Professional Documents
Culture Documents
Router Tools Cutting Tools Brazing & Sawfiling Hand Tools Information
SHOP BY BRAND
ATA Tools
Bessey Tools
Bondhus
Bormax-Famag
Carbide Processors
Chapman MFG Co
Clamp MFG Co
Edge Eyewear With dozens of drill bit types and thousands of sizes to choose from we'll explain the differences and help you choose the right drill
Felo bit for your application.
SALES AND SPECIALS Drill Bits - Normally used with hand held drills or drill presses fitted with standard chucks. These machines use a key to tighten
or loosen the clamping mechanism.
Sale Boring Machine Bits - Typically used in automated machinery such as drill banks or CNC machines fitted with tool holders or
Contests and Promotions single size collets. These machines require tools to assemble and disassemble the clamping mechanism. Many boring
machine bits are available in right or left hand rotation.
Closeout Clearance
*Note that most standard drill bits can be used in automated machinery Want(with exclusive deals?
the proper adapter) and most boring machine bits can be ×
Great Gift Ideas used in a portable drill or drill press (assuming the chuck is big enough). We have
Be the only
first to organized
know aboutthem in this
special fashion to make selection
offers
Deal of the Day easier.
Tool Sets
Bradpoints are also used for thru-holes in CNC applications where a conventional drill point would penetrate the table below
Woodworking Fences the panel. Bradpoints have spurs on the outer edges to prevent splintering and chipping of the surface material as well as a
center spur to prevent walking as the bit penetrates the surface.
OUR NEWSLETTER Fishtail Point: These special drill points form a reverse "V" in the tip and are designed for drilling into a
surface at an angle without walking. They are commonly used as center drills in counterbores for furniture assembly where
Full Name
panels must be joined at right angles.
Email Address
Taper Point: These drill bits have a very large taper, extending far up the drill which creates a tapered hole.
Shank Styles: Twist drill bits designed for use in automated machinery have fixed diameter (usually 1/2" or 10mm) shanks, threaded
shanks, or specialty shanks designed for certain machines. General purpose twist drills for use in portable drills have shanks the
same diameter as the bit size (up to a certain diameter), larger diameter bits incorporate a reduced shank (either 1/4", 3/8" or 1/2")
to fit into a standard drill chuck. Some bits have 3 flats on the shank to prevent spinning under high torque loads. Others have 1/4"
hex shanks for use in a portable drill with a hex bit holder.
Materials: General purpose twist drills for use in portable drills are available in different grades of high speed steel as well as cobalt
steel and solid carbide. Twist drill bits for automated machinery are available in carbon steel, high speed steel, carbide tipped, and
Want exclusive deals? ×
solid carbide.
Be the first to know about special offers
Coatings: General purpose drill bits are available with black oxide, bronze oxide, a combination of black and bronze oxide, and TiN
Your
coatings. Twist drills for automated machinery on our site are primarily foremail
use inaddress Sign Up
wood or plastics and are not coated.
Counterbore Drill Bits
General Description: Counterbore drill bits create a flat bottom blind hole with a smaller diameter center hole that penetrates
through the material. The purpose of a counterbore is usually to conceal the fastener head (by covering the hole) or provide a recess
to prevent the fastener from protruding above the surface of the material being drilled. Counterbores on our site are designed for
use in wood or plastics and are not intended for counterboring steel.
Tip Styles: The cutting tip of a counterbore drill consists of one or more flat blades extending from the center drill to the outer edge.
Counterbores are available with or without spurs (teeth) at the outer diameter of the bit. Counterbores with spurs on the outer edge
prevent chipping and splintering on wood or laminated surfaces.
Flute Styles: Some counterbores do not have flutes (except for the center drill) and simply shave away the material, others are
designed similar to a twist drill with no tip angle and a replaceable center drill.
