Professional Documents
Culture Documents
1.Subject
Information on release of the new software for Class A AIS (JHS-182)
2.Objective Equipment
- NTE-183 which will replace the JHS-182 requiring replacement.
NOTE: other than JG ships
NOTE: It is unnecessary for ships in which the procedure in the service news
(FSN200001) has been carried out.
3.Outlines
3.1 Changed software
Fixed the following defects in the software of AIS TRANSPONDER (NTE-183).
- "UTC CLOCK : LOST" is displayed in the SENSOR STATUS screen.
- Self-diagnosis results in "INT GPS : NG SAT.RCV".
3.2 Countermeasures
Please update to the new software when visiting a vessel.
If updating the software, please download the new one from Marine Service Dept website.
Make sure to initialize the AIS transponder after updating the software.
There is no revision of the instruction manual and service manual for this software.
Note: Please input a "MR-AIS_" into the head of the subject name of an e-mail.
JQS-2170 X 様式 4(2/2)
4.Attached document
a) Appendix1: Software update procedures for JHS-182 on board (JD20218B)
b) Appendix2: Software update procedures for "NTE-183 for JHS-182 MAINTENANCE AIS
TRANSPONDER" (JD20218A)
c) Appendix3: JHS-182 Software update history
d) Appendix4: AIS maintenance record form
JD20218B
Appendix1
NOTE: NTE-183-2 is written in the software for JHS-183 at the time of shipment.
So be sure to update it to the software for JHS182 when replacing.
1.2 Write down the current setting of each item to the attached JHS-182 setting table.
3. Check and re-set AIS controller referring to the JHS-182 setting table.
3.1 Turn the AIS controller on with maintenance mode.
3.2 Select the following, initialize all transponder data.
“7.INITIAL SETTING” -> “3.AIS INITIALIZE” ->“1.TRANSPONDER ALL CLEAR” -> [ENT]
3.3 Check and compare the current setting of each item with the JHS-182 setting
table created in procedure 1, and re-set the device to fit the table as necessary.
3.4 Once the checking and the re-setting is complete, press OFF key, enter the
password and turn the AIS controller off.
Note: If "UTC CLOCK: IN USE" does not appear, check that the external GPS is
normal. Also, recheck procedure 3.
1-1
JD20218B
Appendix1
4.2 Write down the checked result to the attached ‘AIS JHS-182 Maintenance
record’.
Maintenance-report
E-mail : maintenance-report@jrc.co.jp
Note: Please input a "MR-AIS_" into the head of the subject name of an e-mail.
1-2
JD20218B
Appendix1
1-3
JD20218B
Appendix1
Menu – 7.Initial setting – 2. Ship static data – 8.Internal GPS setting Note
*C
Antenna pos Bow: m
Str : m
Por: m
Sta: m
1-4
Appendix2
Software update procedures for "NTE-183 for JHS-182 MAINTENANCE AIS TRANSPONDER"
(For Update Tool For AIS TRANSPONDER)
1. Preparing
1.1. Prepare the followings:
- Personal computer (OS: Windows7/10, Hard disk free space: 10MBytes or more,
COM (RS-232C) port: built-in port or USB-COM adapter etc.)
- D-SUB 9-pin straight cable (9-pin male connector and 9-pin female connector)
- File (UpdTool.exe) for re-installation
- Update file (nte182v302.img)
1.2. Copy the file (UpdTool.exe) for re-installation and the update file to the desktop holder of
the personal computer.
1.4. In the Main Menu, select [5.MAINTENANCE] - [6.SOFTWARE VERSION] to check the software data
version.
- Press and hold the PWR key, and select [6.SOFTWARE VERSION] to check the software data version.
1.7. Connect the D-SUB 9-pin straight cable between the Maintenance connector of the AIS controller and COM
port (RS-232C) of the personal computer.
AIS Transponder
NTE-183-2
Connection Box
NQE-3182 Power Supply Built-in COM port or
USB-COM adapter etc.
MAINTENANCE connector for RS-232C
D-SUB 9-pin Handheld
AIS Controller straight cable
NCM-779 PC
1
Appendix2
2. Executing of Update
2.1. Turn the AIS controller on with maintenance mode.
- To turn the AIS controller on with maintenance mode, press and hold the MENU key and the PWR key
until characters appear on the AIS controller display.
2.2. In the Main Menu, select [6.FIELD MAINTENANCE] - [6.SOFTWARE UPDATE] - [TRANSPONDERUPDATE].
Select [ENT] on the bottom of the screen, then confirm that the following message is displayed immediately.
2.3. Close any application operating on the personal computer and start the file (UpdTool.exe) for re-installation.
2
Appendix2
2.4. Select “COM Port” menu, and select the connected COM port.
2.5. Click the “Version Check” button to display the version written in the current transponder.
2.6. Double click on the area where "Maintenance Version" is displayed, select the update file (nte182v302.img)
from the file selection screen and click "Open".
Caution:Be sure to select an update file dedicated to NTE-182 MAINTENANCE AIS TRANSPONDER.
3
Appendix2
2.7. Click “Update Start” button to start the software update. Confirm that “Now UpdatingAPL1” is displayed on the
screen of “msg box”.
2.8. About four minutes later, “APL1:Update succeeded” shall be displayed on the screen of “msg box”.
2.9. “APL1:Update succeeded” is not displayed or another message is displayed on the screen of “msg box”,
carry out the procedure of section 4 to retry update.
3.2. Carry out procedure of section 1.3 and 1.4 (software data version check), and confirm that the AIS
transponder software is updated.
3.4. Disconnect the D-SUB 9-pin cable from the Maintenance connector on the rear panel of the AIS controller.
3.5. Tighten the screws to fix the Maintenance connector cover on the rear panel of the AIS controller.
4
Appendix2
If the software update ends unsuccessful, due to D-SUB 9 pin cable came off and communication failed during
update, or ended the File(UpdTool.exe) by mistake etc, retry the update by the following procedure.
Reconnect D-SUB 9 pin cable connecting to the COM port of the personal computer and the maintenance
connector of AIS controller.
In case the File (UpdTool.exe) was ended by mistake, restart the File(UpdTool.exe) and do procedure of section
2.3 - 2.4, then do the following procedure.
4.4. In the Main Menu, select [6.FIELD MAINTENANCE] - [6.SOFTWARE UPDATE] - [TRANSPONDER
UPDATE]. And Select [ENT] on the bottom of the screen.
5
Appendix3
JHS-182 Software Update History
Release Date
Ver Indication Applied S/N
Unit Ver No (yyyy/mm/dd Fixed Items
at Normal Mode from factory
)
NTE-183
3.00 2.00 2018/11/21 Almost the same function as NTE-182 using NTE-183 hardware. -
(for JHS-182)
1) When not improving within 7 minutes after "Tx malfunction" occurs, the AIS
transponder will be restarted automatically.
NTE-183
3.01 2.00 2019/06/20 2) When TX data corruption occurs continuously, the AIS transponder will be restarted -
(for JHS-182)
automatically.
3) Logs of the restart factors are stored.
In order to maintain our records well on the AIS products for future better service, you are kindly
advised to fill in the form below and return it to the following address as soon as possible after
software version, units and /or pc boards replaced with new one(s), please.
Maintenance report
Japan Radio Co., Ltd.
E-mail : maintenance-report@jrc.co.jp
Note: Please input a "MR-AIS_" into the head of the subject name of an e-mail.
Name of Vessel
MMSI No.
Controller NCM-779 BB BB
Apparatus
Serial No.
Transponder NTE-182 BB BB
Service Date
Service Port
Service Order
Service Agent
Service Engineer