Professional Documents
Culture Documents
Lighting
Specifications
Torque
Description Value
Self-tapping Screw - Front Map Lamp 1.5-2 Nm
Nut - Rear Map Lamp 1.5-2 Nm
cardiagn.com
V 2.0 547
Lighting Systems Lighting
cardiagn.com
1. Body Control Module (BCM) 4. Glove Box Light
2. Vanity Mirror Light (if equipped) 5. Boot Light
3. a. Front Map Lamp 6. Rear Map Lamp
V 2.0 548
Lighting Lighting Systems
System Control Diagram
Interior Illumination Control Diagram
cardiagn.com
V 2.0 549
Lighting Systems Lighting
15. Driver Side Door Lock Body Assembly 17. Body Control Module (BCM)
16. Front Passenger Side Door Lock Body Assembly
cardiagn.com
V 2.0 550
Lighting Lighting Systems
Description with the lens and light clamp inside. When the boot is open,
General Description the boot light operates automatically. The boot light is a single
filament bayonet-coupled bulb.
The interior lighting system is controlled by the body control
module (BCM) which is located behind the driver instrument Glove Box Light (if equipped)
panel. The glove box light is located in the hole above the glove box
The interior light system includes: RH. This light is connected to the 2-pin connector with the
mini switch which is located outside the glove box RH, and
• Front Map Lamp operated by the glove box hinge mechanism.
• Rear Map Lamp
When the glove box door is open, the glove box light comes
• Glove Box Light (if equipped) on automatically. The glove box light bulb is a single filament
• Vanity Mirror Light (if equipped) one.
• Boot Light Vanity Mirror Light (if equipped)
• Instrument Panel and Key CylinderLED Illumination The vanity mirror and vanity mirror light are fitted on the
Front Map Lamp visors of the driver and passenger sides. There is a light on each
The front map lamp is fitted on the roof inner garnish in the side of the mirror, and illuminates through the semitransparent
centre above the windshield. The assembly is secured with lens. The bulb can be removed by prying up the lens carefully.
The vanity mirror light can be opened any time whatever status
cardiagn.com
2 screws that are fitted to the mounting bracket which is
connected to the front header and secured on the ceiling with the ignition switch and the master light switch are in.
3 spring clips and 2 solid clips. The vanity mirror light is connected to the roof wire through
The front map lamp assembly has a temporary operation the 2-pin connector. When the vanity mirror cap is open, the
switch and 2 self-lock switches to control the map lamp. simple switch driven by the tang of the cap closes the return
The light is fitted on a plastic housing on which the sunroof circuit and turns on the vanity mirror light. The vanity mirror
switch and Bluetooth microphone of the on-board hands-free light has two 3 W bulbs which are colorized single filament.
telephone system (if equipped) are located. The whole unit is Instrument Panel Back light Illumination
connected to the roof wire using the 4-pin connector.
The instrument panel components, such as the instrument
The front map lamp bulb is a single filament one. The front pack, wireless key cylinder and so on, are all provided with
map lamp lens is made semitransparent to evenly illuminate illumination by LED. The instrument panel lights control their
the cabin. brightness level through the pulse width modulation signal
(PWM) as follows:
The bulb can be replaced after removing the lens. The bulb can
be fitted by pushing it into the bracket, and can be removed by • After inserting the wireless key or turning on the ignition
pulling it gently. switch, the instrument panel light becomes brighter when
Rear Map Lamp the headlights or side marker lights are turned on.
• When the side marker lights are turned off, the
The rear map lamp assembly is located in the centre of the
instrument panel lights fade out.
rear part of the roof inner garnish. The assembly is secured
on the ceiling and can be removed by prying it up from the • The instrument panel lights fade out after removing the
ceiling carefully. The whole unit is connected to the roof wire wireless key.
using the 3-pin connector. Bulb Specification
If the map lamp is fitted with two screws, you need to remove Light Bulb Type Voltage Power
the lens to replace the bulb, and it can be removed with the Glove Box Light C5W 12V 5W
screw being removed. Front Map Lamp C10W 12V 10W
Boot Light Rear Map Lamp C10W 12V 10W
The boot light is located in the middle of the panel which is Boot Light C5W 12V 5W
on the top of the boot. The outer section is a plastic housing
V 2.0 551
Lighting Systems Lighting
cardiagn.com
• Vanity Mirror Light (if equipped) When the ignition switch is at the "AUX" position, with the
• Boot Light unlock key on the wireless key pressed or the door unlocked
• Instrument Panel and Key CylinderLED Illumination with the mechanical key, theBCM activates the synchronous
control function of the relay for the front and rear map lamps.
