Professional Documents
Culture Documents
A Technical Seminar Report On Recent Development in The Field of Aerodynamics PDF Free
A Technical Seminar Report On Recent Development in The Field of Aerodynamics PDF Free
CERTIFICATE
PRINCIPAL
Contents
1. Introduction
2. Introduction to Aerodynamics
3. Automotive Aerodynamics
4. Aerodynamic forces on a body
INTRODUCTION
When objects move through air, forces are generated by
the relative motion between air and surfaces of the body,
study of these forces generated by air is called
aerodynamics. Based on the flow environment it can be
classified in to external aerodynamics and internal
aerodynamics; external aerodynamics is the flow around
solid objects of various shapes, whereas internal
aerodynamics is the flow through passages in solid
objects, for e.g. the flow through jet engine air
conditioning pipe etc. The behavior of air flow changes
depending on the ratio of the flow to the speed of sound.
This ratio is called Mach number, based on this Mach
number the aerodynamic problems can be classified as
subsonic if the speed of flow is less than that of sound,
transonic if speeds both below and above speed of sound
are present, supersonic if characteristics of flow is greater
than that of sound and hypersonic if flow is very much
greater than that of sound. Aerodynamics have wide
range of applications mainly in aerospace engineering
,then in the design of automobiles, prediction of forces
and moments in ships and sails, in the field of civil
engineering as in the design of bridges and other
buildings, where they help to calculate wind loads in
design of large buildings.
INTRODUCTION TO AERODYNAMICS
In fluid mechanical terms, road vehicle are bluff bodies in very close proximity to the
ground. Their detailed geometry is extremely complex. Internal and recessed cavities which
communicate freely with the external flow (i.e. engine compartment and wheel wells,
respectively) and rotating wheels add to their geometrical and fluid mechanical complexity. The
flow over a vehicle is fully three-dimensional. Boundary layers are turbulent. Flow separation is
common and may be followed by reattachment. Large turbulent wakes are formed at the rear and
in many cases contain longitudinal trailing vortices.
As is typical for bluff bodies, drag (which is a key issue for most road vehicle but far
from the only one) is mainly pressure drag. This is in contrast to aircraft and ships, which suffer
primarily from friction drag. The avoidance of separation or if this is not possible, its control are
among the main objective of vehicle aerodynamics.
With regard to their geometry, road vehicle comprise a large variety of configuration.
Passenger cars, vans and buses are closed, single bodies. Trucks and race cars can be of more
than one body. Motorcycles and some race cars have open drive compartments. With the race car
being the only exception, the shape of a road vehicle is not primarily determined by the need to
generate specific aerodynamic effects as, for instance, an airplane is designed to produce lift.
and height (which define frontal area), are frozen very early in the design process. Even the
details of a car’s proportions are prescribed to close limits for reasons of packing and aesthetics.
Of course, some manoeuvring room must be left to the aerodynamicists. Otherwise, they would
do no more than just measure the aerodynamic characteristics of configuration designed by
others.
Depending on the specific purpose of each type of vehicle, the objectives of aerodynamic
differ widely. While low drag is desirable for all road vehicles, other aerodynamic properties are
also significant. Negative lift is decisive for the cornering capability of race cars, but is of no
importance for trucks are not.
7
Wind noise should be low for cars and buses, but is of no significance for race cars.
There is no question, however, that aerodynamic does influence design. The high trunk
typical of notch back cars with low drag is the most striking example. Despite the fact that it
tends to look “bulky,” it had to be accepted by designer because of its favourable effects on drag
and the extra luggage space it provides. Today’s cars are streamlined more than ever and an
“aero-look” has become a styling feature of its own.
AUTOMOTIVE AERODYNAMICS
Automotive aerodynamics is the study of the aerodynamics of road vehicles. The main concerns
of automotive aerodynamics are reducing drag (though drag by wide wheels is dominating most
cars), reducing wind noise, minimizing noise emission, and preventing undesired lift forces and
other causes of aerodynamic instability at high speeds. For some classes of racing vehicles, it
may also be important to produce desirable downwards aerodynamic forces to improve traction
and thus cornering abilities.An aerodynamic automobile will integrate the wheel arcs and lights
in its shape to have a small surface. It will be streamlined, for example it does not have sharp
edges crossing the wind stream above the windshield and will feature a sort of tail called a
fastback or Kammback or liftback. Note that the Aptera 2e, the Loremo, and the Volkswagen 1-
litre car try to reduce the area of their back. It will have a flat and smooth floor to support the
Venturi effect and produce desirable downwards aerodynamic forces. The air that rams into the
engine bay, is used for cooling, combustion, and for passengers, then reaccelerated by a nozzle
and then ejected under the floor. For mid and rear engines air is decelerated and pressurized in a
diffuser, loses some pressure as it passes the engine bay, and fills the slipstream. These cars need
a seal between the low pressure region around the wheels and the high pressure around the
gearbox. They all have a closed engine bay floor. The suspension is either streamlined (Aptera)
or retracted. Door handles, the antenna, and roof rails can have a streamlined shape. The side
mirror can only have a round fairing as a nose. Air flow through the wheel-bays is said to
increase drag (German source) though race cars need it for brake cooling and a lot of cars emit
the air from the radiator into the wheel bay.Automotive aerodynamics differs from aircraft
aerodynamics in several ways. First, the characteristic shape of a road vehicle is much less
streamlined compared to an aircraft. Second, the vehicle operates very close to the ground, rather
than in free air. Third, the operating speeds are lower (and aerodynamic drag varies as the square
of speed). Fourth, a ground vehicle has fewer degrees of freedom than an aircraft, and its motion
is less affected by aerodynamic forces. Fifth, passenger and commercial ground vehicles have
very specific design constraints such as their intended purpose, high safety standards (requiring,
for example, more 'dead' structural space to act as crumple zones), and certain regulations. Roads
are also much worse (smoothness, debris) than the average airstrip. Lastly, car drivers are vastly
undertrained compared to pilots, and usually will not drive to maximize efficiency.Automotive
aerodynamics is studied using both computer modelling and wind tunnel testing. For the most
accurate results from a wind tunnel test, the tunnel is sometimes equipped with a rolling road.
