Professional Documents
Culture Documents
Rolls should be stored In their original wrapping on pallets in dry Core Tolerance
Max outer
closed sun protected place minimum 1 meter from heating units. Application diameter,
diameter, mm
mm Width, mm Order weight
Storage conditions should eliminate any risk of wrapping deterioration. 500
If stored in unheated area Biaxplen films should be placed at room 450 76 ± 10%*
For tobacco
temperature and humidity at least for 48 hours before converting. 120 ± 0,5
films 400 152
300 < 2000 kg ± 20%
It’ is recommended to corona pre treat fi lm before printing Guaranteed
For all 980 > 2000 kg ± 10%
storage life is 6 months from the date of production. ± 3 mm
780 76 > 5000 kg ± 5%
packaging
152
SURFACE TREATMENT films 580 ± 2 mm >10000 kg ± 2%
Metallized film surface energy Is affected by temperature and storage life. Biaxplen guarantees surface treatment level of metallized films higher
than 36 dynes within 15 days after metallization. In order to minimize the deterioration of surface energy it is recommended to store film below 30°C and
to convert it asap. Should film be used for specific application, it is advisable to measure surface energy in order to prove if it suits. Standard roll-
outside corona treated web. Metallized film is advised to be primer covered before printing. Metallized film can be laminated with a number of materials.
It’s highly recommended that the film should be used according to the application recommended by the Producer.
Information given in Techical data sheets is based on typical values checked in standard production. Techical data sheet has not
to be considered a product specification.
* 500 kg
TRANSPARENT FILMS
Biaхplen HGPL
DESCRIPTION:
Heat sealable transparent BOPP film with a standard coefficient B Treated modified heat sealable copolymer skin
of friction and low heat sealing threshold for packaging machines. layer
For high quality rotogravure and flexographic printing and C Transparent oriented polypropylene core layer
lamination. D Heat sealable, non treated skin layer with low seal
intention temperature and standard coefficient
of friction
4
Properties Methods Unit HGPL
Thickness, ± 5% mkm 15 18 20 25 30 35 40 48
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,20 22,75 27,30 31,85 36,40 43,68
Yield, ± 5% m /kg
2
73,26 61,05 54,95 43,96 36,63 31,40 27,47 22,89
MD N/mm , 2 130 140
Tensile strength, not less
TD MPa 230 250
ASTM
GOST 14236 ISO 527
MD D882 220 200
Elongation at break, not more %
TD 80 70
ASTM + 0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 — 0,3
D 1894 - 0,15
MD ASTM 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 3 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec,
UT/UT GOST 27319 ISO 527 D 882, N/15 mm 2,0 2,2 2,3 2,5 2,8
not less
ASTM F 88
ASTM
Haze, not more GOST 15875 ISO 14782 % 2,5 3,0 3,2
D 1003
ASTM
Gloss at 45 °, not less T BIAXPLEN ISO 2813 % 85
D 2457
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 105–140
ASTM Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 38
D 2578 mN/m
Biaхplen HGHL
DESCRIPTION:
Heat sealable transparent BOPP film with low coefficient of friction B Treated modified heat sealable copolymer skin
and low heat sealing threshold for high-speed packaging machines. layer
For high quality rotogravure and flexographic printing and C Transparent oriented polypropylene core layer
lamination. D Heat sealable, non treated skin layer with low seal
intention temperature and low coefficient of friction
6
Properties Methods Unit HGHL
Thickness, ± 5% mkm 15 18 20 25 30 35 40 48
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,20 22,75 27,30 31,85 36,40 43,68
Yield, ± 5% m /kg
2
73,26 61,05 54,95 43,96 36,63 31,40 27,47 22,89
MD N/mm , 2 130 140
Tensile strength, not less
TD MPa 230 250
ASTM
GOST 14236 ISO 527
MD D882 220 200
Elongation at break, not more %
TD 80 70
UT/UT ASTM 0,2 +0,05
Kinetic coefficient of friction GOST 27492 ISO 8295 —
Т/Т D 1894 -0,1
MD ASTM 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 3 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec,
UT/UT GOST 27319 ISO 527 D 882, N/15 mm 2,0 2,2 2,3 2,5 2,8
not less
ASTM F 88
ASTM
Haze, not more GOST 15875 ISO 14782 % 2,5 3,0 3,2
D 1003
ASTM
Gloss at 45 °, not less T BIAXPLEN ISO 2813 % 85
D 2457
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 105 - 140
ASTM Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 38
D 2578 mN/m
Biaхplen HGFL
DESCRIPTION:
Heat-sealing transparent BOPP film with a low threshold of welding, B Treated modified heat sealable copolymer skin
with high coefficient of friction for a special purposes, for high layer
quality rotogravure and flexographic printing and lamination. C Transparent oriented polypropylene core layer
D Heat sealable, non treated skin layer with low
seal intention temperature and high coefficient
of friction
Biaхplen HASL
DESCRIPTION:
Transparent, antifog, both side corona treated BOPP film, for high B Corona treated, heat sealable skin layer with low
quality rotogravure and flexographic printing, for the production coefficient of friction, designed for printing (OUT)
of packaging for salads and vegetables. C Transparent oriented polypropylene tie layer
D Transparent, specially designed, oriented
polypropylene core layer
E Transparent, specially designed, oriented
polypropylene tie layer
F Antifog, corona treated, heat sealable skin layer
with low coefficient of friction (IN)
10
Properties Methods Unit HASL
Thickness, ± 5% mkm 20 25 30 35 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,20 22,75 27,30 31,85 36,4
Yield, ± 5% m /kg2
54,95 43,96 36,63 31,40 27,47
MD 130 140
Tensile strength, not less N/mm2, MPa
TD 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 70
OUT/OUT + 0,1
Kinetic coefficient of friction GOST 27492 ISO 8295 ASTM D 1894 — 0,2
IN/IN - 0,1
MD 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2 2
Biaхplen PGR
DESCRIPTION:
Transparent release BOPP film for high quality rotogravure and B Treated modified copolymer skin layer
flexographic printing and lamination; for the production of flexible C Transparent oriented polypropylene core layer
packaging with frame cold seal glue.
