Professional Documents
Culture Documents
Pilot’s Guide
& Reference
Foreword
Foreword
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Tel: 913/397.8200 Fax: 913/397.8282
Garmin AT, Inc., 2345 Turner Rd., S.E., Salem, Oregon 97302, U.S.A.
Tel: 503/581.8101 Fax: 503/364.2138
Garmin (Europe) Ltd., Liberty House, Hounsdown Business Park, Southhampton, SO40 9RB, U.K.
Tel: 44/0870.851241 (Europe) Fax: 44/1794.519222
Tel: 0808.2380000 (UK)
Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
Tel: 886/02.2642.9199 Fax: 886/02.2642.9099
Web Site Address: www.garmin.com
This manual reflects the operation of Main System Software versions, 2.00, 3.00, or later. Some differences in opera-
tion may be observed when comparing the information in this manual to earlier or later software versions.
© 2007 Garmin Ltd. or its subsidiaries. All rights reserved. Except as expressly provided herein, no part of this
manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium,
for any purpose without the express written permission of Garmin. Garmin hereby grants permission to down-
load a single copy of this manual and of any revision to this manual onto a hard drive or other electronic storage
medium to be viewed for personal use, provided that such electronic or printed copy of this manual or revision
must contain the complete text of this copyright notice and provided further that any unauthorized commercial
distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Garmin reserves the right to change or improve
their products and to make changes in the content of this material without obligation to notify any person or
organization of such changes or improvements.
September 2007 190-00356-00 Rev. B
INTRODUCTION
Cautions
Introduction
Cautions
CAUTION: The Global Positioning System is operated CAUTION: The electronic chart is an aid to naviga-
by the United States government, which is solely re- tion and is designed to facilitate the use of authorized
sponsible for its accuracy and maintenance. The system government charts, not replace them. Land and water
is subject to changes which could affect the accuracy data is provided only as a general reference to your
and performance of all GPS equipment. Although the surroundings. The positional accuracy of the land and
Garmin 400W-series are precision electronic NAViga- water data is not of a precision suitable for use in
tion AIDs (NAVAID), any NAVAID can be misused or navigation and it should not be used for navigation.
misinterpreted and therefore become unsafe. Only official government charts and notices contain
all information needed for safe navigation – and, as
CAUTION: Use the 400W-series at your own risk. To always, the user is responsible for their prudent use.
reduce the risk of unsafe operation, carefully review
and understand all aspects of this Owner’s Manual and CAUTION: The Terrain feature is for supplemental
the Flight Manual Supplement, and thoroughly practice awareness only. The pilot/crew is responsible for all
basic operation prior to actual use. When in actual use, terrain and obstacle avoidance using information not
carefully compare indications from the 400W-series to provided by the 400W-series Terrain feature.
all available navigation sources, including the informa-
tion from other NAVAIDS, visual sightings, charts, etc. For CAUTION: The Garmin 400W-series does not contain
safety, always resolve any discrepancies before continu- any user-serviceable parts. Repairs should only
ing navigation. be made by an authorized Garmin service center.
Unauthorized repairs or modifications could void your
WARNING: The altitude calculated by the 400W-series warranty and authority to operate this device under
is geometric height above mean sea level and could FCC Part 15 regulations.
vary significantly from altitude displayed by pressure
altimeters in aircraft. NOTE: The GNS 400W-series units use a different
database than in the legacy units. The databases are in-
WARNING: The Jeppesen database incorporated in compatible between units. The GNS 400W-series units
the 400W-series must be updated regularly in order must use a WAAS enabled database.
to ensure that its information is current. Updates are
released every 28 days. A database information packet NOTE: This product, its packaging, and its components
is included in your 400W-series package. Pilots using contain chemicals known to the State of California to
an out-of-date database do so entirely at their own cause cancer, birth defects, or reproductive harm. This
risk! notice is being provided in accordance with California’s
Proposition 65. If you have any questions or would like
CAUTION: GPS receivers operate by receiving and additional information, please refer to our website at
decoding very low power radio signals broadcast by www.garmin.com/prop65.
satellites. It is possible that in some situations other
radio equipment or electronic equipment used in close NOTE: It is the pilot’s responsibility for initial missed
proximity to a GPS receiver may create electromagnetic approach guidance in accordance with published pro-
interference (EMI) which may affect the ability of the cedure. The unit may not provide correct guidance until
GPS receiver to receive and decode the satellite signals. established on a defined leg.
In such event, the interference may be reduced or
eliminated by switching off the source of interference
or moving the GPS receiver away from it.
190-00356-00 Rev B
INTRODUCTION
Cautions
NOTE: This device complies with Part 15 of the FCC limits for To obtain accessories for your 400W-series, please contact
Class B digital devices. This equipment generates, uses, and your Garmin dealer.
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful Help us better support you by completing our on-line registra-
interference to radio communications. Furthermore, there is tion form today! Registration ensures that you will be notified
no guarantee that interference will not occur in a particular of product updates and new products and provides lost or sto-
installation. len unit tracking. Please, have the serial number of your unit
handy, connect to our web site (www.garmin.com) and look for
If this equipment does cause harmful interference, the user is our Product Registration link on the home page.
encouraged to try to correct the interference by relocating the
equipment or connecting the equipment to a different circuit The 400W-series display lenses are coated with a special anti-
than the affected equipment. Consult an authorized dealer or reflective coating which is very sensitive to skin oils, waxes
other qualified avionics technician for additional help if these and abrasive cleaners. It is very important to clean the lens
remedies do not correct the problem. using an eyeglass lens cleaner which is specified as safe for
anti-reflective coatings and a clean, lint-free cloth.
Operation of this device is subject to the following conditions:
(1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation.
ii 190-00356-00 Rev B
INTRODUCTION
Accessories and Packing List
Limited Warranty
This Garmin product is warranted to be free from defects in materials or workmanship for two years from the
date of purchase. Within this period, Garmin will, at its sole option, repair or replace any components that fail in
normal use. Such repairs or replacement will be made at no charge to the customer for parts and labor, provided
that the customer shall be responsible for any transportation cost. This warranty does not cover failures due to
abuse, misuse, accident, or unauthorized alterations or repairs.
THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL
OTHER WARRANTIES EXPRESS OR IMPLIED OR STATUTORY, INCLUDING ANY LIABILITY ARISING UNDER
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, STATUTORY OR
OTHERWISE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH MAY VARY FROM STATE TO
STATE.
IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSE-
QUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE, OR INABILITY TO USE THIS
PRODUCT OR FROM DEFECTS IN THE PRODUCT. Some states do not allow the exclusion of incidental or
consequential damages, so the above limitations may not apply to you.
Garmin retains the exclusive right to repair or replace the unit or software, or to offer a full refund of the pur-
chase price, at its sole discretion. SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY
BREACH OF WARRANTY.
To obtain warranty service, contact your local Garmin Authorized Service Center. For assistance in locating
a Service Center near you, visit the Garmin Web site at “http://www.garmin.com” or contact Garmin Customer
Service at 800-800-1020.
iv 190-00356-00 Rev B
INTRODUCTION
Table of Contents
190-00356-00 Rev B
INTRODUCTION
vi 190-00356-00 Rev B
INTRODUCTION
Blank Page
190-00356-00 Rev B
TAKEOFF TOUR
Key and Knob Functions
}
O The OBS key is used to select manual or
automatic sequencing of waypoints. Pressing
scroll bar
the OBS key selects OBS mode, which will
retain the current “active to” waypoint as
your navigation reference even after pass-
ing the waypoint (i.e., prevents sequencing
Whenever the 400W-series unit is dis-
to the next waypoint). Pressing the OBS playing a list of information that is too
key again will return to normal operation, long for the display screen, a scroll bar
with automatic sequencing of waypoints. will appear along the right-hand side
Whenever OBS mode is selected, you may set of the display. The scroll bar graphically
indicates the number of additional items
the desired course to/from a waypoint using
available within the selected category.
the OBS Page, or an external OBS selector on
your HSI or CDI. Simply press the small right knob to
activate the cursor and turn the large
M The message key (MSG) is used to view right knob to scroll through the list.
system messages and important warnings and
requirements. See Sections 11 and 9 for more
information on messages and unit settings. P The procedures key (PROC) allows you to
select and remove approaches, departures
The flight plan key (FPL) allows you to and arrivals from your flight plan. When
create, edit, activate and invert flight plans, using a flight plan, available procedures for
F
as well as access approaches, departures and your departure and/or arrival airport are
arrivals. A closest point to flight plan feature offered automatically. Otherwise, you may
is also available from the flight plan key. See select the desired airport, then the desired
Section 4 for more information on flight procedure.
plans.
190-00356-00 Rev B
TAKEOFF TOUR
Power On
Power-up Sequence
190-00356-00 Rev B
TAKEOFF TOUR
Instrument Panel Self-Test
{ }
Check CDI/HSI, Fuel Figures: May be
RMI and other entered manually if no
instruments sensor present
to verify these
indications Select to Set Fuel Level
to Full Capacity
Instrument Panel Self-Test To enter fuel capacity, fuel on board or fuel flow
figures (if not provided by sensors):
Once the database has been acknowledged, the
instrument panel self-test page will appear. To ensure 1. Turn the large right knob to select the “CAP”,
that your 400W-series unit and any connected instru- “FOB” or “FF” field.
ments are working properly, check for the following 2. Turn the small and large right knobs to enter
indications on your CDI/HSI, RMI, external annuncia- the desired figure, then press ENT.
tors and other connected instruments:
• Course deviation
• Glideslope
• TO/FROM flag
• Time to destination
• Bearing to destination
• Desired track
• Distance to dest.
• Ground speed
• All external annunciators (if installed)
The instrument panel self-test page indicates the cur-
rently selected OBS course, fuel capacity (CAP), fuel
on board (FOB) and fuel flow (FF). The fuel capacity,
fuel on board and fuel flow may be manually entered Enter the fuel capacity, fuel on board or fuel
if your installation does not include connection to sen- flow figures directly onto the appropriate
field of the instrument panel self-test page.
sors which automatically provide these figures.
These figures will automatically be provided
if your installation includes connection to
external sensors.
190-00356-00 Rev B
TAKEOFF TOUR
Fuel On Board & Checklists
190-00356-00 Rev B
TAKEOFF TOUR
Acquiring Satellites / Messages
Acquiring Satellites/Messages
If the 400W-series unit has not been operated for a
period of six months or more, it may have to “Search
the Sky” to collect new data. This means the unit is
acquiring satellite data to establish almanac and satel-
lite orbit information, which can take 5 to 10 minutes.
The Satellite Status Page displays a “Searching Sky” The satellite status page shows the ID num-
status, and the message annunciator (MSG) above the bers for the satellites and the relative signal
MSG key also flashes to alert you of a system message, strength of each satellite received (as a “bar
“Searching the Sky”. graph” reading.
The Time and other data may not be displayed “Searching Sky” indicates that satellite almanac
until the unit has acquired enough satellites for a fix. data is not available. The data is recollected from the
first available satellite.
To view a system message, press the MSG key. “Acquiring” indicates that satellites have been
located and information is being acquired, but the
receiver does not have enough satellites for a 3-dimen-
sional position.
“3D NAV” indicates that a 3-dimensional position
is available.
Message Page
“3D DIFF NAV” indicates when a 3-dimensional
position is available and differential corrections are
The message page will appear and display the status being used.
or warning information applicable to the receiver’s cur- The “INTEG” annunciator (bottom left corner of
rent operating condition. the screen) indicates that satellite coverage is insuffi-
To return to the previous page after viewing a cient to pass built-in integrity monitoring tests.
message, press the MSG key again.
190-00356-00 Rev B
TAKEOFF TOUR
420W / 430W Only Selecting COM and VLOC Frequencies
Selecting COM and VLOC Frequencies Once you’ve entered the active frequency, simply
While the 400W-series unit is acquiring a position, repeat steps 1 through 3, above, to enter the standby
let’s take a minute to dial in the active and standby frequency. After both communication frequencies have
been entered, you may elect to keep the COM window
frequencies you’ll be using for the first phase of your
‘hot’ by leaving the cursor on the standby frequency, or
flight. The 400W-series display is divided into separate
move the cursor to the VLOC window by pressing the
“windows” (or screen areas), including a COM window, small left knob.
VLOC window, and the GPS window.
COM Window:
Once you’ve entered the active frequency, simply
Active Frequency repeat steps 1 to 3, above, to enter the standby fre-
COM Window:
Standby Frequency quency. After both communication frequencies have
VLOC Window: been entered, you may elect to keep the COM window
Active Frequency with tuning cursor
“hot” by leaving the cursor on the standby frequency,
or move the cursor to the VLOC window by pressing
Pushing the small left knob activates the tuning the small left knob.
cursor in the desired frequency window. To select the
NOTE: When selecting VLOC frequencies, the
active frequency, you must first enter the frequency tuning cursor automatically returns to the COM
in the standby field, and use the COM flip-flop (or window after 30 seconds of inactivity.
VLOC flip-flop) key to move it to the active field.
To change the standby communication (COM) or These features are only available in the 420W/430W
VLOC frequency: units.
1. If the tuning cursor is not currently in the
desired window (COM or VLOC), press the
small left knob momentarily to switch the
highlight between the COM and VLOC win-
dows. Adjusting the frequencies with the large
and small left knobs will affect the standby
frequency.
2. Turn the large left knob to select the desired
megahertz (MHz) value. For example, the
“135” portion of the frequency “135.325”.
3. Turn the small left knob to select the desired
kilohertz (kHz) value. For example, the “.325”
portion of the frequency “135.325”.
4. To activate the selected frequency, press the
appropriate flip-flop key—COM for commu-
nication frequencies or VLOC for VOR/Localizer
frequencies.