This is a movable floor for the working section, which moves at the same speed as the air flow.
This prevents a boundary layer forming on the floor of the working section and affecting the
results. An example of such a rolling road wind tunnel is Wind Shear's Full Scale, Rolling Road,
Automotive Wind Tunnel built in 2008 in Concord, North Carolina.
Relationship to velocity
The frictional force of aerodynamic drag increases significantly with vehicle speed. As early as
the 1920s engineers began to consider automobile shape in reducing aerodynamic drag at higher
speeds. By the 1950s German and British automotive engineers were systematically analyzing
the effects of automotive drag for the higher performance vehicles. By the late 1960s scientists
also became aware of the significant increase in sound levels emitted by automobiles at high
speed. These effects were understood to increase the intensity of sound levels for adjacent land
uses at a non-linear rate. Soon highway engineers began to design roadways to consider the
speed effects of aerodynamic drag produced sound levels, and automobile manufacturers
considered the same factors in vehicle design.
Downforce
Downforce describes the downward pressure created by the aerodynamic characteristics of a car
that allows it to travel faster through a corner by holding the car to the track or road surface.
Some elements to increase vehicle downforce will also increase drag. It is very important to
produce a good downward aerodynamic force because it affects the car’s speed and traction.
DRAG
It is the sum of all external forces in the direction of fluid flow, so it acts opposite to the direction
of the object. In other words drag can be explained as the force caused by turbulent airflow
around an object that opposes the forward motion of the object through a gas or fluid.
F=(1/2)CDdV2A
Where: CD= Coefficient of Drag, dependent on the specific geometry of the object, determined
experimentally.
d= Density of air.
V=Velocity of object relative to air.
A= cross section of frontal area.
Since drag is dependent on square of velocity it is most predominant when object is traveling at
very high speeds. It is the most important aerodynamic force to study because it limits both fuel
economy of a vehicle and the maximum speed at which a vehicle can travel.
WEIGHT
It is actually just the weight of the object that is in motion.i.e. the mass of the object multiplied
by the magnitude of gravitational field.This weight has a significant effect on the acceleration of
the object.
THRUST
When a body is in motion a drag force is created which opposes the motion of the object so
thrust can be the force produce in opposite direction to drag that is higher than that of drag so
that the body can move through the fluid. Thrust is a reaction force explained by Newton‟s
second and third laws, The total force experienced by a system accelerating in mass “m” is equal
and opposite to mass “m” times the acceleration experienced by that mass.
FLUID: Webster defines a fluid as "a substance” tending to flow or to conform to the shape of its
container. “This means simply that a fluid is any substance which has little internal friction-i.e.,
one that will easily yield to pressure. All liquids and all gasses are fluid at any temperature or
pressure that interests us. For sure air is a fluid and must inexorably obey all of the laws of fluid
mechanics. Just because the internal friction between the particles which comprise the air that we
breathe and through which we force our race cars is very low does not mean that there is no
pressure present or that the air will behave in the way that we want it to. It will behave in
accordance with the laws of fluid mechanics and in no other way. So we had best achieve a basic
understanding of those laws.
STATIC PRESSURE is defined as the ambient pressure present within a certain space and is
expressed in units of mass related to units of area as in pounds persquare inch (psi).
DYNAMIC PRESSURE is defined as one half of the product of the mass density of a fluid times
fluid velocity squared. We don't have to know that. We do have to know that the dynamic
pressure of a fluid is proportional to the difference between the undisturbed static pressure
present ahead of a body moving through a fluid and the local pressure of the fluid at the point
along the body where we are taking the measurement. Dynamic pressure is directly proportional
to the local momentum of fluid particles.
TURBULENT FLOW is that state of fluid flow in which the various fluid sheets or streamlines
exhibit erratic variations in velocity and do not remain parallel but mix and eddy together.
Turbulent flow causes drag. A common example of laminar and turbulent flow is the behavior of
a plume of cigarette smoke in still air. At first the plume will rise smoothly and the smoke will
remain in ' streamlines. Sooner or later the plume gets tired, becomes' unstable, and turbulence
becomes visible as the streamlines cross and become disrupted.
THE BOUNDARY LAYER is a comparatively thin layer of decelerated fluid adjacent to the
surface of a body in motion through a fluid. Friction between the body and the fluid slows the
fluid flow from its full external value to effectively zero at the surface of the body. The flow
within the boundary layer can be either laminar or turbulent and the layer can be either thin or
thick. At the front of a reasonably well shaped body, as the fluid starts to move out of the way,
the boundary layer will normally be thin and the flow will be laminar. Internal fluid friction and
the friction between the fluid and the body dissipate some of the energy in the fluid and, as the
flow moves rearward over the body, the boundary layer will normally thicken and become
unstable. If it becomes thick enough, or turbulent enough, or if it must flow into a region of
increased pressure, the boundary layer will separate from the body.
