
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"Min Transmit Power of PCPICH" <= "PCPICH Transmit Power" <="Max Transmit Power of PCPICH"
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The ASCs are configured through "ADD UPRACHASC".

None
None
None
"Available Signature Start Index"should be no greater than "Available Signature End Index".
"Available Signature End Index"should be less than the number of preamble signatures. The preamble signature is configured
"ADD UPRACHBASIC".
None
This parameter is valid when "Access Service Class" is set to ASC2,ASC3,ASC4,ASC5,ASC6 or ASC7.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Either "Gain Factor BetaC" or "Gain Factor BetaD" should be set to 15.
Either "Gain Factor BetaC" or "Gain Factor BetaD" should be set to 15.
None
None
None
None
None
None
None
None
1. For the detection timers that do not need to configure conversational services, the related T1 and T2 must be 0 at the same
2. For the detection timers that need to configure conversational services, the related T1 and T2 must not be 0 at the same tim
1. For the detection timers that do not need to configure conversational services, the related T1 and T2 must be 0 at the same
2. For the detection timers that need to configure conversational services, the related T1 and T2 must not be 0 at the same tim
1. For the detection timers that do not need to configure streaming services, the related T1 and T2 must be 0 at the same time
2. For the detection timers that need to configure streaming services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure streaming services, the related T1 and T2 must be 0 at the same time
2. For the detection timers that need to configure streaming services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure interactive services, the related T1 and T2 must be 0 at the same time
2. For the detection timers that need to configure interactive services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure interactive services, the related T1 and T2 must be 0 at the same time
2. For the detection timers that need to configure interactive services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure background services, the related T1 and T2 must be 0 at the same tim
2. For the detection timers that need to configure background services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure background services, the related T1 and T2 must be 0 at the same tim
2. For the detection timers that need to configure background services, the related T1 and T2 must not be 0 at the same time.
1. For the detection timers that do not need to configure FAST DORMANCY user in CELL_PCH, the related T1 and T2 accord
the same time. 2. For
the detection timers that need to configure FAST DORMANCY user in CELL_PCH, the related T1 and T2 according to service
time.
1. For the detection timers that do not need to configure IMS signaling services, the related T1 and T2 must be 0 at the same
2. For the detection timers that need to configure IMS signaling services, the related T1 and T2 must not be 0 at the same time
1. For the detection timers that do not need to configure IMS signaling services, the related T1 and T2 must be 0 at the same
2. For the detection timers that need to configure IMS signaling services, the related T1 and T2 must not be 0 at the same time
1. For the detection timers that do not need to configure FAST DORMANCY user in CELL_DCH, the related T1 and T2 accord
the same time.
2. For the detection timers that need to configure FAST DORMANCY user in CELL_DCH, the related T1 and T2 according to s
same time.
1. For the detection timers that do not need to configure FAST DORMANCY user in CELL_FACH, the related T1 and T2 accor
the same time. 2. For the detection timers that need to configure FAST DORMANCY user in CELL_FACH, the related T1 and
must not be 0 at the same time.
None
None
None
None
None
None
None
None
None
None
"PTTDH2FTvmThd" < "PTTF2DHTvmThd";"PTTDH2FTvmThd" < "PTTEF2DHTvmThd".

None
None
None
None
None
None
None
"PTTF2PTvmThd" < "PTTF2DHTvmThd";"PTTF2PTvmThd" < "PTTEF2DHTvmThd"
None
None
"PTTDH2FTvmThd" < "PTTF2DHTvmThd";

"PTTF2PTvmThd" < "PTTF2DHTvmThd"
None
"PTTDH2FTvmThd" < "PTTEF2DHTvmThd";
"PTTF2PTvmThd" < "PTTEF2DHTvmThd"
None
None
None
None
None
Valid when "BEQosPerform" is set to YES;

"BeUlAct2" and "BeUlAct3" must be None when "BeUlAct1" is set to None;
"BeUlAct2" and "BeUlAct3" must not be equal with "BeUlAct1" when "BeUlAct1" is not set to None.

"BeUlAct2" must be None when "BeUlAct1" is set to None;
"BeUlAct2" must not be equal with "BeUlAct1" when "BeUlAct1" is not set to None.
"BeUlAct3" must be None when "BeUlAct2" is set to None;
"BeUlAct3" must not be equal with "BeUlAct2" and "BeUlAct1" when "BeUlAct2" is not set to None.

"BeUlAct3" must be None when "BeUlAct1" or "BeUlAct2" is set to None;
Valid when "BEQosPerform" is set to YES.

"BeDlAct2" and "BeDlAct3" must be None when "BeDlAct1" is set to None;
"BeDlAct2" and "BeDlAct3" must not be equal with "BeDlAct1" when "BeDlAct1" is not set to None.

"BeDlAct2" must be None when "BeDlAct1" is set to None;
"BeDlAct2" must not be equal with "BeDlAct1" when "BeDlAct1" is not set to None;
"BeDlAct3" must be None when "BeDlAct2" is set to None;
"BeDlAct3" must not be equal with "BeDlAct2" and "BeDlAct1" when "BeDlAct2" is not set to None.

"BeDlAct3" must be None when "BeDlAct1" or "BeDlAct2" is set to None;
"BeDlAct3" must not be equal with "BeDlAct1" when "BeDlAct1" is not set to None.
"BeDlAct3" must not be equal with "BeDlAct2" when "BeDlAct2" is not set to None.
Valid when "AMRQosPerform" is set to YES.

This parameter is valid when the "VPQosPerform" is set to YES.
This parameter is valid when the "VPQosPerform" is set to YES.
This parameter is valid when the "BEQosPerform" is set to YES and "BeUlEvTrigInd" is set to SINGLE.
This parameter is valid when the "BEQosPerform" is set to YES and "BeUlEvTrigInd" is set to SINGLE.

None
None
None
This parameter is valid when "InterRatReportMode" in "SET UINTERRATHOCOV" or "ADD UCELLINTERRATHOCOV" is set
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The value of this parameter must be set to meet the following conditions:
100 x "MaxQueueTimeLen" > "PollTimerLen".
100 x "MaxQueueTimeLen" > "PollTimerLen".
None
None
None
None
None
None
None
None
"Random Back-off Upper Limit" >= "Random Back-off Lower Limit".
"Random Back-off Upper Limit" >= "Random Back-off Lower Limit".
None
None
None
None
None
None
None
[Maximum Ec/N0 Up Step] is not smaller than [Ec/N0 Adjustment Step]
[Maximum Ec/N0 Down Step] is not smaller than [Ec/N0 Adjustment Step]
1. [Maximum Ec/N0 Up Step] is not smaller than [Ec/N0 Adjustment Step].
2. [Maximum Ec/N0 Down Step] is not smaller than [Ec/N0 Adjustment Step].
None
None
[Maximum Ec/N0 Value] is larger than [Minimum Ec/N0 Value]
[Maximum Ec/N0 Value] is larger than [Minimum Ec/N0 Value]
None
None
This parameter is valid when "RedirSwitch" is set to ONLY_TO_INTER_FREQUENCY or ONLY_TO_INTER_RAT.
This parameter is valid when "RedirBandInd" is not set to BandIndNotUsed.

1. This parameter is valid when "RedirUARFCNUplinkInd" is set to TRUE.
2. This parameter is valid when "RedirBandInd" is set to BandIndNotUsed.
None

"DLOVSFSF">"DLCODENO".
"DLOVSFSF">"DLCODENO".
"DLOVSFSF">="DLCODENO".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This paramter is valid only when "Cell Dynamic ShutDown Switch for RNC" is set to ON.
This paramter is valid only when "Cell Dynamic ShutDown Switch for RNC" is set to ON.
None
None
None
This parameter defines an offset relative to the "NCountingThd" parameter.
None
None
The value of this parameter must be smaller than the value of the "RecountingPeriod" parameter under the "SET URNCMBMS
The value of this parameter must be larger than the value of the "UpLimitCountingTime" parameter under the "SET URNCMBM
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the "RrcCause" parameter is set to EMERGCALLEST or MBMSCALLEST, this parameter cannot be set to FACH.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"IntraFreqLdbPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
"IntraFreqLdbPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
"PucPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
"PucPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
"LdrPeriodTimerLen" > 2 * 60 * "MinForUlBasicMeas";
"LdrPeriodTimerLen" > 2 * 60 * "MinForDlBasicMeas";
relationship:
"LdrPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForUlBasicMeas";
"LdrPeriodTimerLen" * 1000 > 2 * 10 * "TenMsecForDlBasicMeas".
"OlcPeriodTimerLen" > 2 * 60 * 1000 * "MinForUlBasicMeas";
"OlcPeriodTimerLen" > 2 * 60 * 1000 * "MinForDlBasicMeas";
relationship:
"OlcPeriodTimerLen" > 2 * 10 * "TenMsecForUlBasicMeas";
"OlcPeriodTimerLen" > 2 * 10 * "TenMsecForDlBasicMeas".
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForUlBasicMeas" is set to TEN_MSEC,and it must satisfy the following relat
"TenMsecForUlBasicMeas" *10 < "LdrPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForUlBasicMeas" *10 < "OlcPeriodTimerLen" /2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
This parameter is valid only when "ChoiceRprtUnitForUlBasicMeas" is set to MIN,and it must satisfy the following relationship:
"MinForUlBasicMeas" * 60 < "LdrPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForUlBasicMeas" * 60000 < "OlcPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
None
None
This parameter is valid only when "ChoiceRprtUnitForDlBasicMeas" is set to TEN_MSEC,and it must satisfy the following relat
"TenMsecForDlBasicMeas" *10 < "IntraFreqLdbPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPE
"TenMsecForDlBasicMeas" *10 < "PucPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForDlBasicMeas" *10 < "LdrPeriodTimerLen" * 1000/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"TenMsecForDlBasicMeas" *10 < "OlcPeriodTimerLen"/2 (See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
This parameter is valid only when "ChoiceRprtUnitForDlBasicMeas" is set to MIN,and it must satisfy the following relationship:
"MinForDlBasicMeas" * 60 < "IntraFreqLdbPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60 < "PucPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60 < "LdrPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD");
"MinForDlBasicMeas" * 60000 < "OlcPeriodTimerLen"/2(See "SET ULDCPERIOD" and "SET USATLDCPERIOD").
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForHsdpaPwrMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForHsdpaPwrMeas" is set to MIN.

None
None
This parameter is valid only when "ChoiceRprtUnitForHsdpaRateMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForHsdpaRateMeas" is set to MIN.
None
None
None
None
This parameter is valid only when "ChoiceRprtUnitForUlOlcMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForUlOlcMeas" is set to MIN.
None
None
None
This parameter is valid only when "ChoiceRprtUnitForDlOlcMeas" is set to TEN_MSEC.
This parameter is valid only when "ChoiceRprtUnitForDlOlcMeas" is set to MIN.
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid only when "Slot Format" is equal to or more than D8.
None
None
None
None
This parameter forms an SPI mapping table with "UserPriority", "THPClass", and "SPI".
This parameter forms an SPI mapping table with "TrafficClass", "THPClass", and "SPI".
This parameter forms an SPI mapping table with "TrafficClass", "UserPriority", and "THPClass".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is valid when the value of "Location Working Mode" is SAS_CENTRIC or SAS_CENTRIC_PREFERRED
This parameter is valid only when "LcsWorkMode" is set to RNC_CENTRIC and the location result is calculated by the RNC b
None
The SMLC parameters of the cell identified by this parameter must have been configured through "ADD USMLCCELL".
None
None
None
This parameter is valid when the "CellLocCfgType" is set to BOTH or CELL_ANTENNA.

This parameter is valid when the "CellLocCfgType" is set to BOTH or CELL_CENTER.

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"SqiGoodThres" > "SqiBadThres"
"SqiGoodThres" > "SqiBadThres"
None
This parameter is valid only when "SRNSR_DSCR_PROPG_DELAY_SWITCH" of "SrnsrSwitch" in "SET UCORRMALGOSWI
This parameter is valid only when "SRNSR_DSCR_IUR_RESRCE_SWITCH" of "SrnsrSwitch" in "SET UCORRMALGOSWITC
This parameter is valid only when "SRNSR_DSCR_SEPRAT_DUR_SWITCH" of "SrnsrSwitch" in "SET UCORRMALGOSWIT
This parameter is valid only when "SRNSR_DSCR_SEPRAT_DUR_SWITCH" of "SrnsrSwitch" in "SET UCORRMALGOSWIT
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
This parameter must not be set to CS_DOMAIN when the "TrafficClass" parameter is set to INTERACTIVE or BACKGROUND
There must be one parameter set to 15, this parameter or the parameter "BetaD".
There must be one parameter set to 15, this parameter or the parameter "BetaC".
This parameter is valid when HO_INTER_RAT_RNC_SERVICE_HO_SWITCH under the "HoSwitch" parameter is set to on th
UCORRMALGOSWITCH" command.
None
None
None
None
None
None
The value of this parameter must be larger than the value of the "Event4bThd" parameter.
The value of this parameter must be smaller than the value of the "Event4aThd" parameter.
None
None
None
None
None
None
None
None
None
None
None
None
This parameter is required when the "TrchType" parameter is set to TRCH_HSDSCH but not required when the "TrchType" pa
TRCH_EDCH_2MS or TRCH_EDCH_10MS.
This parameter is associated with the setting of the "HsdschMacdPduSizeNum" parameter. It is required when the "HsdschMa
to a value within the range from D1 to D8.
to D8.
This parameter is required when the "MachsDiscardTimeOpt" parameter is set to TRUE.

This parameter is required when the "TrchType" parameter is set to TRCH_EDCH_2MS or TRCH_EDCH_10MS but not requir
parameter is set to TRCH_HSDSCH.
This parameter is associated with the setting of the "EdchMacdPduSizeNum" parameter. It is required when the "EdchMacdPd
value within the range from D1 to D12.
D12.
None
None
None.
None.
None.
None
The value of this parameter cannot be smaller than the value of the "MinSirtarget" parameter. In addition, the value of this para
value of the "MaxSirtarget" parameter.
None
None
None
None
This parameter is required when the "RefEtfciNum" parameter is set to a value within the range of D1 to D8.
This parameter is required when the "RefEtfciNum" parameter is set to D7 or D8.
This parameter is required when the "RefEtfciNum" parameter is set to D8.


This parameter can not be less than "ERgch3IndStpThs" parameter.
This parameter should be less than "ERgch2IndStpThs" parameter.
None
None
The value of this parameter must be less than or equal to the value of "HarqPOLitRetrLRate".
The value of this parameter must be greater than or equal to both the value of "HarqPOLitRetrHRate" and the value of "HarqP
None
None
None
None
This parameter is required when the "TrchType" parameter is set to TRCH_DCH. The setting of the "SirAdjustStep" parameter
parameter. Assume that this parameter is changed from BLERquality1 to BLERquality2 and "SirAdjustStep" is changed from S
Then, these values must fulfill the following condition: (1- BLERquality1) x SirAdjustStep1 / BLERquality1 = (1 - BLERquality2)
This parameter is required when "TrchType" is set to TRCH_EDCH_2MS or TRCH_EDCH_10MS.
This parameter is required when "TrchType" is set to TRCH_EDCH_2MS or TRCH_EDCH_10MS.

1. The value of this parameter must be smaller than that of "MaxEdchRetransNum".
2. The value of this parameter must be smaller than that of "EdchTargetLargeRetransNum".
1. If "TrchType" is set to TRCH_EDCH_2MS or TRCH_EDCH_10MS, this parameter is required and must be set to a value sm
"MaxEdchRetransNum".
2. The value of this parameter must be greater than that of "EdchTargetLittleRetransNum".
None
"UlThd6A1" <= "UlThd6B1".
"UlThd6A2" <= "UlThd6B2";

"UlThd6A2" > "UlThd6B1".
"UlThd6A1" <= "UlThd6B1";

"UlThd6A2" > "UlThd6B1".
"UlThd6A2" <= "UlThd6B2".
"StaBlkNum5A" >= "Thd5A".