190-00356-00 Rev B
TAKEOFF TOUR
Page Groups
Page Groups
d
(Large right knob to change page groups)
Map
Arpt Runway Intersection
a
Terrain
Arpt Frequency NDB
NAVCOM
Arpt Approach VOR
Position
Satellite Status
VNAV
Selection of any main page is performed using the large and small right knobs. The large right knob selects the page group: NAV, WPT, AUX or
NRST. The small right knob selects the desired page within a group. To quickly select the default NAV page, press and hold the CLR key.
10 190-00356-00 Rev B
TAKEOFF TOUR
Page Groups
d
(Large right knob to change page groups)
190-00356-00 Rev B 11
TAKEOFF TOUR
Nav Pages
Nav Pages
The map page is one of seven, or more, pages avail-
able under the NAV group*:
• Default NAV page • Map page
• Terrain page • NAVCOM page
• Position page • Satellite status page
• Vertical navigation page The bottom right corner of the screen
To select the desired NAV page, turn the small indicates the page group currently being
right knob until the desired page is displayed. displayed (e.g., NAV or NRST), the number
of screens available within that group
If you are currently viewing a page that is not part (indicated by square icons) and the place-
of the NAV group, you can quickly return to the NAV ment of the current screen within that group
group using the CLR key. (indicated by a highlighted square icon). To
select a different page within the group, turn
To select the NAV group and display the default
the small right knob.
NAV page, press and hold CLR.
NAV WPT
* Seven, or more, NAV Pages are avail-
7+ available pages* 10 available pages able when the 400W-series installation
(see list above) (see Section 6) includes connection to traffic, XM radio,
and/or weather information sources. See the
AUX NRST 400W/500W Series Display Interfaces Pilot’s
4 available pages 8 available pages Guide Addendum, part number
(see Section 9) (see Section 7) 190-00356-31 and the 400W/500W Series
MAIN PAGE GROUPS Garmin Optional Displays Pilot’s Guide Ad-
dendum, part number 190-00356-30.
In addition to the NAV group of pages, additional
groups of pages are available for waypoint information
(WPT), auxiliary (AUX) functions such as flight plan-
ning or unit settings, and listings for nearest (NRST)
airports or other facilities.
To select the desired page group, turn the large
right knob until a page from the desired group is
displayed.
To select the desired page within the group, turn
the small right knob until the desired page is
displayed.
12 190-00356-00 Rev B
TAKEOFF TOUR
Default Nav Page
Default Nav Page To change the data fields in the corners of the
Default NAV Page:
During most flights, the default NAV, map and
NAVCOM pages will be the primary pages used for 1. Press MENU (with the Map Page displayed).
navigation. The default NAV page displays a graphic 2. Turn the large right knob to highlight
course deviation indicator (CDI), the active leg of “Change Fields?” and press ENT.
your flight plan (as defined by the current “from” and 3. Turn the large right knob to highlight the
“to” waypoints), and six user-selectable data fields. data field you wish to change.
The default settings for these fields are distance to
waypoint (DIS), desired track (DTK), bearing to
waypoint (BRG), ground speed (GS), ground track
(TRK) and estimated time en route (ETE). See Sec-
tion 11 for definitions of these navigation terms. The
default NAV page is selected by pressing and holding
the CLR key or turning the small right knob.
4. Turn the small right knob to select the type
Active Leg of of data you want to appear on this field and
Flight Plan Course Deviation Indicator (CDI)
press ENT.
User-
selectable
Data Fields
190-00356-00 Rev B 13
TAKEOFF TOUR
Map Page
Map Page
The map page displays your present position (using
an airplane symbol) relative to nearby airports, VORs,
NDBs, intersections, user waypoints and airspace
boundaries—and your route displayed as a solid line.
Data fields for destination waypoint (WPT), distance
to waypoint (DIS), desired track (DTK) and ground The map page combines a moving map
speed (GS) appear on the right hand side of the display and navigation data for complete
display. These fields are user-selectable to allow you to situational awareness. Map setup pages
configure the unit to your own preferences. Available are provided to designate the maximum
scale at which each map feature will ap-
settings include: altitude, bearing, en route safe alti- pear. These settings provide an automatic
tude, estimated time of arrival, minimum safe altitude, decluttering of the map (based upon your
and ground track. See Section 11 for definitions of preferences) as you adjust the scale.
these navigation terms.
While viewing the map page, you can
Map Display quickly declutter and remove many of
the background map details by pressing
the CLR key (repeatedly) until the desired
Data
detail is depicted.
Fields
To change the map scale, press the or
sides of the RNG key.
14 190-00356-00 Rev B
TAKEOFF TOUR
NAVCOM Page
190-00356-00 Rev B 15
TAKEOFF TOUR
Direct-To Navigation
16 190-00356-00 Rev B
TAKEOFF TOUR
IFR Procedures
190-00356-00 Rev B 17
TAKEOFF TOUR
Nearest Pages
18 190-00356-00 Rev B
TAKEOFF TOUR
Nearest Airport
Additional information for a nearby airport To select a nearby airport as a new destina-
is available by highlighting an identifier on tion, highlight its identifier, press direct-to,
the list and pressing ENT. ENT, and ENT (again).
190-00356-00 Rev B 19
TAKEOFF TOUR
Nearest Airspace
22 190-00356-00 Rev B
1 - COM
Radio Volume / Auto Squelch
420W / 430W Only
Section 1 Squelch
Communicating Using the The COM radio features an automatic squelch to
GNC 420W/AW and GNS 430W/AW reject many localized noise sources. You may override
the squelch function by pressing the COM power/
Some models of the 400W-series feature a digitally- volume knob. This facilitates listening to a distant sta-
tuned VHF COM radio that provides a seamless transi- tion or setting the desired volume level.
tion from communication to navigation. The GNC
420W and GNS 430W’s COM radio operates in the
aviation voice band, from 118.000 to 136.975 MHz,
in 25 kHz steps (default). For European operations, a
COM radio configuration of 8.33 kHz steps is pro-
vided (Section 9 - Aux - Setup 2). The GNC 420AW
and GNS 430AW use a 16-watt transmitter, instead of Press the COM power/volume knob momen-
the standard 10-watt transmitter. tarily to override the automatic squelch.
Note the “RX” receive indication when
receiving a station.
To override the automatic squelch, press the COM
power/volume knob momentarily. Press the COM
power/volume knob again to return to automatic
squelch operation.
Volume
COM radio volume is adjusted using the COM
power/volume knob. Turn the COM power/volume
knob clockwise to increase volume, or counterclock-
wise to decrease volume.
190-00356-00 Rev B 23
1 - COM
Com Window and Tuning 420W / 430W Only
24 190-00356-00 Rev B
1 - COM
420W / 430W Only Auto-Tuning from Nearest Airport Page
190-00356-00 Rev B 25
1 - COM
Auto-Tuning from Flight Plan/Database 420W / 430W Only
To select a COM frequency for a nearby flight ser- 2. Press the small right knob to place the cursor
vice station (FSS) or center (ARTCC): on the airport identifier field. To the left of this
1. Select the nearest center or flight service page field appears Departure, En Route or Arrival
from the NRST page group. Turn the large — depending on the placement of the dis-
right knob until the NRST pages appear. Then, played airport within your flight plan.
if necessary, turn the small right knob to 3. Turn the small right knob to display a
display the desired NRST page. window listing the airports in your flight plan.
Continue turning the small right knob to
select the desired airport.
4. Press ENT to return to the NAVCOM page with
the frequencies for the selected airport.
5. Turn the large right knob to highlight the
desired frequency.
Use the nearest ARTCC page to quickly re-
trieve the frequency(s) for the nearest center 6. Press ENT to place the highlighted frequency
(ARTCC) facility. in the standby COM window field.
2. Press the small right knob momentarily to To select a COM frequency for any airport in the
database:
place the cursor on the page.
1. Select the airport frequencies page from the
3. Turn the large right knob to highlight the
FSS/ARTCC frequency and press ENT to place WPT page group. (Turn the large right knob
the frequency in the standby field of the COM to select the WPT page group. Then turn the
window. small right knob until the airport frequencies
page appears.)
To select a COM frequency for any airport in your
flight plan:
1. Select the NAVCOM page from the NAV page
group. (Press and hold the CLR key, then turn
the small right knob until the NAVCOM page
appears.)
190-00356-00 Rev B 27
1 - COM
Remote Frequency Selection
28 190-00356-00 Rev B
2 - NAV PAGES
Page Groups / NAV Page Group
Section 2
NAV Pages
Main Page Groups Default NAV Map Terrain
AUX NRST
4 available pages 8 available pages
(see Section 9) (see Section 7) The bottom right corner of the screen indicates which page
group is currently being displayed (e.g., NAV or NRST), the
To select the desired page group, turn the large number of screens available within that group (indicated by
right knob until a page from the desired group is square icons) and the placement of the current screen within
displayed. that group (indicated by a highlighted square icon). To select a
To select the desired page within the group, turn different page within the group, turn the small right knob.
the small right knob until the desired page is
displayed.
NAV Page Group
The NAV page group includes seven, or more,
pages. While viewing any NAV page, turn the small
right knob to select a different NAV page. You may
find this selection process convenient to cycle between This part of the screen is also used to display the 400W-series
the default NAV and map pages—two of the most turn advisories (e.g., “DTK 313° 9 S”, or LT TO 030° NOW) and
frequently used pages. Other pages are provided to waypoint alerts (e.g., “ARRIVING WPT” or “HOLD TEARDROP”)
during flight plan and approach operations. Seconds will be
list frequencies for your flight plan, show your current
abbreviated as “S” and Now may be seen as “N”. See Section
position, display current satellite reception, and make 5 for more information.
vertical navigation settings.
190-00356-00 Rev B 29
2 - NAV PAGES
Default Nav Page
Default NAV Page The graphic CDI shows your position at the center
The first NAV page is the default NAV page. This of the indicator, relative to the desired course (the
page may be quickly selected from ANY page by using moving course deviation needle). As with a traditional
the CLR key. mechanical CDI, when you’re off course simply steer
toward the needle. The TO/FROM arrow in the center
To select the NAV group and display the default NAV
page, press and hold the CLR key. of the scale indicates whether you are heading to the
waypoint (an up arrow) or if you have passed the
The default NAV page displays a graphic course
waypoint (a down arrow).
deviation indicator (CDI) across the top of the page.
Unlike the angular limits on a CDI coupled to a VOR
or ILS receiver, full scale limits for this CDI are defined The following symbols are used—on the default
NAV page directly below the CDI—to depict the
by a GPS-derived distance (2.0, 1.0 or 0.3 NM). By
“active leg” of a flight plan or direct-to:
default, the CDI scale automatically adjusts to the
desired limits based upon the current phase of flight: Direct-To a Waypoint
en route, terminal area or approach.
Course to a Waypoint, or Desired
Active Leg of Course Deviation Indicator (CDI) Course between Two Waypoints
Flight Plan
Right Procedure Turn
User- Vectors-To-Final
selectable
Data Fields DME Arc to the left
30 190-00356-00 Rev B
2 - NAV PAGES
Default Nav Page
Selecting Desired On-Screen Data To select a different data item for any data field:
At the bottom of the default NAV page you’ll find 1. Starting with the default NAV page, press the
six user-definable fields which display the data you’ll MENU key to display an options menu.
need as your flight progresses. By default these fields 2. The “Change Fields?” option is already high-
display: distance to destination (DIS), desired track lighted, so press ENT to select this option.
(DTK), bearing to destination (BRG), ground speed
(GS), ground track (TRK) and estimated time en route
(ETE). However, each of these fields can be custom-
tailored to your preferences by selecting a different
data item. Available data items include:
• Bearing to destination (BRG)
• Distance to destination (DIS) 3. Use the large right knob to highlight the data
field you wish to change.
• Desired track (DTK)
• En route safe altitude (ESA)
• Estimated time of arrival (ETA)
• Estimate time en route (ETE)
• Fuel Flow (FLOW) (When Configured)
• Ground speed (GS) 4. Turn the small right knob to display the list
• Minimum safe altitude (MSA) of available data items. Continue turning the
small right knob to select the desired data
• Track angle error (TKE) item from the list.
• Ground track (TRK)
• Vertical speed required (VSR)
• Cross track error (XTK)
If no flight plan or direct-to destination has been
selected only speed, track, altitude and minimum
safe altitude data may be displayed. All other data
types will appear as blank lines—on the default NAV 5. Press ENT to select the desired data item and
page—until a destination is selected. return to the default NAV page.
6. Press the small right knob momentarily to
remove the cursor from the page.
190-00356-00 Rev B 31
2 - NAV PAGES
Map Page
32 190-00356-00 Rev B
2 - NAV PAGES
Map Page
VOR/DME TACAN
DME NDB
Heliport
190-00356-00 Rev B 33
2 - NAV PAGES
Map Page
Map Page Auto Zoom To quickly declutter the map display, press the CLR key
momentarily (as often as needed) to select the desired
An autozoom feature is available which will auto- amount of map detail.
matically adjust from an en route range of 200 NM
through each lower range, stopping at a range of The right-hand side of the map page includes four
1.0 NM as you approach your destination waypoint. user-selectable data fields. By default, the displayed
The autozoom feature is turned on/off from the map data is: destination waypoint name (WPT), desired
setup page. track (DTK), distance to destination waypoint (DIS)
and ground speed (GS). Any of these data fields may
The map page also displays a background map
be changed to display a different data type. You may
showing lakes, rivers, coastlines, highways, railways
also remove the four data fields from the map to show
and towns. When a map scale is selected below the
a larger map image.
lower limit at which the map detail was originally cre-
ated, an “overzoom” indication will appear on the map
display, below the scale reading. “Overzoom” indicates
that the detail at this scale may not accurately repre-
sent actual conditions. If you continue to zoom in to
lower scale settings, “overzoom” will be replaced with
“no map” and the geographic detail is removed from
the map display (but, the airport and navaid detail will
remain).
