Professional Documents
Culture Documents
Users Manual
11/99
ii
iii
iv
vi
vii
viii
1-1
WWarning
To avoid possible electric shock or personal injury, follow these guidelines:
• Do not use the meter if it is damaged. Before you use the meter, inspect the case. Look for cracks or
missing plastic. Pay particular attention to the insulation surrounding the connectors.
• Inspect the test leads for damaged insulation or exposed metal. Check the test leads for continuity.
Replace damaged test leads before you use the meter.
• Do not use the meter if it operates abnormally. Protection may be impaired. When in doubt, have the
meter serviced.
• Do not operate the meter around explosive gas, vapor, or dust.
• Do not apply more than the rated voltage, as marked on the meter, between terminals or between any
terminal and earth ground.
• Before use, verify the meter’s operation by measuring a known voltage.
• When measuring current, turn off circuit power before connecting the meter in the circuit. Remember
to place the meter in series with the circuit.
• When servicing the meter, use only specified replacement parts.
• Use caution when working above 30 V ac rms, 42 V peak, or 60 V dc. Such voltages pose a shock
hazard.
• Avoid working alone.
1-2
WWarning
• When using the probes, keep your fingers behind the finger guards on the probes.
• Connect the common test lead before you connect the live test lead. When you disconnect test leads,
disconnect the live test lead first.
• Remove test leads from the meter before you open the battery door.
• Do not operate the meter with the battery door or portions of the cover removed or loosened.
• To avoid false readings, which could lead to possible electric shock or personal injury, replace the
batteries as soon as the low battery indicator (M) appears.
• Use only type AA batteries, properly installed in the meter case, to power the meter.
• To avoid the potential for fire or electrical shock, do not connect the thermocouples to electrically live
circuits.
Caution
To avoid possible damage to the meter or to the equipment under test, follow these guidelines:
• Disconnect circuit power and discharge all high-voltage capacitors before testing resistance,
continuity, diodes, or capacitance.
• Use the proper terminals, function, and range for your measurements.
• Before measuring current, check the meter’s fuses and turn power OFF to the circuit before
connecting the meter to the circuit.
1-3
Symbols
Symbols used on the meter and in this manual are
explained in Table 1-2.
1-4
2-1
2-2
2-3
Rotary Switch The rotary switch is shown in Figure 2-2. Each position is
described in Table 2-1.
Turn the meter on by selecting any measurement function
(identified with white letters around the rotary switch). The
meter presents a standard display for that function (range, nS
measurement units, modifiers, etc.) The display may also
be influenced by some of the choices made in Setup.
mV F
Use the blue button to select any rotary switch alternate ac+dc C
function (labeled in blue letters). You can also use other A
buttons to choose modifiers for the selected function. V
ac+dc mA
When you turn the rotary switch from one function to
another, a display for the new function appears. Button mV A
choices made in one function do not carry over into dB
another function.
A
With Model 89, a VIEW MEM switch position is available; V mA
dB ac+dc
refer to Chapter 4 for more information.
OFF A
ac+dc
VIEW MEM
CLEAR MEM
tc012f.eps
Figure 2-2. Rotary Switch
2-4
blue for some of the rotary switch positions. Table 2-1 Hz % ms RANGE
defines all blue button functions.
SETUP
2-5
2-6
VIEW (Model 89 only.) Access data held in the meter’s CLEAR MEM. See Chapter 4 for more information.
MEM memory. See Chapter 4 for more information.
2-7
Yellow Button
Button Description Function Description
Note
Press O to access “Yellow Button Functions.” The O box and the 24-hour clock appear in the lower corners
of the display and the primary display freezes, allowing time to press a second button.
T Press to turn backlight on or off. Also, in Setup, use SETUP Press to access Setup selections.
l the arrow function (l) to select the previous digit or O T Press to store a Setup selection and
item in a list. proceed to the next selection.
Q Press to freeze the displayed value. Press again to AutoHOLD Press to begin AutoHOLD; the last
release the display. O Q stable reading is displayed.
M Press to start retaining min, max, and average values. FAST MN MX Press to start FAST MN MX mode,
Press successively to display max, min, and average O M where min and max values for short
values. Press O N (CANCEL) to stop. duration events are stored.
