Professional Documents
Culture Documents
SECTION 21 - TRANSMISSIONS
CONTENTS
21-1
SECTION 21 – TRANSMISSIONS – CHAPTER 5
WARNING
Removal
Do not work under a raised tractor unless the
1. Park the tractor on a level surface, set the parking frame is securely supported with adequate
brake and install the articulation lock pin. stands and articulation lock pin installed. Do not
Remove the switch key. rely only on the jack or hoist to support the
2. Raise the tractor cab as detailed in Section 90 - tractor.
Cab.
21-2
SECTION 21 – TRANSMISSIONS – CHAPTER 5
NOTE: Cap and plug all hydraulic lines and ports
once they have been disconnected. 3
6. Remove the hydrostatic pump suction line (1) 2
from the tractor.
7. Remove the auxiliary charge pump suction line
(2).
8. Remove the implement pump case drain line (3)
as detailed in Section 35 – Hydraulics and
Steering of the repair manual.
9. Remove the suction tube (1) and supply tube (2) MT03G057 1
from the tractor.
10. Remove the four mounting bolts and remove the 1
filter assembly (3).
11. Remove and discard any ty-wraps that may
interfere with the removal of the hydraulic lines. 2
12. Remove the auxiliary pump case drain (4) from
the axle housing.
4
MT03H010
3
2
13. Remove the “A” port hose (1) and “B” port
tubeline (2) from the auxiliary pump. Remove the
“B” port tubeline from the return filter (3). 3
1
2
MA02M032
21-3
SECTION 21 – TRANSMISSIONS – CHAPTER 5
14. Tag and disconnect the charge inlet line (1) from
the auxiliary pump.
1
MA03H017
4
15. Disconnect the four prong electrical connector
(1) from the auxiliary pump.
1
19990223
5
16. Tag and disconnect the hydraulic line (1) from the
auxiliary pump.
17. Tag and disconnect the electrical fitting (2) from
the 90° fitting (3).
CAUTION 1
The auxiliary pump weighs approximately 36 Kg 2
(80 lbs.). Use caution when removing the pump
from the drive assembly.
21-4
SECTION 21 – TRANSMISSIONS – CHAPTER 5
Installation
1. If the following components were removed, on a
clean work bench assemble the following
components on the auxiliary pump.
Description Qty.
Adapter 1
Elbow 2
O ring 1
90° Elbow 1
Cap screw M12 x 40 2
2. Remove the plug from the auxiliary pump,
lubricate the O ring with petroleum jelly and 1
install the 90° elbow (1) Hand tighten the elbow
at this time.
19984563
7
3. Remove the plug from the auxiliary pump,
lubricate the O ring and install the adapter (1)
Tighten the adapter securely at this time.
19984564
21-5
SECTION 21 – TRANSMISSIONS – CHAPTER 5
4. Locate the ports of the auxiliary pump marked “A”
and “B” (1) and remove the plugs.
1
19984565
9
5. Lubricate the O rings for the two 90° elbows (1)
and install the elbows into the open ports of the
auxiliary pump. Hand tighten the elbows at this
time.
6. Lubricate the O ring (2) with petroleum jelly and
install the O ring to the mating surface around the 2
opening on the auxiliary pump.
NOTE: The auxiliary pump weighs approximately 36 1
Kg (80 lbs.). Use caution when installing onto the
pump drive assembly.
21-6
SECTION 21 – TRANSMISSIONS – CHAPTER 5
9. Connect the electrical fitting (2) to the 90°
fitting, 3.
10. Connect the hydraulic line (1) to the auxiliary
pump.
1
2
3
20006755
11
11. Connect the four prong electrical connector (1) to
the auxiliary pump.
1
19990223
12
12. Connect the charge inlet line (2) to the auxiliary
pump.
13. Connect the outlet line (1) to the auxiliary pump
case drain port.
2
19984588 1
13
21-7
SECTION 21 – TRANSMISSIONS – CHAPTER 5
14. Install the coupler hose on the “A” port (1) of the
pump.
15. Install the tubeline between the “B” port (2) and
the return.
3
1 2
MA02M030
14
16. Install and tighten the auxiliary pump case drain
line on the axle cover (1).
3
17. Install the auxiliary pump suction filter assembly
(1). Do not tighten the four mounting bolts.
5
18. Install the supply tube (2) on the axle cover. Do
not tighten the tube end nut (3).
19. Install and tighten the auxiliary pump suction filter
supply tube (5). Tighten the supply tube end nut
(4) and filter mounting bolts.
4 1
MT03H010 2
15
20. Install the implement pump case drain line (1) as
described in Section 35 – Hydraulics and 1
Steering of the repair manual.
21. Install the auxiliary pump suction line (2) between
the filter and the pump. 2
22. Install the hydrostatic pump suction line (3)
between the supply tube and the pump.
23. If applicable, install new ty–wraps in the locations
that the old ty–wraps were removed.
24. Install the right rear wheel and remove the cab 3
end support from the tractor. MT03G057
16
25. Connect the negative battery cables as detailed 28. Start the tractor and inspect the hydraulic lines
in Section 55 - Electrical. and fittings for any leakage. Repair the
26. Lower the tractor cab as detailed in Section 90 - connections as needed.
Cab. 29. To verify that the auxiliary hydraulic kit is
27. Fill the hydraulic fluid reservoir and using the operating properly, perform tests 13, 14, 15, and
sight glass, inspect the fluid level. Top off if 16 in Section 35 - Hydraulics and Steering.
necessary. 30. Remove the articulation lock pin. The tractor is
now ready to return to service.
21-8