Professional Documents
Culture Documents
The Clematis Wristlet - Cork Version: 10" W X 5.5" H X 2" D
The Clematis Wristlet - Cork Version: 10" W X 5.5" H X 2" D
10” W x 5.5” H x 2” D
SUPPLIES: SEWING TIPS:
Exterior fabric: Backstitching: Backstitching is sewing in
forward and reverse over the same set of stitches to lock them
(2) 12” x 9” sheets of cork OR (1) Fat Eighth (13” x 18”) of at the beginning and end of a line of sewing.
cork
18” length of 1/2” cork strapping WST/WS: An abbreviation that stands for Wrong Side To-
gether OR Wrong Side which indicates which way the fabric
Lining fabric: should face.
(1) Fat quarter of quilt weight cotton RST/RS: An abbreviation that stands for Right Side Together
OR Right Side which indicates which way the fabric should
Interfacing: face.
(1) Fat quarter of Fusible woven interfacing Basting Stitch: To sew using a longer stitch
OPTIONAL: length, commonly done with a stitch length of 4-6 mm.
12” W x 14” H Fusible fleece
Seam Allowance: Seam allowance is always
3/8” (10 mm) unless specified otherwise. For zipper
Notions and supplies: installation, seam allowance is 1/4” (6 mm). Topstitching is
1/8” (3 mm) from the edge. All seam allowances are included
9” of zipper tape in pattern pieces.
(1) 1/2” D-ring
(1) 1/2” Swivel W: an abbreviation that stands for Width
L: an abbreviation that stands for Length
H: an abbreviation that stands for Height
Wrong Side
Wrong side Lining
Lining Exterior
Cork 1
fabric Cork/Vinyl
sewing line
PATTERN PIECES:
Print out pattern pieces using Adobe Reader on regular 8.5” x 11” size paper with scaling set to “Actual Size.” You will need to
tape together both EXTERIOR TOP pieces and both BOTTOM BAND pieces at the centre lines with matching symbols. Do not
overlap symbols. Butt lines and tape together.
2
CUTTING CHART:
Cork Fabric Lining Fabric Fusible woven Fusible fleece
Interfacing
FOR BOTTOM BAND VERSION:
Exterior Top 2
Bottom Band 2
Lining 2 2 2 (Optional)
Slip Pocket 2 2
FOR ONE PIECE EXTERIOR VERSION:
Lining 2 2 2 2 (Optional)
Slip Pocket 2 2
FOR ALL:
D-Ring Strap (cut 2.5” from 18” cork 1
strapping)
Wrist Strap (15.5” of cork strapping) 1
Zipper Tab (1” W x 1.5” H) 2
INTERFACING:
1. Fuse woven interfacing to WS of all matching LINING and 5. Take the WRIST STRAP piece and topstitch along all sides
SLIP POCKET fabric pieces. with 1/8” seam allowance.
STRAP ASSEMBLY:
3.
FOLD OVER
raw end
4. 6.
3
13.
13. Topstitch the top edge of the SLIP POCKET, sewing the 3”
opening shut.
14.
FINAL ASSEMBLY:
Repeat steps 8 and 9 for second EXTERIOR BOTTOM
AND EXTERIOR TOP. 15. Take one ZIPPER TAB and place a small amount of fabric
glue on the WS. Fold in half along the 1” side and slip the
LINING ASSEMBLY: closed end of the zipper tape in between the layers. Use clips
to hold in place until glue dries. Topstitch zipper tab with 1/8”
10. Fold both LINING pieces in half vertically, WST, and mark seam allowance from the edge near the zipper.
the top centre on the RS. Trim away excess ZIPPER TAB so it is the same width as
the zipper tape. Mark the centre of the zipper at 4.5” from
either end.
11. 16.
16. Take your 9” zipper and curve the zipper tape at the open-
11. Pin both SLIP POCKET pieces RST. Sew together, ing outwards at a 90 degree angle and baste in place. Make
leaving a 3” opening along the top for turning the pocket RS sure you’ve angled them at the exact same position on both
out. Make sure to backstitch. sides of the zipper teeth.
4
19. Finger press the exterior and lining pieces away from the
zipper. Do not topstitch yet.
17.
17. Pin your zipper RS up along the top curved edge of one
LINING piece. That LINING piece should also be RS up
making sure the centre mark of your zipper is aligned with the
top centre mark of the LINING piece. Your pull should be on
the left. Baste the zipper in place with 1/8” seam allowance.
20.
20. To topstitch, start at the open end of the zipper along one
set of exterior/lining pieces and backstitch. Then topstitch
along the zipper seam allowance until you reach the zipper
tab at the closed end of the zipper. Rotate and sew across the
zipper tab until you reach the zipper seam allowance for the
other set of exterior/lining pieces. Topstitch along the zipper
18. seam allowance until you reach the opening of the zipper and
backstitch again.
19.
5
23. Trim your seam allowance except at the opening at the
bottom of your LINING pieces. Turn your bag RS out. Fold
FOLD OVER SO THEY in the bottom edges at the opening in the LINING and press.
ARE RST
Sew shut either by hand or with your sewing machine. Attach
your wristlet strap’s swivel to the D-Ring.
You’re Done!
I’d love to see your creations, make sure to
21. use #ClematisWristlet when
you share.
21. Clip the straight edges of the darts RST, and sew together
along the straight edge, making sure to backstitch. Repeat for To create your own tassel zipper pull, follow the tutorial on
remaining 7 darts. the Blue Calla patterns website:
https://bluecallapatterns.com/blogs/sewing-tutorials/create-
your-own-tassel-zipper-pull
21.
22.
22. Open up your zipper at least half way and then pin/clip
both LINING panels RST and both assembled EXTERIOR
PANELS RST. To have a nice end result, make sure that
the seams where your EXTERIOR BOTTOMS are attached
to your EXTERIOR TOPS are aligned as well as the zipper
seams in the middle. You will want the zipper seam allowance
to point towards your lining. Sew all the way around but leave
a 4” opening at the bottom of your lining to turn your wristlet
RS out.
COPYRIGHT AND LICENSING INFORMATION
©2021 Blue Calla Creations. All Rights Reserved. Written permission is required to copy and or
distribute copies of this pattern or instructions. Celine is happy to allow products made from this
pattern by a home sewer to be sold. Patterns must be purchased retail and the items must be
made by one person, in their home. Mass Production is strictly prohibited and will result in a
change to these policies.
CONTACT:
Pattern Shop: https://bluecallapatterns.com
E-mail: bluecallacreations@gmail.com
Follow me on instagram! @bluecallapatterns
Join my Blue Calla Patterns sewing group at:
https://www.facebook.com/groups/bluecallapatterns
1 inch
square
1 inch
square
FOLD