"StaBlkNum5A" >= "Thd5A".
None
"ThdEa" <= "ThdEb".
"ThdEa" <= "ThdEb".
None
None
None
None
None
None
This parameter is required when the "RlcMode" parameter is set to AM.
This parameter is required when the "RlcMode" parameter is set to AM and the "AmRlcCfgPara" parameter is set to SENDER_
parameter for RAB cannot be smaller than the value of the "TxWindowSizeLimit" parameter.
parameter cannot be larger than the value of the "TxWindowSize" parameter.
This parameter is required when the "RlcMode" parameter is set to UM or TM.
This parameter is required when the "AMRlcDiscardMode" parameter is set to TIMER_BASED_WITH_EXPLICIT_SIGNALLIN

This parameter is required when the "RlcMode" parameter is set to UM or TM and the "UMTMRlcDiscardMode" parameter is s
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING.
This parameter is required when the "AMRlcDiscardMode" parameter is set to DISCARD_AFTER_MAX_DAT_RETRANSMISS

This parameter is required when the "AMRlcDiscardMode" parameter is set to NO_DISCARD.
This parameter is required when the "RlcMode" parameter is set to AM and the "AmRlcCfgPara" parameter is set to RECEIVE
parameter for RAB cannot be smaller than the value of the "RxWindowSizeLimit" parameter.
parameter cannot be larger than the value of the "RxWindowSize" parameter.
This parameter is required when the "RlcMode" parameter is set to AM, the "AmRlcCfgPara" parameter is set to SENDER_PA
parameter is set to TRUE.
None
None
This parameter is required when the "RlcMode" parameter is set to AM and "AmRlcCfgPara" to FLOWCONTROL_PARA.
None.
None.
None.
None.
None
The value of this parameter cannot be smaller than the value of the "MinSirtarget" parameter. In addition, the value of this para
value of the "MaxSirtarget" parameter.
None.
None.
None
None

The value of this parameter must be greater than or equal to that of "ERgch3IndStpThs".
The value of this parameter must be smaller than or equal to that of "ERgch2IndStpThs".
None
None
The value of this parameter must be greater than or equal to both the value of "HarqPOLitRetrHRate" and the value of "HarqP
None.
None
None.
None.
None.
None
This parameter is required when the "RlcMode" parameter is set to AM.
This parameter is required when the "RlcMode" parameter is set to AM and the "AmRlcCfgPara" parameter is set to EDIT_SE
This parameter is required when the "RlcMode" parameter is set to UM.

This parameter is required when the "RlcMode" parameter is set to UM and the "UMTMRlcDiscardMode" parameter is set to
TIMER_BASED_WITHOUT_EXPLICIT_SIGNALLING.
This parameter is required when the "AMRlcDiscardMode" parameter is set to NO_DISCARD.
This parameter is required when the "RlcMode" parameter is set to AM and the "AmRlcCfgPara" parameter is set to EDIT_RE
This parameter is required when the "RlcMode" parameter is set to AM, the "AmRlcCfgPara" parameter is set to EDIT_SENDE
"CfgPollingPara" parameter is set to TRUE.
None
None
None
None
None
None
None
None
None
None
"D2F2PTvmThd" < "F2DTvmThd";

"D2F2PTvmThd" < "BeEFach2DTvmThd".
None
None
None
None
"D2F2PTvmThd" < "F2DTvmThd".
None
"BeH2FTvmThd" < "BeF2HTvmThd";

"BeH2FTvmThd" < "BeEFach2HTvmThd";
"BeH2FTvmThd" < "BeEFach2CpcTvmThd";
"BeH2FTvmThd" < "BeF2CpcTvmThd".
None
None
"BeH2FTvmThd" < "BeF2HTvmThd".
None
"RtDH2FTvmThd" < "RtF2DHTvmThd";

"RtDH2FTvmThd" < "RtEFach2DHTvmThd";
"RtDH2FTvmThd" < "RtEFach2CpcTvmThd";
"RtDH2FTvmThd" < "RtF2CpcTvmThd".
None
None
"RtDH2FTvmThd" < "RtF2DHTvmThd".
None
None
None
None
None
None
None
"BeH2FTvmThd" < "BeF2CpcTvmThd".
None
"RtDH2FTvmThd" < "RtF2CpcTvmThd".
None
None
None
"D2F2PTvmThd" < "BeEFach2DTvmThd".
None
"BeH2FTvmThd" < "BeEFach2HTvmThd".
None
"RtDH2FTvmThd" < "RtEFach2DHTvmThd".
None
"BeH2FTvmThd" < "BeEFach2CpcTvmThd".
None
"RtDH2FTvmThd" < "RtEFach2CpcTvmThd".
None
"D2F2PTvmThd" < "FastDormancyF2DHTvmThd";
"RtDH2FTvmThd" < "FastDormancyF2DHTvmThd";
"BeH2FTvmThd" < "FastDormancyF2DHTvmThd".
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
"UlGBR" of GOLD users ("UserPriority" is set to GOLD) >= "UlGBR" of SILVER users ("UserPriority" is set to SILVER) >= "UlG
"DlGBR" of GOLD users ("UserPriority" is set to GOLD) >= "DlGBR" of SILVER users ("UserPriority" is set to SILVER) >= "DlG
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Access Service Interrupted After Modification Interruption Scope
Read & Write No (No impact on the UE in idle mode) Not involved
Read & Write Not involved Not involved
Read & Write Yes AAL2 path


Read only Not involved Not involved

Read only No (No impact on the UE in idle mode) Not involved
Read Only Not involved Not involved



Read & Write Yes BSC6900
Read & Write Yes Optical port
Read & Write Yes E1/T1 port

Read & Write Yes E1/T1 port

Read & Write Yes Ethernet port
Read & Write No (Impact on the UE in idle mode) Not involved
Read Only No (No impact on the UE in idle mode) Not involved










Read & Write Yes IP path
















Read & Write Yes PPP link




Read & Write Yes SAAL link

Read & Write Yes SCTP link








Read & Write Yes Cell




Read only Yes Cell
























Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell

Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell

Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell
Read only Yes Cell

Read only Yes Cell
Read only Yes Cell






















Interruption Duration(Min) Caution Validation of Modification
The parameter modification has
Not involved None no impact on the equipment.
The parameter cannot be

Not involved modified. Not involved


Less than 5 minutes None no impact on the equipment.



Less than 5 minutes The UNI link must be available. no impact on the equipment.

Less than 5 minutes The IMA group must be available. no impact on the equipment.
The FRAATM link must be The parameter modification has

Less than 5 minutes available. no impact on the equipment.

Less than 5 minutes The port must be available. no impact on the equipment.
The ATM logic port after the The parameter modification has
Less than 5 minutes modification must be available. no impact on the equipment.
Not involved The resource group must exist. no impact on the equipment.
The configuration data must be the The parameter modification has

Less than 5 minutes same as that of the peer system. no impact on the equipment.
The configuration data must be the The parameter modification has

Less than 5 minutes same as that of the peer system. no impact on the equipment.


Not involved None Not involved
The TRM load threshold must be The parameter modification has

Not involved configured already. no impact on the equipment.



Modified according to practical The parameter modification has

Not involved networking. no impact on the equipment.
The modification of the timer
involves the peer end. For details,
see ITU-T Q2630.1 or ITU-T The parameter modification has
Not involved Q2630.2. no impact on the equipment.






Not involved The TRMMAP must be configured. no impact on the equipment.

The FACTORTABLE must be The parameter modification has

Not involved configured. no impact on the equipment.
The load EQ table is configured The parameter modification has

Not involved already. no impact on the equipment.







When the parameter is set to CS1,

it indicates that the local RNC is
interconnected to the adjacent
node by using the CS1 protocol
version. When the parameter is set
to CS2, it indicates that the local
RNC is interconnected to the
adjacent node by using the CS2
protocol version. The CS2 protocol
version is backward compatible
with the CS1. By default, the
parameter is set to CS2. When the
peer is not compatible with the
local CS2 messages (the peer
does not process the compatible
domain according to protocol
requirements), the protocol version The parameter modification has
Not involved is set to CS1. no impact on the equipment.
To disable the alarm blink filter

function, set this parameter to "0".
To enable the alarm blink filter
function, set this parameter to a
value greater than 0 and turn on
the alarm blink filter switch. See
"SET ALMBLKSW" for setting the The parameter modification has
Not involved alarm blink filter switch. no impact on the equipment.
1. If you set "Upper count
threshold of raised fault" and
"Lower count threshold of raised
fault" to "0", the accumulated
number of blink times for the alarm
is counted but not reported.
2. If "Upper count threshold of
raised fault" is not "0", the value of
fault" cannot be "0" and you must
ensure that "Upper count threshold
of raised fault" is greater than
fault".
3. When "Upper count threshold of
raised fault" is not "0" and "Alarm
switch of blinking filter" and
"Switch of stat blinking alarm" are
"ENABLE", you cannot set "Alarm
blink threshold" to "0". Otherwise,
blink statistics of the alarm is not The parameter modification has
Not involved performed. no impact on the equipment.
1. If you set "Upper count

threshold of raised fault" and
fault" to "0", the accumulated
number of blink times for the alarm
2. If "Lower count threshold of
raised fault" is not 0, the value of
"Upper count threshold of raised
fault" cannot be 0 and you must
ensure that "Lower count threshold
of raised fault" is smaller than
"Upper count threshold of raised
fault".
3. When "Upper count threshold of
1. If you set "Upper time threshold
of raised fault" and "Lower time
threshold of raised fault" to "0", the
accumulated alarm blink duration
2. If "Upper time threshold of
"Lower time threshold of raised
ensure that "Upper time threshold
of raised fault" is greater than
fault".
3. When "Upper time threshold of
1. If you set "Upper time threshold

of raised fault" and "Lower time
threshold of raised fault" to "0", the
accumulated alarm blink duration
2. If "Upper time threshold of
ensure that "Lower time threshold
of raised fault" is smaller than or
equal to "Upper time threshold of
raised fault".
3. When "Lower time threshold of
To enable the alarm blink filter
function, set "Alarm switch of
blinking filter" and "Switch of stat The parameter modification has
Not involved blinking alarm" to "ENABLE". no impact on the equipment.




flow control function can be
affected if this parameter is The parameter modification has
Not involved modified. no impact on the equipment.
Flow control function can be
affected if this parameter is The parameter modification has











Not involved Not involved Not involved






If the interface board clock source

of the MPS subrack is set, you can
set the 8 kHz output clock source.
For the MPS and TCS, you can
set the backplane board 8k output
clock as the clock source of the
interface board. For the EPS, you The parameter modification has
Not involved cannot perform the setting. no impact on the equipment.

Each backplane board 8K clock

has only one clock source. You
are not allowed to turn on the
same backplane board 8K clock
switch for multiple interface The parameter modification has
Not involved boards. no impact on the equipment.
Each backplane board 8K clock

has only one clock source. You
are not allowed to turn on the
same backplane board 8K clock
switch for multiple interface The parameter modification has
Not involved boards. no impact on the equipment.
Clock sources and priorities are in The parameter modification has
Not involved one-to-one mapping. no impact on the equipment.
Clock sources and priorities are in The parameter modification has
Not involved one-to-one mapping. no impact on the equipment.
Clock sources and priorities are in

one-to-one mapping. Each
backplane board 8K clock has only The parameter modification has
Not involved one clock source. no impact on the equipment.
If you want to modify the value of
"Clock board type" from "GCGa" to The board should be reset to
"GCUa", the board must not be validate the parameter
Less than 10 minutes configured with GPS. modification.
1. This command is applicable to
the boards AOUa and POUa.
2. It is used for interworking with The parameter modification has
Not involved products of other manufacturers. no impact on the equipment.
It is used for interworking with The parameter modification has
the boards AOUa, POUa, AOUc,
POUc, and OIUa.
If the mode is not consistent, will The setting of this parameter must
interrupt service until it is be negotiated with that on the The parameter modification has
consistent. interconnected side. no impact on the equipment.




If the mode is not set back, will The parameter modification has
interrupt service until it is set back. None no impact on the equipment.


If the MTU configuration fails to
meet the requirement of the The interconnection may be
network, the services will be affected if this parameter is The parameter modification has
adversely affected. modified. no impact on the equipment.
Not involved None
The existing networking can be no impact on the equipment.
affected when the relation
between the VLAN and the DSCP The parameter modification has
Not involved are
Thereset.
existing networking can be no impact on the equipment.
Not involved are reset. no impact on the equipment.
If certain link is occupied,
conversion from E1 to T1 or from The parameter modification has
Not involved T1 to E1 cannot be performed. no impact on the equipment.

The conversion from E1 to T1 or

from T1 to E1 takes effect after the The parameter modification has
Less than 5 minutes board is reset. no impact on the equipment.
The frame structure must be

Interrupt the service until negotiate consistent with that on the The parameter modification has
successfully again. interconnected side. no impact on the equipment.


The line code must be consistent

with that on the interconnected
side. HDB3 (HDB3 code) and AMI
(AMI code) are used for E1 ports.
Interrupt the service until negotiate B8ZS (B8ZS code) and AMI_ZCS The parameter modification has
successfully again. (AMI code) are used for T1 ports. no impact on the equipment.
The setting of DIP switches must
Interrupt the service until negotiate be consistent with that on the The parameter modification has
This parameter is valid only in the The parameter modification has
Not involved E1 mode of the AEUa. no impact on the equipment.
1. When the peer end

unconditionally changes the bits in
the check message, the services
are disrupted if the switch is set to
ON.
When the peer end unconditionally 2. When the switch is set to OFF,
changes the bits in the check the alarm "Inconsistent
message, the services will not Configurations at the Two Ends of
resume unless the switch is set to the Link over the Ater Interface" The parameter modification has
OFF. will not be reported. no impact on the equipment.
If certain link is occupied,
conversion from E1 to T1 or from The parameter modification has
Not involved T1 to E1 cannot be performed. no impact on the equipment.

If this parameter is set to

REMOTE_LOOP and
LOCAL_LOOP, the service on this
link is affected until the loopback is
cancelled.
When the upper layer bearer is
IMAGRP, IMAGRP is reset after
the loopback is canceled.
Otherwise, the state of the
IMAGRP is abnormal and upper
The loopback keeps interrupting layer service cannot be The parameter modification has
the services until it is cancelled. established. no impact on the equipment.








The port can be set to the DOWN

or UP state when this parameter is
modified. If the negotiation modes
on the local and peer end are not
Interrupt the service until negotiate consistent, the service can be The parameter modification has
successfully again. interrupted. no impact on the equipment.
The port can be set to the DOWN

or UP state when this parameter is
modified. If the speed modes on
the local and peer end are not
Interrupt the service until negotiate consistent, the service can be The parameter modification has
successfully again. interrupted. no impact on the equipment.
If the mode is not consistent, will The interconnection may be
interrupt service until it is affected if this parameter is The parameter modification has
consistent. modified. no impact on the equipment.
If the value is too big, will interrupt If this parameter is set to a larger
service until it is set to the normal value, the bandwidth of the service The parameter modification has
value. is smaller. no impact on the equipment.


If this threshold is set to a too
small value, the Ethernet Port
Broadcast Packets Exceeding
alarm (alarm ID: 21387) may be The parameter modification has
Not involved generated. no impact on the equipment.
The setting of this parameter at
the local end must be consistent
with that at the peer end.
Otherwise, the CFM function is The parameter modification has
Not involved unavailable. no impact on the equipment.
Less than 5 minutes. None no impact on the equipment.
The setting of this parameter at
the local end must be consistent
with that at the peer end.
Otherwise, the CFM function is The parameter modification has
Not involved unavailable. no impact on the equipment.





















This parameter determines
whether to load data from the
OMU or the FLASH when the RNC
or the board is restarted. The The parameter modification has
Not involved equipment is affected. no impact on the equipment.







IMA ID identifies an IMA group.

Normally, in the same interface
board, IMA ID must be unique. To
avoid using the same IMA ID
allocated on the peer NodeB, use
different IMA ID on the RNC side The parameter modification has
Not involved and the NodeB. no impact on the equipment.

If the line delay is great and the
maximum delay is too small, The parameter modification has
Not involved certain links cannot be activated. no impact on the equipment.
The IMA protocol version must be The parameter modification has

Not involved consistent with that on the peer. no impact on the equipment.


Not involved modified.
The parameter cannot be Not involved













The adjacent node ID must be The parameter modification has
The parameter IPPATH must be The parameter modification has
Not involved configured in advance. no impact on the equipment.