The “Setup Map?” option allows you to define the
maximum scale at which each map feature will appear.
This provides you with complete control to minimize
screen clutter. You can also quickly remove items from
the map using the CLR key.
The CLR key allows you to quickly declutter
the map display, providing four levels of
map detail. Note the “-1” and “-2” (“-3” is
also provided) suffix designations above,
indicating each successive declutter level.
34 190-00356-00 Rev B
2 - NAV PAGES
Map Page
190-00356-00 Rev B 35
2 - NAV PAGES
Map Page
Map Direct-To
To designate an on-screen airport, navaid or user
waypoint as your direct-to destination:
1. Use the panning function (see previous page)
to place the target pointer on a waypoint.
2. Press direct-to key to display the select direct-
to waypoint page, with the selected waypoint 2. Press ENT to display an options menu.
already listed.
3. “Review Airspace?” should already be high-
lighted, if not select it with the small right
knob. Press ENT to display the airspace infor-
mation page for the selected airspace.
36 190-00356-00 Rev B
2 - NAV PAGES
Map Page Options
190-00356-00 Rev B 37
2 - NAV PAGES
Map Page Options
38 190-00356-00 Rev B
2 - NAV PAGES
Map Page Options
7. For airspace boundaries, highways, roads, the top of the map display.
railroad lines, wind vector, track log data,
active flight plan course lines, and lat/long
grid lines: turn the small right knob to select
the appropriate “Group” name (per the chart
on the previous page) and press ENT. Use the
large right knob to highlight the zoom field
for the desired feature and turn the small
right knob to select the maximum scale at 4. To exit the “Measure Dist?” option, press the
which the feature should appear on screen. Or small right knob.
select “Off” to never display the selected fea-
ture. Press ENT to accept the selected option.
Distance Measurements
The “Measure Dist?” option provides a quick, easy
method for determining the bearing and distance
between any two points on the map display.
To measure bearing and distance between two
points:
1. On the Nav Map page, press MENU. Then,
turn the large right knob to highlight “Mea-
sure Dist?” and press ENT. An on-screen refer-
ence pointer will appear on the map display at
your present position.
40 190-00356-00 Rev B
2 - NAV PAGES
Terrain Operation
190-00356-00 Rev B 41
2 - NAV PAGES
Terrain Operation
NOTE: The data contained in the TERRAIN databases International Standard Atmosphere (ISA) model (where
comes from government agencies. Garmin accurately pressure, temperature, and lapse rates have fixed values),
processes and cross-validates the data but cannot it is common for the baro-corrected altitude (as read from
guarantee the accuracy and completeness of the data. the altimeter) to differ from the GPS-MSL altitude. This
TERRAIN Alerting variation results in the aircraft’s true altitude differing from
TERRAIN uses information provided from the GPS the baro-corrected altitude.
receiver to provide a horizontal position and altitude. Terrain Page
GPS altitude is derived from satellite measurements. GPS To display the TERRAIN Page, select the NAV
altitude is converted to a mean sea level (MSL)-based group and turn the small right knob until the
altitude (GPS-MSL altitude) and is used to determine TERRAIN Page is displayed. The page displays terrain
TERRAIN alerts. GPS-MSL altitude accuracy is affected information, aircraft ground track, and GPS-derived
by factors such as satellite geometry, but it is not subject MSL altitude. Altitude is shown in increments of 20
to variations in pressure and temperature that normally feet or in increments of 10 meters, depending on unit
affect pressure altitude devices. GPS-MSL altitude does configuration. The “G” to the right of the MSL altitude
not require local altimeter settings to determine MSL display reminds the pilot that altitude is GPS-derived.
altitude. Therefore, GPS altitude provides a highly accurate
and reliable MSL altitude source to calculate terrain and The TERRAIN Page has two selectable view
obstacle alerts. settings:
TERRAIN utilizes terrain and obstacle databases that • 360˚ View—View from above aircraft depicting
are referenced to mean sea level (MSL). Using the GPS surrounding terrain on all sides
position and GPS-MSL altitude, TERRAIN displays a 2-D • 120˚ View—View of terrain ahead of and 60˚ to
picture of the surrounding terrain and obstacles relative either side of the aircraft flight path
to the position and altitude of the aircraft. Furthermore,
the GPS position and GPS-MSL altitude are used to
calculate and “predict” the aircraft’s flight path in relation
to the surrounding terrain and obstacles. In this manner,
TERRAIN can provide advanced alerts of predicted
dangerous terrain conditions. Detailed alert modes are
described later in this section.
Baro-Corrected Altitude TERRAIN Page
Baro-corrected altitude (or indicated altitude) is derived
NOTE: The TERRAIN Page gives a “Track Up” dis-
by adjusting the altimeter setting for local atmospheric play orientation, as indicated by the “TRK” label
conditions. The most accurate baro-corrected altitude shown on the display. This is the only orientation
can be achieved by frequently updating the altimeter available on this page.
setting to the nearest reporting station along the flight
path. However, because actual atmosphere conditions
seldom match the standard conditions defined by the
42 190-00356-00 Rev B
2 - NAV PAGES
Terrain Operation
To inhibit TERRAIN:
1. Select the TERRAIN Page and press MENU.
“Inhibit Terrain?” is selected by default.
2. Press ENT. The TERRAIN system is inhibited.
The annunciation is displayed in
the terrain annunciator field whenever terrain
is inhibited.
190-00356-00 Rev B 43
2 - NAV PAGES
Terrain Operation
Terrain/Obstacle above or
Red
within 100 ft below current
(Warning)
aircraft altitude
Terrain/Obstacle between
Yellow
100 ft and 1000 ft below the
(Caution)
aircraft altitude
Terrain Color Symbology
����������������������
��������������������� 4ERRAIN ABOVE OR
WITHIN FT
£ääÊvÌÊ/
ÀiÃ
`Ê BELOW THE AIRCRAFT
������������������ ALTITUDE 2ED
£äääÊvÌÊ
4ERRAIN BETWEEN FT AND FT BELOW THE
AIRCRAFT ALTITUDE 9ELLOW
4ERRAIN MORE THAN FT BELOW THE AIRCRAFT ALTITUDE "LACK
44 190-00356-00 Rev B
2 - NAV PAGES
Terrain Operation
190-00356-00 Rev B 45
2 - NAV PAGES
Terrain Operation
To update the terrain or obstacle database: CAUTION: Obstacles 200 feet and higher are in-
1. Acquire a new terrain data card from cluded in the Obstacle Database. It is very impor-
tant to note that not all obstacles are necessarily
Garmin. charted and therefore may not be contained in
2. Turn off the power to the 400W Series unit. the Obstacle Database.
3. Remove the old terrain data card from and Navigation Database
insert the new card into the right-most slot of It is therefore important to also have the latest
the 400W Series unit. Navigation Database installed to ensure correct Terrain
4. Turn on the 400W Series unit and verify that the alerting.
TERRAIN system passes the self-test. The “TER
TERRAIN Alerts
TEST” annunciator will clear after checking and
no failure message appears. TERRAIN alerts are issued when flight conditions
meet parameters that are set within the TERRAIN system
Terrain/Obstacle Database Areas of Coverage
software algorithms. When an alert is issued, visual
The following describes the area of coverage avail- annunciations are displayed. Annunciations appear in a
able in each database. Regional definitions may change dedicated field in the lower left corner of the display.
without notice. TERRAIN Annunciation Field TERRAIN Pop-Up Alert
Database Coverage Area
Latitudes: N 75° to S 60°
Worldwide (WW)
Longitudes: W 180° to E 180°
Limited to the United States plus
United States (US) some areas of Canada, Mexico,
TERRAIN Annunciation and Pop-Up
Caribbean, and the Pacific.
Alert
Alaska, Austria, Belgium, Canada*,
Caribbean*, Czech Republic, Pop-up Alerts
Denmark, Estonia, Finland, France, On any page except the TERRAIN Page, when a terrain
Germany, Greece, Hawaii, Iceland, or obstacle alert is issued, a pop-up window is displayed
US/Europe Ireland, Italy, Latvia, Lithuania, with the appropriate alert.
Mexico*, Netherlands, Norway, To acknowledge the pop-up alert and return to
Poland, Portugal, Slovakia, Spain, the currently viewed page:
Sweden, Switzerland, United Press the CLR key.
Kingdom, United States
To acknowledge the pop-up alert and quickly
* Indicates partial coverage display the TERRAIN Page:
Press the ENT key.
46 190-00356-00 Rev B
2 - NAV PAGES
Terrain Alerts
190-00356-00 Rev B 47
2 - NAV PAGES
Terrain Alerts
(EIGHT !BOVE 4ERRAIN &EET
0$! !LERTING !REA
2UNWAY
4HRESHOLD
$ISTANCE &ROM $ESTINATION !IRPORT NM
Premature Descent Alerting (PDA) Threshold
48 190-00356-00 Rev B
2 - NAV PAGES
Terrain Alerts
190-00356-00 Rev B 49
2 - NAV PAGES
Terrain Alerts
50 190-00356-00 Rev B
2 - NAV PAGES
NAVCOM Page
NAVCOM Page
The NAVCOM (navigation communications) page
provides a list of the airport communication and
navigation frequencies at your departure, en route and
arrival airports. The NAVCOM page makes selection
of the frequencies you’ll need along your flight plan
quick and convenient. If you do not have an active
flight plan with a departure airport, the NAVCOM page To scroll through the list of frequencies:
will display the frequencies for the airport nearest 1. Activate the cursor, if not already active, by
your departure position. Only the 420AW and 430AW pressing the small right knob.
move frequencies to their Navcom. 2. Turn the large right knob to move the cursor
Departure, En through the list of frequencies. If there are more
Route or Arrival frequencies in the list that can be displayed on
Airport the screen, a scroll bar along the right-hand
side of the screen will indicate which part of
Frequency
Type the list is currently being displayed.
}
Third Page
Assigned Frequency
scroll bar
in NAV group
and Usage Informa-
tion (when applicable)
52 190-00356-00 Rev B
2 - NAV PAGES
Position Page
NOTE: Do not rely solely on MSA as an absolute 6. Press the small right knob momentarily to
measure of safe altitude. Consult current charts remove the cursor from the page.
and NOTAMs for your area.
The position page also features a reference
To change the user-selectable data fields: waypoint field, located at the bottom of the page, to
1. Press MENU to display the Position page indicate your bearing and distance to/from a selected
options menu. waypoint. The reference waypoint field can display
2. Turn the large right knob to highlight bearing and distance information for a nearby airport
“Change Fields?” and press ENT. (default), VOR, NDB, intersection or user waypoint.
To change the reference waypoint information:
1. Press MENU to display the position page
options menu.
2. Turn the large right knob to highlight
“Change Fields?” and press ENT.
3. Turn the large right knob to highlight the
3. Turn the large right knob to highlight the waypoint type field (bottom left corner of the
data field you wish to change. page; default setting will show “APT”).
4. Turn the small right knob to display the list of
available waypoint types. Continue turning the
small right knob to select the desired data
item from the list.
54 190-00356-00 Rev B
2 - NAV PAGES
Satellite Status Page
Satellite Status Page (at top left corner of the page) shows which satel-
The Satellite Status Page is helpful in troubleshoot- lites are currently in view, and where they are. The
ing weak (or missing) signal levels due to poor satellite outer circle of the sky view represents the horizon
coverage or installation problems. You may wish to (with north at top of the page); the inner circle 45°
refer to this page occasionally to monitor GPS receiver above the horizon; and the center point directly
performance and establish a normal pattern for system overhead.
operation. Should problems occur at a later date, you The “D” character inside the bars indicates differ-
may find it helpful to have an established baseline ential corrections (e.g. WAAS) are being used for that
from which to compare. satellite.
GPS Receiver
Sky View Status
of satellite
positions Horizontal Figure of Merit
and Vertical Figure of Merit
Signal Estimated Posi-
Strength Bars tion Uncertainty
Vertical Navigation Page
The 400W-series vertical navigation page (the last
NAV page) allows you to create a three-dimensional
profile which guides you from your present position
and altitude to a final (target) altitude at a specified
location. This is helpful when you’d like to descend
to a certain altitude near an airport. Once the profile
is defined, message alerts and additional data on the
default NAV and map pages will keep you informed of
your progress.
Altitude Reference
(AGL or MSL)
• 3D Navigation — Target Reference
The GPS receiver is in 3D navigation mode and Vertical Speed
computes altitude using satellite data. Required
56 190-00356-00 Rev B
2 - NAV PAGES
Vertical Navigation - VNAV
190-00356-00 Rev B 57
2 - NAV PAGES
Vertical Navigation - VNAV
58 190-00356-00 Rev B
2 - NAV PAGES
Dead Reckoning
Blank Page
60 190-00356-00 Rev B
3 - DIRECT-TO
Selecting a Destination
190-00356-00 Rev B 61
3 - DIRECT-TO
Selecting a Destination
Selecting a Destination by Facility Name or 4. Continue turning the small right knob to
City scroll through any additional database listings
In addition to selecting a destination by identi- for the selected facility name or city. You can
fier, the select direct-to waypoint page also allows you also scroll backwards with the small right
to select airports, VORs and NDBs by facility name or knob if you scroll past the desired waypoint.
city location. If duplicate entries exist for the entered 5. Press ENT to confirm the selected waypoint,
facility name or city, additional entries may be viewed and ENT to activate the direct-to function.
by continuing to turn the small right knob during the
selection process.
Identifier, Symbol Flight Plan
and Region Field
Facility
Name To select the direct-to destination by facility
City name (shown above) or city location (shown
below), highlight the second or third line on
Nearest the direct-to waypoint page. Use the small and
Airport large right knobs to enter the facility name or
Field city. The identifier(s) for any matching entries
will appear on the top line of the page.
