Professional Documents
Culture Documents
WCS
A
B
SECTION
WARNING CHIME SYSTEM C
E
CONTENTS
PRECAUTION ............................................... 3 COMMON ITEM .........................................................18 F
COMMON ITEM : CONSULT Function (BCM -
PRECAUTIONS ................................................... 3 COMMON ITEM) .....................................................18
Precaution for Supplemental Restraint System G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- BUZZER .....................................................................18
SIONER" ................................................................... 3 BUZZER : CONSULT Function (BCM - BUZZER)....19
PARKING BRAKE RELEASE WARNING CHIME ...... 8 BCM (BODY CONTROL MODULE) ................. 29
PARKING BRAKE RELEASE WARNING CHIME List of ECU Reference .............................................29 M
: Parking Brake Release Warning Chime .................. 8
WIRING DIAGRAM ...................................... 30
SEAT BELT REMINDER WARNING CHIME .............. 9
SEAT BELT REMINDER WARNING CHIME : WARNING CHIME SYSTEM ............................. 30 WCS
Seat belt Warning ...................................................... 9 Wiring Diagram ........................................................30
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along C
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING: D
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer. E
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
F
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
G
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni- H
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the I
battery and wait at least three minutes before performing any service.
WCS
ALNIA1645ZZ
A
The combination meter has a built-in buzzer (1) and sounds the fol-
lowing warnings, according to signals from each switch and unit:
B
• Light reminder warning
• Parking brake release warning chime
• Seat belt warning
• Key warning chime C
D
JSNIA5954ZZ
WCS
AWNIA2651GB
AWNIA3129GB
Output signal
Output signal B
DESCRIPTION
Combination Meter D
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.
E
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
F
WARNING CHIME FUNCTION LIST
Function Specifications K
Buzzer The buzzer turns OFF by suspending communication.
WCS
AWNIA2539GB P
WARNING CHIME OPERATION CONDITIONS
If all of the following conditions are fulfilled:
Operation conditions
Ignition switch OFF
Combination switch (Lighting switch) 1st or 2nd position
Driver side door Open [front door switch LH ON]
Operation conditions
Ignition switch ON
Combination switch (Lighting switch) OFF or AUTO position
Driver side door Close [front door switch LH OFF]
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below.
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
SYSTEM DIAGRAM
JSNIA2422GB
Operation conditions
Ignition switch ON
Operation conditions C
Ignition switch OFF
Parking brake Release condition (parking brake switch OFF).
D
Vehicle speed Approximately 1.9 MPH (3 km/h) or less.
SIGNAL PATH
E
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter
H
SEAT BELT REMINDER WARNING CHIME
SEAT BELT REMINDER WARNING CHIME : Seat belt Warning INFOID:0000000011276458
I
SYSTEM DIAGRAM
J
AWNIA2652GB
SIGNAL PATH
Seat belt buckle switch signal LH Seat belt buckle switch LH Combination meter BCM
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
SYSTEM DIAGRAM
AWNIA3130GB
Operation conditions
Ignition switch OFF
Key switch ON (key is in key cylinder)
Driver side door Open [front door switch LH ON]
Operation conditions
Ignition switch ON
Key switch ON (key is removed from key cylinder)
Driver side door Close [front door switch LH OFF]
SIGNAL PATH
1. BCM detects key inserted into the ignition switch, and sends key warning signal to combination meter with
CAN communication line.
2. Combination meter sounds integrated buzzer, when it receives a buzzer output signal from BCM.
C
Signal name Signal source
WCS
JSNIA5944ZZ
H
Blue Red Pink
Green Light blue Yellow
I
White White Black
Light blue Black Pink
Black Blue Black J
Dark blue White Blue
K
*2: Error Code
WCS
JSNIA5945ZZ
O
Item Code Description Action to take/Reference
0 Normal —
A vehicle speed signal cannot be received P
1 from ABS actuator and electric unit (control
Speedometer unit). Perform “Self Diagnostic Result” of
“ABS.”
A vehicle speed signal received from the Refer to BRC-53, "DTC Index".
2 ABS actuator and electric unit (control unit)
is abnormal.
0 Normal —
Engine coolant temper- Perform “Self Diagnostic Result” of
ature gauge An engine coolant temperature signal can-
1 “ECM.”
not be received from ECM.