D Non heat sealable, untreated release skin layer
with low coefficient of friction
12
Properties Methods Unit PGR
Thickness, ± 5% mkm 15 20 25 30 35
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 18,20 22,75 27,30 31,85
Yield, ± 5% m /kg
2
73,26 54,95 43,96 36,63 31,40
MD 150 140
Tensile strength, not less N/mm2, MPa
TD 250
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,25
-0,15
MD 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2 2
Haze, not more GOST 15875 ISO 14782 ASTM D 1003 % 2
Gloss at 45 °, not less UT — ISO 2813 ASTM D 2457 % 85
Dyne/cm,
Treatment level, not less T — ISO 8296 ASTM D 2578 38
mN/m
Biaхplen HGSL
DESCRIPTION:
Heat sealable transparent BOPP film for hot climate with a standard B Treated modified heat sealable copolymer skin
coefficient of friction and low heat sealing threshold for packaging layer
machines. C Transparent oriented polypropylene core layer
For high quality rotogravure and flexographic printing and D Heat sealable, non treated skin layer with low seal
lamination. intention temperature and standard coefficient
of friction
14
Properties Methods Unit HGSL
Thickness, ± 5% mkm 15 18 20 25 30 35 40 48
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,20 22,75 27,30 31,85 36,40 43,68
Yield, ± 5% m /kg
2
73,26 61,05 54,95 43,96 36,63 31,40 27,47 22,89
MD N/mm , 2 130 140
Tensile strength, not less
TD MPa 230 250
ASTM
GOST 14236 ISO 527
MD D882 220 200
Elongation at break, not more %
TD 80 70
ASTM + 0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 — 0,35
D 1894 - 0,15
MD ASTM 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 3 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec,
UT/UT GOST 27319 ISO 527 D 882, N/15 mm 2,0 2,2 2,3 2,5 2,8
not less
ASTM F 88
ASTM
Haze, not more GOST 15875 ISO 14782 % 2,3 2,8 3,0
D 1003
ASTM
Gloss at 45 °, not less T BIAXPLEN ISO 2813 % 85
D 2457
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 105–140
ASTM Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 38
D 2578 mN/m
Biaхplen HMPL.M
DESCRIPTION:
Metallized heat sealable BOPP film with a low sealing intention B Aluminum layer
temperature and standard coefficient of friction for printing and C Treated modified copolymer layer for aluminum
lamination. adhesion
D Transparent oriented polypropylene core layer
E Heat sealable non treated, skin layer with standard
coefficient of friction
16
Properties Methods Unit HMPL.M
Thickness, ± 5% mkm 15 18 20 25 30 35 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,20 22,75 27,30 31,85 36,40
Yield, ± 5% m /kg
2
73,26 61,05 54,95 43,96 36,63 31,40 27,47
MD N/mm , 2 130 140
Tensile strength, not less
TD MPa 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 70
ASTM + 0,15
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 — 0,3
D 1894 - 0,15
MD ASTM 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 3 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec, not
UT/UT GOST 27319 ISO 527 D 882, N/15 mm 2,0 2,2 2,3 2,5 2,8
less
ASTM F 88
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °С 105 - 140
Optical density, not less — 1,8
ASTM Dyne/cm,
Treatment level, not less** T BIAXPLEN ISO 8296 36
D 2578 mN/m
Biaхplen HMPLB.M
DESCRIPTION:
Metallized heatsealable BOPP film with low sealing threshold and B Aluminum layer with increased thickness
standard coefficient of friction, with barrier properties, for printing C Treated modified layer for high adhesion
and lamination. to aluminum
D Transparent oriented polypropylene core layer
E Heat sealable, non treated skin layer with standard
coefficient of friction
18
Properties Methods Unit HMPLB.M
Thickness, ± 5% mkm 18 20 30 35 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 16,38 18,20 27,30 31,85 36,40
Yield, ± 5% m /kg
2
61,05 54,95 36,63 31,40 27,47
MD 130 140
Tensile strength, not less N/mm2, MPa
TD 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 70
+ 0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
- 0,10
MD 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 3 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm 2,0 2,3
ASTM F 88
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °С 105 - 140
Optical density, not less — 2,3
Dyne/cm,
Treatment level, not less** T BIAXPLEN ISO 8296 ASTM D 2578 36
mN/m
Water vapour transmission rate at 38 °C, 90% rel. BIAXPLEN — ASTM F 1249 g/m2/24 h 1,0
humidity, 24 h, not more
Oxygen transmission rate at 23 °С, 24 h, not more BIAXPLEN — ASTM D 3985 cm3/m2/24 h 50
Biaхplen HOHMLB.M
DESCRIPTION:
Metallized white pearl microporous heatsealable BOPP film with B Aluminum layer with increased thickness
