Professional Documents
Culture Documents
AA 1103
Instruction Manual
1.Overview: All display segments:
Fig1
2.Power on:
Fig2 Fig3
A.Put 2 x AAA batteries in the battery compartment, slide down and hold the power button to
the “POWER” position and hold for 3 sec , the display show “ON” mode .(Fig2)
B.After “ON” , the device enter into working mode.(Fig3)
3.Power off/standby:
Fig4
Slide down and hold the power button for 3 sec to off the recorder(In 10 seconds not press
any key, will be automatically entered into standby mode).(Fig4)
4.USB Connection Interface:
5. Recording setting:
1. In a recording stop mode (start-up display), press the “FOLDER” button to select any one of
these 4( A/B/C/D ) folder for recording location,
2. The built-in microphone on the top of the recorder, it should be toward the sound source and
press “ RED “ record button and the ORANGE LED will light up, the recording starts.(Fig5)
Fig5
3. Press “ RED “ record button to pause recording.
4. Press “ RED “ record button again to make the recording start.
5. Press “ ” button to stop recording.
5.1. Display the remaining recording time
1. In stop mode press the “ stop ” button. The remaining recording time
in the memory is shown in hours and minutes.
5.2.Telephone recording:
please follow the below connection picture, press “REC” to start telephone recording after finish
connection:(the record and playback method are the same as normal recording)
6. Playback setting:
6.1 Select a recording folder:
1. In standby mode, press the “ FOLDER “ button to select one of these 4 folder( )
for the recording location.
2. In the stopped mode, press the button “ ” and that button ” ” to select the record of the
recording file.
6.2 Playback:
1. If you playback the recording file, please follow the 6.1 step to select a recording file
2. Press to playback the selected file. During it playback, the recording time can show on
the display.(Fig6).
Fig6
3. Press “+ /– “buttons to adjust the sound volume, press “MENU” return to playing mode...
4. Press key to pause playback, press again to continue..
5. Press the stop key to stop playback.
1. In playing state, Press and hold “ “ button at least 3 sec during playback.
2. Press + / – to select the desired playback speed from -8 to +8.
3. Press the “ RED “ record button to confirm playback speed.
6.4 Repeat playback:
In playing state, press “MENU” first, then press “ ” to select “repeat one”, “repeat all”,
“no repeat”, Press the “ RED “record key to confirm.
– no repeat
– repeat folder playback
– repeat one file
6.4.1 A-B repeat playback:
In the playing state, press “FOLDER” to set the repeat playback, now “ ” will flash to starting
time, press “FOLDER” again to set the end time “ ”stop flashing, then playback only repeat in
between starting time and end time.
Press “FOLDER” to cancel A-B repeat and back to normal playing.
6.4.2 T-MARK:
In the playing state, press “T-MARK” to set the first index mark, press “T-MARK” again to set the
second, third ,...till the tenth mark...
Each recording file can be set 10 index marks at maximum.
Press and hold “T-MARK” can show out all location to be marked by T-mark symbol.
Then press “ ” to select which T-mark want to start playing..
press “RED” button to play each T-mark set, press “FOLDER” to delete each “T-mark”...
7. Delete:
In standby mode, select the folder and file you want to delete with
Press and hold “T-MARK” to enter into delete menu.
The display will show “ ”, Press to select delete one or delete all-- ..
8. Settings:
In standby mode, Press and hold “MENU” for 3 seconds to enter into the Settings, then press
“ ” go into each set up in the setting.(press “ ” button to go out of the set up).
Note: Under set up processing, Press “ ” will cancel the set up without saving and return to the
standby mode..
8.1 (MODE)Setting recording quality:
This setting can adjust the sensitivity, cut background noises to adapt to the environment.
Press to select the recording quality. The selected microphone/recording sensitivity
symbol is shown on the display:
H – high sensitivity
L – low sensitivity
Press the “RED” key to confirm.
Press the ” ” stop key to exit the menu.
If voice-activated recording(VOR) is in “ON” mode, the recording only start when the device
detect voice from the line-in jack( microphone symbol ), the recording pause if no any voice to be
detected, it will continue to record once detect any voice .
Press to switch ON or OFF, to enable/disable voice activation(VOR).
Press “REC” key to confirm the selection. If the voice activation is in “ ON “ mode, the screen will
display .
Press the ” ” stop key to exit the menu,
8.7 (AUTO-OFF):
The device is power off automatically if no any operation within a period of time (the time can be
adjusted by the button ).
.Press the button to select 5, 15, 30 or 60 minutes.
Press the “REC” key to confirm.
Press the ” ” stop key to exit the menu,
This feature can delete all data and files if it is in “YES” mode.
This function can divide very longtime recordings into some parts, if the recording for a meeting
very long, the user can set time a stop point and start point for a new recording, default setting
include OFF, 30mins or 60mins.
Press , to select 30mins, 60 mins, or switch the feature to OFF.
Press the “REC” key to confirm.
Press the ” ” stop key to exit the menu,
Press to select the function. The remaining memory space display in megabytes .