Professional Documents
Culture Documents
Maintenance Manual
MM-INFRANEO-EN Ind. 0 - 12/2012
IMPORTANT
The technical elements that constitute this manual (text and illustrations) are not contractual,
their only target being to bring assistance for troubleshooting and repairing the INFRANEO.
Use, duplication or disclosure of subject data, for any purpose other than relating to the
servicing or repair of the equipment, is strictly prohibited without the written authorisation of
CHOPIN Technologies.
Maintenance manual
3
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Table of contents
1. Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Chapter 2 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1. Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2. Fault handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
4. Functioning diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Chapter 3 Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
2. Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
1. Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
2. Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Maintenance manual
5
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Maintenance manual
6
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
This chapter summarizes most of the important instructions relating to operation and maintenance of the
INFRANEO
In addition, this section contains further information solely intended for people entitled to carry out
maintenance and repair operations on this unit.
A B
■ Connection
4 USB ports are available on the front of the device for USB periph-
erals connection: keyboard, mouse, modem or mass storage
peripheral (key, hard drive).
Although this equipment makes little use of this feature, other appa-
ratuses can be connected.
C D
❏ Electrical connection
The connection to the inverter shall be made using the cable sup-
plied with the INFRANEO. The connector socket is located at the
back of the device.
■ Fuse
■ Environment
❏ Indoor use
❏ Hygrometry: HR 85%
2. Precautions related ■ The test management with the INFRANEO requires constant
care.
to tests
All necessary instructions (test conditions, handling, cleaning) are
detailed inside the Instruction Manual, and must be respected scru-
pulously; failure to do so could lead to:
❏ erroneous results,
■ Systematically check at the beginning of each test that the cell sli-
ding action in its compartment is good.
■ Cleaning
If the device doesn't start and after mains supply monitoring, check
the fuses of the INFRANEO.
❏ The fuses are located at the back of the device behind a cover.
❏ Unplug the device, use a small screwdriver to open the fuse hol-
der, and replace the defective fuse(s).
❏ The green USB memory stick enables software data and test run
storage. It is recommended to perform this storage on a regular
basis, in order to prevent any loss or damage of data and previous
results.
■ TeamViewer Process
■ Lamp(NEOBS50/ES) replacement
The characteristics of the lamp are checked at each self-test. If the
message below appears, proceed to the lamp replacement, ref
NEOBS50/ES (see op. 5-2 p.87).
Chapter 2 TROUBLESHOOTING
Maintenance manual
15
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Maintenance manual
16
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Chapter 2. Troubleshooting
The aim of this chapter is, in case a fault appears, to find the probable origin and to isolate any failed compo-
nent or sub-assembly; the required actions are then detailed.
For any CHOPIN Technologies customer service inquiry, mention the serial number of the equipment.
If this fails, the unit will have to be sent back to CHOPIN for in-work-
shop troubleshooting and repair.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 17
Infraneo
2. Fault handling As a general rule, if a failure appears, restart the unit to confirm
the failure.
