Professional Documents
Culture Documents
Nea Smart Room Control Unit D: Installation and Operating Manual
Nea Smart Room Control Unit D: Installation and Operating Manual
1 Safety 3 More information on the Nea Smart control system and all
1.1 Used symbols 3 documentation available for download can be found at
1.2 Intended use 3
1.3 General safety warnings 3
www.rehau.com/neasmart
2 Versions 4
2.1 Technical data 4
2.2 Compliance 4
3 Installation 5
3.1 Box contents 5
3.2 Installation 5
4 Operation 7
4.1 Overview and displays 7
4.2 Operation 8
4.3 Commissioning (incl. pairing) 8
4.4 Connection test 8
4.5 Comfort programs - Smart Start/Stop mode 8
4.6 Lifestyle functions overview 8
4.7 Lifestyle functions 9
4.8 Overview parameters 9
4.9 Parameters 10
2
1 SAFETY
The Nea Smart room control unit D (in the following abbreviated as
room control unit D) is a room control unit for the base station Nea
Smart 24 V.
3
2 VERSIONS
Nea Smart room control unit D This product is labelled with the CE Marking and thus is in compliance
Floor temperature with the requirements from the guidelines:
Nea Smart remote sensor (optional) - 2004/108/EG with amendments “Council Directive on the approxi-
monitoring
Power supply 24 ... 35 V [via rmBUS] mation of the laws of the Member States relating to Electromagnetic
Compatibility”
BUS connection [rmBUS] polarity reversal protected
- 2006/95/EG with amendments “Council for Coordination of the
Protection type/protection Regulations of EU Member Countries regarding the electrical
IP20 / III
class
equipment for use within certain voltage limits”
Ambient temperature 0 to 50 °C Increased protection requirements may exist for the overall installation,
Ambient humidity 5 to 80%, not condensing the compliance of which is the responsibility of the installer.
Dimensions (HxWxD) 86 x 86 x 26,5 mm
Target temp. setting range 5 bis 30°C
Target temp. resolution 0.2 K
Actual temp. measuring
0 bis 40°C (int. sensor)
range
Measuring accuracy of
±0.3 K
internal NTC
Tab. 2-1 Technical data Nea Smart room control unit D
4
3 INSTALLATION
~30cm
~150cm
Accessories:
Fig. 3-2 Notes on the mounting location of the room control unit
5
1 2 3
4 Ø 3,5 mm 5a 5b
rmBUS
syBUS
Error
Cool
Fuse Pairing Power Pump Boiler
H%
Master NO 1 2 3 4
6
4 OPERATION
Room temperature
Time
Control knob
Fig. 4-1 Front view of the Nea Smart room control unit D
Holiday function
Automatic mode active Flashing: planned
Permanent on: active
7
4.2 Operation 4.5 Comfort programs - Smart Start/Stop mode
The room control unit can be operated via the control knob: Comfort programs include pre-defined heating times to be used for
working days (1-5) or for the weekend (6-7). Outside the heating
Pressing the control knob activates menus and times the installation switches to night mode. You can select the
functions. comfort programs in the Parameter menu. The Smart Start/Stop Mode
Rotation permits the target temperature to be set as of the system calculates the required delay times to reach the
- +
well as navigation between menus and their functions. desired temperature at the starting and finishing time of the heating
program.
A basic level and three menus are available.
Program Comfort time 1 Comfort time 2
Basic level: P0 05:30 – 21:00 –
Rotating adjusts the desired target temperature.
- +
Functions: includes all important lifestyle functions. You can create individual comfort programs with the on-line software
available under www.ezr-home.de and transfer these to the basis
Parameters: includes several parameters as e. g. heating and station with a MicroSD card.
setback temperatures, date and many more.
4.6 Lifestyle functions overview
Service: includes settings for the specialist (secured by PIN,
see manual of the base station) In this menu you can activate or deactivate the lifestyle functions.
1. Press the control knob.
2. Activate the menu “Lifestyle functions” by pressing the control
knob again.
4.3 Commissioning (incl. pairing) 3. Select the desired lifestyle function.
1. Activate the pairing function at the base station for the desired The following lifestyle functions are available to you; you can find
heating zone (see manual base station Nea Smart 24 V). further information in the table “Functions” on the next page.
2. Press the control knob for approx. 3 s. in order to activate pairing
function (the display shows "Set"). It may take up to 10 minutes before changes of global lifestyle
- The base station and the room control unit are connected to functions are displayed on all room control units.
each other.
- If the base station has been programmed before, the date and
time of the room control unit are set automatically.