D Press to store the present reading as an offset LOGGING Press to start Logging (Model 89).
reference; subsequent readings show only the relative O D Press O + N (CANCEL) to
difference from this value. Press again to show the stop.
difference as a percentage of the reference.
2-8
Yellow Button
Button Description Function Description
• In Setup, increment a digit . (none)
[ • In counter functions, select positive pulse slope.
• In ohms continuity, select beep on open.
• In VIEW MEM, see Chapter 4.
] • In Setup, decrement a digit . (none)
• In counter functions, select negative pulse slope.
• In ohms continuity, select beep on short.
• In VIEW MEM, see Chapter 4.
R Exit AUTO and enter MANUAL ranging. In MANUAL, SAVE Press to save present reading
select next input range. Press O N O R (Model 89)
(CANCEL) to return to AUTO.
N Successively press for frequency, duty cycle, and CANCEL CANCEL any % (blue key) function
pulse width. O N and all other button features.
2-9
2-10
2-11
8 10 12
7 9 11
5 13
4
3
2
1 14
17 16 15
tc011f.eps
Figure 2-4. Display Features
2-12
-
reference value shown in the secondary display.
E Indicates negative readings. In Relative mode, this sign indicates that the present input
is less than the stored reference.
F Z >30 V ac and/or dc is present at the input terminals.
G B Low battery. If flashing, battery failure is imminent, and logging and backlight are
disabled.
WWarning
To avoid false readings, which could lead to possible electric shock or personal
injury, replace the battery as soon as the low battery indicator appears.
2-13
K gS AutoHold is active. ( O + Q)
0L Overload input.
M Measurement Units
dBm, dBV For ac volts functions, reading is shown in decibels of power above or below 1 mW
(dBm) or decibels of voltage above or below 1 V (dBV).
2-14
M AC+DC For dc volts and dc amps functions, reading represents the rms total of ac and dc
measurements.
2-15
N 51000
MANUAL
Range. Digits display range in use.
AUTO
O Time Display. Used with HOLD, AutoHOLD, MIN MAX, FAST MN MX, SAVE, and
LOGGING (Model 89).
fMS88:88 Elapsed Time Display (f on): shown in minutes:seconds to maximum of 59:59 - used if
time since Min, Max, or Logging started is less than 60 minutes. Always used for Min,
Max, Avg. Displays hours:minutes after 1 hour.
HM 88:88 24-hour Display (f off): shown in hours:minutes to maximum of 23:59. For setting the
24-hour clock, refer to Chapter 5.
Q MEM Memory Index Display (Model 89). Also used for dBm reference resistance.
2-16
stop you from attempting to measure voltage, continuity, Figure 2-5. Input Terminals
resistance, capacitance, or diode values when the leads
are plugged into a current terminal.
2-17
If you remove the test leads (open the input), the meter
retains the last frozen primary display.
2-18
The time elapsed since the MIN MAX mode was entered The MIN MAX mode is appropriate for storing signal
is shown in the bottom right corner of each type of display. events that last 50 ms or longer in most measurement
See Figure 2-7. functions. Signal events must be 500 ms or longer in the
following functions: continuity, conductance, capacitance,
temperature, Hz, duty cycle, and pulse width.
2-19
Using FAST MN MX
FAST MN MX can capture transient signal events as short
as 250 µs, but with decreased accuracy; only 3-1/2 display
digits are allowed.
tc033f.eps
Figure 2-7. Min Max Avg
2-20
2-21
2-22
3-1
Measuring AC Voltage
The meter presents ac voltage values as rms (root mean
square) readings. The rms value is the equivalent dc AutoHOLD
HOLD
FAST MN MX
MIN MAX
LOGGING
REL
YES
F
mV
true rms readings, which are accurate for sinewaves and ac+dc
ac+dc V
C
A
mA
other wave forms (with no dc offset) such as square dB mV A
tc001f.eps
Figure 3-1. AC Voltage Measurement
3-2
Note
If dBm is displayed, check that the reference
resistance value closely matches the impedance
of the system being measured.