A Equipment/Software
The INFRANEO does not The INFRANEO does not start Refer to fault handling 3.1
start
The mini PC does not start The PC locks up at initialization Refer to fault handling 3.2
The application does not - The application does not start Refer to fault handling 3.3
start
- The manual activation of the
application fails
Touchscreen problem The PC works (three tones at Refer to fault handling 3.4
startup) but nothing appears on
screen
Lamp aging The lamp lighting doesn’t provide ■ Replace the lamp Refer to
the same intensity anymore Ch 3
■ Contact the CHOPIN Operation
Technologies customer ser- 5-2
vice
Maintenance manual
18 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
B Error messages
Refer to
N° ERR Display / Description Action
Chap.3 §
Err - 101 Insufficient energy for this spectrum Refer to fault handling 3.5
Err - 102 Emptying trap closure problem Refer to fault handling 3.6
Err - 103 No grain, measurement impossible Refer to fault handling 3.7
Err - 105
Err - 104 Too low energy on blank spectrum Refer to fault handling 3.8
Err - 106 Filling problem Refer to fault handling 3.9
Err - 107 Order zero: too low energy Refer to fault handling 3.10
Err - 108 Order zero: peak not detected
Err - 109 No drawer Refer to fault handling 3.11
Err - 110 Sliding cell position problem Refer to fault handling 3.12
Err - 111 Error when reading the SW module or Refer to fault handling 3.13
Err - 121 the moisture tester
Err - 112 Sliding cell extracted ■ Re-insert the sliding cell Refer to
Ch 3
■ Check setting of the C7 position Operation
7-1
Err - 113 Bad sliding cell position ■ In the INFRANEO application, select the Refer to
product to use again Ch 3
Operation
■ Check the sliding cell positions 7-1
Err - 114 Measurement impossible (initialisation ■ Restart Infraneo
fault)
■ Contact the CHOPIN Technologies cus-
tomer service
Err - 115 Measurement impossible - INFRANEO ■ Reset the INFRANEO
busy
■ Contact the CHOPIN Technologies cus-
tomer service
Err - 116 Not active in flour mode ■ The selected function is not active in
flour mode. To reactivate the function,
select a "Grain" product
Err - 117 Flour reference test not performed ■ Click on the "Ref. flour" before perfor-
ming a measurement
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 19
Infraneo
Refer to
N° ERR Display / Description Action
Chap.3 §
Maintenance manual
20 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
C Other failures
Instability of results Fluctuating result for a same sample Refer to fault handling 3.16
type
Outliers results Outliers results of a product Refer to fault handling 3.17
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 21
Infraneo
3. Fault handling
instructions
The INFRANEO
does not start
YES NO
3 tones at startup?
End
End
Maintenance manual
22 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.2 The mini PC does not start
Mini PC startup
problem
End
End
End
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 23
Infraneo
3.3 The application does not
start
The application
does not start
End
Maintenance manual
24 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.4 Touchscreen problem Blurring screen
Black out screen
End
Check the touch pad supply voltage on
the lamp supply board (11.5 Vdc)
YES NO
Voltage correct ?
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 25
Infraneo
3.5 Err - 101 Insufficient energy for this spectrum
Err - 101
End
YES NO
OZ correct ?
Err - 107
Err - 108
see 3.10
p.31
YES Does the problem NO
remain?
Maintenance manual
26 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.6 Err - 102 Emptying trap closure problem
Err - 102
Check: END
- Adjustment of the closed trap position
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 27
Infraneo
3.7 Err - 103 Err - 105 No grain, measurement impossible
Err – 103
Err – 105
End
Check vaned rotor for proper rotation
ERR - 106
Check emptying trap is properly close
OUI
and the sliding cell is at its place
see op. 7-1
p.95
End
Restart the INFRANEO and run a new
complete OZ
YES NO
OZ correct ?
Err - 107
Perform a test again Err - 108
see 3.10
YES Does the problem NO p.31
remain?
Maintenance manual
28 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.8 Err - 104 Too low energy on blank spectrum
Err - 104
End
YES NO
OZ correct ?
Err - 107
Err - 108
see 3.10
p.31
YES Does the problem NO
remain?
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 29
Infraneo
3.9 Err - 106 Filling problem
Err - 106
Maintenance manual
30 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.10 Err - 107 Err - 108 Order zero: too low energy
Order zero: peak not detected
Err - 107
Err - 108
End
A
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 31
Infraneo
A - Sliding cell order zero position problem
YES NO
Is the light ray present?
End End
End End
Maintenance manual
32 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
B - Lamp supply problem
NO YES
Voltage correct?
YES NO
Voltage correct?
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 33
Infraneo
3.11 Err - 109 No drawer
Err - 109
YES NO
Does the problem remain?
YES NO
Does the problem remain?
YES NO
Does the problem remain?
Maintenance manual
34 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.12 Err - 110 Sliding cell position problem
Err - 110
End
Check the motor position. If the motor is on Check the carriage motor connection
mechanical stop, adjust the position and replace the motor if needed
End End
Remove the sliding cell and the Replace the CPU board
carriage, then find the reason for the
hard point (too important tightening of
the sliding cell support, sliding cell
deformed…)
see op. 4-1
p.84
see op. 3-9
p.82
YES Does the problem NO
remain?
