Professional Documents
Culture Documents
Quick Start 6) Connect the GND pad of the MAX25601 board to the
LED1- pad of the MAX25608 board.
Required Equipment 7) Connect the MAX32625PICO# to the MAX25608EV-
● MAX25608 EV system SYS using the included ribbon cable.
● MAX32625PICO# (included) 8) Connect the MAX32625PICO# to the computer with
the included USB cable.
● Windows® 10 computer with GUI installed
9) If the GUI is not yet installed, install the GUI.
● 12V, 5A power supply 10) Run the GUI.
11) Click the Connect button and choose device 08
Procedure
to communicate with the MAX25608 IC driving the
The EV system is fully assembled and tested. Use the LEDs connected between LED1+ and LED1-.
following steps to verify board operation. 12) A separate current source needs to be used for driv-
Caution: Do not turn on the power supply until all ing the LEDs between LED2+ and LED2- pads. The
connections are made. Additional caution should be MAX25608 IC device ID for this is 04.
taken; the on-board LEDs are very bright when illu-
minated.
Detailed Description
The MAX25608 evaluation system (EV system) provides
1) Connect the positive terminal of the +12V power
a proven design to evaluate the MAX25608 12 chan-
supply to the VIN pad of the MAX25608 board.
nel LED matrix manager. The EV system includes two
2) Connect the ground terminal of the +12V power
instances of the MAX25608 controlling 12 on-board LEDs
supply to the GND pad of the MAX25608 board.
connected in a series configuration. The MAX25601
3) Connect the positive terminal of the +12V power
boost-buck LED driver is also included to drive one of the
supply to the IN pad of the MAX25608 board.
strings of 12 LEDs. A separate current source is needed
4) Connect the ground terminal of the +12V power
to drive the second set of LEDs connected between
supply to the GND pad of the MAX25601 board.
LED2+ and LED2-.
5) Connect the LED+ pad of the MAX25601 board to
the LED1+ pad of the MAX25608 board.
Ordering Information
PART TYPE
MAX25608EVSYS# EV System
#Denotes RoHS compliance.
PACKOUT (These are purchased parts but not assembled on PCB and will be shipped with PCB)
ITEM REF_DES DNI/DNP QTY MFG PART # MANUFACTURER VALUE DESCRIPTION COMMENTS
MODULE; BOARD; MAX32625PICO BOARD
DESIGN FOR MAX32625 ARM CORTEX-M4F;
BOARD; LAMINATED PLASTIC WITH COPPER
1 U4 - 1 MAX32625PICO MAXIM MAX32625PICO
CLAD; NOTE: SOCKETED FOOTPRINT USING
BCS-110-L-S-TE CONNECTOR WITH MATING
CONNECTOR TSW-110-07-F-S
MAX25601 EVKIT; Current source for
2 U5 - 1 MAX25601EVKIT# MAXIM MAX25601EVKIT#
MAX25608 Matrix manager
TOTAL 134
www.maximintegrated.com
20K R6
20K R64
DR5
DR7
20K R10
20K R65
DR4
DR8
20K R11
20K R7
DR3
DR9
20K R67
20K R5
MAX25608 EV Kit Schematics
DR2
DR10
MAX25608 Evaluation System
20K R68
20K R8
DR1
DR11
20K R69
20K R9
SRC1
DR12
R46 U1
VDD_IC
MAX25608AUI/V+
0
R48
10K
DR12 DR11 DR10 DR9 DR8 DR7 SRC7 DR6 DR5 DR4 DR3 DR2 DR1 SRC1
J48
FTSH-105-01-L-DV-K
TP5 FLT
PICO_AIN_1 1 2 PICO_P3_3
3 4 PICO_P3_2
5 6 PICO_RX_2
PICO_NC 7 8 PICO_TX_2
9 10 PICO_P3_7 PICO_TX_2 RXOUT
R52 0
TP3 RX RX
PICO_AIN_3
PICO_RX_2 R45
PICO CONNECTOR R50 0
TP4 TX TX
0
DNI
PICO_RX_2_R50 TXOUT R57
49.9
R2 R3
VDD_IC TP1 CLKIN CLKIN CLKOUT CLKOUT TP8
0 RADDR 0
R56
49.9
R49
DNI
R13
1.05K
C34
0.1UF
R1 2.2UF
C35
BAT_VIN IN_U1 VDD_IC_R14
TP2
C19 0
RT1
10K
1UF
0.1UF
C1
0.1UF
C37
R12
1.05K
R23 R41
10K
10K
PICO_RX_2_R50 R53 R54
TP7
TP6
0 0
PICO_TX_2
Evaluates: MAX25608
Maxim Integrated │ 8
S_SRC7
S_DR6
www.maximintegrated.com
20K R28
20K R29
S_DR5
S_DR7
20K R15
20K R30
S_DR8 S_DR4
20K R16
20K R34
S_DR3
S_DR9
MAX25608 Evaluation System
20K R31
20K R22
S_DR2
S_DR10
20K R32
20K R35
S_DR1
S_DR11
MAX25608 EV Kit Schematics (continued)
20K R33
20K R36
S_SRC1
S_DR12
R51 U2
VDD2_IC
MAX25608AUI/V+
0
R21
10K
DR12 DR11 DR10 DR9 DR8 DR7 SRC7 DR6 DR5 DR4 DR3 DR2 DR1 SRC1
TP18 FLT
0
TXOUT R24 S_TXOUT
TX TX
0
R27
49.9
R19 R20
TP17 CLKOUT CLKIN CLKOUT CLKOUT2 TP19
0 RADDR 0
R26
49.9
VDD2_IC
R44
536
VDD2_IC
R18
432
C4
0.1UF
C5
C3 0
RT2
10K
1UF
0.1UF
C2
0.1UF
C6
R17
1.05K
Evaluates: MAX25608
Maxim Integrated │ 9
TP15
TP13
R42
0
TP12
TP9
R38
0
S_DR12 S_DR6
www.maximintegrated.com
DR12 DR6
1
1
1
1
3
3
D12
D18
3
3
D34
D6
2
2
S_DR11 S_DR5
2
2
DR5
1
DR11
1
3
3
D19
D13
3
D7
3
D1
2
2
MAX25608 Evaluation System
S_DR10 S_DR4
2
DR4
1
DR10
1
3
3
D20
D14
3
D8
3
D2
2
S_DR3
2
S_DR9
2
DR3
1
MAX25608 EV Kit Schematics (continued)
DR9
1
3
3
D21
D15
3
D9
3
D3
2
2
S_DR8 S_DR2
2
DR8 DR2
1
1
3
3
D22
D16
3
3
D10
D4
2
2
S_DR7 S_DR1
1
DR7 DR1
1
3
3
D23
D17
3
3
D11
D5
2
S_SRC1
2
S_SRC7
2
SRC7 SRC1
R43
0
TP14
R40
0 TP16
R39
0
TP10 R37 TP11
0
DNI
DNI
Evaluates: MAX25608
Maxim Integrated │ 10
MAX25608 Evaluation System Evaluates: MAX25608
Revision History
REVISION REVISION PAGES
DESCRIPTION
NUMBER DATE CHANGED
0 8/21 Initial release —
For pricing, delivery, and ordering information, please visit Maxim Integrated’s online storefront at https://www.maximintegrated.com/en/storefront/storefront.html.
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses
are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. © 2021 Maxim Integrated Products, Inc. │ 13