Professional Documents
Culture Documents
SEMESTER - III
Exam Scheme
Sr.
Subject Code Scheme Theory Tuto. Pract. Total Credit
No.
Hrs. Marks Marks Marks
Engineering
2. ME201 4–1–0 3 100 25 - 125 05
Thermodynamics
Measurement and
5. ME207 3–1–2 3 100 25 50 175 05
Instrumentation
Page 1 of 22
Engineering Mathematics-III L T P Credit
MA213 3 1 0 04
2. Syllabus
INFINITE SERIES (06 Hours)
Introduction, positive term series, comparison test, Cauchy’s root test, D’Alembert’s test, Raabe’s
test, Logarithmic test, Integral test, Gauss’s test, Series with arbitrary terms, Rearrangement of terms.
Page 2 of 22
3. Books Recommended:
1. E. Kreyszig, Advanced Engineering Mathematics, 10th Edition, John Wiley, 2011.
2. C. R. Wylie, Advanced Engineering Mathematics, 6th Edition, McGraw Hill Education,
1995.
3. P. V. O’Neil, Advanced Engineering Mathematics, 7th Edition, Cengage, 2012.
4. M. D. Greenberg, Advanced Engineering Mathematics, 2nd Edition, Pearson Education,
2002.
5. B. V. Ramana, Higher Engineering Mathematics, 1st Edition, McGraw-Hill, New Delhi,
2010.
Further Reading:
1. S.S. Chapra and R.P. Canale, Numerical Methods for Engineers, 7th Edition, McGraw Hill
International Edition, 2015.
2. K.S. Rao, Numerical Methods for Scientists and Engineers, 3rd Edition, Prentice-Hall India,
2007.
Page 3 of 22
Engineering Thermodynamics L T P Credit
4 1 0 05
ME201
2. Syllabus
INTRODUCTION (02 Hours)
Page 4 of 22
STEAM GENERATIORS (08 Hours)
Types of steam generators like natural circulation and forced circulation. Heat recovery steam
generators (HRSG) with LP and HP evaporators, economizers, super heaters and air preheaters. High
pressure boilers such as La Mont, Loeffler, Benson, Schmidt, Velox Boiler. Performance of boilers.
3. Books Recommended:
1. W. Van, R.E. Sonnetag and C. Borgnakke, Fundamental of Classical Thermodynamics,
John Wiley & sons, 2005.
2. P K Nag, Engineering Thermodynamics, McGraw Hill Education Private Limited, 2013.
3. Y.A. Cengel and M.A. Boles, Thermodynamics, Tata McGraw Hill, 2004.
4. C.P. Kothandaraman, P.R. Khajuria and S. Domkundrar, A Course in Thermal Engineering,
Dhanpat Rai & Sons,2004.
5. P.L. Ballaney, Thermal Engineering, Khanna Publishers, 2000.
Page 5 of 22
Theory of Machines L T P Credit
3 1 2 05
ME203
2. Syllabus
Page 6 of 22
to helical, Spiral, Worm, Worm gear and bevel gears. Types of Gear trains. Kinematic analysis of
gear trains, Differential of an Automobile.
3. Practicals:
4. Books Recommended:
Page 7 of 22
Metallurgy L T P Credit
ME205 3 0 2 04
___________________________________________________________________________
1. Course Outcomes (COs):
CO1 Describe the importance of metallurgical industries and explain the basic principles of
metallography and extraction of metallic elements.
CO2 Explain the microstructure of ferrous and non-ferrous alloys and correlate the same with
their properties and applications.
CO3 Analyze solidification mechanisms of metals and apply the same for control of structure of
engineering products
CO4 Describe strengthening mechanisms of metallic materials, and explain the elastic/plastic
deformation of metallic materials.
CO5 Explain the phase-equilibria in binary alloys and analyze phase diagrams for binary alloys.
CO6 Explain the principle, procedure and application of heat-treatments of ferrous and non-
ferrous alloys.
CO7 Explain the principles, procedures, advantages and limitations of non-destructive testing
techniques.
2. Syllabus:
3. Practicals:
4. Books Recommended:
1. R. Balasubramanian, Callister’s Materials Science and Engineering, John Wiley & Sons, 2014.
2. D. R. Askland, P. P. Fulay, W. J. Wright, The Science and Engineering of Materials, Cengage
Learning, 2015.