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 35
Infraneo
3.13 Err - 111 Err - 121 Error when reading the SW module or the moisture tester
Moisture tester/SW module not present (no detection of the
apparatus)
Err - 111
Refer to maintenance
manual of the SW End
module or the
moisture tester
Test the serial link of the module (direct Check module supply voltage(11.5 Vdc)
connection) on the DIN connector
Maintenance manual
36 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.14 Err - 122 Dibromo spectrum not recognized
Err - 122
End
End
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 37
Infraneo
3.15 Err - 301 The application does not communicate with the INFRANEO
Err - 301
Maintenance manual
38 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3.16 Instability of results
Instability of
results
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 39
Infraneo
3.17 Outliers results
Outliers results
see user
manual
YES Does the problem NO
remain?
see user
manual
YES Does the problem NO
remain?
see user
manual YES NO
Value correct?
Reinstall the calibration corresponding Check that the sliding cell is empty
with product(s)/parameter(s) relevant to (neither Neocup nor obstructed glass)
outliers if necessary and is still in position (foam at the back
of the INFRANEO magnet lock)
Remedy if necessary
Maintenance manual
40 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
4. Functioning diagram The diagrams below can be used as "reminder" of failure localisa-
tion.
Equipped hopper
Touch screen
Optical
bench
Sliding cell
motor
Emptying trap
motor
Optical bench
board
Drawer
Lamp
Mini PC supply
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 2 Troubleshooting 41
Infraneo
Legend:
C1: network optical fork
TFT board M1: network motor
C2: optical sensor filter wheel
M2: filter wheel motor
USB hub
Mini PC RJ45 connectors
Reset
Mini PC ethernet
link
CPU supply
24 Vdc Cabled mains
plug
CPU board 230 Vac 230 Vac
230
I2C link Vac
Lamp supply
M M M
Hooper Trap Sliding
cell 12 Vdc
Magnet
OB board lock
Relay with cabled capacitor
Mini PC fan
C2 C1
M2 M1
Lamp
Optical bench
Interconnection diagram
Maintenance manual
42 Chapter 2 Troubleshooting MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Chapter 3 REPAIR
Maintenance manual
43
MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Maintenance manual
44
MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Chapter 3. Repair
This chapter describes all the corrective maintenance operations authorised by CHOPIN Technologies, which
can be carried out on the INFRANEO (some of these instructions are, in particular, taken from chapter 2
"Troubleshooting").
Spare parts and sub-assemblies shall be selected from the illustrated parts lists of chapter 4 "Spare parts".
For all operations required to open The power can be switched back ON only once the unit is
the INFRANEO, you must first closed, and all internal parts have been re-installed and re-con-
switch the power OFF, mains cable nected.
disconnected.
Note: An exception should be made for some checks and controls
(supply voltage measurement in particular) as long as all safety pre-
cautions have been taken.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 45
Infraneo
1.2 List of instructions
1: Basic operations
Operation 1-1 Removing/Installing the MEC
cover on the bottom plate
Operation 1-2 Removing/Installing the MEC
covers on the optical bench
Operation 1-3 Removing/Installing the MEC
covers on the sliding cell
compartment
Operation 1-4 Removing/Installing the CABL
covers on the power supply
box
2: Power supply box
Operation 2-1 Removing/Installing cabled MEC
mains plug
Operation 2-2 Removing/Installing the mini MEC
PC power supply
Operation 2-3 Removing/Installing the CABL
lamp supply board
Operation 2-4 Removing/Installing relays TECH
with cabled capacitor
Operation 2-5 Removing/Installing the TECH
CPU board supply
3: Sliding cell compartment
Operation 3-1 Removing/Installing the CABL
sliding cell motor
Operation 3-2 Removing/Installing the TECH
emptying trap motor
Operation 3-3 Removing/Installing the TECH
Equipped Hopper
Maintenance manual
46 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 47
Infraneo
Maintenance manual
48 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
1.3 Operation localisation
6 :Bottom plate
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 49
Infraneo
Maintenance manual
50 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 51
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Tip over the device in its upright position, making sure that it is
stable (A).
A B
3. Unscrew the two fastening screws on the front (C), the bottom
seal screw and the top legs (D), by securing the unit to the
chassis.
