Professional Documents
Culture Documents
Table of contents
1. Knives
1.1 Plotter knives
1.1.1 ZÜND plotter knives for CP, C2, C2-P tool heads
1.1.2 ZÜND and WILD special plotter knives
1.1.3 WILD plotter knives for TA2, TA10, TA100
1.1.4 WILD plotter knives for TA30, TA40, TA41, TA400, TA410, TA500, TA510
2. Routers
2.1 Standard routers shaft Ø 1/8" (3.175mm)
2.2 Routers shaft Ø 3.0mm
2.3 Routers shaft Ø 4.0mm
2.4 Routers shaft Ø 6mm
2.5 Engraving bits shaft Ø 1/8" (3.175mm)
2.6 Engraving bits shaft Ø 3.0mm
3. Accessories
3.1 Accessories for C2, C2-P tool heads
3.2 Accessories for Tz-xx tool heads
3.3 Plotting accessories
3.4 Creasing tools
3.5 Accessories for punch and notch tool head
3.6 Routing accessories
5. Resharpening service
1. Knives
Our standard plotter knives are made of high quality hard metal (HM). This guarantees high durability and
perfect cutting results. In the following chapters there will always be information provided on the knife
angles. The two most important angles are called the cutting-wedge angle (α) and the cutting angle (β).
Generally, the flatter (smaller) the cutting angle (β) is, the better the cutting turns out to be. This is
particularly true for thin materials. A smaller cutting angle, however, increases the overlap. The overlap is
the distance between the centre of the knife and the point of intersection of the cutting edge with the surface
of the material.
The smaller the cutting-wedge angle (α), the “slimmer“ the knife tip is. A slim knife is specially suited to cut
thick materials as it penetrates the material easier. This means a higher risk of breaking the knife tip, which
again may adversely affect its durability.
With thick materials (especially with small radius) a small cutting angle (= large overlap) is
disadvantageous. Narrow curves and radius distort the contours. The same happens when the knives are
set too low.
Experience shows that double-edged knives are more durable. Through the sword-shaped blade, every
corner has an overlap in both directions, in this way the cut foil can easily be lifted out.
Original knives reward you with considerably longer durability and perfect cutting qualitiy. Experienced
specialists are always available to advise you on the most suitable ZÜND / WILD knife for your special
material/application.
1.1.1 ZÜND plotter knives for CP, C2, C2-P tool heads
Price
Type Angle Pack. per
Illustration Description Art. Nr.
(Mat) (α/β) Unit pcs
EURO
X
= possible to resharp (see chapter 5)
Price
Type Angle Pack. per
Illustration Description Art. Nr.
(Mat) (α/β) Unit pcs
EURO
X
= possible to resharp (see chapter 5)
Price
Type Angle Pack. per
Illustration Description Art. Nr.
(Mat) (α/β) Unit pcs
EURO
1.1.4 WILD plotter knives for TA30, TA40, TA41, TA400, TA410, TA500, TA510
Price
Type Angle Pack. per
Illustration Description Art. Nr.
(Mat) (α/β) Unit pcs
EURO
X
= possible to resharp (see chapter 5)
With thick materials (especially with small radius) a large cutting angle is disadvantageous. As a result of
small cutting angles curves do not look round. The same happens when the knives are set too low.
Experience shows that double-edged knives are more durable due to the more stable blade. Through the
sword-shaped blade, every corner has an overlap in both directions. If this overlap is not desired on the face
side of the material, then it can be cut from the rear side should the application permit it. Cutting without an
overlap is not possible!
β β
x x
Oscillating knives
Selecting the appropriate knife depends on the material to be cut. Should the material be fibrous then a
flattened knife is recommended. The wide cutting edge guarantees that no “fibers“ remain and are
completely removed.
If the rate of feed is too high the oscillation creates a perforated instead of an continuous line.
When using a pointed knife the rate of feed has to be drastically reduced in order to achieve good cutting
results.
This figures highlight the difference between a flat knife (fig.1) and a pointed knife (fig. 2). With a pointed
knife and constant cutting parameters parts of the material always remain uncut. Clean seperation is
therefore not possible. The cutting depth with pointed knives would have to be set much lower in order to
cut all fibers. As a result, the cutting surfaces are carved up faster and must be replaced earlier. For thin
and soft materials the use of an EOT (Electrical Oscillatung Tool) is recommended.