3. S. H. Avner, Introduction to Physical Metallurgy, McGraw-Hill, 2017.
4. O. P. Khanna, A Text book of Materials Science And Metallurgy, Dhanpat Rai Publications.
5. W. Smith, J. Hashemi, R. Prakash, Materials Science & Engineering, McGraw Hill, 2014.
Page 9 of 22
Measurements And Instrumentation
L T P Credit
ME207 3 1 2 04
2. Syllabus
3. Practicals:
4. Books Recommended:
1. O. E. Doeblin and D. N. Manik, Measurements System, 7th Edition, McGraw Hill, 2019
2. Richard S. Figiliola,Theory and Design for Mechanical Measurements; 6thEdition, Wiley
India, 2015
3. D. S. Kumar, Mechanical Measurement and control,5th edition, Metropolitan Book Co. (P) Ltd.,
(2015)
4. A. K. Sawhney and Puneet Sawhney, A Course in Mechanical Measurements and Instrumentation
and Control, Dhanpat Rai & Co., 2017
5. R. K. Rajput, Mechanical Measurements and Instrumentation, Kataria and sons, 2013
Page 11 of 22
Teaching Scheme: B. Tech. (Mechanical Engineering) II Year
SEMESTER - IV
Exam Scheme
Sr.
Subject Code Scheme Theory Tuto. Pract. Total Credit
No.
Hrs. Marks Marks Marks
Machine Design
3. ME206 4–0–4 3 100 - 100 200 06
and Drawing
Dynamics of
4. ME208 3–1–2 3 100 25 50 175 05
Machines
Industrial
5. ME212 3–0–0 3 100 - - 100 03
Engineering
Page 12 of 22
Fluid Mechanics L T P Credit
ME202 3 1 2 05
2. Syllabus
FLUID KINEMATICS (12 Hours)
Velocity Field, Steady and unsteady Flows, One, Two and Three Dimensional Flows, Uniform and
non-uniform flows, Steam Lines and Stream Tubes, Path Lines and Streak Lines, Euler and
Lagrangian Methods, Substantial Derivative and Acceleration, Translation, Rotation and
Deformations, Vorticity , Rotational and Irrotational flows, Circulation, Velocity Potential function,
Equation of Continuity in differential form for Cartesian and cylindrical coordinate system, Equation
of Stream Line, Discharge in Terms of Steam Function, Stream Function and Velocity Potential
function, Laplace Equation in terms of Stream Function and Velocity Potential function, Boundary
Conditions, Flow Nets, Differential and Integral Approach Applied to Conservation of Mass,
Momentum and Energy Principles..
Page 13 of 22
Concept of Boundary Layer, Boundary Layer over Flat Plates and Tubes, Boundary Layer
Parameters, Boundary Layer Thickness, Momentum Thickness, Displacement Thickness, Von -
Karman Momentum Integral Equation, Boundary Layer Separation and Control, Concept of Drag,
Streamlined and Bluff Bodies.
(Total Lecture Hours: 42)
_____________________________________________________________________________
3. Practicals:
1. Flow of an Incompressible Fluid through an Orifice meter and its calibration for measurement of
discharge.
2. Flow of an Incompressible Fluid through a Nozzle meter and its calibration it for measurement
of discharge.
3. Flow of an Incompressible Fluid through a Venturi Meter and its Calibration for measurement of
discharge.
4. Flow of an Incompressible Fluid through a Centrifugal Head Meter and its Calibration for
measurement of discharge.
5. Forced Vortex flow of water in the vessel.
6. Variation of friction factor with Reynolds number for Laminar flow through circular pipe
7. Variation of friction factor with Reynolds number for Turbulent flow through circular pipe
8. Determination of the velocity distribution in circular pipe.
9. Study of types of Pipes, Pipe symbols, Pipe Fittings and Valves.
4. Books Recommended:
1. F. M. White, Fluids Mechanics, McGraw -Hill Inc., 2015.
2. V. L. Streeter, E. B. Wylie, Fluid Mechanics, McGraw -Hill Book Co. Inc., 2001.
3. A. K. Mohanty, Fluid Mechanics, Prentice -Hall India Private Ltd., 2004.
4. J. F. Douglas, J. M. Gasiorek, J. A. Swaffield, Fluid Mechanics, Pearson Education Pvt. Ltd.,
2001.
