Professional Documents
Culture Documents
Version : A.001
Issue Date : 2009/03/13
File Name : SP-PS252C-A.001.doc
Total Pages : 10
新竹市科學園區展業一路 9 號 7 樓之 1
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel:886-3-5645656 Fax:886-3-5645626
點晶科技股份有限公司
SILICON TOUCH TECHNOLOGY INC. PS252C
PS252C
2-Channel Secondary Monitoring IC
General Description
PS252C is specially designed for switching power supply system. Four important
functions of PS252C are the followings: over-voltage protection, over-current protection,
under-voltage protection and power good signal generating.
OVP/UVP (Over-Voltage/Under-Voltage Protection) monitors dual 12V to protect
our power supply and PC, FPO/ goes to high when one of these supply voltages
exceeds their normal operation voltage range.
OCP (Over Current Protection) monitors IS12A, IS12B input current sense. An
adjustable over-current condition composed of Iref and “protection current range
resistor” helps users design OCP easily.
An additional protection input pin provides the flexibility for design protection
circuit.
Power good signal generating notifies personal computer when power supply is
ready or power supply is going to shutdown, therefore it can provide a reliable power
supply environment.
Features
• Over/Under-voltage protection and lock out
• Over-current protection and lock out
• Additional protection input
• Fault protection output with open drain output stage
• Open drain power good output signal for power good input
• Built-in 300mS power good delay
• AC on 75ms delay for UV/OC protection
• 38mS PSON/ control de-bounce
• Wide power supply range (3.8V~16V)
• Special care for AC power off
Block Diagram
VS12A
R1
12 UV delay FPO/
S Q
R2 Vref
22uS R
12 OV 1MΩ
R3 Vref delay
38mS
De-bounce
H : 4mS
L : 4.5uS
VS12B
R1
12 UV
VCC
R2 Vref
30KΩ
12 OV VCCI
2KΩ
R3 Vref PSON/
Vref
4.5V 90KΩ
delay
H : 75mS
L : 4.5uS PGI
Selection
PGI
1.25V
VCCI
1MΩ
PGO
delay
73uS
De-bounce
H : 300mS
L : 4.5uS
delay delay
VCCI Pext
1.2V
Step Down 53uS 53uS
12 OC
IS12A to near 2.5V
delay
Iref X 8 Power On Constant Current
POR RI
Reset Source Iref
VCCI H : 20mS
Step Down L : 4.5uS
12 OC
IS12B to near 2.5V
Internal
VCCI = 4V
Power
Iref X 8
VCC VCC
Timing Chart
Vcc
PSON/
FPO/
PGI
VS12A IS12A
VS12B IS12B
Pext
PGO
Td1 Tb1
Td3
Td2
Td1
Td2
Pin Descriptions
Over-Voltage Section
Parameter Conditions MIN TYP MAX Unit
VS12A/B Over-Voltage Threshold 13.3 13.8 14.2 V
Under-Voltage Section
Parameter Conditions MIN TYP MAX Unit
VS12A/B Under-Voltage Threshold 9.8 10.2 10.6 V
Over-Current Section
Parameter Conditions MIN TYP MAX Unit
VS12A/B Offset Voltage -5 0 5 mV
Constant Isink Current (ISINK) 144 160 172 uA
Application
Typical 2 rails SPS
S.P.S. Secondary Side
RS12 A
+12VA Output
+12VA Coil
RS 12 B
+12VB Coil +12VB Output
VDET
R OC12B
R OC12A
R PGO
4.7K
CPGI-1
R PGI-1
C 12A-1 0.1 uF
5 RI VS12A 10
C 12B-1 0.1 uF
6 IS12B IS12 A 9
CPGI-2
RPGI-2
RI
Cby
C PGO 0.1 uF
C 12A-2 0.1 uF
C 12B-2 0.1 uF
Notes:
1. Zener diode or resistor or both of them can be used in component X.
2. The bypass capacitor Cby suggests to be 0.1uF~ 10uF and layout nearby pin VCC.
3. The recommend sense values of RS12A, RS12B are ≥ 0.002Ω.
4. Over-Current Protection design example:
= 62.5 K (Ω )
V 1.25
(1) I ref = 20 μA , RI = RI =
I RI 20μ
(2) RS5=0.002 Ω , ΔV5V = 0.002 × I +5V = ROC 5 × 8 × I ref
0.002 × 20
(3) If 12V OCP trip point is 20A, ROC 5 = = 250(Ω )
8 × 20 μ
Package Specification
( 14-pin DIP )
E1 E eB
θ°
A2 A
Seating Plane
A1 L
b1 b e S
0 5 10 15 20 25 mm
The products listed herein are designed for ordinary electronic applications, such as
electrical appliances, audio-visual equipment, communications devices and so on.
Hence, it is advisable that the devices should not be used in medical instruments,
surgical implants, aerospace machinery, nuclear power control systems,
disaster/crime-prevention equipment and the like. Misusing those products may
directly or indirectly endanger human life, or cause injury and property loss.
Silicon Touch Technology, Inc. will not take any responsibilities regarding the
misusage of the products mentioned above. Anyone who purchases any products
described herein with the above-mentioned intention or with such misused
applications should accept full responsibility and indemnify. Silicon Touch Technology,
Inc. and its distributors and all their officers and employees shall defend jointly and
severally against any and all claims and litigation and all damages, cost and
expenses associated with such intention and manipulation.
Silicon Touch Technology, Inc. reserve the right to make changes to their products or
to discontinue any product or service without notice, and advise customers to obtain
the latest version of relevant information to verify, before placing orders, that
information being relied on is current and complete.