PRESSURE DIFFERENTIAL is the local pressure at a given point along the surface of a body
less the static pressure ahead of the body. Variation of the pressure differential along the surface
of a body is referred to as the pressure gradient. A positive pressure gradient-one in which the
pressure differential increases in the direction of flow-is termed an adverse pressure gradient and
can lead to flow separation.
ATTACHED FLOW is the opposite condition to detached flow and is much to be preferred. It is
possible for fluid flow to be turbulent but to remain attached. In fact, a laminar boundary layer
may separate sooner in an adverse pressure gradient than will a turbulent boundary layer.
DRAG is the retarding force which acts on anybody in motion through a fluid. Its action is
always parallel to and in the opposite direction from the direction of motion. Drag is due to the
transfer of momentum between the body and the fluid and is caused by displacement of the fluid
by the body and by friction between the fluid and the body.
PRESSURE DRAG, or PROFILE DRAG is that drag force caused by the displacement of a fluid
by a body in motion through that fluid. Fluid arriving at the leading edge of a body causes a
positive pressure at the leading edge which resists the motion of the body. As the fluid flow
progresses past the leading edge, the pressure rapidly decreases, may become negative for a time,
and then slowly increases until flow separation occurs. The pressure in a region of separated flow
will be negative and will pull against the forward motion of the body just as the high pressure at
the leading edge pushes against it. The sum of these two retarding forces is pressure induced drag
and is the major component of total drag for unstreamlined or semi-streamlined bodies-which
happen to be the sort of bodies that we will be discussing (with the exception of ourwings, which
we hope will be more efficient shapes). With streamlined bodies, skin friction drag is normally
greater than pressure drag. Even with streamlined bodies, we cannot entirely eliminate pressure
drag.
INDUCED DRAG: Induced drag is the drag force produced by a lifting surface as a result of the
lift. A wing, in order to produce lift, will necessarily impart momentum to the fluid. This
momentum is not recovered and appears as drag. The lift doesn't come free and the greater the
lift, the greater the induced drag. We can only hope to induce the minimum amount of drag per
unit of lift generated by appropriate design of the lifting surface. The most effective way of
minimizing the induced drag of a wing is to increase its span. Nature understands this and has
given all of her efficient soaring bird’s wings of great span. Our sanctioning bodies must also
understand since they have decreed that racing car wings be small in span. As a result, the
induced drag of racing car wings is their major drag component.
PARASITE DRAG is the drag produced by the friction and pressure caused by the various
protuberances on the body such as fasteners, heat exchangers, mirrors, air scoops and the like.
Most studies treat skin friction drag as a portion of parasite drag. We will consider it to be
separate.
SKIN FRICTION DRAG is the drag force caused by friction between the surface of a body and
the fluid through which it moves. Its magnitude is a function of surface finish and of surface
area. Strangely enough, skin friction drag is not terribly important in the case of the racing car-
but it is really easy to do something about it.
MOMENTUM, defined as mass time’s velocity, is an indication of the amount of energy that a
body in motion can release if it is stopped. Momentum is constantly transferred from a body in
motion to the fluid through which it moves-by displacement of fluid in order for the body to pass
and by the heat of friction between the body and the fluid. Momentum transferred per unit time is
equal to drag. In order for a body to continue moving through a fluid at a constant speed, the lost
momentum must be constantly replenished by a power source. In order for the body to
accelerate, the power source must produce more thrust than is lost by the transfer of momentum.
Otherwise a vehicle will decelerate or an aircraft will lose either velocity or altitude. Momentum
is transferred from a body to a fluid by:
(I) the displacement of a certain volume of fluid in thedirection of motion and of more fluid in a
direction perpendicular to the direction of motion.
(2) The placement of a certain volume of fluid into turbulence or irregular motion.
(3) The containment of a certain volume of fluid in a system of regular vortices.
(4) The generation of heat by friction between the fluid and the body and between fluid sheets
moving at differing relative velocities.
VISCOSITY is the molecular resistance which fluid particles exhibit against lisplacement in
relation to each other and with respect to the surface of a body. Most directly this type of
resistance presents itself in the form of frictional drag-as a tangental force when fluid moves past
the surface of a body. This tangental force is skin friction drag and increases with viscosity. The
viscosity of air is, for our purposes, independent of pressure and although it decreases with rising
temperature, we shall consider it to be constant.
COMPRESSIBILITY is the quality of a gaseous fluid of reducing in volume as static pressure is
increased. In practical terms, liquids are not compressible and gasses are-which is why bubbles
in the braking system cause a spongy brake pedal. At vehicle speeds we do not approach
incompressible airflow, so we will not worry about it.
REYNOLDS NUMBER is a dimensionless quantity which varies directly with air speed and size
of the body in motion and inversely as fluid density and viscosity. Its chief value lies in enabling
fluid mechanicists to predict full scale results from model tests. It has limited practical
application within the scope of this chapter.
THE COEFFICIENT OF DRAG is a dimensionless quantity used to compare the drag caused
bodies of different shapes It is abbreviated to CD and is obtained by measuring the drag force
and dividing it by the dynamic pressure and the reference area.