C D
Maintenance manual
52 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Installing
- make sure that the cables are correctly positioned (no pressure,
no tension, no jamming, etc.),
- make sure that the legs are correctly positioned and screwed on,
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 53
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Cut the seal located at the back of the equipment (A) and the
seal one located beneath it (B).
A B
Maintenance manual
54 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
4. Unscrew the two fastening screws and the seal screw at the
back (C). Gently pull the cover out toward the outside to free it
from the locking groove (D).
C D
5. Lift the cover toward the front of the device and hold it in its
upright position. Do not exert any excessive force on cables.
E F
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 55
Infraneo
Consumables: -
Specific tools: -
■ Installing
When installing the cover on the optical bench and the left-hand
plate:
Maintenance manual
56 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Removing
3. Disconnect the earthing wire from the cover (A) as well as the
connector from the diode and button on the front (B).
A B
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 57
Infraneo
Consumables: -
Specific tools: -
4. You can now remove the cover on the sliding cell compartment
(C). Put to one side the washers (D).
C D
■ Installing
When installing the cover on the sliding cell compartment and the
right-hand plate:
Maintenance manual
58 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Removing
2. Remove the cover from the power supply box by gently pulling
it out toward the outside (B).
A B
■ Installing
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 59
Infraneo
Consumables: -
Special tools: -
■ Removing
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
A B
Maintenance manual
60 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
■ Installing
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 61
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Remove the cover on the power supply box (see op. 1-4).
A B
Maintenance manual
62 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Installing
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 63
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Remove the cover on the power supply box (see op. 1-4).
A B
4. Tip over the device in its upright position and remove the cover
on the bottom plate (see op. 1-1). Take care not to jam the
cables.
5. Then tip over the device on its right-hand side. Take care not
to exert any excessive force on the cables (C).
C D
Maintenance manual
64 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
10. Remove the power supply by extracting its cable through the
slot located between the power supply box and the bottom
plate (H).
E F
G H
■ Installing
- ensure that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
- check that the reset block is properly aligned with the reset button
of the mini PC,
- check proper positioning of the power supply and its cable in the
support,
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 65
Infraneo
Consumables: -
■ Removing
C D
Maintenance manual
66 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
■ Installing
9. Electrically insulate the board from the other power supply box
components so as to make the potentiometer accessible with
a screwdriver, without risk of external contact (E).
E F
12. Once this setting has been obtained, disconnect the device
power supply.
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 67
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Remove the cover on the power supply box (see op. 1-4).
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
68 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Removing
1. Remove the cover on the power supply box (see op. 1-4).
3. Remove the power supply support and the lamp supply board
(see op. 2-3).
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 69
Infraneo
Consumables: -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment(see op. 1-3).
2. Unscrew the arm locking screw (A).
B C
Maintenance manual
70 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
- match up the arm axis fastening reference with the motor shaft,
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 71
Infraneo
Consumables: -
Special tools: -
■ Removal
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
A B
C D
Maintenance manual
72 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
E
A
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
- match up the arm axis fastening reference with the motor shaft,
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 73
Infraneo
Consumables: -
Special tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
■ Installing
Maintenance manual
74 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
2. Unscrew the two screws and nuts on the motor (A) and its sup-
port on the equipped hopper, followed by the screw clamping
the motor axis (B).
A B
3. Unscrew the four fastening screws (C) between the motor and
its support.
C
■ Installing
- place Bloc Jelt on the screw clamping the coupling to the motor
shaft,
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 75
Infraneo
Special tools: -
■ Removing
2. Unscrew the two screws and nuts on the motor (A) and its sup-
port on the equipped hopper, followed by the screw clamping
the motor axis (B).
A B
3. Loosen the clamping nut (C) to free the sensor and extract it
(D).
C D
■ Installing
To install the sensor, position the blue part of the sensor 0.8 mm
from the positioning wheel, then bring up the (red) nut until it bears
on the (green) motor support. Then lock the fastener in place by
retightening the (purple) nut. Place Bloc Jelt on it.
Maintenance manual
76 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 77
Infraneo
Consumables: -
Special tools: -
■ Removing
2. Unscrew the two screws and nuts on motor (A) and on its
equipped hopper support.