5. S. K. Som, G. Biswas, Introduction to Fluid Mechanics and Fluid Machines, Tata McGraw Hill
Co. Pvt. Ltd., 2017.
Page 14 of 22
Heat Transfer
L T P Credit
ME204 3 1 2 05
CO1 Apply appropriate mode of heat transfer while analysing complex engineering problems.
CO2 Compute steady state and transient heat conduction problems in slab, cylindrical and
spherical systems.
CO3 Explore various Nusselt number correlations for forced and free convection systems.
CO4 Calculate surface to surface radiative heat transfer in engineering systems.
CO5 Investigate the performance of heat exchanger using LMTD and NTU-effectiveness
methods.
2. Syllabus
Page 15 of 22
3. Practicals:
4. Books Recommended:
Page 16 of 22
Machine Design and Drawing
L T P Credit
ME206 4 0 4 06
2. Syllabus
Page 17 of 22
3. Practicals:
4. Books Recommended:
Page 18 of 22
Dynamics of Machines
L T P Credit
ME208 3 1 2 05
CO1 Understand the conditions of the static equilibrium and free body diagrams and analyse
different types of governors.
CO2 Apply the knowledge of static and dynamic force analysis in existing mechanisms
CO3 Apply the concept of balancing for rotating and reciprocating unbalanced masses
CO4 Analyze the stability of automobile, naval ship and other related devices considering
gyroscopic effect.
CO5 Design and analysis of the flywheel considering turning moment diagram,
2. Syllabus
BALANCING (09Hours)
Introduction, static balancing, dynamic balancing of several masses in different planes. Balancing of
inline engines, V-engines, radial engines, balancing machines.
3. Practicals:
Page 19 of 22
4. To balance multi-rotor system by experimental and validation with analytical and graphical
method.
5. To prepare the performance characteristic curves on Porter governor.
6. To prepare the performance characteristic curves on Proell governor.
7. To prepare the performance characteristic curves on Watt governor.
8. To find the gyroscopic couple acting on rotating disc.
4. Books Recommended:
1. S. S. Rattan, Theory of Machines, McGraw Hill Education (India) Private Limited, 2009.
2. J.E. Shigley, J. J. Uicker and G. R. Pennock, Theory of Machines and Mechanisms, 3 rd
Edition, Oxford University Press, 2005.
3. R. S. Khurmi and J. K. Gupta, Theory of Machines, S. Chand and Company Ltd., 2003.
4. J.S. Rao, and R.V. Dukkipati, Mechanism and Machine Theory, Wiley Eastern Ltd.,1989
5. A. Ghosh and A. K. Malick, Theory of Mechanisms and Machines, 3rd Edition, East West
Press Pvt. Ltd., 2000.
Page 20 of 22
Industrial Engineering
L T P Credit
ME212 3 0 0 03
CO1 Explain the basics of industrial engineering, identify the factors influencing productivity
and evaluate the productivity.
CO2 Apply the tools of method study and time study for creating the improved process and
timing for doing a job.
CO3 Explain and analyse the factors affecting the plant layout and location decisions.
CO4 Apply qualitative and quantitative techniques for solving the problems of forecasting.
CO5 Apply deterministic and probabilistic inventory control models for evaluating the
inventory level.
CO6 Explain the production systems and functions of production planning and control.
2. Syllabus
Page 21 of 22
HUMAN RESOURCE MANAGEMENT (04 Hours)
Functions of Human Resource Manager, Training and development, Job evaluation and Merit
rating, Wage and Wage Incentives, Grievance handling, Discipline and welfare
(Total Lecture Hours: 42)
_______________________________________________________________________________
3. Books Recommended:
1. J. Heizer, B. Render, C. Munson, and A.Sachan, Operations Management, 12th Edition, Pearson
Education, 2017.
2. E. S. Buffa and R. K. Sarin, Modern Production/ Operations Management, 8th Edition, John Wiley
& Sons, 1987.
3. S. Eilon, Elements of Production Planning and Control, 3rd Edition, Universal Publishing
Corporation, 1991.
4. N.V. S. Raju, Industrial Engineering and Management, 1st Edition, Cengage Learning, 2013.
5. M. Mahajan, Industrial Engineering and Production Management, 1st Edition, Dhanpat Rai & Co.
(P) Limited, 2015.
Page 22 of 22