Professional Documents
Culture Documents
Datasheet
Bently Nevada Machinery Condition Monitoring
Description
The 3300 XL 8 mm Proximity Transducer System consists of:
o One 3300 XL 8 mm probe,
o One 3300 XL extension cable1 , and
o One 3300 XL Proximitor Sensor2 .
Proximitor Sensor
The 3300 XL Proximitor Sensor incorporates numerous
improvements over previous designs. Its physical packaging
allows you to use it in high-density DIN-rail installations. You
can also mount the sensor in a traditional panel mount
configuration, where it shares an identical 4-hole mounting
Document : 141194
Rev. AE
3300 XL 8mm Proximity Transducer System
Datasheet
“footprint” with older Proximitor Sensor already installed. We can also supply connector
designs. The mounting base for either option protectors separately for field installations (such
provides electrical isolation and eliminates the as when an application must run the cable
need for separate isolator plates. The 3300 XL through restrictive conduit). We recommend
Proximitor Sensor is highly immune to radio connector protectors for all installations to
frequency interference, allowing you to install it provide increased environmental protection8 .
in fiberglass housings without adverse effects
from nearby radio frequency signals. The 3300 Extended Temperature Range
XL Proximitor Sensor’s improved RFI/EMI Applications
immunity satisfies European CE mark approvals
without requiring special shielded conduit or An extended temperature range (ETR) probe
metallic housings, resulting in lower installation and ETR extension cable are available for
costs and complexity. applications in which either the probe lead or
extension cable may exceed the standard 177 ˚C
The 3300 XL’s SpringLoc terminal strips require (350 ˚F) temperature specification. The ETR
no special installation tools and facilitate faster, probe has an extended temperature rating for
more robust field wiring connections by up to 218 ˚C (425 ˚F). The ETR extension cable
eliminating screw-type clamping mechanisms rating is up to 260 ˚C (500 ˚F). Both the ETR
that can loosen. probe and cable are compatible with standard
temperature probes and cables, for example,
Proximity Probe and Extension Cable you can utilize an ETR probe with the 330130
The 3300 XL probe and extension cable also extension cable. The ETR system uses the
reflect improvements over previous designs. A standard 3300 XL Proximitor Sensor. Note that
patented TipLoc molding method provides a when you use any ETR component as part of
more robust bond between the probe tip and your system, the ETR component limits the
the probe body. The probe’s cable incorporates system accuracy to the accuracy of the ETR
a patented CableLoc design that provides 330 N system.
(75 lbf) pull strength to more securely attach the
probe cable and probe tip. Description Notes:
You can also order 3300 XL 8 mm probes and
1. One-meter systems do not use an extension
extension cables with an optional FluidLoc cable
cable.
option. This option prevents oil and other
liquids from leaking out of the machine through 2. Proximitor sensors are supplied by default
the cable’s interior. from the factory calibrated to AISI 4140 steel.
Calibration to other target materials is available
Connectors upon request.
The 3300 XL probe, extension cable, and 3. Consult Bently Nevada Applications Note,
Proximitor sensor have corrosion-resistant, Considerations when using Eddy Current
gold-plated ClickLoc connectors. These Proximity Probes for Overspeed Protection
connectors require only finger-tight torque (the Applications, when considering this transducer
connectors will "click" when tight), and the system for tachometer or overspeed
specially-engineered locking mechanism measurements.
prevents the connectors from loosening. These
connectors require no special tools for 4. 3300 XL 8 mm components are both
installation or removal. electrically and physically interchangeable with
non-XL 3300 5 mm and 8 mm components.
You can order the 3300 XL 8 mm probes and Although the packaging of the 3300 XL
extension cables with connector protectors Proximitor Sensor differs from its predecessor,
Standard 5 or 1 Less than ±0.025 mm (±1 mil) with Extended Over a probe and extension cable
meter System components at 0 °C to +45 °C Temperature temperature range of –35 °C to
(+32 °F to +113 °F). Range 5 and 9 +260 °C (-31 °F to +500 °F) with
meter Systems the Proximitor sensor between 0
Standard 9 meter Less than ±0.038 mm (±1.5 mil) °C to +45 °C (+32 °F to +113 °F),
System with components at 0 °C to +45
the ISF remains within ±18% of
°C (+32 °F to +113 °F).
