Professional Documents
Culture Documents
Product UMTS/GSM
Template Type GROUND/RADIO
Template Name GU-SDR CM Optimization
Template Version V4.11.10.14P06
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 1 页
ZTE中兴 内部公开▲
PA Device PaDevice
Tx Device TxDevice
Rx Device Set RxDeviceSet
Rx Device RxDevice
RET Device Ret
Rf Cable RfCable
Embedded Power Device EPm
Power Outlet Device Set PowerOutletDeviceSet
Power Outlet Device PowerOutletDevice
Power Device Set PmDeviceSet
Bts Auxiliary Peripheral Device AuxUnit
AISG Device AisgDevice
Fan Device FanDevice
Ethernet Switching Device Set EthernetSwitchDeviceSet
Ethernet Switching Device EthernetSwitchDevice
Special Operation & Maintenance VsOam
OMC Channel ItfUniBts
Operator Operator
Plmn Plmn
Transport Network TransportNetwork
Physical Layer Port PhyLayerPort
DHCP Relay DhcpRelay
ATM Layer Link AtmLayerLink
AAL2 Aal2
SaalUni SaalUni
ALCAP Alcap
Bts Cascade BtsCascade
HDLC Channel Hdlc
PPP Link PppLink
Ethernet Link Layer EthernetLink
Ethernet Fault Detection EthernetOam
Bandwidth Control Rule BandwidthCtrlRule
IP Layer IpLayerConfig
IKE Policy IKEPolicy
IPSec Proposal IPSecTransformSet
Access Control Rule AccessControlList
IPSec Config IPSecConfig
Certificate Management Protocol Configuratio CmpConfig
Qos Mapping QosMap
SCTP Sctp
Ethernet Maintenance Domain EthernetCfmMd
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 2 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 3 页
ZTE中兴 内部公开▲
Remark
Equipment Object
options.
options.
options.
options.
options.
options.
options.
options.
options.
options.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 4 页
ZTE中兴 内部公开▲
mentFunction
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 5 页
OMCSUBNE
ModInd SDRMEID USERLABEL NODEBMEADDR
TID
Modify ManagedElement ManagedElement ManagedElemen
Subnet ID
Indication ID User Label t IP Address
Same in an IPV4.
A:Add, Unique in
OMMB. Cannot use the Unique in whole
P:Pass subnetwork.
Can fill in invalid characters, network.
Does not Can fill in with 1
with 1 during e.g. < > & ' " \ / : * ? Can fill in with
support the during LMT
LMT |#%@, 0.0.0.0 during
modification. importing.
importing. LMT importing.
It is unnecessary to It is unnecessary to
fill in the option in fill in the option in
Format:
GSM single mode UMTS single mode
v11.02.01
site. site.
65535:Invalid. 65535:Invalid.
double:[- double:[-
string:[0..40] string:[0..40] string:[0..80]
180.000000..180.000000] 90.000000..90.000000]
0:Release Connection
0:Normal
1:No Release
1:Testing
Connection
R R R
1 0
ZTE中兴 内部公开▲
0:Non-stack,
A,P long:[0..4095] long:[0..65535] 1:Master-slave frame stack
<default:0>
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 11 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 12 页
ZTE中兴 内部公开▲
adminState
R-W
0
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 13 页
ModInd OMCSUBNETID SDRMEID RackId rackNo
Modify
Subnet ID ManagedElement ID Rack ID Rack No.
Indication
A,P long:[0..4095] long:[0..65535] long:[1..65535] long:[1..201]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 16 页
RSU60-GU188,
ADTR-GU858,
ADTR-GU908,
ZTE中兴 ADTR-GU188, 内部公开▲
ADTR-GU198,
RSU60E-GU858,
RSU60E-GU908,
productData_product
slotNo RSU60E-GU188, ctrlAuxCabinetNo isHighPriority
Name
RSU60E-GU198, Controlled Auxiliary Abinet Whether high
Slot No. Board Name
RSU82-GU9016, No priority
RSU82-GU1816,
RSU82-GU8516,
RSU82-GU1916,
1:Y,
RSU82-U2112,
long:[1..23] string:[0..201] long:[2..255] 0:N
RSU82-GU9018D,
<default:0>
RSU82-L268,
The power-supply
RSU82 S9000(B8A),
level needed by the
RSU82 S1800(B8A),
board. The default
RSU82 S2100(B6A), Fill out the attribute for the
priority is low. When
RSU82 S2100(B8A), FCE in an auxiliary cabinet.
load is shared, NE is
For some boards, the R8880A-U2112, The auxiliary cabinet is only
allocated
slot where they are R8882A-U2112, used by FCE boards, which
automatically
inserted is fixed and R8890-U216, provide cooling function for
according to the
can not modified. TTR-G902, the devices of other
enhanced load
CC board in slot 1, SA TTR-G182, manufacturers.The
sharing algorithm. In
board and PM board TTR-G904, ctrlAuxCabinetNo can not be
OMMB, it can be
should be configured. TTR-G184, duplicate, it also can not be
manually adjusted to
R8882-GUL9012, the same as cabinetPosition
high priority, and then
R8882-GUL1812, of Rack object.
both PM boards
R8882-GUL8512,
Primary Key R-I R supply power
R-W-I for the
R8882-GUL1912,
1 CC 0 board.
R8882-GUL9018D,
3 FS R8882-L268, 0
5 UBPG
R8882 S9000(B), 0
7 BPC
R8882 S2100(B), 0
13 SAR8882-S9000C, 0
14 PMR8882-S1800C, 0
R8882 S8500(B6A),
1 RSU60E-GU908
R8882 S9000(C6B),
0
1 RSU60E-GU908
R8882 S1800(C6B), 0
7 FCE
R8882 S1900(B5A), 0
1 RSU60E-GU908
RSU82 S8500(B8A), 0
1 RSU40-U216
RSU82 S1900(B6A), 0
1 RSU02-G902,
RSU40-U216 0
RSU02-G182,
RSU02-G904,
RSU02-G184,
R8880A-U1712,
R8881 S9000(B8A),
R8881 S9000(B8B),
R8881 S9000(B8C),
R8881 S1800(B8C),
R8881 S2100(B8C),
R8881 S8500(B8B),
R8881 S8500(B8C),
R8881 S1700(B8B),
R8881 S1700(B8C),
R8881 S1900(B8B),
R8881 S1900(B8C),
R8881 S1800(B8A),
R8881 S1800(B8B),
R8881 S2100(B8A),
R8881 S2100(B8B),
R8881 S2100(B6A),
R8881 S2100(B6B),
RSU40-U218,
R8882 S1800(B),
R8882 S8500(B6B),
R8882 S1900(B6B),
RSU82 S8500(B8B),
RSU82 S1900(B6B),
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传>
RSU82 S2100(B8B), 共 529 页 , 第 17 页
R8882 S9000(B6C),
R8882 S1800(B6C),
RSU60E-GU90C,
ZTE中兴 内部公开▲
adminState
R-W
0
0
0
0
0
0
0
0
0
0
0
0
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 18 页
ZTE中兴 内部公开▲
ipv4
A,P long:[0..4095] long:[0..65535]
<default:0.0.0.0>
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 19 页
8:GMT - 8:00,
10:GMT - 7:00,
12:GMT - 6:00,
14:GMT - 5:00,
ZTE中兴15:GMT - 4:30, 内部公开▲
16:GMT - 4:00,
17:GMT - 3:30,
18:GMT - 3:00,
timeZone clockSynPeriod summTimeStart summTimeEnd
20:GMT - 2:00, Clock Synchronization Summer Time Summer Time
Time Zone
22:GMT - 1:00, Period Start End
24:GMT - 0:00,
26:GMT + 1:00,
28:GMT + 2:00,
long:[1..48]
30:GMT + 3:00, string:[0..20] string:[0..20]
<default:24>
31:GMT + 3:30,
32:GMT + 4:00,
33:GMT + 4:30, Format: MM-
Format: MM-
34:GMT + 5:00, DD HH:mm.
Indicates the time DD HH:mm.
35:GMT + 5:30, Indicates the
synchronization interval. Indicates the
51:GMT + 5:45, end time of
The base station start time of
36:GMT
Indicates + 6:00,
the time zone of the summer time.
performs time summer time. It
37:GMT + 6:30,
base station. It is allowed
synchronization with the is allowed that
38:GMT + 7:00, that the
NTP at this interval. Unit: the summer
40:GMT + 8:00, summer time is
hour. time is a cross-
42:GMT + 9:00, a cross-year
year range.
43:GMT + 9:30, range.
44:GMT R-W-I
+ 10:00, R-W-I R-W R-W
34 46:GMT + 11:00, 24
48:GMT + 12:00,
50:GMT + 13:00
<default:40>
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 20 页
ZTE中兴 内部公开▲
isSuppSummTime
Support Summer
Time or not
1:Y,
0:N
<default:0>
Indicates whether to
enable summer time.
R-W-I
0
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 21 页
ZTE中兴 内部公开▲
1: Internal GNSS,
3: External GNSS,
5: Cascade GNSS,
4: 1PPS+TOD,
long: 6: BITS-2MHz,
A,P long:[0..4095] long:[0..65535]
[1..4294967295] 7: BITS-2Mbps,
8: Line,
11: 1588,
13: SyncE
<default:1>
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill
in this column.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 22 页
ZTE中兴 内部公开▲
0: GSM/UMTS Frequency
Sync,
1: GSM FrameNumber Sync.
long:[1..8] UMTS Frequency Sync,
long:[0..86400]
<default:1> 2: GSM Frequency Sync.
UMTS FrameNumber Sync,
3: GSM/UMTS FrameNumber
Sync
Unit: s
This attribute indicates that if the current clock
reference failed, the time gap when the current
This attribute indicates the
reference changed to the backup reference.
mode used by the clock module
{ClockDevice.clockType == 11}[30..86400],
for extracting the GNSS clock.
{ClockDevice.clockType == 13}[0..86400],
"1": indicates the The frame number
{ClockDevice.clockType == 8}[0..86400],
highest priority. synchronization mode has a
{ClockDevice.clockType == 6}[0..86400],
higher precision than the
{ClockDevice.clockType == 7}[0..86400],
frequency synchronization
{ClockDevice.clockType == 1}[300..86400],
mode.
{ClockDevice.clockType == 3}[300..86400],
{ClockDevice.clockType == 4}[300..86400],
{ClockDevice.clockType == 5}[300..86400]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 23 页
ZTE中兴 内部公开▲
gnssClockData_cableDel gnssClockData_cableT
gnssClockData_receiverType
ay ype
Length of GNSS
GNSS Cable Type GNSS Receiver Type
Antenna Feeder Cable
1:GPS,
0: Multiplexing input,
long: [0..8000] 2:GLONASS,
1: Distribution input
3:GPS+GLONASS
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 24 页
ZTE中兴 内部公开▲
gnssClockData_frmMajorAlmThres gnssClockData_frmCritiAlmThres
Critical Alarm Threshold of GNSS
Major Alarm Threshold of GNSS Clock
Clock Reference Source Lost
Reference Source Lost during Frame
during Frame Number
Number Synchronization
Synchronization
{gnssClockData_frameCriticalAlarmT
{gnssClockData_frameMajorAlarmThres}
hres}
long: [20..4320]
long: [1..168]
Unit: hrs.
Unit: minute,step: 20.
This attribute indicates the threshold
This attribute indicates the threshold for
for reporting a critical alarm when the
reporting a major alarm when the GNSS
GNSS clock reference source is lost
clock reference source is lost during frame
during frame number synchronization.
number synchronization. In the case of
In the case of threshold crossing, a
threshold crossing, a major alarm, "loss of
critical alarm, "loss of GNSS clock
GNSS clock reference source", is raised.
reference source", is raised.
General value:20
General value:8
R-W R-W
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 25 页
ZTE中兴 内部公开▲
gnssClockData_longitu
gnssClockData_freCritiAlmThres gnssClockData_revOperatingMode
de
Critical Alarm Threshold of GNSS
Longitude of Reciver
Clock Reference Source Lost during Receiver Operating Mode
Antenna
Frequency Number Synchronization
{gnssClockData_receiverOperatingMo
{gnssClockData_freqCriticalAlarmThres double:[-
de}
} 180.000000..180.0000
1:Survey In,
long: [1..180] 00]
2:Fixed Mode
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 26 页
ZTE中兴 内部公开▲
gnssClockData_latitu gnssClockData_minStarN
gnssClockData_altitude
de um
Latitude of Reciver Height of Reciver Mimimum Number of
Antenna Antenna Search Star
double:[-
90.000000..90.00000 long: [0..10000] long: [1..4]
0]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 27 页
ZTE中兴 内部公开▲
gnssClockData_enableCasOutput gnssClockData_casCableDelay
Support Clock Cascade Output or
Length of Cascade Cable
not
{gnssClockData_enableCascadeOut
{gnssClockData_cascadeCableDel
put}
ay}
0:Not support,
long: [0..15]
1:Support
R-W R-W
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 28 页
ZTE中兴 内部公开▲
tod1PpsData_cascadeCableLengt
isSSM
h
Enable SSM or not Length of Cascade cable
1:Y,
0:N long:[0..15]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 29 页
ZTE中兴 内部公开▲
tod1PpsData_inputBardRate tod1PpsData_timeInputType
0:115200,
1:57600,
2:38400,
0:Multiplexing input,
3:19200,
1:Distribution input
4:9600,
5:4800,
6:2400
R-W R-W
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 30 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rack
A,P long:[0..4095] long:[0..65535] No}
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 31 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_subRac {SdrDeviceGroup_slot
long: long:[0..255]
kNo} No}
[1..4294967295] <default:0>
long:[1..2] long:[1..23]
Generated
automatically, it is
unnecessary to fill in
this column.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 32 页
ZTE中兴 内部公开▲
0: Alarm appears if
0: Input dry contact,
0: Output low level, contact is closed, 1:Y,
1: Output dry contact string: [0..127]
1: Output high level 1: Alarm appears if 0:N
<default:0>
contact is open
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 33 页
The dry contact is valid when the
type is input.
The customized dry contact ID must
be from 198092550 to 198092599,or
ZTE中兴 内部公开▲
from 198096424 to 198096473.
Non-self-defined dry contact range:
198092044:DooralmNo control alarm, userLabel
198092045:Flooding alarm,
198092046:Smog
Dry Contact Alarm alarm,
No. User Label
198092047:Infrared alarm,
198092048:Air conditioner fault,
198092049:Lightning protection
device alarm,
198092051:PSU alarm,
198092052:PSU fan alarm,
long string:[0..128]
198092068:Base station has a main
power cut-off alarm,
198092206:Battery alarm,
198092207:AC power-cut alarm,
198092208:Rectifier model alarm,
198092209:Thermoelectric cooler
alarm, Cannot use the
198092462:Differential Pressure invalid
Alarm, characters, e.g.
198092259:Battery low-voltage <>&'" \/: ?
alarm, #%@,
198092260:Faulty external device
connected at R-W
a dry contact, R-W
198092208
198092261:Outdoor lightning
198092550 protection box alarm,
198092262:Breaker alarm in indoor
198092207
lightning protection box,
198092263:Lightning protection
device alarm in indoor lightning
protection box,
198092264:Over-voltage alarm of
main power input,
198092265:Main power input power-
cut alarm,
198092266:Under-voltage alarm of
main power input,
198092363:Faulty main power
alarm,
198092267:General fault of main
power,
198092268:PWR monitoring unit
alarm
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 34 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rack
A,P long:[0..4095] long:[0..65535] No}
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 35 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_subRack {SdrDeviceGroup_slot
long:
No} No}
[1..4294967295]
long:[1..2] long:[1..23]
Generated
automatically, it is
unnecessary to fill in
this column.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 36 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 37 页
ZTE中兴 内部公开▲
upperResumeLimit lowerResumeLimit
Alarm Recovery Upper Limit Alarm Recovery Lower Limit
long long
Specifies the value for clearing Specifies the value for clearing
an alarm raised when the an alarm raised when the
uppper environment threshold is actual value is below the lower
exceeded. The user can modify environment threshold. The
the value. user can modify the value.
R-W R-W
87 77
55 -20
70 -5
58 42
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 38 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rack
A,P long:[0..4095] long:[0..65535] No}
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 39 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_subRack {SdrDeviceGroup_slotN
long: long: [0..5]
No} o}
[1..4294967295] <default:0>
long:[1..2] long:[1..23]
Generated
automatically, it is
unnecessary to fill
in this column.
Primary Key Primary Key Primary Key R-I
1 1 1 1
1 1 2 2
1 1 1 1
1 1 2 2
1 3 1 0
1 3 2 1
1 3 3 2
1 3 4 3
1 3 5 4
1 3 6 5
1 1 1 1
1 1 2 2
1 1 1 1
1 1 2 2
1 1 1 1
1 1 2 2
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 40 页
ZTE中兴 内部公开▲
opticalModuleType
Type of Optical Model
1:1.25G,
2:2.5G,
3:3G,
6:6G
<default:1>
In stack mode, the default
values of FS(slot 3)
boardand optical port No.3
optical port No.4 and optical
port No.5 are 2.5G.