3-3
• For dBm, Vr is the voltage across the reference Both AC and DC Voltage Measurements
resistance at 1 mW. For example, Vr would be When a dc volts function is selected, the meter can
0.7746 V with a 600 Ω reference resistance. display ac and dc components of a signal separately or
the combined ac + dc (rms) value.
• For dBV, the reference voltage (Vr) is 1 V.
To select separate ac and dc signal components:
3-4
tc024f.eps
Figure 3-3. AC and DC Display
3-5
Measuring Resistance
89 LOGGING MULTIMETER
Caution
To avoid possible damage to the meter or to
the equipment under test, disconnect circuit
power and discharge all high-voltage
AutoHOLD
HOLD
FAST MN MX
MIN MAX
LOGGING
REL
YES
capacitors before measuring resistance.
CANCEL SAVE NO
Hz % ms
SETUP
nS
RANGE
Resistance is an opposition to current flow. The unit of
mV
F resistance is the ohm (Ω). The meter measures resistance
ac+dc V ac+dc C
A
ac+dc V mA by sending a small current through the circuit.
dB mV A
A
dB V
A
mA
ac+dc
The meter’s resistance ranges are 500.00 Ω, 5.0000 kΩ,
OFF
50.000 kΩ, 500.00 kΩ, 5.0000 MΩ, and 30.000 MΩ.
ac+dc
VIEW
CLEAR MEM
TEMPERATURE
mA
A
10A MAX
A COM V
To measure resistance, set up the meter as shown in
400mA CAT
Figure 3-5.
FUSED
FUSED 1000V
tc002f.eps
Figure 3-4. DC Voltage Measurement
3-6
Circuit Power
OFF
1
3 2
89 LOGGING MULTIMETER
Disconnect
1 2
AutoHOLD FAST MN MX LOGGING YES
F
ac+dc mV C
A
ac+dc V mA
dB mV A
V A
dB
mA
ac+dc
OFF A
ac+dc
VIEW
CLEAR MEM
TEMPERATURE
mA
A A COM V
10A MAX
FUSED 400mA CAT
FUSED 1000V
Disconnect
tc004f.eps
Figure 3-5. Resistance Measurement
3-7
Keep the following in mind when measuring resistance: Testing for Continuity
• Because the meter’s test current flows through all Caution
possible paths between the probe tips, the measured To avoid possible damage to the meter or to
value of a resistor in a circuit is often different from the equipment under test, disconnect circuit
the resistor’s rated value. power and discharge all high-voltage
• The test leads can add 0.1 Ω to 0.2 Ω of error to capacitors before testing for continuity.
resistance measurements. To test the leads, touch Continuity is the presence of a complete path for current
the probe tips together and read the resistance of the flow. The continuity test features a beeper that sounds if a
leads. If necessary, you can press D to circuit is complete. The beeper allows you to perform
automatically subtract this value. quick continuity tests without having to watch the display.
The resistance function can produce enough voltage to The continuity function detects intermittent opens and
forward-bias silicon diode or transistor junctions, causing shorts lasting as little as 1 millisecond (0.001 second).
them to conduct. To avoid this, do not use the 30 MΩ These brief contacts cause the meter to emit a short beep.
range for in-circuit resistance measurements.
To select continuity, turn the rotary switch to resistance
position, then press the blue button once. The continuity
symbol (~) appears in the display. Continuity uses
manual ranging only; autoranging is not available. Refer to
Figure 3-6 for continuity testing setup instructions.
3-8
• Frequency ( N)
• FAST MN MX ( O M)
• Manual ranging ( R)
3-9
Press
for beep
89 LOGGING MULTIMETER
2 89 LOGGING MULTIMETER
on open
Press
for beep
on short
AutoHOLD FAST MN MX LOGGING YES AutoHOLD FAST MN MX LOGGING YES
Hz % ms RANGE Hz % ms RANGE
SETUP SETUP
nS nS
ac+dc mV C
F
ac+dc mV C
F OFF
ac+dc V
A
mA OFF ac+dc V
A
mA (open)
dB mV A 1 (open) dB mV A
A V A
V
dB
A
mA
ac+dc Press to dB
A
mA
ac+dc
OFF
OFF
VIEW
CLEAR MEM
ac+dc
select “ .” VIEW
CLEAR MEM
ac+dc
TEMPERATURE TEMPERATURE
mA mA
A COM V A A COM V
A
ON ON
(closed) (closed)
tc003f.eps
Figure 3-6. Continuity Test
3-10
CANCEL SAVE NO
Hz % ms RANGE
SETUP
nS
ac+dc mV C
F Press twice to
ac+dc V
A
mA select nS.