3. Unscrew the two screws (B) on the vaned rotor to free the
shaft (C).
B DC
■ Installing
Maintenance manual
78 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
Ensure that the new detector mirror does not come into
contact with dust or objects (this could result in shocks,
scratches, etc.).
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
2. Disconnect the box electrical connection on the CPU board
(A).
3. Remove the cable grommet from its notch (B).
4. Unscrew the 4 screws fastening the box to the sliding cell com-
partment (C).
5. Remove the box (D).
A B
C D
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 79
Infraneo
Consumables: -
Specific tools: -
■ Installing
Maintenance manual
80 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
Ensure that the new detector mirror does not come into
contact with dust or objects (this could result in shocks,
scratches, etc.)
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3). Remove drawer (A).
2. Remove the cover from the CPU board box (see op. 1-5) (B).
A B
4. Remove the tightening nut (D) and extract the sensor by slid-
ing it in its housing through the inside of the box.
C D
■ Installing
To install the sensor, position its blue part 1 mm from the drawer
magnet in the stored position, then lock the tightening nut.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 81
Infraneo
Special tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
2. Remove the cover on the CPU board box (see op. 1-5).
3. Remove the equipped hopper (see op. 1-3)
4. Uncouple the motorisation arm from the sliding cell (see op. 3-
1)
5. Disconnect the electrical connection on the CPU board side
from the sliding cell presence sensor (see op. 4-1)
6. Unscrew the two screws on the trap motor support (A) and
withdraw it.
A B
10. Remove the motorisation arm + sliding cell assembly from the
sliding cell compartment (C and D).
C D
Maintenance manual
82 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Special tools: -
■ Installing
- check the insertion direction and proper sliding of the sliding cell in
the compartment,
- check that the sample holder fastening rods are properly screwed
onto the base. Lock them in place using Loctite 496 if required (M),
- check the proper positioning of the foam seal placed between the
chassis and the compartment (N),
M N
- check that the cables are properly positioned (no pressure, ten-
sion, blocking, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 83
Infraneo
Consumables -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate, the cover on the sliding cell com-
partment and the CPU board box cover (see op. 1-5).
2. Be sure to identify the connectors and then disconnect them
using a clamp.
Maintenance manual
84 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 85
Infraneo
Consumables: -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
86 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Removing
A B
■ Installing
Avoid all friction and contact of the lamp bulb with the
components and, in particular, the inside of the support.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 87
Infraneo
Operation 5-3 Removing/Installing the VGA Interface Board and the touch pad controller
Consumables: -
Specific tools: -
The touch pad Controller (1) and the VGA (2) Interface Board can
be replaced separately.
■ Removing
1. Remove the cover from the optical bench (see op. 1-2).
2
2. Take care to identify the connectors. Use a clamp to discon-
nect them.
Maintenance manual
88 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
4.
5 : Optical bench compartment Sheet: 2 / 2
Operation 5-3 Removing/Installing the VGA Interface Board and the touch pad control-
ler
Consumables: -
Specific tools: -
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 89
Infraneo
Consumables: -
Specific tools: -
■ Removing
■ Installing
Maintenance manual
90 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
A B
4. Remove the fan by passing the supply cord under the reset
block. Remove the reset block if necessary (see op. 2-2).
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 91
Infraneo
Consumables: -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
A Power supply
A
B Touch screen
C CPU board
B
D Ethernet hub
E USB hub port
C
F Touch pad USB port
D
E
F
Electronic circuits sensitive to elec-
trostatic discharges!
When handling, take the usual pre- 4. Swivel the block on one of the side edges in order to access
cautions: the fastening screws placed beneath.
conductive floor, earthed wrist
band.
Maintenance manual
92 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Specific tools: -
■ Installing
- check that the cables are properly positioned (no pressure, ten-
sion, jamming, etc.),
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 93
Infraneo
Consumables: -
Specific tools: -
■ Removing
Any cover removal requires disconnection of the device power
supply.