increased barrier properties for printing and laminations for C Treated modified layer for high adhesion
production of flexible packaging for products with long shelf life. to aluminum
D Oriented polypropylene tie layer
E White Pearl cavitated core layer of orinted
polypropylene
F Oriented polypropylene tie layer
G White pearl heat sealable, non treated skin layer
with standard coefficient of friction
20
Properties Methods Unit HOHMLB.M
Thickness, ± 5% mkm 30 35 40
Density* g/cm3 0,7
BIAXPLEN
Weight, ± 5% g/m2 21,0 24,5 28,0
Yield, ± 5% m /kg
2
47,6 40,8 35,7
MD 70
Tensile strength, not less N/mm2, MPa
TD 140
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 60
0,4 +0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 —
-0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM F 88
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °С 105 - 140
Optical density, not less BIAXPLEN — 2,5
Treatment level, not less** T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 36
Water vapour transmission rate at 38 °C, 90% rel. BIAXPLEN — ASTM F 1249 g/m2/24 h 1
humidity, 24 h, not more
Oxygen transmission rate at 23 °С, 24 h, not more BIAXPLEN — ASTM D 3985 cm3/m2/24 h 90
Biaхplen HMIL.M
DESCRIPTION:
Metallized heat sealable BOPP film with a low sealing intention B Aluminum layer
temperature, long time surface tension shelf life and standard C Treated modified copolymer layer for aluminum
coefficient of friction for printing and lamination. adhesion
D Transparent oriented polypropylene core layer
E Heat sealable non treated, skin layer with standard
coefficient of friction
22
Properties Methods Unit HMIL.M
Thickness, ± 5% mkm 15 18 20 25 30 35 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,20 22,75 27,30 31,85 36,40
Yield, ± 5% m /kg
2
73,26 61,05 54,95 43,96 36,63 31,40 27,47
MD N/mm , 2 130 140
Tensile strength, not less
TD MPa 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 70
ASTM + 0,15
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 — 0,3
D 1894 - 0,15
MD ASTM 5 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 3 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec, not
UT/UT GOST 27319 ISO 527 D 882, N/15 mm 2,0 2,2 2,3 2,5 2,8
less
ASTM F 88
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °С 105 - 140
Optical density, not less — 1,8
ASTM Dyne/cm,
Treatment level, not less** T BIAXPLEN ISO 8296 36
D 2578 mN/m
Water vapour transmission rate at 38 °C, 90% rel. ASTM
BIAXPLEN — g/m2/24 h 1
humidity, 24 h* F 1249
Oxygen transmission rate at 23 °С, 0% rel. ASTM cm3/
BIAXPLEN — 90
humidity 24 h* D 3985 m2/24 h
Biaxplen PMD.M
DESCRIPTION:
None heat sealable metallized BOPP film for the production B Aluminum layer
of decorative packaging. With increased coefficient of friction. for C Treated modified copolymer layer for aluminum
printing and lamination and for decorative packaging. adhesion
D Transparent oriented polypropylene core layer
E Non heat sealable skin layer with high coefficient
of friction, without treatment (by default)
24
Properties Methods Unit PMD.M
Thickness, ± 5% mkm 20 25 30 35 40
Density * g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,2 22,8 27,3 31,9 36,4
Yield, ± 5% m /kg
2
54,9 44,0 36,6 31,4 27,5
MD 140
Tensile strength, not less N/mm2, MPa
TD 280
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,1
Kinetic coefficient of friction UT / UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
- 0,1
Biaxplen HMPLA.M
DESCRIPTION:
Metallized heatsealable BOPP film with low sealing threshold and B Aluminum layer with increased thickness (T)
standard coefficient of friction, with barrier properties for printing C Treated modified layer for aluminum coating, with
and lamination with glue or hot melt. increased heat resistance
D Transparent oriented polypropylene core layer
E Heat sealable, non treated skin layer with standard
coefficient of friction (UT)
26
Properties Methods Unit HMPLA.M
Thickness, ± 5% mkm 18 20 30 35 40
Density * g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 16,38 18,20 27,30 31,85 36,40
Yield, ± 5% m /kg
2
61,05 54,95 36,63 31,40 27,47
MD 130 140
Tensile strength, not less N/mm2, MPa
TD 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 70
+ 0,10
Kinetic coefficient of friction UT / UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
- 0,10
MD 5 4
Thermal shrinkage at 120˚C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 3 2
Heat sealing strength at 130°C, 1bar, 1 sec, ASTM D 882,
UT/UT GOST 27319 ISO 527 N/15mm 2,0 2,3
not less ASTM F 88
Heat sealing range at 1bar, 1sec.* UT / UT °С 105 - 140
BIAXPLEN
Optical density, not less — 2,5
Dyne/cm,