THE COEFFICIENT OF LIFT is another dimensionless quantity which compares the lift
generated by different
shapes. It is normally abbreviated C I and is obtained by measuring the lift force and dividing it
by the dynamic pressure and the reference area.
Blockage Usually referred to as a percentage, this is the ratio of the frontal area of the
vehicle being tested to the cross-sectional area of the wind tunnel. For a solid
tunnel 4-5% would be a typical “good” value. Higher numbers would begin to
require significant blockage correction.
Blockage Correction Forces directly measured on a wind tunnel model are often “corrected” to allow
for the effects on forces caused by the (close proximity of the) walls of the
wind tunnel. Typically this will involve reductions in both the drag and lift values
with different corrections for each. The “correction” factors are typically derived
from standard bluff bodies tested at many blockages.
Boundary Layer As air passes over a stationary surface, the air nearer the surface moves more
slowly than air further away. Over time and distance, this layer of slow-moving
air builds up. This is the boundary layer.
Contact Patch The point where the tire touches the road. Being flexible, the tire is squashed
locally creating a contact patch, which increases as the vertical load on the tire
increases. Simplified you could imagine that the tire is cut by the plane of the
road.
Double Diffuser A diffuser is limited in size by regulation and creates downforce by creating a
pressure differential, with low pressure beneath and higher pressure
above. Clever interpretation of the rules regarding holes in the floor and
continuous surfaces led to the openings that allowed double diffusers.
Effectively the step formed two separate, but individually continuous, surfaces
allowing airflow to pass up above the step plane into the upper deck of the
diffuser. This rule was clarified for 2011 and now a single continuous surface
must be formed under the floor.
Double DRS (DRD) (See DRS below). Active systems (eg Mercedes system where air was
channelled through an opening in the rear-wing endplate when the DRS was
activated and then fed through the car to help stall the front wing) banned for
2013 and beyond. Passive systems (sometimes known as Drag Reduction
Devices [DRDs]) with no moving parts other than the airflow through them are
still allowed.
Downforce For the purist, this should be referred to as “negative lift”, since most
aerodynamic devices were invented for aircraft and were designed to lift them
into the air. It is the vertical part of the aerodynamic force generated by the car
as it moves through the air.
Drag This is the horizontal part of the aerodynamic force generated by the car as it
moves through the air. This force is so great on a F1 racing car that, when the
driver comes off the throttle at maximum speed, the car slows down at least as
briskly as a road car can brake at maximum effort.
Drag Coefficient Usually shown as Cd or Cx. Changes as a function of the shape of the body.
Drag force changes as a function of Cd or Cx and flow direction, fluid/air
density and viscosity, object position and size, and speed; and is proportional
to the density of the fluid/air and to the square of the relative speed between
the fluid/air and the object.
DRS - Drag An overtaking aid which allows the driver to make an adjustment to the rear
Reduction System wing from the steering wheel and deactivated when the driver brakes. Can only
be used in DRS zones (designated areas of the track) in qualifying and, during
the race, if the following car is within one second of the car in front at the DRS
detection points. Race Director may decide to suspend use in adverse weather
conditions or in a yellow-flag zone. The rear wing flap must be at least 10mm
from the main plane when closed and no more than 65mm when open.
Exhaust Effect The exhaust from a F1 engine exits the tailpipe at high speed (was
approximately 1100 kph/700 mph in 2013) depending on exhaust pipe
diameter and temperature. This exhaust gas can, in certain circumstances, be
used to reduce drag or increase downforce. In other circumstances, it can do
quite a bit of damage, due to its extremely high temperature, severely damage
the car mechanically (such as melting the wings). For 2014 exhaust diameters
have been increased (which then reduces speed in the pipes) and moved to an
area where less (aero-wise) can be achieved.
F-Duct McLaren were the first to use. They managed to redirect airflow over the rear
wing, allowing the flap to stall and increasing top speed by a few kph, and
controlled by a vent in the cockpit which could be blocked by the driver’s leg.
The rules were then clarified and, from 2011, any system, device or procedure
which uses driver movement as a means of altering the aerodynamic
characteristics of the car is prohibited.
Ground Effect A curved aerodynamic surface influences the airflow even a long way from that
surface, bending the airflow in such a way that flow adjacent to the surface
follows that surface almost perfectly. The further away from the surface you go,
the straighter the flow becomes. When an aerodynamic surface is placed close
to the ground, the presence of the ground determines where the flow becomes
straight. This has the effect of speeding up the airflow between the surface and
the ground, increasing the aerodynamic effect of the surface.
Pitch When the front and rear ride heights are different to one another; the car is
said to be pitched. Pitch can be expressed as an angle or as a difference
between the front and rear ride heights.
Reynolds Number Ratio of speed, length and air density to fluid/air viscosity. At low levels of
Reynolds Number (ie equal to or below 2300) flow is laminar, at higher levels
(ie above 4000) is turbulent and, in between, is in transition.
Ride Height Height or average height of the car to the ground. Each team has its own
plane or point of reference for ride height.
Roll This is the difference in ride height left to right and is usually expressed as an
angle to the ground.
Stall When an aerodynamic surface curves too quickly for the air particles to follow
the shape of the surface, the airflow is said to be stalled.
Steer Turning the steering wheels (front in F1) at an angle to the vehicle. Just like
the effect of turning the steering wheel in a road car.