When theBCM receives signal from the front map lamp main
switch, or the signal indicating that the door or trunklid is open The related function operations are as follows:
or the vehicle is unlocked, theBCM illuminates the interior • The front and rear map lamps come on immediately when
illumination lights. pressing the switches of the lamps.
PWM Control • When opening the glove box, the glove box light,
The main switch on the front map lamp assembly can control controlled by the linked switch, comes on immediately.
the front and rear map lamps. The interior illumination lights • When opening the vanity mirror cap, the simple switch
controlled by thePWM are: the front and rear map lamps, driven by the tang of the cap closes the return circuit and
boot light, instrument panel and wireless key cylinderLED turns on the vanity mirror light.
illumination. If the door is open when the interior illumination
TheBCM can make the Timed-Relay function control the front
lights come on, thePWM output will increase linearly to meet
and rear map lamps in such conditions as follows:
the requirement of the interior illumination and turns on the
room lamps completely after approximately 1.3 seconds. And • When the ignition switch is at the "AUX" position.
if the interior illumination is turned off (unless the ignition • When pressing the unlock key on the wireless key or
switch is at the "AUX" position and the side marker light unlocking the door with the mechanical key.
is turned on), thePWM output will decrease linearly, and
TheBCM can not make the Timed-Relay function control the
turns off the room lamps within approximately 2.8 seconds.
front and rear map lamps in such conditions as follows:
If the interior illumination lights are illuminated when engine
is started, all of them will be turned off immediately, and the • When 15 minutes has elapsed after turning off the
illumination will be recovered automatically after starting is ignition switch.
finished. • When pressing the lock key on the wireless key or
The related function operations are as follows: locking the door with the mechanical key.
• When the vehicle lock system is in the external lock
• The front and rear map lamps fade in when pressing the
condition.
unlock key on the wireless key or unlocking the door
with the mechanical key, and fade out if no door is open • When the ignition switch is at the "start" position.
within 30 seconds. Inertia Switch Operation
• The map lamps fade in after turning off the ignition switch, If the inertia switch is activated or the collision signal is
and the front and rear map lamps fade out if no door is received by the collision sensor when the collision of vehicle
open within 30 seconds. has happened, theBCM will turn on all the interior illumination
V 2.0 552
Lighting Lighting Systems
lights (the lights are on for at least 15 minutes) immediately, light switch to the position of the side marker light or headlight,
cut off the power source of the fuel pump, and unlock the theBCM supplies the power source for the LED. All theLED
door (if the door has been locked). When resetting the inertia illumination is controlled by the PWM.
switch, theBCM turns off all the interior illumination lights.
Instrument Panel Back Light Illumination and
Dimming
The LED supplies illumination for all the switches, panels, key
cylinder and the instrument panel. When rotating the master
cardiagn.com
V 2.0 553
Lighting Systems Lighting
cardiagn.com
4. Disconnect the electrical connector.
Refit
1. Connect the electrical connector.
2. Fit the map lamp clamp, map lamp and screws, and
tighten the screws to 1.5-2 Nm.
3. Fit the map lamp glass cover.
4. Connect the battery negative terminal.
V 2.0 554
Lighting Lighting Systems
Front Map Lamp Bulb Sunroof Switch Set
Removal Removal
1. Disconnect the battery negative terminal. 1. Disconnect the battery negative terminal.
2. Remove the front map lamp glass cover. 2. Remove the front map lamp assembly.
3. Remove the front map lamp bulb. Front Map Lamp Assembly
3. Remove the sunroof switch set.
cardiagn.com
Refit
1. Fit the front map lamp bulb. Refit
2. Fit the front map lamp glass cover. 1. Remove the sunroof switch reserve set.
3. Connect the battery negative terminal. 2. Fit the screws and sunroof switch set.
3. Connect the electrical connector.
4. Fit the front map lamp assembly.
V 2.0 555
Lighting Systems Lighting
cardiagn.com
Rear Map Lamp Assembly
3. Remove the rear map lamp glass cover.
Refit
4. Remove the rear map lamp bulb.
1. Connect the electrical connector.
Refit
2. Press the rear map lamp assembly into the ceiling with
1. Fit the rear map lamp bulb.
the rear map lamp clamp, and secure it with nuts and
2. Fit the rear map lamp glass cover.
tighten the nuts to 1.5-2 Nm.
3. Fit the rear map lamp assembly.
3. Connect the battery negative terminal.
Rear Map Lamp Assembly
4. Connect the battery negative terminal.
V 2.0 556