dB mV A
V A
dB
mA
ac+dc
OFF A
ac+dc
VIEW
CLEAR MEM
TEMPERATURE
mA
A A COM V
10A MAX
FUSED 400mA CAT
FUSED 1000V
tc023f.eps
Figure 3-7. Conductance Measurement
3-11
Capacitance is the ability of a component to store an The following are some tips for measuring capacitance:
electrical charge. The unit of capacitance is the farad (F).
• To speed up measurements of similar values, press
Most capacitors are in the nanofarad (nF) to microfarad
R to manually select the proper range.
(µF) range.
• To improve the measurement accuracy of small value
The meter measures capacitance by charging the
capacitors, press D with the test leads open to
capacitor with a known current for a known period of time,
subtract the residual capacitance of the meter and
measuring the resulting voltage, then calculating the
leads.
capacitance. Capacitors larger than 100 µF take several
seconds to charge. The capacitor charge can be up to 3
V.
3-12
CANCEL SAVE NO
F
controlled rectifiers (SCRs), and other semiconductor
ac+dc mV C
ac+dc V
A
mA devices. The test sends a current through a
dB mV A
semiconductor junction, then measures the junction’s
V A
dB
A
mA
ac+dc voltage drop. A typical junction drops 0.5 V to 0.8 V. In
OFF
diode test, the beeper is active. It beeps briefly for a
ac+dc
VIEW
CLEAR MEM
mA
TEMPERATURE
V
normal junction and is on continuously if a short is
A A COM
10A MAX
FUSED 400mA CAT
detected.
FUSED 1000V
3-13
Typical
Reading
89 LOGGING MULTIMETER 89 LOGGING MULTIMETER
Hz % ms RANGE Hz % ms RANGE
SETUP SETUP
nS nS
ac+dc mV C
F Forward Bias ac+dc mV C
F Reverse Bias
A A
ac+dc V mA ac+dc V mA
dB mV
V A
A Press for + dB mV
V A
A
+
dB
mA
ac+dc Diode Test dB
mA
ac+dc
OFF A OFF A
ac+dc ac+dc
VIEW VIEW
CLEAR MEM CLEAR MEM
TEMPERATURE TEMPERATURE
mA mA
A A COM V A A COM V
tc006f.eps
Figure 3-9. Diode Test
3-14
HOLD
FAST MN MX
MIN MAX
LOGGING
REL
YES
CANCEL SAVE NO
Hz % ms RANGE
mV A
terminals. dB V A
mA
ac+dc
OFF A
ac+dc
3-15
3-16
3-17
Measuring AC Current
To measure ac current, set up the meter as shown in
Figure 3-11.
3-18
AutoHOLD FAST MN MX LOGGING YES AutoHOLD FAST MN MX LOGGING YES AutoHOLD FAST MN MX LOGGING YES
HOLD MIN MAX REL HOLD MIN MAX REL HOLD MIN MAX REL
F F F
ac+dc mV C
A A ac+dc mV C
A A ac+dc mV C
A
ac+dc V mA mA ac+dc V mA mA ac+dc V mA
dB mV A dB mV A dB mV A A
V A V A V A
dB
mA dB
mA dB
mA
ac+dc ac+dc ac+dc
mA mA mA
A A COM V A A COM V A A COM V
tc008f.eps
Figure 3-11. AC Current Measurement
3-19
3-20
89 LOGGING MULTIMETER
CANCEL SAVE NO
SETUP
Hz % ms
nS
RANGE
Current through one component
F
ac+dc mV C
A
ac+dc V mA
mV A A
dB
A
mA
dB V mA
ac+dc
ac+dc
OFF A
ac+dc
TEMPERATURE
mA
A A COM V
10A MAX
FUSED 400mA CAT
FUSED 1000V
tc007f.eps
Figure 3-12. DC Current Measurement
3-21
Measuring Frequency nS
Frequency is the number of cycles a signal completes
each second. The meter measures the frequency of a
mV F
voltage or current signal by counting the number of times ac+dc C
the signal crosses a threshold level each second. A
Figure 3-13 highlights the function selections that allow
V
ac+dc mA
frequency measurement.
