Professional Documents
Culture Documents
Panel PC
APC-1011
www.autonics.com
.
ii © Copyright Reserved Autonics Co., Ltd.
Preface
Preface
Thank you for purchaseing Autonics product.
Please familiarize yourself with the informaton contained in the Safety Precautions section
before using this product.
This user manual contains information about the product and its proper use, and should be kept
in a place where it will be easy to access.
Symbol Descriptions
※1 Annotation mark.
Safety Considerations
Following these safety precautions will ensure the safe and proper use of the product and
help prevent accidents, as well as minimizing possible hazards.
Safety precautions are categorized as Warnings and Cautions, as defined below:
Failure to follow these instructions may result in serious
Warning
injury or death.
Fail-safe device must be installed when using the unit with machinery that may cause
serious injury or substantial economic loss. (e.g. nuclear power control, medical equipment,
ships, vehicles, railways, aircraft, combustion apparatus, safety equipment, crime/disaster
prevention devices, etc.)
Failure to follow this instruction may result in personal injury, economic loss or fire.
Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity,
direct sunlight, radiant heat, vibration, impact, or salinity may be present.
Failure to follow this instruction may result in explosion or fire.
Use the unit within the rated specifications.
Failure to follow this instruction may result in fire or shortening the life cycle of the product.
Do not connect, repair, or inspect the unit while connected to a power source.
Failure to follow this instruction may result in fire.
Check 'Power Wiring' and 'Serial Interface' before wiring.
Failure to follow this instruction may result in fire.
In preparation for product damage, communication error, or malfunction, install external limit
switch, emergency stop switch, or other protection circuit.
Failure to follow this instruction may result in personal injury, economic loss or fire.
Since Lithium battery is embedded in the product, do not disassemble or burn the unit.
Failure to follow this instruction may result in fire.
Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire.
Please contact us for battery replacement.
Use dry cloth to clean the unit, and do not use water or organic solvent.
Failure to follow this instruction may result in fire.
When connecting the power input, use AWG 23 cable or over and tighten the terminal screw
with a tightening torque of 0.5 to 0.8N.m.
Failure to follow this instruction may result in fire or malfunction due to contact failure.
Keep metal chip, dust, and wire residue from flowing into the unit.
Failure to follow this instruction may result in fire or product damage.
Do not push over 2 point at the same time.
Failure to follow this instruction may result in malfunction.
The specifications are subject to change and some models may be discontinued without
notice.
Be sure to follow cautions written in the instruction manual, user manual and the
technical descriptions (catalog, website).
Table of Contents
Preface iii
User Manual Guide ................................................................................................................ iv
User Manual Symbols ............................................................................................................ v
Safety Considerations ............................................................................................................ vi
Cautions during Use ............................................................................................................. viii
Table of Contents ................................................................................................................... ix
2 Installation ................................................................................................. 21
2.1 Product Installation .................................................................................................. 21
2.2 Power Wiring ........................................................................................................... 22
2.2.1 Ground Wiring ............................................................................................ 23
3 Software ..................................................................................................... 25
3.1 Software list ............................................................................................................. 25
3.1.1 Comprehensive Device Management Program [DAQMaster] ................... 25
3.1.2 Comprehensive Motion Device Management Program [atMotion] ............ 26
3.1.3 Vision Sensor Program [Vision Master] ..................................................... 27
3.1.4 Comprehensive Laser Scanner Management Program [atLidar] .............. 28
3.1.5 Drawing Program for GP/LP Panel [GP Editor] ......................................... 29
3.1.6 Logic Panel Programing Program [SmartStudio] ....................................... 30
3.2 Software Installation ................................................................................................ 30
5 Settings ...................................................................................................... 33
5.1 Touchside Settings .................................................................................................. 33
5.1.1 Touch Settings ............................................................................................ 34
6 Maintenance ..............................................................................................37
6.1 Routine Maintenance .............................................................................................. 37
6.2 Regular Maintenance .............................................................................................. 37
1 Product Overview
1.1 Features
Panel PC APC-1011 is a Microsoft Windows 10 based HMI(Human-Machine Interface) or
MMI(Man-Machine Interface) device.
As a display panel and a system unit integrated panel PC, the installation restrictions are less,
User who is familiar with Windows 10 is able to use easily without any education.
1.2 Specifications
※2: The weight includes packaging. The weight in parenthesis is for unit only.
1.3 Dimensions
1.3.2 Bracket
(1) Fixing bracket
No. Description
① Operation indicator (green LED)
② LCD screen
③ HDMI
④ VGA
⑤ USB 2.0
⑥ Ethernet
⑦ USB 3.0
⑧ Audio
⑩ Power switch
⑪ Power terminal
⑭ VESA hole
Serial interface
①
setting jumper pin
② COM2 -
③ JP12 -
Crossover – Cable
PC1 PC2
Cable color
Signal Pin no. Pin no. Signal
Tx+ 1 White Orange 3 Rx+
Tx- 2 Orange 6 Rx-
Rx+ 3 White Green 1 Tx+
4 Blue 4
5 White Blue 5
Rx- 6 Green 2 Tx-
7 White Brown 7
8 Brown 8
2 Installation
4th When additional fixing bracket is in need on the bottom, connect the mold bracket on
the rear of the product, before set fixing bracket. Tighten mold bracket with the M3
screw driver with the tightening torque of 0.3 to 0.5N·m.
3 Software
4 Operating Panel PC
Describes the operation procedure from when the power is supplied on APC-1011 to when the
software is executed.
5 Settings
6 Maintenance
Make sure to use a standard measuring devices, when inspecting the power supply voltage.
When the defect is found, please record and notify us the defect in detail.
When replacing the product, make sure to turn the power off.
When removing dust or dirt, use a dry cloth that does not contain water or detergent.
MTO-APC1011U1-V1.1-1905US