To select a direct-to destination by facility name
or city:
1. Press the direct-to key. The select direct-to
waypoint page will appear, with the waypoint
identifier field highlighted.
2. Turn the large right knob to highlight the
facility name (second line; see above) or the
city (third line; see above) field.
3. Use the small and large right knobs to enter
the facility name or city location of the desired
destination waypoint. As you spell the facility
name or city, the 400W-series Spell’N’Find
feature will select the first entry in the database
based upon the characters you have entered
up to that point.
62 190-00356-00 Rev B
3 - DIRECT-TO
Selecting a Destination
Selecting a Destination from the Active Flight Selecting the Nearest Airport as a Direct-To
Plan Destination
If you’re navigating an active flight plan, any The select direct-to waypoint page always displays
waypoint contained in the flight plan may be selected the nearest airports (from your present position) on
as a direct-to destination from the select direct-to the NRST field. Navigating directly to a nearby airport
waypoint page. (see Section 4 - Flight Plans, for more is always just a few simple steps away. (Nearby airports
information on flight plans.) may also be selected as direct-to destinations using the
To select a direct-to destination from the active steps described Section 7 - NRST Pages - Navigating to
flight plan: a Nearby Waypoint.)
1. Press the direct-to key. The select direct-to To select a nearby airport as a direct-to destina-
waypoint page will appear, with the waypoint tion:
identifier field highlighted. 1. Press the direct-to key. The select direct-to
2. Turn the large right knob to highlight the waypoint page will appear, with the waypoint
flight plan (FPL) field. identifier field highlighted.
2. Turn the large right knob to highlight the
nearest airport (NRST) field.
3. Turn the small right knob to display a window
showing up to nine nearby airports.
190-00356-00 Rev B 63
3 - DIRECT-TO
Direct-to Shortcuts
64 190-00356-00 Rev B
3 - DIRECT-TO
Cancelling / Manual Course
190-00356-00 Rev B 65
3 - DIRECT-TO
66 190-00356-00 Rev B
4 - FLIGHT PLANS
Flight Plan Catalog
5. With “Yes” highlighted, press ENT to remove Flight Plan Catalog Options
the waypoint. The following options are available for the Flight
6. Once all changes have been made, press the Plan Catalog:
small right knob to return to the flight plan • Activate Flight Plan
catalog. • Invert and Activate Flight Plan
A one-line user comment may be added to any • Create New Flight Plan
flight plan, which will be displayed on the flight plan • Crossfill
catalog, next to the flight plan’s number. By default, as • Copy Flight Plan
• Delete Flight Plan
the flight plan is being created, the comment will show
• Delete All Flight Plans
the first and last waypoints in the flight plan.
• Sort List by Number/Comment
To change the comment line for an existing flight
plan: Activating Flight Plans
1. From the flight plan catalog, press the small Activate Flight Plan? allows you to select the
right knob to activate the cursor. flight plan for navigation guidance. Once a flight plan
is defined through the Flight Plan Catalog, it may be
2. Turn the large right knob to highlight the
activated for navigation. Activating the flight plan
desired flight plan and press ENT.
places it into “flight plan 00” and overwrites any previ-
3. Turn the large right knob to select the com- ous information at that location.
ment line at the top of the screen.
To activate an existing flight plan:
4. Use the small and large right knobs to enter 1. From the flight plan catalog, press the small
the new comment. Press ENT when finished. right knob to activate the cursor.
2. Turn the large right knob to highlight the
desired flight plan and press MENU to display
the flight plan catalog options.
3. Turn the large right knob to highlight “Acti-
vate Flight Plan?” and press ENT.
68 190-00356-00 Rev B
4 - FLIGHT PLANS
Flight Plan Catalog Options
190-00356-00 Rev B 69
4 - FLIGHT PLANS
Flight Plan Catalog Options
190-00356-00 Rev B 71
4 - FLIGHT PLANS
Flight Plan Catalog Options
72 190-00356-00 Rev B
4 - FLIGHT PLANS
Active Flight Plan
5. Press the small right knob to remove the the desired destination waypoint.
cursor. 2. Select the “Activate Leg?” option from the
To restore factory default settings for data fields active flight plan page options and press
on the active flight plan page: ENT.
1. With the active flight plan page displayed, press
MENU to display the active flight plan page
options window.
2. Turn the large right knob to highlight
“Restore Defaults?” and press ENT.
Active Flight Plan Options
The following options (some covered on the pre- 3. A confirmation window will appear. With
ceding pages) are available for the active flight plan: “Activate?” highlighted, press ENT.
• Activate Leg
Crossfill
• Crossfill
• Copy Flight Plan Crossfill? allows you to transfer the active flight
• Invert Flight Plan plan between two 400W- or 500W-series Garmin units
• Delete Flight Plan in a dual unit installation. See the description on a
• Select Approach previous page in the Flight Plan section.
• Select Arrival Copy Flight Plan
• Select Departure
• Remove Approach Copy Flight Plan? copies the active flight plan
• Remove Arrival to a flight plan catalog location. The copy function
• Remove Departure is useful for duplicating the active flight plan before
• Closest Point of Flight Plan making changes. This feature is described earlier in
• Parallel Track this section.
• Change Fields Invert Flight Plan
• Restore Defaults
I nvert Flight Plan? reverses the active flight plan.
Activate Leg This feature is described earlier in this section.
Activate Leg? activates/reactivates the flight plan 1. With the Active Flight Plan Page displayed,
and selects the highlighted leg as the “active leg” (the press MENU to display the Active Flight Plan
leg which will currently be used for navigation guid- Page Options window.
ance). 2. Turn the large right knob to highlight “Invert
To activate a flight plan along a specific leg: Flight Plan?” and press ENT.
1. Press the small right knob to activate the
cursor and turn the large right knob to highlight
190-00356-00 Rev B 73
4 - FLIGHT PLANS
Active Flight Plan Options
ing the original flight plan until cleared for the 3. A second window will appear listing available
approach—but, keeps the approach available runways for the transition. Turn the small
for quick activation when needed. right knob to highlight the desired runway
5. For approaches not approved for GPS, a and press ENT.
reminder window will appear indicating that
GPS guidance on such approaches is strictly
for monitoring only. To confirm this reminder,
highlight “Yes?” and press ENT.
Select Arrival
Select Arrival? allows you to select a published
standard terminal arrival route (STAR) for the destina- 4. With “Load?” highlighted, press ENT.
tion airport, or replace the current arrival with a new Select Departure
selection.
Select Departure? allows you to select a pub-
To select an arrival for a direct-to or flight plan lished standard instrument departure (SID) for the
destination airport:
departure airport, or replace the current departure
1. Select the “Select Arrival?” option from the with a new selection. When using a direct-to, the
active flight plan page options and press 400W-series will use the nearest airport as a reference
ENT. when displaying available departures. See Sec 5 - Pro-
cedures for information on selecting departures using
the PROC key.
To select a departure for the departure airport:
1. Select the “Select Departure?” option from
the active flight plan page options and press
ENT.
2. A window will appear listing the available 2. A window will appear listing the available
transitions for your destination airport. Turn departures for your departure airport. Turn
the small right knob to highlight the desired the small right knob to select the desired
transition waypoint and press ENT. departure and press ENT.
3. A second window will appear listing available
transitions for the departure. Turn the small
right knob to highlight the desired transition
waypoint and press ENT.
4. With “Load?” highlighted, press ENT.
190-00356-00 Rev B 75
4 - FLIGHT PLANS
Active Flight Plan Options
Remove Approach, Arrival, or Departure To determine the closest point, along the active
Remove Approach? deletes the currently selected flight plan, to a selected waypoint:
approach from the active flight plan. Remove Arrival? 1. Select the “Closest Point of FPL?” option from
deletes the current Arrival (STAR) from the active the active flight plan page options and press
flight plan. Remove Departure? deletes the current ENT.
departure (SID) from the active flight plan.
To remove an approach, arrival or departure from
the active flight plan:
1. Press MENU and turn the large right knob
to select the “Remove Approach?”, “Remove
Arrival?” or “Remove Departure?” option from
the active flight plan page options and press 2. A window will appear with the reference
ENT. waypoint field highlighted. Use the small and
large right knobs to enter the identifier of the
reference waypoint and press ENT.
3. A confirmation window will appear for the
selected reference waypoint. Press ENT to
accept the waypoint.
4. The 400W-series will display the bearing (BRG)
2. A confirmation window will appear listing and distance (DIST) to the closest point along
the procedure you are about to remove. With the flight plan, from the selected reference
“Yes?” highlighted, press ENT. waypoint. To create a user waypoint at this
location and add it to the flight plan, highlight
“Load?” and press ENT. The name for the new
user waypoint will be derived from the identi-
fier of the reference waypoint.
76 190-00356-00 Rev B
4 - FLIGHT PLANS
Active Flight Plan Options
FROM
WPT
This same process may also be used to remove 2. Press direct-to twice to display an “Activate
individual waypoints from the active flight plan. Leg” confirmation window.
To remove a waypoint using the CLR key:
1. With the active flight plan page displayed, press
the small right knob to activate the cursor.
2. Turn the large right knob to highlight the
identifier for the waypoint you wish to delete.
Identifiers will appear in green text.
3. Press CLR to display a confirmation window. 3. With “Activate?” highlighted, press ENT.
When using instrument procedures, this feature
can be used not only to activate a specific point-to-
point leg, but to also activate the procedure turn
portion of an approach, follow a DME arc or activate a
holding pattern.
Any approach, departure or arrival can be reviewed
4. With “Yes?” highlighted, press ENT to remove on the appropriate airport page in the Waypoint page
the selected procedure. group.
The “Activate Leg?” provides a shortcut that allows To review a procedure while viewing a flight plan
page:
you to specify which leg of the flight plan will cur-
rently be used for navigation guidance, using the 1. With a flight plan page displayed, press the
direct-to key. small right knob to activate the cursor.
To activate a specific leg of the active flight plan: 2. Turn the large right knob to highlight the
procedure header and press ENT to select the
1. Press the small right knob to activate the
WPT page group.
cursor and turn the large right knob to high-
light the desired destination waypoint.
190-00356-00 Rev B 79
4 - FLIGHT PLANS
Active Flight Plan Shortcuts
Blank Page
80 190-00356-00 Rev B
5 - PROCEDURES
Approaches/Departures/Arrivals
Section 5
Approaches, Departures, & Arrivals
The 400W-series unit allows you to fly non-preci-
sion and precision approaches to airports with pub-
lished instrument approach procedures. All available
approaches are stored on your Jeppesen NavData® card,
and are automatically updated when you replace the 4. A second window will appear listing the avail-
card with a new one. Subscription information for Nav- able transitions. Turn the large right knob to
Data cards is included in your 400W-series package. highlight the desired transition waypoint and
press ENT. (The approach “Vectors” option
The Procedures Page is displayed by pressing the
assumes you will receive vectors to the final
PROC key. The Procedures Page provides direct access
course segment of the approach and will pro-
to approaches, departures and arrivals — based upon vide navigation guidance relative to the final
the active flight plan or direct-to destination. In either approach course.)
case, the departure and destination airports must have
published procedures associated with them.
To select an approach, departure or arrival:
1. Press the PROC key to display the procedures page.
Not all approaches in the database To activate the approach, with vectors to final:
are approved for GPS use. As you 1. Press the PROC key to display the procedures
select an approach, a “GPS” designa- page.
tion to the right of the procedure 2. Turn the large right knob to highlight “Acti-
name indicates the procedure can be flown using vate Vector-To-Final?” and press ENT.
the GPS receiver. Some procedures will not have
this designation, meaning the GPS receiver may be
used for supplemental navigation guidance only. ILS
approaches, for example, must be flown by tuning the
VLOC receiver to the proper frequency and coupling
the VLOC receiver to the external CDI (or HSI).
Once an approach is selected, it may be activated
for navigation from the procedures page. Activating the In many cases, it may be easiest to “Load” the full
approach overrides the “en route” portion of the active approach while still some distance away, en route to
flight plan, proceeding directly to the “approach” the destination airport. Later, if vectored to final, use
portion (for a full approach, directly to the initial the steps above to select “Activate Vectors-To-Final”—
approach fix). Activating the approach also initiates which makes the inbound course to the FAF waypoint
automatic CDI scaling transition as the approach active. Otherwise, activate the full approach using the
progresses. ”Activate Approach?” option.
To activate an approach: If you reactivate the approach currently being
1. Press the PROC key to display the procedures flown using the PROC key, prior to reaching the MAP
page. a Restart Approach confirmation window appears on
2. Turn the large right knob to highlight “Acti- the screen. If you have passed the MAP, the 400W-
vate Approach?” and press ENT. series unit proceeds to the transition waypoint without
a restart confirmation.
190-00356-00 Rev B 83
5 - PROCEDURES
Procedure Turn Approach
LYH VOR (the IAF). Also, select “Load?” to load Flying the Procedure Turn
(but not activate) the approach. 1. Within 31 nautical miles of the destination
airport, the 400W-series will switch from “en
route” mode to “terminal” mode (as indicated
in the lower left corner of the screen). The
switch to terminal mode is accompanied by a
gradual Course Deviation Indicator (CDI) scale
transition from 2.0 to 1.0 nautical miles, full
scale deflection. (See example below)
[RW04]
DO NOT USE FOR
NAVIGATION
190-00356-00 Rev B 85
5 - PROCEDURES
Procedure Turn Approach
4. Fly the outbound course, keeping the CDI
needle centered.
5. Once you have flown approximately one minute
past the FAF (LYH), the alert message “LT TO
160° x S” will appear in the lower right corner
of the screen. You may initiate the procedure DO NOT USE FOR
turn at any time after receiving this alert mes- NAVIGATION
sage.
