Professional Documents
Culture Documents
Meltshop Equipment Painting: Preparation
Meltshop Equipment Painting: Preparation
C D
Internal External E F
(C3.05) (C4.06)
Preparation
Sandblasting: surface roughness shall be 30 µm - 40 µm sharp-edged
Grade: Sa 2½ x x X X
Surface: shall be free of oil, grease and dirt before starting sandblasting
Primary Coat
Colour: RAL 7035 Light grey
Paint: two-pack zinc dust primer based on epoxy resin
N. of Layers 2
Equipment components
Final Cover Coat Colour According to IDO-L.18.001-1212-ETS-2001 REV. 02
Uncoated surfaces
Uncoated contact or functional surfaces shall be preserved with corrosion protective compound Tectyl
according to SN200. Applied on clean and degreased surfaces.
Bright Parts
Parts like: shafts, bushes, rollers, shims etc., shall be preserved with corrosion protective compound
Tectyl according to SN200. Applied on clean and degreased surfaces.
Hardware
All bolts, nuts, washers must be galvanised except where different indicated (stainless steel, etc.)
SMS-L.18.001-1212-CC-ELT-0001 1
THIS DRAWING AND ALL INFORMATION THERE ON IS THE PROPERTY OF CONCAST AND IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED
UNLESS AUTHORISED BY CONCAST AND IS SUBJECT TO RETURN UPON DEMAND.
ALL RIGHTS RESERVED COPYRIGHT AS PER DRAWN DATE SHOWN IN DRAWING HEADER.
10'121'454 A
Sheet: 1 of 3
Material No.
Description Item
1 2 3 4 5 6 7 8 9 10 11
Preparation
Sandblasting: surface roughness shall be 30 µm - 40 µm sharp-edged
X X X X X X X X X
Grade: Sa 2½
Surface: shall be free of oil, grease and dirt before starting sandblasting
Primary Coat
Colour: RAL 7037 Dusty grey
Paint: two-pack zinc dust primer based on epoxy/polyamide resin
X X X X X X
Thickness: total 80 µm (dry)
Heat resistant: 120 °C
Colour: RAL 7037 Dusty grey
Paint: two-pack zinc dust primer based on silicone
Bright Parts
Parts like: shafts, bushes, rollers, shims etc., shall be preserved with corrosion protective compound X X X X X X X X X X
Tectyl according to SN200. Applied on clean and degreased surfaces.
Hardware
All bolts, nuts, washers must be galvanised except where different indicated (stainless steel, etc.) X X X X X X X X X X X
SMS-L.18.001-1212-CC-ELT-0001 1
THIS DRAWING AND ALL INFORMATION THERE ON IS THE PROPERTY OF CONCAST AND IS CONFIDENTIAL AND MUST NOT BE MADE PUBLIC OR COPIED
UNLESS AUTHORISED BY CONCAST AND IS SUBJECT TO RETURN UPON DEMAND.
ALL RIGHTS RESERVED COPYRIGHT AS PER DRAWN DATE SHOWN IN DRAWING HEADER.
10'121'454 A
Sheet: 2 of 3
Material No.
Printed by: GRJO on 10. January 2019 - Status: Released RE
INTERCONNECTING PIPING
For all interconnecting piping please refer to IDO-L.18.001-1212-ETS-2001 REV. 02
ON-BOARD PIPING
All Rigid On-Board Piping will follow Equipment specific painting colours and thicknesses (both for MSP and CCM) otherwise where not indicated Galvanized Steel will be considered.
Modellversion: -
SMS-L.18.001-1212-CC-ELT-0001 1
Modell:
Workshop Instructions Section Weight Main Scale Format
specified on Material List 1:1 A4
C.6381/403 CAASA Replaced by
Released
Interconnectin & On-Board Piping Painting Approved
& Corrosion Protection Drawn 19.09.2018 VIRL
Document No. Version
10'121'454 A
Sheet: 3 of 3
Material No.