Treatment level, not less ** T BIAXPLEN ISO 8296 ASTM D 2578 36
mN/m
Water vapour transmission rate at 38°C, 90% rel.humidity, 24h, not BIAXPLEN — ASTM F 1249 g/m2/24h 0,1
more
Oxygen transmission rate at 23°С, 24h, not more BIAXPLEN — ASTM D 3985 cm3/m2/24h 15
Biaхplen PGA
DESCRIPTION:
Transparent BOPP film for general purposes for the production B Glossy, treated, none heat sealable skin layer
of adhesive tapes. C Transparent biaxially oriented polypropylene
D Glossy, non treated (by default), none heat sealable
skin layer
28
Properties Methods Unit PGA
Thickness, ± 5% mkm 20 23 25 26 28 32 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,20 20,93 22,75 23,66 25,48 29,12 36,40
Yield, ± 5% m /kg
2
54,95 47,78 43,96 42,27 39,25 34,34 27,47
MD N/mm , 2 150 140
Tensile strength, not less
TD MPa 250
GOST 14236 ISO 527 ASTM D882
MD 180
Elongation at break, not more %
TD 70
ASTM + 0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 — 0,5
D 1894 - 0,1
MD ASTM 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 %
TD D1204 2
ASTM
Heat sealing strength at 130 °C, 1 bar, 1 sec, not
UT/UT GOST 27319 ISO 527 D 882, N/15 mm Non heat sealable
less
ASTM F 88
ASTM
Haze, not more GOST 15875 ISO 14782 % 2
D 1003
ASTM
Gloss at 45 °, not less T BIAXPLEN ISO 2813 % 90
D 2457
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C None heat sealable
ASTM Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 38**/44 ***
D 2578 mN/m
Biaхplen PGD
DESCRIPTION:
Transparent non heat sealable BOPP film for general purposes and B Glossy, treated, none heat sealable polypropylene
decorative packaging. skin layer
C Transparent biaxially oriented polypropylene
D Glossy, none treated, none heat sealable
polypropylene skin layer
30
Properties Methods Unit PGD
Thickness, ± 5% mkm 20 25 30 35 40 48
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,2 22,75 27,30 31,85 36,40 43,68
Yield, ± 5% m /kg
2
54,95 43,96 36,63 31,40 27,47 22,89
MD 140
Tensile strength, not less N/mm2, MPa
TD 250
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,45
- 0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm Non heat sealable
ASTM F 88
Haze, not more GOST 15875 ISO 14782 ASTM D 1003 % 2
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 90
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C Non heat sealable
Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 38
mN/m
Biaхplen PGT
DESCRIPTION:
Transparent non heat sealable BOPP film for textile packaging, B Corona treated, copolymer skin layer
general purposes and decorative overwrapping with high antistatic C Transparent biaxially oriented polypropylene with
properties. antistatic
D Glossy, none treated, none heat sealable
polypropylene skin layer
32
Properties Methods Unit PGT
Thickness, ± 5% mkm 20 25 28 30 35 40
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,20 22,75 25,48 27,30 31,85 36,40
Yield, ± 5% m /kg
2
54,95 43,96 39,25 36,63 31,40 27,47
MD 140
Tensile strength, not less N/mm2, MPa
TD 250
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,4
-0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm Non heat sealable
ASTM F 88
Haze, not more GOST 15875 ISO 14782 ASTM D 1003 % 2
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 90
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C Non heat sealable
Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 38
mN/m
Biaхplen PWA
DESCRIPTION:
White none heat sealable opaque BOPP film for general purposes B Glossy, treated, none heat sealable skin layer
and production of adhesive tapes. C Solid – white opaque oriented polypropylene core
layer
D Glossy, non treated (by default), none heat sealable
skin layer
34
Properties Methods Unit PWA
Thickness, ± 5% mkm 23 25 28 32
Density* g/cm3 0,96
BIAXPLEN
Weight, ± 5% g/m2 22,08 24,00 26,88 30,72
Yield, ± 5% m /kg
2
45,29 41,67 37,20 32,55
MD 120 140
Tensile strength, not less N/mm2, MPa
TD 240 250
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
0,5 + 0,1
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 —
- 0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm None heat sealable
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 45
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 50
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C None heat sealable
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38 **/42 ***
Biaхplen MGS
DESCRIPTION:
One side matt BOPP film for general purposes, for high quality B Matt not treated side
rotogravure and flexographic printing and lamination for flexible C Transparent oriented polypropylene core layer
packaging and labels.