tc021f.eps
Figure 3-13. Functions Allowing Frequency
Measurement
3-22
The meter beeps to indicate when a particular pushbutton Measuring Duty Cycle
is not allowed when measuring frequency. The following
are some general rules. Duty cycle (or duty factor) is the percentage of time a
signal is above or below a trigger level during one cycle
• Relative ( D), Hold ( Q), and MIN MAX (Figure 3-15).
( M)can be used.
The duty cycle mode is optimized for measuring the on or
• FAST MN MX ( O M) cannot be used. off time of logic and switching signals. Systems such as
electronic fuel injection systems and switching power
supplies are controlled by pulses of varying width, which
can be checked by measuring duty cycle.
3-23
+Slope -Slope
Trigger Point Trigger Point
30% Above
Trigger
Point
100%
-Slope +Slope
Trigger Point Trigger Point
70% Below
Trigger Point
100%
tc009f.eps
Figure 3-15. Duty Cycle Measurements
3-24
tc027f.eps
Figure 3-16. Duty Cycle Display
3-25
+Slope
Trigger Point
Pulse
Width
1
Period = Frequency
-Slope
Trigger Point
Pulse Width
Period
tc020f.eps
Figure 3-17. Pulse Width Measurements
3-26
3-27
3-28
4-1
Stopping Logging
Logging stops when one of the following occurs:
• You press O N (CANCEL).
• A flashing low battery condition (B) occurs.
• Logged readings memory becomes full.
• You change the rotary switch position.
4-2
4-3
4-4
4-5
4-6
5-1
000.0 °C Temperature ( w ) Temperature 000.0 ° to ±999.9 ° - Use q to increment 000.0 °C (or °F)
or selected. offset adjust or decrement digit.
000.0 °F
Use < > to select digit. Selected digit
flashes.
dbrEF AC volts (\ or dB type dBm or dBV (m or V flashing) - Use < > dBV
,) selected. to select.
5-2
8888 Display digits 8888 (4) or 88888 (5) Use < > to select. 88888
bLoFF Backlight time out MM:SS - Use q to increment or decrement minute or 15:00
second values.
Use < > to select minutes or seconds. Selected values
flash. Setting value to 00:00 disables timeout.
Pr0FF Power off time out HH:MM - Use q to increment or decrement hour or minute 00:15
values.
Fcty Restore factory defaults yE5 or no (flashing) - Use < > to select. no
5-3
Select and edit setup options as follows: Adjusting the Temperature Offset
• Turn the rotary switch to a measurement function: If the meter is in a temperature measurement function,
use the following procedure to set an offset for your
• Press O T to advance to the next setup option temperature probe:
and save the present selection.
1. Turn the rotary switch to temperature ( w).
• Press [ to increase or ] to decrease a value.
2. Connect the temperature probe and probe adapter to
• Press T (l) to go back to the previous digit or
selection.
the& and V inputs on the meter.
5-4
5-5
1. Press O, then T until 8888 (for 3-1/2 digits) or 4. When you have set the digits as desired, press
88888 (for 4-1/2 digits) appears in the display. OT to save the settings and proceed to the next
setup selection.
2. To change the selection, press T (l) or % ( s).
5-6
Hours and minutes to a maximum of 23:59 can be set. 5. Press O T to store the selection and proceed to
the next selection.
Note
If the reading occurs within 1 hour of the start of
Setting the Line (Main) Frequency
the operation, the elapsed time clock is used. Although the meter operates on battery power only, it is
The meter also uses elapsed time for all average important to specify the frequency (50 or 60 Hz) of the line
readings. Elapsed time is expressed in minutes (main) power. This allows the meter to filter out related
and seconds to a maximum of 59:59. noise.
