Professional Documents
Culture Documents
PROJECT/TRAINING REPORT
(Times New Roman, 16 pt. Bold)
Name: ______________________
SUBMITTED TO: Er. Ashwani Katoch
University Roll No.____________
(Times New Roman, 14 pt. Bold)
1. Cover Page
2. Inner Pages
a) Certificate by Company/Industry/Institute
b) Declaration by student
c) Acknowledgement
d) About Company/Industry/Institute(with logo of company)
3. Table of Contents
4. List of Tables
5. List of Figures
6. Abbreviations and Nomenclature (If any)
7. Chapter-1
Introduction to Project ( All topic are mentioned with 1.1,
1.2, 1.3………. numbering )
(Figures also mentioned with numbering eg- fig 1.1,1.2,1.3..-
title of figure)
8. Chapter-2
Tools & Technology Used Project ( All topic are mentioned
with 2.1, 2.2, 2.3………. numbering )
(Figures also mentioned with numbering eg- fig
2.1,2.2,2.3……- title of figure)
9.Chapter -3
Snapshots(colored snapshot) ( All topic are mentioned with
3.1, 3.2, 3.3………. numbering )
(Figures also mentioned with numbering eg- fig
3.1,3.2,3.3……- title of figure)
10. Chapter-4
Results and Discussions( All topic are mentioned with 4.1,
4.2, 4.3………. numbering )
(Figures also mentioned with numbering eg- fig
4.1,4.2,4.3……- title of figure)
11. Chapter-5
12. References
4. The training report shall be computer typed (English- British, Font -Times
Roman, Size-12 point) and printed on A4 size paper.
5. The training report shall be hard bound with cover page in BLUE(SKY BLUE)
color. The name of the students, degree, duration of training period, name
of the university including institute name shall be printed in Golden letters
on the cover page.
6. The training report shall be typed with 1.5 line spacing with a margin 3.5 cm
on the left, 2.5 cm on the top, and 1.25 cm on the right and at bottom. Every
page in the report must be numbered. The page numbering, starting from
acknowledgements and till the beginning of the introductory chapter, should
be printed in small Roman numbers, i.e, i, ii, iii, iv...... The page number of
the first page of each chapter should not be printed (but must be accounted
for). All page numbers from the second page of each chapter should be
printed using Arabic numerals, i.e. 2,3,4,5... All printed page numbers
should be located at the bottom centre of the page.
7. The table of contents should list all headings and sub-headings. The title
page and certificates will not find a place among the items listed in the
Table of Contents. One and a half line spacing should be adopted for typing
the matter under this head.
8. The list of tables should use exactly the same captions as they appear
above the tables in the text. One and a half spacing should be adopted for
typing the matter under this head.(example shown below)
9. The list of figures should use exactly the same captions as they appear
below the figures in the text. One and a half spacing should be adopted for
typing the matter under this head.
10.The list of symbols, abbreviation & nomenclature should be typed with one
and a half line spacing. Standard symbols, abbreviation etc should be used.
(Signature of student)
(Name of Student)
(University Roll No.)
Date: ____________________
Certified that the above statement made by the student is correct to the best of our knowledge
and belief.
Signatures
Examined by:
1. 2. 3.
Head of Department
(Signature and Seal)
CERTIFICATE
(16 Times New Roman, bold)
This is to certify that Mr. / Ms.___________________________ has partially completed /
completed / not completed the 6-Month Industrial Training during the period from _______
to_______ in our Organization / Industry as a Partial Fulfillment of Degree of Bachelor of
Technology in Computer Science Engineering. He / She was trained in the field of
______________________________ .
CHAPTER 1...............................................................................................................PAGE NO
INTRODUCTION TO THE PROJECT
1.1 HEADING…………………………PAGE NO
1.2………………………………………PAGE NO
1.3………………………………………PAGE NO
1.4………………………………………PAGE NO
1.5………………………………………PAGE NO
CHAPTER 2...............................................................................................................PAGE NO
CHAPTER TITEL
2.1…………… ...........................PAGE NO
2.2……………………………………………………………… PAGE NO
CHAPTER 3...............................................................................................................PAGE NO
CHAPTER TITEL
3.1………………………….............................. PAGE NO
3.2……………………………………………………….PAGE NO
CHAPTER 4...............................................................................................................PAGE NO
CHAPTER TITEL
4.1…………….………………………....PAGE NO.
4.2…………………….…………………………………..PAGE NO.
4.3………………………………………………….……PAGE NO
CHAPTER 5...............................................................................................................PAGE NO
CHAPTER TITEL
5.1……………………………………………….………….PAGE NO
5.2…………………………..…………PAGENO
BIBLIOGRAPHY...............................................................................................PAGE NO
CHAPTER-NO
( Technology logo)
1.1-1rst heading
1.2- 2nd heading
1.3-3rd heading
………………………
………………………
TITEL OF CHAPTER
(eg---- name of the project )
Note:-please insert this chapter title page before every chapter. Change chapter
number, chapter title and heading number according to chapter wise .Deigned
chapter title page with boarder