The services will be interrupted if

the setting of this parameter is
inconsistent with the setting at the The parameter modification has
peer end. None no impact on the equipment.
If the value is not consistent, will

interrupt service until it is The parameter modification has
consistent. None no impact on the equipment.












Not involved The resource group must exist. no impact on the equipment.

Incorrect setting of this parameter

If the mode is not set back, will can lead to access failure to the The parameter modification has
interrupt service until it is set back. target IP address. no impact on the equipment.

The address must exist and The parameter modification has
Not involved respond to the PING request. no impact on the equipment.
When the network status is poor,
the check period should not be too
small. Otherwise, the path state is The parameter modification has
Not involved affected. no impact on the equipment.
the check count should not be too
small. Otherwise, the path state is The parameter modification has
Not involved affected. no impact on the equipment.
the packet length should not be
too large. Otherwise, the path The parameter modification has
Not involved state is affected. no impact on the equipment.










Not Involved None no impact on the equipment.


If the parameter is modified, the
admission rule of subsequent new
access services are affected (Path The parameter modification has
Not involved type selection sequence). no impact on the equipment.



The routing context must be
The services are interrupted until unique and needs to be negotiated The parameter modification has
the M3DE is available. with the peer. no impact on the equipment.


The routing context must be
The services are interrupted until unique and needs to be negotiated The parameter modification has
the M3DE is available. with the peer. no impact on the equipment.

The mask is calculated according

to the link set to a destination The parameter modification has
Not involved entity. no impact on the equipment.






The routing priority is modified. In
the case of multiple routes to the
same signaling point, the route The parameter modification has
Not involved priority is affected. no impact on the equipment.





The local IP address and peer IP
must be configured in the same
network segment. The peer IP
address cannot be the same with The parameter modification has
Not involved the local IP address of the RNC. no impact on the equipment.

The local IP address and peer IP

must be configured in the same
network segment. The peer IP
address cannot be the same with The parameter modification has
Not involved the local IP address of the RNC. no impact on the equipment.

No_HC: disable the header
compression function;
RTP/UDP/IP_HC: enable the The parameter modification has
Not involved RTP/UDP/IP/PPP function no impact on the equipment.
No_HC: disable the header

compression function;
RTP/UDP/IP_HC: enable the The parameter modification has
Not involved RTP/UDP/IP/PPP function no impact on the equipment.
Interrupt the service until negotiate Negotiation fails if this parameter The parameter modification has
successfully again. is modified. no impact on the equipment.

ENABLE: the multiplexing frame

function of the PPP link is enabled.
DISABLE: the multiplexing frame
function of the PPP link is The parameter modification has
Not involved disabled. no impact on the equipment.
If the PPP frame length is larger

than this value, PPPMUX
multiplexing cannot be performed.
The value of this parameter cannot
be larger than the maximum
multiplexing frame length wMuxMfl
and the number sub-frame must
be larger than 2 as the enabling
condition of PPPMUX (the relation
between the maximum sub-frame
length and the maximum
multiplexing frame length is: The parameter modification has
Not involved MuxMaxSfL<=(wMuxMfl-8)/2 ). no impact on the equipment.

be smaller than the maximum
PPPMUX sub-frame length. The
number sub-frame must be larger The parameter modification has
Not involved than 2 to enable the PPPMUX. no impact on the equipment.
Negotiation can succeed only
when the configuration is
consistent on the local and peer The parameter modification has
Not involved ends. no impact on the equipment.
Interrupt the service until negotiate consistent on the local and peer The parameter modification has
successfully again. ends. no impact on the equipment.



If the PPP frame length is larger

than this value, PPPMUX
multiplexing cannot be performed.
be larger than the maximum
multiplexing frame length wMuxMfl
and the number sub-frame must
be larger than 2 as the enabling
condition of PPPMUX (the relation
between the maximum sub-frame
length and the maximum
multiplexing frame length is: The parameter modification has
Not involved MuxMaxSfL<=(wMuxMfl-8)/2 ). no impact on the equipment.
be smaller than the maximum
PPPMUX sub-frame length. The
number sub-frame must be larger The parameter modification has
Not involved than 2 to enable the PPPMUX. no impact on the equipment.







Interrupt the service until negotiate The parameter modification has
successfully again. None no impact on the equipment.

The setting of this parameter must
Interrupt the service until negotiate be negotiated with that on the The parameter modification has


According to the MTP3 load

sharing principle, the link selection
mask must be set properly. If the
value is not set properly, the load
sharing between MTP3 links may The parameter modification has
Not involved fail. no impact on the equipment.
For the modification of the The parameter modification has
Not involved parameter, See the ITU-T Q704. no impact on the equipment.





The routing priority is modified. In
the case of multiple routes to the
same signaling point, the route The parameter modification has
Not involved priority is affected. no impact on the equipment.


The modified parameter takes The parameter modification has

Not involved effect after the RNC is reset. no impact on the equipment.

The parameter modification has no The parameter modification has
Not involved impact on the equipment. no impact on the equipment.



The services are interrupted until The parameter modification has
the signaling point is available. None no impact on the equipment.

the signaling point is available. None no impact on the equipment.
The switch is off in the case of a

signaling point to the single link.
After the link to a signaling point is
disconnected, the restart
The services are interrupted until procedure is performed. See the The parameter modification has
the signaling point is available. ITU-T Q704. no impact on the equipment.
This parameter cannot be

successfully again. peer. no impact on the equipment.

interrupt service until it is be consistent with that on the The parameter modification has
consistent. peer. no impact on the equipment.




If the mode is not consistent, will If the mode is not consistent, will
interrupt service until it is interrupt service until it is The parameter modification has
consistent. consistent. no impact on the equipment.
When the loopback type is
changed to REMOTE_LOOP or
LOCAL_LOOP, the service is
affected. The service becomes
normal when the loopback test is
canceled. When the loopback type
is set to LOCAL_LOOP, you
cannot directly change it to
REMOTE_LOOP. You must
change it to NO_LOOP first and
then to REMOTE_LOOP. You can
change the loopback type from
REMOTE_LOOP to The parameter modification has
Not involved LOCAL_LOOP in the similar way. no impact on the equipment.
When the loopback type is

changed to REMOTE_LOOP or
LOCAL_LOOP, the service is
affected. The service becomes
normal when the loopback test is
canceled. When the loopback type
is set to LOCAL_LOOP, you
cannot directly change it to
REMOTE_LOOP. You must
change it to NO_LOOP first and
then to REMOTE_LOOP. You can
change the loopback type from
The loopback keeps interrupting REMOTE_LOOP to The parameter modification has
the services until it is cancelled. LOCAL_LOOP in the similar way. no impact on the equipment.


The priority of the signaling link The parameter modification has

Not involved should be the highest. no impact on the equipment.

This parameter can be added and The parameter modification has

Not involved modified. It cannot be deleted. no impact on the equipment.
This parameter can be added or The parameter modification has

Not involved modified but cannot be removed. no impact on the equipment.






















ENABLE: the multiplexing frame

function of the PPP link is enabled.
DISABLE: the multiplexing frame
function of the PPP link is The parameter modification has
Not involved disabled. no impact on the equipment.




The parameter modification does
Not involved None not impact the equipment.
The parameter modification does

Not involved None not impact the equipment.
The transmission priority of the
service is affected if the queue
DSCP value of the port is The parameter modification has
The transmission priority of the no impact on the equipment.
The transmission priority of the no impact on the equipment.
















When the bearing type is modified,
The services are interrupted until the new bearing type must be The parameter modification has
the SAAL link is working normally. configured. no impact on the equipment.
the SAAL link is working normally. None no impact on the equipment.

The services are interrupted until The configuration data must be the The parameter modification has
the SAAL link is working normally. same as that of the peer system. no impact on the equipment.
The services are interrupted until The configuration data must be the The parameter modification has
the SAAL link is working normally. same as that of the peer system. no impact on the equipment.
The corresponding traffic index The parameter modification has
Not involved must be configured. no impact on the equipment.
The corresponding traffic index The parameter modification has

Not involved must be configured. no impact on the equipment.

The modification of the
management proving status does
not affect the established SAAL
link, but affect the SAAL link The parameter modification has
Not involved establishment mode. no impact on the equipment.
The modification of the parameter
does not affect the established
SAAL link, but affect the next The parameter modification has
Not involved establishment of the SAAL link. no impact on the equipment.
affects the detection sensitivity of The parameter modification has
Not involved the SAAL link. no impact on the equipment.
affects the detection sensitivity of The parameter modification has
Not involved the SAAL link. no impact on the equipment.
Not involved parameter, see the ITU-T Q.2110. no impact on the equipment.
For details of the timer, see ITU-T
Q.714. The modification is not The parameter modification has
Not involved recommended. no impact on the equipment.
The cell should be activated after
Not involved None the parameter modification.



The local end of the SCTP link is

the server and the application type
is NBAP, the working mode should
not be modified as the client.
For the SCTP link of the M3UA
application, the working mode can
The services are interrupted until be modified only when the upper The parameter modification has
the SCTP link is working normally. layer application is deleted. no impact on the equipment.
The priority of the signaling link The parameter modification has

Not involved should be the highest. no impact on the equipment.
The parameter can be modified
The services are interrupted until when "MODE" in the command The parameter modification has
the SCTP link is working normally. "ADD SCTPLNK" is set to Client. no impact on the equipment.
The both end address of the SCTP
is the parameter for the
interconnection. The value can be
The services are interrupted until modified after the negotiation with The parameter modification has
the SCTP link is working normally. the peer system. no impact on the equipment.
The SCTP port number is the
parameter for the negotiation. The
The services are interrupted until value can be modified after the The parameter modification has
the SCTP link is working normally. negotiation with the peer system. no impact on the equipment.
It is valid when
The services are interrupted until "LOGPORTFLAG[/PARA in the The parameter modification has
the SCTP link is working normally. command "ADD SCTPLNK" is ON. no impact on the equipment.
It is valid when
The services are interrupted until "LOGPORTFLAG[/PARA in the The parameter modification has
the SCTP link is working normally. command "ADD SCTPLNK" is ON. no impact on the equipment.
The value should be smaller than
"RTOMAX" in the command "ADD The parameter modification has
Not involved SCTPLNK". no impact on the equipment.
The value should be greater than
"RTOMIN" in the command "ADD The parameter modification has
"RTOMIN" and smaller than
"RTOMAX" in the command "ADD The parameter modification has
"MAXPATHRETR" in the The parameter modification has
Not involved command "ADD SCTPLNK". no impact on the equipment.
"MAXASSOCRETR" in the The parameter modification has
The checksum mode need the
negotiation with the peer.
The services are interrupted until According to the RFC4960, the The parameter modification has
the SCTP link is working normally. value should be set to CRC32. no impact on the equipment.
The checksum mode need the
negotiation with the peer.
The services are interrupted until According to the RFC4960, the The parameter modification has
the SCTP link is working normally. value should be set to CRC32. no impact on the equipment.
the SCTP link is working normally. None no impact on the equipment.
The parameter is related to The parameter modification has

Not involved practical networking. no impact on the equipment.
"MAXPATHRETR" in the The parameter modification has
"MAXASSOCRETR" in the The parameter modification has
The parameter modification should

be negotiated with the peer end,
and the RNC should be reset after
the modification. It is
recommended that this parameter The BSC should be reset to
The services are interrupted until should not be modified when the validate the parameter
the SCTP link is working normally. system is running. modification.


Change this parameter will impact
the patch function controlled by The parameter modification has
Not involved switch 1. no impact on the equipment.








The IP address of the TGW cannot

use the configured IP address of
another TGW . The IP address of
TGW cannot be the same as the
IP address configured in the RNC.
Otherwise, operation and
maintenance channel for TGW The parameter modification has
Not involved fails. no impact on the equipment.

another TGW. The IP address of

another TGW . The IP address of
the function interrelated with The parameter modification has
Not involved Parameter 1. no impact on the equipment.


affects the adjacent node that is
configured with the factor table.
After the successful modification,
the parameter takes effect in the
following two cases:
1. New access subscriber.
2. Bandwidth modification of the The parameter modification has
Not involved existing subscriber no impact on the equipment.

















transport layer bandwidth
admission of the subsequence The parameter modification has
Not involved access service is affected. no impact on the equipment.











following two cases: 1. New
access subscriber. 2. Bandwidth
modification of the existing The parameter modification has
Not involved subscriber. no impact on the equipment.

following two cases: 1. New
access subscriber. 2. Bandwidth
modification of the existing The parameter modification has
Not involved subscriber. no impact on the equipment.























affects the adjacent node
configured with the TRMMAP.
After the successful modification, it
is valid in the case of the new
access of a subscriber and the
bandwidth modification of an The parameter modification has
Not involved existing subscriber. no impact on the equipment.


















































1. If you set the start date or end
date of DST to a day of the week
after a specific date, the specific
date must be six days or more
days prior to the last day of the
month. For example, the last day
of October is the 31st day. Then,
the specific date cannot be later
than the 25th (31-6) day. If you set
the specific date to Tuesday after
26 October, this date is not
included in the November of 2005.
Therefore, the specific date is
invalid. This date in 2006,
however, is October 31, which is
valid. As a result, you must follow
this principle to ensure that a
specific data is always valid.
2. You are not allowed to set the
start date or end date of DST to
February 29. This is because that
the local time changes between
DST and non-DST. In a non-leap
year, February 29 does not exist.
Therefore, the local time cannot
change between the start date and
the end date.
3. The start month and end month The parameter modification has
Not involved of DST cannot be the same. no impact on the equipment.

1. If you set the start date or end
date of daylight saving time (DST)
to a day of the week after a
specific date, the specific date
must be six days or more days
prior to the last day of the month.
For example, the last day of
October is the 31st day. Then, the
specific date cannot be later than
the 25th (31 – 6) day. If you set
the specific date to Tuesday after
26 October, this date is not
included in the November of 2005.
Therefore, the specific date is
invalid. This date in 2006,
however, is October 31, which is
valid. As a result, you must follow
this principle to ensure that a
specific data is always valid.
2. You are not allowed to set the
start date or end date of DST to
February 29. This is because that
the local time changes between
the start date and end date of
DST. In a non-leap year, February
29 does not exist. Therefore, the
local time cannot change between
DST and non-DST.
3. The start month and end month The parameter modification has
Not involved of DST cannot be the same. no impact on the equipment.













If the TFO/TrFO is not configured,
it is recommended that the timer
should be set to 3000ms. If the
TFO/TrFO is configured, it is
recommended that the timer
should be set to 7000 ms to
complete the adjustment of DL
Not involved AMR speech rate. Not involved

If the TFO/TrFO is not configured,
it is recommended that the timer
should be set to 3000ms. If the
TFO/TrFO is configured, it is
recommended that the timer
should be set to 7000 ms to
complete the adjustment of DL
Not involved AMR speech rate. Not involved













































Interruption until the cell is The cell should be deactivated in The cell should be activated after
activated again. advance. the parameter modification.










The cell should be deactivated in The cell should be activated after
Not involved advance. the parameter modification.










The value of this parameter can be

changed only after the cell is The cell should be activated after
1 deactivated. the parameter modification.







Not involved be changed. Not involved






















































If the value is too high, the

possibility of wrong rejection to
uplink admissions increases,
leading to waste in uplink
resources. If the value is too low,
the uplink resources is insufficient.
However, because the possibility
of putburst load by ACK/NACK
and its impact are relatively low,
the value can be set to a low level,
representing the loose admission The parameter modification has
Not involved rule. no impact on the equipment.










1. Cell ID is in one-to-one
correspondence with Service Area
Identity (SAI).
2. SAI = PLMN + LAC + SAC.
PLMN-Id (Public Land Mobile
Network - Identity) is configured
through the command "ADD
UCNOPERATOR" and LAC
(Location Area Code) is configured
UCELLSETUP". LAC of CBS is
the same as that of CS/PS. This
parameter is SAC.
3. SAC of CBS is different from
that of CS/PS because SAC of
CBS need not be configured
USAC" in advance.
4. When the CBS is active,
"CBSSAC" must not be removed
or modified.
5. The parameter modification has
Not involved no impact on the equipment. Not involved
1. Set this parameter to ON if you

want to use the RNC built-in cell
broadcast function. 2. Do not set
this parameter to ON when the
RNC is connected to the CBS
server. 3. The parameter
modification has no impact on the
Not involved equipment. Not involved
This parameter supports only
ASCII code character set.The
parameter modification has no
Not involved impact on the equipment. Not involved




































































Not Involved None the parameter modification.