■ Installing
- avoid shocks,
Maintenance manual
94 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Enter Exit
Select posi-
tions
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 95
Infraneo
Consumables: -
■ INFRANEO adjustments
❏ Adjusting position C4
1. Insert the "universal" (or "technical") sliding cell.
2. In the "Cell position test" section, press button "C4" to posi-
tion the cell.
3. Use arrows (in) and (out) in the scroll bar to bring up the
sliding cell with the face of its first rib slightly protruding (no more
than 1 mm) from the outer face of the sample holder, so as to
facilitate the insertion of accessories. (See the figure below).
Reference face
Maintenance manual
96 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
❏ Adjusting position C7
10. In the "Cell position test" section, press button "C4", then
the "magnet lock" key, and remove the sliding cell.
11. Use arrow on the scroll bar to reach the maximum "energy"
level (see the figure below).
Energy
12. In the "Update" section, press button "C7" to save the new
position.
14. Press the "Quit" button at the bottom of the window. The mes-
sage "You are about to switch off the system, are you sure?"
appears. Click "OK" and restart the application.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 97
Infraneo
Consumables: -
Special tools: -
Mechanical adjustments
Position T1 Adjust-
ment bar
Saving the po-
sition
Save
Position T1
Maintenance manual
98 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
■ Closed position
B C
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 99
Infraneo
Consumables: -
Maintenance manual
100 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
However, if the test was not successful, try again. Should the prob-
lem persist, contact the After Sales Service.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 101
Infraneo
Special tools: -
A B C D E F G
Maintenance manual
102 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Special tools: -
A B
Remove the excess grease on the motor axis and the wheel.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 103
Infraneo
Consumables:
11.5 Vdc
To check that the lamp works, reconnect the cable and extract the
lamp as explained above.
Maintenance manual
104 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Contact connector
8: +24 V sliding cell magnet lock (red)
7: 0 V sliding cell magnet lock (black)
6: NC
5: ON/OFF button (black)
4: NC
3: earth (brown)
2: drawer contactr (grey)
1: NC
Led connector
3: Red led anode (Orange)
2: green led anode (Red) CPU / PC panel link
1: earth (White)
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 105
Infraneo
Consumables: -
Fork connector 1
5: 0 V (green)
4: NC
3: return (white)
2: LED control (black)
1: + 5 V LED supply (red)
OB board/CPU
board link Motor connector 1
6: Brown
Network motor moni- 5: Blue
toring LED 4: Yellow
3: Red
2: White
1: Brown
Fork connector 2
5: 0 V (black)
4: NC
3: return (yellow)
2: LED control (black)
1: + 5 V LED supply (red)
Filter wheel
monitoring Led Motor connector 2
6: NC
5: Brown
4: Red
3: Brown
2: Red
1: NC
Maintenance manual
106 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
0V
230 Vac
24 Vdc
230 Vac
11.5 Vdc control
0 Vdc control
15 Vdc
0 Vdc
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 107
Infraneo
Consumables: -
Special tools: -
Hard disk Screen HDD supply cord Actions to perform Stick to use CHOPIN
ref.
SATA 12’ panel Red Restore Windows Blue sticker MIC 108
■ PRELIMINARY STEP
1. Switch on the INFRANEO.
2. Access the BIOS by following the instructions given at the bot-
tom of the screen during start-up (DEL or SUPPR key). If you
are asked to do so, type in the password "biosguard".
3. Access the function "Advanced BIOS features".
4. In the function "First Boot Device", select "USB HDD".
5. Save changes (Choose F10 then F10 and finally "Y").
6. Wait for Windows to be completely launched and switch off the
INFRANEO.
■ RESTORING WINDOWS:
1. Insert the USB stick corresponding to your screen/hard disk,
into one of the accessible USB ports.
2. Switch on the Infraneo.
3. Wait for all the files to load.
Maintenance manual
108 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
A B
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 109
Infraneo
Consumables: -
Special tools: -
IDE 12’ panel Grey Restore Windows Orange sticker MIC 130
15’ panel Grey Update the Windows resto- Purple sticker MIC 107
ration BIOS Orange sticker MIC 130
SATA 12’ panel Red Restore Windows Blue sticker MIC 108
INEOS 600 12’ Red Restore Windows Yellow sticker MIC 109
screen
■ PRELIMINARY STEP
1. Switch on the Infraneo.
2. Access the BIOS by following the instructions given at the bot-
tom of the screen during start-up (DEL or SUPPR key). If you
are asked to do so, type in the password "biosguard".