Subsonic Literally, below the speed of sound. The reason this is important in
aerodynamics is that there is a dramatic, almost switch-like, change in the way
air behaves when the speed of sound is reached.
Supersonic Above the speed of sound. At supersonic speeds, airflow sometimes appears
as a shock wave and seems to move in straight lines.
Vortex Swirling flow of air. A vortex would occur at the tip of a wing where the air
passing around the wing is deflected just beside air that does not touch the
wing. The sudden change in flow angularity created by the meeting of these
two different flow directions creates the swirling mass of air. Rear-wing
vortices can be seen on racing cars in damp conditions. Sometimes vortices
are generated on purpose to control airflow such as the small angled rectangles
that protrude above many aircraft wings. F1 teams are investigating vortex
generators to push the limits of aerodynamic downforce further than they now
can.
Yaw A car is said to be in yaw when it corners with a sliding (usually tail-out)
attitude. In other words, the car is cornering sideways.
PRINCIPLES OF AERODYNAMICS
Coanda Effect
A moving stream of fluid in contact with a curved surface will tend to follow the curvature of the
surface rather than continue traveling in a straight line. One of the most widely used applications
of Bernoulli's principle is in the airplane wing. Wings are shaped so that the top side of the wing
is curved while the bottom side is relatively flat. In motion, the front edge of the wing hits the
air, and some of the air moves downward below the wing, while some moves upward over the
top. Since the top of the wing is curved, the air above the wing must move up and down to
follow the curve around the wing and stay attached to it (Coanda effect), while the air below the
wing moves very little. The air moving on the top of the curved wing must travel farther before it
reaches the back of the wing; consequently it must travel faster than the air moving under the
wing, to reach the back edge at the same time. The air pressure on the top of the wing is therefore
less than that on the bottom of the wing, according to Bernoulli’s principle. The higher pressure
air on the bottom of the wing pushes up on the wing with more force than the lower pressure air
above the wing pushes down. This result in a net force acting upwards called lift. Lift pushes the
wings upwards and keeps the airplane in the air. Though Bernoulli's principle is a major source
of lift in an aircraft wing, Coanda effect plays an even larger role in producing lift. If the wing is
curved, the airflow will follow the curvature of the wing. In order to use this to produce lift, we
need to understand something called angle of attack. This gives the angle between the wing and
the direction of the air flow, as shown in the following picture. The angle of attack indicates how
tilted the wing is with respect to the oncoming air. In order to produce lift, or downforce acting
on the wing, Newton's third law says that there must be equal force acting in the opposite
direction. If we can exert a force on the air so that it is directed down, the air will exert an
upward force back on the wing.
This diagram shows that increasing the angle of attack increases how much the air is deflected
downwards. If the angle of attack is too high, the air flow will no longer follow the curve of the
wing (Coanda effect is losing the power). As shown in the bottom of the diagram, this creates a
small vacuum just behind the wing. We can say that wing is stalled. As the air rushes in to fill
this space, called cavitations’, it causes heavy vibrations on the wing and greatly decreases the
efficiency of the wing. For this reason, aircraft wings are generally angled like the middle wing
in the diagram. This wing efficiently directs the airflow downward, which in turn pushes up on
the wing, producing lift. If you turn this wings on upper picture upside down, you get formula 1
or any wing in use in auto sport. This configuration of the wing, with longer lower part of
the wing will produce opposite force, called downforce. But we can apply same rules. To get
around air stream separation problem in airplane wing construction and in Formula 1, and
increase the Coanda effect on wings, dual or more element or slot-gap wings are used, these
allow for some of the high pressure flow from (in Formula 1 case) the upper surface of the wing
to bleed to the lower surface of the next flap energizing the flow. This increases the speed of the
flow under the wing, increasing downforce and reducing the boundary flow separation. If you
look at a F1 rear wing few years ago on picture above, you can see this concept taken to the
extreme, with multi-element wings creating huge amounts of downforce and little air stream
separation even on the flaps with extremely high angle of attack. The Coanda effect has
important applications in various high-lift or high downforce devices on aircraft, or in our area of
interest, on the racing car wing, where air moving over the wing can be "bent" using flaps over
the curved surface of the top of the wing. The bending of the flow results in its acceleration and
as a result of Bernoulli's principle pressure is decreased; aerodynamic lift or downforce is
increased. Notice how unlikely is to have a wing in flight with air flow only on one side. The
Coanda effect only works in specific conditions where an isolated jet of fluid (or air) flows
across a surface, a situation which is usually man-made. You don't find it much in nature. Just so
you know, there is no Coanda lift on an airfoil. Coanda effect helps airstream to stay attached to
the wing surface, but Bernoulli principle and difference in pressures are the reason why we have
a lift or downforce. Coanda effect is a balancing act between many factors, among them speed of
fluids stream, pressure, molecular attraction, and a centrifugal effect if the surface is curved.
Main trouble of the Coanda effect is the airstream becoming turbulent and detaching from the
surface, that's how a wing stalls. Pull of surrounding air causes turbulence, drag from the surface
and from the ambient air. It's a goal to pull as much as possible ambient air into the airstream, but
the drag caused by the difference in velocity between the airstream and the surface is just a loss
of energy. If the airstream gets turbulent and stops following the curved surface, there's no more
low air pressure, no more thrust. Since all applications of a Coanda effect involve a fluid object
flowing over a solid one, the science behind this effect is known as fluid dynamics. Fluid
dynamics represents and study the motion of liquids or gases. Studying this science can lead to
many consequential discoveries like the Coanda effect.
