Professional Documents
Culture Documents
3. Pipes and
Fittings 5 3 2 10 25 %
4. Procedures in
installing pipes
3 1 10 14 35 %
and fittings
19 9 12
TOTAL 40 100 %
Prepared by:
_____________________
MARY JEAN O. DALIDA
Trainer
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 1 of 10
units and assemblies
MARY JEAN O. DALIDA
SAMPLE TEST QUESTIONS
l. MULTIPLE CHOICE:
Instructions: Choose the letter of the best answer from the given choices.
Write the letter of your choice on your answer sheet.
2.These are primarily used on galvanized steel and iron pipe and on heavy-
duty fixtures with rough finishes, such as outdoor spigots or hydrants.
A. Channel-Type Pliers
B. Faucet Packing, Washers and O-rings
C. Toilet or Closet Auger
D. Tubbing Cutter
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 2 of 10
units and assemblies
MARY JEAN O. DALIDA
5. These are used for fixing leaky valves on sinks, radiators, and other old or
traditional equipment.
A. Channel-Type Pliers
B. Faucet Packing, Washers and O-rings
C. Toilet or Closet Auger
D. Tubbing Cutter
6. It has a long metal rod with a bend for reaching into the hole at the
bottom of the toilet bowl.
A. Channel-Type Pliers
B. Faucet Packing, Washers and O-rings
C. Toilet or Closet Auger
D. Tubbing Cutter
7. These are commonly known by the brand name Channel-Locks, and are
also known as slip-joint pliers.
A. Channel-Type Pliers
B. Faucet Packing, Washers and O-rings
C. Toilet or Closet Auger
D. Tubbing Cutter
9. This may be the most common plumbing tool in the home. It has a rubber
cup-like shape and a wooden handle and is used to clear clogs in sinks, tubs,
and showers.
A. Channel-Type Pliers
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 3 of 10
units and assemblies
MARY JEAN O. DALIDA
B. Cup Plunger
C. Flange Plunger
D. Flange Plunger
A. Channel-Type Pliers
B. Cup Plunger
C. Flange Plunger
D. Flange Plunger
Instructions: Match the images in column A with the appropriate PPE on column B.
Select your answers from the choices inside the box below. Write its protection on the
space provided.
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 4 of 10
units and assemblies
MARY JEAN O. DALIDA
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 5 of 10
units and assemblies
MARY JEAN O. DALIDA
II-B. TRUE OR FALSE TEST:
Instructions: Tell whether the given statements about Work Plan is true or false. Write
(T) if the statement is true and (F) if the statement is false. Write your answer in the
separate sheet of paper.
1. Safety helmet refers to masks and filters you can wear over your face or under other
gear like face fields and ear muffs.
2. All personnel handling rough, sharp and excessive coarse material such as
reinforcement bars, rods, pre-cast concrete, toxic, electric and hot materials shall be
protected by safety gloves.
5. Site Engineers and all construction personnel involved in site activities should wear a
safety helmet or hard hat before entering the work site and it should be wear at all
times.
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 6 of 10
units and assemblies
MARY JEAN O. DALIDA
III- IDENTIFICATION TEST:
________4. It is a kind of pipe fitting that is used in the place where four
pipes meet together.
________6. It is used when pipes pass through walls, ceilings & floors.
________8. Short sections of pipes that are male threaded & used for
connecting 2 female threaded pipe ends fittings.
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 7 of 10
units and assemblies
MARY JEAN O. DALIDA
IV- PERFORMANCE TASK
CRITERIA
DID I…? YES NO
Remove old drainpipe
- remove the old drainpipe assembly from the top down use
your pliers to unscrew any stubborn slip nuts.
Add T-Fitting
- add the t-fitting with slip washers and nuts then apply pipe
lubricant on the slip washer to ensure a tighter fit.
ANSWER KEY:
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 8 of 10
units and assemblies
MARY JEAN O. DALIDA
I. MULTIPLE CHOICE
1. B
2. A
3. D
4. D
5. B
6. C
7. A
8. C
9. B
10. D
III IDENTIFICATION
1. Trap Fittings
2. Elbow Fittings
3. Union Fittings
4. Cross Fittings
5. Plug Fittings
6. Flange Fittings
7. Tee & Wye Fittings
8. Nipple Fittings
9. Coupling & Adapter Fittings
10. Valves in Pipe Fittings
IV PERFORMANCE TASK
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 9 of 10
units and assemblies
MARY JEAN O. DALIDA
TITLE: Perform the procedures on How to Install/Replace Kitchen Sink Trap
CRITERIA
DID I…? YES NO
Remove old drainpipe
- remove the old drainpipe assembly from the top down use
your pliers to unscrew any stubborn slip nuts.
Add T-Fitting
- add the t-fitting with slip washers and nuts then apply pipe
lubricant on the slip washer to ensure a tighter fit.
Comment/ Recommendations:
[Type text]
Date Developed: Document No.
PLUMBING NC II Issued by:
June 2022
Performing multiple plumbing Compiled by: Page 10 of 10
units and assemblies
MARY JEAN O. DALIDA