8
4.7 Lifestyle functions 4.8 Overview parameters
Lifestyle function Symbol Steps This menu is needed only for basic setup.
Party - Activate by pressing. - Press the control knob.
Deactivates the - Set the duration in hours (hh) - Select the menu “Parameters” and activate it by pressing again.
temperature setback for - Confirm your entry by
XX hours pressing. The following parameters are available to you; you can find further
- The automatic mode is only information in the table “Parameters” on the next page.
Presence available on workdays.
Weekend heating times
- Activate by pressing. It may take up to 10 minutes before changes of global system
are also used for working
days - Finish by selecting another parameters are displayed on all room control units.
Lifestyle function.
Day (default setting)
Permanent regulation RES
- Activate by pressing.
according to the set USER
target temperature
XX.X
Night
Permanent setback
according to pro- - Activate by pressing. XX.X
– +
grammed night
temperature.
Automatic XX.X
Automatic temperature
regulation according to
- Activate by pressing.
the correspondingly SET
activated comfort TIME
programs
Deactivates the room P0 min.
- Press in order to switch off the max.
control unit, the
room control unit
6-7
P0 E-CL
temperature is still 1-5 SET
- Press again to switch the room
displayed, frost control unit on again
protection is activated Fig. 4-3 Selection of parameters
Selection of heating or
cooling mode (The CO pilot of the base is
The operating mode can activated.)
be set on the room - Activate by pressing.
control unit D when the - Select the mode.
CO pilot function is - Confirm your entry by
activated on the base. pressing.
- Activate by pressing.
Holiday mode
- Select 1. the start date and
The temperature is
2. the end date (dd:mm)
automatically lowered to
confirm by pressing.
the set holiday
- Deactivate the holiday mode by
temperature
calling the function again.
Child safety lock
- Activate by pressing.
Locks the room
- Deactivate by pressing (>3 s).
operating unit
BACK
The room control unit - Exit the menu by pressing
returns to the basic level.
9
4.9 Parameters
Temperature for - Activate and set the desired - Display of the software
Info software version So3
presence in temperature. version of the Ethernet
Ethernet Controller XX-XX
heating mode - Confirm by pressing. Controller
User level reset
Temperature - Activate and set the desired Reset of all user RES - Activate and select Yes
for presence in temperature. settings to factory USER - Press to reset all functions.
cooling mode - Confirm by pressing. settings!
Tab. 4-4 Parameters
- Activate and set the desired
Setback temperature
temperature.
for heating mode
- Confirm by pressing.
10
5 TROUBLESHOOTING, CLEANING AND
DECOMMISSIONING
Error messages are displayed by, the corresponding symbols in the Only use a dry and solvent-free, soft cloth for cleaning.
display flashing.
5.3 Disposal
Display Meaning Handling
The room control unit must not be disposed with domestic
Connection to - Room control unit paired. waste. The operator has the duty to dispose of the units
- Room control unit tries to
base station through appropriate collection points. The separate
establish a connection to the
faulty base. collection and orderly disposal of all materials will help to conserve
natural resources and ensure a recycling in a manner that protects
- Carry out new pairing of the human health and the environment. If you need information about
Room control
room control unit.
unit not paired. collection points for your devices, please contact your local municipal-
- Contact your electric installer.
ity or your local waste disposal services.
- Re-establish the power supply
Base station to the base station.
switched off - Contact your electric installer in
case of a defect.
Internal
- Replacement necessary,
temperature
Err 0001 contact your electric installer.
sensor defective.
External
- Replacement necessary,
temperature
Err 0002 contact your electric installer.
sensor defective.
- Check the voltage supply of the
Base station not
base station.
found in spite of
- Carry out new pairing of the
Err 0005 successful
room control unit.
pairing
- Contact your electric installer.
Communication - Check the voltage supply of the
between base base station.
Err 0006 stations faulty - Contact your electric installer.
Tab. 5-1 Errors shown on the display
11
Insofar as the intended application deviates from that described in the relevant
Technical Information brochure, the user must consult REHAU and must receive
express written consent from REHAU before commencing this utilization. If the user
fails to do so, the sole responsibility for the utilization shall lie with the individual user.
In this case, the application, use and processing of products are beyond our control.
This document is protected by copyright. All rights based on this are reserved. No part Should a case of liability arise, however, this shall be limited to the value of the goods
of this publication may be translated, reproduced or transmitted in any form or by any delivered by us and used by you in all cases of damage. Claims arising from granted
similar means, electronic or mechanical, photocopying, recording or otherwise, or stored guarantees shall become invalid in the case of intended applications that are not
in a data retrieval system. described in the Technical Information brochures.