Price
Type Angle Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) α/β Unit pcs
EURO
X
= possible to resharp (see chapter 5)
Price
Type Angle Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) α/β Unit pcs
EURO
Tang. knife
Carbide knife for cutting polyester
Z17X) Knife holder
25° foils, leather etc. Usable also for POT 3910307 2 48.00
(HM) Type 3 (yell.)
and EOT oscillating tools.
EOT,POT
Price
Type Angle Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) α/β Unit pcs
EURO
Tang. knife,
ZÜND
Knife holder Universal knife made of super high-
Type 2 90/45° 3910302 10 3.60
Type 2 (blue) speed steel for soft, thin materials
(HSS)
Type 3 (yell.)
Tang. knife,
ZÜND
Knife holder Universal knife made of super high-
Type 3 90/36° 3910303 10 4.20
Type 2 (blue) speed steel for soft materials
(HSS)
Type 3 (yell.)
Tang. knife
ZÜND Universal knife made of super high-
Knife holder
Type 4 36° speed steel for soft, thin materials, 3910304 10 4.20
Type 3 (yell.)
(HSS) like leather
EOT,POT
Tang. knife
ZÜND Universal knife made of super high-
Knife holder
Type 5 36° speed steel for soft , thin materials, 3910305 10 17.00
Type 3 (yell.)
(HSS-TiN) like leather; TiN coated
EOT,POT
Tang. knife
ZÜND
Knife holder Universal knife made of super high-
Type 6 40° 3910310 10 1.60
Type 3 (yell.) speed steel for soft materials
(HSS)
EOT,POT
Tang. knife
WILD Wild Knife Universal knife made of super high-
Type 11 60° holder speed steel for soft materials, 1506281 5 2.20
(HSS) for UWK corrugated paper, etc.
toolhead
X
= possible to resharp (see chapter 5)
1.2.3 ZÜND flat knives 1.5mm thick for POT-40/1.5 (for soft materials up to 50mm)
Price
Type Angle Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) α/β Unit pcs
EURO
Price
Type Angle Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) α/β Unit pcs
EURO
Z30X)
15/40° PPT-32 For passepartout up to 2 mm 3910330 5 22.00
(HM)
Z31
35/30° PPT-32 For passepartout up to 3 mm 3910331 5 31.00
(HM)
Z33
26/38° PPT-40 For passepartout up to 5 mm 3910333 2 25.00
(HM)
Price
Type Dia- Pack. per
Illustration Tool insert Description Art. Nr.
(Mat) meter Unit pcs
EURO
Z50X)
Ø 25mm DRT Decagonal knife for textiles 3910335 1 75.00
(HM)
Z51X)
Ø 28mm DRT Decagonal knife for textiles 3910336 1 82.00
(HM)
Z52X)
Ø 32mm DRT Decagonal knife for textiles 3910337 1 94.00
(HM)
X
= possible to resharp (see chapter 5)
Price
Type Angle Pack. per
Illustration Description Art. Nr.
(Mat) (α/β) Unit pcs
EURO
Osz
Type 1 40° 2 – blades, for soft materials 1506291 5 58.00
(HM)
Osz
Type 2 30° 2 - blades, specially suited for small radius 1506292 1 58.00
(HM)
Osz
Type 3 20° 2 - blades, for harder materials 1506293 5 58.00
(HM)
2. Routers
Price
Cutting
edges
Ø Depth of Pack. per
Illustration Type Description Art. Nr.
[mm] cut [mm] Unit pcs
EURO
Price
Cutting
edges
Price
Cutting
edges
Ø Depth of Pack. per
Illustration Type Description Art. Nr.
[mm] cut [mm] Unit pcs
EURO
Price
Cutting
edges
Price
Cutting
edges
Price
Cutting
edges
Pack. per
Illustration Type Angle Description Art. Nr.
Unit pcs
EURO
Price
Cutting
edges
Pack. per
Illustration Type Angle Description Art. Nr.
Unit pcs
EURO
3. Accessories
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Knife changing tool, type Zünd
3910130 1 15.00
(for knife types Z1 - Z5)
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Insert sleeve for long life cartridge (Super Giant) 3910223 1 140.00
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Creasing wheel Ø 24mm with
holder, creasing width/-depth 3910603 1 220.00
1.5/1.0mm
Creasing wheel Ø 24mm with
holder, creasing width/-depth 3910604 1 220.00
1.5/1.5mm
Creasing wheel Ø 15mm with
holder, creasing width/-depth 5002277 1 220.00
0.7/1.0mm
Creasing wheel Ø 15mm with
holder, creasing width/-depth 5002275 1 220.00
1.1/1.5mm
Folding carton
Creasing wheel Ø 24mm with
holder, creasing width/-depth 3910601 1 220.00
0.7/0.7mm
Creasing wheel Ø 24mm mit
holder, creasing width/-depth 3910602 1 220.00
1.1/1.1mm
Price
Hole Ø Ø tool receiption Pack. per
Illustration Art. Nr.