86 190-00356-00 Rev B
5 - PROCEDURES
Procedure Turn Approach
pended at the MAP. A “from” indication will The OBS key is used to initiate the missed approach,
be displayed on the CDI and default NAV page, as follows:
but course guidance along the final approach 1. Press the OBS key after the SUSP annunciator
course will continue. If a missed approach is appears. If you press the OBS key a second
required, use the OBS key to initiate the missed time, the missed approach holding point
approach sequence. (MAHP; in this case “SWARM” intersection)
is automatically offered as the destination
waypoint.
DO NOT USE FOR
4. The 400W-series unit will provide course guid- NAVIGATION
ance only on the inbound side of the holding
pattern. When leaving the holding pattern
to re-fly the approach (or another approach) 3. Press ENT twice.
press the PROC key to “Select Approach?” or This time, you select the GPS runway 21 approach
“Activate Approach?” as previously described. into Farmville Regional. The GPS runway 21 approach
(Or, use the direct-to key to select another begins with a holding pattern at the IAF, BODRY
destination.) intersection.
Flying an Approach with a Hold 4. Press PROC and select the “GPS 21”
approach.
Starting where the previous example left off,
we’ll assume weather conditions resulted in a missed
approach at Lynchburg Regional. Now, you’ve decided
to divert to Farmville Regional (KFVX) instead.
1. Press direct-to.
2. Use the small and large right knobs to enter
the destination airport’s identifier (KFVX).
5. From the transitions window, select BODRY
intersection as the IAF. Also, select “Activate?”
to load and activate the approach.
190-00356-00 Rev B 89
5 - PROCEDURES
Approach with Hold
6. Once you activate the approach, the active 9. As mentioned in the missed approach example,
flight plan page will appear. You may review the default NAV page will display a timer
the approach sequence by pressing the small during the holding pattern. Use this timer to fly
right knob and turning the large right knob. the one minute outbound portion of the hold-
Press FPL to return to the navigation pages. ing pattern. (The holding pattern is displayed
on the map page and indicated as the active
leg on the default NAV and active flight plan
pages.)
7. As in the last example, within 31 nautical miles
of the airport, the 400W-series unit will switch
from en route mode to terminal mode, and the
CDI scale will transition from 2.0 to 1.0 nautical
miles, full scale deflection.
31nm (from airport)
NOTE: Upon activating an RNAV GPS approach,
you are given the option to skip any non-required
holding patterns during the initial transitions of DO NOT USE FOR
the approach. In a GPS approach, you will not be NAVIGATION
given the option and you must manually reselect
waypoint sequencing.
8. Just prior to crossing BODRY intersection, an
alert—”HOLD TEARDROP”—will appear in
the lower right corner of the screen to sug-
gest the proper holding pattern entry. (“HOLD
DIRECT” or “HOLD PARALLEL” may be offered
on other similar approaches.)
90 190-00356-00 Rev B
5 - PROCEDURES
Approach with Hold
190-00356-00 Rev B 91
5 - PROCEDURES
DME Arc Approach
16. As you cross the MAP, “SUSP” will appear Flying a DME Arc Approach
above the OBS key, indicating that automatic The GPS overlay for a DME arc approach uses
sequencing of approach waypoints will be sus- additional Jeppesen-provided waypoints to define the
pended at the MAP. A “from” indication will arc. These waypoints are indicated by “D” as the first
be displayed on the CDI and default NAV page, letter in the waypoint name. This is followed by three
but course guidance along the final approach numbers which indicate the radial the waypoint lies
course will continue. If a missed approach is on. The last letter indicates the radius of the arc.
required, use the OBS key to initiate the missed
Billard Muni (Topeka, KS)
approach sequence.
VOR or GPS Rwy 22
DO NOT USE
FOR NAVIGATION
2. Press the PROC key and select the “VOR 22”
approach. From the transitions window, select 31 nm (from airport)
“LEBVY” as the IAF. Also, select “Load?” (or Billard Muni (Topeka, KS)
“Activate?”, if already cleared direct to the IAF VOR Rwy 22
for the approach).
4. If you haven’t already activated the approach
(in step #2 above), be sure to do so when
cleared for the approach.
190-00356-00 Rev B 93
5 - PROCEDURES
DME Arc Approach
190-00356-00 Rev B 95
5 - PROCEDURES
Vectors-To-Final Approach
1.
When VTF is activated, the 500W-series unit
switches from en route mode to terminal mode
and the CDI scale transitions from 2.0 to 1.0
nautical miles, full scale deflection.
2. If you haven’t already done so, activate the
approach (with vectors-to-final). This allows
the 400W-series unit to guide you to the final
96 190-00356-00 Rev B
5 - PROCEDURES
Vectors-To-Final Approach
approach course.
3. ATC instructs you to turn left to a heading 6. As the CDI needle centers, make any remain-
of 025°. This places you parallel to the final ing course corrections to establish yourself on
approach course in the opposite direction. CDI the final approach course. Vectors-To-Final
needle deflection is to the left. activates the approach immediately and gives
a 2° angular full scale deflection all the way
to and beyond the FAF (up to 1 NM full-scale
deflection).
4. ATC instructs you to turn right to a heading of
115°.
190-00356-00 Rev B 97
5 - PROCEDURES
Course-From-Fix Legs
190-00356-00 Rev B 99
5 - PROCEDURES
Course-From-Fix Legs
DO NOT USE FOR NAVIGATION
MISSED APPROACH
COASTAL ONE DEPARTURE
(CSTL1.CCC)
DEPARTING BARNES MUNI,
Fly assigned heading and altitude
for radar vectors to HFD
VOR. Expect clearance to
requested flight level 10
minutes after departure. From
over HFD VOR, proceed via the HFD R-143 to
Thumb Int,
then via the HTO R-010 to
6. As you approach PMD VOR (the missed Yoder Int, then via the CCC
The automatic switch from GPS to VLOC is not Selecting an ILS Approach
immediate, but instead occurs gradually to prevent For this example, we’ll use a flight from Laughlin
abrupt CDI changes when coupled to an autopilot. Bullhead (Arizona) International to Flagstaff Pul-
The CDI selection can also be changed manually by liam (KFLG) and select the ILS runway 21 approach.
pressing the CDI key. Once the switch from GPS to “SHUTR” intersection will be selected as the IAF,
VLOC has occurred, either automatically or manu- which will include an outbound leg and a procedure
ally, it will not automatically switch again until the
turn. Of course, vectors-to-final could also be selected,
approach is reactivated or another approach is
as previously described for the non-precision approach
selected. To prevent automatic ILS CDI selection,
examples.
choose the “Manual” ILS CDI setting. (The factory
default setting is “Auto”, which enables the automatic 1. Select Flagstaff Pulliam (KFLG) as your des-
switch to VLOC.) tination, via the direct-to key or as the last
waypoint in a flight plan.
1.2NM 1.2NM
15NM
GPS
VLOC
witch
Auto S
to V L OC
......
in th is area..
wit h
2. Press the PROC key and select the “ILS 21”
VLOC
GPS
approach.
2NM
MANUAL
FAF
DO NOT USE FOR
NAVIGATION
DO NOT USE FOR
NAVIGATION
page. With “Load?” highlighted press ENT to 3. As the distance (DIST) to the IAF approaches
load the approach into the flight plan. zero, the message is replaced by a turn advisory
that counts down 10 seconds prior to the turn.
4. As you approach the FAF (LOTKE), the 400W
Series unit will begin to automatically rescale
in an angular fashion. This will allow the LPV
approach to be flown in an identical fashion
to a standard ILS. At 2.0 NM from the FAF, CDI
scaling is tightened from 1.0 to the angular full
4. After the approach is loaded into the flight scale deflection (typically the angular full-scale
plan, you can view the approach waypoints. deflection is 2.0°, but will be as defined for the
approach.
navigation to the missed approach when the 8. When viewing the Map Page, you’ll note
message is acknowledged. that the final course segment is displayed
6. Capture the glideslope as you would an ILS in magenta (the active leg of the flight plan
glideslope. always appears in magenta).
7. As you cross LOTKE, the destination sequences 9. As you approach the MAP, a waypoint message
to the MAP (“RW31”, the runway threshold). (“DTK 312° x S”) appears on the bottom of
With the needle on the external CDI (or HSI) the screen.
centered, fly toward the MAP, observing the 10. Once the unit crosses the MAP (defined as
altitude minimums dictated by the approach the runway end waypoint), sequencing will
plate. be suspended. Prepare the aircraft for missed
approach operation. Press the OBS key to
sequence to the Missed Approach procedure.
11. Fly the guidance provided by the unit to the
ARTTY intersection and hold.
Points to Remember for All Approaches Points to Remember for Localizer or VOR-
• The GNS 400W-series unit is designed to comple- based Approaches
ment your printed approach plates and vastly • The default factory setting allows the CDI output to
improve situational awareness throughout the automatically switch from the GPS receiver to the
approach. However, you must always fly an approach LOC receiver. This may be changed to manual in
as it appears on the approach plate. some installations. If the “ILS CDI Selection” setting
• The active leg (or the portion of the approach is changed to “Manual”, you must determine when
currently in use) is depicted in magenta on the to select “GPS” or “VLOC” guidance during the
Map Page. As you fly the approach, the 400W- approach. Remember, “VLOC” is required for the
series unit automatically sequences through each final course segment from Final Approach Fix (FAF)
leg of the approach unless “SUSP” appears above to MAP.
the OBS key. “SUSP” indicates that automatic
sequencing of approach waypoints is suspended on
the current leg and normally appears at holding
patterns and upon crossing the missed approach
point (MAP).
Airport Location Airport Runway Airport Frequency Airport Approach Airport Arrival Airport Departure
NOTE: Please note that your 400W-series uses ICAO identifiers for all airports. All U.S. airport identifiers which
contain only letters use the prefix “K”. For example, Los Angeles International is KLAX under the ICAO standard.
Other airports, such as Otten Memorial (3VS), that contain numbers in the identifier, do not require the “K” prefix.
Many foreign countries use two letter prefixes.
The WPT page group includes ten pages. While To enter a waypoint facility name or city location:
viewing any WPT page, turn the small right knob 1. Select the airport location page, NDB page or
to select a different WPT page. The first six pages VOR page from the WPT page group.
provide detailed information for the selected airport: 2. Press the small right knob to activate the
location, runways, frequencies, approaches, arrivals, cursor.
and departures. The last four pages provide informa-
tion for intersections, NDBs, VORs and user-created 3. Turn the large right knob to select the facility
name or location (city) field.
waypoints.
4. Turn the small right knob to select the desired
After a WPT page is selected, information for a
character.
waypoint may be viewed by entering the identifier (or
name) of the desired waypoint. Airports, NDBs and
VORs may be selected by identifier, facility name or
location (city).
To enter a waypoint identifier:
1. Select the desired WPT page and press the
small right knob to activate the cursor.
5. Turn the large right knob to select the next
2. Turn the small right knob to select the first
character field.
character of the waypoint’s identifier.
6. Repeat steps 4 and 5 until the facility name or
3. Turn the large right knob to select the next
location is selected, then press ENT.
character field.
4. Turn the small right knob to select the desired
character.
5. Repeat steps 3 and 4 until the identifier is
selected, then press ENT.
6. To remove the flashing cursor, press the small
right knob.
7. To remove the flashing cursor, press the small
right knob.
Duplicate Waypoints
Once the identifier, facility name or location is
entered, all six airport pages will display informa-
tion for the selected airport. As you enter an iden-
tifier, facility name or location, the 400W-series
Spell’N’Find™ feature will scroll through the database,
displaying those waypoints matching the characters 4. Press ENT to select the desired facility name
you have entered to that point. If duplicate entries or location.
exist for the entered facility name or location, addi-
5. To remove the flashing cursor, press the small
tional entries may be viewed by continuing to turn
right knob.
the small right knob during the selection process.
If duplicate entries exist for an entered identifier, a To select a waypoint identifier from a list of
duplicates:
duplicate waypoint page will appear once you select the
identifier (by pressing ENT). 1. Select the desired airport or navaid identifier.
To select a facility name or location, where dupli- 2. A duplicate waypoints window will appear.
cate entries exist: Turn the large right knob to select the desired
1. Select the desired facility name or location. waypoint and press ENT.
2. As you spell the facility name or location,
using the small and large right knobs, the
400W-series Spell’N’Find feature will select
the first entry in the database based upon the
characters you have entered up to that point.
Map Image
Runway Surface
and Lighting
Second Page
6. To remove the flashing cursor, press the small
in WPT group right knob.
Runway Length
and Width To adjust the scale of the map image:
To display information for each additional 1. Press the down arrow side of the RNG key to
runway: display a smaller map area.
1. Press the small right knob to activate the 2. Press the up arrow side of the RNG key to
cursor. display a larger map area.
2. Turn the large right knob to place the cursor
on the runway designation field.
4. To remove the flashing cursor, press the small The following descriptions and abbreviations are
right knob. used on the airport frequency page:
Some listed frequencies may include designations • Type— Usage type: Public, Military,
for limited usage, as follows: Heliport, or Private
“TX” - transmit only • Frequency— Communication frequencies
“RX” - receive only which may include restric-
“PT” - part time frequency tions:
If a listed frequency has sector or altitude restric- Approach Arrival Class B
tions, the frequency will be preceded by an “Info?” Class C CTA Departure
designation.
TMA Terminal TRSA
To view usage restrictions for a frequency:
Communication frequencies without restrictions:
1. Turn the large right knob to place the cursor
on the “Info?” designation directly to the left ATIS ASOS AWOS
of the desired frequency. Center Clearance Gate
Control Ground Helicopter
Multicom Pre-taxi Radar
Ramp Other Tower
Unicom
Navigation frequencies:
2. Press ENT to display the restriction informa-
ILS LOC
tion.