The parameter modification has no







Not involved None the parameter modification.





























































































































































































































































































"SET UCHRSCOPECTRL" is run

to specify whether to allow the
output of PCHR log of a cell in this
RNC. This command can be run
for configuring only a certain cell.
For convenience, the following
values are set for this parameter:
ByRack, ByNodeBId, and
ByCellId. ByRack means
configuring all the cell in a
subrack. ByNodeBId means
configuring all the cell controlled
by a NodeB. ByCellId means
configuring a certain cell.The

1. When the parameter is set to
OFF, the CHR function is disabled.
2. The modification of this
parameter has no impact on the











When the Iu-Flex function is used,
the protocol version of each CN
node must be R5 or later.The
When "CNProtclVer" in "ADD

UCNNODE" is set to R99,
SupportCRType is
CR527_SUPPORT or
CR527_NOT_SUPPORT; when
"CNProtclVer" in "ADD
SupportCRType is
CR528_SUPPORT or
SupportCRType is
CR529_SUPPORT or
UCNNODE" is set to R6, there is
no SupportCRType.

Set TnlBearerType according to
the actual used transport type.The
Enabling this algorithm supports

the QoS differentiation but may
decrease the system throughput of
Not involved the cell. Not involved










If the value of the parameter is set

to 0, channel retry cannot be
Not involved performed. Not involved

T302 broadcast in the SIB1 =

Roundup {[timer 302 [ms]] + 2 x
[Iub transmission delay]}. [timer
302 [ms]] is configured through the
"SET UCONNMODETIMER"
command. [Iub transmission delay]
is the Iub transmission delay
configured through the "ADD
UNodeB" command. Roundup
means rounding up and mapping
to a value of the set {100, 200,
400, 600, 800, 1000, 1200, 1400,
1600, 1800, 2000, 3000, 4000,
6000, 8000 ms}.The parameter

The time value of T314 and T315
should be both equal to 0 or both
greater than T302*N302.The
The time value of T314 and T315
should be both equal to 0 or both
greater than T302*N302.The









Before enabling load sharing, you
need to set the
"RNC_SHARE_SWITCH" switch in
"SET URRCTRLSWITCH" to
ON.The parameter modification
Not involved has no impact on the equipment. Not involved






























Before this switch is on, ensure
that related configurations are
already set for the relations among
the inter-frequency neighboring
cells. That is, identify the target
cells that support the
measurement-based DRD. If this
switch is on when no
configurations are set, the DRD
cannot be performed. Therefore,
do ensure that proper
configurations are set before The parameter modification has
Not involved enabling the switch. no impact on the equipment.

































The cell should be deactivated in The cell should be activated after
Not involved advance. the parameter modification.


















































The value of this parameter can be

Interruption until the cell is changed only after the cell is The cell should be activated after
activated again. deactivated. the parameter modification.





The cell must be removed before

the value of this parameter is
changed. The cell needs to be re-
established after the value is
changed. In this process, services
are interrupted. None Not involved



The channel must be removed

before the value of this parameter
is changed. The channel needs to
be re-established after the value is
changed. In this process, services The parameter modification has no
are interrupted. impact on the equipment. Not involved


changed. In this process, services The parameter modification has
are interrupted. None no impact on the equipment.










be re-established after the value is Changing the value of this
changed. In this process, services parameter has no impact on
are interrupted. equipment. Not involved


be re-established after the value is Changing the value of this
changed. In this process, services parameter has no impact on
are interrupted. equipment. Not involved

changed. In this process, services The value of this parameter cannot
are interrupted. be changed. Not involved
All the switches have multiple

choices. SELECT ALL means
turning on all the switches; CLEAR
ALL means turning off all the
switches; GRAYED ALL means
keeping the original states of all
the switches. The parameter
equipment. When the parameter
RNCAP_IMSI_HO_SWITCH is set
to 1, the
SNA_RESTRICTION_SWITCH
check box under the Handover
algorithm switch parameter in the
MML command "SET
UCORRMALGOSWITCH" cannot
Not involved be selected at the same time. Not involved




































































































































































The value of RafcTmr can be

negotiated with the value of
"RatcTmr" in "SET
UIUTIMERANDNUM"; thus, the
RNC can successfully initiate the
reset before the CN reset
response timer expires.The
The value of RatcTmr can be

negotiated with the value of
"RafcTmr" in "SET
UIUTIMERANDNUM"; thus, the
CN can successfully initiate the
reset before the RNC reset
response timer expires.The
The parameter value of IgorTmr

must be less than the value of
"IntrTmr" set in "SET
UIUTIMERANDNUM".The
The parameter value of IntrTmr
must be greater than the value of
"IgorTmr" set in "SET
UIUTIMERANDNUM".The
parameter modific
ation has no impact on the


Not involved the switches. Not involved

































This parameter is used with the

"ADD UMBMSALARMSERVICE"
command to enable the no MBMS
data check. If the "ADD
UMBMSALARMSERVICE"
specified service has no data on
the Iu interface within the period
specified by this parameter, an
alarm is reported.The parameter













































After being configured, this
Not involved parameter cannot be modified. Not involved
Before modifying the NodeB to a
version of R4 or earlier, deactivate
the HSUPA and HSDPA functions
of this NodeB. Before modifying
the NodeB to a version of R5 or
earlier, deactivate the MBMS
function of the NodeB.Before
modifying the NodeB to a version
of R6 or earlier, deactivate the The parameter modification has
Not involved EFACH function of the NodeB. no impact on the equipment.









The NodeB must be configured
with the electronic serial number The parameter modification has
Not involved during modification. no impact on the equipment.
The first byte of the IP address of

the FE port in the NodeB cannot
use 0 or 127. The IP address
cannot be a broadcast address or
a multicast address. The IP
address of the FE port in the
NodeB and the intranet IP address
of OMU cannot be in the network
segment or related. The IP
NodeB cannot be the same as the The parameter modification has
Not involved configured IP address in the RNC. no impact on the equipment.
The first byte of the IP address of
the FE port in the NodeB cannot
use 0 or 127. The IP address
cannot be a broadcast address or
a multicast address. The IP
NodeB and the intranet IP address
of OMU cannot be in the network
segment or related. The IP
NodeB cannot be the same as the The parameter modification has
Not involved configured IP address in the RNC. no impact on the equipment.

The IP address of the NodeB

cannot use the configured IP
address of another NodeB. The IP
address of NodeB cannot be the
same as the IP address configured
in the RNC. Otherwise, operation The parameter modification has
Not involved and maintenance channel fails. no impact on the equipment.


If the transmission type of Node is

IUB-ATM, [next hop IP address]
must be the peer IP address of the
configured IPOA PVC. If the
transmission type of Node is IUB-
IP, [next hop IP address] must be
set as follows: the peer IP address
of the PPP link, the peer IP
address of the MP group, and the
IP address in same network The parameter modification has
Not involved segment as the FE/GE port. no impact on the equipment.

IUB-IP, [next hop IP address] must
be set as follows: the peer IP
address of the PPP link, the peer
IP address of the MP group, and
the IP address in same network The parameter modification has
Not involved segment as the FE/GE port. no impact on the equipment.
must be the peer IP address of the The parameter modification has
Not involved configured IPOA PVC. no impact on the equipment.
Not involved configured IPoA PVC. no impact on the equipment.
Not involved configured IPOA PVC. no impact on the equipment.
Not involved configured IPoA PVC. no impact on the equipment.

interrupt service until it is set back. target IP address.
The existing networking can be no impact on the equipment.
Not involved are reset. no impact on the equipment.

















Set TnlBearerType according to

the actual used transport type.The





The parameter can not be The parameter modification has





UCNNODE" is set to R5 or any
later version, CsNriCfgMode may
be set to SUPP_IUFLEX.The
impact on the equipment.
later version, CsNriCfgMode may
be set to SUPP_MOCN or
SUPP_IUFLEX_MOCN.The
later version, PsNriCfgMode may
be set to SUPP_IUFLEX.The
impact on the equipment.
later version, PsNriCfgMode may
be set to SUPP_MOCN or
When the value of
"CsNriCfgMode" in "SET
UOPERATORCFGPARA" is set to
ON, or the value of
"PsNriCfgMode" in "SET
SUPP_IUFLEX, SUPP_MOCN or
SUPP_IUFLEX_MOCN, the
settings of NNSfTmr is valid.The
The settings of CSNRILength is

valid only when the value of
The settings of PSNRILength is

When the value of
SUPP_IUFLEX or
SUPP_IUFLEX_MOCN, or the
value of "PsNriCfgMode" in "SET
SUPP_IUFLEX or
SUPP_IUFLEX_MOCN, NullNRI
must be configured.The parameter
The settings of CsInfoUpdFlag is
SUPP_IUFLEX or
The settings of PsInfoUpdFlag is

SUPP_IUFLEX or
The settings of CsInfoUpdTmr is

"CsInfoUpdFlag" in "SET
The settings of PsInfoUpdTmr is

"PsInfoUpdFlag" in "SET
If the RAN Sharing Support and

MOCN Support are both switched
off,Redundant operators should be
removed by "RMV
UCNOPERATOR" and only one
Not involved operator can exist. Not involved
If the RAN Sharing Support and

MOCN Support are both switched
off,Redundant operators should be
removed by "RMV
UCNOPERATOR" and only one
Not involved operator can exist. Not involved
If the Intra RAT Inter Plmn Ho

Allowed is switched off,Neighbor
cells belonging to different PLMNs
in the intra RAT should be
Not involved removed. Not involved
If the Inter RAT Inter Plmn Ho
Allowed is switched off,Neighbor
cells belonging to different PLMNs
in the inter RAT should be
Not involved removed. Not involved











































































































None None Not involved


















The RNC should be reset to
After modification, the RNC should validate the parameter
Not involved be reset. modification.
The RNC should be reset to

The services are interrupted until After modification, the RNC should validate the parameter
the signaling point is available. be reset. modification.
After running the "ADD

UCBSADDR" command to add the
CBS server address, you should
not set this parameter to ON; After
setting this parameter to ON, you
should not run the "ADD
UCBSADDR" command to add the
CBS server address. The RNC
built-in CBS function is available
when this parameter is set to ON.
When using this function, set the
main control CPU ID of the CBS
function by referring to "ADD
URNCCBCPUID" and add CBS
cells by referring to "ADD
UCELLCBSSAC".The parameter









None Not involved Not involved























the switches. If the
SYS_INFO_UPDATE_FOR_IU_R
ST switch is turned off, the
BARRED_CELL_FOR_CSDOMAI
N_RST switch is invalid.The
impact on the equipment. When
the parameter
RNCAP_IMSI_HO_SWITCH is set
to 1, the
SNA_RESTRICTION_SWITCH
check box under the Handover
algorithm switch parameter in the
MML command "SET
UCORRMALGOSWITCH" cannot
Not involved be selected at the same time. Not involved
Not involved the switches. Not involved












































The retransmit mechanism is used

if the signaling is sent by adopting
RLC UM on Uu interface during
channel handover.In this case, the
setting of the corresponding
waiting response timer for UE
setup does not work. (For
example, when the channel
change form DCH to FACH or the
channel change from FACH to
DCH, the timer does not work.)
The retransmit timer is 2 second.
The RB reconfiguration message
may retransmit three times when
the timer expires.The parameter

reconfiguration does not work. (For

release does not work. (For







































































































































When this parameter is set to
65535, it is regarded that the state
transition from FACH or E_FACH
Not involved to PCH is not performed. Not involved



























Impact on Radio Network Performance
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
A greater value of this parameter indicates that this GSM cell is more possibly selected as the target cell
for the handover. If the value of this parameter is too great, a GSM cell that fails to provide qualified
services may be selected as the target cell for the handover, thus leading to call drops.
A smaller value of this parameter indicates that this GSM cell is less possibly selected as the target cell for
the handover. If the value of this parameter is too small, the MS may fail to be handed over to the GSM
cell timely, thus leading to call drops.
The larger the value of the parameter, the lower the probability of selecting neighboring cells. The smaller
the value the parameter, the higher the probability of doing so.
None
None
None
If this cell is the neighboring cell of the serving cell for the blind handover, it is considered as the target cell
for the blind handover and inter-system DRD. If the coverage of the WCDMA cell is not completely
included in that of the GSM cell, the blind handover or inter-system DRD may fail, thus leading to call
drops.
The RNC hands over the UE preferentially to the neighboring cell with a high priority. It is recommended
that the GSM cell that includes the entire WCDMA cell be assigned with a higher priority. Otherwise, the
UE may be handed over to the GSM cell that does not include the entire WCDMA cell, thus leading to call
drops, handover failures, or DRD failures.
A greater value of this parameter indicates that the inter-RAT DRD is less possibly triggered. A smaller
value of this parameter indicates that the inter-RAT DRD is more possibly triggered, however, with a low
success rate.
None
None
When the algorithm of neighboring cell combination is enabled, the total number of the neighboring cells
connected through links may exceed 32 if more than one link is in the active link set. RNC consider this
parameter as a condition for neighboring cell selection. That is, a neighboring cell with a high priority is
preferentially selected. If a neighboring cell is not configured with the priority identifier, the lowest priority is
assigned to this cell. If a low priority is improperly assigned to the neighboring cell to be measured, the
handover to this cell may fail. This leads to call drops.
None
None
If SRVCC is enabled, the VoIP service can be carried on 2G CS channels.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The higher the value of this parameter is, the lower the absolute threshold is. In this case, there are
greater possibilities of meeting the requirement for lowering the AMR speech rate. Thus, it is easier to
lower the AMR speech rate.
The higher the value of this parameter is, the lower the absolute threshold is. In this case, there are less
possibilities of meeting the requirement for stopping AMR speech rate adjustment. Thus, it is easier to
lower the AMR speech rate.
possibilities of meeting the requirement for raising the AMR speech rate. Thus, it is more difficult to raise
the AMR speech rate.
greater possibilities of meeting the requirement for stopping AMR speech rate increase. Thus, it is more
difficult to raise the AMR speech rate.
None
None
None
None
None
greater possibilities of meeting the requirement for lowering the wideband AMR speech rate. Thus, it is
easier to lower the wideband AMR speech rate.
possibilities of meeting the requirement for stopping wideband AMR speech rate adjustment. Thus, it is
easier to lower the wideband AMR speech rate.
possibilities of meeting the requirement for raising the wideband AMR speech rate. Thus, it is more difficult
to raise the wideband AMR speech rate.
greater possibilities of meeting the requirement for stopping wideband AMR speech rate increase. Thus, it
is more difficult to raise the wideband AMR speech rate.
None
None
None
None
None
None
None
When the switch is turned on, the RNC can automatically search for information about the cell's intra-
frequency neighboring cells that are not configured. The missing neighboring cells can be detected by
analysis of the information. Adding the missing neighboring cells helps reduce call drop rate and
interference.
Turning on the switch affects the performance of the RNC to some extent. Thus, we recommend turning
off the switch by default and turning on the detection switch only when the function of detecting missing
intra-frequency neighboring cells is needed.
When the switch is turned on, the RNC can automatically search for information about the cell's inter-
frequency neighboring cells that are not configured. The missing neighboring cells can be detected by
interference.
Turning on the switch affects the performance of the RNC to some extent. Thus, we recommend turning
off the switch by default and turning on the detection switch only when the function of detecting missing
inter-frequency neighboring cells is needed.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When the switch is turned on, the RNC can automatically search in the cell for information about the cell's
inter-RAT neighboring cells that are not configured. The missing neighboring cells can be detected by
interference. Turning on the switch affects the performance of the RNC to some extent. Thus, we
recommend turning off the switch by default and turning on the detection switch only when the function of
detecting missing inter-RAT neighboring cells is needed.
None
None
None
None
None
None
None
None
None
If the value is set too small, the UEs on the cell edge cannot receive the system messages properly. This
problem affects the coverage of the downlink common channel and furthermore the coverage of the cell. If
the value is set too great, it causes interference to other channels, occupies the downlink transmit power,
and affects the cell capacity.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
It is configured in the network planning.
None
None
None
None
None
None
None
None
The higher the value is, the stricter the synchronization process becomes, and the more difficult the
synchronization occurs. The lower the value is, the easier the synchronization occurs. If the link quality is
poor, a simple synchronization requirement leads to waste of the UE power and increase of uplink
interference.
If the value is excessively high, the link out-of-sync decision is likely to happen. If the value is excessively
low, out-of-sync is not likely to happen. But if the link quality is poor, it may result in a waste of the UE
power and increased uplink interference.
If the value is excessively low, there are few chances for the radio link to get synchronized. If the value is
excessively high, the radio link failure process is probably delayed, and the downlink interference
increases.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The larger the sum, the higher the handover priority of the neighboring cell. The smaller the sum, the lower
the handover priority of the neighboring cell. Usually it is configured to 0. The larger the parameter, the
easier of the handover to the neighboring cell. The smaller the parameter, the harder the handover to the
neighboring cell.
None
None
Setting this parameter to a smaller value limits downlink capacity and coverage. Setting this parameter to
a larger value increases interference between GSM and UMTS.
None
None
None
None
None
None
None
None
None
None
None
None
None
If the maximum transmit power of the PCPICH is configured too large, the cell capacity will be decreased
because a lot of system resources will be occupied and the interference with the downlink traffic channels
will be increased.
Setting of this parameter needs to be based on system environment such as cell coverage radius and
geological environment. In a cell that demands coverage, setting of this parameter must guarantee
downlink coverage. This parameter cannot be set to too small a value. In a cell that demands a certain
percentage of soft handover areas, setting of this parameter must guarantee the percentage required by
network planning. This parameter Setting of this parameter needs to be based on system environment
such as cell coverage radius and geological environment. In a cell that demands coverage, setting of this
parameter must guarantee downlink coverage. This parameter cannot be set to too small a value. In a cell
that demands a certain percentage of soft handover areas, setting of this parameter must guarantee the
percentage required by network planning. This parameter cannot be set to too large a value. Otherwise,
system resources are occupied, interference of downlink traffic channels is increased, and cell capacity is
reduced.
If the value is excessively low, UEs at the edge of cells fail in network searching, resulting in influence on
coverage of the downlink common channel. This finally affects the cell coverage. If the value is
excessively high, the power resources are wasted, and other channels are interfered seriously, thus the
cell capacity is influenced.
None
None
None
None
None
None
If this parameter is set to a greater value, the RNC excessively advances the time points of sending FP
frames, thereby occupying excessive space in the buffer of the NodeB.
If this parameter is set to a smaller value, FP frames sent by the RNC may fall out of the time windows of
NodeBs that do not participate in FP frame synchronization.
As a result, these NodeBs fail to process FP frames, and downlink data transmission is interrupted.
will be increased.
None
If MinPCPICHPower is excessively small, the cell coverage is affected.