Ground effect
Ground effect is term applied to a series of aerodynamic effects used in car design, which has
been exploited to create downforce, particularly in racing cars.
Theory
In racing cars, a designer's aim is for increased downforce, increasing grip and allowing for
greater cornering speeds. (Starting in the mid 1960s 'wings', or inverted airfoils, were routinely
used in the design of racing cars to increase downforce, but this is not ground effect.) Substantial
further downforce is available by understanding the ground to be part of the aerodynamic system
in question. This kind of ground effect is easily illustrated by taking a tarpaulin out on a windy
day and holding it close to the ground: it can be observed that when close enough to the ground
the tarp will suddenly be sucked towards the ground. This is due to Bernoulli's principle; as the
tarp gets closer to the ground, the cross sectional area available for the air passing between it and
the ground shrinks. This causes the air to accelerate and as a result pressure under the tarp drops
while the pressure on top is basically unaffected, and together this results in a net downward
force. The same principles apply to cars. The Bernoulli principle is not the only mechanic in
generating ground effect downforce. A very large part of ground effect performance comes from
taking advantage of viscosity. In the tarp example above neither the tarp nor the ground is
moving. The boundary layer between the two surfaces works to slow down the air between them
which lessens the Bernoulli Effect. However when a car moves over the ground the boundary
layer on the ground becomes helpful. In the reference frame of the car, the ground is moving
backwards at some speed. As the ground moves, it pulls on the air above it and causes it to move
faster. This enhances the Bernoulli effect and increases downforce. It is an example of Couette
flow.
Ever since the first car was manufactured in early 20 th century the attempt has been to travel at
faster speeds, in the earlier times aerodynamics was not a factor as the cars were traveling at very
slow speeds there were not any aerodynamic problems but with increase of speeds the necessity
for cars to become more streamlined resulted in structural invention such as the introduction of
the windscreen, incorporation of wheels into the body and the insetting of the headlamps into the
front of the car. This was probably the fastest developing time in automobiles history as the
majority of the work was to try and reduce the aerodynamic drag. This happened up to the early
1950‟s, where by this time the aerodynamic dray had been cut by about 45% from the early cars
such as the Silver Ghost. However, after this the levels of drag found on cars began to slowly
increase. This was due to the way that the designing was thought about. Before1950, designers
were trying to make cars as streamlined as possible to make it easier for the engine, yet they
were restricting the layout of the interior for the car. After 1950, the levels of aerodynamic drag
went up because cars were becoming more family friendly and so as a consequence the shapes
available to choose were more limited and so it was not possible to keep the low level of
aerodynamic drag. The rectangular shape made cars more purposeful for the family and so it is
fair to say that after 1950 the designing of cars was to aid the lifestyle of larger families.
Although this was a good thing for families, it didn‟t take long before the issue of aerodynamics
came back into the picture in the form of fuel economy. During the 1970‟s there was a fuel crisis
and so the demand for more economical cars became greater, which led to changes in car
aerodynamics. During the 1970‟s there was a fuel crisis and so the demand for more economical
cars became greater, which led to changes in car aerodynamics. If a car has poor aerodynamics
then the engine has to do more work to go the same distance as a car with better aerodynamics,
so if the engine is working harder it is going to need more fuel to allow the engine to do the
work, and therefore the car with the better aerodynamics uses less fuel than the other car. This
quickly led to a public demand for cars with a lower aerodynamic drag in order to be more
economical for the family.
Only about 15% of the energy from the fuel you put in
your tank gets used to move your car down the road or run useful accessories, such as air
conditioning. The rest of the energy is lost to engine and driveline inefficiencies and idling.
Therefore, the potential to improve fuel efficiency with advanced technologies is enormous.
Now a days almost all cars are manufactured aerodynamically , one misconception that everyone
has is aerodynamics is all about going faster, in a way it is true but it is not all about speed, by
designing the car aerodynamically we can reduce the friction that it encounters and there by
power needed to overcome would be less thus fuel can be saved; In the modern era where our
fuel resources are fast depleting all the efforts are to find alternate sources of energy or to save
our current resources or minimize the use of current resources like fuels, so now a days
aerodynamics are given very much importance as everyone like to have a good looking , stylish
and fuel efficient car.
AERODYNAMICS IN F1
Ask any engineer in the pit lane and they’ll tell you that the most important consideration
in F1 car design - the difference between designing a championship-challenging machine
or a tail ender - is aerodynamics.
In simple terms, F1 aerodynamicists have two primary concerns: the creation of downforce, to
help push the car's tyres onto the track and improve cornering forces; and the minimisation of
drag, a product of air resistance which acts to slow the car down.
Although always important in race car design, aerodynamics became a truly serious proposition
in the late 1960s when several teams started to experiment with the now familiar wings. Race car
wings - or aerofoils as they are sometimes known - operate on exactly the same principle as
aircraft wings, only in reverse. Air flows at different speeds over the two sides of the wing (by
having to travel different distances over its contours) and this creates a difference in pressure, a
physical rule known as Bernoulli's Principle. As this pressure tries to balance, the wing tries to
move in the direction of the low pressure. Planes use their wings to create lift, race cars use theirs
to create negative lift, better known as downforce. A modern Formula One car is capable of
developing 3.5 g lateral cornering force (three and a half times its own weight) thanks to
aerodynamic downforce. That means that, theoretically, at high speeds they could drive upside
down.