R-W-I
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 41 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 42 页
ZTE中兴 内部公开▲
ref1FiberDevice_subRack ref1FiberDevice_slotN
ref1FiberDevice_rackNo ref1FiberDevice_port
No o
Upper-level Rack No. of Upper-level SubRack Upper-level Slot No. Optical Port of
Previous Hop in No. of Previous Hop in of Previous Hop in Previous Hop in
Topology Structure Topology Structure Topology Structure Topology Structure
long: [1..201] long: [1..2] long: [1..8] long: [0..5]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 43 页
ZTE中兴 内部公开▲
ref2FiberDevice_subRack ref2FiberDevice_slotN
ref2FiberDevice_rackNo ref2FiberDevice_port
No o
Lower-level Rack No. Lower-level SubRack Lower-level Slot No. Optical Port of Next
of Next Hop in No. of Next Hop in of Next Hop in Hop in Topology
Topology Structure Topology Structure Topology Structure Structure
long: [1..201] long: [1..2] long: [1..8] long: [0..5]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 44 页
ZTE中兴 内部公开▲
long:
A,P long:[0..4095] long:[0..65535] long:[1..96]
[1..4294967295]
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill
in this column.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 45 页
ZTE中兴 内部公开▲
0:TMA,
3:A-TMA, long:
long: [10..30,255]
4:A-COM, long: [0..65535] [70..170,255]
<default:20>
5:ETMA, <default:255>
6:A-ETMA The unit for different TMA
types: A-TMA: 0.25dB, A-
COM: 0.5dB, TMA: 0.1dB,
ETMA: 0.1dB, A-ETMA:
A-TMA corresponds to
0.25dB.
AISG TMA;
{tmaType==0}[70..150],
A-COM corresponds to
{tmaType==3}[44..100],
AISG Combiner;
{tmaType==4}[0..14],
TMA corresponds to Unit: 0.1dB Unit: 0.1dB
{tmaType==5}[200..320],
common TMA; 255: invalid. 255: invalid.
{tmaType==6}[92..100],
ETMA corresponds to
65535:{Invalid}
high gain common TMA;
General value:
A-ETMA corresponds to
{tmaType==0}[120],
high gain AISG TMA.
{tmaType==3}[48],
{tmaType==4}[10],
{tmaType==5}[240],
R-I R-W-I R-I R-W-I
{tmaType==6}[96]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 46 页
ZTE中兴 内部公开▲
dlDelay ulDelay
Downlink
Uplink Delay
Delay
Unit: ns Unit: ns
R-W-I R-W-I
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 47 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rackN
A,P long:[0..4095] long:[0..65535] o}
long: [1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 48 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 49 页
ZTE中兴 内部公开▲
4: Level-1 VSWR
threshold long long long long
<default:4>
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 50 页
ZTE中兴 内部公开▲
1:4G+1U,
2:2G+2U,
1:UMTS, 1:UMTS, 1:UMTS, 3:4G+1L,
2:GSM, 2:GSM, 2:GSM, 4:2G+1L,
16:LTE 16:LTE 16:LTE 5:4G+2U,
255:Invalid
<default:255>
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 51 页
ZTE中兴 内部公开▲
powerOffSwitch
0:Close,
1:Open
<default:0>
R-W-I
0
0
0
0
0
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 52 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rackNo}
A,P long:[0..4095] long:[0..65535]
long: [1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 53 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 54 页
OMCSUBNET
ModInd SDRMEID rackNo
ID
Modify ManagedEleme
Subnet ID RU Rack No.
Indication nt ID
{SdrDeviceG
roup_rackNo
A,P long:[0..4095] long:[0..65535]
}
long: [1..201]
Same in an Unique in
A:Add, P:Pass
OMMB. subnetwork.
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 57 页
ZTE中兴 内部公开▲
0,
PaDevice.suppBand==1[1910.0..1990.0],
PaDevice.suppBand==2[1840.0..1920.0],
PaDevice.suppBand==3[1700.0..1795.0],
PaDevice.suppBand==4[1700.0..1765.0],
PaDevice.suppBand==5[814.0..859.0],
Generated PaDevice.suppBand==6[820.0..850.0],
automatically, it is PaDevice.suppBand==7[2490.0..2580.0],
unnecessary to fill in PaDevice.suppBand==8[870.0..925.0],
this column. PaDevice.suppBand==9[1739.9..1794.9]
Unit:MHz
The attribute is not open to the user.
When it is set to 0, the calculation if
automatically performed. In special cases
when this parameter needs modification,
you can contact ZTE personnel.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 58 页
ZTE中兴 内部公开▲
long:
A,P long:[0..4095] long:[0..65535] string
[1..4294967295]
it is necessary to Unit:metre
Unique in fill in this column. The height of an
A:Add, P:Pass Same in an OMMB.
subnetwork. Base station code antenna above
starts from 1,2,3… sea level.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 59 页
ZTE中兴 内部公开▲
double: [- double: [-
string string
90.000000..90.000000] 180.000000..180.000000]
Unit:degree
Unit:metre
Unit:metre The longitude of the
The latitude of the
The elevation in meters antenna location based The pattern name is a
antenna location based
above sea level at the on World Geodetic textual, alpha-numeric
on World Geodetic
base of the antenna System (1984 version) string to allow identification
System (1984 version)
structure. This value, when global reference frame of the antenna pattern
global reference frame
subtracted from height, (WGS 84). Positive along with the antenna
(WGS 84). Positive
provides the height of the values correspond to vendor information such as
values correspond to the
antenna above the ground. degrees east of 0 model number, etc.
northern hemisphere.
degrees longitude.
R-W R-W R-W R-W
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 60 页
ZTE中兴 内部公开▲
1:Omnidirectional
Diversity,
string string:[0..3600]
2:Panel Diversity,
3:Sectorized Diversity
Unit:metre
Distance between The 3 dB power
antennas in the beamwidth of the
same sector (space antenna pattern in the
diversity case), vertical plane.
measured in meters.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 61 页
ZTE中兴 内部公开▲
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill
in this column.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 62 页
ZTE中兴 内部公开▲
refTxDevice_rack
dlAttenuation ulAttenuation dlDelay ulDelay
No
Downlink Downlink Connected Tx
Uplink Attenuation Uplink Delay
Attenuation Delay RU Rack No.
4
2
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 63 页
ZTE中兴 内部公开▲
ref1RxDevice_rack
refTxDevice_port refMechanicalAnt refRet refTma_tmaNo
Connected No
Connected Tx Connected RET Connected TMA Connected Rx RU
Mechanical Antenna
Port Antenna RDN Device Rack No.
RDN
long:
long:[1..5] long:[1..4294967295] long: [1..96] long:[1..201]
[1..4294967295]
Configure as "RetId"
It is valid when
of Ret object..
connection type is 1,
It is valid when
2, and 3. Base station It is valid when
It is valid when connection type is 1, It is valid when
code starts from connection type
connection type 2, and 3. The connection type is
1,2,3… The connected is 2, and 3. TMA
is 1, and 3. connected ANT and 2, and 3.
ANT and RET are ID and TMA exist.
RET are mutually
mutually excluded.
excluded.
R R R R R
2 2
1 3 3
4 3
1 5 4
1 1 2
6 4
1 7 5
8 5
1 9 6
10 6
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 64 页
ZTE中兴 内部公开▲
R R R R R
2
1
2
1
1
2
1
2
1
2
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 65 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 66 页
ZTE中兴 内部公开▲
refSdrDeviceGroup_subRac
dataProcessMode refSdrDeviceGroup_rackNo
kNo
Connected Board Rack Connected Board
Data Processing Mode
No. SubRack No.
0:Transparent transmission,
long: [1..201] long:[1..2]
1:Parse
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 67 页
ZTE中兴 内部公开▲
refSdrDeviceGroup_slot
No
Connected Board Slot
No.
long: [1..23]
R-I
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 68 页
ModInd OMCSUBNETID SDRMEID rackNo subRackNo
Modify
Subnet ID ManagedElement ID Rack No. SubRack No.
Indication
{SdrDeviceGroup_r {SdrDeviceGroup_subRack
A,P long:[0..4095] long:[0..65535] ackNo} No}
long: [1..201] long:[1..2]
Unique in
A:Add, P:Pass
subnetwork.
Return To Index Primary Key Primary Key Primary Key Primary Key
16 10 2 1
16 10 3 1
16 10 4 1
16 10 5 1
16 10 6 1
slotNo switchStatus voltage
Slot No. Switch Status Voltage
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 71 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_subRack {SdrDeviceGroup_slot
long: long: [0..5]
No} No}
[1..4294967295] <default:0>
long:[1..2] long: [1..23]
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 72 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 73 页
ZTE中兴 内部公开▲
upperLimitPercent switchStatus
Over Current Alarm
Switch State
Threshold Percent
0:Close,
long: [100,120..180]
1:Open
<default:120>
<default:1>
R-W-I R-W-I
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 74 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 75 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 76 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 77 页
ZTE中兴 内部公开▲
antImbResumeThreshol
antImbAlarmThreshold
d
Ant Imbalance Alarm Ant Imbalance
Threshold Resume Threshold
long:[1..14] long:[1..14]
Unit: db Unit:db
General value:10 General vlaue:10
R-W R-W
10 10
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 78 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rackNo}
A,P long:[0..4095] long:[0..65535]
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 79 页
ZTE中兴 内部公开▲
1:RETC,
17:MULTI_RET,
3:ATMA,
1:1.1,
long: 2:MULTI_TMA,
string:[1..32] string:[0..128] 2:2.0
[1..4294967295] 241:ACOM,
<default:1>
226:AETMA,
209:NSNRET,
210:LGPTMA
When LMT/OMCB
When LMT/OMCB
actively configures When LMT/OMCB
actively configures the
Generated the device type or actively configures the
device type or the
automatically, it is the reported device device type or the
reported device type is
unnecessary to fill type is scanned, reported device type is
scanned, the user fills
in this column. the user selects the scanned, the user fills
in the AISG version
type of devices as in the vendor code.
number.
needed.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 80 页
ZTE中兴 内部公开▲
255:Invalid.
Indicates the Indicates the
The AISG1.1 and
Indicates the superior local channel,
AISG2.0 Single RET Specifies the
user-defined channel, used used for
decives are invalid. connected RET
description. for SDTMA SDTMA
For other AISG2.0 device.
Cannot use the device of NSN device of NSN
devices, each subunit The connected RET
invalid characters, private private
number corresponds and TMA are
e.g. < > & ' protocol. The protocol. The
to an AISG device mutually excluded.
" \ / : ? # % @ , value for other value for other
that can be controlled
devices is 0. devices is 0.
separately.
R-I R-W R-I R-I R
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 81 页
ZTE中兴 内部公开▲
refTma_tmaNo
Connected TMA
Device No.
long:[1..96]
Specifies the
connected TMA
control unit.
The connected
TMA and RET
are mutually
excluded.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 82 页
ZTE中兴 内部公开▲
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 83 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 84 页
ZTE中兴 内部公开▲
{SdrDeviceGroup_rac
A,P long:[0..4095] long:[0..65535] kNo}
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
Return To Index Primary Key Primary Key Primary Key
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 85 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 86 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 87 页
ZTE中兴 内部公开▲
Queue Priority 1 Queue Priority 2 Queue Priority 3 Queue Priority 4 Queue Priority 5
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 88 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 89 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 90 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 91 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 92 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 93 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 94 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 95 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 96 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 97 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 98 页
ZTE中兴 内部公开▲
<本文中的所有信息均为中兴通讯股份有限公司内部信息,未经允许,不得外传> 共 529 页 , 第 99 页
ZTE中兴 内部公开▲
Modify
Subnet ID ManagedElement ID Rack No.
Indication
{SdrDeviceGroup_rac
A,P long:[0..4095] long:[0..65535] kNo}
long:[1..201]
Unique in
A:Add, P:Pass Same in an OMMB.
subnetwork.
{SdrDeviceGroup_subRac {SdrDeviceGroup_slot
kNo} No} long:[1..4294967295]
long:[1..2] long:[1..23]
Generated automatically,
it is unnecessary to fill in
this column.
Indicates whether to
open and enable the
Indicates the port
port. This item is
mode. The Upper-
invalid when the port
Port configuration of the board, united port connects to
is configured as
port functions vary with port type, RNC/BSC/CN, while
[backboard SGMII
including optical ports, electrical Cascade port connects
interface CC1
ports, and switching ports. to the subordinate
interface] or
SDR.
[backboard SGMII
General value:0
interface CC2
interface].
egressRateSwitc
operatingMode ingressRateSwitch ingressBitRate
h
Enable Egress
Enable Ingress Rate Ingress Rate
Link Mode Rate Limitation
Limitation or not Limit
or not
0:Self Negotiation,
1:Y, long: 1:Y,
6:100Mbps FDT,
0:N [560..1000000] 0:N
7:1000Mbps FDT,
<default:1> <default:1000> <default:0>
8:1000Mbps Self Negotiation
long: [70..250000]
long: [1..10] long: [1..10]
<default:250000>
Specifies a VLAN group ID for the Specifies a VLAN group ID for the current
current port. Port 6 (SGMII port CC1 port port. Port 6 (SGMII port CC1 port on the
Unit: kbps on the backplane) and port 7(SGMII port backplane) and port 7(SGMII port CC2
CC2 port on the backplane) can not be port on the backplane) can not be
configured in the same VLAN group. configured in the same VLAN group.
vlanMembership#6 vlanMembership#7
R-W-I R-W-I
ingressRateLimitMode
R-W-I
1: Y,
When smart0:power-saving
N string:[0..20] string:[0..20]
<default:0>
mode is started, the user
should configure power-
saving start time and end
time. During power-
saving, the mode will It is valid when starting It is valid when starting
block low guarantee local smart power-saving smart power-saving
cell, and the mode. The start time must mode. The end time must
corresponding baseband be not equal to the end be not equal to the start
board and PA will be time. time.
powered-down. It is an Format:HH:MM Format:HH:MM
energy saving and
consumption-reducing
strategy when the base
R-W-Iis free (tide
station service R-W R-W
0 effect). 0 0
Enable Bypass or
Negotiation entity ID type Enable UDPMUX Mode or not
not
0:Disable UdpMux,
1: IPv4 Address Type, 1:Y, 1:Enable Gsm and Umts UdpMux,
2: FQDN Type 0:N 2:Enable Gsm UdpMux,
<default:1> Enable bypass or not.
<default:0> 3:Enalbe Umts UdpMux
When daisy chain <default:0>
cascading is used, the
When UDPMUX mode is enabled,
upper level BBU
base station supports the function to
provides automatic
encapsulate multi-UDP packets into a
bridging function. If the
big packet to reduce the number of
upper level BBU is
Negotiate entity ID load packets and increase transmission
powered-down or
type. efficiency. If UDPMUX is disabled, the
abnormal, the E1
packages cann't be merged.
connected to
This attribute value should be
BSC/RNC can be
consistent with the RNC's, otherwise
transported to lower
UDP package will be lost.
level BBU. So it can
R-W-I reduce R-W-I
the influence R-W-I
1 0 range by faults. 0
long:[0..2]
A,P long:[0..4095] long:[0..65535] long: [1..3]
<default:0>
Generated
automatically
Unique in , it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary
to fill in this
column.
Return To Index Primary Key Primary Key Primary Key R-I
16 10 1 0
0:Master,
long:[0..63]
ipv4 1:Slave
<default:46>
<default:0>
refIpLayerConfig_ipNo refSaalUni_pvcNo
long:
long:[0..19]
[64490,64500..64516]
R R
0
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill in
this column.
Return To Index Primary Key Primary Key Primary Key R-I
16 10 1 Tcell
userLabel cePercent
Operator CE Percent(%) Associated to
Information An Operator
long:[0..100]
string: [0..127]
<default:0>
Cannot use the It is the percentage of the
invalid characters, operator in CE. The total of all
e.g. < > & ' the CE percentages is not
" \/: ? #%@, larger than 100%.
R-W R-I
0
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill in
this column.
Return To Index Primary Key Primary Key Primary Key Primary Key
mcc mnc
MCC MNC
string:[3..3] string:[2..3]
long: long:[0..17]
A,P long:[0..4095] long:[0..65535]
[1..4294967295] <default:0>
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill
in this column.
0:Self Negotiation,
0:RNC/BSC/CN,
1:Electrical port 10Mbps FDT,
1:SDR,
2:Electrical port 100Mbps FDT, long:[100..1000000]
2:Third-party
3:Optical port 1000Mbps FDT,
<default:0> Ethernet bearer is valid. Unit:
4:Optical port 100Mbps FDT
kbps.
{operatingMode==0}
Opposite network element
[100,1000000] step 100,
connected by the object.
{operatingMode==1}[100,10000]
In the case of base
step 100,
station cascading, set this
{operatingMode==2}[100,100000]
property of upper-level
step 100,
base station to be "SDR".
{operatingMode==3}
If its value is set as a Ethernet bearer is valid.
[100,1000000] step 100,
third-party device, it General value: 0.
