Professional Documents
Culture Documents
Page 1
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
Battery Pack System Components
Figure 1 Figure 2
Components Description
Battery Pack Lamp Selector Switch
Housing (PS 1400 only)
Quick Disconnect
Mounting Slots Wire Harness Plug
Quick Disconnect
Test Switch / Pilot
Light (TS/PL) Battery Pack Power
Connector
TS/PL Mounting
Clip TS/PL Label
TS/PL Connector
Charge Indicator
Sticker
Figure 3
Installation
Step 1 – Install Battery Pack Step 2 – Install Test Switch / Pilot Light
1. Turn off all external power to the luminaire (TS/PL)
2. Inspect Battery Pack and make sure the TSPL
connector is not connected. If so, disconnect it CAUTION
before installation of the Battery Pack.
Fixture contains live wires during portions of the
3. Position the unit in the fixture wireway and fasten
installation. Use insulated tools and gloves.
securely through the Mounting Slots. If
necessary, drill holes and mount with sheet metal 1. Locate a suitable location for the TS/PL and cable
cutting screws (not provided) that is at least 1” from the fixture lamps and is
4. Attach a flat wire tie holder as shown in Figure 2 visible outside the fixture lens
5. Refer to the appropriate wiring diagram, Connect 2. Drill or punch a ½” diameter hole in the fixture wall
unit to the ballast, lamp(s) and AC input power as or wireway cover
indicated in the wiring diagram. 3. Insert one side of TS/PL into the hole from the
6. Attach and fully engage the Quick Disconnect Wire inside of the fixture housing until it snaps in place.
Harness Plug into the Battery Pack Power 4 Slide TS/PL Mounting Clip firmly to lock and
Connector Inspect that the Wire Harness Plug secure the TS/PL assembly
is squarely seated against the Battery Pack Power 5, Mark the TS/PL location on the fixture with the
Connector. TS/PL Label .
7. Insert a wire tie into the flat wire tie holder and pull 6 Apply continuous AC power to the battery pack
the wire tie tight as shown in Figure 3 7. Connect and fully engage the TS/PL Connector
8. Inspect that the Wire Harness Plug is still squarely to the battery pack. Insure the TS/PL Connector
seated against the Battery Pack Power Connector. latch is properly seated in the recess slot on the
battery pack housing
8. Verify the TS/PL light is on.
9. Close fixture housing and insure no possibility of
pinching any wire between housing channel and
cover.
Page 2
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
Page 3
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
Page 4
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
Page 5
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
Wiring Diagrams
RED
RED
BLUE MVOLT
BATTERY PACK
BLUE
Figure A
RED
RED
2 LAMP
RAPID START
BALLAST BLUE MVOLT
BATTERY PACK
BLUE
“B” CONNECT BLACK AND ORANGE
TWO EMERG. LAMP CONNECTION LEADS TOGETHER IF ORANGE
“A” WIRE IS PRESENT
FIGURE B
Page 6
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
MVOLT
BATTERY PACK
Figure C
MVOLT
TWO EMERG. LAMP CONNECTION
BATTERY PACK
“B”
Figure D
Page 7
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
MVOLT
BATTERY PACK
Figure E
MVOLT
BATTERY PACK
Figure F
Page 8
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
MVOLT
BATTERY PACK
Figure H
Page 9
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
“B”
TWO EMERG. LAMP CONNECTION MVOLT
BATTERY PACK
Figure I
FOUR LAMP INSTANT START BALLAST
BALLAST POWER CONNECTION
120 TO 277 VAC SWITCHED OR
UNSWITCHED LINE –
NOTE; VERIFY VOLTAGE RATING
ON LAMP BALLAST
MVOLT
BATTERY PACK
Figure J
Page 10
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
MVOLT
BATTERY PACK
Figure K
MVOLT
BATTERY PACK
Figure L
Page 11
Installation Instructions for Power Sentry Emergency Battery Packs –QD MVOLT Series
MVOLT
BATTERY PACK
Figure M
MVOLT
BATTERY PACK
Figure N
www.powersentrysafety.com
1-800-300-7017
EMCSA00813 Rev C
Page 12