None
The greater the power of the MICH,the higher of the success ratio of the MBMS paging. However, more
cell power resources are occupied.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
If the value is too high the system load after admission may be over large, which impacts system stability
and leads to system congestion. If the value is too low, the possibility of user rejects may increase,
resulting in waste in idle resources.
resulting in waste in idle resources and the failure to achieving network planning target.
resulting in waste in idle resource and the failure to achieving the network planning target.
resulting in waste in idle resources and the failure to achieving network planning target.
If the value is too high, power resources are wasted, which impacts system capacity. If the value is too
low, resources can be fully used and coverage may be impacted in case of insufficient resources.
None
If the value is too high, the system load after admission may be over large, which impacts system stability
If the value is too high, the system load after admission may be over large, which impacts system stability
If this value is too high, the possibility of rejecting HSUPA schedule services increases, which impacts
access success rate. If the value is too low, too many HSUPA schedule users may be admitted, which
impacts the admitted users and results in overload and system congestion.
impacts the admitted users and results in overload and system congestion.
impacts the admitted users and results in overload and system congestionRecommended.
None
If the value is too high, admission requirement of the HSDPA streaming service is strict, which improves
the service quality of the HSDPA streaming service but also may lead to HSDPA capacity waste. If the
value is too low, admission requirement of the HSDPA streaming service is loose, which allows more
HSDPA streaming services but QoS of the HSDPA streaming service cannot be guaranteed.
If the value is too high, admission requirement of the HSDPA BE service is strict, which improves the
service quality of the HSDPA BE service but also may lead to HSDPA capacity waste. If the value is too
low, admission requirement of the HSDPA BE service is loose, which allows more BE services but QoS of
the HSDPA BE service cannot be guaranteed.
If the value is too low, the cell HSDPA capacity may be reduces, leading to waste in HSDPA resources. If
the value is too high, HSDPA services may be congested.
The larger the value of this parameter is, the wider the coverage of the corresponding services will be.
When the downlink coverage is exceeded, the uplink coverage and downlink coverage of the service will
become unbalanced. If the values of these parameters are too small, the uplink coverage will probably be
smaller than the downlink coverage of the service.
When the uplink coverage is too large, the uplink coverage and downlink coverage of the service can
None
None
None
None
None
If the value is too high, HSUPA services may be congested. If the value is too low, the cell HSDPA
capacity may be reduces, leading to waste in HSUPA resources.
None
None
None
None
None
None
The backer position the value is in {SF4,SF8,SF16,SF32,SF64,SF128,SF256,SFOFF}, the less code and
credit resources reserved for handover UEs. The possibility of rejecting handover UE admissions
increases and performance of UEs cannot be guaranteed. The more frontal position the value is, the more
the possibility of rejecting new UEs is and some idle resources are wasted.
The backer position the value is in {SF4,SF8,SF16,SF32,SF64,SF128,SF256,SFOFF}, the less code and
credit resources reserved for handover UEs. The possibility of rejecting handover UE admissions
increases and performance of UEs cannot be guaranteed. The more frontal position the value is, the more
the possibility of rejecting new UEs is and some idle resources are wasted.
None
None
None
None
None
With the RTWP anti-interference switch enabled, if this parameter is set to a small value, the number of
equivalent users will be easy to be judged as overlarge. That is, the probability of accepting an admission
request becomes low, and OLC operations will be performed. In this case, cell capacity may not be fully
used. If this parameter is set to a great value, the number of equivalent users will be hard to be judged as
overlarge. That is, the probability of accepting an admission request becomes high, and OLC operations
may be cancelled. In this case, cell load may become heavy.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a small value within the valid range, it is unlikely to shut down a cell, and
therefore power consumption can hardly be reduced. If this parameter is set to a large value within the
valid range, it is likely to shut down a cell, but the call drop rate may increase.
valid range, it is likely to shut down a cell, but the call drop rate may increase.
valid range, it is likely to shut down a cell, but the call drop rate increases.
None
If more values are selected for this parameter, it is unlikely to shut down a cell, and therefore power
consumption can hardly be reduced.
None
Setting the parameter to too large a value reduces power saving of UEs using DRX. Setting the parameter
to too small a value puts UEs to DRX so rapidly that delay in data transmission or state transfer is
lengthened.
Setting the parameter to too large a value increases power saving of UEs using DRX but lengthens delay
in data transmission or state transfer. Setting the parameter to too small a value reduces power saving of
UEs using DRX.
Setting the parameter to too large a value reduces power saving of UEs using DRX. Setting the parameter
to too small a value puts UEs to DRX so rapidly that delay in data transmission or state transfer is
lengthened.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to too large a value, excessive useless data fills in the TB when only a few UEs
need to be paged. As a result, the receiving success rate of downlink data decreases. If this parameter is
set to too small a value, a larger TB is required although not too many UEs need to be paged. As a result,
the receiving success rate of downlink data decreases, too.
If this parameter is set to too large a value, excessive data fills in the TB when only a few UEs need to be
paged. As a result, the receiving success rate of downlink data decreases. If this parameter is set to too
small a value, too few paging lists are carried in one Paging Type 1 message. As a result, paging
messages are more likely to be congested and the paging success rate decreases.
Setting this parameter to too large a value wastes much power. Setting this parameter to too small a value
decrease the demodulation success rate of the HS-SCCH and the paging success rate.
Setting this parameter to too large a value wastes much power. Setting this parameter to too small a value
decreases the demodulation success rate of the HS-DSCH and the paging success rate.
Setting this parameter to too large a value wastes much power and downlink code resources. Setting this
parameter to too small a value decreases the demodulation success rate of the HS-DSCH and the paging
success rate.
Setting this parameter to too large a value causes data buffer size in the NodeB to be too large. If this
parameter is set to too small a value, frequent timing adjustment may occur due to delay variation.
Setting this parameter to too large a value causes data to be sent to the NodeB too early. As a result, the
NodeB buffer stays too long. Setting this parameter to too small a value causes frequent timing
adjustment.
If this parameter is set to a larger value, higher bandwidth is assigned to EPCH UEs, decreasing the
access success rate of non-EPCH UEs. If this parameter is set to a smaller value, non-EPCH UEs are
more likely to be admitted but their GBRs are less likely to be guaranteed.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
UE will start intra-frequency and inter-frequency measurements easily when this parameter is large. So
that better cells can be selected.
UE will start inter-system measurements easily when this parameter is large. So that better cells can be
selected.
None
None
None
None
None
None
In the hierarchical networking, if this parameter is set to ON, the following functions are provided:
1. Reducing the number of soft handovers for a slowly-moving UE
2. Handing a slowly-moving UE to a cell with large coverage, thus lowering the load of a cell with small
coverage.
If this parameter is set to a small value, the quick handover may not be triggered. That is, the UE cannot
be handed over to a cell with large coverage. This leads to the decrease in the number of soft handovers.
If this parameter is set to a large value, the quick handover may be triggered easily. This may lead to the
great increase in the load of the cell with a large coverage.
If this parameter is set to a very great value, the fast-speed handover may not be triggered. That is, the
UE cannot be handed over to a cell with large coverage. This leads to the decrease in the number of soft
handovers. If this parameter is set to a very small value, the fast-speed handover may be triggered easily.
This may lead to the great increase in the load of the cell with large coverage.
With a smaller value of this parameter, a more reliable result can be obtained from UE slow speed
decision. In this case, however, higher load may be carried by the CPU.
If this parameter is set to a very great value, the slow-speed handover may not be triggered. That is, the
UE cannot be handed over to a cell with small coverage. Under this situation, the load of a cell with large
coverage cannot be reduced.
If this parameter is set to a very small value, the slow-speed handover may not be triggered. That is, the
If this parameter is set to a very great value, the UE can be easily handed over to a cell with small
coverage. This may lead to the increase in the number of soft handovers.
If this parameter is set too large, the RNC may mistakenly determine that ping-pong handover to the best
cell occurs. If this parameter is set too small, ping-pong handover cannot be prevented. Thus, it is
recommended that this parameter be set according to the cell radius.
None
If only inter-frequency neighboring cells exist, inter-frequency handovers may be triggered. If only inter-
RAT neighboring cells exist, inter-RAT handovers may be triggered. If both inter-frequency and inter-RAT
neighboring cells exist and this parameter is set to SIMINTERFREQRAT(inter-frequency and inter-RAT
handover), both inter-frequency measurement and inter-RAT measurement can be performed.
The compressed mode is used in many scenarios. Therefore, user experience may be affected.
When the value of this parameter is changed, the event 2D/2F thresholds are changed accordingly. As a
result, inter-frequency or inter-RAT handover conditions are affected.
When this switch is set to ON, the number of inter-RAT handovers for CS services may increase. When
this switch is set to OFF, the number of inter-RAT handovers for CS services may decrease.
When this switch is set to ON, the number of inter-RAT handovers for PS services may increase. When
this switch is set to OFF, the number of inter-RAT handovers for PS services may decrease.
None
At the early stage of network deployment, or when the traffic model of subscribers in a cell is not known,
the parameter can be set to Automatic to have the HSDPA channel codes automatically allocated. If the
traffic model of subscribers in a cell is stable and known, the parameter can be set to Manual to select the
static allocation mode. Manual allocation leads to restriction of HSDPA code resource or leaves HSDPA
code resource idle.
If the parameter value is set too low, the HSDPA code resources will be limited and the HSDPA
performance is affected. If the parameter value is set too high, the HSDPA code resources are wasted,
thus increasing the admission rejection rate for R99 services.
None
None
In the scenarios like outdoor macro cells with power restricted, it is less likely to schedule multiple
subscribers simultaneously, so two HS-SCCHs are configured. In the scenarios like indoor pico with code
restricted, it is more likely to schedule multiple subscribers simultaneously, so four HS-SCCHs are
configured. If excessive HS-SCCHs are configured, the code resource is wasted. If insufficient HS-SCCHs
are configured, the HS-PDSCH code resource or power resource is wasted. Both affect the cell throughput
rate.
If the parameter value is set too low (negative value), the total HSPA power will be too low, thus impacting
the throughput of HSDPA subscribers at the border of a cell.
If the parameter value is unreasonable, the CQI in some scenarios will exceed the range of 0 to 30. As a
result, the NodeB MAC-hs cannot schedule the subscriber in the corresponding time or cannot schedule
multiple subscribers with the difference of channel conditions.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the parameter value is set too high, the downlink codes are wasted. If the parameter value is set too low,
the uplink throughput of the HSUPA is restricted.
If the parameter value is set too high, the downlink codes are wasted. If the parameter value is set too low,
the uplink throughput of the HSUPA is restricted.
If the parameter value is set too low, there is a risk that the cell throughput will be too low. If the parameter
value is set too high, there is a risk for high interference.
If the parameter value is set too low, the power of the non-serving radio link will be low and the data rate
on non-serving E-DCH will be reduced, thus impacting the transport rate of the UE in soft handover state.
If the parameter value is too high, the non-serving RL cannot send RG to the UE even in overloaded
situation.
None
None
None
None
None
If this parameter is set to a greater value, the effect of smoothing signals and the ability of anti-fast-fading
improve. However, the ability of tracing the signal change becomes low, and call drops are likely to occur
because handover is not performed in time. If this parameter is set to a smaller value, the number of
unnecessary hard handovers and ping-pong handovers increases.
None
None
None
None
None
If this parameter is set to a greater value, the quality of the current frequency is higher in the same
condition. In this case, inter-frequency handover is not likely to be triggered. If this parameter is set to a
smaller value, the quality of the current frequency is lower in the same condition. In this case, inter-
frequency handover is likely to be triggered. Generally, this parameter is set to 0 or 1. Whether the
handover is easy or difficult to trigger is not decided by setting this parameter.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
After handover, the inter-frequency measurement may be started again, and thus ping-pong handover
may perform. In order to prevent ping-pong handover, this parameter can be set greater than the start
threshold for event 2D or equal to the threshold of event 2F.
None
None
None
None
None
None
Setting this parameter to a smaller value reduces the impact of long duration of compression mode on the
serving cell. In this case, however, the compression mode may be disabled before the inter-frequency
handover of the UE. For the coverage-based inter-frequency handover, call drops may occur.
If this parameter is set to a smaller value, handover attempts increase when the inter-frequency handover
fails. In this case, the UE can be quickly handed over to the target cell whose load is reduced, thus
lowering the probability of call drops. More handover re-attempts, however, cause the increase in the RNC
load.
None
None
None
None
None
None
None
None
None
The advantage of the periodical reporting mode is that it can be used for repeated handover re-attempts
on the same cell when the handover fails, and that the subsequent algorithms can be flexibly developed.
In addition, the UE needs not to be informed when the parameters are changed. The drawback of
periodical reporting is that it requires large amount of signaling and increases the load on the air interface
and for signaling processing.
The advantage of event-triggered reporting is that the signaling transmission and processing load are
saved. Comparing the signal quality between intra-frequency and inter-frequency handovers, the ping-
pong effect in handover is prevented to some extent. The drawback of event-triggered reporting is that the
event is reported only once and cannot be changed to periodical reporting.
If this parameter is set to a larger value, call drops are likely to occur because handover is not performed
in time. If this parameter is set to a smaller value, unnecessary inter-RAT handovers may increase.
If the parameter value does not match the network environment (for example, the Ec/No measurement
quantity is used for event 3A measurement in areas with low RSCP), inter-RAT handover may fail.
unnecessary Inter-RAT handovers increases.
If this parameter is set to a greater value, the estimated general quality of the current frequency in the
same condition is higher. In this case, inter-RAT handover is unlikely to be triggered. If this parameter is
set to a smaller value, the estimated general quality of the current frequency in the same condition is
lower. In this case, inter-frequency handover is likely to be triggered. When the parameter value is set to 0,
the quality of the best cell in an active set is regarded as the general quality of an active set.
The setting of this parameter has impact on the Uu signaling traffic. If the period is too short and the
reporting frequency is too high, the RNC may have high load in processing signaling. If the period is too
long, the network cannot detect the signal changes in time, which may delay the inter-RAT handover and
thus cause call drops.
The setting of this parameter should consider the radio conditions (slow fading), actual handover distance,
and moving speed of the UE.
If this parameter is set to a greater value, the probability of ping-pong reporting or wrong decision is lower,
but the event may not be triggered in time.
The value of this parameter is associated with slow fading. If this parameter is set to a larger value, the
cell of another RAT where the UE needs to be handed over to must be of good quality. Therefore, the
criteria for triggering the inter-RAT handover decision is hard to be fulfilled, and the call drop rate will
increase. If this parameter is set to a smaller value, ping-pong handover is likely to occur.
The value of this parameter is associated with slow fading. If this parameter is set to a greater value, the
probability of incorrect decision becomes low; however, the handover algorithm becomes slow in
responding to signal change.
probability of incorrect handover decision becomes low; however, the handover algorithm becomes slow in
responding to signal change. This leads to the decrease in the number of handovers.
If the parameter is set to a larger value, handover is unlikely to be triggered. However, call drops may
increase as the parameter value increases.
If the parameter is set to "NOT_REQUIRED", handovers are likely to be triggered, but the handover
reliability is lower than the situation the parameter is set to "REQUIRED".
The setting of this parameter affects the proportion of the UEs in compressed mode in a cell and the
success rate of the hard handover. If this parameter is set to a greater value, hard handover is likely to be
triggered, but ping-pong handover may occur. If this parameter is set to a smaller value, hard handover is
unlikely to be triggered, but call drops may occur.
success rate of the hard handover. If the threshold for event 2F is set to a larger value, more UEs will
enter compressed mode, thus affecting user experience. If the threshold for event 2F is set to a smaller
value, it becomes difficult for UEs to trigger inter-RAT measurement, thus decreasing handovers.
If the threshold for event 2F is set to a larger value, more UEs will enter compressed mode, thus affecting
user experience. If the threshold for event 2F is set to a smaller value, it becomes difficult for UEs to
trigger inter-RAT measurement, thus decreasing handovers.
The setting of this parameter affects number of hard handovers. If this parameter is set to a greater value,
hard handover is likely to be triggered, but ping-pong handover may occur. If this parameter is set to a
smaller value, hard handover is unlikely to be triggered, but call drops may occur.
If this parameter is set to a larger value, event 3A is likely to be triggered. However, handover is likely to
be triggered when the frequency quality in the current system is acceptable for the UE if the value of this
parameter is set too large.
If the parameter is set to a smaller value, the UE cannot finish inter-RAT handover. If the parameter is set
to a larger value, the user experience is affected.
If this parameter is set to a larger value, the UEs handed out from the 2G network are unlikely to be
handed back to the 2G network. If this parameter is set to a smaller value, the effect of penalty is
unobvious, causing ping-pong handover between 2G and 3G networks.
If this parameter is set to a larger value, the UEs handed over from the 2G network are unlikely to be
handed over back to the 2G network. If this parameter is set to a smaller value, the risk for ping-pong