Airport Frequency Page Options 2. Turn the large right knob to place the cursor
on the approach (APR) procedure name field.
Select Next FPL Apt?
As described earlier in this section.
Select Destination Apt?
As described earlier in this section.
Airport Approach Page
WAAS Identifier, Symbol Approach
approach and Type Procedure Name 3. Turn the small right knob to display a window
ID of available approaches for the selected airport.
Continue turning the small right knob to
select the desired approach.
Transitions: IAFs,
Feeder Routes and
Vectors-to-Final
Fourth Page in
Map Image WPT Group
4. Press ENT. The cursor moves to the transitions
(TRANS) field.
The airport approach page shows the available
approach procedures for the selected airport. Where 5. Turn the small right knob to display a window
multiple initial approach fixes (IAFs) and feeder routes of available transitions. Continue turning
are available, that information may also be displayed. the small right knob to select the desired
transition or select “VECTORS” for guidance
A map image provides a layout diagram for each
only along the final course segment of the
approach and transition.
approach.
If a WAAS approach has been selected, the WAAS
approach ID is displayed in the top left corner of the
map. The approach service level is shown in the lower
right corner of the map. Service level annunciations
available are: LPV, L/VNAV, LNAV+V, or LNAV.
To scroll through the available approaches and
transitions:
6. Press ENT. To remove the flashing cursor, press
1. Press the small right knob to activate the
the small right knob.
cursor.
After selecting the Approach Channel, the WAAS Airport Arrival Page
approach ID will be shown in the top left corner of The airport arrival page shows the available Airport
the map display. Standard Terminal Arrival (STAR) procedures for
To select an approach channel from the Airport the selected airport. Where multiple transitions or
Approach Page: runways are associated with the arrival procedure,
1. Press MENU to display the Airport Approach that information may also be displayed. A map image
Page Options. provides a layout diagram for each arrival, transition
2. Turn the small or large right knob to highlight and runway.
“Select Approach Chnl? and then press ENT. Airport Identifier, Map Image
Symbol and Type
3. Turn the small right knob to change values
Arrival
and the large right knob to move the cursor. Procedure Name
After selecting the WAAS approach channel,
press ENT. Transitions
4. Select the desired transition and press ENT. Runways Associated
with Arrival
S elect Next FPL Apt?
As described earlier in this section.
Fifth Page
Select Destination Apt? in WPT group
As described earlier in this section.
To scroll through the available arrivals:
1. Press the small right knob to activate the
cursor.
2. Turn the large right knob to place the cursor
on the arrival procedure name field.
2. Turn the large right knob to place the cursor 6. Press ENT. The cursor moves to the transitions
on the departure (DEP) procedure name field. (TRANS) field.
7. Turn the small right knob to display a window
of available transitions. Continue turning the
small right knob to select the desired transi-
tion.
8. Press ENT. To remove the flashing cursor, press
the small right knob.
3. Turn the small right knob to display a window Airport Departure Page Options
of available departures for the selected airport. The following options are available for the airport
Continue turning the small right knob to
departure page, by pressing the MENU key:
select the desired departure.
Latitude/Longitude
Eighth Page
Position
Latitude/Longitude in WPT group
Seventh Page Position
in WPT group
The following descriptions and abbreviations are
The following descriptions and abbreviations are used:
used:
• Symbol— See Section 2 Nav Pages - Map Page
• Position— Latitude/Longitude (degrees/minutes for a graphic illustration of available
or degrees/minutes/seconds), MGRS NDB symbols
or UTM/UPS
• Position— Latitude/Longitude
• RAD— Radial from nearest VOR in degrees (degrees/minutes or degrees/
magnetic or degrees true (depending minutes/seconds), MGRS or
upon unit configuration) UTM/UPS
• DIS— Distance from nearest VOR, in nauti- • FREQ— Frequency in kilohertz (kHz)
cal miles/statute miles/kilometers
• Wx Brdcst— Weather information is
(depending upon unit configuration)
broadcast on the selected
NOTE: The VOR displayed on the intersection facility’s frequency
page is the nearest VOR, not necessarily the VOR
used to define the intersection.
5. Press ENT to accept the selected position. 6. The cursor moves to the distance (DIS) field.
6. The cursor moves to “Create?”. Press ENT to Use the small and large right knobs to enter
add the new waypoint to memory. the distance from the reference waypoint to the
new user waypoint. Press ENT to accept the
7. Press the small right knob to remove the
selected distance.
flashing cursor.
7. Turn the large right knob to highlight
To create a new user waypoint by referencing an
existing waypoint:
“Create?” and press ENT.
1. With the user waypoint page displayed, press
the small right knob to activate the cursor.
2. Use the small and large right knobs to
enter a name for the new waypoint and press
ENT.
3. Turn the large right knob to highlight the first
reference waypoint (REF WPT) field. 8. Press the small right knob to remove the
flashing cursor.
4. Use the small and large right knobs to enter
the identifier of the reference waypoint. The NOTE: The 400W-series units allow you to create
a new user waypoint at a defined radial and
reference waypoint can be an airport, VOR, distance from your present position. To reference
NDB, intersection or another user waypoint. your present position, follow the steps above, but
Press ENT to accept the selected identifier. press CLR in step #4. “P.POS” will appear in the
5. The cursor moves to the radial (RAD) field. Use reference waypoint (REF WPT) field to indicate
that radial and distance information will refer-
the small and large right knobs to enter
ence your present position.
the radial from the reference waypoint to the
new user waypoint. Press ENT to accept the The second reference waypoint field (REF WPT) is
selected radial. a temporary reference only—not a reference that
will be stored with the user waypoint. By default,
this field will display a radial from the nearest
VOR. However, you can select any waypoint—by
identifier—to use as a reference in this field.
Your 400W-series unit can store user-defined
128 190-00356-00 Rev B
6 - WPT PAGES
Creating User Waypoints
waypoints which are generated from other 4. The cursor moves to the “Create?” action field.
equipment in your panel. For example, an EFIS Press ENT to save the new waypoint.
equipped with joystick inputs can be used to
create user waypoints which will (if your installa- Modifying User Waypoints
tion supports this) automatically transfer to your To modify an existing waypoint, select that
400W-series unit. waypoint on the user waypoint page and enter the new
position information directly over the old information.
Creating User Waypoints from the Map Page
The map page and panning target pointer provide a To modify a user waypoint by changing its lati-
tude/longitude position:
quick means of saving your present position as a user-
defined waypoint. 1. With the user waypoint page displayed, press
the small right knob to activate the cursor.
To capture and save your present position as a
user waypoint: 2. Use the small and large right knobs to enter
1. With the map page displayed, press the small the name of the desired waypoint and press
right knob to activate the panning function. ENT.
The target pointer will appear at your present 3. Turn the large right knob to highlight the
position. position field at the bottom of the page.
4. Use the small and large right knobs to enter
the new position coordinates and press ENT
to accept the selected position.
3. The top of the user waypoint list will indicate User Waypoint List
the total number of user waypoints currently The user waypoint list allows you to review,
used and available memory. If more user modify, rename or delete a selected user waypoint,
waypoints are stored than can be displayed or to delete all user waypoints currently stored in
on a single screen, turn the large right knob memory. The top of the page shows the number of
to scroll through the user waypoint list. waypoints used and available memory.
4. Press the small right knob to return to the To review and/or modify a user waypoint from the
user waypoint page. user waypoint list:
Delete User Waypoint? allows you to delete the 1. Select the user waypoint list, as described in
selected waypoint from memory. the User Waypoint Options.
To delete a user waypoint:
2. Turn the large right knob to highlight the
1. Select the desired waypoint on the user desired user waypoint.
waypoint page and press MENU to display
the user waypoint page options. 3. Press ENT to display the user waypoint page for
the selected waypoint. From this page you may
2. Turn the large right knob to highlight “Delete review all information defining the waypoint
User Waypoint?” and press ENT. and its position.
4. To modify the waypoint’s position or refer-
ence waypoint information, follow the steps
described “Modifying User Waypoints.” (Keep
in mind that you’ve already selected a user
waypoint page which displays the desired user
waypoint, so you may skip the first two steps
Crossfill? allows you to transfer a user waypoint of the procedure.)
to another 400W/500W series unit (if installed). 5. To exit the user waypoint page, turn the large
right knob to highlight “Done?” and press
ENT.
To rename a user waypoint from the user To delete a user waypoint from the user waypoint
waypoint list: list:
1. Select the user waypoint list. 1. Select the user waypoint list.
2. Turn the large right knob to highlight the 2. Turn the large right knob to highlight the
desired user waypoint. desired user waypoint.
3. Use the small and large right knobs to 3. Press CLR to display a “delete waypoint”
change the name of the user waypoint. (Enter confirmation window.
the new name directly over the old name.)
Press ENT to accept the new name.
Nearest Airport Nearest Intersection Nearest NDB Nearest VOR Nearest User Nearest Center
Not all 25 nearest airports, VORs, NDBs, inter- To scroll through the list of nearest flight service
sections or user waypoints can be displayed on the station or center points of communication:
corresponding NRST page at one time. The nearest 1. Select the desired NRST page.
airport page displays detailed information for three 2. Press the small right knob to activate the
nearest airports, with a scroll bar along the right-hand cursor.
side of the page indicating which part of the list is cur- 3. Turn the small right knob to scroll through
rently being viewed. The nearest airspace page displays the list.
detailed information for up to three special use or
controlled airspace alerts. The NRST pages for VORs,
NDBs, intersections, and user waypoints will display
five waypoints at a time. The flashing cursor and large
right knob are used to scroll and view the rest of the
waypoints or airspaces in the list.
To scroll through the list of nearest airports, VORs,
NDBs, intersections, user waypoints or SUAs:
1. Select the desired NRST page.
2. Press the small right knob to activate the
cursor.
3. Turn the large right knob to scroll through the
list. The scroll bar along the right-hand side of
the page will indicate which part of the list is 4. Press the small right knob to remove the
currently being viewed. flashing cursor.
Scroll Bar
To quickly tune the common traffic advisory frequency Additional communication frequencies, runway
(CTAF) from the nearest airport page: information and more is available from the nearest
1. Select the nearest airport page. airport page by highlighting the identifier of the desired
2. Press the small right knob to activate the airport and pressing ENT.
cursor. To view additional information for a nearby
3. Turn the large right knob to scroll through the airport:
list, highlighting the COM frequency associated 1. Select the nearest airport page.
with the desired airport. 2. Press the small right knob to activate the
cursor.
3. Turn the large right knob to scroll through
the list, highlighting the identifier of the desired
airport.
4. Press ENT to place the selected frequency in Nearest User Waypoint Page
the standby field of the VLOC window. The nearest user waypoint page displays the name,
bearing and distance to the 25 nearest user waypoints
(within 200 nautical miles of your present position).
Nearest Center (ARTCC) Page
The nearest center page displays the facility name,
bearing to and distance to the five nearest ARTCC
points of communication (within 200 nautical miles
5. Press the VLOC flip-flop key to activate the of your present position). For each ARTCC listed, the
selected frequency. nearest center page also indicates the frequency(s) and
6. Press the small right knob to remove the may be used to quickly tune the COM transceiver to
flashing cursor. the center’s frequency. The selected frequency is placed
To view additional information for a nearby VOR: in the standby field of the COM window and activated
using the COM flip-flop key.
1. Select the nearest VOR page.
ARTCC Name Frequency(s)
2. Press the small right knob to activate the
cursor.
3. Turn the large right knob to scroll through
the list, highlighting the identifier of the desired Bearing To and
VOR. Distance To
To quickly tune an ARTCC’s frequency from the Nearest Flight Service Station (FSS) Page
nearest center page:
The nearest flight service station page displays the
1. Select the nearest center page. facility name, bearing to and distance to the five near-
2. Press the small right knob to activate the est FSS points of communication (within 200 nautical
cursor. miles of your present position). For each FSS listed,
3. Turn the small right knob to scroll through the nearest flight service station page also indicates
the list, selecting the desired ARTCC. the frequency(s) and may be used to quickly tune the
COM transceiver to the FSS’s frequency. The selected
frequency is placed in the standby field of the COM
window and activated using the COM flip-flop key.
FSS Name
Frequency(s)
4. Turn the large right knob to scroll down the
page, highlighting the desired frequency.
VOR Identifier
(for duplex
operation)
Bearing To and Page location
Distance To in NRST group
To quickly tune an FSS’s frequency from the near- Nearest Airspace Page
est flight service station page:
The last page in the NRST group, the nearest air-
1. Select the nearest flight service station page
and press the small right knob to activate the space page, will alert you to as many as nine controlled
cursor. or special use airspaces near or in your flight path.
Alerts are provided according to the following condi-
2. Turn the small right knob to scroll through
tions:
the list, selecting the desired FSS.
• If your projected course will take you inside an
airspace within the next ten minutes, the alert
message “Airspace ahead -- less than 10 min-
utes” will appear. The nearest airspace page will
show the airspace as “Ahead”.
Eighth Page
Airspace Name in NRST group
6. Press the small right knob to remove the 4. Press ENT to place the selected frequency in
flashing cursor. the standby field of the COM window.
To view and quickly tune the frequency for a
controlling agency:
“Done?” Field
(return to
previous page)
“Frequency?”
Field (display
5. Press the COM flip-flop key to activate the
frequency page)
selected frequency.
Airspace Name Status and 6. To return to the airspace page, turn the large
and Type Time to Entry Floor/Ceiling Limits right knob to highlight “Done?” and press
ENT (or press CLR).
1. Follow steps #1 through #4 on the previous
page to display the airspace page for the 7. To return to the nearest airspace page, turn the
desired controlled or special use airspace. large right knob to highlight “Done?” and
press ENT (or press CLR).