{operatingMode==4}[100,100000]
indicates that the base
step 100
station provides the data
transmission channel for
General value:
the third-party device in
{operatingMode==0}[100000],
ATM+FE cascading
{operatingMode==1}[10000],
cases.
R-I R-W {operatingMode==2}[100000],
R-W
0 0 100000
{operatingMode==3}[100000],
0 {operatingMode==4}[100000]
1
13:SA,
5:SE,
long:[1..2] 14:SE, long: [0..7] long:[1..2]
1:TRB-G904/TRB-G184
etc.
E1 bearer used at
E1 bearer used at the port. E1 bearer used at the the port. It is used T1 bearer used at the port.
It is used in ATM port. It is used in ATM in ATM It is used in ATM
transmission mode or IP transmission mode or IP transmission transmission mode or IP
over PPP transmission over PPP transmission mode or IP over over PPP transmission
mode. mode. PPP transmission mode.
mode.
R R R R
1 13 0
1 13 5
refGeDevice_subRack refGeDevice_slotN
refT1Device_slotNo refT1Device_port
No o
Used T1 Board Slot Used Ethernet Board Used Ethernet
Used T1 Port ID
No. SubRack No. Board Slot No.
13:SA,
5:SE, long: [0..7] long:[1..2] long: [1..8]
14:SE,
T1 bearer used at
T1 bearer used at the the port. It is used
Ethernet used at
port. It is used in ATM in ATM Ethernet used at the
the port. It is used
transmission mode or transmission mode port. It is used in IP
in IP transmission
IP over PPP or IP over PPP transmission mode.
mode.
transmission mode. transmission
mode.
R R R R
1 1
refGeDevice_port
Used Ethernet
Board Port ID
long
R
0
DhcpRelayI
ModInd OMCSUBNETID SDRMEID dhcpRelayNo
d
Modify DHCP Relay
Subnet ID ManagedElement ID RDN
Indication No.
long: [0..3]
A,P long:[0..4095] long:[0..65535] long: [1..1]
<default:0>
Generated
automaticall
Unique in y, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessar
y to fill in
this column.
Return To Index Primary Key Primary Key Primary Key R-I
refPhyLayerPort_phyLayerPort refEthernetLink_ethernetLink
vid enableDhcpRelay
No No
Enable DHCP
Used Physical Port Used Ethernet Link VLAN ID Relay Function
or not
1:Y,
long:[0..17] long:[0..0] long: [1..4094] 0:N
<default:0>
R R R R-W-I
dhcpServerIp
DHCP Server
Address
IPV4
<default:0.0.0.
0>
R-W-I
AtmLayerLinkI
ModInd OMCSUBNETID SDRMEID atmLayerLinkNo
d
Modify
Subnet ID ManagedElement ID RDN ATM Layer Link No.
Indication
long:[0..11]
A,P long:[0..4095] long:[0..65535] long: [1..12]
<default:0>
Generated
automatically, it
Unique in
A:Add, P:Pass Same in an OMMB. is unnecessary
subnetwork.
to fill in this
column.
0:32cell,
0:IMA,
1:Y, 1:64cell,
1:TC long:[0..3]
0:N 2:128cell,
<default:0>
3:256cell
IMA protocol
parameter. It It is valid when
indicates whether protocol type of It is valid when
to enable the ATM layer is protocol type of
descrambling IMA. ATM layer is IMA.
Object protocol type
processing for the IMA group Frame length of
represented by MO. It must
cell net load. It number, which is IMA group. It must
be consistent with that at the
must be consistent unique within a be consistent with
opposite end.
with the network the configuration at
configuration at the element. the opposite end.
opposite end General value: General value: 2.
device. 0.
General value:0
R-I R-W R R-W
{refPhyLayerPort_phyLayerPortN {refPhyLayerPort_phyLayerPortN
1:ITC,
o#1} o#2}
2:CTC
long:[0..17] long:[0..17]
It is valid when
protocol type of
ATM layer is IMA.
Physical-layer port of IMA. If the Physical-layer port of IMA. If the
Clock mode of IMA
protocol type is TC, only one protocol type is TC, only one
group. It is
refPhyLayerPort port can be refPhyLayerPort port can be
recommended that
configured. If the protocolt type is configured. If the protocolt type is
it should be
IMA, all ports within the IMA IMA, all ports within the IMA
consistent with the
group are included. group are included.
configuration at the
opposite end.
General value: 1.
R-W R-W-I R-W-I
refPhyLayerPortNo#3 refPhyLayerPortNo#4
{refPhyLayerPort_phyLayerPortNo {refPhyLayerPort_phyLayerPortNo
#3} #4}
long:[0..17] long:[0..17]
R-W-I R-W-I
refPhyLayerPortNo#5 refPhyLayerPortNo#6
{refPhyLayerPort_phyLayerPortN
{refPhyLayerPort_phyLayerPortNo#5}
o#6}
long:[0..17]
long:[0..17]
R-W-I R-W-I
Physical-layer port of IMA. If the Physical-layer port of IMA. If the Physical-layer port of IMA. If the
protocol type is TC, only one protocol type is TC, only one protocol type is TC, only one
refPhyLayerPort port can be refPhyLayerPort port can be refPhyLayerPort port can be
configured. If the protocolt type is configured. If the protocolt type is configured. If the protocolt type is
IMA, all ports within the IMA group IMA, all ports within the IMA group IMA, all ports within the IMA group
are included. are included. are included.
Physical-layer port of IMA. If the Physical-layer port of IMA. If the Physical-layer port of IMA. If the
protocol type is TC, only one protocol type is TC, only one protocol type is TC, only one
refPhyLayerPort port can be refPhyLayerPort port can be refPhyLayerPort port can be
configured. If the protocolt type is configured. If the protocolt type is configured. If the protocolt type is
IMA, all ports within the IMA group IMA, all ports within the IMA group IMA, all ports within the IMA
are included. are included. group are included.
refPhyLayerPortNo#13 refPhyLayerPortNo#14
{refPhyLayerPort_phyLayerPortNo {refPhyLayerPort_phyLayerPortNo#
#13} 14}
long:[0..17] long:[0..17]
R-W-I R-W-I
TS-bit Mapping
Used ATM Port 15 Used ATM Port 16
Relation 0
It is valid when
{refPhyLayerPort_phyLayerPortNo {refPhyLayerPort_phyLayerPortNo#16 protocol type of
#15} } ATM layer
long: is TC.
[0..1]
long:[0..17] long:[0..17] E1 or T1 timeslot
used by TC. Each
bit within the
value range
represents a
Physical-layer port of IMA. If the Physical-layer port of IMA. If the timeslot. 0
protocol type is TC, only one protocol type is TC, only one indicates not
refPhyLayerPort port can be refPhyLayerPort port can be using the timeslot
configured. If the protocolt type is configured. If the protocolt type is IMA, while 1 indicates
IMA, all ports within the IMA group all ports within the IMA group are using the
are included. included. timeslot. For E1,
the timeslot
configured can be
1 ~ 31. For T1,
R-W-I R-W-I the R-W
timeslot
configured can be
1 ~ 24.
It must be fill in
with 0 or 1.
timeSlotBitMap# timeSlotBitMap#
timeSlotBitMap#2 timeSlotBitMap#5 timeSlotBitMap#6
3 4
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 1 Relation
It is 2
valid when Relation 3 Relation 4 Relation 5
It is valid when protocol type of It is valid when
protocol type of ATM layer is protocol type of It is valid when
It is valid when
ATM layer
long: is TC.
[0..1] long:TC.
[0..1] ATM layer
long: is TC.
[0..1] protocol type of
long: [0..1] long: [0..1]
protocol type of
E1 or T1 timeslot E1 or T1 E1 or T1 timeslot ATM layer is TC.
ATM layer is TC.
used by TC. timeslot used by used by TC. E1 or T1 timeslot
E1 or T1 timeslot
Each bit within TC. Each bit Each bit within used by TC. Each
used by TC. Each
the value range within the value the value range bit within the value
bit within the value
represents a range represents a range represents
range represents a
timeslot. 0 represents a timeslot. 0 a timeslot. 0
timeslot. 0
indicates not timeslot. 0 indicates not indicates not using
indicates not using
using the timeslot indicates not using the the timeslot while
the timeslot while 1
while 1 indicates using the timeslot while 1 1 indicates using
indicates using the
using the timeslot while 1 indicates using the timeslot. For
timeslot. For E1,
timeslot. For E1, indicates using the timeslot. For E1, the timeslot
the timeslot
the timeslot the timeslot. For E1, the timeslot configured can be
configured can be
configured can E1, the timeslot configured can 1 ~ 31. For T1, the
1 ~ 31. For T1, the
be 1 ~ 31. For configured can be 1 ~ 31. For timeslot
timeslot configured
T1, the timeslot
R-W be 1 R-W
~ 31. For T1, the timeslot
R-W configured
R-Wcan be R-W
can be 1 ~ 24.
configured can T1, the timeslot configured can 1 ~ 24.
It must be fill in
be 1 ~ 24. configured can be 1 ~ 24. It must be fill in
with 0 or 1
It must be fill in be 1 ~ 24. It must be fill in with 0 or 1
with 0 or 1. It must be fill in with 0 or 1
with 0 or 1
timeSlotBitMap#
timeSlotBitMap#7 timeSlotBitMap#9 timeSlotBitMap#10 timeSlotBitMap#11
8
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 6 Relation 7 Relation 8 Relation 9 Relation 10
It is valid when It is valid when
protocol type of protocol type of
It is valid when It is valid when It is valid when
long: [0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] long: [0..1] long: [0..1]
protocol type of protocol type of protocol type of
E1 or T1 timeslot E1 or T1 timeslot
ATM layer is TC. ATM layer is TC. ATM layer is TC.
used by TC. used by TC. Each
E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot
Each bit within bit within the
used by TC. Each used by TC. Each used by TC. Each
the value range value range
bit within the value bit within the value bit within the value
represents a represents a
range represents a range represents a range represents a
timeslot. 0 timeslot. 0
timeslot. 0 timeslot. 0 timeslot. 0
indicates not indicates not
indicates not using indicates not using indicates not using
using the timeslot using the timeslot
the timeslot while the timeslot while 1 the timeslot while 1
while 1 indicates while 1 indicates
1 indicates using indicates using the indicates using the
using the using the timeslot.
the timeslot. For timeslot. For E1, timeslot. For E1,
timeslot. For E1, For E1, the
E1, the timeslot the timeslot the timeslot
the timeslot timeslot
configured can be configured can be configured can be
configured can configured can be
1 ~ 31. For T1, the 1 ~ 31. For T1, the 1 ~ 31. For T1, the
be 1 ~ 31. For 1 ~ 31. For T1,
timeslot configured timeslot configured timeslot configured
R-W T1, the timeslot
R-W the R-W
timeslot R-W R-W
can be 1 ~ 24. can be 1 ~ 24. can be 1 ~ 24.
configured can configured can be
It must be fill in It must be fill in It must be fill in
be 1 ~ 24. 1 ~ 24.
with 0 or 1 with 0 or 1 with 0 or 1
It must be fill in It must be fill in
with 0 or 1 with 0 or 1
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 11 Relation 12 Relation 13 Relation 14 Relation 15
It is valid when It is valid when It is valid when
protocol type of protocol type of protocol type of
It is valid when It is valid when
long: [0..1] long: [0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1]
protocol type of ATM protocol type of ATM
E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot
layer is TC. layer is TC.
used by TC. used by TC. Each used by TC. Each
E1 or T1 timeslot E1 or T1 timeslot
Each bit within bit within the bit within the
used by TC. Each bit used by TC. Each bit
the value range value range value range
within the value within the value
represents a represents a represents a
range represents a range represents a
timeslot. 0 timeslot. 0 timeslot. 0
timeslot. 0 indicates timeslot. 0 indicates
indicates not indicates not indicates not
not using the not using the
using the using the timeslot using the timeslot
timeslot while 1 timeslot while 1
timeslot while 1 while 1 indicates while 1 indicates
indicates using the indicates using the
indicates using using the timeslot. using the timeslot.
timeslot. For E1, the timeslot. For E1, the
the timeslot. For For E1, the For E1, the
timeslot configured timeslot configured
E1, the timeslot timeslot timeslot
can be 1 ~ 31. For can be 1 ~ 31. For
configured can configured can be configured can be
T1, the timeslot T1, the timeslot
be 1 ~ 31. For 1 ~ 31. For T1, 1 ~ 31. For T1,
configured can be 1 configured can be 1
T1, the timeslot the R-W
timeslot the R-W
timeslot
~R-W
24. ~R-W
24. R-W
configured can configured can be configured can be
It must be fill in with It must be fill in with
be 1 ~ 24. 1 ~ 24. 1 ~ 24.
0 or 1 0 or 1
It must be fill in It must be fill in It must be fill in
with 0 or 1 with 0 or 1 with 0 or 1
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 16 Relation 17 Relation 18 Relation 19 Relation 20
It is valid when It is valid when It is valid when It is valid when It is valid when
protocol type of protocol type of protocol type of protocol type of protocol type of
ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1]
E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot
used by TC. Each used by TC. Each used by TC. Each used by TC. Each used by TC. Each
bit within the bit within the bit within the bit within the bit within the
value range value range value range value range value range
represents a represents a represents a represents a represents a
timeslot. 0 timeslot. 0 timeslot. 0 timeslot. 0 timeslot. 0
indicates not indicates not indicates not indicates not indicates not
using the timeslot using the timeslot using the timeslot using the timeslot using the timeslot
while 1 indicates while 1 indicates while 1 indicates while 1 indicates while 1 indicates
using the timeslot. using the timeslot. using the timeslot. using the timeslot. using the timeslot.
For E1, the For E1, the For E1, the For E1, the For E1, the
timeslot timeslot timeslot timeslot timeslot
configured can be configured can be configured can be configured can be configured can be
1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1,
the R-W
timeslot the R-W
timeslot the R-W
timeslot the R-W
timeslot the R-W
timeslot
configured can be configured can be configured can be configured can be configured can be
1 ~ 24. 1 ~ 24. 1 ~ 24. 1 ~ 24. 1 ~ 24.
It must be fill in It must be fill in It must be fill in It must be fill in It must be fill in
with 0 or 1 with 0 or 1 with 0 or 1 with 0 or 1 with 0 or 1
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 21 Relation 22 Relation 23 Relation 24 Relation 25
It is valid when It is valid when It is valid when It is valid when It is valid when
protocol type of protocol type of protocol type of protocol type of protocol type of
ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1]
E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot
used by TC. Each used by TC. Each used by TC. Each used by TC. Each used by TC. Each
bit within the bit within the bit within the bit within the bit within the
value range value range value range value range value range
represents a represents a represents a represents a represents a
timeslot. 0 timeslot. 0 timeslot. 0 timeslot. 0 timeslot. 0
indicates not indicates not indicates not indicates not indicates not
using the timeslot using the timeslot using the timeslot using the timeslot using the timeslot
while 1 indicates while 1 indicates while 1 indicates while 1 indicates while 1 indicates
using the timeslot. using the timeslot. using the timeslot. using the timeslot. using the timeslot.
For E1, the For E1, the For E1, the For E1, the For E1, the
timeslot timeslot timeslot timeslot timeslot
configured can be configured can be configured can be configured can be configured can be
1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1,
the R-W
timeslot the R-W
timeslot the R-W
timeslot the R-W
timeslot the R-W
timeslot
configured can be configured can be configured can be configured can be configured can be
1 ~ 24. 1 ~ 24. 1 ~ 24. 1 ~ 24. 1 ~ 24.
It must be fill in It must be fill in It must be fill in It must be fill in It must be fill in
with 0 or 1 with 0 or 1 with 0 or 1 with 0 or 1 with 0 or 1
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Relation 26 Relation 27 Relation 28 Relation 29 Relation 30
It is valid when
It is valid when It is valid when It is valid when It is valid when
protocol type of
protocol type of protocol type of protocol type of protocol type of
ATM layer is TC.
ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] ATM layer
long: is TC.
[0..1] long: [0..1]
E1 or T1
E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot E1 or T1 timeslot
timeslot used by
used by TC. Each used by TC. Each used by TC. Each used by TC. Each
TC. Each bit
bit within the bit within the bit within the bit within the
within the value
value range value range value range value range
range
represents a represents a represents a represents a
represents a
timeslot. 0 timeslot. 0 timeslot. 0 timeslot. 0
timeslot. 0
indicates not indicates not indicates not indicates not
indicates not
using the timeslot using the timeslot using the timeslot using the timeslot
using the
while 1 indicates while 1 indicates while 1 indicates while 1 indicates
timeslot while 1
using the timeslot. using the timeslot. using the timeslot. using the timeslot.
indicates using
For E1, the For E1, the For E1, the For E1, the
the timeslot. For
timeslot timeslot timeslot timeslot
E1, the timeslot
configured can be configured can be configured can be configured can be
configured can
1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1, 1 ~ 31. For T1,
be 1 ~ 31. For
the R-W
timeslot the R-W
timeslot the R-W
timeslot the R-W
timeslot R-W
T1, the timeslot
configured can be configured can be configured can be configured can be
configured can
1 ~ 24. 1 ~ 24. 1 ~ 24. 1 ~ 24.
be 1 ~ 24.
