Professional Documents
Culture Documents
IPN = 6, 10, 25 A
For the electronic measurement of current: DC, AC, pulsed..., with galvanic separation
between the primary and the secondary circuit.
Features Applications
●● Hall effect measuring principle ●● AC variable speed drives
●● Galvanic separation between primary and secondary circuit ●● Static converters for DC motor drives
●● Insulated test voltage 4300 V ●● Battery supplied applications
●● Low power consumption ●● Uninterruptible Power Supplies (UPS)
●● Single power supply +5 V ●● Switched Mode Power Supplies (SMPS)
●● Fixed offset & sensitivity ●● Power supplies for welding applications
●● Over-current detect 2.63 × IPN (peak value) ●● The solar inverter on DC side of the inverter (MPPT)
●● Memory check. ●● Combiner box.
Advantages Standards
●● Small size and space saving ●● EN 50178: 1997
●● Only one design for wide primary current range ●● IEC 61010-1: 2010
●● High immunity to external interference ●● IEC 61326-1: 2012
●● 8 mm creepage /clearance ●● UL 508: 2010.
●● High insulation capability
Application Domain
●● Fast response.
●● Industrial.
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Stresses above these ratings may cause permanent damage. Exposure to absolute maximum ratings for extended periods may
degrade reliability.
Standards
●● CSA C22.2 NO. 14-10 INDUSTRIAL CONTROL EQUIPMENT - Edition 11 - Revision Date 2011/08/01
●● UL 508 STANDARD FOR INDUSTRIAL CONTROL EQUIPMENT - Edition 17 - Revision Date 2010/04/15
Ratings
Conditions of acceptability
When installed in the end-use equipment, consideration shall be given to the following:
1 - These devices have been evaluated for overvoltage category III and for use in pollution degree 2 environment.
2 - A suitable enclosure shall be provided in the end-use application.
3 - The terminals have not been evaluated for field wiring.
4 - These devices have been evaluated for use in 105°C maximum surrounding air temperature.
5-T he secondary (Sensing) circuit is intended to be supplied by a Isolated Secondary Circuit - Limited voltage circuit defined
by UL 508 paragraph 32.5. The maximum open circuit voltage potential available to the circuit and overcurrent protection
shall be evaluated in the end use application.
6-T hese devices are intended to be mounted on a printed wiring board of end-use equipment. The suitability of the
connections (including spacings) shall be determined in the end-use application.
7 - Any surface of polymeric housing have not been evaluated as insulating barrier.
8-L ow voltage circuits are intended to be powered by a circuit derived from an isolating source (such as a transformer, optical
isolator, limiting impedance or electro-mechanical relay) and having no direct connection back to the primary circuit (other
than through the grounding means).
Marking
Only those products bearing the UL or UR Mark should be considered to be Listed or Recognized and covered under UL's
Follow-Up Service. Always look for the Mark on the product.
Page 2/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Insulation coordination
Note: 1) Voltage of Retention pins has to be consider. If it is same as primary electrical potential, insulation is no issue.
If it is same as secondary electrical potental, insulation of primary bus bar has to be considered.
Page 3/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Current consumption IC mA 19 25
-20 °C .. 85 °C
±160
Internal reference
Temperature coefficient of VREF TCVref ppm/K
-40 °C .. 105 °C
±190
Internal reference
-20 °C .. 85 °C
Temperature coefficient of VOE TCVOE mV/K ±0.14
-40 °C .. 105 °C
Gain error with respect to UC ±10 % %/% ±0.05 Gain error per UC drift
Note: 1)
Accuracy @ IP and XTA = ± [X + (TCG/10000) · (TA - 25) + TCVOE · 100 · (TA -25) / (Gth · IP)].
Page 4/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Current consumption IC mA 19 25
-20 °C .. 85 °C
±160
Internal reference
Temperature coefficient of Vref TCVref ppm/K
-40 °C .. 105 °C
±190
Internal reference
Gain error with respect to UC ±10 % %/% ±0.05 Gain error per UC drift
Over-current detect V 2.6 × IPN 2.9 × IPN 3.2 × IPN peak value
Note: 1)
Accuracy @ IP and XTA = ± [X + (TCG/10000) · (TA - 25) + TCVOE · 100 · (TA -25) / (Gth · IP)].
