Professional Documents
Culture Documents
ZERS:BTS=0575,TRX=011:L;
ZERS:BTS=0576,TRX=013:L;
ZERS:BTS=0576,TRX=014:L;
ZERS:BTS=0577,TRX=016:L;
ZERS:BTS=0577,TRX=017:L;
ZEQS:BTS=0575:L;
ZEQS:BTS=0576:L;
ZEQS:BTS=0577:L;
ZEFS:0172:L;
ZEFS:0172:U;
ZEQS:BTS=0575:U;
ZEQS:BTS=0576:U;
ZEQS:BTS=0577:U;
ZERS:BTS=0575,TRX=010:U;
ZERS:BTS=0575,TRX=011:U;
ZERS:BTS=0576,TRX=013:U;
ZERS:BTS=0576,TRX=014:U;
ZERS:BTS=0577,TRX=016:U;
ZERS:BTS=0577,TRX=017:U;
2G MML Commands
ZEFR:nn Confirm Y Complete site reset, if any calls are current then calls will be
dropped.
ZEFS:nn:L; Locks site U; Unlocks Locks/Unlocks site if any calls are current then
calls will be dropped.
ZEQS:BTS=nn :L; U; Locks/Unlocks sector if any calls are current then calls will be
dropped.
ZEQS:BTS=nn :L:FHO,30; Locks sector after 30 seconds, after forcing the calls to
handover toanother site.
ZERO:BTS=nn; Shows T/S usage & I levels for each TRX for the Sector
ZEQS:BTS=nn :U; Unlock all sectors One at a time(This saves time at the end of the
Planned Work, when Field Op wants site restored to service)
ZNEL; Shows all Signalling links to MSCPlease check commands before use.
ZACC: Enter alarm No. in brackets. (Cancels alarm off MSC/BSC) ZEOR on BTS.
ZCEC:CRCT=345-1&&-3:BA; (=BARRED) then SE; (=SEPARATED) then NU; (=NOT USED) then
SE; (AGAIN!) then WO; (= WORKING)
CGR=1024,FORM=EXT,ST=SE-SY; Shows all channels within Circuit Group that are in the
state
Seperated by System
OMC : ZDCC; ZDRI: Outputs Sync. Info.(esp.on BSC) ZDTI: Checks LAPD (DPNSS) link.
(eg.
ZDTI: NAM=T1084;)
ZEDO: To find out BSC info and BTSs that are connected to the
BSC.
BSC.
ZEFR: Resets BCF and downloads software from BSC. (With parameter OMU, resets omu)
ZYEC: ET , xx : NORM , CRC4 ; Resets counters on ET xx (can help sort out sync.
problems)
ZEOH: Input BCF No. And date/time (Gives alarm history for a site from the
specified date and Time).
ZEAO:BTS=xx; Shows adjacent cell info. Using the BTSs adjacent CI. Check the LAC
and CI of all adjacent cells given (Also on other BSCs)
ZEVV: Downloads s/w database into buffer of BTS. (Used if no d/b
TCSM COMMANDS
ZDDT:TCSM,16;
Instead of going for MML session with BCF go to RADIO NETWORK MANAGEMENT then to
RNW PARAMETERS
USERNAME = EXPERT
PASSWORD = SYSTEM
Examples:
X = Exit
Circuit Groups
Examples:
MxxPyyB1 10yy BT RouteMxxXyyB1 12yy Orange Link/ OWE RouteMxxRyyB1 14yy WAP RAS
RouteMxxWyy 15yy Wildfire RouteMxxZyyB1 16yy Cable & Wireless RouteMxxMyyB9 18yy
Data RouteMxxVyyB1 19yy VPS Route
information.
command input.
info.
ZIAB:MXM:EXEC=N;
3G MML Commands
ZAAP:
GTPU SFU TBU A2SU DMCU FDU WDU VDS VTP VPP LPD SCSI NEMU WBTS NONE
DEFAULT IS ALL */
Output all NIP1s and PETs on RNC(shows which NIP1 PET is on)ZUSI:NIP1,::FULL;
Alarm check on a given PET After checking which NIP1 PET is on)ZAAP:NIP1,X,PET,YY;
where X =NIP1 number, YY=PET number
Alarm check on a given SET After checking which NIS1 SET is on)ZAAP:NIS1,X,SET,YY;
where X =NIS1, YY=SET number
Shows interface ID, VPI, VC and path number for given route.ZLJI:ROU=XX;
Restart unit (with total code load from disk)ZUSU:XXX,Y::C=TOT; where XXX=unit
Y=unit number
2G MML CommandsInformation Locking down a site for a Planned work BSC MML
CommandsCOMMON COMMANDSTCSM COMMANDSNSS MML Info / Commands