Refer to MWI-31, "DTC Index".
0 Normal —
When judging that the illumination control
1 switch signal circuit is shorted for 5 minutes
or more.
Meter control switch Refer to MWI-69, "Diagnosis Proce-
When judging that the trip reset switch sig-
2 dure".
nal circuit is shorted for 5 minutes or more.
When judging that the both switch signal cir-
3
cuit is shored for 5 minutes or more.
— 0 Displays “0” constantly. —
APPLICATION ITEMS
CONSULT can display each diagnostic item using the diagnostic test modes shown.
MAIN A
Display item [Unit] Description
SIGNALS
SPEED METER
X Displays the value of vehicle speed signal.
B
SPEED OUTPUT
X Vehicle speed signal value transmitted to other units via CAN communication.
[mph or km/h]
ODO OUTPUT C
Odometer signal value transmitted to other units via CAN communication.
[mph or km/h]
TACHO METER
X Value of the engine speed signal received from ECM via CAN communication.
[rpm] D
FUEL METER
X Fuel level indicated on combination meter.
[L]
W TEMP METER
X Displays the value of engine coolant temperature signal, which is input from ECM.
E
[°F] or [°C]
ABS W/L
Displays [ON/OFF] condition of ABS warning indicator.
[On/Off]
F
VDC/TCS IND
Displays [ON/OFF] condition of VDC OFF indicator lamp.
[On/Off]
SLIP IND G
Displays [ON/OFF] condition of SLIP indicator lamp.
[On/Off]
BRAKE W/L
Displays [ON/OFF] condition of brake warning indicator.
[On/Off]
H
DOOR W/L Displays [ON/OFF] condition of door or liftgate warning message in the informa-
[On/Off] tion display.
HI-BEAM IND I
Displays [ON/OFF] condition of high beam indicator.
[On/Off]
TURN IND
Displays [ON/OFF] condition of turn indicator.
[On/Off]
J
LIGHT IND
Displays [ON/OFF] condition of light indicator.
[On/Off]
FR FOG IND
Displays [ON/OFF] condition of front fog lamp indicator. K
[On/Off]
OIL W/L Displays [ON/OFF] condition of low oil pressure warning message in the informa-
[On/Off] tion display.
L
O/D OFF IND
Displays [ON/OFF] condition of O/D OFF indicator.
[On/Off]
DDS W/L
Displays [ON/OFF] condition of hill descent control warning indicator. M
[On/Off]
MIL
Displays [ON/OFF] condition of malfunction indicator.
[On/Off]
WCS
SPORT IND
Displays [ON/OFF] condition of SPORT indicator.
[On/Off]
CHAGE W/L
Displays [ON/OFF] condition of charge warning indicator. O
[On/Off]
4WD LOCK IND
Displays [ON/OFF] condition of AWD LOCK indicator lamp.
[On/Off]
4WD W/L P
Displays [ON/OFF] condition of AWD warning message in the information display.
[On/Off]
FUEL W/L
Displays [ON/OFF] condition of low-fuel warning message.
[On/Off]
WASHER W/L
Displays [ON/OFF] condition of low washer fluid warning message.
[On/Off]
WORK SUPPORT
WARNING HISTORY
Special menu
W/L ON HISTORY
B
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds. C
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: No warning/indicator lamp history is stored.
NOTE: D
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
E
WCS
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEADLAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Intelligent Key system INTELLIGENT KEY × × × ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
Signal buffer system SIGNAL BUFFER ×
Air conditioner AIR CONDITIONER ×
BUZZER
A
DATA MONITOR
ACTIVE TEST E
WCS
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions.
Configuration
Work support
Data Monitor
Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT ×
Exterior lamp HEADLAMP × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × ×
Combination switch COMB SW ×
BCM BCM × × × × ×
Immobilizer IMMU × ×
Interior room lamp battery saver BATTERY SAVER × ×
Back door open TRUNK ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR ×
TPMS AIR PRESSURE MONITOR × × × ×
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER) INFOID:0000000011403298
DATA MONITOR
Revision: August 2014 WCS-20 2015 Rogue NAM
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
ACTIVE TEST
C
Test Item Description
SEAT BELT WARN TEST This test is able to check seat belt warning chime operation [On/Off].
