Professional Documents
Culture Documents
50
16
8
Its smooth perforated surface allows the air to flow and the liquids to
drain away.
It is the ideal belt for production food processes (boiling, draining, drying)
as well as for preservation processes (sterilization, refrigeration).
Pitch 50 mm
Open area 20 %
Thickness 16 mm
Colours: [W] White - [G] Grey - [B] Blue - [N] Natural - [O] Black. // The materials and colours that are normally in stock are those above indicated. In special cases in
which it is needed a belt in a material or colour different from those above mentioned, you should ask directly to EUROBELT.
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
SERIES / B50
ACCESSORIES [SPROCKETS]
Drive
direction
Bore 40
6 100.00 40 1.5" 40
8 130.65 40 1.5" 40
40 1.5" Polypropylene
10 161.80 40
60 2.5"
Polyacetal
40 1.5"
12 193.18 40
60 2.5"
Stainless steel
40 1.5"
16 256.29 60 2.5" 40
90 3.5"
W IT H K E Y WAY W IT H O U T K E Y WAY
We have plastic sprockets for round shaft with and without keyway. We also have sprockets to be used with motor drum in applications
needing a special cleaning or in conveyors in which it is not possible to place the motor in the outside due to problems of space or safety.
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
B50 / SERIES
INSTALLATION
Bore for
Screws
square shaft
40 M6x6
60 M6x6
90 M6x6
C EN T R A L S PRO C K E T
Sentido
deDrive
marcha
direction
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
ACCESSORIES [FASTENING RING CLU]
High-resistance ACETAL.
A N I L LO D E R E T EN CI Ó N C LU
The drive system of modular belts requires the central sprocket not to move axially both in the drive and the
idle shafts.
The rest of sprockets can slide freely on the shaft adapting to the possible changes of the belt, so that the
correct position of the teeth is guaranteed.
Central Sprocket
1.Direct installation without 2.Easy placing on the shaft by 3.Reliable closing of the ring by
dismantling the shaft. opening the ring. means of a screw and nut at a low
cost.
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
SERIES / B50
ACCESSORIES [FLIGHTS]
Its non-stick side has ribs that project over the surface
to prevent the product from sticking.
N O C LI N G FAC E
50
ST R E A M LI N E FAC E
25
50 Polypropylene
- 150- 150
75 Polyethylene
h
100- 100
100 Polyacetal
75 - 75
150
50 - 50
25 - 25
50
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
h
B50 / SERIES
50
ACCESSORIES [FLIGHTS]
BENT FLIGHT
h
50
45
Polypropylene
Bent Flight 70
Polyethylene
[Streamline + No Cling] 90
Polyacetal
140
SCOOP FLIGHT
42
120
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
SERIES / B50
h
50
4.5
Sentido
de marcha
The side guards are plastic accessories to be inserted
into the belt structure to retain the product laterally,
avoiding overflows and frictions with the conveyor
structure itself.
50 Polypropylene
75 Polyethylene
100 Polyacetal
Drive
direction
It is possible to cut down the standard height for special
applications.
Sens
de marche
B ELT W IT H FLI G H TS A N D S I D E G UA R D S
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
B50 / SERIES
Indent
L.C. L.C.
Indent Indent Indent
Indent Indent
BELT ONLYIndent
WITH SIDE GUARDS Indent BELT WITH FLIGHTS AND SIDE GUARDS
10 10
Indent Indent
10 10
Indent Indent
10 10 10 10
Multiples of 20 mm
10 10 20 mm ●10 10 Multiples of 20 mm 20 mm 10 mm ●
Multiples of 20 + 5 mm 45 mm ● ● ● Multiples of 20 + 5 mm 45 mm 5 mm ● ● ●
BELT WITH
Indent
ZIGZAG FLIGHTS Indent
BELT WITH FLIGHTS, WITHOUT INDENT
10 10 10 10
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
SERIES / B50
50
Ø 17.5
19
48
They are used to fasten the belt to the conveyor in all The distance between the side edge of the belt and
the inflexions. the centre of the hold-down roller (indent) must be a
multiple of 10 mm. Hold-down rollers cannot be used
In applications in which the belt must be submerged,
with the following sprockets:
they are placed in the middle of the belt to prevent it
from getting bent due to the flotation.