It must be fill in It must be fill in It must be fill in It must be fill in
It must be fill in
with 0 or 1 with 0 or 1 with 0 or 1 with 0 or 1
with 0 or 1
timeSlotBitMap#
32
TS-bit Mapping
Relation 31
It is valid when
protocol type of
ATM layer is TC.
long: [0..1]
E1 or T1
timeslot used by
TC. Each bit
within the value
range
represents a
timeslot. 0
indicates not
using the
timeslot while 1
indicates using
the timeslot. For
E1, the timeslot
configured can
be 1 ~ 31. For
T1, the R-W
timeslot
configured can
be 1 ~ 24.
It must be fill in
with 0 or 1
long:[1..50]
A,P long:[0..4095] long:[0..65535] long: [1..50]
<default:1>
refAtmLayerLink_atmLayerLink
pathId vpi vci
No
AAL2 Link ID VPI VCI Used ATM Layer Protocol
trafficProfile_serviceCatego
adminState
ry
Service Type Manual Operation Field
0:SRVC_CBR,
0:No Manual Operation,
1:SRVC_RTVBR,
1:Block,
2:SRVC_NRTVBR,
2:Disabled,
3:SRVC_UBR,
This attribute indicates the 4:Powered-down,
4:SRVC_ABR,
category of ATM services. 65536:Block Smoothly
5:SRVC_OTHER
All categories of ATM <default:0>
<default:0>
services can be divided
into two types: real-time
services (SRVC_CBR, and
SRVC_RTVBR), and non-
real-time services This field can not be
(SRVC_NRTVBR, configured. Do not modify
SRVC_UBR, SRVC_ABR, it.
and SRVC_OTHER). Real-
time services are generally
used for transporting voice
data and R-W-I
signalling data. R-W
Non-real-time services are
generally used for
transporting data services.
long:
A,P long:[0..4095] long:[0..65535] long: [1..18] [64490,64500..64516]
<default:64500>
AAL5 PVC link number.
When the AAL5 PVC link
bears IP services, the
value is 64516 or 64500.
Generated When the AAL5 PV link
automatically, it transparently transmits
Unique in
A:Add, P:Pass Same in an OMMB. is unnecessary data from third-party
subnetwork.
to fill in this devices, the value is
column. 64490.
When the AAL5 PV link
bears other services, the
Return To Index Primary Key Primary Key Primary Key value rangesR-Ifrom 64501
to 64515.
refAtmLayerLink_atmLayerLinkN
vpi vci trafficProfile_maxOutBitRate
o
Maximum Transmitting
VPI VCI Used ATM Layer Link
Bandwidth
{trafficProfile_maxEgressBitR
long: [0..255] long: [8..255] ate}
long:[0..11]
<default:0> <default:8> long: [0..30000]
<default:128>
trafficProfile_serviceCategor
trafficProfile_aveInBitRate trafficProfile_minInBitRate
y
Minimum Receiving
Average Receiving Bandwidth Service Type
Bandwidth
0:SRVC_CBR,
1:SRVC_RTVBR,
{trafficProfile_averageIngressBit {trafficProfile_minIngressBitR
2:SRVC_NRTVBR,
Rate} ate}
3:SRVC_UBR,
This attribute indicates the
long: [0..30000] long: [0..30000]
4:SRVC_ABR,
category of ATM services.
<default:128> <default:128>
5:SRVC_OTHER
All categories of ATM
<default:0>
services can be divided into
two types: real-time services
(SRVC_CBR, and
SRVC_RTVBR), and non-
real-time services
Unit: kbps. Unit: kbps. (SRVC_NRTVBR,
SRVC_UBR, SRVC_ABR,
and SRVC_OTHER). Real-
time services are generally
used for transporting voice
R-W-I R-W-I data and R-W-I
signalling data.
Non-real-time services are
generally used for
transporting data services.
refSaalUni_pvcNo
Used SaalUni Link
long:[64490,64500..64516]
R-I
Modify
Subnet ID ManagedElement ID RDN Bts Cascade Type
Indication
Base station
0:TSI,
A,P long:[0..4095] long:[0..65535] long:[1..4294967295] cascading type. It
1:ATM Routing
indicates how a
<default:0>
base station tranmits
data to the lower-
level base station. It
has nothing to do
with the upper-layer
data protocol.
Generated
Timeslot cross
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB. means mapping
subnetwork. unnecessary to fill in
from the timeslots of
this column.
input E1/T1 to the
timeslots of output
E1/T1 within the
base station. ATM
Return To Index Primary Key Primary Key Primary Key routing
R-Imeans
16 10 1 0forwarding the input
PVC not of the base
station according to
the configured route.
ingressTimeSlotBitMap#
btsCascadeNo ref1PhyLayerPortNo
1
TS-bit Mapping
BtsCascade No. Inlet E1
Relation (Inlet) 0
long:
{ref1PhyLayerPort_phyLayerPort
[0..100,65000..65059]
No} long: [0..1]
<default:0>
long:[0..17]
It is valid when cascade
type is TSI.
It describes which
timeslots in the ingress
E1/T1 are reserved for
It is valid when cascade type is
Link ID of timeslot cross the lower-level base
TSI.
in the TSI cascading stations. Each bit
E1 or T1 (ingress E1/T1) for
mode. Route number in corresponds to a
connecting RNC/BSC/CN used by
the ATM cascading timeslot. 0 indicates not
upper-level base station in the TSI
mode. reserved for the lower-
cascading mode.
level base station while 1
reserved for the lower-
level base station.
R-I R-W It must be fill in with 0
R-W
1 0 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
It is valid when cascade It is valid when cascade It is valid when cascade It is valid when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the ingress timeslots in the ingress timeslots in the ingress timeslots in the ingress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. level base station. level base station. level base station.
It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W It must be fill in with 0
R-W
0 or 1. 0 or 1. 0 or 1. 0 or 1.
{ref2PhyLayerPort_phyLayerPort
No} long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
long type is TSI. type is TSI.
It describes which It describes which
timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base
It is valid when cascade type is stations. Each bit stations. Each bit
TSI. corresponds to a corresponds to a
E1 or T1 (egress E1/T1) for timeslot. 0 indicates not timeslot. 0 indicates not
connecting SDR used by upper- reserved for the lower- reserved for the lower-
level base station in the TSI level base station while 1 level base station while 1
cascading mode. reserved for the lower- reserved for the lower-
level base station. It level base station. It
must be one-one must be one-one
corresponding to the corresponding to the
R-W R-W R-W
5 0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
egressTimeSlotBitMap#1
egressTimeSlotBitMap#7 egressTimeSlotBitMap#8 egressTimeSlotBitMap#9
0
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade
type is TSI. type is TSI. type is TSI. type is TSI.
It describes which It describes which It describes which It describes which
timeslots in the egress timeslots in the egress timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base the lower-level base the lower-level base
stations. Each bit stations. Each bit stations. Each bit stations. Each bit
corresponds to a corresponds to a corresponds to a corresponds to a
timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not timeslot. 0 indicates not
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station while 1 level base station while 1 level base station while 1 level base station while 1
reserved for the lower- reserved for the lower- reserved for the lower- reserved for the lower-
level base station. It level base station. It level base station. It level base station. It
must be one-one must be one-one must be one-one must be one-one
corresponding to the corresponding to the corresponding to the corresponding to the
R-W R-W R-W R-W
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
0 Itlower-level timeslots.
must be fill in with 0
or 1. or 1. or 1. or 1.
egressTimeSlotBitMap#3 egressTimeSlotBitMap#3
ingressVpi ingressVci
1 2
long:
It is valid [0..1]
when cascade long:
It is valid [0..1]
when cascade long: [0..255] long: [8..65535]
type is TSI. type is TSI.
It describes which It describes which
timeslots in the egress timeslots in the egress
E1/T1 are reserved for E1/T1 are reserved for
the lower-level base the lower-level base
It is valid when cascade It is valid when cascade
stations. Each bit stations. Each bit
type is ATM Routing. type is ATM Routing.
corresponds to a corresponds to a
Ingress VPI of the ATM Ingress VCI of the ATM
timeslot. 0 indicates not timeslot. 0 indicates not
route. It must be consistent route. It must be consistent
reserved for the lower- reserved for the lower-
with the RNC/BSC/CN with the RNC/BSC/CN
level base station while 1 level base station while 1
configuration. configuration. General
reserved for the lower- reserved for the lower-
General value: 0. value: 8.
level base station. It level base station. It
must be one-one must be one-one
corresponding to the corresponding to the
R-W R-W R R
0 Itlower-level timeslots.
must be fill in with 0
1 Itlower-level timeslots.
must be fill in with 0
or 1. or 1.
Used ATM Link Egress VPI Egress VCI Used Egress ATM Link
{ref1AtmLayerLink_atmLayerLin {ref2AtmLayerLink_AtmLayerLink
kNo} long: [0..255] long: [8..65535] No}
long:[0..11] long:[0..11]
It is valid when
It is valid when
cascade type
cascade type is
is ATM
ATM Routing.
It is valid when cascade type is Routing. It is valid when cascade type is
Egress VCI of
ATM Routing. Egress VPI of ATM Routing.
the ATM route.
Ingress PVC bottom-layer link the ATM route. Egress PVC bottom-layer link of
It must be
of the ATM route. It can only be It must be the ATM route. It can only be
consistent with
either IMA or TC. It must be consistent with either IMA or TC. It must be
the lower-level
consistent with the the lower-level consistent with the lower-level
SDR
RNC/BSC/CN configuration. SDR SDR configuration.
configuration
configuration.
General value:
General value:
8.
R 0.
R R R
It is valid when cascade type It is valid when cascade type is It is valid when cascade type
is ATM Routing. Unit: kbps. ATM Routing. Unit: kbps. is ATM Routing. Unit: kbps.
General value: 128. General value: 128. General value: 128.
It is valid when cascade type is It is valid when cascade type is ATM It is valid when cascade type
ATM Routing. Unit: kbps. Routing. Unit: kbps. General value: is ATM Routing. Unit: kbps.
General value: 128. 128. General value: 128.
trafficProfile_serviceCatego
destinationNodeBId
ry
0:SRVC_CBR,
1:SRVC_RTVBR,
It is valid when cascade
2:SRVC_NRTVBR,
type3:SRVC_UBR,
is ATM Routing. long: [0..65535]
This attribute indicates the
4:SRVC_ABR,
category of ATM services.
5:SRVC_OTHER
All categories of ATM
services can be divided into
two types: real-time
services (SRVC_CBR, and
SRVC_RTVBR), and non- It is valid when
real-time services cascade type is ATM
(SRVC_NRTVBR, Routing. General
SRVC_UBR, SRVC_ABR, value: 0.
and SRVC_OTHER). Real-
time services are generally
used for transporting voice
data and signalling data.
R-W R
Non-real-time services are
generally used for
transporting data services.
General value: 0.
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill in
this column.
refPhyLayerPort_phyLayerPortN
timeSlotBitMap#1 timeSlotBitMap#2 timeSlotBitMap#3 timeSlotBitMap#4
o
TS-bit Mapping TS-bit Mapping TS-bit Mapping TS-bit Mapping
Used IP Port
Relation 0 Relationt 1 Relationt 2 Relationt 3
It represents
long: [0..1]the It represents
long: [0..1]the It represents
long: [0..1]the It represents
long: [0..1]the
long:[0..17] E1/T1 timeslot E1/T1 timeslot E1/T1 timeslot E1/T1 timeslot
<default:0> <default:1> <default:1> <default:1>
used by the used by the used by the used by the
HDLC link. Each HDLC link. Each HDLC link. Each HDLC link. Each
bit of it represents bit of it represents bit of it represents bit of it represents
a timeslot. 0 a timeslot. 0 a timeslot. 0 a timeslot. 0
indicates not indicates not indicates not indicates not
using the timeslot using the timeslot using the timeslot using the timeslot
while 1 indicates while 1 indicates while 1 indicates while 1 indicates
R-I R-W-I
using the R-W-I
using the R-W-I
using the R-W-I
using the
0 0 timeslot. 1 timeslot. 1 timeslot. 1 timeslot.
long:[0..7]
A,P long:[0..4095] long:[0..65535] long:[1..4294967295]
<default:0>
Generated
Unique in automatically, it is
A:Add, P:Pass Same in an OMMB.
subnetwork. unnecessary to fill in
this column.
refHdlc_HdlcNo# protocolTyp
localIp mpCode mpClass ipCompress
16 e
PPP Long-short Support IP
Used HDLC Base Station
Encapsulat Sequence of MP MP Priority Compress or
Channel 16 IP
IP address of ion Type Head not
HDLC link that the base
IPV4 0: PPP, 2:Long sequence, 1: Y,
bears PPP. station. It is It indicates the It indicates
long:[0..15] <default:0.0.0. 1: ML-PPP 6:Short sequence, long: [1..4,255] 0: N
When the used
0> for <default:1> Long/short
255:Invalid number of whether
<default:0>the
protocol signaling and sequence format of priorities ML-PPP link
PPP
encapsulation service data the ML-PPP packet supported when supports the IP
encapsulati
type is PPP, only transmission in head. It it is ML-MC PPP is compression
on type. It
one HDLC can the IP network. different from that supported. When mode. If it is
must be
be configured. 0.0.0.0 at the opposite MC is supported, different from
consistent
When the indicates end, ML-PPP two bits in the that at the
with that at
protocol obtaining the automatically frame format are opposite end,
the opposite
encapsulation local IP performs used to represent ML-PPP
end.
type is ML-PPP,
R-W-I address
R-W-I R-I negotiation.
R-W the R-W
priority. automatically
R-W-I
at most 16 through
118.16.10.10 1 2 General value:2 4 255: invalid 0 performs
HDLCs can be negotiation General value:4 negotiation.
configured. with NE at the
opposite end.
isUsedToFECascad maxFragmentSiz
e e
Is Used to FE Maximun MP
Cascade or not Slicing Length
1: Y,
long:[64..512]
0: N
<default:128>
<default:0>
E1/T1+EthernetIt
indicates whether Maximun slicing
the PPP link is used size when
for cascading, and MLPPP is
the cascadig mode segmented.
is E1/T1+Ethernet.
R-W-I R-W-I
0 128
Generated
Same in an automatically, it is
A:Add, P:Pass Unique in subnetwork.
OMMB. unnecessary to fill in
this column.
refPhyLayerPort_phyLayerPortN
ethernetLinkNo mtu
o
Ethernet Link No. Used Physical Layer Port Unit:
MTU byte
It represents the
long:[0..0] long: [256..1800]
maximum number of
long:[0..17]
<default:0> <default:1500>
transmitted bytes of the
packet of each Ethernet
link layer. The larger it is,
the higher the bandwidth
One Ethernet physical port usage is. However, it
corresponds to one link. might cause the end-to-
end transmission delay
to increase. You can
adjust it according to the
R-I R-I actual condition
R-W-I to avoid
0 1 1500
the data packet being
segmented in
transmission.
long:[1..4094] long: [1..4094] long: [1..4094] long: [1..4094] long: [1..4094] long: [1..4094]
VLAN number VLAN number VLAN number VLAN number VLAN number VLAN number
contained in the contained in the contained in the contained in the contained in the contained in the
Ethernet frame. Ethernet frame. Ethernet frame. Ethernet frame. Ethernet frame. Ethernet frame.
This setting is This setting is This setting is This setting is This setting is This setting is
optional, and optional, and optional, and optional, and optional, and optional, and
you can set at you can set at you can set at you can set at you can set at you can set at
most eight most eight most eight most eight most eight most eight
numbers. numbers. numbers. numbers. numbers. numbers.
R R R R R R
298
vlanMembership vlanMembership
#7 #8
VLAN No.7 VLAN No.8
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill in
this column.
refPhyLayerPort_phyLayerPortN
ethernetOamRole ethernetOamTimeOut loopbackTimeOut
o
OAM Session Remote Loopback
Used Physical Layer Port EthernetOam Role Timeout Period Timeout Period
(second) (second)
0:PASSIVE,
long: [5..10] long: [1..10]
long:[0..17] 1:ACTIVE
<default:5> <default:5>
<default:0>
pduTransPeriod eventInfo_eventType#1
Interval of Packets
Event Type 1
Sent(100ms)
0:Errored frame second link
event,
long: [1..10]
1:Errored frame period link event,
<default:10>
2:Errored frame link event,
3:Errored symbol link event
R-W-I R-W
eventInfo_windowSize#1 eventInfo_threshold#1
long:[1..65535] long:[0..4294967295]
R-W R-W
eventInfo_eventType#2 eventInfo_windowSize#2
R-W R-W
eventInfo_threshold#2 eventInfo_eventType#3
Unit: times
{eventType==0}[1..900],
{eventType==1}[1..65535],
{eventType==2}[1..65535],
{eventType==3}
[1..4294967295]
R-W R-W
eventInfo_windowSize#3 eventInfo_threshold#3
long:[0..65535] long:[0..4294967295]
R-W R-W
eventInfo_eventType#4 eventInfo_windowSize#4
eventInfo_threshold#4
Threshold 4
long:[0..4294967295]
Unit: times
{eventType==0}[1..900],
{eventType==1}[1..65535],
{eventType==2}[1..65535],
{eventType==3}
[1..4294967295]
R-W
BandwidthCtrlRuleI
ModInd OMCSUBNETID SDRMEID ruleNo
d
Modify Bandwidth
Subnet ID ManagedElement ID RDN
Indication Control Rule ID
long:
A,P long:[0..4095] long:[0..65535] long:[1..6]
[1..4294967295]
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill
in this column.
refEthernetLink_ethernetLink
vid#1 vid#2 vid#3
No
long: long:
long:[0..0] long: [2..4094,65535]
[2..4094,65535] [2..4094,65535]
It indicates on
It indicates on which It indicates on which
which VLAN the
It indicates on which Ethernet VLAN the bandwidth VLAN the
bandwidth
link the bandwidth allocation allocation rule is bandwidth allocation
allocation rule is
rule is applied. It and applied. You can set it rule is applied. You
applied. You can
refPppLink are mutually only when can set it only when
set it only when
exclusive. refEthernetLink is refEthernetLink is
refEthernetLink is
enabled. enabled.
enabled.