To change the 24-hour clock: To change the line (main) frequency:
1. Press O T until Hour appears in the display and 1. Press O T until 50-60 appears in the display.
the hour digits in the lower right corner of the display
begin flashing. 2. Press T or % to change the selection to the correct
frequency.
2. Press [ or ] to increase or decrease the
hour value. 3. Press O T to store the selection and proceed to
the next selection.
5-7
If you select yE5, all setup options revert to the Selections that were previously saved with O T are
factory defaults; you cannot specify individual retained.
choices.
5-8
Introduction 3. Soak a new swab with alcohol. Work the swab around
in each terminal.
This chapter describes basic operator maintenance. For
calibration and performance test information, order the 87 Testing the Fuses
& 89 Series IV Service Manual, PN 676137.
Before measuring current, test the appropriate fuse as
General Maintenance shown in Figure 6-1. If the tests give readings other than
those shown, have the meter serviced.
Periodically wipe the case with a damp cloth and mild
detergent. Do not use abrasives or solvents. WWarning
Dirt or moisture in the terminals can affect readings and To avoid electrical shock or personal injury,
can falsely activate the Input Alert feature. Clean the remove the test leads and any input signals
terminals as follows: before replacing the battery or fuses. To
prevent damage or injury, install ONLY
1. Turn the meter off and remove all test leads. specified replacement fuses with the
amperage, voltage, and speed ratings shown
2. Shake out any dirt that may be in the terminals. in Chapter 7.
6-1
89 89
LOG LOG
GING GING
MUL MUL
TIMET TIMET
ER ER
AutoH AutoH
OL OLD
D HOLD
HOLD FAST FAST
MN MN
MX MIN MX
MIN MAX
MAX LOGG LOGG
ING ING
CANC REL CANC REL
EL EL YES
Hz % YES Hz %
SETU ms SETU ms SAVE
P SAVE P
RAN RAN
GE GE
nS NO nS NO
ac+d ac+d
c mV c mV
ac+d ac+d
c V c V
dB mV C F
dB mV C F
A A
dB V mA dB V mA
OFF A OFF A
A A
mA mA
A
ac+d
c A A
ac+d
c
A
A
mA
VIE
CLEA
RM
W
EM
ac+d
c
mA A
mA
VIE
CLEA
RM
W
EM
ac+d
c
mA
10A A 10A A
FUSEMAX FUSEMAX TEMP
D CO TEMP D CO ERAT
M ERAT
URE
M URE
400m 400m
FUSE A FUSE A
D V D V
CA CA
1000T 1000T
V V
tc038f.eps
Figure 6-1. Testing the Current Fuses
6-2
6-3
F2
F1
tc037f.eps
Figure 6-2. Battery and Fuse Replacement
6-4
3. Remove either fuse by gently prying one end loose, 4. If the meter still does not work, pack it securely and
then sliding the fuse out of its bracket. forward it, postage paid, to the location provided by
the appropriate Fluke contact. Include a description of
4. Install ONLY specified replacement fuses with the the problem. Fluke assumes no responsibility for
amperage, voltage, and speed ratings shown in damage in transit.
Chapter 7.
A meter under warranty will be repaired or replaced (at
5. Reinstall the battery door. Secure the door by turning Fluke’s option) and returned at no charge. See the
the screws one-quarter turn clockwise. registration card for warranty terms.
6-5
Reference Part
Description Designators Number Qty
Battery, 1.5 V, 0-15 mA, AA Alkaline H8, H9, H10, H11 376756 4
6-6
7-1
Physical Specifications
Display (LCD) Digital: 50000/5000 counts primary display,
5000 counts secondary display;
updates 4/second.
Analog: 51 segments, updates 40/second.