handovers increases.
If this parameter is set to a smaller value, handover attempts increase when the inter-RAT handover fails.
In this case, the UE can be quickly handed over to the target cell whose load is reduced, thus lowering the
probability of call drops. More handover re-attempts, however, cause the increase in the RNC load.
If this parameter is set to a larger value, handover attempts increase when the inter-RAT handover fails. In
this case, the UE can be quickly handed over to the target cell whose load is reduced, thus lowering the
If this parameter is set to a smaller value, many users will not be handed over to the 2G network in time. If
this parameter is set to a larger value, the penalty effect is unobvious.
If this parameter is set to a larger value, many users will not be handed over to the 2G network in time. If
this parameter is set to a smaller value, the penalty effect is unobvious.
None
None
None
None
None
None
None
None
None
None
None
None
unnecessary soft handovers and ping-pong handovers increases.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a greater value, the coverage area where a soft handover can be performed
reduces, for an incoming UE. However, the coverage area for an outgoing UE enlarges. If the UEs which
enter the area are equal to those who leave the area, the ratio of SHOs remains unchanged. If this
parameter is set to a greater value, the ability of resisting signal fluctuation improves and the number of
ping-pong handovers decreases. However, the handover algorithm becomes slow in responding to the
signal change.
signal change.
signal change.
signal change.
If this parameter is set to a too great value, the handover algorithm becomes slow in responding to the
signal change, and thus call drops may occur. If this parameter is set to a too small value, the handover
algorithm is more affected by signal fluctuation, and thus unnecessary inter-frequency blind handovers
may be triggered.
signal change.
If this parameter is set to a greater value, the thresholds for triggering soft handover for events 1A and 1B
are greater under the same conditions. In this case, the probability for adding a cell to the active set
decreases, and that for removing a cell from the active set increases. If this parameter is set to a smaller
value, the probability for adding a cell to the active set increases, and that for removing a cell from the
active set decreases.
If this parameter is set to a greater value, the average number of handovers decreases, but call drops may
occur.
According to TS 25.133 V3.6.0, intra-frequency measurement physical layer updates the measurement
result once every 200 ms. Therefore, the time-to-trigger mechanism is invalid if the interval is shorter than
200 ms. The time-to-trigger interval should be close to a multiple of 200 ms.
In addition, the UE at different rates may react differently to the same interval. For the fast-moving UE, the
call drop rate is more sensitive to the interval, whereas, for the slow-moving UE, the call drop rate is less
sensitive to the interval. Slow moving can also reduce ping-pong handovers and incorrect handovers.
Therefore, for the cell where most UEs are in fast movement, this parameter can be set to a smaller value,
whereas for the cell where most UEs are in slow movement, this parameter can be set to a greater value.
In addition, different events require different values of the time-to-trigger parameter: the event of adding
cells to the active set (event 1A) requires a smaller value of the time-to-trigger parameter; the events of
replacing cells in the active set (events 1C and 1D) require fewer ping-pong and incorrect handovers and
have no great impact on the call drop rate, and therefore the time-to-trigger parameter can be set to a
great value; the events of deleting cells in the active set (events 1B and 1F) require fewer ping-pong
handovers, and thus the time-to-trigger parameter can be adjusted, based on the actual network statistics.
If the interval for event 1A is shortened, handovers can be triggered timely, thus reducing the call drop
rate. If the interval for event 1B is prolonged, the average number of handovers and number of ping-pong
handovers decrease, thus reducing the call drop rate. These adjustments, however, may cause the growth
of the SHO ratio and the over use of the forward resources.
occur.
It is advised to set the time-to-trigger parameter for different events in a macro cell to a value from the
following ranges:
\Table 1. Typical time-to-trigger interval for events 1B or 1F on various channels
At the speed of 5 (km/h): the range is 640~1280 (ms), it is advise to set the time-to-trigger parameter to
1280 (ms).
640 (ms).
640 (ms).
Typical configuration of the time-to-trigger parameter for events 1B or 1F: the range is 640~1280 (ms), it is
advised to set the parameter to 640 (ms).
In a micro cell, the time-to-trigger parameter for different events should be shortened as required.
occur.
occur.
occur.
following ranges:
1280 (ms).
640 (ms).
640 (ms).
occur.
None
None
None
None
If the value is too great, the cell pilot may change fiercely, which is easy to lead to user call drops. If the
value is too small, the cell pilot may change smoothly. However, the response speed of the cell breathing
algorithm is decreased, impacting the algorithm performance.
When the cell breathing algorithm is activated, if the value is too small, the physical coverage of the cell is
limited so as to avoid cell capacity waste. If the value is too great, the physical coverage is expanded and
interference over other cells is increased.
When the cell breathing algorithm is activated, if the value is too small, the physical coverage of the cell is
limited so as to avoid cell capacity waste. If the value is too great, the physical coverage is expanded and
interference over other cells is increased.
None
The lower the LDR trigger and release thresholds are, the easier the system enters the preliminary
congestion status, the harder it is released from this status, the easier the LDR action is triggered, and the
more likely the users are affected. But, the admission success rate becomes higher since the resources
are preserved. The carrier shall make a trade-off between these factors.
The lower the OLC trigger threshold is, the easier the system is in the overload status. An excessively low
value of the OLC trigger threshold is very detrimental to the system performance. The lower the OLC
release threshold is, the harder the system releases the overload.
None
None
None
If the UL RTWP load is in restricted state, the RNC can change the TTI of the UE from 2 ms to 10 ms. If
this parameter is set too large, the TTI of the UE may be changed to 2ms in the case of overloading. This
may affect the cell capacity and fair diversity. If this parameter is set too small, the value of the TTI may be
changed by mistake when the load is reduced. This may affect KPIs and UE QoS.
If the UL RTWP load is in restricted state, the RNC can change the TTI of the UE from 2 ms to 10 ms. If
this parameter is set too large, the TTI of the UE may be changed to 2ms in the case of overloading. If the
RTWP load fluctuate acutely, it may lead to ping-pong switchover of the TTI. If this parameter is set too
small, the value of the TTI may fail to be changed to 2 ms in time. This may affect the QoS of a UE.
If this parameter is set to a small value, the conditions of unfairness between the R99 BE service rate and
HSUPA service rate can be easily met. In this case, the rate reduction of the R99 BE service is easily
triggered to improve the throughput of the HSUPA service. The decrease in the rate of the R99 BE service
also leads to the decrease in the R99 BE service throughput. If this parameter is set to a large value, the
rate reduction of the R99 BE service is not easily triggered.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The higher the parameter is, the higher the service rate of the user in handover is, and the more obviously
the cell load is decreased. However, high value of the parameter gives rise to the fluctuation and
congestion of the target cell load. The lower the parameter is, the smaller amplitude of the load decreases
as a result of the inter-frequency load handover, and the easier it is to maintain the stability of the target
cell load.
The higher the parameter is, the higher the service rate of the user in handover is, and the more obviously
the cell load is decreased. However, high value of the parameter gives rise to the fluctuation and
congestion of the target cell load. The lower the parameter is, the smaller amplitude of the load decreases
as a result of the inter-frequency load handover, and the easier it is to maintain the stability of the target
cell load.
The lower the parameter value is, the bigger the scope for selecting the MBMS services is, the more cell
load is decreased, the more effect there is on the MBMS service. At the same time, the cell overload is
significantly decreased while the impact on the MBMS services becomes bigger. The higher the parameter
value is, the smaller the scope for selecting the MBMS services is, the less cell load is decreased, the
more effect there is on the MBMS services, and the quality of services with high priority, however, can be
guaranteed.
The lower the code resource LDR trigger threshold is set, the easier the downlink code resource enters
the initial congestion status, the easier the LDR action is triggered, and the easier the subscriber
perception is affected. On the other hand, a lower code resource LDR trigger threshold causes a higher
admission success rate because more code resource is reserved.
None
None
The lower the parameter value is, the easier the credit enters the congestion status, the easier the LDR
action is triggered, and the easier the user experience is affected. A lower code resource LDR trigger
threshold, however, causes a higher admission success rate because the resource is reserved. The
parameter should be set based on the operator's requirement.
The lower the parameter value is, the easier the credit enters the congestion status, the easier the LDR
action is triggered, and the easier the user experience is affected. A lower code resource LDR trigger
threshold, however, causes a higher admission success rate because the resource is reserved. The
parameter should be set based on the operator's requirement.
The smaller this parameter value, the easier it is to find the qualified target cell for blind handover.
Excessively small values of the parameter, however makes the target cell easily enters the congestion
status. The higher the parameter value, the more difficult it is for the inter-frequency blind handover
occurs, and the easier it is to guarantee the stability of the target cell.
When the value is TRUE, users can be selected for inter-frequency handover during code resource
congestion, which can easily release code congestion and use multi-frequency resources. However, the
risk of inter-frequency blink handover increases.
None
None
Presupposition for analysis: 8SF4 < 7SF4 < ... < SF128 < SF256
If the parameter is set too big, the TTI switchove cannot be triggered until there is insufficient credit
remaining. In this case, the TTI switchover is triggered too late. If the parameter is set too small, the TTI
switchover may be triggered even when there is sufficient credit remaining.
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Setting the value of this parameter smaller can reduce the long-time impact of the compressed mode on
the serving cell. In this case, however, the compressed mode might be stopped earlier and as a result the
UE cannot trigger inter-frequency handover. If the parameter is set to a great value, the services may not
be set up successfully.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
A larger value of this parameter leads to a larger guaranteed coverage area of the MBMS service in the
case of heavy load in the cell.
None
None
None
None
A larger value of this parameter leads to a higher probability of using PTP transmission on the network.
Power control is available for PTP transmission, and thus the power consumption in PTP mode is lower
than that in PTM mode. In PTP mode, however, the quantities of code, CE, and other transmission
resources increase with the number of users. Therefore, the setting of this parameter should take into
consideration various resources, especially bottleneck resources of operators. The value of this parameter
should not be too large.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
UE cannot trigger inter-frequency handover.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The larger the value of the parameter is, the more easily event 2B, inter-frequency handover based on
Qos, and event 3A, inter-RAT handover based on Qos, can be triggered, and thus the more timely the
handover to the target cell can be performed.
None
None
None
None
The longer the trigger time is, the greater the effect of ignoring sudden changes is. Yet the response to
changes of the measured value becomes slower.
The greater the filtering coefficient is, the greater the smoothing effect is and the less the random
interference is. Yet the response to changes of the measured value becomes slower.
None
None
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is set too high, delay is caused.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is set to a too great value, the downlink transmit power on a single radio link
is too high. Thus, the downlink capacity is affected. If the value of this parameter is set to a too small
value, the coverage area of services is decreased, and the risk of call drops is increased.
If the value of this parameter is set to a too small value, the value range of the downlink transmit power
becomes large. Thus, the possibility of downlink transmit power drift is increased. If the value of this
parameter is set to a too great value, the downlink transmit power on a single radio link may exceeds the
required transmit power, thus wasting the downlink power.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the cell reselection threshold is set to a comparatively high value, the UE may frequently start cell
reselections, and the battery of the UE may be largely consumed. If the cell reselection threshold is set to
a comparatively low value, it is difficult for cell reselections to be started, and the UE may not timely reside
in the cells with good quality, affecting the quality of communication between the UTRAN and the UE.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to Both, it takes the UE longer time to measure LTE.
If this parameter is set to a larger value, filtering of signals becomes more obvious and the capability to
resist fast fading is increased. However, with the increase of this parameter value, the capability to track
signal change weakens and the call drop rate increases because handovers are untimely. If this
parameter is set to too small a value, unnecessary handovers are increased.
This parameter prevents a static UE or a UE moving slowly from staying in compressed mode for long
because of failure to meet handover conditions. Staying in compressed mode for long not only
deteriorates service quality, but also introduces extra interference to the system, thus reducing total
capacity. Most measurements of LTE and handover to LTE can be finished in 30s. Impact on network
performance: If the measurement timer length too short, the UE is unable to handover to LTE. If the
measurement timer length too long, the timer becomes useless. You can collect statistics for delay in
handovers to LTE and select a proper duration that meets the overwhelming majority of subscribers in
actual network planning.
Handovers to LTE vary in difficulty as settings of the LTE measurement quantity and corresponding
threshold vary. The settings are directly related to the ease of handovers to LTE.
How to set this parameter is related to slow fading. If the hysteresis is set to a larger value, the capability
to resist signal fluctuation is increased and the ping-pong effect is reduced. However, the handover
algorithm becomes less responsive to signal change. If the hysteresis for the handover to LTE is set to too
large a value, quality requirement for an LTE handover target cell increases and thus handover decision
criteria are difficult to reach. As a result, call drop rate increases. According to simulation results, if a cell is
a fast-moving cell, shadow shading variance is smaller because the expressway in the cell is flat with few
obstacles. Therefore you can reasonably reduce the parameter value to 1.5 dB. If a cell is a low speed
cell, shadow shading variance is larger because there are usually many buildings and even tall buildings in
the cell. Therefore you can reasonably increase the parameter value to 3.0 dB.
If this parameter is set to a larger value, the probability of false handover decision is reduced but the event
3C measurement report becomes less responsive to measurement signal change. If this parameter is set
to a smaller value, the event 3C measurement report becomes more responsive to measurement signal
change but the probability of false handover decision is increased.
According to the existing simulation results, the setting of this parameter effectively reduces the average
number of handovers and unnecessary handovers. The setting of this parameter can also reduce ping-
pong effect. UEs moving at different rates respond to the trigger delay time in a different way. Fast-moving
UEs are sensitive to the trigger delay time and thus subject to call drops. UEs at low speed are, however,
less sensitive to the trigger delay time. Thus this parameter can be set to a smaller value in a cell where
the majority UEs move fast and to a larger value in a cell where the majority UEs move slowly. This
parameter can be adjusted according to actual network statistics. Setting this parameter to a value less
than 480 ms is meaningless because the report period of inter-RAT measurements is 480 ms. If the trigger
delay time is set to a larger value, handovers are less likely to be performed, the capability to resist short-
term signal fluctuation is increased, and the probability to trigger unnecessary handovers is reduced.
However, call drop risks are increased, too.
None
If the parameter is set to a smaller value, CPICH power is more likely to be decreased. As a result,
coverage shrinks and coverage blind zone occurs, increasing the call drop rate. If the parameter is set to a
greater value, CPICH power is less likely to be decreased. As a result, CPICH power adjustment takes
lengthy time and the call drop rate cannot be reduced in time.
If the parameter is set to a greater value, CPICH power is more likely to be increased. As a result, CPICH
power is more likely to be increased and decreased in the way that ping-pong is played back and forth. If
the parameter is set to a smaller value, CPICH power is less likely to be increased. As a result, coverage
blind zone easily occurs, increasing the call drop rate.
If the parameter is set to a smaller value, CPICH power is adjusted at a slower pace. As a result, RTWP
change and uplink interference counteraction take longer time. If the parameter is set to a greater value,
CPICH power is adjusted at a faster pace. As a result, RTWP change and uplink interference
counteraction take shorter time. Cell coverage, however, may change rapidly, increasing the call drop rate.
None
None
None
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value is set too small, the UEs on the cell edge cannot receive the paging indication properly. This
problem may cause a misoperation of reading the PCH, waste the battery of the UE, affect the coverage
of the downlink common channel, and finally affect the cell coverage. If the value is too great, it causes
interference to other channels, occupies the downlink transmit power, and affects the cell capacity.
If the value is set too small, the UEs on the cell edge cannot receive the acquisition indication properly.
This problem affects the coverage of the downlink common channel and furthermore the coverage of the
cell. If the value is set too great, it causes interference to other channels, occupies the downlink transmit
power, and affects the cell capacity.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Enabling this algorithm supports the QoS differentiation but may decrease the system throughput of the
cell.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a large value within the valid range, a UE cannot adjust its retransmission type
for a long time, leading to performance loss. For example, if a UE cannot adjust its transmission type from
small retransmission to large retransmission for a too long time, the gain from large retransmission is
delayed, affecting the improvement of uplink throughput in the cell. If a UE cannot adjust its transmission
type from large retransmission to small retransmission for a too long time, the data rate of a UE cannot be
increased in time because of the limitation of the physical-layer data rate even if resources are sufficient,
affecting user experience. If this parameter is set to a small value within the valid range, the possibility of
frequent adjustments of retransmissions is increased.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If SRVCC is enabled, the VoIP service can be carried on 2G CS channels.