Nº of teeth Bore for
They will roll along rails fastened throughout the
T square shaft
conveyor structure. It is recommended to place
wearstrips to avoid the wear owing to rolling as far as 6 40
possible.
50
16
8
23.2
6.4
Ø1
7.
5 19
Multiples of 100 mm 48
D ES I G N DATA
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
B50 / SERIES
200 ÷ 300
R min. 150
Belt width
Wearstrips
C max.
B R min. 150
Belt width
Wearstrips
A
C max.
Roller
Ø mín. 75 Flight support if belt width ≥ 600
R min. 150
200 ÷ 300
B B HORIZONTAL CONVEYOR
C Max.
[C] Distance between the sliding surface of the belt 6 100 42 55 105
and the support of the return way.
8 130.65 58 60 135
[D] If sprockets are used in the inflexion shaft, do 10 161.80 72 76 165
not retain the central one.
12 193.18 89 78 200
[R] This radius must be as big as allowed by
the application in order to minimize the wear
16 256.29 120 80 260
(min. 150 mm). For belts with side guards, consult
about this radius.
[Dimensions in mm] , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
AFHER EUROBELT
SERIES / B50
Minimum quantity
Belt nominal Minimum quantity of wearstrips
width (mm) of sprockets per shaft
Transport way Return way
40 150 1 2 2
160 450 3 2 2
460 750 5 3 2
760 1,050 7 5 3
1,060 1,350 9 6 4
1,360 1,650 11 7 5
1,660 1,950 13 9 6
1,960 2,250 15 10 7
2,260 2,550 17 11 8
2,560 2,850 19 12 9
2,860 3,150 21 14 10
3,160 3,450 23 15 11
3,460 3,750 25 16 12
3,760 4,050 27 18 13
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
20
13
20
ACCESSORIES
6
12
3
30
18
14
8
ACCESSORIES [HOLD-DOWN PROFILES]
20
12
3
7
40
35
6 6
PRO FI LES I N L
6 500
To make the fastening and the support of the belt,
EUROBELT has designed two types of hold-down
32
12
conveyor, reducing the wear of the surfaces in contact,
3
which contributes to prolong the life of the belt.
30
18
Profiles in U
20 x 14 x 2.000
40
35
6 6
6 500
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com
32
ACCESSORIES
ACCESSORIES [WEARSTRIPS]
40 "B"
Ø12.5
Dimensions Materials
Ø 6.5
Polyethylene
6 x 32 x 500 Conductive polyethylene
Polyacetal
The wearstrips arrangement is an important factor in the life span of a conveyor belt. It should be chosen the most suitable
configuration according to the transport needs. To calculate the quantity of supports, the weight of the product to be conveyed
should be taken into account.
It consists of placing the wearstrips in a parallel and The wearstrips are placed throughout the length and
continuous way along the conveyor structure. breadth of the conveyor, as shown in the picture above.
It is preferable to position them so that the joints do not The possible wear that might occur will be even all over
coincide. the belt, since it is resting on the wearstrips lengthwise
and breadthwise.
This is probably the simplest and most economical
configuration although, depending on the load to be With this angle-shaped layout the cleaning and the
transported, uneven wears can arise on the back surface removal of wastes are easy.
of the belt.
It is advisable for applications bearing heavy loads or
It is not advisable for applications with a very heavy load. for high speeds.
AFHER EUROBELT , S.A ● Topacio , 41 E -47012 - VALLADOLID - SPAIN ● CIF:A47028436 ● Phone : + 34 983 217 480 ● afher@eurobelt.com ● www.eurobelt.com