3. Access the function "Advanced BIOS features".
4. In the function "First Boot Device", select "USB HDD".
5. Save changes (Choose F10 then F10 and finally "Y").
6. Wait for Windows to be completely launched and switch off the
Infraneo.
1. Insert the USB stick with the orange sticker into one of the
accessible USB ports.
Compulsory before system
restoration: 2. Switch on the Infraneo.
This update only applies to IDE 15’
panel hard disks. 3. An "Update BIOS" window appears. Select 1 and validate.
4. Please wait while the BIOS is updated. The system will auto-
matically reboot.
During the reboot, remove the USB stick.
Maintenance manual
110 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Consumables: -
Special tools: -
■ RESTORING WINDOWS:
1. Insert the USB stick corresponding to your screen/hard disk
into one of the accessible USB ports.
2. Switch on the Infraneo.
3. Wait for all the files to load.
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 111
Infraneo
Consumables: -
Special tools: -
A B
10. Finally click on "OK" to validate. The system will reboot auto-
matically. During the reboot, remove the USB stick provided to
restore Windows.
Maintenance manual
112 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Special tools: -
■ Removal
Any cover removal requires disconnection of the device power
supply.
1. Remove the right-hand plate and the cover on the sliding cell
compartment (see op. 1-3).
2. Unscrew the arm locking screw (A). Apply a lever if necessary
using a tool with a flat thin end to separate the shaft + arm
assembly (B).
A B
3. Separate the drive rod arm from the sliding cell by inserting a 7
open end wrench between them (C). Withdraw the sliding cell
from the sample holder.
4. Separate the sliding cell drive rod from the sample holder car-
riage (D).
C D
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 09/2012 Chapter 3 Repair 113
Infraneo
Consumables: -
Special tools: -
■ Installing
Maintenance manual
114 Chapter 3 Repair MM-INFRANEO-EN Ind. 0 - 09/2012
Infraneo
Maintenance manual
115
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Maintenance manual
116
MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
1. Important ■ The illustrated parts lists in this chapter contain the information
necessary for purchasing spare parts and spare sub-assemblies
only.
The lists also include the detailed description of all fasteners that
may need to be replaced, if damaged or lost, when replacing these
spare units.
❏ the necessary quantity (make sure to take into account the mini-
mum quantity per order).
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 117
Infraneo
Maintenance manual
118 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
3. Parts lists
Désignation Figure N°
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 119
Infraneo
figure 1 - Grouping list and options
1
11
12
2
13
5
14
6
3
C
6
C
7
2
C
5
C
1
C
9 15
10
16
Maintenance manual
120 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN Part
item Description Qty qty p. Note
no.
order
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 121
Infraneo
figure 2 - Power supply unit equipped
5
13
12
11
10
8
6
Maintenance manual
122 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
13 LOCKNUT, H M5 ZINC-PLATED 1
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 123
Infraneo
figure 3 - Optical bench equipped
1
2 3
6 5 4
Maintenance manual
124 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 125
Infraneo
figure 4 - Sliding cell and hopper compartment
7
8
Maintenance manual
126 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
1 NUT, HU M4 AZ 2
2 WASHER, DE 3 AZ 2
8 SCREW, CS M3x25 I 4
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 127
Infraneo
figure 5 - Hopper equipped
Maintenance manual
128 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Hopper equipped
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
1 NUT M4 2
2 WASHER, FLAT M4 2
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 129
Infraneo
figure 6 - Bottom plate equipped
Maintenance manual
130 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 131
Infraneo
figure 7 - Screen assembly equipped
Maintenance manual
132 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012
Infraneo
Min.
CHOPIN
item Description Qty qty p. Note
Part no.
order
Maintenance manual
MM-INFRANEO-EN Ind. 0 - 12/2012 Chapter 4 Spare parts 133
Infraneo
Maintenance manual
134 Chapter 4 Spare parts MM-INFRANEO-EN Ind. 0 - 12/2012