Early experiments with movable wings and high mountings led to some spectacular accidents,
and for the 1970 season regulations were introduced to limit the size and location of wings.
Evolved over time, those rules still hold largely true today.
Front wings typically have multiple elements and highly complex designs to manage
airflow
By the mid-1970s 'ground effect' downforce had been discovered. Lotus engineers found out that
by cleverly designing the underside of the car, the entire chassis could be made to act like one
giant wing which sucked the car to the road. The ultimate example of this thinking was the
Brabham BT46B, designed by Gordon Murray, which actually used a cooling fan to extract air
from a sealed area under the car, creating enormous downforce. After technical challenges from
other teams it was withdrawn after a single race. Soon after rule changes followed to limit the
benefits of 'ground effects' - firstly a ban on the skirts used to contain the low pressure area, then
later a requirement for a 'stepped floor'.
In the years that have followed aerodynamic development has been more linear, though ever
increasing speeds and various other factors have led the sport’s regulators to tweak and tighten
the regulations on several occasions.
As a result, today’s aerodynamicists have considerably less freedom than their counterparts from
the past, with strict rules dictating the height, width and location of bodywork. However, with
every additional kilogram of downforce equating to several milliseconds of lap time saved, the
teams still invest considerable amounts of time and money into wind tunnel programmes and
computational fluid dynamics (CFD) – the two main forms of aerodynamic research.
The most obvious aerodynamic devices on a Formula One car are the front and rear wings,
which together account for around 60 percent of overall downforce (with the floor responsible
for the majority of the rest). These wings are fitted with different profiles depending on the
downforce requirements of a particular track. Tight, slow circuits like Monaco require very
aggressive wing profiles to maximise downforce, whilst at high-speed circuits like Monza the
amount of wing is minimised to reduce drag and increa se speed on the long
straights.
Every single surface of a modern Formula One car, from the shape of the suspension links to that
of the driver's helmet - has its aerodynamic effects considered. This is because disrupted air,
where the flow 'separates' from the body, creates turbulence which in turn creates drag and slows
the car down. In fact, if you look closely at a modern car you will see that almost as much effort
has been spent reducing drag and managing airflow as increasing downforce - from the vertical
endplates fitted to wings to prevent vortices forming to the diffuser mounted low at the rear,
which helps to re-equalise pressure of the faster-flowing air that has passed under the car and
would otherwise create a low-pressure 'balloon' dragging at the back. But despite this, designers
can't make their cars too 'slippery', as a good supply of airflow has to be ensured to help cool the
various parts of the power unit.
The ingenuity of F1 engineers means that every now and then a loophole will be found in the
regulations and a clever aerodynamic solution will be introduced. More often than not these
devices, such as double diffusers, F-ducts and exhaust-blown diffusers, will be swiftly banned,
but one innovation that has been actively endorsed is the DRS (Drag Reduction System) rear
wing. This device, which was introduced to encourage more overtaking, allows drivers to adjust
the angle of the main plane of the rear wing to reduce drag and increase straight-line speed,
though it may only be used on specific parts of the track and when a driver is within one second
of the car ahead in a race.
Advancements in Aerodynamic Devices
Surprisingly, most teams chose not to. This is because they converged, throughout the years, to
an “endplate-less” design. They for fill the mandatory bodywork that makes up the endplate, but
actually let the front wing itself do most of the work in getting air around the tire. Still, since the
endplate has to be there, teams utilize it to help the front wing in this aspect.
Mercedes’ solution actually goes way back to its 2009 predecessor Brawn team. Just getting
started with radical aero rules changes, they came up with a unique solution of 2 smaller
endplates partly overlapping each other. That year included, Mercedes actually kept that very
same design for 3 years, with only very subtle changes. Such was the efficiency of its design.
Coming into 2012, they made changes to it, resembling more closely its current iteration:
Being remarkably simple, it does have a few functions. Air coming from the lower wing
elements gets leaked out in the gap in between the 2 endplates. The latter endplate meets up with
the last 3 front wing elements, bleeding off more high pressure at that point. The endplates bend
subtly outwards, just enough to direct air away from the wheel. Interestingly, Mercedes copied a
solution from Lotus F1, adding a small flap to the latter endplate:
Lotus came up with this solution, albeit in a slightly different form, at Spain 2013. Its purpose
isn’t completely clear, but I believe it tries to keep the faster moving air coming from the outer
edges of the first wing elements, close to the footplate, not interrupting with the slower moving
air coming from the latter wing elements, which have a higher angle of attack. That way the
higher pressure air doesn’t get sucked in the lower pressure air and avoids contact with the wheel
wake. A vortex will probably also be created at its tip, further separating the 2 flows. It’ll
probably create a little bit of lift and drag, but it should overall have a beneficial effect.
Plain Wing
The front wing itself is also a clear evolution from last
year. They kept the same amount of elements, 5, but while
only the upper element had a slot through and through,
this year the 2 upper elements are just that.
The 2 elements that have slots through and through create a vortex at their tips. Last year
Mercedes only choose to do so at the uppermost element, but this year they saw it needed to have
2 tips creating a single stronger vortex. This vortex passes along the Y250 line, a critical area for
airflow moving to the splitter and floor.
Cascades
This part has been largely overhauled since last year, yet also keeping some trademark solutions.