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a small value, the call drop rate of HSUPA services increases. If this parameter
is set to a large value, the network throughput reduces.
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Setting this parameter to too large a value causes GSM to wait for spectrum withdrawal for too long a
time. As a result, urgent spectrum withdrawal is frequently triggered. Setting this parameter to too small a
value causes UEs unable to finish their handovers, leading to call drops.
Setting this parameter to too large a value causes GSM to wait for spectrum withdrawal for too long a
time. As a result, urgent spectrum withdrawal is frequently triggered by GSM. Setting this parameter to too
small a value causes UEs unable to finish their handovers, leading to call drops.
Setting this parameter to too large a value deprives low-priority UEs of time to be handed over. As a result,
call drops occur. Setting this parameter to too small a value deprives UEs of time to finish measurement,
leading to call drops.
Setting this parameter to too large a value causes a large number of UEs to start the compressed mode,
requiring too many spreading codes. Setting this parameter to too small a value deprives low-priority UEs
of time to be handed over, leading to call drops.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The larger the value of the parameter is, the easier it is to be handed over to the GSM network. The
smaller the value of the parameter is, the harder it is to be handed over to the GSM network.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The larger the value of the parameter is, the more difficult it is for the UE to camp on the cell. The smaller
the value of the parameter is, the easier it is for the UE to camp on the cell. But if the value is excessively
small, it is possible that the UE cannot receive the system messages carried by PCCPCH.
When this parameter is not set to any value, the UE adopts the corresponding value of the current serving
cell, added through the ADD UCELLSELRESEL command. Generally, this parameter is not set to any
value.
None
The larger the value of the parameter is, the more difficult it is for the UE to camp on the cell. The smaller
the value of the parameter is, the easier it is for the UE to camp on the cell. But if the value is excessively
small, it is possible that the UE cannot receive the system messages carried by PCCPCH.
When this parameter is not set to any value, the UE adopts the corresponding value of the current serving
cell, added through the ADD UCELLSELRESEL command. Generally, this parameter is not set to any
value.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If MaxFachPower is set excessively low, a UE positioned at the cell edge may fail to receive the services
and signaling carried over the FACH, in a correct way. This will impact the downlink common channel
coverage and thus the cell coverage.
If MaxFachPower is set excessively high, other channels will be interfered and more downlink power
resources will be occupied. This will consequently impact the cell capacity.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a small value, the quick handover may not be triggered. That is, the UE cannot
be handed over to a cell with large coverage. This leads to the decrease in the number of soft handovers.
If this parameter is set to a large value, the quick handover may be triggered easily. This may lead to the
great increase in the load of the cell with a large coverage.
If this parameter is set to a very great value, the fast-speed handover may not be triggered. That is, the
UE cannot be handed over to a cell with large coverage. This leads to the decrease in the number of soft
handovers. If this parameter is set to a very small value, the fast-speed handover may be triggered easily.
This may lead to the great increase in the load of the cell with large coverage.
With a smaller value of this parameter, a more reliable result can be obtained from UE slow speed
decision. In this case, however, higher load may be carried by the CPU.
If this parameter is set to a very great value, the slow-speed handover may not be triggered. That is, the
If this parameter is set to a very small value, the slow-speed handover may not be triggered. That is, the
If this parameter is set to a very great value, the UE can be easily handed over to a cell with small
coverage. This may lead to the increase in the number of soft handovers.
If this parameter is set too large, the RNC may mistakenly determine that ping-pong handover to the best
cell occurs. If this parameter is set too small, ping-pong handover cannot be prevented. Thus, it is
recommended that this parameter be set according to the cell radius.
None
None
When the value of this parameter is changed, the event 2D/2F thresholds are changed accordingly. As a
result, inter-frequency or inter-RAT handover conditions are affected.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
It is configured in the network planning.