LIGHT WARN ALM This test is able to check light warning chime operation [On/Off]. D
REVERSE WARNING This test is able to check reverse warning chime operation [On/Off].
ID REGIST WARNING This test is able to check TPMS sensor ID regist warning chime operation [On/Off].
E
WCS
JSNIA6097ZZ
PHYSICAL VALUES
Terminal No.
Description
(Wire color)
Value
Input/ Condition
(Approx.)
+ – Signal name Out-
put
1
Ground Ground — — — 0V
(B)
Ignition Security indicator ON. 0V
7
Ground Security signal Input switch
(BG) Security indicator OFF. Battery voltage
OFF
9
Ground ECO mode switch — — — —
(GR)
10
Ground O/D OFF switch — — — —
(P)
Ignition C
15
Ground Ambient sensor signal Input switch —
(L)
ON
D
JSNIA0014GB
JSNIA0012GB
NOTE:
The maximum voltage varies de-
pending on the specification (desti-
nation unit).
Ignition Speedometer operated
39 Vehicle speed signal Out-
Ground switch [When vehicle speed is approx.
(W) (2-pulse) put
ON 25 MPH (40 km/h)].
JSNIA0015GB
41
Ground CAN high — — — —
(L)
42
Ground CAN low — — — —
(P)
JSNIA5983GB
Ignition
43 Illumination control sig- Out-
Ground switch
(W) nal put
ON
• Lighting switch 1st position
• When meter illumination is step
11.
JPNIA1686GB
Fail-safe INFOID:0000000011386494
The combination meter activates the fail-safe control if the CAN communication lines between each unit are G
malfunctioning.
Function Specifications H
Speedometer
Tachometer Reset to zero by suspending communication.
I
Engine coolant temperature gauge
Meter illumination control When suspending communication, changes to nighttime mode.
Buzzer Turns OFF by suspending communication. J
Current fuel consumption
Average fuel consumption
Average vehicle speed The last result calculated during normal condition is indicated. K
Range (Distance to empty)
Driving distance L
Door open warning
Lift gate open warning
Information display Low tire pressure warning M
Parking brake release warning
The display turns OFF by suspending communication.
Fuel filler cap warning
WCS
Oil pressure warning
CVT warning
BSW/LDW warning O
Odo/trip meter An indicated value is maintained at communications blackout.
Shift position indicator The indicator turns OFF by suspending communication.
P
B
ECU Reference
BCS-28, "Reference Value"
BCS-46, "Fail Safe" C
BCM (with Intelligent Key system)
BCS-46, "DTC Inspection Priority Chart"
BCS-47, "DTC Index"
D
BCS-96, "Reference Value"
BCS-107, "Fail Safe"
BCM (without Intelligent Key system)
BCS-107, "DTC Inspection Priority Chart" E
BCS-108, "DTC Index"
WCS
AANWA1193GB
WCS
AANWA1194GB
AANIA3206GB
WCS
AANIA3207GB
AANIA3245GB
WCS
AANIA3284GB
AANIA3285GB
OVERALL SEQUENCE
C
JSNIA4485GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS
1. Connect CONSULT and perform "self-diagnosis". Refer to WCS-28, "DTC Index".
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> Inspection End.
NO >> GO TO 1.
C
Regarding Wiring Diagram information, refer to MWI-33, "Wiring Diagram".
D
1.CHECK FUSES
Check that the following fuses are not blown.
E
Unit Power source Fuse No.
Battery 13
Combination meter
Ignition switch ON or START 31 F
Is the fuse blown?
YES >> Replace the blown fuse after repairing the affected circuit.
G
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Disconnect combination meter connector. H
2. Check voltage between combination meter harness connector M77 terminals 45, 46 and ground.
M
Combination meter
Ground Continuity
Connector Terminal
M76 1 WCS
(–) Yes
M77 52
Is the inspection result normal?
YES >> Inspection End. O
NO >> Repair or replace harness or connector.
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM)
P
BCM (BODY CONTROL SYSTEM) (WITH INTELLIGENT KEY SYSTEM) : Diagnosis
Procedure INFOID:0000000011386497
BCM Voltage
Ground
Connector Terminal (Approx.)
BCM
Ground Continuity
Connector Terminal
170
M20 — Yes
171
Is the inspection result normal?
YES >> Inspection End.
NO >> Repair or replace harness or connectors.