7.87 V/mm (200 mV/mil) and the
Extended Less than ±0.038 mm (±1.5 mil) DSL remains within ±0.152 mm
Temperature with components at 0 °C to +45 (±6 mils).
Range 5 and 9 °C (+32 °F to +113 °F).
Frequency (0 to 10 kHz), +0, -3 dB, with up to Range cable the following total probe
Response 305 meters (1000 feet) of field lengths: 0.5, 1, 1.5, 2, 5, or 9
wiring. meters.
Minimum Target 15.2 mm (0.6 in) diameter (flat Armor (optional on Flexible AISI 302 or 304 SST
Size target) both) with FEP outer jacket.
Shaft Diameter Tensile Strength 330 N (75 lbf) probe case to
(Maximum Rated) probe lead.
Minimum 50.8 mm (2 in)
270 N (60 lbf) at probe lead to
Recommended 76.2 mm (3 in) extension cable connectors.
Minimum
Connector Material Gold-plated brass or gold-
When gapped at the center of the linear range, plated beryllium copper.
the interaction between two separate transducer
systems (cross-talk) will be less than 50 mV on shaft Table 5: Probe Case Torque
diameters of at least 50 mm (2 in) or greater. You Probe Type Maximum Recommended
should take care to maintain minimum separation of Rated
transducer tips, generally at least 40 mm (1.6 in) for
axial position measurements or 38 mm (1.5 in) for Standard forward 33.9 N•m (300 11.2 N•m (100
radial vibration measurements to limit cross-talk to mounted probes in•lbf) in•lbf)
50 mV or less. Radial vibration or position Standard forward- 22.6 N•m (200 7.5 N•m (66
measurements on shaft diameters smaller than 76.2 mount probes - in•lbf) in•lbf)
mm (3 in) will generally change the scale factor. first three threads
Reverse-mount 22.6 N•m (200 7.5 N•m (66
probes in•lbf) in•lbf)
Effects of 60 Hz Magnetic Fields Up to 300 Gauss
Extension Cable Material
Table 4: Output Voltage in Mil pp/Gauss
Standard cable 75 Q triaxial, fluoroethylene
Gap 5- or 1-meter 9- meter Probe Ext. propylene (FEP) insulated
Proximitor Proximitor Cable
Sensor Sensor Extended 75Ω triaxial, perfluoroalkoxy
Temperature (PFA) insulated.
10 0.0119 0.0247 0.0004 0.0004 Range cable
50 0.0131 0.0323 0.0014 0.0014 Minimum Cable 25.4 mm (1.0 in)
90 0.0133 0.0348 0.0045 0.0045 Bend Radius
One non-XL Finger tight plus 1/8 turn using 3300 XL 8 mm probes are
stainless steel pliers designed to seal differential
connector and one pressure between the probe tip
3300 XL connector and case. The probe sealing
material consists of a Viton® O
ring. Probes are not pressure
Proximitor Sensor A308 aluminum tested prior to shipment.
Material Contact our custom design
department if you require a test
Connector Material Gold-plated brass or gold-
of the pressure seal for your
plated beryllium copper.
application.
EMC
EN 61000-6-2
EN 61000-6-4
EMC Directive 2014/30/EU
RoHS
RoHS Directive 2011/65/EU
Maritime
ABS 2009 Steel Vessels Rules
1-1-4/7.7,4-8-3/1.11.1,4-9-7/13
T5 @ Ta= -55 ˚C to + 40 ˚C
T4 @ Ta= -55 ˚C to + 80˚C
3300 XL Probe
ia:
II 1 G
Ex ia IIC T4/T5 Ga
Ex ia IIIC T90C/T105C Dc
For EPL Dc: Temperature Schedule
Ordering Information 5-meter probes are designed for use with the 5
meter Proximitor sensor only.