D Treated modified heat sealable copolymer skin
layer
36
Properties Methods Unit MGS
Thickness, ± 5% mkm 15 20 35
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 18,2 31,85
Yield, ± 5% m /kg
2
73,26 54,95 31,40
MD 125
Tensile strength, not less N/mm2, MPa
TD 240
GOST 14236 ISO 527 ASTM D882
MD 220
Elongation at break, not more %
TD 80
+0,15
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,25
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm 2,0 2,3 2,5
ASTM F 88
Haze, not less GOST 15875 ISO 14782 ASTM D 1003 % 70
Gloss at 45 °, not more T BIAXPLEN ISO 2813 ASTM D 2457 % 12
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 130 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen MGD
DESCRIPTION:
Both side matt film for general purposes, for flexographic printing, B Matt not treated side
for decorative packaging. C Transparent oriented polypropylene core layer
D Matt treated side
38
Properties Methods Unit MGD
Thickness, ± 5% mkm 20 30 35
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 18,2 27,3 31,85
Yield, ± 5% m /kg
2
54,95 36,63 31,40
MD 125
Tensile strength, not less N/mm2, MPa
TD 240
GOST 14236 ISO 527 ASTM D882
MD 220
Elongation at break, not more %
TD 80
+0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,35
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm 2,3 2,4 2,5
ASTM F 88
Haze, not less GOST 15875 ISO 14782 ASTM D 1003 % 70
Gloss at 45 °, not more T BIAXPLEN ISO 2813 ASTM D 2457 % 12
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 130 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen MGPL
DESCRIPTION:
One side matt heat sealable BOPP film for general purposes, for B Matt heat sealable, non treated skin layer with low
high quality rotogravure and flexographic printing and lamination seal intention temperature
for flexible packaging and labels. C Transparent oriented polypropylene core layer
D Treated modified heat sealable copolymer skin
layer
40
Properties Methods Unit MGPL
Thickness, ± 5% mkm 15 18 20 35
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,2 31,85
Yield, ± 5% m /kg
2
73,26 61,05 54,95 31,40
MD 125
Tensile strength, not less N/mm2, MPa
TD 240
GOST 14236 ISO 527 ASTM D882
MD 220
Elongation at break, not more %
TD 80
+0,10
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,35
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat sealing strength at 130 °C, 1 bar, 1 sec, not less UT/UT GOST 27319 ISO 527 N/15 mm 2,0 2,3 2,5
ASTM F 88
Haze, not less GOST 15875 ISO 14782 ASTM D 1003 % 70
Gloss at 45 °, not more T BIAXPLEN ISO 2813 ASTM D 2457 % 12
Heat sealing range at 1 bar, 1 sec.* UT/UT BIAXPLEN °C 105 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen MGR
DESCRIPTION:
Matte release BOPP film for high quality rotogravure, flexographic B Matte not treated release skin layer with low
printing and lamination; for the production of flexible packaging coefficent of friction
with frame cold seal glue. C Transparent oriented polypropylene core layer
D Treated smooth modified copolymer skin layer
42
Properties Methods Unit MGR
Thickness, ± 5% mkm 15 18 20
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 13,65 16,38 18,2
Yield, ± 5% m /kg
2
73,26 61,05 54,95
MD 125
Tensile strength, not less N/mm2, MPa
TD 240
GOST 14236 ISO 527 ASTM D882
MD 220
Elongation at break, not more %
TD 80
+ 0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,2
-0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Haze, not less GOST 15875 ISO 14782 ASTM D 1003 % 70
Gloss at 45 °, not more T BIAXPLEN ISO 2813 ASTM D 2457 % 12
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen HOHL
DESCRIPTION:
Heat sealable White Pearlised BOPP film with low seal intention B Treated, heatsealable copolymer skin layer
temperature and standard coefficint of friction for packaging C Transparent oriented polypropylene tie layer
machines.
D White Pearl cavitated core layer of oriented
For high quality rotogravure and flexographic printing and polypropylene
lamination.
E Transparent oriented polypropylene tie layer
F Heat sealable, non treated skin layer with standard
coefficient of friction
44
Properties Methods Unit НOHL
Thickness, ± 5% mkm 30 35 40 45
Density* g/cm3 0,72
BIAXPLEN
Weight, ± 5% g/m2 21,60 25,20 28,80 32,40
Yield, ± 5% m /kg
2
46,30 39,68 34,72 30,86
MD 70
Tensile strength, not less N/mm2, MPa
TD 140
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 60
+ 0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,35
- 0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 40 35 30
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 80
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C 105 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen HWHL
DESCRIPTION:
White heat sealable BOPP film with low seal intention temperature B Treated, heatsealable copolymer skin layer
and standard coefficint of friction for packaging machines. C White opaque oriented polypropylene core layer
For high quality rotogravure and flexographic printing and
D Heat sealable, non treated skin layer with low seal
lamination. intention temperature and standard coefficient
of friction
46
Properties Methods Unit HWHL
Thickness, ± 5% mkm 15 20 30 35
Density* g/cm3 0,96
BIAXPLEN
Weight, ± 5% g/m2 14,40 19,20 28,80 33,60
Yield, ± 5% m /kg
2
69,44 52,08 34,72 29,76
MD 110 120
Tensile strength, not less N/mm2, MPa
TD 210 220 230
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,25
- 0,10
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 60 50 40 35
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 45
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C 105 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen HOHW
DESCRIPTION:
White Pearlised BOPP film with very wide heatsealing range and B Treated, heatsealable copolymer skin layer (T)
standard coefficient of friction for packaging machines. C Transparent oriented polypropylene tie layer
For high quality rotogravure and flexographic printing and
D White Pearl cavitated core layer of oriented
lamination. polypropylene
E Transparent oriented polypropylene tie layer
F Non treated skin layer, with standard coefficient
of friction and very broad heat sealing range (UT)
48
Properties Methods Unit НOHW
Thickness, ± 5% mkm 30 35 40 45
Density* g/cm3 0,72
BIAXPLEN
Weight, ± 5% g/m2 21,60 25,20 28,80 32,40
Yield, ± 5% m /kg
2
46,30 39,68 34,72 30,86
MD 70
Tensile strength, not less N/mm2, MPa
TD 140
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 60
+ 0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,2
- 0,10
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 40 35 30
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 50
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C 75 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen HOHG
DESCRIPTION:
White Pearlised both side corona treated BOPP film with a standard B Corona treated copolymer skin layer (OUT)
coefficient of friction for both side printing, lamination and for C White polypropylene oriented tie layer
“flowpack” packaging with cold seal glue coating.