First of all, Mercedes dropped the r-winglet, which created a bit of downforce. Since downforce
levels have been reduced, that winglet is less needed. The R-winglet also created another vortex
along the Y250-line, but Mercedes felt a stronger vortex at the wing tips could do the job as well.
We’ll see if the r-winglet pops back up during the season.
Mercedes expanded the cascade attached to the endplate, added a J-part (yellow), added a small
vertical turning vane (blue) and twisted all vertical pieces outwards, in an aggressive attempt to
get again air away from the tires. Also note they kept the small flick at the middle plate of the
cascade (red circle) (this was the inner endplate of the cascade in 2013), as well as the IR sensor
(green).
Complete Picture
It also shows that modern front wings are just way more than downforce-production devices,
acting as complex flow conditioners to both set up airflow patterns across the car and minimizing
wheel drag.
All in all this a very detailed front wing to start the year with. I don’t see any major overhauls
coming just yet. However, with the team bound to recuperate more and more rear downforce
across the season, they will have to gain the same amount out of the front wing. Changing the
angle of attack isn’t as convenient as in the past, influencing airflow, forcing perhaps at one point
to completely overhaul the front wing. However, for now they clearly have a strong base to build
on.
Diffuser
Once the potential of using aerodynamic downforce to win races was realized, designers began
experimenting with methods other than simply attaching inverted wings. The diffuser is an area
of bodywork at the rear of the car, although the term "Diffuser" is technically incorrect, it is the
most popular term applied to this part of the car. The air flowing below the car, exits through the
diffuser on the rear of the car. The diffuser is usually find on each side of the central engine and
gearbox fairings and is, by the rules, located behind the rear axle line. Although wings and
diffusers work similarly, they are based under different concepts. A diffuser serves to eject air out
from the underside of the car. This pulling action decreases the velocity of the air below the car,
so that the more slowly moving air above the car will push the car into the ground. The suction
effect is a result of Bernoulli's equation, which states that where speed of the fluid is higher,
pressure must be lower. Therefore the pressure below the racecar must be lower than the pressure
at the outlet since the speed of the air below the racecar will be higher than the speed of the air at
the outlet. The diffuser in itself doesn't produce a reduction in pressure. Its main function is to
decrease the flow's velocity from inlet to outlet (so that at the outlet the flow velocity is similar
to the free stream velocity), with a corresponding increase in static pressure. This pressure rise
can be used to increase the flow rate through a system, as was known even in Roman times. The
diffuser can be considered to have "pumped-down" the underbody, inducing a component of
downward force on the vehicle. The pressure rise in the diffuser drives this process, so it is the
pressure-recovery behavior of the diffuser that governs the influence on an automobile. This
pressure rise is a function of the ratio of the areas at the outlet and the inlet diffuser, where this
area ratio is set by the diffuser angle and the vehicle ride height. Its design includes vertical
fences, some of which are curved, some stepped, and some angled, but all are developed through
constant tweaking and evolution in the wind tunnel. The basic job of these fences is to keep apart
the many different types of air flows found at the rear end of a racing car - areas of low pressure
air due to the rear wheels, and the rear wing, and the air coming under the floor. All these
different air flows have different energy levels and different speeds, and their separation makes
them easier to deal with. Showing precious little of the secretive diffuser, F1 rules prohibit under-
car shaping or venturis, and mandate a minimum ride height enforced by a relatively low-tech
wear plank or skidblock attached underneath the car. However, there is still scope to shape the
area directly under and behind the rear axle line.
To get around this problem, dual element or slot-gap wings are used, these allow for some of the
high pressure flow from the top surface of the wing to bleed to the lower surface of the next flap
energizing the flow. This increases the speed of the flow under the wing, increasing downforce
and reducing the boundary flow separation.
Modern F1 wing with air stream detached and stalled due to high angle of attack As airflows
over the surface of a wing increase, or angle of attack is bigger, it has a tendency to slow down
and separate from the wing. Particularly underneath the wing which runs at a lower pressure than
the top surface. This separation initially reduces efficiency by adding drag to the wing, before the
airflow totally breaks up and the wing stalls. What is very important in F-duct case is that when a
wing stalls the wing loses most of its downforce and most importantly the drag. The steeper a
wings angle, the greater chance of separation.
Gurney Flap
Flap, from aerodynamic point of view is hinged or fixed device at the trailing edge of the wing,
which can be, in majority of the cases, lowered to increase lift of the wing. The device basically
operates by increasing pressure on the pressure side of the wing, decreasing pressure on the
suction side, and helping the boundary layer flow stay attached all the way to the trailing edge on
the suction side of the airfoil. At the same time, a long wake downstream of the flap containing a
pair of counter-rotating vortices can delay or eliminate the flow separation near the trailing edge
on the upper surface (aircraft wing) or lower surface (racing car wing).
If you can reduce the drag of the car you will go faster on the straights. If you can use
the shape of the car to generate some downward pressure (usually called downforce)
onto the tires, then the car will go faster around the corners. Research into
aerodynamics has allowed cornering speeds in “high speed” corners to be much higher
than that which is possible without the use of aerodynamic aids, although it has
reduced ultimate top speeds. Track lap times have improved significantly.
REFERENCES:
1. Tune to win by Caroll Smith
2. Race Car Vehicle Dynamics by Milliken and Milliken
3. ‘Inside F1’ – www.formulaone.com
4. ‘Aerodynamics’ www.f1technical.net
5. www.wikipedia.com