R R R R
R R R R R
0:RNC, 0:RNC,
1:BSC, 1:BSC,
string:[0..127] string:[0..127]
2:OMC, 2:OMC,
3:EPC 3:EPC
It indicates for
which office
the bandwidth It indicates for
It indicates for which rule is It indicates for which which office the
operator the bandwidth rule allocated. If it operator the bandwidth rule bandwidth rule is
is allocated. If it is not set, it is not set, it is allocated. If it is not set, it allocated. If it is not
indicates that bandwidth indicates that indicates that bandwidth set, it indicates that
control is not implemented bandwidth control is not implemented bandwidth control
between operators. control is not between operators. is not implemented
implemented between offices.
between
offices.
R R R R
refOperator_operatorName
officeDirection#3 officeDirection#4 serviceType#1
#3
Office Direction
Operator 3 Office Direction 3 Service Type 1
4
1:2G CS,
2:2G PS,
3:Iub Common
Transport Channel,
4:RRC Connection,
5:R99
Conversational,
0:RNC, 0:RNC,
6:R99 Streaming,
1:BSC, 1:BSC,
string:[0..127] 7:R99 Interactive,
2:OMC, 2:OMC,
8:R99 Background,
3:EPC 3:EPC
9:HSPA
Conversational,
10:HSPA Streaming,
11:HSPA Interactive,
12:HSPA
Background,
13:SCTP
It indicates for
It indicates for It indicates for which
which office the
It indicates for which which office the service type the
bandwidth rule is
operator the bandwidth bandwidth rule is bandwidth rule is
allocated. If it is
rule is allocated. If it is not allocated. If it is allocated. If it is not
not set, it
set, it indicates that not set, it indicates set, it indicates that
indicates that
bandwidth control is not that bandwidth bandwidth control is
bandwidth
implemented between control is not not implemented
control is not
operators. implemented between service
implemented
between offices. types.
between offices.
R R R R
It indicates for which It indicates for which It indicates for which It indicates for which
service type the service type the service type the service type the
bandwidth rule is bandwidth rule is bandwidth rule is bandwidth rule is
allocated. If it is not set, allocated. If it is not set, allocated. If it is not set, allocated. If it is not set,
it indicates that it indicates that it indicates that it indicates that
bandwidth control is not bandwidth control is not bandwidth control is not bandwidth control is not
implemented between implemented between implemented between implemented between
service types. service types. service types. service types.
R R R R
It indicates for which It indicates for which It indicates for which It indicates for which
service type the service type the service type the service type the
bandwidth rule is bandwidth rule is bandwidth rule is bandwidth rule is
allocated. If it is not set, allocated. If it is not set, allocated. If it is not set, allocated. If it is not set,
it indicates that it indicates that it indicates that it indicates that
bandwidth control is not bandwidth control is not bandwidth control is not bandwidth control is not
implemented between implemented between implemented between implemented between
service types. service types. service types. service types.
R R R R
It indicates for which It indicates for which It indicates for which It indicates for which
service type the service type the service type the service type the
bandwidth rule is bandwidth rule is bandwidth rule is bandwidth rule is
allocated. If it is not set, allocated. If it is not set, allocated. If it is not set, allocated. If it is not set,
it indicates that it indicates that it indicates that it indicates that
bandwidth control is not bandwidth control is not bandwidth control is not bandwidth control is not
implemented between implemented between implemented between implemented between
service types. service types. service types. service types.
R R R R
refQosMap_QosMap
egressGBR egressMBR
No
Used Qos Mapping
Egress GBR Egress MBR
Parameter
R-I R-I R
IpLayerConfigI
ModInd OMCSUBNETID SDRMEID ipNo
d
Modify IP Parameter
Subnet ID ManagedElement ID RDN
Indication Link No.
long:[0..19]
A,P long:[0..4095] long:[0..65535] long: [1..20]
<default:0>
Generated
automatically,
it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to
fill in this
Primary Key Primary Key column.
Primary Key R-I
Return To Index
16 10 1 0
16 10 2 1
refPppLink_pppLink refQosMap_QosMapN
refEthernetLink_EthernetLinkNo vid
No o
Used Qos Mapping
Used PPP Link Used Ethernet Link VLAN ID
Parameter
Same as a
VLAN in
refEthernetLink
.
R R R R
0 0
0 298 1
staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#1 staticRoutes_networkMask#1
#1
Destination IP Address 1 Network Mask 1 Next Hop IP Address 1
staticRoutes_nextHopIpAddr
staticRoutes_routePriority#2 staticRoutes_ipAddress#3
#2
Next Hop IP Address 2 Route Priority 2 Destination IP Address 3
staticRoutes_nextHopIpAddr
staticRoutes_networkMask#3 staticRoutes_routePriority#3
#3
Network Mask 3 Next Hop IP Address 3 Route Priority 3
staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#4 staticRoutes_networkMask#4
#4
Destination IP Address 4 Network Mask 4 Next Hop IP Address 4
staticRoutes_nextHopIpAddr
staticRoutes_routePriority#5 staticRoutes_ipAddress#6
#5
Next Hop IP Address 5 Route Priority 5 Destination IP Address 6
staticRoutes_nextHopIpAddr
staticRoutes_networkMask#6 staticRoutes_routePriority#6
#6
Network Mask 6 Next Hop IP Address 6 Route Priority 6
staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#7 staticRoutes_networkMask#7
#7
Destination IP Address 7 Network Mask 7 Next Hop IP Address 7
staticRoutes_nextHopIpAddr
staticRoutes_routePriority#8 staticRoutes_ipAddress#9
#8
Next Hop IP Address 8 Route Priority 8 Destination IP Address 9
staticRoutes_nextHopIpAddr
staticRoutes_networkMask#9 staticRoutes_routePriority#9
#9
Network Mask 9 Next Hop IP Address 9 Route Priority 9
staticRoutes_networkMask#1 staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#10
0 #10
Destination IP Address 10 Network Mask 10 Next Hop IP Address 10
staticRoutes_networkMask#1
staticRoutes_routePriority#10 staticRoutes_ipAddress#11
1
Route Priority 10 Destination IP Address 11 Network Mask 11
staticRoutes_nextHopIpAddr
staticRoutes_routePriority#11 staticRoutes_ipAddress#12
#11
Next Hop IP Address 11 Route Priority 11 Destination IP Address 12
staticRoutes_networkMask#1 staticRoutes_nextHopIpAddr
staticRoutes_routePriority#12
2 #12
Network Mask 12 Next Hop IP Address 12 Route Priority 12
staticRoutes_networkMask#1 staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#13
3 #13
Destination IP Address 13 Network Mask 13 Next Hop IP Address 13
staticRoutes_networkMask#1
staticRoutes_routePriority#13 staticRoutes_ipAddress#14
4
Route Priority 13 Destination IP Address 14 Network Mask 14
staticRoutes_nextHopIpAddr
staticRoutes_routePriority#14 staticRoutes_ipAddress#15
#14
Next Hop IP Address 14 Route Priority 15 Destination IP Address 15
staticRoutes_networkMask#1 staticRoutes_nextHopIpAddr
staticRoutes_routePriority#15
5 #15
Network Mask 15 Next Hop IP Address 15 Route Priority 15
staticRoutes_networkMask#1 staticRoutes_nextHopIpAddr
staticRoutes_ipAddress#16
6 #16
Destination IP Address 16 Network Mask 16 Next Hop IP Address 16
staticRoutes_routePriority#16
Route Priority 16
long: [0..7]
R-W
long:[1..128]
A,P long:[0..4095] long:[0..65535] long:[1..128]
<default:1>
Generated
automatically, it
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. is unnecessary
to fill in this
column.
Return To Index Primary Key Primary Key Primary Key R-I
Encryption
IKE Policy Authentication Method in Hash
IKE Version Algorithm in IKE
Priority IKE Negotiation Algorithm
Negotiation
1:Pre-shared key
1:DES,
1:IKEV1, authentication, 1:MD5,
long:[0..127] 4:3DES,
2:IKEV2 3:X.509 certificate 2:SHA
<default:0> 6:AES-128
<default:1> authentication <default:2>
<default:1>
<default:1>
randomFunctionAlgorith
dhGroup ikeLife
m
Pseudo-random Diffie-Hellman
IKE SA Lifetime
Function Algorithm Group
Unit:s
IPSecTransformSetI
ModInd OMCSUBNETID SDRMEID transformSetNo
d
Modify IPSecTransform-Set
Subnet ID ManagedElement ID RDN
Indication Policy No.
long:[1..40]
A,P long:[0..4095] long:[0..65535] long:[1..40]
<default:1>
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill in
this column.
Return To Index Primary Key Primary Key Primary Key R-I
espEncryptionAlgorith
ipsecMode espAuthAlgorithm
m
ESP Authentication ESP Encryption
IPSec Mode
Algorithm Algorithm
Generated
automatically, it is {aclType==0}[1..48],
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill {aclType==1}[11..42]
in this column.
aclConfig_sourceIp#
aclType aclConfig_aclNo#1 aclConfig_sourceSubnetMask#1
1
Access Control
Access Rule Type Source Address 1 Source address Subnet Mask1
List Object ID 1
0:IPSec,
1:Package filter long:[1..48] ipv4 ipv4
<default:0>
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#1 0:bypass,
{aclConfig_minDestinationPort#1}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 2 Source Address 2 Source address Subnet Mask2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#2 0:bypass,
{aclConfig_minDestinationPort#2}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 3 Source Address 3 Source address Subnet Mask3
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#3 0:bypass,
{aclConfig_minDestinationPort#3}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 4 Source Address 4 Source address Subnet Mask4
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#4 0:bypass,
{aclConfig_minDestinationPort#4}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 5 Source Address 5 Source address Subnet Mask5
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#5 0:bypass,
{aclConfig_minDestinationPort#5}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 6 Source Address 6 Source address Subnet Mask6
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#6 0:bypass,
{aclConfig_minDestinationPort#6}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 7 Source Address 7 Source address Subnet Mask7
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#7 0:bypass,
{aclConfig_minDestinationPort#7}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 8 Source Address 8 Source address Subnet Mask8
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#8 0:bypass,
{aclConfig_minDestinationPort#8}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Access Control List Object ID 9 Source Address 9 Source address Subnet Mask9
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
{aclConfig_maxDestinationPort#9 0:bypass,
{aclConfig_minDestinationPort#9}
} 1:discard,
long:[0..65535]
long:[0..65535] 2:protect
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:1 General value:65535 General value:0
When access rule type is IPSec, When access rule type is IPSec, When access rule type is IPSec,
it should be configured, otherwise it should be configured, otherwise it should be configured, otherwise
it needn't. it needn't. it needn't.
General value:65535 General value:0 General value:2
Remote Network Mask Local Port Upper Bound Local Port Lower Bound
When access rule type is When access rule type is When access rule type is
package filter, it should be package filter, it should be package filter, it should be
configured, otherwise it configured, otherwise it configured, otherwise it
needn't. needn't. needn't.
General value:255.255.255.0 General value:0 General value:65535
R-W R-W R-W
aclForFilter_ruleProtoco
aclForFilter_minRemotePort aclForFilter_maxRemotePort
l
Remote Port Upper Bound Remote Port Lower Bound Filter Protocol No.
1:ICMP,
6:TCP,
long:[0..65535] long:[0..65535] 17:UDP,
132:SCTP,
255:ALL
When access rule type is When access rule type is When access rule type
package filter, it should be package filter, it should be is package filter, it
configured, otherwise it configured, otherwise it should be configured,
needn't. needn't. otherwise it needn't.
General value:0 General value:65535 General value:255
R-W R-W R-W
aclForFilter_ruleDirection aclForFilter_ruleAction
0:IP transmission
direction, 0:Pass,
1:IP receiving direction, 1:Discard
2:IP bi-direction
IPSecConfigI
ModInd OMCSUBNETID SDRMEID ipsecNo
d
Modify
Subnet ID ManagedElement ID RDN IPSec Config No.
Indication
long:[1..48]
A,P long:[0..4095] long:[0..65535] long:[1..48]
<default:1>
Generated
automatically
, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary
to fill in this
column.
Return To Index Primary Key Primary Key Primary Key R-I
policyGenerationLev
remoteAddr pfs byteLife timeLife
el
Remote IP Policy Generation
PFS Option Byte Life Time Life
Address Level
0:Default,
0:Disable PFS,
ipv4 1:Use,
1:MODP768, long: [2560..536870912] long: [120..86400]
<default:0.0. 2:Require,
2:MODP1024 <default:4608000> <default:56000>
0.0> 3:Unique
<default:0>
<default:3>
Used IKE Policy 2 Used IKE Policy 3 Used IKE Policy 4 Used IKE Policy 5
Joint configuration with Joint configuration with Joint configuration with Joint configuration with
refEthernetLink. refEthernetLink. refEthernetLink. refEthernetLink.
refIPSecTransformSetNo#1 refIPSecTransformSetNo#2
{refIPSecTransformSet_transformSetN {refIPSecTransformSet_transformSetN
o#1} o#2}
long:[1..40] long:[1..40]
R-W-I R-W-I
refIPSecTransformSetNo#3 refIPSecTransformSetNo#4
{refIPSecTransformSet_transformSetN {refIPSecTransformSet_transformSet
o#3} No#4}
long:[1..40] long:[1..40]
R-W-I R-W-I
refAccessControlList_acl
refIPSecTransformSetNo#5 refIPSecTransformSetNo#6
No
Used Access Control
Used Transform-set 5 Used Transform-set 6
List
{refIPSecTransformSet_transformSetN {refIPSecTransformSet_transformSetN
o#5} o#6} long:[1..48]
long:[1..40] long:[1..40]
0:HTTP,
long:
A,P long:[0..4095] long:[1..1] 1:HTTPS long:[0..19]
[0..65535]
<default:0>
Return To Index Primary Key Primary Key Primary Key R-W-I R-I
caServerIp caServerPath certificateName certificateExtension
Extended Option of
IP Address of Domain Name of Base
CA Server Path Base Station
CA Server Station Certificate
Certificate
ipv4
<default:0.0.0. string string string
0>
Enter the server side It is used to fill in the
It is used to fill in the
URL of CMP protocol extended option of
application subject (subject
(the remaining part with certificate
field value) of base station
IP address of host address and port application. The
certificate. The writing format
CA server. removed) according to writing format is
should meet the X.500
the CMP protocol "attribute
Standard. For example,
configuration of CA name=attribute
/C=CN/O=ZTE/CN=Nodeb01.
server. value;".
R-W-I R-W R-W R-W
caServerPort privateKeyLength controlValue
Private Key Control value of
Transport Layer
Length of Base certificate request
Port of CA Server
Station Certificate message
1024,
long:[1..65535]
2048 string
<default:80>
<default:1024>
Transport layer
port ID of CA The generated Enter CerRequest
server. Enter the private key length. information of CMP
option according to It can select 1024 protocol, according
the CA server or 2048, unit: bit. to CA/RA strategy.
configuration.
Modify
Subnet ID ManagedElement ID RDN
Indication
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill in
this column.
serviceDscpMap_cs2GDs serviceDscpMap_ps2GDs
qosMapNo enableSlaveFlag
cp cp
Enable Slave Flag or DSCP Value Associated DSCP Value Associated
Qos Mapping No.
not to 2G CS Service to 2G PS Service
long:[0..4294967295] 1:Y,
long: [0..63,255] long: [0..63,255]
<default:0> 0:N
This attribute indicates This attribute indicates
the DSCP value of 2G CS the DSCP value of 2G PS
domain services. The domain services. The
value 255 indicates the IP value 255 indicates the IP
link does not bear this link does not bear this
class of service. class of service.