D White Pearl cavitated core layer of oriented
polypropylene
E Transparent oriented polypropylene tie layer
F Corona treated, glossy, copolymer skin layer with
a standard coefficient of friction (IN)
50
Properties Methods Unit НOHG
Thickness, ± 5% mkm 30 35 40 45
Density* g/cm3 0,73
BIAXPLEN
Weight, ± 5% g/m2 21,90 25,55 29,20 32,85
Yield, ± 5% m /kg
2
45,66 39,14 34,25 30,44
MD 90
Tensile strength, not less N/mm2, MPa
TD 180
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,10
Coefficient of friction, kinetic IN/IN GOST 27492 ISO 8295 ASTM D 1894 — 0,35
- 0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec.* GOST 27319 ISO 527 N/15 mm 2 3
IN/IN ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 40 35
IN 70
Gloss at 45 °, not less BIAXPLEN ISO 2813 ASTM D 2457 %
OUT 85
IN/IN 115 - 140
Heat sealing range at 1 bar, 1 sec* BIAXPLEN °C
OUT/OUT 125 - 140
OUT 38
Treatment level, not less BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m
IN 36
Biaхplen HWHW
DESCRIPTION:
White heat sealable BOPP film with low seal intention temperature B Treated, heatsealable copolymer skin layer
and standard coefficint of friction for packaging machines. C White opaque oriented polypropylene core layer
For high quality rotogravure and flexographic printing and
D Heat sealable, non treated skin layer with low seal
lamination. intention temperature and standard coefficient
of friction
52
Properties Methods Unit HWHW
Thickness, ± 5% mkm 15 20 30 35
Density* g/cm3 0,96
BIAXPLEN
Weight, ± 5% g/m2 14,40 19,20 28,80 33,60
Yield, ± 5% m /kg
2
69,44 52,08 34,72 29,76
MD 110 120
Tensile strength, not less N/mm2, MPa
TD 210 230
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,25
- 0,10
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 60 50 40 35
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 45
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C 75 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen HOSL
DESCRIPTION:
Heat sealable White Pearlised BOPP film with low seal intention B Treated, heatsealable copolymer skin layer
temperature, standard coefficint of friction and high antistatic C Transparent oriented polypropylene tie layer
properties for packaging machines.
D White Pearl cavitated core layer of oriented
For high quality rotogravure and flexographic printing and polypropylene
lamination.
E Transparent oriented polypropylene tie layer
F Heat sealable, non treated skin layer with standard
coefficient of friction
54
Properties Methods Unit НOSL
Thickness, ± 5% mkm 30 35 40 45
Density* g/cm3 0,72
BIAXPLEN
Weight, ± 5% g/m2 21,60 25,20 28,80 32,40
Yield, ± 5% m /kg
2
46,30 39,68 34,72 30,86
MD 70
Tensile strength, not less N/mm2, MPa
TD 140
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 60
+ 0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,35
- 0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM F 88;
Heat sealing strength at 130 °С, 1 bar, 1 sec UT/UT GOST 27319 ISO 527 N/15 mm 2,5
ASTM D882
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 40 35 30
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 50
Heat sealing range at 1 bar, 1 sec* UT/UT BIAXPLEN °C 105 - 140
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Water vapour transmission rate at 38 °C, 90% rel. BIAXPLEN — ASTM F 1249 g/m2/24 h 4,3 3,7 3,3 2,9
humidity, 24 h*
Oxygen transmission rate at 23 °С, 0% rel.humidi- BIAXPLEN — ASTM D 3985 cm3/m2/24 h 1750 1500 1300 1170
ty 24 h*
Biaхplen LGBA
DESCRIPTION:
Transparent BOPP film for labels and for general applications B Treated side of modified copolymer skin layer
for bonding by cold and hot melt adhesives when labelling with C Transparent biaxially oriented polypropylene
improved ink adhesion for printing.
D Glossy, none treated, none heat sealable
polypropylene skin layer with standard coefficient
of friction
56
Properties Methods Unit LGBA
Thickness, ± 5% mkm 30 35 40 48
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 27,30 31,85 36,40 43,68
Yield, ± 5% m /kg
2
36,63 31,40 27,47 22,89
MD 140
Tensile strength, not less N/mm2, MPa
TD 280
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+ 0,1
Kinetic coefficient of friction UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
- 0,1
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Haze, not more GOST 15875 ISO 14782 ASTM D 1003 % 2
Gloss at 45 °, not less UT BIAXPLEN ISO 2813 ASTM D 2457 % 90
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaxplen LOBA
DESCRIPTION:
White Pearl microporous BOPP film for fully wrapped labeling B Modified copolymer corona treated skin layer
of bottles for cold and hot melt glue application while labeling with C White opaque oriented polypropylene tie layer
good gloss and ink adhesion
D White Pearl cavitated core layer of oriented
polypropylene
E Oriented polypropylene tie layer
F Glossy non heat sealable, non treated skin layer
with standard coefficient of friction
58
Properties Methods Unit LOBA
Thickness, ± 5% mkm 35 38 47
Density * g/cm3 0,68
Weight, ± 5% BIAXPLEN g/m2 23,80 25,84 31,96
Yield, ± 5% m /kg
2
42,02 38,70 31,29
MD 80
Tensile strength, not less N/mm2, MPa
TD GOST 14236 ISO 527 ASTM D882 150
MD 200
Elongation at break, not more %
TD 70
GOST 27492 ISO 8295 ASTM D 1894
+0,10
Coefficient of friction, kinetic UT / UT — 0,3
- 0,10
MD 4
Thermal shrinkage at 120˚C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 30 25 20
Gloss at 45°, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 85
Dyne/cm,
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 38
mN/m
Biaхplen LOBB
DESCRIPTION:
White Pearlised microporous glossy BOPP film for fully wrapped B Modified copolymer corona treated glossy skin
labeling of bottles for cold and hot melt glue application while layer
labeling with excellent gloss and high ink adhesion. C Oriented polypropylene tie layer
D White Pearl cavitated core layer of oriented
polypropylene
E Oriented polypropylene tie layer
F Glossy non heat sealable, non corona treated skin
layer with standard coefficient of friction
60
Properties Methods Unit LOBB
Thickness, ± 5% mkm 38 47
Density* g/cm3 0,65
BIAXPLEN
Weight, ± 5% g/m2 24,70 30,55
Yield, ± 5% m /kg
2
40,49 32,73
MD 75
Tensile strength, not less N/mm2, MPa
TD 145
GOST 14236 ISO 527 ASTM D882
MD 190
Elongation at break, not more %
TD 65
+0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 25
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 85
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen LOBC
DESCRIPTION:
White Pearlised microporous BOPP film for fully wrapped labeling B Modified copolymer corona treated skin layer
of bottles for cold and hot melt glue application while labeling with C White opaque oriented polypropylene tie layer
very high yield good gloss and good ink adhesion.