2. Turn the large right knob to highlight “Fre-
quencies?” and press ENT. 8. Press the small right knob to remove the
flashing cursor.
The airspace page displays (and airspace alert mes-
sages are provided for) the following airspace types:
• Alert • Caution
• Class B • Class C
• Class D •C
TA
3. Turn the large right knob to scroll through
the list, highlighting the desired frequency.
• Danger • MOA
• Prohibited • Restricted
• TMA • Training
• TRSA • Unspecified
• Warning
The bottom right-hand corner of the airspace page
displays the floor and ceiling limits of the airspace.
The following are examples of what may appear as
vertical limits for an airspace:
142 190-00356-00 Rev B
7 - NRST PAGES
Nearest Airspaces
Blank Page
6. Press the small right knob to remove the 5. A second window will appear listing available
flashing cursor. transitions. Turn the small right knob to
NOTE: For duplex COM operations, the VLOC re- highlight the desired transition waypoint and
ceiver may be auto-tuned from the nearest flight press ENT. (The approach “Vectors” option
service station page. assumes you will receive vectors to the final
course segment of the approach and will
When selecting a VOR or ILS approach, manual provide navigation guidance to intercept this
tuning of the VLOC receiver is not required. Once final course.)
the approach procedure is “Loaded” or “Acti-
6. Turn the large right knob to highlight “Load?”
vated”, the GNS 430W will automatically place
or “Activate?” and press ENT. (“Load?” will
the proper frequency in the standby field of the
add the procedure to the flight plan without
VLOC window. If you wish to use this frequency,
immediately using it for navigation guidance.
simply press the VLOC flip-flop key to activate
This allows you to continue navigating the
the frequency. Additional information on approach
original flight plan, but keeps the procedure
procedures is provided in Section 5.
available on the active flight plan page for
To select an approach and automatically tune the quick activation when needed.)
proper VLOC frequency:
1. Select the destination airport using the direct-
to key or as the last waypoint in the active
flight plan.
2. Press the PROC key to display the procedures
page.
3. Turn the large right knob to highlight “Select
7. For VOR and ILS approaches, the standby field
Approach?” and press ENT.
of the VLOC window is automatically tuned to
the proper frequency. To activate the frequency
press the VLOC flip-flop key. To display VLOC
course information on the external CDI (or HSI)
press CDI and verify that “VLOC” is displayed
at the bottom left corner of the screen, directly
above the CDI key.
4. A window will appear listing the available pro-
cedures. Turn the small right knob to highlight
the desired procedure and press ENT. (When
a direct-to destination is selected, departures
are offered for the nearest airport.)
CDI Key
The GNS 430W’s CDI key is used to couple the
GPS or VLOC receiver to the external CDI (or HSI).
When the external CDI (or HSI) is being driven by
the GPS receiver, “GPS” will appear at the bottom left
corner of the page, directly above the CDI key. When
the external CDI (or HSI) is being driven by the VLOC
receiver, “VLOC” will appear instead.
To couple the external CDI (or HSI) to the GPS
receiver or VLOC receiver, press the CDI key to
display “GPS” or “VLOC”, as desired.
To select, highlight
with cursor and
press ENT.
Density Alt / TAS / Winds— indicates the theo- the other mode, then press ENT to accept the
retical altitude at which your aircraft will perform other mode.
depending upon several environmental conditions,
including indicated altitude (IND ALT), barometric
setting (BARO) and total air temperature (TAT; the
temperature, including the heating effect of speed,
read on a standard outside temperature gauge).
This computes true airspeed (TAS), based upon the
factors above and the calibrated airspeed (CAS).
Also, this determines winds aloft—the wind direc-
tion and speed—and a head wind/tail wind com-
ponent, based upon the calculated density altitude
(DEN ALT), true airspeed, aircraft heading (HDG)
and ground speed.
Crossfill— allows the pilot to transfer the active
flight plan, any stored flight plan, a user waypoint The “Flight Plan?” option allows you to
or all user waypoints between two 400W-Series select the numbered flight plan for fuel plan-
ning. The “Change Fields?” option allows
Garmin units in a dual-unit installation. you to select fuel information for each field
Scheduler— displays reminder messages (such as desired.
as “Change oil”, “Switch fuel tanks”, “Overhaul”,
etc.). One-time, periodic, and event-based messages 3a. For point-to-point fuel planning, turn the small
are allowed. One-time messages will appear once and large right knobs to enter the identifier
the timer expires and will reappear each time the of the “from” waypoint. Once the waypoint’s
400W-series unit is powered on, until the message identifier is entered, press ENT to accept the
is deleted. Periodic messages will automatically waypoint. The flashing cursor moves to the
reset to the original timer value, once the message “to” waypoint. Again, turn the small and
large right knobs to enter the identifier of
is displayed. Event-based messages do not use a
the “to” waypoint and press ENT to accept
timer, but rather a specific date and time. the waypoint.
Fuel Planning
To perform fuel planning operations:
1. Select “Fuel Planning” from the flight planning
page.
2. The current fuel planning “mode” is displayed
at the top of the page: “POINT TO POINT” or
“FPL” (for a flight plan). To change the mode, or,
press MENU to display an options window for
190-00356-00 Rev B 151
9 - AUX PAGES
Flight Planning
3b. For flight plan fuel planning, turn the small 7. The flashing cursor moves to the ground speed
right knob to select the desired flight plan by (GS) field. Use the small and large right
number (already stored in memory. “00” is the knobs to enter the ground speed. Press ENT
active flight plan). Turn the large right knob when finished.
to highlight the “LEG” field and turn the small 8. With all variables entered, the following infor-
right knob to select the desired leg of the flight mation will be provided:
plan, or select “Cum” to apply fuel planning • REQ — Quantity of fuel required
calculations to the entire flight plan.
• LFOB — Left-over fuel on board
• LRES — Left-over fuel reserve time
• EFF — Efficiency, expressed in distance per
fuel units (e.g. nautical miles per
gallon)
• RNG — Range (distance)
4. If your fuel management system does not enter
the data automatically, turn the large right • ENDUR —Flight endurance, or total available
knob to highlight the fuel on board (FOB) flight time
field.
Trip Planning
To perform trip planning operations:
1. Select “Trip Planning” from the flight planning
page.
2. The current trip planning “leg mode” is dis-
played at the top of the page: “POINT TO
POINT” or “FPL LEG” (for a flight plan leg). To
change the leg mode, press MENU to display
an options window for the other leg mode, then
press ENT to accept the other leg mode.
3a. For point-to-point trip planning, turn the small
and large right knobs to enter the identifier
of the “from” waypoint. Once the waypoint’s
NOTE: Fuel planning figures can be entered
identifier is entered, press ENT to accept the
and displayed based upon one of three possible waypoint. The flashing cursor moves to the
configurations: “to” waypoint. Again, turn the small and
large right knobs to enter the identifier of
1) No fuel sensors connected—In this instance the “to” waypoint and press ENT to accept
fuel flow is manually entered and is used to the waypoint.
calculate fuel on board. When fuel flow or fuel
on board is manually entered, the figures are
retained the next time you view the page (with
fuel on board continuously recalculated).
2) Fuel flow sensor installed, but no fuel on board
sensor—Fuel on board is manually entered. Fuel
flow is automatically provided by sensor. If fuel
flow is manually entered (to override the sen- OR,
sor), it will not affect the FOB figure and is not 3b. For “flight plan leg” trip planning, turn the
retained the next time you view the page. small right knob to select the desired flight
plan (already stored in memory), by number.
3) Fuel flow and fuel on board sensors in- Turn the large right knob to highlight the
stalled—Fuel flow and fuel on board are “LEG” field and turn the small right knob to
automatically provided by sensors. Fuel on board
select the desired leg of the flight plan, or select
can NOT be entered manually. Fuel flow can be
entered manually, but will not affect the FOB “Cum” to apply trip planning calculations to
figure and is not retained the next time you view the entire flight plan.
the page.
2. As you complete each checklist item, press ENT To insert a checklist step into an existing check-
to move to the next item on the list. list:
1. With the checklists page displayed, turn the
large right knob to select the desired checklist
and press ENT.
2. Turn the large right knob to highlight the
existing checklist entry which will immediately
follow the new checklist step.
To edit a checklist: 3. Turn the small and large right knobs to
enter the new checklist step. Press ENT when
1. With the checklists page displayed, turn the
finished.
large right knob to select the desired checklist
and press ENT. To delete a checklist or all checklists:
2. Press MENU to display an options menu. 1. With the checklists page displayed, press
Select “Edit Item?” and press ENT, then use MENU to display an options menu.
the small and large right knobs to edit each 2. Turn the large right knob to select “delete
checklist item. Press ENT when finished. checklist” or “delete all checklists” and press
ENT to remove the checklist or all checklists
from memory.
To copy a checklist:
1. With the checklists page displayed and the
desired checklist selected, press MENU.
2. Turn the large right knob to select “Copy
Checklist?” and press ENT to copy the check-
list to an empty checklist memory location.
To sort the checklists by name or entry:
1. With the checklists page displayed, press
MENU to display an options menu.
2. Turn the large right knob to select “Sort List
By Entry?” or “Sort List By Name?” and press
ENT.
5. To reset the total trip time, turn the large right RAIM Prediction
knob to highlight “Reset?” and press ENT. To predict RAIM availability:
1. Select “RAIM Prediction” from the utility
page.
Trip Statistics
To reset trip statistics readouts:
1. Select “Trip Statistics” from the utility page. 2. The flashing cursor highlights the waypoint
field. Use the small and large right knobs
to enter the identifier of the waypoint at which
you wish to determine RAIM availability. Press
ENT when finished. (To determine RAIM avail-
ability for your present position, press CLR,
followed by ENT.)
• RAIM Not Available— Satellite coverage is 2. The flashing cursor highlights the waypoint
predicted to NOT be sufficient for reliable field. Use the small and large right knobs
operation during non-precision approaches to enter the identifier of the waypoint at which
you wish to determine sunrise and sunset
• RAIM Available— Satellite coverage is predicted times. Press ENT when finished. (To determine
to be sufficient for reliable operation during sunrise/sunset times for your present position,
all flight phases, including non-precision press CLR, followed by ENT.)
approaches
3. The flashing cursor moves to the date field. Use
NOTE: RAIM computations predict satellite cover- the small and large right knobs to enter the
age within ±15 minutes of the specified arrival date for which you wish to determine sunrise
date and time. Refer to the CDI/Alarms section and sunset times.
of Aux pages Setup 1 for specific information
regarding RAIM protection limits.
To select, highlight
with cursor and press Third Page
ENT. in AUX group
To select a setup item from the setup 1 page: more than 500 feet above or below an airspace, you
1. Press the small right knob momentarily, to will not be notified with an alert message; if you are
activate the flashing cursor. less than 500 feet above or below an airspace and
projected to enter it, you will be notified with an
alert message. The default is 200 feet.
CDI / Alarms— allows you to define the scale for
the 400W-series unit on-screen course deviation
indicator. The scale values represent full scale
deflection for the CDI to either side. The default
setting is “Auto”. At this setting, the CDI scale is
2. Turn the large right knob to select the desired
setup item, and press ENT. set to 2.0 NM during the “en route” phase of flight.
Within 31 NM of your destination airport, the CDI
scale gradually ramps down to 1.0 NM (termi-
nal area). Likewise, when leaving your departure
airport the CDI scale is set to 1.0 NM and gradu-
ally ramps up to 2 NM beyond 30 NM (from the
departure airport). During approach operations
the CDI scale gradually transitions down to an
angular CDI scale. At 2.0 NM of the final approach
fix (FAF), CDI scaling is tightened from 1.0 to the
angular full scale deflection (typically the angular
full-scale deflection is 2.0°, but will be as defined
for the approach).
If a lower CDI scale setting is selected (i.e., 1.0 or
The following setup items are available: 0.3 NM), the higher scale settings are not selected
Airspace Alarms— allows you to turn the during ANY phase of flight. For example, if 1.0 NM
controlled / special-use airspace message alerts on is selected, the 400W-series unit uses this for en
or off. This will not affect the alerts listed on the route and terminal phases and ramps down further
nearest airspace page or the airspace boundaries during an approach. Note that the Horizontal
depicted on the map page. It will simply turn on/off Alarm (HAL) protection limits listed below follow
the warning provided when you are approaching or the selected CDI scale, unless corresponding flight
near an airspace. phases call for lower HAL. For example, if the 1.0
NM CDI setting is selected, full-scale deflection
An altitude buffer is also provided which “expands” during approach will still follow the approach CDI
the vertical range above or below an airspace. For scale settings.
example, if the buffer is set at 500 feet, and you are
Map Datum the United States, all local time offsets will use
be minus, or behind UTC.)
NOTE: Per TSO C146a, the WGS-84 map datum is
used. 4. Press ENT to accept the selected offset.
Restoring Factory Settings
Date / Time
To display local time or UTC:
When making changes to any setup 1 page option,
a “Restore Defaults?” menu selection allows you to
1. Select “Date / Time” from the Setup 1 page. restore the original factory settings (for the selected
2. The flashing cursor highlights the time format item only). For example, with the airspace alarms page
field. Turn the small right knob to display a displayed, the “Restore Defaults?” option will restore
window of available time formats: Local 12hr, all airspace alarms page settings to the original factory
Local 24hr, or UTC. values.
To restore a Setup 1 item to the original factory
settings:
1. Select the desired item from the Setup 1
page.
2. Press MENU to display a page options
window.
3. Continue turning the small right knob to
select the desired time format.
4. Press ENT to accept the selection.
To set the local time:
1. Select “Date / Time” from the Setup 1 page.
2. Turn the large right knob to highlight the
time offset field. 3. With “Restore Defaults?” highlighted, press
ENT.
