Professional Documents
Culture Documents
ru
SKF stainless steel deep groove ball The main advantage of SKF stainless
Applications
bearings, like their standard steel steel deep groove ball bearings is SKF stainless steel deep groove ball
counterparts, have deep raceway their resistance to corrosion in moistu- bearings are recommended for use
grooves without filling slots and a re and other corrosive environments. wherever resistance to corrosion is
close osculation between raceways They are also highly versatile since the a factor. Typical applications include:
and balls. For this reason they can sealed versions can be supplied with
carry axial loads acting in both direc- dif-ferent grease fillings. This allows ● Food and beverage industry
tions in addition to radial loads, even the choice of the most suitable grease ● Chemical equipment
at high speeds. They have the same for each application, for example, the ● Medical equipment
running properties as standard steel use of food compatible, non-toxic ● Optical instruments
bearings, but with slightly reduced bearing grease for the food industry. ● Printing machines
load carrying capacity. SKF stainless SKF bearings are temperature-stabili- ● Nuclear technology
steel deep groove ball bearings are zed at ● Engines and pumps
available in several designs and sizes, 150 °C but can be used up to 300 °C ● Paper mills
and they are identified as stainless ● Off-shore
steel by the designation prefix W (➔ ● Marine industry
“Range and designs”).
2
www.precise-rotation.ru
Stainless steel deep groove ball bearings www.precise-rotation.ru
Open bearing Bearing with Z shields, suffix 2Z Bearing with RS1 seals, suffix 2RS1
Range and designs Bearing data – general ings with greater or smaller clearance
can be supplied on request.
SKF stainless steel deep groove ball Dimensions The values for radial internal clear-
bearings were formerly available up to The boundary dimensions of metric ance are given in table 1 and are
a maximum bore diameter of 10 mm. stainless steel deep groove ball bear- valid for unmounted bearings under
The line has been expanded with the ings conform to ISO 15-1998. zero measuring load.
series W60, W62 and W63, offering
new possibilities to design engineers Tolerances Materials
having requirements for bearings with Metric stainless steel deep groove ball The bearing rings are produced from
bore diameter up to 50 mm. bearings are manufactured to Normal stainless steel X65Cr14 according to
SKF stainless steel deep groove tolerances corresponding to ISO 492- ISO 683-17:2000 or X105CrMo17
ball bearings are available in the fol- 2002. according to EN 10088-1:1995,
lowing designs: depending on size. The balls are made
Internal clearance of stainless steel X105CrMo17 and
● open (➔ fig 1 ), SKF stainless steel single row deep the shields and cages of stainless
● with non-contact Z shields groove ball bearings are manufactured steel X5CrNi18-10, both according to
(➔ fig 2 ), as standard with Normal radial internal EN 10088-1:1995.
● with contact RS1 seals (➔ fig 3 ), clearance to ISO 5753-1991, but bear-
Radial internal clearance
and on request also with
Table 1
● RS2 seals of fluoroelastomer rubber Bore Radial internal clearance
or d C2 Normal C3 C4 C5
over incl. min max min max min max min max min max
● low-friction RZ seals.
mm µm
In addition, SKF stainless steel deep
groove ball bearings can also be sup- – 10 0 7 2 13 8 23 14 29 20 37
plied 10 18 0 9 3 18 11 25 18 33 25 45
18 24 0 10 5 20 13 28 20 36 28 48
● for shaft-diameters of 0,6 to 9 mm 24 30 1 11 5 20 13 28 23 41 30 53
● for inch shaft-diameters of 0,04 to 30 40 1 11 6 20 15 33 28 46 40 64
40 50 1 11 6 23 18 36 30 51 45 73
0,75 in
● with flanged outer ring
● as thin section bearing.
4
www.precise-rotation.ru
Fig 4 Fig 5 Fig 6 and seal tightly. The RS1 seals are
made of an oil and wear resistant
acrylonitrile butadiene rubber (NBR),
have a sheet metal reinforcement and
can be used at operating temperatu-
res between –40 and +100°C and up
to 120°C for brief periods. They pro-
tect the bearing reliably against moi-
sture and dirt and prevent the leaking
of grease.
Speed ratings
The permissible rotational speeds
depend on the type of the built-in
sealing and the lubrication. The values
Riveted cage Ribbon-type cage Polyamide cage
are given in the product table.