will be increased.
None

None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a greater value, more power resources are consumed in a cell. If this parameter
is set to a smaller value, network coverage decreases.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to 16QAM, the NodeB covers a smaller area with the same transmit power and
requires higher transmit power to cover the same area. If this parameter is set to QPSK, the cell uses
more channelization codes with the same IMB service rate.
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a greater value, the quality of the current frequency is higher in the same
condition. In this case, inter-frequency handover is not likely to be triggered. If this parameter is set to a
smaller value, the quality of the current frequency is lower in the same condition. In this case, inter-
frequency handover is likely to be triggered. Generally, this parameter is set to 0 or 1. Whether the
handover is easy or difficult to trigger is not decided by setting this parameter.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a smaller value, handover attempts increase when the inter-frequency handover
fails. In this case, the UE can be quickly handed over to the target cell whose load is reduced, thus
lowering the probability of call drops. More handover re-attempts, however, cause the increase in the RNC
load.
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a greater value, the probability for selecting the neighboring cell as the target cell
reduces. If this parameter is set to a smaller value, the probability for selecting the neighboring cell as the
target cell increases.
None
None
None
None
None
None
None
If this cell is the neighboring cell of the serving cell for the blind handover, it is considered as the target cell
for the blind handover and inter-system DRD. If the coverage of the WCDMA cell is not completely
included in that of the GSM cell, the blind handover or inter-system DRD may fail, thus leading to call
drops.
None
None
None
None
None
None
None
If this parameter is set to a greater value, the probability of selecting the neighboring cell becomes low. If
this parameter is set to a smaller value, the probability of selecting the neighboring cell becomes high.
If this parameter is set to a greater value, the probability of selecting the neighboring cell becomes low. If
this parameter is set to a smaller value, the probability of selecting the neighboring cell becomes high.
The advantage of the periodical reporting mode is that it can be used for repeated handover re-attempts
on the same cell when the handover fails, and that the subsequent algorithms can be flexibly developed.
In addition, the UE needs not to be informed when the parameters are changed. The drawback of
periodical reporting is that it requires large amount of signaling and increases the load on the air interface
and for signaling processing.
The advantage of event-triggered reporting is that the signaling transmission and processing load are
saved. Comparing the signal quality between intra-frequency and inter-frequency handovers, the ping-
pong effect in handover is prevented to some extent. The drawback of event-triggered reporting is that the
event is reported only once and cannot be changed to periodical reporting.
If this parameter is set to a larger value, call drops are likely to occur because handover is not performed
in time. If this parameter is set to a smaller value, unnecessary inter-RAT handovers may increase.
If the parameter value does not match the network environment (for example, the Ec/No measurement
quantity is used for event 3A measurement in areas with low RSCP), inter-RAT handover may fail.
If this parameter is set to a greater value, the estimated general quality of the current frequency in the
same condition is higher. In this case, inter-RAT handover is unlikely to be triggered. If this parameter is
set to a smaller value, the estimated general quality of the current frequency in the same condition is
lower. In this case, inter-frequency handover is likely to be triggered. When the parameter value is set to 0,
the quality of the best cell in an active set is regarded as the general quality of an active set.
probability of incorrect decision becomes low; however, the handover algorithm becomes slow in
responding to signal change.
probability of incorrect handover decision becomes low; however, the handover algorithm becomes slow in
responding to signal change. This leads to the decrease in the number of handovers.
If this parameter is set to a larger value, the UEs handed out from the 2G network are unlikely to be
handed back to the 2G network. If this parameter is set to a smaller value, the effect of penalty is
unobvious, causing ping-pong handover between 2G and 3G networks.
If this parameter is set to a larger value, the UEs handed over from the 2G network are unlikely to be
handed over back to the 2G network. If this parameter is set to a smaller value, the risk for ping-pong
handovers increases.
If this parameter is set to a smaller value, handover attempts increase when the inter-RAT handover fails.
In this case, the UE can be quickly handed over to the target cell whose load is reduced, thus lowering the
If this parameter is set to a larger value, handover attempts increase when the inter-RAT handover fails. In
this case, the UE can be quickly handed over to the target cell whose load is reduced, thus lowering the
None
None
None
None
None
None
None
None
None
None
None
improve; however, the ability of tracing the signal change becomes low and call drops are likely to occur
unnecessary soft handovers and ping-pong handovers increases.
Note that this parameter has great impact on the overall performance of the handover. Therefore, set this
parameter with caution.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
signal change.
signal change.
signal change.
signal change.
If this parameter is set to a too great value, the handover algorithm becomes slow in responding to the
signal change, and thus call drops may occur. If this parameter is set to a too small value, the handover
algorithm is more affected by signal fluctuation, and thus unnecessary inter-frequency blind handovers
may be triggered.
signal change.
If this parameter is set to a greater value, the thresholds for triggering soft handover for events 1A and 1B
are greater under the same conditions. In this case, the probability for adding a cell to the active set
decreases, and that for removing a cell from the active set increases. If this parameter is set to a smaller
value, the probability for adding a cell to the active set increases, and that for removing a cell from the
active set decreases.
occur.
occur.
following ranges:
1280 (ms).
640 (ms).
640 (ms).
occur.
occur.
occur.
following ranges:
1280 (ms).
640 (ms).
640 (ms).
occur.
None
None
None
None
None
None
None
If this parameter is set to a smaller value, the interval between intra-frequency measurement reports is
shorter, that is, the intra-frequency measurement takes a shorter period; however, the measurement
results are more affected by signal changes. This may cause incorrect handovers. If this parameter is set
to a greater value, the interval between intra-frequency measurement reports is longer, and the
measurement results are less affected by signal changes. This may increase the success rate of blind
handovers. In this case, however, the intra-frequency measurement takes a longer period of time, and the
handover may fail to be triggered timely.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
Not involved
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a small value, the rate reduction of the R99 BE service is frequently performed to
improve the fairness between the R99 BE service rate and HSUPA service rate. However, there is also a
possibility that another rate reduction is performed before the last rate reduction is effective. If this
parameter is set to a large value, the rate reduction of the R99 BE service is not timely performed, and
thus the fairness between the R99 BE service rate and HSUPA service rate cannot be improved.
If the parameter is set to a smaller value, CPICH power is more frequently adjusted. As a result, RTWP
change and uplink interference counteraction take shorter time. Cell coverage, however, may change too
rapidly, increasing the call drop rate. If the parameter is set to a greater value, CPICH power is less
frequently adjusted. As a result, RTWP change and uplink interference counteraction take longer time.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the parameter is set to a greater value, CPICH power adjustment takes longer time. If the parameter is
set to too small a value, CPICH power adjustment takes lengthy time. As a result, uplink RTWP
interference cannot be reduced in time and there fore the call drop rate cannot be reduced in time. If the
parameter is set to a smaller value, CPICH power adjustment takes shorter time. If the parameter is set to
too small a value, CPICH power is more likely to be increased and decreased in the way that ping-pong is
played back and forth. As a result, cell coverage changes rapidly, increasing the call drop rate.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
UE cannot trigger inter-frequency handover.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
When this parameter is set to "ON", the inter-frequency missing neighboring cells can be measured. The
extra measurement may prolong the measurement period and affect the timely handover.
When this parameter is set to "ON", the inter-frequency missing neighboring cells can be measured. The
extra measurement may prolong the measurement period and affect the timely handover.
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Presupposition for analysis: 8SF4 < 7SF4 < ... < SF128 < SF256
If the parameter is set too big, the TTI switchove cannot be triggered until there is insufficient credit
remaining. In this case, the TTI switchover is triggered too late. If the parameter is set too small, the TTI
switchover may be triggered even when there is sufficient credit remaining.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
Not involved
None
Not involved
Not involved
None
Not involved
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value is set too small, the UEs on the cell edge cannot receive the paging message properly. This
None
None
None
None
None
None
None
None
will be increased.
None
Setting of this parameter needs to be based on system environment such as cell coverage radius and
geological environment. In a cell that demands coverage, setting of this parameter must guarantee
downlink coverage. This parameter cannot be set to too small a value. In a cell that demands a certain
percentage of soft handover areas, setting of this parameter must guarantee the percentage required by
network planning. This parameter Setting of this parameter needs to be based on system environment
such as cell coverage radius and geological environment. In a cell that demands coverage, setting of this
parameter must guarantee downlink coverage. This parameter cannot be set to too small a value. In a cell
that demands a certain percentage of soft handover areas, setting of this parameter must guarantee the
percentage required by network planning. This parameter cannot be set to too large a value. Otherwise,
system resources are occupied, interference of downlink traffic channels is increased, and cell capacity is
reduced.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value of Max preamble retransmission is too small, the preamble power may fail to ramp to the
required value. This may result in UE access failure. If it is too large, the UE will repeatedly increase the
power and make access attempts, which may result in interference to other UEs.
If the value of Power ramp step is too large, the access procedure will be shortened, but it is more likely to
cause power waste. If it is too small, the access procedure will be extended in time, but transmit power
resources will be saved. This parameter must be set carefully. In addition, the higher the parameter value
is, the smaller impact "Constant Value for Calculating Initial TX Power" has on the network performance.
None
None
None
None
None
None
None
None
None
None
None
If the value is excessively low, the uplink interference may increase, and the uplink capacity may be
affected. If the value is excessively high, coverage may be affected.
None
None
None
None
None
If the value of Power ramp step is too large, the access procedure will be shortened, but it is more likely to
cause power waste. If it is too small, the access procedure will be extended in time, but transmit power
resources will be saved. This parameter must be set carefully. In addition, the higher the parameter value
is, the smaller impact "Constant Value for Calculating Initial TX Power" has on the network performance.
If the value of Max preamble retransmission is too small, the preamble power may fail to ramp to the
required value. This may result in UE access failure. If it is too large, the UE will repeatedly increase the
power and make access attempts, which may result in interference to other UEs.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is too low, whether the UE is in the stable low activity state cannot be
determined. If the value of this parameter is too high, the dedicated channel resources are wasted. This
parameter should be set on the basis of the PTT service model.
None
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is too high, congestion may occur over the common channel.
If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may
occur over the common channel.
If the value of this parameter is too high, congestion may occur over the common channel.
If the value of this parameter is too high, the period of reporting 4A event is delayed and congestion may
occur over the common channel.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The longer the UL AMRC timer is, the less frequently the AMRC mode is adjusted. In addition, the
response to measurement reports becomes slower accordingly.
None
None
None
The longer the UL AMRC timer is, the less frequently the AMRC mode is adjusted. In addition, the
response to measurement reports becomes slower accordingly.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The larger the value of the parameter is, the more easily event 2B, inter-frequency handover based on
Qos, and event 3A, inter-RAT handover based on Qos, can be triggered, and thus the more timely the
handover to the target cell can be performed.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is set too high, delay is caused.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the parameter value is excessively low, the UE access success rate may be reduced. If the parameter
value is excessively high, the UE probably spends a long time attempting repeatedly to access, which
increases the uplink interference.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to ON, pre-emption is triggered when PTM streaming bearer admission fails. That
is, a lower-priority MBMS bearer or a non-MBMS bearer is released. Thus, the ongoing service is
disrupted and call drop even occurs.
If this parameter is set to ON, a PTM streaming bearer might be pre-empted by an MBMS bearer of a
higher priority or a non-MBMS bearer in the case of congestion. Thus, the MBMS service is disrupted,
which has a relatively great impact because the PTM bearer serves more than one user.
If this parameter is set to ON, a PTM non-streaming bearer might be pre-empted by an MBMS bearer of a
higher priority or a non-MBMS bearer in the case of congestion. Thus, the MBMS service is disrupted,
which has a relatively great impact because the PTM bearer serves more than one user.
It is a waste of uplink resources if the uplink bandwidth of an MBMS service in PTP mode is high.
Therefore, it is recommended the default value be used.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a small value, the rate reduction of the R99 BE service is frequently performed to
improve the fairness between the R99 BE service rate and HSUPA service rate. However, there is also a
possibility that another rate reduction is performed before the last rate reduction is effective. If this
parameter is set to a large value, the rate reduction of the R99 BE service is not timely performed, and
thus the fairness between the R99 BE service rate and HSUPA service rate cannot be improved.
If the parameter is set to a smaller value, CPICH power is more frequently adjusted. As a result, RTWP
change and uplink interference counteraction take shorter time. Cell coverage, however, may change too
rapidly, increasing the call drop rate. If the parameter is set to a greater value, CPICH power is less
frequently adjusted. As a result, RTWP change and uplink interference counteraction take longer time.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the parameter is set to a greater value, CPICH power adjustment takes longer time. If the parameter is
set to too small a value, CPICH power adjustment takes lengthy time. As a result, uplink RTWP
interference cannot be reduced in time and there fore the call drop rate cannot be reduced in time. If the
parameter is set to a smaller value, CPICH power adjustment takes shorter time. If the parameter is set to
too small a value, CPICH power is more likely to be increased and decreased in the way that ping-pong is
played back and forth. As a result, cell coverage changes rapidly, increasing the call drop rate.
None
None
If the value is set too small, the UEs on the cell edge cannot receive the paging message properly. This
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
The greater the value of this parameter is, the more easily the event 1A is triggered.
The lower the value of this parameter is, the more easily the event 1B is triggered.
The greater the value of this parameter is, the less probable the incorrect decision is. Yet the response of
the event to the change of measured signals becomes slower accordingly.
The greater the value of this parameter is, the less probable the incorrect decision is. Yet the response of
the event to the change of measured signals becomes slower accordingly.
None
None
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a smaller value, ping-pong relocations may occur, thus affecting network
performance. If this parameter is set to a greater value, relocations may hardly occur, thus causing call
drops.
If this parameter is set to a smaller value, the current transmission may not meet the QoS delay
requirements. In this case, relocations cannot be triggered, thus affecting user experience. If this
parameter is set to a greater value, the current transmission delay may not meet the QoS delay
requirements. In this case, frequent relocations may trigger, thus affecting the RNC performance.
The parameter should be set on the basis of "Interval of Iur Resource Congestion Reporting". The
difference between the previous two values cannot be too large. Individually changing a parameter will
cause the time difference in the congestion reporting and the relocation triggering, and thus the algorithm
cannot be efficiently performed.
If this parameter is set to a greater value, more UEs may occupy common channels on the Iur interface,
and thus a large number of Iur resources are occupied. If this parameter is set to a smaller value, almost
no UE occupies common channel, and thus Iur resources are wasted.
This parameter determines the number of UEs over the Iur interface. If the parameter is set to a greater
value, a large number of unnecessary Iur resources are occupied. If this parameter is set to a smaller
value, the ping-pong relocation may occur.
If the relocation is not allowed to be initiated by the RT or NRT service, the corresponding service may
occupy more Iur resources.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If the CN forbids the service-based handover of UEs to LTE in the handover flag, a service-based or
coverage-based handover of UEs to LTE are forbidden. It is the case no matter whether the handover to
LTE is allowed on the RAN side. If the CN does not forbid the service-based handover of UEs to LTE in
the handover flag, whether the handover to LTE is allowed needs to be further determined according to
the setting of this parameter on the RAN side.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a large value within the valid range, data channels use excessive transmit power
and therefore the transmit power the can be used by control channels is low. This affects the performance
of DPCCH estimation, multipath searching, and E-DPCCH/HS-DPCCH demodulation. As a result, uplink
and downlink data transmissions, especially uplink data transmission, are affected. If this parameter is set
to a small value within the valid range, some data transmissions are not allocated sufficient transmit
power. As a result, demodulation performance deteriorates, and the HSUPA coverage area is not notably
enlarged.
If this parameter is set to a large value within the valid range, the E-DPDCH power offset of a large-
retransmission UE is large, leading to a low DPCCH SIR. As a result, the performance of channel
estimation and multipath searching becomes bad, uplink demodulation performance deteriorates, and
uplink throughput decreases. If this parameter is set to a small value within the valid range, the DPCCH
SIR of a large-retransmission UE is high. As a result, uplink control channels use excessive transmit
power, decreasing uplink capacity.
If this parameter is set to a large value within the valid range, the E-DPDCH power offset of a small-
retransmission UE with low-speed data transmission is large, leading to a low DPCCH SIR. As a result,
the performance of channel estimation and multipath searching becomes bad, uplink demodulation
performance deteriorates, and uplink throughput decreases. If this parameter is set to a small value within
the valid range, the DPCCH SIR of a small-retransmission UE with low-speed data transmission is high.
As a result, uplink control channels uses excessive transmit power, decreasing uplink capacity.
retransmission UE with high-speed data transmission is large, leading to a low DPCCH SIR. As a result,
the valid range, the DPCCH SIR of a small-retransmission UE with high -speed data transmission is high.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to a large value within the valid range, data channels use excessive transmit power
and therefore the transmit power the can be used by control channels is low. This affects the performance
of DPCCH estimation, multipath searching, and E-DPCCH/HS-DPCCH demodulation. As a result, uplink
and downlink data transmissions, especially uplink data transmission, are affected. If this parameter is set
to a small value within the valid range, some data transmissions are not allocated sufficient transmit
power. As a result, demodulation performance deteriorates, and the HSUPA coverage area is not notably
enlarged.
If this parameter is set to a large value within the valid range, the E-DPDCH power offset of a large-
retransmission UE is large, leading to a low DPCCH SIR. As a result, the performance of channel
estimation and multipath searching becomes bad, uplink demodulation performance deteriorates, and
uplink throughput decreases. If this parameter is set to a small value within the valid range, the DPCCH
SIR of a large-retransmission UE is high. As a result, uplink control channels use excessive transmit
power, decreasing uplink capacity.
retransmission UE with low-speed data transmission is large, leading to a low DPCCH SIR. As a result,
the valid range, the DPCCH SIR of a small-retransmission UE with low-speed data transmission is high.
retransmission UE with high-speed data transmission is large, leading to a low DPCCH SIR. As a result,
the valid range, the DPCCH SIR of a small-retransmission UE with high -speed data transmission is high.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
If this parameter is set to Both, it takes the UE longer time to measure LTE.
If this parameter is set to a larger value, filtering of signals becomes more obvious and the capability to
resist fast fading is increased. However, with the increase of this parameter value, the capability to track
signal change weakens and the call drop rate increases because handovers are untimely. If this
parameter is set to too small a value, unnecessary handovers are increased.
This parameter prevents a static UE or a UE moving slowly from staying in compressed mode for long
because of failure to meet handover conditions. Staying in compressed mode for long not only
deteriorates service quality, but also introduces extra interference to the system, thus reducing total
capacity. Most measurements of LTE and handover to LTE can be finished in 30s. Impact on network
performance: If the measurement timer length too short, the UE is unable to handover to LTE. If the
measurement timer length too long, the timer becomes useless. You can collect statistics for delay in
handovers to LTE and select a proper duration that meets the overwhelming majority of subscribers in
actual network planning.
How to set this parameter is related to slow fading. If the hysteresis is set to a larger value, the capability
to resist signal fluctuation is increased and the ping-pong effect is reduced. However, the handover
algorithm becomes less responsive to signal change. If the hysteresis for the handover to LTE is set to too
large a value, quality requirement for an LTE handover target cell increases and thus handover decision
criteria are difficult to reach. As a result, call drop rate increases. According to simulation results, if a cell is
a fast-moving cell, shadow shading variance is smaller because the expressway in the cell is flat with few
obstacles. Therefore you can reasonably reduce the parameter value to 1.5 dB. If a cell is a low speed
cell, shadow shading variance is larger because there are usually many buildings and even tall buildings in
the cell. Therefore you can reasonably increase the parameter value to 3.0 dB.
If this parameter is set to a larger value, the probability of false handover decision is reduced but the event
3C measurement report becomes less responsive to measurement signal change. If this parameter is set
to a smaller value, the event 3C measurement report becomes more responsive to measurement signal
change but the probability of false handover decision is increased.
According to the existing simulation results, the setting of this parameter effectively reduces the average
number of handovers and unnecessary handovers. The setting of this parameter can also reduce ping-
pong effect. UEs moving at different rates respond to the trigger delay time in a different way. Fast-moving
UEs are sensitive to the trigger delay time and thus subject to call drops. UEs at low speed are, however,
less sensitive to the trigger delay time. Thus this parameter can be set to a smaller value in a cell where
the majority UEs move fast and to a larger value in a cell where the majority UEs move slowly. This
parameter can be adjusted according to actual network statistics. Setting this parameter to a value less
than 480 ms is meaningless because the report period of inter-RAT measurements is 480 ms. If the trigger
delay time is set to a larger value, handovers are less likely to be performed, the capability to resist short-
term signal fluctuation is increased, and the probability to trigger unnecessary handovers is reduced.
However, call drop risks are increased, too.
None
None
None
None
None
None
None
If the value of this parameter is too high, congestion may occur over the FACH channel.
If the value of this parameter is too high, the 4A event reporting will be delayed. This may result in
congestion over the FACH channel.
None
None
None
None
None
None
None
None
None
None
If the value of this parameter is too high, congestion may occur over the E-FACH channel.
congestion over the E-FACH channel.
None
If the value of this parameter is too low, it can not judge whether the UE is in low activity state. If the value
of this parameter is too high, the dedicated channel resources are wasted. This parameter should be set
on the basis of the BE service model.
of this parameter is too high, the common channel resources are wasted. This parameter should be set on
the basis of the BE service model.
on the basis of the real-time service model.
of this parameter is too high, the dedicated channel resources will be wasted. This parameter should be
set on the basis of the BE service model.
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Not involved
Not involved
Not involved
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Introduced in Version Attribute
Versions earlier than
BSC6900 V900R011 Radio

BSC6900 V900R011 Transport



BSC6900 V900R011 Equipment
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Paralistforumts Huawei Good

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Paralistforumts Huawei Good

Uploaded by

Copyright:

Available Formats

BSC6900 UMTS V900R013C00

Huawei Technologies Co., Ltd.

Copyright © Huawei Technologies Co., Ltd. 2011. All rights reserved.

Trademarks and Permissions

hout prior written consent of Huawei Technologies Co., Ltd.

Each parameter is described in the following aspects.

Impact on Radio Network Performance

Enumeration number corresponding to the GUI value of a parameter of the enumeration

Parameter value unit

Parameter values recommended for different scenarios

UDPUCFGDATA MaccPageRepeatTimes Repeat Times of Macc Paging

AAL2PATH ANI Adjacent Node ID

AAL2PATH PATHID AAL2 path ID

AAL2PATH CARRYT Bearing type

AAL2PATH CARRYF Bearing subrack No.

AAL2PATH CARRYSN Bearing slot No.

AAL2PATH CARRYUNILNKN Bearing UNI link No.

AAL2PATH CARRYIMAGRPN Bearing IMA group No.

AAL2PATH CARRYFRAATMLNKN Bearing FRAATM link No.

AAL2PATH CARRYNCOPTN Bearing NCOPT port No.

AAL2PATH CARRYVPN Bearing ATM logic port No.

AAL2PATH RSCGRPN Rscgrp No.

AAL2PATH VPI Bearing VPI

AAL2PATH VCI Bearing VCI

AAL2PATH TXTRFX TX traffic record index

AAL2PATH RXTRFX RX traffic record index

AAL2PATH OWNERSHIP AAL2 path ownership

AAL2PATH TRMLOADTHINDEX TRM load threshold index

AAL2PATH TIMERCU Timer_CU timer

AAL2RT NSAP Destination ATM address

AAL2RT ANI Adjacent Node ID

AAL2RT RTX Route index

Destination ATM address

AAL2TMR ESTREQTMR Establishment request timer

AAL2TMR ESTINDTMR Establishment indication timer

AAL2TMR RELREQTMR Release request timer

AAL2TMR RELINDTMR Release indication timer

AAL2TMR BLOREQTMR Blocking request timer

AAL2TMR UBLREQTMR Unblocking request timer

AAL2TMR RESREQTMR Reset request timer

AAL2TMR MODINDTMR AAL2 modifying indication timer

ADJMAP ANI Adjacent Node ID

ADJMAP ITFT Interface Type

Transport Type of the adjacent

ADJMAP CNMNGMODE Resource Management Mode

ADJMAP CNOPINDEX CN Operator index

ADJMAP TMIGLD Gold user TRMMAP index

ADJMAP TMISLV Silver user TRMMAP index

ADJMAP FTI Factor table index

ADJMAP LEIGLD Gold user Load EQ index

ADJMAP LEISLV Silver user Load EQ index

ADJMAP LEIBRZ Bronze user Load EQ index

ADJNODE ANI Adjacent Node ID

ADJNODE NAME Adjacent Node Name

ADJNODE NODET Adjacent Node Type

ADJNODE NODEBID NodeB ID

ADJNODE SGSNFLG SGSN FLAG

ADJNODE TRANST Transport Type

ADJNODE DPX DPX Index

ADJNODE UPPERANI Upper Ani

ADJNODE SRN Subrack No.

ADJNODE SN Slot No.

ADJNODE SAALLNKN SAAL link No.

ADJNODE QAAL2VER Qaal2 Protocol Version