Setup 2 Page
To select, highlight
with cursor and
press ENT.
The following setup items are available:
Display— allows you to adjust the display for
optimum viewing in any condition. Automatic back-
Fourth Page lighting is available which uses a built-in photocell
in AUX group (at the top left corner of the display bezel) to make
The Setup 2 page provides access to display adjust- the proper display adjustments without any user
ments, parameters which define the nearest airport intervention. Automatic contrast adjustment varies
search, and COM transceiver channel spacing. When the screen contrast level based upon current unit
an item is selected, the corresponding page will appear temperature. You may also select manual control of
providing access to the various unit settings. the display contrast and backlighting to tailor the
400W-series unit display to your needs.
To select an item from the Setup 2 page:
NOTE: Display backlighting changes are not
1. Press the small right knob momentarily, to saved when the 400W-series unit is turned off.
activate the flashing cursor. Backlighting will revert to the “Auto” setting the
next time the unit is turned on.
COM Configuration— allows you to select 8.33 4. Turn the large right knob to highlight the
kHz or 25.0 kHz COM frequency channel spacing. right (decimal) part of the frequency field.
NOTE: 8.33 kHz VHF communication frequency
channel spacing is not approved for use in the
United States. Select the 25.0 kHz channel spac-
ing option.
NOTE: Exercise caution when changing the Near- 3. Turn the small right knob to select “On” or
est Airport Criteria. Remember, by excluding cer- “Off” and then press ENT. Press the small
tain surface types or shorter runway lengths, you right knob to exit WAAS selection.
may be excluding airports from the list that are
more than adequate for an emergency landing! Restoring Factory Settings
Blank Page
Abort Approach — Loss of Navigation — Execute Approaching VNAV profile — You are within one minute
missed approach using other navigation equipment. of reaching the initial Vertical Navigation descent point.
Airport terrain database integrity error — The 400W- APR Guidance Available - Use PROC before A/P APR
series unit has detected a problem with a database on the — For units configured with the KAP140 or KFC225
TAWS/Terrain data card. The message “<database name> autopilot, this message reminds pilots, when they turn
database integrity error” indicates the data base in error. on course to the FAF, that they need to enable autopilot
The data is not usable and the card should be returned to outputs (by pressing PROC and selecting “Enable A/P APR
your Garmin dealer. Outputs?”) before switching the autopilot control panel to
APR.
Airspace ahead — less than 10 minutes — Your GPS-
calculated course is projected to enter a special use airspace Arrival at waypoint [waypoint name] — You are within
within 10 minutes. This message is automatically disabled the arrival alarm circle for the indicated waypoint. The size
within 30 nautical miles of an arrival airport, when an of the arrival alarm circle is defined from the “CDI / alarms”
approach is loaded. menu option on the Setup Page.
Airspace near and ahead — Your GPS-calculated posi- Aviation database integrity error — The 400W-series
tion is within 2 nautical miles of the boundary of a special unit has detected a problem with a database on the
use airspace and your course is projected to enter the NavData® card. The message “<database name> database
airspace within 10 minutes. This message is automatically integrity error” indicates the data base in error. The data is
disabled within 30 nautical miles of an arrival airport, when not usable and the card should be returned to Jeppesen or
an approach is loaded. your Garmin dealer for service.
All data referenced to True North — the unit’s Heading Bad geometry, parallel offset not activated — parallel
mode has been set to “True” in the AUX Setup pages. offset is not activated because of flight plan geometry.
DIS
your desired course on an active flight plan or direct-
BRG to.
TRK ETA (estimate time of arrival)— The estimated time
XT
K
at which you will reach your destination waypoint,
based upon current speed and track.
E
ETE (estimated time en route)— The time it will
N
LA take to reach the destination waypoint, from present
RP
S AI position, based upon current ground speed.
G
Vertical
Navigation
VE
RT
IC
AL
NA
VI
G
AT
TO PROFILE
N
PR
O
FI
TIC
AND POSITION AL
SPE
ED
RE
QU
IRE
D
TARGET ALTITUDE
AND POSITION
DISTANCE TO TARGET
AIRPORT
What happens when I select an approach? Can I store a Can I file slant Golf (“/G”) using my GPS?
flight plan with an approach, departure or arrival?
Yes, you may file your flight plan as /G if your 400W-
Whenever you load an approach, departure or arrival
series unit is an authorized IFR installation. The 400W
into the active flight plan, a set of approach, departure or
series is a TSO C146a Gamma-3 (Class 3) authorized
arrival waypoints is inserted into the flight plan—along
GPS navigator. If you are flying en route, you may file
with a header line describing the instrument procedure
/G with an expired database only after you have verified
you selected. The original en route portion of the flight
all route waypoints. Approaches may not be flown with
plan will remain active, unless you “Activate” the instru-
an expired database. See your approved Airplane Flight
ment procedure; which may be done when the procedure
Manual Supplement for more information.
is loaded or at a later time.
What does the OBS key do and when do I use it?
The OBS key is used to select manual (OBS mode) or
to suspend automatic sequencing of waypoints. Activat-
ing OBS mode (as indicated by an annunciation
directly above the OBS key) holds your current “active to”
waypoint as your navigation reference and prevents the
GPS from sequencing to the next waypoint. When OBS
Flight plans can also be stored with an approach, de- mode is cancelled, automatic waypoint sequencing is se-
parture or arrival. Keep in mind that the active flight plan lected, and the 400W-series unit will automatically select
is erased when the unit is turned off and overwritten when the next waypoint in the flight plan once the aircraft has
another flight plan is activated. When storing flight plans crossed the present active-to waypoint.
with an approach, departure or arrival, the 400W-series
unit will use the waypoint information from the cur- NORMAL OBS
rent database to define the waypoints. If the database is (no “OBS” annunciator)
changed or updated, the 400W-series unit will automati- Automatic sequencing of Manual sequencing-
cally update the information if the procedure has not been waypoints “holds” on selected
modified. If an approach, departure or arrival procedure waypoint
is no longer available, the flight plan will become locked Change in HSI does not Manually select course to
until the procedure is deleted from the flight plan or the affect CDI deflection next waypoint from HSI
correct database is installed. For information on loading
Always navigates “TO” the Will indicate “TO” or
an approach, departure or arrival. See Section 4 - Flight
active waypoint “FROM” waypoint
Plans for instructions on saving and copying flight plans.
Must be in this mode for Cannot be set for final ap-
final approach course proach course or published
holding patterns
Whenever OBS mode is active, the 400W-series unit
allows you to select the desired course to/from a waypoint
using the HSI (much like a VOR) and display a to/from
190-00356-00 Rev B 193
APPENDIX C
Troubleshooting Q & A
flag for the active-to waypoint. If an external course in- When should I use the OBS key to return to auto
put is not available, you may select the OBS course on- sequencing, and what happens when I do?
screen, via a “Select OBS Course” pop-up window. With The most common application for using the OBS key
OBS mode cancelled, the CDI will always display a “TO” is the missed approach. The 400W-series unit will suspend
indication for the next waypoint once you’ve crossed the automatic waypoint sequencing (indicated by a “SUSP” an-
active waypoint (provided the active waypoint is not the nunciation directly above the OBS key; see right) when
last waypoint). Refer to Section 5 - Flying the Missed Ap- you cross the missed approach point (MAP). This prevents
proach for an example using the OBS key. the 400W-series unit from automatically sequencing to
the missed approach holding point (MAHP). If a missed
approach is required, press the OBS key to return to au-
tomatic waypoint sequencing and sequence the approach
to the MAHP. See Section 5 - Flying the Missed Approach for
more information on missed approaches.
How do I skip a waypoint in an approach, departure, when you are to begin the turn. Set the HSI to the
or arrival? next DTK value and begin the turn.
The 400W-series unit allows you to manually select 3) The To/From indicator on the HSI (or CDI) will
any approach, departure or arrival leg as the active leg of flip momentarily to indicate that you have crossed
your flight plan. This procedure is performed from the the midpoint of the turn. For more information on
active flight plan page by highlighting the desired waypoint waypoint alerts and turn advisories, see section 5.
and pressing direct-to twice, then ENT to approve the se- When does the CDI scale change, and what does it
lection (see illustration right). The GPS will then provide change to?
navigation along the selected flight plan leg, so be sure
The 400W-series unit begins a smooth CD`I scale tran-
you have clearance to that position.
sition from the 2.0 NM (en route mode) to the 1.0 NM
(terminal mode) scale within 31 NM from the destination
airport (see below). The CDI scale further transitions to
2.0° angular (approach mode) at 2 NM prior to the FAF
during an active approach CDI scaling is tightened from
1.0 NM to the angular full scale deflection (typically the
angular full-scale deflection is 2.0°, but will be as defined
for the approach.
NOTE: If activating a leg while on the From side,
sequencing will be suspended as indicated with If you are in a missed approach situation and would
the SUSP annunciation shown above the OBS like to return the CDI to the 1.0 NM scale, activate the
key. missed approach sequence by pressing the OBS key after
you pass the MAP and the annunciation in the lower left
How do I fly the GPS with an autopilot and DG head-
ing bug? of the screen changes from MAPR to TERM, as described
If you do not have an HSI, you should make your in Section 5 - Procedures - Flying the Missed Approach.
course selections on the external CDI’s OBS knob and the For this to occur however, the course to the MAHP must
DG heading bug. be greater than 3° away from the course line to the run-
way. The CDI scale is also 1.0 NM (terminal mode) within
When does turn anticipation begin, and what bank
31 NM of the departure airport.
angle is expected?
The 400W-series unit will smooth adjacent leg transi-
tions based upon a nominal 15º bank angle (with the abil-
ity to increase the bank angle up to 30º) and provide three
pilot cues for turn anticipation:
1) A waypoint alert (“LT or RT to ###° x S”) will flash
in the lower right corner of the screen 10 seconds
before the turn point.
2) A flashing turn advisory (“LT or RT TO ###° NOW”)
will appear in the lower right corner of the screen
±1 NM
Origin = 10,000 ft
past MAP
FAF MAP
IAF
+350 ft
±2 degree
angular
1 1
NM NM
What is the correct missed approach procedure? How To activate a new approach to a different airport, press
do I select the missed approach holding point? direct-to and select the desired airport using the small
The 400W-series unit does not automatically sequence and large right knobs. Press ENT to accept the selected
past the MAP. Waypoint sequencing to the first waypoint airport, then follow the steps in the preceding paragraph
in the missed approach procedure will be enabled when to select an approach for the new airport. See section 5 for
the OBS key is pressed after crossing the MAP. All pub- more information on selecting and activating approaches.
lished missed approach procedures must be followed, as
NOTE: Do not attempt to reactivate the same ap-
indicated on the approach plate. proach you’re currently on, prior to crossing the
To execute the missed approach procedure prior to missed approach point (MAP). If you attempt to
the MAP (not recommended), select the active flight plan do so, an alert message (“Are you sure you want
page and use the direct-to key (by pressing it twice) to to discontinue the current approach?”) appears.
activate the missed approach portion of the procedure. If you still proceed with reactivating the ap-
proach, the 400W-series unit directs you back to
How do I re-select the same approach or activate a new the transition waypoint and does NOT take into
approach after a missed approach? consideration any missed approach procedures.
After flying all missed approach procedures, you may
reactivate the same approach for another attempt from the
procedures page. Once you have been given clearance for
another attempt, activate the approach from the procedures
page by highlighting “Activate Approach?” and then press-
ing ENT. The 400W-series unit will provide navigation
along the desired course to the waypoint and rejoin the
approach in sequence from that point on. See Section 4
- Active Flight Plan Leg Selection for information on activat-
ing a specific flight plan leg.
To activate a new approach for the same airport, se-
lect the new procedure from the procedures page. To view
the procedures page, press PROC and turn the large right
knob to highlight “Select Approach?”. Press ENT and turn
the large right knob to highlight the new approach you
want to fly. Press ENT to select the approach, then select
the desired transition. Finally, highlight “Activate?” at the
bottom right corner of the screen and press ENT to acti-
vate the new approach.
H Panning 35
HFOM 56 Scale 33, 117
Hold 89, 183 Setup 37
HSI 61, 148, 193 Symbols 33
MAPR 83
I Measure dist? 39
Ident audio and volume 145 Menu 3
IFR 17 Messages 4, 8, 177
IFR procedures 17 Minimum safe altitude 52, 189
ILS 102, 168 Missed approach 88, 197
ILS CDI Selection 103, 110, 166, 168 Model descriptions 1
Inhibit terrain 43 MSA 52, 189
Inside airspace 20 MSG 4
Instrument panel self-test 6
Integ 8, 159, 185, 192 N
Interfaces 191 Navcom 15, 51
Intersection 125, 137 NavData Card 190
IOI 50 Navigation database 46
Navigation Terms 188
J Nav pages 12, 29
Jeppesen 190 On-screen data 31
NDB 125, 137
K
Nearest 4, 18, 133
Key descriptions 2 Airport 171, 173
Key stuck 178 Airspace 20, 140
King autopilot 112 ARTCC 138
Knob descriptions 2 FSS 139
L Intersection 137
LFOB 152 Navigate to 135
LNAV/VNAV Approach 83, 108 NDB 137
Localizer 145, 191 User waypoint 138
Localizer Approach 110 VOR 137
Low alt 83 Next FPL airport 116, 118, 120, 122, 123, 124
LPV Approach 83, 107 NRST 4
LRES 152 O
M OBS 4, 181, 193
Magnetic variation 166, 168 OCN 83
Map Odometer 162
Auto zoom 34 P
Create user waypoint 129 Packing list iii
Data fields 40 Page groups 10, 29
Datum 166, 170, 181 Panning 35
Page 14, 32
200 190-00356-00 Rev B
APPENDIX D
Index
Garmin Corporation
No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
www.garmin.com