[mm] [mm] Unit pcs
EURO
0.5 3999211 1 60.00
1.0 3999201 1 47.50
1.2 3999200 1 47.50
1.5 3999202 1 47.50
2.0 3999203 1 47.50
2.5 3999204 1 39.50
7.0
3.0 3999205 1 39.50
3.5 3999206 1 39.50
4.0 3999207 1 39.50
4.5 3999208 1 39.50
5.0 3999209 1 39.50
5.5 3999210 1 39.50
Price
Hole Ø Ø tool receiption Pack. per
Illustration Art. Nr.
[mm] [mm] Unit pcs
EURO
1.0 3999101 1 60.00
1.5 3999102 1 60.00
4.5
2.0 3999103 1 60.00
2.5 3999104 1 60.00
3.0 3999105 1 60.00
3.5 3999106 1 60.00
4.0 7.0 3999107 1 60.00
4.5 3999108 1 60.00
5.0 3999109 1 60.00
Price
Ø tool receiption Pack. per
Illustration Description Art. Nr.
[mm] Unit pcs
EURO
Punching pin 4.5 3999111 1 19.00
Punching pin 7.0 3999112 1 19.00
Price
Pack. per
Illustration Description Art. Nr.
Unit pcs
EURO
Ø 1/8" (3.175mm) 3910492 1 140.00
Ø 2.0mm 3910494 1 95.00
Collet for milling spindle
Ø 2.5mm 1527491 1 95.00
150W+450W
Ø 3.0mm 3910491 1 95.00
Ø 4.0mm 3910493 1 95.00
Ø 6.0 mm 3910496 1 180.00
Ø 1/4" (6.35mm) 3910497 1 190.00
Collet for milling spindle 1 KW NEW Ø 3.0 mm 3910498 1 180.00
NEW Ø 4.0 mm 3910499 1 180.00
NEW Ø 1/8'' 3910500 1 180.00
Cutting/ milling Cutting underlay Cutting underlay N25 Cutting underlay N40
Model underlay 2.5mm 1.0mm 2.5mm 4.0mm
(grey) (brown) (grey) (grey)
S-800 3912140 3912143 3912147 -
1 sheet 1 roll
- -
1500 x 1000mm 1.8 x 20m
CVE-12 3913054 -
CVE-25 3913063 -
CVE-30 3913103 -
1)
up to serial number L12008, article number is 3913039
2)
up to serial number L25006, article number is 3913037
LC-2400 3912160 - -
LC-16/52 3912172 - -
LC-27/32 3912163 - -
TA 30 - 1533160
TA 500 - 2001060
TA 510/ S - 2001061
5. Resharpening service
ZÜND provides a resharpening service for certain knives. Please pay attention to the following points:
- Knives shall be collected and returned in quantities not less than 5 pcs
- Choose a functional packaging to prevent damaged knives caused through shipment
- Normally it is possible to resharp knives several times. Knives with badly damaged cutting edges
or to short knives can not be resharpened again
- The resharpening should not affect the cutting characteristics
- Resharpened knives will be returned within approx. 4 weeks after receipt
- Only original ZÜND knives will be resharpened
Delivery address
ZÜND Systemtechnik AG
Industriestrasse 8
CH-9450 Altstätten
Switzerland
EURO
5.1 ZÜND and WILD plotter knives
Copyright ©
This publication is the property of ZÜND Systemtechnik AG. All coprights of this publication, variations and
electronic data in the form of files or webpages in the internet are exclusively with ZÜND Systemtechnik AG,
CH-Altstätten. Any use as a whole or in part is subject to our written consent. Any violation of this copyright
will be procecuted in criminal court and under civil law.
ZÜND Systemtechnik AG
Industriestrasse 8
CH-9450 Altstätten
Switzerland
Tel: +41 71 757 81 00
Fax: +41 71 757 81 11
Email: info@zund.com
Website: www.zund.com