D White Pearl cavitated core layer of oriented
polypropylene
E Oriented polypropylene tie layer
F Glossy non heat sealable, non corona treated skin
layer with standard coefficient of friction
62
Properties Methods Unit LOBC
Thickness, ± 5% mkm 38 47
Density* g/cm3 0,60
BIAXPLEN
Weight, ± 5% g/m2 22,80 28,20
Yield, ± 5% m /kg
2
43,86 35,46
MD 70
Tensile strength, not less N/mm2, MPa
TD 140
GOST 14236 ISO 527 ASTM D882
MD 180
Elongation at break, not more %
TD 60
+0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 35
Gloss at 45 °, not less T BIAXPLEN ISO 2813 ASTM D 2457 % 65
Treatment level, not less Т BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen LOHM.M
DESCRIPTION:
White Pearlised metallized microporous BOPP film for labeling B High glossy aluminum layer
of bottles, for cold and hot melt glue application while labeling. C Modified layer for aluminum adhesion
D Oriented polypropylene tie layer
E White Pearl cavitated core layer of orinted
polypropylene
F Oriented polypropylene tie layer
G Glossy non heat sealable, non treated skin layer
with standard coefficient of friction
64
Properties Methods Unit LOHM.М
Thickness, ± 5% mkm 35 38
Density* g/cm3 0,71
BIAXPLEN
Weight, ± 5% g/m2 24,85 26,98
Yield, ± 5% m /kg
2
40,24 37,06
MD 90
Tensile strength, not less N/mm2, MPa
TD 180
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+0,15
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Optical density, not less BIAXPLEN О.D. 1,8
Treatment level, not less** Т BIAXPLEN ISO 8296 ASTM D2578 Dyne/cm, mN/m 36
Biaхplen LOMB
DESCRIPTION:
Matt White Pearlised microporous BOPP film for fully wrapped B Matt white corona treated skin layer
labeling of bottles. C White opaque oriented polypropylene tie layer
D White Pearl cavitated core layer of oriented
polypropylene
E Oriented polypropylene tie layer
F Glossy non heat sealable, non treated skin layer
with standard coefficient of friction
66
Properties Methods Unit LOMB
Thickness, ± 5% mkm 35 38 47
Density* g/cm3 0,68
BIAXPLEN
Weight, ± 5% g/m2 23,80 25,84 31,96
Yield, ± 5% m /kg
2
42,02 38,70 31,29
MD 80
Tensile strength, not less N/mm2, MPa
TD 150
GOST 14236 ISO 527 ASTM D882
MD 200
Elongation at break, not more %
TD 70
+0,10
Coefficient of friction, kinetic UT/UT GOST 27492 ISO 8295 ASTM D 1894 — 0,3
-0,15
MD 4
Thermal shrinkage at 120 °C, 5 min, not more GOST 18616 ISO 11501 ASTM D1204 %
TD 2
Light transmission, not more GOST 15875 ISO 14782 ASTM D 1003 % 35
Gloss at 45 °, not more T BIAXPLEN ISO 2813 ASTM D 2457 % 13
Treatment level, not less T BIAXPLEN ISO 8296 ASTM D 2578 Dyne/cm, mN/m 38
Biaхplen TSHL
DESCRIPTION:
Thermo shrinkable transparent BOPP film for general purposes B Non treated skin layer (OUT) with a low coefficient
with a wide heat sealing range and low coefficient of friction for of friction and low heat sealingt threshold
“rigid” carton pack overwrapping on high speed machines. C Transparent oriented modified polypropylene
D Non treated skin layer (IN) with a bit higher
coefficient of friction and low heat sealing
threshold
68
Properties Methods Unit TSHL
Thickness, ± 5% mkm 16 18 20
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 14,56 16,38 18,2
Yield, ± 5% m /kg
2
68,68 61,05 54,95
MD 150
Tensile strength, not less N/mm2, Mpa
TD 260
GOST 14236 ISO 527 ASTM D882
MD 180
Elongation at break, not more %
TD 65
IN/IN 0,30 + 0,05
Kinetic coefficient of friction GOST 27492 ISO 8295 ASTM D 1894 —
OUT/OUT 0,25 -0,10
MD 6,5 - 9,0
Thermal shrinkage at 120 °C, 5 min GOST 18616 ISO 11501 ASTM D1204 %
TD 6,5 - 9,0
ASTM D 882,
Heat Seal strength at 1 bar, 1 sec, 130 °C, not less IN/OUT GOST 27319 ISO 527 N/15 mm 2,5
ASTM F 88
Haze, no more GOST 15875 ISO 14782 ASTM D 1003 % 2,5
Gloss at 45 °, not less OUT BIAXPLEN ISO 2813 ASTM D 2457 % 85
Heat sealing range at 1 bar, 1 sec.* OUT/OUT BIAXPLEN °C 105 - 140