General value:36 General value:20
R-I R-W R-W R-W
0 36 20
1 255 255
serviceDscpMap_rrcConn serviceDscpMap_r99ConverD
serviceDscpMap_commonTransChan
Dscp scp
DSCP Value Associated
DSCP Value Associated to Iub DSCP Value Associated to
to RRC Connection
common Transport Channel Service R99 Conversational Service
Service
{serviceDscpMap_commonTransChan
Dscp} long: [0..63,255] long: [0..63,255]
long: [0..63,255]
This attribute indicates the
This attribute indicates the
This attribute indicates the DSCP value DSCP value of R99
DSCP value of RRC. The
of common transport channel. The conversation services. The
value 255 indicates the IP
value 255 indicates the IP link does not value 255 indicates the IP link
link does not bear this
bear this class of service. does not bear this class of
class of service.
General value:46 service.
General value:36
General value:36
R-W R-W R-W
255 255 255
46 36 36
DSCP Value Associated to R99 DSCP Value Associated to R99 DSCP Value Associated to R99
Streaming Service Interactive Service Background Service
{serviceDscpMap_r99StreamingDsc {serviceDscpMap_r99InteractiveDs {serviceDscpMap_r99Background
p} cp} Dscp}
long: [0..63,255] long: [0..63,255] long: [0..63,255]
This attribute indicates the DSCP This attribute indicates the DSCP This attribute indicates the DSCP
value of R99 streaming services. value of R99 interactive services. value of R99 background services.
The value 255 indicates the IP link The value 255 indicates the IP link The value 255 indicates the IP link
does not bear this class of service. does not bear this class of service. does not bear this class of service.
General value:36 General value:20 General value:0
serviceDscpMap_hspaConverD
serviceDscpMap_hspaStreaming serviceDscpMap_hspaInteractive
scp
DSCP Value Associated to DSCP Value Associated to HSPA DSCP Value Associated to HSPA
HSPA Conversational Service Streaming Service Interactive Service
{serviceDscpMap_hspaStreamingDs {serviceDscpMap_hspaInteractiveDs
long: [0..63,255] cp} cp}
long: [0..63,255] long: [0..63,255]
This attribute indicates the
DSCP value of HSPA This attribute indicates the DSCP This attribute indicates the DSCP
conversation services. The value of HSPA streaming services. value of HSPA interactive services.
value 255 indicates the IP link The value 255 indicates the IP link The value 255 indicates the IP link
does not bear this class of does not bear this class of service. does not bear this class of service.
service. General value:255 General value:22
General value:38
R-W R-W R-W
255 255 255
38 255 22
dscpCosMap_dscp#64 dscpCosMap_cos#64
DSCP 64 COS 64
R-W R-W
long:[0..3]
A,P long:[0..4095] long:[0..65535] long: [1..4]
<default:0>
Generated
automatically,
it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary
to fill in this
column.
Return To Index Primary Key Primary Key Primary Key R-I
16 10 1 0
16 10 2 1
refIpLayerConfig_ipNo# refIpLayerConfig_ipNo
localPort remoteAddr#1
1 #2
Local Port ID Used IP 1 Remote Address 1 Used IP 2
long:[0..65535]
long:[0..19] ipv4 long:[0..19]
<default:0>
UMTS: 0..65535
GSM: 1..65534
Configure as IP link No. Configure as IP link
When radio mode is
"ipNo" of IpLayerConfig No. "ipNo" of
GSM, local port ID
object. IpLayerConfig object.
should be
BtsFunction's siteId.
R-I R-I R-I R-I
10 0 118.16.1.1
155 1 10.220.221.3
refIpLayerConfig_ipN refIpLayerConfig_ipN
remoteAddr#2 remoteAddr#3 remoteAddr#4
o#3 o#4
Remote Remote Remote
Used IP 3 Used IP 4
Address 2 Address 3 Address 4
Number of incoming
IP service model
and outgoing streams
configuration. You
of SCTP. At most six
can choose different
incoming and
model according to
outgoing streams can
the actual scenario.
be configured.
R-I R-I R-I
14596 6 46
155 2 46
EthernetCfmMdI
ModInd OMCSUBNETID SDRMEID mdNo
d
Modify
Subnet ID ManagedElement ID RDN MD No.
Indication
long:[0..7]
A,P long:[0..4095] long:[0..65535] long: [1..8]
<default:0>
Generated
It begins from
automatically, it
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. 0, and must be
is unnecessary to
unique.
fill in this column.
Return To Index Primary Key Primary Key Primary Key R-I
refPhyLayerPort_phyLayerPort
mdIndex mdLevel mdName
No
MD Index ID Used Physical Port MD Level MD Name
long:[1..8] long:[0..7]
long:[0..17] string:[0..43]
<default:1> <default:0>
This base station belongs to an
It begins from Ethernet port of the MD. At
1, and must present, only the Iub/Abis
be unique. interface of CC board can be
used.
R-I R-I R-W-I R
EthernetCfmM
ModInd OMCSUBNETID SDRMEID mdNo
aId
Modify
Subnet ID ManagedElement ID MD No. RDN
Indication
{EthernetCfmMd_mdNo}
A,P long:[0..4095] long:[0..65535] long: [1..4]
long:[0..7]
Generated
automatically,
The data should be set as
it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. MD No. of
unnecessary
EthernetCfmMd object.
to fill in this
column.
Return To Index Primary Key Primary Key Primary Key Primary Key
refEthernetLink_ethernetLinkN
maNo maIndex vid maName
o
ccmPeriod
3:100ms,
4:1s,
5:10s,
6:1min,
7:10min
<default:3>
CCM detection period. If the
CCM message from the
opposite end is not received
after 3.5 times of the period,
the link is considered
abnormal.
R-W-I
EthernetCfmMpI
ModInd OMCSUBNETID SDRMEID maNo
d
Modify
Subnet ID ManagedElement ID MA No. RDN
Indication
{EthernetCfmMa_maNo}
A,P long:[0..4095] long:[0..65535] long: [1..32]
long:[0..31]
Generated
The data should be set as automatically, it
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. MA No. of EthernetCfmMa is unnecessary
object. to fill in this
column.
Return To Index Primary Key Primary Key Primary Key Primary Key
localMEPConfig_localLeve
mpNo mpIndex mepFullNetNo mepType
l
MP No. MP Index ID MEP Full Net No. MEP Type Local MEP Level
1:Local MEP,
long:[0..255] long: [1..32] long: [1..8191]
2:Remote MEP long: [0..7]
<default:0> <default:1> <default:1>
<default:1>
MEP number
(MEPId). It is set
It begins from It begins from
by the user, and It is valid when MPE type
0, and must be 1, and must
must be unique is set as local MEP.
unique. be unique.
within the MA
range.
localMEPConfig_almLowestLev remoteMEPConfig_localMPInd
remoteMEPConfig_remMEPMacAddr
el ex
Lowest Alarm Level Associated Local MP Index MAC Address of Remote MEP
{localMEPConfig_alarmLowestL {remoteMEPConfig_remoteMEPMacA
evel} long: [1..32] ddr}
long: [1..5] string
enableCCMDetect
Enable CCM Detection or not
1:Y,
0:N
If MEP <default:0>
type is local MEP,
enabling the CCM detection
means that the local end
performs multicast CCM
detection. If MEP type is remote
MEP, enabling the CCM
detection means that the local
end performs unicast CCM
detection for the remote end.
The current version only
supports multicast CCM
detection.
R-I
long:[1..10]
A,P long:[0..4095] long:[0..65535] long: [1..10]
<default:1>
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill
in this column.
ipv4 long:[0..63]
long:[0..19]
<default:0.0.0.0> <default:46>
1:Y,
long:[100..100000] long:[100..100000] long:[3..255]
0:N
Detection mode: multi-hop <default:300> <default:300> <default:5>
<default:0>
detection or single-hop
detection. For direct
connection, set it to N (single-
Unit: ms Configure BFD
hop detection). If there are Unit: ms
Configure minimum conversation
other switching devices in the Configure minimum packet
packet receiving detection time
connection, set it to Y (multi- transmitting interval,
interval, supported by accumlator. This
hop detection). expected by local end.
local end. This value is value is determined
If the BFD detection mode is This value is determined
determined upon both upon both ends'
multi-hop detection, only one upon both ends'
ends' negotiation. negotiation. Once this
multi-hop BFD can be negotiation. Once this
Once this value is value is changed, it
configured for one IP address. value is changed, it will
changed, it will cause will cause BFD
When and only when the BFD cause BFD session to be
BFD session to be session to be
detection mode is single-hop negotiated again.
negotiated again. negotiated again.
detection, the R-I
local IP address R-W-I R-W-I R-W-I
and the remote IP address are
configured at the same
network segment.
bfdAuthority_authorityTy bfdAuthority_authorityKeyI
bfdAuthority_authorityKeyValue
pe d
Authentication type Authentication Key ID Authentication Key
0:Not support
authentication,
1:Simple Password,
2:Keyed MD5,
3:Meticulous Keyed long:[1..255] string:[39..79]
MD5,
4:Keyed SHA1,
5:Meticulous Keyed
SHA1
Config authentication key. There are 20
values in tatal and each value range is
[0..255]. The values seperates by '.'.
This attribute indicates This attribute indicates the
(1)When Authentication type is 1,Valid
the BFD authority type. It ID of the authority key. It is
Authentication key is the first 5 values;
is a parameter for a parameter for
(2)When Authentication type is 2 or 3,Valid
interconnection. interconnection.
Authentication key is the first 16 values;
General value:1 General value:1
General
value:0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.0.
0
R-W R-W R-W
long:[1..32]
A,P long:[0..4095] long:[0..65535] long: [1..32]
<default:1>
Generated
Link priority
automatically, it
configuration of IP
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. is unnecessary
clock, cannot be
to fill in this
duplicate.
column.
Return To Index Primary Key Primary Key Primary Key R-I
dscp
DSCP
long:[0..63]
<default:46>
R-I
long:[0..65535] long:[0..50]
A,P long:[0..4095] long:[0..65535]
<default:0> <default:0>
It represents
the
transmission
power sharing
NodeB ID. It is
ratio of all
an
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. local cells in a
interconnection
PA. All PAs
parameter.
within the
same NodeB
use this
value.
Return To Index Primary Key Primary Key R-W-I R-W-I
16 10 155 0
1: Y,
long:[0, 3..60] long:[1..3840, 65535] long:[1..3840, 65535]
0: N
<default:0> <default:65535> <default:65535>
<default:0>
0:Invalid
Unit: minute
The parameter indicates the
65535: invalid 65535: invalid
requirement period for NodeB to
It represents the It represents the
detect RNC audit. It will switch to
maximum amount of maximum amount of
standby RNC if no audit
CEs available for the CEs available for the
requirement from active RNC is
uplink of NodeB. downlink of NodeB.
received within the period. 0
indicates no standby RNC
exists.
R-W-I R-W-I R-W-I R-W-I
1 0 192 192
hsdpaSpi#1 hsdpaSpi#2
hsdpaSpi#3 hsdpaSpi#4 hsdpaSpi#5 hsdpaSpi#6 hsdpaSpi#7
HSDPA SPI HSDPA SPI HSDPA SPI
HSDPA SPI 0 HSDPA SPI 1 HSDPA SPI 5 HSDPA SPI 6
2 3 4
long:
long: [1..2000] long: [1..2000] long: [1..2000] long: [1..2000] long: [1..2000]
[1..2000]
It is the
<default:36> It<default:43>
is the weight <default:62> <default:74> <default:89>
<default:52>
weight
corresponding
It is the weight correspondin It is the weight
to the 16 It is the weight
corresponding g to the 16 corresponding It is the weight
priorities corresponding
to the 16 priorities to the 16 corresponding
(SPI0 ~ to the 16
priorities (SPI0 (SPI0 ~ priorities (SPI0 to the 16
SPI15) in priorities (SPI0
~ SPI15) in SPI15) in ~ SPI15) in priorities (SPI0 ~
HSDPA ~ SPI15) in
HSDPA HSDPA HSDPA SPI15) in
scheduling. HSDPA
scheduling. scheduling. scheduling. HSDPA
The larger the scheduling. The
The larger the The larger the The larger the scheduling. The
weight is, the larger the
weight is, the weight is, the weight is, the larger the weight
easier the weight is, the
easier the easier the easier the is, the easier the
scheduling is. easier the
scheduling is. scheduling is. scheduling is. scheduling is. In
In scheduling is. In
In In In configuration, it
configuration, configuration, it
configuration, it configuration, configuration, it is required that
it is required is required that
is required
R-W-I that R-W-I it isR-W-I
required R-W-I < is required
R-W-I that hsdpaSpi[n]
R-W-I <
that hsdpaSpi[n]
36hsdpaSpi[n] < 43
hsdpaSpi[n] <
52 that 62
hsdpaSpi[n+1].
74
hsdpaSpi[n] < 89
hsdpaSpi[n+1].
hsdpaSpi[n+1]. hsdpaSpi[n] < hsdpaSpi[n+1].
hsdpaSpi[n+1]
hsdpaSpi[n+1
.
].
long: [1..2000] long: [1..2000] long: [1..2000] long: [1..4096] long: [1..4096] long: [1..4096]
<default:107> <default:128> <default:154> <default:1> <default:2> <default:3>
It is the weight It is the weight
It is the weight
corresponding It is the weight corresponding It is the weight
corresponding
to the 16 corresponding to the 16 corresponding
It is the weight to the 16
priorities (SPI0 to the 16 priorities (SPI0 to the 16
corresponding to priorities (SPI0
~ SPI15) in priorities (SPI0 ~ SPI15) in priorities (SPI0
the 16 priorities ~ SPI15) in
HSDPA ~ SPI15) in HSUPA ~ SPI15) in
(SPI0 ~ SPI15) HSDPA
scheduling. HSUPA scheduling. HSUPA
in HSDPA scheduling.
The larger the scheduling. The larger the scheduling.
scheduling. The The larger the
weight is, the The larger the weight is, the The larger the
larger the weight weight is, the
easier the weight is, the easier the weight is, the
is, the easier the easier the
scheduling is. easier the scheduling is. easier the
scheduling is. In scheduling is.
In scheduling is. In scheduling is.
configuration, it In
configuration, In configuration, In
is required that configuration,
it is required configuration, it it is required configuration, it
hsdpaSpi[n] < it is required
R-W-I R-W-I that
R-W-I is required
R-W-I that that
R-W-I is required
R-W-I that
hsdpaSpi[n+1]. that
107 128
hsdpaSpi[n] <
154
hsdpaSpi[n] < 1hsupaSpi[n] < 2hsupaSpi[n] < 3hsupaSpi[n] <
hsdpaSpi[n+1] hsupaSpi[n+1]. hsupaSpi[n+1] hsupaSpi[n+1].
hsdpaSpi[n+1].
. .
hsupaSpi#1
hsupaSpi#4 hsupaSpi#5 hsupaSpi#6 hsupaSpi#7 hsupaSpi#8
hsupaSpi#9
0
HSUPA SPI HSUPA SPI
HSUPA SPI 3 HSUPA SPI 4 HSUPA SPI 5 HSUPA SPI 6 HSUPA SPI 7
8 9
long:
long: [1..4096] long: [1..4096] long: [1..4096] long: [1..4096] long: [1..4096]
[1..4096]
It is the
<default:11> It<default:12>
is the weight <default:13> <default:14> <default:16>
It is the weight It is the weight <default:15>
weight It is the weight
corresponding
corresponding It is the weight corresponding correspondin corresponding
to the 16
to the 16 corresponding to the 16 g to the 16 to the 16
priorities
priorities (SPI0 to the 16 priorities (SPI0 priorities priorities (SPI0
(SPI0 ~
~ SPI15) in priorities (SPI0 ~ SPI15) in (SPI0 ~ ~ SPI15) in
SPI15) in
HSUPA ~ SPI15) in HSUPA SPI15) in HSUPA
HSUPA
scheduling. HSUPA scheduling. HSUPA scheduling.
scheduling.
The larger the scheduling. The larger the scheduling. The larger the
The larger the
weight is, the The larger the weight is, the The larger the weight is, the
weight is, the
easier the weight is, the easier the weight is, the easier the
easier the
scheduling is. easier the scheduling is. easier the scheduling is.
scheduling is.
In scheduling is. In scheduling is. In
In
configuration, In configuration, In configuration,
configuration,
it is required configuration, it it is required configuration, it is required
it is required
that
R-W-I R-W-I is required
R-W-I that that
R-W-I it isR-W-I
required that
R-W-I
that
11
hsupaSpi[n] < 12
hsupaSpi[n] <
13
hsupaSpi[n] < 14 hsupaSpi[n] < 15 that 16
hsupaSpi[n] <
hsupaSpi[n+1] hsupaSpi[n+1]. hsupaSpi[n+1] hsupaSpi[n] < hsupaSpi[n+1]
hsupaSpi[n+1]
. . hsupaSpi[n+1 .
.
].
adminState
Manual Operation
Field
0:No Manual
Operation,
1:Block,
2:Disabled,
4:Powered-down,
65536:Block
Smoothly
<default:0>
R-W
0
ID of the opposite-
end RNC connected
Generated
with the Iub link. It
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. identifies with which
unnecessary to fill in
RNC IubLink is
this column.
connected. You may
not set it.