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM)
BCM (BODY CONTROL SYSTEM) (WITHOUT INTELLIGENT KEY SYSTEM) : Diag-
nosis Procedure INFOID:0000000011386498
1. CHECK FUSE
Check that the following fuse is not blown.
BCM Voltage
A
Ground
Connector Terminal (Approx.)
WCS
• The buzzer for the warning chime system is installed in the combination meter.
• The combination meter sounds the buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000011276476
J
Combination meter
Voltage
Terminals Condition
Connector (Approx.)
(+) (-) K
When seat belt LH is fastened Battery voltage
M76 28 Ground
When seat belt LH is unfastened 0V
L
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-84, "Removal and Installation".
NO >> GO TO 2.
M
2. CHECK SEAT BELT BUCKLE SWITCH LH CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter harness connector M76 and seat belt buckle switch LH harness connector WCS
B87.
3. Check continuity between combination meter harness connector M76 terminal 28 and seat belt buckle
switch LH harness connector B87 terminal 1.
O
Combination meter
Continuity
Connector Terminal Ground
M76 28 No
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness or connector.
3. CHECK SEAT BELT BUCKLE SWITCH LH GROUND CIRCUIT
Check continuity between seat belt buckle switch LH harness connector B87 terminal 2 and ground.
1.CONNECTOR INSPECTION F
1. Turn ignition switch OFF.
2. Disconnect combination meter and parking brake switch connectors.
3. Check connectors and terminals for deformation, disconnection, looseness or damage.
G
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace as necessary. H
2.CHECK PARKING BRAKE SWITCH
Check parking brake switch. Refer to WCS-46, "Component Inspection".
Is the inspection result normal? I
YES >> GO TO 3.
NO >> Replace parking brake switch. Refer to PB-7, "Exploded View".
3.CHECK PARKING BRAKE SWITCH SIGNAL J
With CONSULT.
1. Connect combination meter connector and parking brake switch connectors. K
2. Turn ignition switch ON.
3. Select “METER/M&A”.
4. Monitor “PKB SW” in “Data Monitor” while applying and releasing the parking brake.
L
Combination meter
— Continuity
Connector Terminal
M76 26 Ground No
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-84, "Removal and Installation".
NO >> Repair or replace malfunctioning components.
Component Inspection INFOID:0000000011276484
D
Monitor Item Condition Status
When key is removed from key cylinder OFF
KEY ON SW
When key is inserted into key cylinder ON E
Is the inspection result normal?
YES >> Inspection End.
NO >> Refer to WCS-47, "Diagnosis Procedure". F
G
Regarding Wiring Diagram information, refer to WCS-30, "Wiring Diagram".
H
1. CHECK BCM INPUT SIGNAL
Check voltage between BCM harness connector M19 terminal 81 and ground.
I
Terminals
(+)
Condition
Voltage J
(−) (Approx.)
BCM
Terminal
connector
Key is inserted Battery voltage K
M19 81 Ground
Key is removed 0V
Is the inspection result normal?
L
YES >> Inspection End.
NO >> GO TO 2.
2. CHECK KEY SWITCH CIRCUIT M
1. Disconnect BCM connector M19 and key switch.
2. Check continuity between BCM harness connector M19 terminal 81 and key switch harness connector
M105 terminal 1. WCS
BCM
Continuity
Connector Terminal Ground
M19 81 No
Is the inspection result normal?
YES >> GO TO 3.
Terminals
Voltage
(+)
(–) (Approx.)
Key switch Terminal
M105 1 Ground Battery voltage
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace harness or connector.
4. CHECK KEY SWITCH GROUND CIRCUIT
Check continuity between key switch harness connector M105 terminal 2 and ground.
Key switch
Continuity
Connector Terminal Ground
M105 2 Yes
Is the inspection result normal?
YES >> Replace key switch. Refer to SEC-195, "Removal and Installation".
NO >> Repair or replace harness or connector.
Component Inspection INFOID:0000000011276488
WCS
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
Diagnosis Procedure INFOID:0000000011276491
WCS
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure INFOID:0000000011276495
The key warning chime does not sound, when all of the following conditions are fulfilled: B
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in OFF position (ignition switch signal OFF).
• Driver side door is open (front door switch LH ON)
C
Diagnosis Procedure INFOID:0000000011276497
WCS