Grease filling
Bearings with shields or seals as
standard are filled for life with a lithium
Cages Seals grease that shows good rust-inhibiting
The bearings are equipped as stand- The bearings of 2Z design are equip- properties and is suitable for tempera-
ard with a riveted cage of pressed ped with pressed shields of stainless tures between –30 and +110 °C.
stainless steel sheet (➔ fig 4 ). On steel. They form a sealing gap with These bearings are maintenance free.
request they can also be supplied with the land of the inner ring shoulder (➔ The grease quantity fills about 25 to
the following cage types: fig 2 ) and allow high temperatures 35 % of the free space in the bearing.
and speeds. Bearings fitted with Details of this grease will be found in
● Riveted brass sheet cage shields are primarily intended for table 2 .
● Ribbon-type cage of steel sheet applications where the inner ring rota- Other lubricating greases can be
(➔ fig 5 ) tes. If the outer ring rotates, there is a supplied on request, for example, for
● Ribbon-type cage of brass sheet risk of grease leaking from the bearing other temperature ranges or, for use in
● Injection moulded cage of polyami- at the food industry (➔ table 2 ).
de 6.6 (➔ fig 6 ). elevated speeds.
The bearings of 2RS1 design are Lubrication of open bearings
equipped with contact seals, which For open bearings, SKF recommends
run with their seal lip on the land of lubrication with one of the approved
the inner ring shoulder (➔ fig 3 ). The and application-proven dependable
seals are fitted with their external SKF bearing greases:
Greases for sealed bearings edge in the recesses at the outer ring
● Grease LGMT 2: all-purpose bearing
Table 2 grease for a wide range of industrial
Characteristics Standard Special grease, Special grease for and automotive applications.
grease food-compatible high temperature ● Grease LGLT 2: low temperature
bearing grease for high speed and
Thickener Lithium soap Aluminium PTFE low noise applications.
complex soap ● Grease LGLC 2: low temperature
Base oil Mineral oil Polyalphaolefin Fluorinated oil bearing grease for high speed and
medium load applications.
Operating –30 to +110 –25 to +120 –35 to +260 ● Grease LGHQ 3: high temperature
temperature, °C
(continuous operation) and low noise bearing grease.
● Grease LGFP 2: food processing
Kinematic viscosity bearing grease USDA H1.
of base oil, mm2/s
at 40 °C 74 150 400
at 100 °C 8,5 15,5 35
Consistency class 2 2 2
(according to NLGI)
5
www.precise-rotation.ru
Stainless steel deep groove ball bearings
d 10 – 50 mm
B
r2
r1
r1
r2
D D1 d d1 D2 d1 D2 d1
2Z 2RS1
mm kN – kg –
1)
Factor for calculating minimum load. For formula, see SKF General Catalogue or SKF Interactive Engineering Catalogue
2)
Calculation factor to determine factor Y when calculating equivalent dynamic bearing load. See SKF General Catalogue or SKF Interactive Engineering Catalogue
6
www.precise-rotation.ru
ra
ra
Da da
mm mm r/min
12 17,2 24,1 25,5 0,3 14 26 0,3 60 000 38 000 60 000 30 000 17 000
18,5 26,2 28 0,6 16,2 27,8 0,6 50 000 32 000 50 000 26 000 15 000
19,3 29,9 31,9 1 17,6 31,4 1 45 000 28 000 45 000 22 000 14 000
17 23,5 30,1 31,9 0,3 19 33 0,3 45 000 28 000 45 000 22 000 13 000
24,9 33,6 35,8 0,6 21,2 35,8 0,6 38 000 24 000 38 000 19 000 12 000
27,5 38,9 41,1 1 22,8 41,2 1 34 000 22 000 34 000 17 000 11 000
20 27,6 35,7 38,7 0,6 23,2 38,8 0,6 38 000 24 000 38 000 19 000 11 000
29,5 39,5 40,9 1 25,2 41,8 1 32 000 20 000 32 000 17 000 10 000
30 41,7 45,4 1,1 27 45 1,1 30 000 19 000 30 000 15 000 9 500
25 31,7 40,2 42,7 0,6 28,2 43,8 0,6 32 000 20 000 32 000 16 000 9 500
34 44,2 45,7 1 30,6 46,4 1 28 000 18 000 28 000 14 000 8 500
38,1 51 53,2 1,1 32 55 1,1 24 000 16 000 24 000 13 000 7 500
40 49,2 59,5 62,5 1 44,6 63,4 1 22 000 14 000 22 000 11 000 6 300
52,9 67,2 70,8 1,1 47 73 1,1 18 000 11 000 18 000 9 000 5 600
7
R www.precise-rotation.ru
Publication Dd 8061/I E
www.precise-rotation.ru