Operating Temperature − 20 °C to + 55 °C
Storage Temperature − 40 °C to +60 °C
Temperature Coefficient 0.05 x (specified accuracy) / °C (<18 °C or >28 °C)
Relative Humidity 0 % to 90 % (0 °C to 28 °C)
0 % to 70 % (28 °C to 55 °C)
Altitude Operating: 0-2000 meters per EN61010 CAT III, 1000V
0-3000 meters per EN61010 CAT II, 1000V, EN61010 CAT III, 600V
Storage: 10000 meters
Battery Type 4 AA Alkaline, NEDA 15A or LR6
Battery Life 72 Hours typical (with backlight off)
Shock Vibration Per MIL-T-PRF 28800 for Class II instruments
Electromagnetic Compatibility Susceptibility and Emissions: Commercial Limits per EN61326-1 (see notes for DC
(EMC) mV, DC µA, and Resistance.)
Size 10.0 cm x 20.3 cm x 5.0 cm (3.94 in x 8.00 in x 1.97 in)
(Not Including Accessory Mount)
Weight 545 grams (1.2 lbs.)
Case Sealing IP-42 per IEC 529, Section 3
Warranty Lifetime
Calibration Interval 1 year
7-2
7-3
Basic Specifications
Function Ranges/Description
DC Voltage 0 to 1000 V
AC Voltage, true RMS 15 mV to 1000 V – 100 kHz bandwidth
Basic Accuracy DC voltage: 0.025 %
AC voltage: 0.4 %
DC Current 0 to 10 A (20 A for 30 seconds)
AC Current, true RMS 25 µA to 10 A (20 A for 30 seconds)
Resistance 0 to 30 MΩ
Conductance 0 to 50 nS
Capacitance 0.001 nF to 50 mF
Diode Test 3.1 V
Temperature −200 °C to 1350 °C (−328 °F to 2462 °F)
Frequency 0.5 Hz to 1000 kHz
LOGGING Intervals At least 288 intervals may be stored. Up to 700 unstable event values (see AutoHold)
(Model 89 only) are automatically added to LOGGING memory for viewing only through optional PC
software. Additional intervals will be logged up to 988 if the signal is stable.
SAVE Readings Up to 100 readings may be saved by the user in a memory separate from LOGGING
(Model 89 only) memory. These readings may be viewed using VIEW MEM.
7-4
7-5
Accuracy
Function Range Resolution 45-1 kHz 20-45 Hz 1-20 kHz 20 kHz-100 kHz
7-6
7-7
500.00 Ω 0.01 Ω
1 3,4
Resistance 0.05 % + 10
5.0000 MΩ 0.0001 MΩ
2
0.15 % + 4
30.000 MΩ 0.001 MΩ
2
1%+4
7-8
11.00 nF 0.01 nF
110.0 nF 0.1 nF
1.100 µF 0.001 µF
110.0 uF 0.1 µF
1,100 µF 1 µF
3
11.0 mF 0.01 mF
3
50.00 mF 0.10 mF 1% + 50
1
Diode Test 3.1000 V 0.0001 V 2%+2
1. For the 5,000 count mode, divide the number of least significant digits (counts) by 10.
2. For film capacitor or better, using Relative mode (REL ∆) to zero residual on 1.1 nF range.
3. The small range annunciator above the AUTO/MANUAL messages will show 50, and the display will show xx.xx throughout these two
measurement ranges.
7-9
MIN MAX AVG Response: 100 ms to 80 % Specified accuracy ± 12 counts for changes > 200 ms
in duration. (± 40 counts in AC for changes > 350 ms
and inputs > 25 % of range)
FAST MN MX 250 µs Specified accuracy ±100 counts for changes >250 µs in
5
duration
1. Reading will be 0.00 for signals below 0.5 Hz.
2. Duty cycle and pulse width operate on repetitive waveforms at 14.5 Hz or greater.
3. Accuracy specification is relative to the user-adjustable temperature offset, and assumes ambient temperature stable to ± 1 °C.
4. For ambient temperature changes of ± 5 °C, rated accuracy applies after 1 hour.
5. For repetitive peaks; 2.5 ms for single events.
7-10
7-11
Input Characteristics
Function Input Impedance (Nominal)
AC Volts, mV > 90 dB dc to 60 Hz
Full-Scale Voltage
500 Ω 5 kΩ 50 kΩ 500 kΩ 5 MΩ 30 MΩ
7-12