Page 5/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Current consumption IC mA 19 25
-20 °C .. 85 °C
±160
Internal reference
Temperature coefficient of Vref TCVref ppm/K
-40 °C .. 105 °C
±190
Internal reference
Gain error with respect to UC ±10 % %/% ±0.05 Gain error per UC drift
Over-current detect V 2.6 × IPN 2.9 × IPN 3.2 × IPN peak value
Note: 1)
Accuracy @ IP and X TA = ± [X + (TCG/10000) · (TA - 25) + TCVOE · 100 · (TA -25) / (Gth · IP)].
Page 6/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Unless otherwise stated (e.g. “100 % tested”), the LEM definition for such intervals designated with “min” and “max” is that
the probability for values of samples to lie in this interval is 99.73 %. For a normal (Gaussian) distribution, this corresponds
to an interval between -3 sigma and +3 sigma. If “typical” values are not obviously mean or average values, those values are
defined to delimit intervals with a probability of 68.27 %, corresponding to an interval between -sigma and +sigma for a normal
distribution.
Typical, maximal and minimal values are determined during the initial characterization of a product.
Page 7/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
50 62.5
40 50
30 37.5
IP (A)
IP (A)
20 25
10 12.5
HO
15A 6
HO
15A 10
0 0
0 25 50 75 100 125 0 25 50 75 100 125
TA(℃) TA(℃)
100
75
IP (A)
50
25
HO 25
0
0 25 50 75 100 125
TA(℃)
Important notice: whatever the usage and/or application, the primary conductor temperature shall not go above the maximum
rating of 125 °C as stated in page 2 of this datasheet.
Page 8/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
50
Upper limit: IP = -10 × Vref +45 (Vref = 0.5 .. 2.65 V)
40
30 Lower limit: IP = -10 × Vref +5 (Vref = 0.5 .. 2.65 V)
20
IP (A)
10
0
-10
-20 HO 6
-30
0.5 1 1.5 2 2.5
Vref (V)
10
0
-10
-20
-30 HO 10
-40
0.5 1 1.5 2 2.5
Vref (V)
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
PCB Footprint
Assembly on PCB
• Recommended PCB hole diameter 1.5 mm for retention pin
0.9 mm for secondary pin
• Maximum PCB thickness 2.4 mm
• Wave soldering profile maximum 260 °C, 10 s
No clean process only
Safety
This transducer must be used in limited-energy secondary circuits according to IEC 61010-1.
This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in
accordance with the manufacturer’s operating instructions.
Page 10/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
offset is:
TCVOE : temperature coefficient of VOE (mV/K)
Note: the transducer has to be demagnetized prior to
G : sensitivity of the transducer (V/At)
the application of the current cycle (for example with a
TCG : temperature coefficient of G (%/K)
demagnetization tunnel).
εG : sensitivity error (%)
εL : linearity error for ΘP (%) Overall accuracy
This model is valid for primary ampere-turns ΘP between -ΘP max The overall accuracy at 25 °C XG is the error in the - IPN .. + IPN
and +ΘP max only. range, relative to the rated value IPN.
It includes:
Sensitivity and linearity ●● the electrical offset VOE
To measure sensitivity and linearity, the primary current (DC) is ●● the sensitivity error εG
cycled from 0 to IP, then to -IP and back to 0 (equally spaced
●● the linearity error εL (to IPN) (%)
IP/10 steps). The sensitivity G is defined as the slope of the linear
regression line for a cycle between ± IPN. Response and reaction times
The linearity error εL is the maximum positive or negative
difference between the measured points and the linear regression The response time tr and the reaction time tra are shown in
line, expressed in % of IPN. figure 18.
Both depend on the primary current di/dt. They are measured
Magnetic offset at nominal ampere-turns.
The magnetic offset voltage VOM is the consequence of a current I
on the primary side (“memory effect” of the transducer’s ferro-
magnetic parts). It is measured using the following primary 100 %
current cycle. VOM depends on the current value IP1 (IP1> IPM). 90 %
Vout
V (t ) − V (t ) Ip
V = out 1 out 2
2
OM
tr
10 %
tra t
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com
HO-P series
Dimensions HO 6-P, HO 10-P, HO 25-P (mm, general linear tolerance ±0.5 mm)
Operation principle
OUT
1
+Uc
2 47nF
0V
5Ω 3 4.7nF
Vout
200Ω 4 47nF
Vref (IN/OUT)
5 >10kΩ
OCD
Ip
IN
+Uc
0V
Vout dCI dCp
Vref (IN/OUT)
OCD
Remarks
·There are 6 retention pins which have to be used only for retention as well as into the section called "Assembly on PCB".
·The pimary conductor to be measured should go through the aperture 8 × 8 mm.
Page 12/12
21October2014/Version 3 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice www.lem.com