For the detailed listing of country and product specific
approvals, refer to the Approvals Quick Reference D: Connector and Cable-Type Option
Guide, Document 108M1756, at Bently.com. Miniature coaxial ClickLoc connector with
01
connector protector, standard cable
Ordering Information for Probes
02 Miniature coaxial ClickLoc connector,
standard cable
3300 XL 8 mm Proximity Probes:
11 Miniature coaxial ClickLoc connector with
330101 3300 XL 8 mm Probe, 3/8-24 UNF connector protector, FluidLoc cable
thread, without armor2 12 Miniature coaxial ClickLoc connector,
FluidLoc cable
330102 3300 XL 8 mm Probe, 3/8-24 UNF
thread, with armor2 E: Agency Approval Option
00 Not required
Part Number-AA-BB-CC-DD-EE
05 CSA, ATEX, IECEx Approvals
A: Unthreaded Length Option
13 Armored FluidLoc cable with connector 176467 3300 XL Multi-Purpose Stainless Steel
protector Housing. 12”x8”x6”. Can hold up to 4
3300XL Proximitor Sensors in both DIN-
C: Agency Approval Option mount and panel-mount configurations.
00 Not required (Available with ATEX Zone 0 and Zone 1
certifications.)
05 CSA, ATEX, IECEx Approvals
330181 3300 XL Multi-Purpose Stainless Steel
Housing. 13”x9.5”x7”. Can hold up to 8
3300 XL Extended Temperature Range Proximitor sensors in a DIN-mount
(ETR) Extension Cable configuration or 6 Proximitor Sensors in a
panel-mount configuration. Primarily
330190-AAA-BB-CC used by customers requiring hazardous
area approvals fro their installations.
Available with ATEX Zone 0 and Zone 1
Make sure that the extension cable length and and North American Division 1 and
the probe length, when added together, equal the Division 2 certifications.
Proximitor Sensor total length.
02120015 Bulk field wire. 1.0 mm2 (18 AWG), 3
A: Cable Length Option conductor, twisted, shielded cable with
drain wire. Specify length in feet.
030 3.0 meters (9.8 feet)
138492- Replacement panel-mount mounting
035 3.5 meters (13.1 feet)
01 pad.
040 4.0 meters (11.5 feet)
138493- Replacement DIN-mount mounting pad.
045 4.5 meters (14.8 feet) 01
070 7.0 meters (22.9 feet) 148722- 3300 XL test plug. The 3300 XL Test Plug
01 contains 3 small test pins attached to 3
075 7.5 meters (24.6 feet) color-coded 1-meter wires, each
080 8.0 meters (26.2 feet) terminated in a banana plug. The 3-pin
adapter plugs into the test pin holes on
085 8.5 meters (27.9 feet) 3300 XL-style Proximitor sensors. You can
B: Cable Option use this test plug to check the
performance of the Proximitor sensor
00 Standard cable from the test pin holes in the terminal
01 Armored cable strip without removing the field wiring.
C: Agency Approval Option 04310310 3300 XL Proximitor Sensor panel-mount
screw. One 6-32 UNC thread forming
00 Not required
mounting screw. Four screws are
05 CSA, ATEX, IECEx Approvals required for each Proximitor sensor.
Figure 2: Typical 3300 XL 8mm 9m System over API 670 Testing Range
Figure 3: Typical 3300 XL 8mm Probe over API 670 Operating Range
Figure 10: Frequency Response, Typical 3300 XL 8mm 5m or 1m System with Varying
Lengths of Field Wiring Attached, No Barriers
Figure 11: Phase Response, Typical 3300 XL 8mm 5m or 1m System with Varying
Lengths of Field Wiring Attached, No Barriers
Figure 12: Frequency Response, Typical 3300 XL 8mm 9m System with Varying Lengths
of Field Wiring Attached, No Barriers
Figure 13: Phase Response, Typical 3300 XL 8mm 9m System with Varying Lengths of
Field Wiring Attached, No Barriers
Note: All dimensions shown in millimeters (inches) except as noted.
Copyright 2019 Baker Hughes, a GE company, LLC ("BHGE") All rights reserved.
Bently Nevada, Orbit Logo, Keyphasor and Proximitor are registered trademarks of BHGE in the United
States and other countries. All product and company names are trademarks of their respective holders.
Use of the trademarks does not imply any affiliation with or endorsement by the respective holders.
This product may be covered by one or more patents, see Bently.com/legal for current status.
The information contained in this document is subject to change without prior notice.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 1.775.782.3611 Bently.com