Return To Index Primary Key Primary Key Primary Key R-W
16 10 1
iubLinkClass
Class of Iub Link
0:Master,
1:Slave
<default:0>
Active/standby
class of the Iub
link. It helps users
to distinguish the
active Iub link and
the standby Iub
link.
R-I
0
Generated
Configure as class of
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. Iub link "iubLinkClass"
unnecessary to fill
of IubLink object.
in this column.
Return To Index Primary Key Primary Key Primary Key Primary Key
refOperator_operatorName# refOperator_operatorNa
refUdp_ipNo refAal2_pvcNo
1 me#2
Used UDP Used AAL2 Operator 1 Operator 2
Configure as IP link
No. "ipNo" of
IpLayerConfig object.
R R R-I R-I
refOperator_operatorNam
e#3
Operator 3
string:[0..127]
R-I
NbapCSignalling
ModInd OMCSUBNETID SDRMEID iubLinkClass
Id
Modify
Subnet ID ManagedElement ID Class of Iub Link RDN
Indication
{IubLink_iubLinkClas
A,P long:[0..4095] long:[0..65535] s} long: [1..4]
long:[0..1]
Generated
Configure as class of
automatically, it
Iub link
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. is unnecessary
"iubLinkClass" of
to fill in this
IubLink object.
column.
Return To Index Primary Key Primary Key Primary Key Primary Key
16 10 0 1
NbapDSignallingI
ModInd OMCSUBNETID SDRMEID iubLinkClass
d
Modify
Subnet ID ManagedElement ID Class of Iub Link RDN
Indication
{IubLink_iubLinkClass}
A,P long:[0..4095] long:[0..65535] long: [1..24]
long:[0..1]
Generated
Configure as class of
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. Iub link "iubLinkClass"
unnecessary to fill
of IubLink object.
in this column.
Return To Index Primary Key Primary Key Primary Key Primary Key
16 10 0 1
Modify
Subnet ID ManagedElement ID RDN Sector ID
Indication
long:[0..255]
A,P long:[0..4095] long:[0..65535] long:[1..30]
<default:0>
Generated
automatically, it
A sector ID must
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. is unnecessary
be unique.
to fill in this
column.
refTxDevice_rackN refTxDevice_por
userLabel band txType
o#1 t#1
Used Tx Device Used Tx Device
Sector Name Band Tx Type
Rack No.1 Port No.1
1:2.1G(Band I),
2:1900M(Band II),
0:No Diversity,
3:1800M(Band III),
2:2-RRU NOT DIV,
4:AWS(Band IV),
5:3-RRU NOT DIV,
5:850M(Band V),
string:[0..199] 3:4-RRU NOT DIV, long:[2..201] long:[1..5]
6:850M(Band VI),
4:5-RRU NOT DIV,
7:2.6G(Band VII),
7:6-RRU NOT DIV,
8:900M(Band VIII),
8:MIMO
9:1800M(Band IX)
<default:1>
refTxDevice_rackNo# refTxDevice_rackNo#
refTxDevice_port#2 refTxDevice_port#3
2 3
Used Tx Device Used Tx Device Port Used Tx Device Used Tx Device Port
Rack No.2 No.2 Rack No.3 No.3
RU No. RU No.
Select the RF Select the RF
transmissin device transmissin device
according to the according to the
configured configured
transmission type. transmission type.
The frequency bands The frequency bands
of all selected RF of all selected RF
devices must be devices must be
consistent. consistent.
refTxDevice_rackNo# refTxDevice_rackNo#
refTxDevice_port#4 refTxDevice_port#5
4 5
Used Tx Device Used Tx Device Port Used Tx Device Used Tx Device Port
Rack No.4 No.4 Rack No.5 No.5
RU No. RU No.
Select the RF Select the RF
transmissin device transmissin device
according to the according to the
configured configured
transmission type. transmission type.
The frequency bands The frequency bands
of all selected RF of all selected RF
devices must be devices must be
consistent. consistent.
refTxDevice_rackNo# refTxDevice_rackNo#
refTxDevice_port#6 refTxDevice_port#7
6 7
Used Tx Device Used Tx Device Port Used Tx Device Used Tx Device Port
Rack No.6 No.6 Rack No.7 No.7
RU No. RU No.
Select the RF Select the RF
transmissin device transmissin device
according to the according to the
configured configured
transmission type. transmission type.
The frequency bands The frequency bands
of all selected RF of all selected RF
devices must be devices must be
consistent. consistent.
refTxDevice_rackNo# refTxDevice_rackNo#
refTxDevice_port#8 refTxDevice_port#9
8 9
Used Tx Device Used Tx Device Port Used Tx Device Used Tx Device Port
Rack No.8 No.8 Rack No.9 No.9
RU No. RU No.
Select the RF Select the RF
transmissin device transmissin device
according to the according to the
configured configured
transmission type. transmission type.
The frequency bands The frequency bands
of all selected RF of all selected RF
devices must be devices must be
consistent. consistent.
refTxDevice_rackNo# refTxDevice_rackNo#
refTxDevice_port#10 refTxDevice_port#11
10 11
Used Tx Device Used Tx Device Port Used Tx Device Used Tx Device Port
Rack No.10 No.10 Rack No.11 No.11
RU No. RU No.
Select the RF Select the RF
transmissin device transmissin device
according to the according to the
configured configured
transmission type. transmission type.
The frequency bands The frequency bands
of all selected RF of all selected RF
devices must be devices must be
consistent. consistent.
refTxDevice_rackNo# refRxDevice_rackNo
refTxDevice_port#12 rxType
12 #1
Used Tx Device Used Tx Device Port Used Rx Device
Rx Type
1:No Diversity,
Rack No.12 No.12 Rack No.1
2:Diversity,
9:2-RRU NOT DIV,
4:2-RRU DIV,
11:3-RRU NOT DIV,
6:3-RRU DIV,
long:[2..201] long:[1..5] 8:4-RRU NOT DIV, long:[2..201]
3:4-RRU DIV,
10:5-RRU NOT DIV,
5:5-RRU DIV,
12:6-RRU NOT DIV,
7:6-RRU DIV,
13:MIMO
Uplink signal receiving
RU No.
type, such as whether RU No.
Select the RF
the receiving diversity is Select the RF
transmissin device
supported and the receiving device
according to the
receiving diversity type. according to the
configured
You can set the receiving type. The
transmission type.
receiving type frequency bands of
The frequency bands
according to the actual all selected RF
of all selected RF
application scenario devices must be
devices must be
and the configured consistent.
consistent.
transmissin type.
RU No.
RU No.
Select the RF
Select the RF
receiving device
receiving device
according to the
according to the
receiving type. The
receiving type. The
frequency bands of
frequency bands of all
all selected RF
selected RF devices
devices must be
must be consistent.
consistent.
RU No.
RU No.
Select the RF
Select the RF
receiving device
receiving device
according to the
according to the
receiving type. The
receiving type. The
frequency bands of
frequency bands of all
all selected RF
selected RF devices
devices must be
must be consistent.
consistent.
RU No.
RU No.
Select the RF
Select the RF receiving
receiving device
device according to the
according to the
receiving type. The
receiving type. The
frequency bands of all
frequency bands of all
selected RF devices
selected RF devices
must be consistent.
must be consistent.
RU No.
RU No.
Select the RF
Select the RF receiving
receiving device
device according to the
according to the
receiving type. The
receiving type. The
frequency bands of all
frequency bands of all
selected RF devices
selected RF devices
must be consistent.
must be consistent.
RU No. RU No.
Select the RF receiving Select the RF receiving
device according to the device according to the
receiving type. The receiving type. The
frequency bands of all frequency bands of all
selected RF devices selected RF devices
must be consistent. must be consistent.
refRxDevice_rackNo#1 refRxDevice_port#
2 12
Used Rx Device Rack Used Rx Device
No.12 Port No.12
long:[2..201] long:[1..5]
RU No.
Select the RF receiving
device according to the
receiving type. The
frequency bands of all
selected RF devices
must be consistent.
R-W R-W
{Usector_sectorId
A,P long:[0..4095] long:[0..65535] } long:[1..4294967295]
long:[0..255]
Generated
Configure as
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. sector ID of
unnecessary to fill in
Usector.
this column.
Return To Index Primary Key Primary Key Primary Key Primary Key
16 10 0 1
16 10 1 1
isAutoAssignBasebandResou
localCellId userLabel coverageType
rce
Local Cell Coverage Automatically Assign
Local Cell ID
Description Type Baseband Resource or not
0:Indoor, 1:Y,
long:[0..268435455]
string:[0..199] 1:Outdoor 0:N
<default:0>
<default:1> <default:1>
It sets whether to
automatically allocate the
baseband resource
It is an Cannot use the (BpDevice) for the local cell. If
interconnection invalid it is set to "Y", the system
parameter, and characters, e.g. automatically allocates the
must be consistent < > & ' " \ / : ? baseband resource for the
with that of RNC. #%@, local cell. If it is set to "N", the
user allocates the baseband
resource according to the
actual requirement.
50: 5M,
48: 4.8M,
46: 4.6M,
long: [1..2] long: [4..8] 44: 4.4M, double
42: 4.2M,
38: 3.8M
<default:50>
USector.band==1{[2110.0..2170.0]},
USector.band==2{[1930.0..1990.0]},
USector.band==3{[1805.0..1880.0]},
USector.band==4{[2110.0..2155.0]},
USector.band==5{[869.0..894.0]},
Format: subRack No.
USector.band==6{[875.0..885.0]},
It configures the
USector.band==7{[2620.0..2690.0]},
baseband resource
USector.band==8{[925.0..960.0]},
allocated for the local cell.
USector.band==9{[1884.9..1979.9]}
If the baseband resource
Unit: MHz.
is automatically allocated, Format: slot No.
General value:
this parameter needs not
USector.band==1{[2110.0]},
be configured; otherwise,
USector.band==2{[1930.0]},
at least one baseband
USector.band==3{[1805.0]},
board should be
USector.band==4{[2110.0]},
allocated.
USector.band==5{[869.0]},
USector.band==6{[875.0]},
USector.band==7{[2620.0]},
USector.band==8{[925.0]},
R-I R-I R-W-I USector.band==9{[1884.9]}
R-W-I
50 2157.4
50 2157.4
2500: 2.5km,
5000: 5km,
10000: 10km,
0:0-250km/h, 20000: 20km,
long: [-63..63]
double 1:250-350km/h 40000: 40km,
<default:0>
<default:0> 80000: 80km,
USector.band==1{[1920.0..1980. 120000: 120km,
0]}, 240000: 240km
USector.band==2{[1850.0..1910. <default:5000>
0]},
Uplink receiving
USector.band==3{[1710.0..1785.
range of the
0]},
local cell. If it is
USector.band==4{[1710.0..1755.
increased, the
0]},
uplink searching
USector.band==5{[824.0..849.0]}, Terminal
range of the cell Unit: chip.
USector.band==6{[830.0..840.0]}, moving rate
is also It is used to adjust the
USector.band==7{[2500.0..2570. supported by
increased. If it is downlink channel delay
0]}, the local cell. If
decreased, the of the cell and the
USector.band==8{[880.0..915.0]}, it is set to
searching range uplink search window
USector.band==9{[1749.9..1784. 1:250-350km/h,
of the cell is also position.
9]} more uplink
decreased. If it is increased, the
Unit: MHz. access
When search window is
General value: resource will be
performing the pushed farther.
USector.band==1{[1920.0]}, used.
adjustment,
USector.band==2{[1850.0]},
make sure that it
USector.band==3{[1710.0]},
matches the
USector.band==4{[1710.0]},
pilot power of
USector.band==5{[824.0]},
the cell.
USector.band==6{[830.0]},
R-W-I R-W-I R-W-I R-W-I
USector.band==7{[2500.0]},
1967.4 0 5000 0
USector.band==8{[880.0]},
1967.4
USector.band==9{[1749.9]}
0 5000 0
0: Enable,
long: [-63..63] long:[1..200, 255] 1: Y, 1: Y,
1: Disable
<default:0> <default:255> 0: N 0: N
<default:0>
Unit: W.
Maximum
transmission power
of the local cell. It
must be larger than
Unit: chip. or equal to the
It sets whether the E-
It is used to adjust transmission power
VAM function is
the uplink channel configured for RNC. It can be set as
It indicates enabled when the
delay of the cell and The sum of "Y" only when Tx
whether HSUPA VAM function is
the uplink search transmission power type of affiliated
supports TTI of supported. If E-VAM is
window position. of all local cells that sector is MIMO.
2ms. disabled, the common
If it is increased, the the same RU power General value: 0.
VAM function is used.
search window is amplifier bears must
General value: 0.
pushed farther. be smaller than the
rated power
(PaDevice.powewr).
255 indicates not
configuring the
maximum power.
R-W-I R-W-I R-W-I R-W-I R-W-I
0 255 0 0 0
0 255 0 0 0
refOperator_operatorNa
enableEnergySaving enableDynCode adminState
me
Enable Electric- Enable Dynamic Manual Operation
Quoted Operator
saving Mode or not Code or not Field
reserveParamter30
Reserve parameter
30
long
R-W
ref1ULocalCell_localCellId ref2ULocalCell_localCellId
1:Y,
long: [1..65534]
A,P long:[0..4095] long:[0..65535] 0:N
<default:1>
<default:0>
0:Auto, 0:Auto,
long: [1..5]
1:Manual 1:Manual
<default:5>
<default:0> <default:1>
It sets whether to perform automatic changeback
or manual changeback to change from the standby
Unit: minute
link to the active link. It is valid when the super
It is the timer of waiting
base station function is enabled. When the base
for automatic
It sets whether to station is working on the standby link, if the active
changeover. It is valid
enable the manual link is normal, the link changeback falls into the
only when the working
active/standby link following three cases:
link of the base station is
changeover 1. If the standby link is faulty, the system
faulty. If the working link
function. If it is set to automatically performs changeback to the active
is faulty, the base station
"Auto", the link after the autoSwitchTimer timer expires.
waits for the interval of
active/standby link 2. If the standby link is normal and this parameter
the timer, and
changeover cannot is set to "Auto", the system automatically performs
automatically performs
be initiated changeback to the active link after the
the
automatically from autoSwitchBackTimer timer expires.
changeover/changeback.
the NMS. 3. If the standby link is normal and this parameter
The timer is invalid when
is set to "Manual", the system manually performs
the manual changeover
R-W-I R-W-I the changeback operation,
R-W-I and immediately
is performed.
0 5 1 changes back to the active link after the manual
operation is completed.
autoSwitchBackTimer adminState
Auto Switch Back
Manual Operation Field
Timer
0:No Manual Operation,
1:Block,
long: [5..10] 2:Disabled,
<default:10> 4:Powered-down,
65536:Block Smoothly
<default:0>
Unit: minute
It sets the automatic
This field can not be
changeback timer. It
configured. Do not modify
is valid when the
it.
super base station
function is enabled.
R-W-I R-W
10 0
long:
A,P long:[0..4095] long:[0..65535] long:[0..2147483647]
[1..4294967295]
ID of the opposite-
Generated end BSC connected
automatically, it is with the Abis link. It
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill identifies with which
in this column. BSC AbisLink is
connected.
Return To Index Primary Key Primary Key Primary Key R-W
16 10 1
abisLinkClass
Class of Abis Link
0:Master,
1:Slave
<default:0>
R-I
0
refOperator_operatorName refOperator_operatorName
BtsMId refSctp_sctpNo
#1 #2
RDN Used SCTP Operator 1 Operator 2
refOperator_operatorName
#3
Operator 3
string:[0..127]
R-I
long: long:[0..15]
A,P long:[0..4095] long:[0..65535]
[1..4294967295] <default:0>
Generated
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork.
unnecessary to fill
in this column.
refPppLink_PppLink
direction destinationIp#1 destinationIp#2
No
Destination IP Destination IP
Direction Used PPP
Address 1 Address 2
0:UPLINK,
ipv4
1:DOWNLINK long:[0..7] ipv4
<default:0.0.0.0>
<default:0>
It sets whether the packet
forwarded by the base station
is uplink (can reach BSC Destination IP
according to the topology) or address of the
(cannot reach BSC according packet forwarded by
to the topology) downlink. the base station.
This parameter is related to
the network topology.
R-W-I R-I R-W-I R-W-I
GCellEquipmentFunction
ModInd OMCSUBNETID SDRMEID
Id
Modify
Subnet ID ManagedElement ID RDN
Indication
Generated automatically,
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. it is unnecessary to fill in
this column.
gsmCarrierConfig_IntlgtOff#2 gsmCarrierConfig_TimeSlotOff#2
{gsmCarrierConfig_enableIntelligentOff# {gsmCarrierConfig_enableTimeSlotOf
2} f#2}
1:Y, 1:Y,
0:N 0:N
The set is valid for RU02 and RU02E The set is valid for RU02 and RU02E
boards. General value: 0. boards. General value: 0.