MD – Machine, longitudinal direction of the film IN – Internal film side of the reel
TD – Transverse direction of the film OUT- external film side of the reel GOST – Russian Federation standards
* Typical value
TOBACCO FILMS
Biaхplen TGHL
DESCRIPTION:
Tobacco transparent non heat shrinkable BOPP film for general B Non treated skin layer (OUT) with a low coefficient
purposes with a wide heat sealing range and low coefficient of friction and a low heat sealingt threshold
of friction for “soft” and “rigid” carton pack overwrapping. C Transparent biaxially oriented polypropylene
D Non treated skin layer (IN) with a bit higher
coefficient of friction and a low heat sealing
threshold
70
Properties Methods Unit TGHL
Thickness, ± 5% mkm 16 18 20 25 30
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 14,56 16,38 18,2 22,75 27,3
Yield, ± 5% m /kg
2
68,68 61,05 54,95 43,96 36,63
MD 130 140
Tensile strength, not less N/mm2, MPa
TD 230 250
GOST 14236 ISO 527 ASTM D882
MD 220 200
Elongation at break, not more %
TD 80 80
IN/IN 0,3 +0,05
Kinetic coefficient of friction GOST 27492 ISO 8295 ASTM D 1894 —
OUT/OUT 0,2 -0,05
MD 4
Thermal shrinkage at 120 °C, 5 min GOST 18616 ISO 11501 ASTM D1204 %
TD 2
ASTM D 882,
Heat Seal strength at 1 bar, 1 sec, 130 °C, not less IN/OUT GOST 27319 ISO 527 N/15 mm 2,5
ASTM F 88
Haze, no more GOST 15875 ISO 14782 ASTM D 1003 % 2,5
Gloss at 45 °, not less OUT BIAXPLEN ISO 2813 ASTM D 2457 % 85
Heat sealing range at 1 bar, 1 sec.* OUT/OUT BIAXPLEN °C 105 - 140
MD – Machine, longitudinal direction of the film IN – Internal film side of the reel
TD – Transverse direction of the film OUT- external film side of the reel
* Typical value
TOBACCO FILMS
Biaхplen TSHD
DESCRIPTION:
Transparent heat shrinkable BOPP film with a wide heat sealing B Non treated skin layer (OUT) with very low
range and low coefficient of friction specially designed for cigarette coefficient of friction and low heat sealingt
threshold
and tea carton packs overwrapping in high speed machines.
C Transparent oriented modified polypropylene
D Non treated skin layer (IN) with a bit higher
coefficient of friction and low heat sealing
threshold
72
Properties Methods Unit TSHD
Thickness, ± 5% mkm 16 18 20 25
Density* g/cm3 0,91
BIAXPLEN
Weight, ± 5% g/m2 14,56 16,38 18,2 22,75
Yield, ± 5% m /kg
2
68,68 61,05 54,95 43,96
MD 140
Tensile strength, not less N/mm2, MPa
TD 260
MD 180
Elongation at break, not more GOST 14236 ISO 527 ASTM D882 %
TD 70
MD 2700
Flexural modulus* N/mm2, MPa
TD 4500
IN/IN 0,20
Kinetic coefficient of friction GOST 27492 ISO 8295 ASTM D 1894 — ± 0,05
OUT/OUT 0,15
MD 8,5
Thermal shrinkage at 120 °C, 5 min* ± 1,0
TD 6,5
GOST 18616 ISO 11501 ASTM D1204 %
MD 13
Thermal shrinkage at 130 °C, 15 min* ± 2,0
TD 13
ASTM D 882,
Heat Seal strength at 1 bar, 1 sec, 130 °C, not less IN/OUT GOST 27319 ISO 527 N/15 mm 2,5
ASTM F 88
Haze, no more GOST 15875 ISO 14782 ASTM D 1003 % 2,5
Gloss at 45 °, not less OUT BIAXPLEN ISO 2813 ASTM D 2457 % 85
Heat sealing range at 1 bar, 1 sec.* OUT/OUT BIAXPLEN °C 105 - 140
MD – Machine, longitudinal direction of the film IN – Internal film side of the reel
TD – Transverse direction of the film OUT- external film side of the reel GOST – Russian Federation standards
* Typical value
TOBACCO FILMS
Biaхplen TSHT
DESCRIPTION:
Heat shrinkable transparent corona treated BOPP film with a wide B Non treated skin layer with very low coefficient
heat sealing range and low coefficient of friction designed for of friction and low heat sealing threshold (UT)
printing for cigarette and other carton packs overwrapping in high C Transparent oriented modified polypropylene
speed machines. D Corona treated skin layer with a higher coefficient
of friction and low heat sealing threshold (T)
www.sibur.ru/biaxplen