R-W R-W
0 0
0 0
Set the carrier power. The sum Set the carrier power. The sum
of all the carrier power on a RU of all the carrier power on a RU
RF device should be smaller RF device should be smaller
than the rated power. Unit: W. than the rated power. Unit: W.
gsmCarrierConfig_gsmCarrier#6 gsmCarrierConfig_carrierPw#6
{gsmCarrierConfig_gsmCarrierN {gsmCarrierConfig_carrierPower
o#6} #6}
long:[6..6] long:[0..140]
<default:6> <default:0>
R-W R-W
Modify
Subnet ID ManagedElement ID RDN Cell No.
Indication
long: long:[1..54]
A,P long:[0..4095] long:[0..65535]
[1..4294967295] <default:1>
It represents the
GSM cell ID. You
can set it within
Generated
the value range.
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. A GSM cell ID
unnecessary to fill in
must be unique.
this column.
It is an
interconnection
Return To Index Primary Key Primary Key Primary Key parameter.
R-I
16 10 1 2
16 10 2 1
refGCellEquipmentFunctionNo
gpsOffset carrierNum#1 hsrCellOutInletFlag#1
#1 It is applied in the
GPS Synchronized Used GSM Cell Channel Used Carrier scenario
End ID 1 ofof High-
high
Frame Head Offset Resource 1 Number 1 speed railways
speed Railway Cell
configured with mutli-
GPS synchronization
carrier combination
frame number offset. {refGCellEquipmentFunction_g group. It1:Y,
is used to
You long:[0..50]
can set it within CellEquipmentFuncNo#1} long:[1..6]
<default:0> identify0:N
whether a
the value range. In a long:[1..216] It represents the <default:0>
channel is the
synchronization area, number of carriers
Channel resource used in the inlet/outlet endpoint
it is recommended to used for the cell on
cell. A cell can use multiple of the mutli-carrier
set different offsets for each channel. It
channel resources. You can combination. Each
different cells, which should correspond
configure carrierNum to set the cell can be configured
helps avoid the to the configuration
nubmer of carriers used in the with two endpoint
decrease in sequence of
channel resource. channels at most.
measurement refGCellEquipment
The configuration
efficiency of mobile
R-W-I R-W-I Function.
R-W-I R-W-I
sequency of this
0phone due to SCHs in 3 2 0 prameters must
0the cell broadcasting 1 5 0 correspond to the
simultaneously.
configuration
sequence of
refGCellEquipmentFu
nction.
hsrCellOutInletFlag#
It is applied in the refGCellEquipmentFunctionN
refGCellEquipmentFunctionNo#2 carrierNum#2
scenario 2 of high o#3
Used GSM Cell Channel Used Carrier Endspeed
ID 2railways
of High- Used GSM Cell Channel
Resource 2 Number 2 configured
speed Railway with
Cell Resource 3
mutli-carrier
combination group.
{refGCellEquipmentFunction_gCe It represents It is used to identify {refGCellEquipmentFunction_
1:Y,
llEquipmentFuncNo#2} long:[1..6]
the number of whether 0:Na channel is gCellEquipmentFuncNo#3}
long:[1..216] carriers used the inlet/outlet long:[1..216]
Channel resource used in the for the cell on endpoint of the Channel resource used in the
cell. A cell can use multiple each channel. mutli-carrier cell. A cell can use multiple
channel resources. You can It should combination. Each channel resources. You can
configure carrierNum to set the correspond to cell can be configure carrierNum to set
nubmer of carriers used in the the configured with two the nubmer of carriers used
channel resource. configuration endpoint channels in the channel resource.
sequence of at most. The
R-W-I R-W-I R-W-I R-W-I
refGCellEquip configuration
mentFunction. sequency of this
prameters must
correspond to the
configuration
sequence of
refGCellEquipmentF
unction.
hsrCellOutInletFlag#
It is applied in the refGCellEquipmentFunctionNo
carrierNum#3 carrierNum#4
scenario 3 of high #4
Used Carrier Endspeed
ID 3railways
of High- Used GSM Cell Channel Used Carrier
Number 3 configured
speed Railway with
Cell Resource 4 Number 4
mutli-carrier
combination group.
It is used to identify {refGCellEquipmentFunction_g It represents the
1:Y,
long:[1..6]the
It represents whether0:N a channel CellEquipmentFuncNo#4} long:[1..6]
number of
number of is the inlet/outlet long:[1..216] carriers used for
carriers used for endpoint of the Channel resource used in the the cell on each
the cell on each mutli-carrier cell. A cell can use multiple channel. It
channel. It should combination. Each channel resources. You can should
correspond to the cell can be configure carrierNum to set the correspond to
configuration configured with two nubmer of carriers used in the the
sequence of endpoint channels channel resource. configuration
refGCellEquipme at most. The sequence of
R-W-I R-W-I R-W-I R-W-I
ntFunction. configuration refGCellEquipm
sequency of this entFunction.
prameters must
correspond to the
configuration
sequence of
refGCellEquipmentF
unction.
refGCellEquipmentFunctionNo
hsrCellOutInletFlag#4 carrierNum#5 hsrCellOutInletFlag#5
It is applied in the #5
scenario
End ID 4 ofof High-
high Used GSM Cell Channel Used Carrier It is applied
End ID 5 of in the
High-
speed railways
speed Railway Cell Resource 5 Number 5 scenario of high
speed Railway Cell speed
configured with mutli- railways configured
carrier combination with mutli-carrier
group. It1:Y,
is used to {refGCellEquipmentFunction_g It represents combination 1:Y,group. It is
identify0:N
whether a CellEquipmentFuncNo#5} long:[1..6]
the number of used to identify
0:N
channel is the long:[1..216] carriers used whether a channel is
inlet/outlet endpoint of Channel resource used in the for the cell on the inlet/outlet endpoint
the mutli-carrier cell. A cell can use multiple each channel. It of the mutli-carrier
combination. Each cell channel resources. You can should combination. Each cell
can be configured configure carrierNum to set the correspond to can be configured with
with two endpoint nubmer of carriers used in the the two endpoint channels
channels at most. The channel resource. configuration at most. The
configuration sequence of configuration sequency
R-W-I R-W-I R-W-I R-W-I
sequency of this refGCellEquipm of this prameters must
prameters must entFunction. correspond to the
correspond to the configuration sequence
configuration of
sequence of refGCellEquipmentFun
refGCellEquipmentFu ction.
nction.
refGCellEquipmentFunctionNo# refGCellEquipmentFunctionN
carrierNum#6 hsrCellOutInletFlag#6
6 It is applied in the o#7
Used GSM Cell Channel Used Carrier scenario
End ID 6 ofof High-
high Used GSM Cell Channel
Resource 6 Number 6 speed railways
speed Railway Cell Resource 7
configured with mutli-
carrier combination
{refGCellEquipmentFunction_g group. It1:Y,
is used to {refGCellEquipmentFunction_
CellEquipmentFuncNo#6} long:[1..6]the
It represents identify0:N
whether a gCellEquipmentFuncNo#7}
long:[1..216] number of carriers channel is the long:[1..216]
Channel resource used in the used for the cell inlet/outlet endpoint of Channel resource used in the
cell. A cell can use multiple on each channel. the mutli-carrier cell. A cell can use multiple
channel resources. You can It should combination. Each channel resources. You can
configure carrierNum to set the correspond to the cell can be configured configure carrierNum to set
nubmer of carriers used in the configuration with two endpoint the nubmer of carriers used in
channel resource. sequence of channels at most. The the channel resource.
refGCellEquipmen configuration
R-W-I R-W-I R-W-I R-W-I
tFunction. sequency of this
prameters must
correspond to the
configuration
sequence of
refGCellEquipmentFu
nction.
refGCellEquipmentFunctionNo#1
carrierNum#9 hsrCellOutInletFlag#9
0
End ID 9 of High-speed Railway Used GSM Cell Channel
Used Carrier Number 9
Cell Resource 10
refGCellEquipmentFunctionNo#1
carrierNum#10 hsrCellOutInletFlag#10
1
End ID 10 of High-speed Used GSM Cell Channel
Used Carrier Number 10
Railway Cell Resource 11
refGCellEquipmentFunctionNo#1
carrierNum#11 hsrCellOutInletFlag#11
2
End ID 11 of High-speed Used GSM Cell Channel
Used Carrier Number 11
Railway Cell Resource 12
refGCellEquipmentFunctionNo#1
carrierNum#12 hsrCellOutInletFlag#12
3
End ID 12 of High-speed Used GSM Cell Channel
Used Carrier Number 12
Railway Cell Resource 13
refGCellEquipmentFunctionNo#1
carrierNum#13 hsrCellOutInletFlag#13
4
End ID 13 of High-speed Used GSM Cell Channel
Used Carrier Number 13
Railway Cell Resource 14
refGCellEquipmentFunctionNo#1
carrierNum#14 hsrCellOutInletFlag#14
5
End ID 14 of High-speed Used GSM Cell Channel
Used Carrier Number 14
Railway Cell Resource 15
refGCellEquipmentFunctionNo#1
carrierNum#15 hsrCellOutInletFlag#15
6
End ID 15 of High-speed Used GSM Cell Channel
Used Carrier Number 15
Railway Cell Resource 16
refGCellEquipmentFunctionNo#1
carrierNum#16 hsrCellOutInletFlag#16
7
End ID 16 of High-speed Used GSM Cell Channel
Used Carrier Number 16
Railway Cell Resource 17
refGCellEquipmentFunctionNo#1
carrierNum#17 hsrCellOutInletFlag#17
8
End ID 17 of High-speed Used GSM Cell Channel
Used Carrier Number 17
Railway Cell Resource 18
refGCellEquipmentFunctionNo#1
carrierNum#18 hsrCellOutInletFlag#18
9
End ID 18 of High-speed Used GSM Cell Channel
Used Carrier Number 18
Railway Cell Resource 19
refGCellEquipmentFunctionNo#2
carrierNum#19 hsrCellOutInletFlag#19
0
End ID 19 of High-speed Used GSM Cell Channel
Used Carrier Number 19
Railway Cell Resource 20
refGCellEquipmentFunctionNo#2
carrierNum#20 hsrCellOutInletFlag#20
1
End ID 20 of High-speed Used GSM Cell Channel
Used Carrier Number 20
Railway Cell Resource 21
refGCellEquipmentFunctionNo#2
carrierNum#21 hsrCellOutInletFlag#21
2
End ID 21 of High-speed Used GSM Cell Channel
Used Carrier Number 21
Railway Cell Resource 22
refGCellEquipmentFunctionNo#2
carrierNum#22 hsrCellOutInletFlag#22
3
End ID 22 of High-speed Used GSM Cell Channel
Used Carrier Number 22
Railway Cell Resource 23
refGCellEquipmentFunctionNo#2
carrierNum#23 hsrCellOutInletFlag#23
4
End ID 23 of High-speed Used GSM Cell Channel
Used Carrier Number 23
Railway Cell Resource 24
refGCellEquipmentFunctionNo#2
carrierNum#24 hsrCellOutInletFlag#24
5
End ID 24 of High-speed Used GSM Cell Channel
Used Carrier Number 24
Railway Cell Resource 25
refGCellEquipmentFunctionNo#2
carrierNum#25 hsrCellOutInletFlag#25
6
End ID 25 of High-speed Used GSM Cell Channel
Used Carrier Number 25
Railway Cell Resource 26
refGCellEquipmentFunctionNo#2
carrierNum#26 hsrCellOutInletFlag#26
7
End ID 26 of High-speed Used GSM Cell Channel
Used Carrier Number 26
Railway Cell Resource 27
refGCellEquipmentFunctionNo#2
carrierNum#27 hsrCellOutInletFlag#27
8
End ID 27 of High-speed Used GSM Cell Channel
Used Carrier Number 27
Railway Cell Resource 28
refGCellEquipmentFunctionNo#2
carrierNum#28 hsrCellOutInletFlag#28
9
End ID 28 of High-speed Used GSM Cell Channel
Used Carrier Number 28
Railway Cell Resource 29
refGCellEquipmentFunctionNo#3
carrierNum#29 hsrCellOutInletFlag#29
0
End ID 29 of High-speed Used GSM Cell Channel
Used Carrier Number 29
Railway Cell Resource 30
refGCellEquipmentFunctionNo#3
carrierNum#30 hsrCellOutInletFlag#30
1
End ID 30 of High-speed Used GSM Cell Channel
Used Carrier Number 30
Railway Cell Resource 31
refGCellEquipmentFunctionNo#3
carrierNum#31 hsrCellOutInletFlag#31
2
End ID 31 of High-speed Used GSM Cell Channel
Used Carrier Number 31
Railway Cell Resource 32
refGCellEquipmentFunctionNo#3
carrierNum#32 hsrCellOutInletFlag#32
3
End ID 32 of High-speed Used GSM Cell Channel
Used Carrier Number 32
Railway Cell Resource 33
refGCellEquipmentFunctionNo#3
carrierNum#33 hsrCellOutInletFlag#33
4
End ID 33 of High-speed Used GSM Cell Channel
Used Carrier Number 33
Railway Cell Resource 34
refGCellEquipmentFunctionNo#3
carrierNum#34 hsrCellOutInletFlag#34
5
End ID 34 of High-speed Used GSM Cell Channel
Used Carrier Number 34
Railway Cell Resource 35
refGCellEquipmentFunctionNo#3
carrierNum#35 hsrCellOutInletFlag#35
6
End ID 35 of High-speed Used GSM Cell Channel
Used Carrier Number 35
Railway Cell Resource 36
End ID 36 of High-speed
Used Carrier Number 36 BCCH Preferred Channel No.
Railway Cell
It is applied in the
1:Y,scenario of high long:[0..216]
long:[1..6] speed railways configured with
0:N <default:0>
mutli-carrier combination group. It
BCCH preferred channel number.
is used to identify whether a
It represents the number of It is set in
channel is the inlet/outlet endpoint
carriers used for the cell on each refGCellEquipmentFunction. 0
of the mutli-carrier combination.
channel. It should correspond to indicates invalid, that is, the base
Each cell can be configured with
the configuration sequence of station does not specify BCCH
two endpoint channels at most.
refGCellEquipmentFunction. preferred channel and randomly
The configuration sequency of
allocates BCCH to a channel.
this prameters must correspond to
R-W-I R-W-I R-W-I
the configuration sequence of
refGCellEquipmentFunction. 0
0
bcchCarrierNo
long: [0..6]
<default:0>
BCCH preferred carrier number. 0
indicates invalid, that is, the base
station does not specify BCCH
preferred carrier and randomly
allocates BCCH to a carrier. If
gCellEquipmentFuncNo is set to
0, bcchCarrierNo must be 0.
R-W-I
0
0
{GCell_cellNo}
A,P long:[0..4095] long:[0..65535] long:[1..4294967295]
long:[1..54]
Generated
Configure as
automatically, it is
A:Add, P:Pass Same in an OMMB. Unique in subnetwork. GSM cell No.
unnecessary to fill in
"cellNo" of Gcell.
this column.
Return To Index Primary Key Primary Key Primary Key Primary Key
16 10 1 2
16 10 1 3
16 10 1 4
16 10 2 1
16 10 2 2
16 10 1 1
16 10 1 5
trxNo operatingMode multiCarrierGroupNo enableIRC mainBand
Multi-carrier
Logic Carrier Parent
Operating Mode Combination Group Use IRC or not
Frequency No. Frequency Band
No. 1: 2.1G(Band I),
2: 1900M(Band II),
3: 1800M(Band
0:Single carrier, 0:Disable IRC, III),
long:[1..60] 1:Dual-carrier, 1:Enable IRC, 5: 850M(Band V),
long:[0..32]
<default:1> 2:Multi-carrier 2:Enable STIRC 6: 850M(Band VI),
<default:0> <default:1> 8: 900M(Band
VIII),
9: 1800M(Band IX)
Multi-carrier <default:2>
Carrier frequency GSM carrier frequency
combination group used
ID. You can set it working mode In the
by carrier frequency. It It sets whether the
within the value case of four-antenna
is valid when feature "ZGO-04-01-
range. It is an receiving diversity, set
"operatingMode" is set 005 Uplink
interconnection this parameter to
to "Dual-carrier" or Interference Rejection
parameter. Different "Dual-carrier", and the
"Multi-carrier". 0 Combining (IRC)" is
cells can have the four antennas have the
indicates that it is enabled. This feature
same carrier same receiving range,
invalid. Its value comes can improve the uplink
frequency number, which enhances the
from the receiving signal quality
but the carrier uplink receiving
GCellEquipmentFunctio in the GSM system. It
frequency numbers capability. "Multi-
n affiliated multi-carrier is recommended to
of the same cell carrier" is applied in
combination group of enable this feature.
must differ from the case of multi-
the parent MO Gcell of
each other. carrier combination.
R-I R-W-I GTrx.
R-W-I R-W-I R-W-I
2 0 0 1 8
3 0 0 1 8
4 0 0 1 8
1 0 0 1 8
2 0 0 1 8
1 0 0 1 8
5 0 0 1 8
branchBand isExtendTrx mcumRxSelMode mcumTxSelMode
Extend Carrier Is Uplink Signal Selected Select RU Transmission
Sub Frequency Band
Frequency or not According to CIR or not
1: Y, 1: Y, 1: Y,
long:[1..3,255]
0: N 0: N 0: N
<default:255>
<default:0> <default:0> <default:0>