Shank Styles: Counterbores for use in hand-held drills typically clamp on to a standard twist drill and therefore have a straight shank
the same diameter as the center drill. Counterbores for use in automated machinery have fixed diameter (usually 1/2" or 10mm)
shanks, threaded shanks, or specialty shanks designed for certain machines.
Materials: Counterbores are available in Carbon Steel, High Speed Steel, or Carbide Tipped
Tip Styles: The cutting tip of a countersink drill consists of two or more flat blades extending from the center drill to the outer edge.
Countersinks are made with angles from 60 to 120 degrees but those on our site are typically 82 or 90 degrees. For wood use many
times the manufacturer does not specify the angle.
Flute Styles: Some countersinks do not have flutes (except for the center drill) and simply shave away the material, others are
designed similar to a twist drill with a replaceable center drill.
Shank Styles: Countersinks for use in hand-held drills typically clamp on to a standard twist drill and therefore have a straight shank
the same diameter as the center drill (some have 1/4" hex shanks for hand use in a bit holding screwdriver). Countersinks for use in
automated machinery have fixed diameter (usually 1/2" or 10mm) shanks, threaded shanks, or specialty shanks designed for
certain types of machines.
Materials: Countersinks are available in Carbon Steel, High Speed Steel, or Carbide Tipped
Forstner Bits
Three Wing Drills
Door Hinge Bits
Mortising Bits
Spade Bits
Tip Styles: The cutting tip of a flat bottom boring drill consists of one or more flat blades extending from the center to the outer
edge. Flat bottom boring bits are available with or without spurs (teeth) at the outer diameter of the bit. Bits with spurs on the outer
edge prevent chipping and splintering on wood or laminated surfaces. Some flat bottom boring bits also include a center spur to
keep the bit from walking during the initial cut - Spade bits are a good example.
Flute Styles: Large flat bottom boring bits do not have flutes, they consist of only the cutting surface and the chips remain in the
hole until the bit is removed.
Shank Styles: Most large flat bottom boring bits have a fixed size hexagonal shank. The hex shank prevents the bit from spinning in
the chuck under excessive loads. Want exclusive deals? ×
Be the first to know about special offers
Materials: Flat bottom boring bits are available in Carbon Steel, High Speed Steel, or Carbide Tipped.
Your email address Sign Up
Coatings: Flat bottom boring bits on our site do not contain special coatings.
Specialty Drill Bits
General Description: Specialty drill bits are any bit that doesn't fall into one of the four categories above. These bits include:
Plug Cutters - Essentially a hole saw without a center drill, these bits are designed to cut round plugs from
lumber or other stock that are used to fill a counterbore after fastening the parts. After gluing the plug into the counterbore,
the plug is then cut and sanded flush to conceal the hole. Plug cutter bits are measured by their inside diameter (the size of
the plug that will be left) and are not meant to drill completely through the stock. Instead, the stock is drilled to a depth slightly
deeper than the hole to be filled and the plug is popped out using a small screwdriver or other tool. Plug cutters are almost
always used in a hand held drill.
Glass and Tile Drills - Used to drill holes (usually for fasteners) in non-tempered glass, tile, and similar
materials. These bits feature carbide tips and straight shanks that can be used in either hand drills or automated machinery.
Masonry Drills - Used to drill holes in concrete, brick, etc. using a special "hammer drill" which pounds the
drill bit as it rotates. A threaded anchor is usually installed if the hole is to be used to attach objects to the surface. Masonry
drills have carbide tips and either standard or high helix flutes depending on the intended use. They are typically coated with
black oxide to prevent corrosion and feature shanks that are either the same size as the bit or reduced diameter to fit the
portable drill chuck.
Augers - Designed to bore somewhat large holes deeply into wood or other similar materials. Auger tips
feature a protruding tapered screw that helps to pull the bit into the wood with one or two cutting edges similar to a
counterbore and may include outer spurs. The flutes of an auger drill bit are extra large to pull the chips up and out of the hole.
Augers are normally used in hand held drills and the shank may be round or hexagonal.
Annular Cutters - Used to drill larger thru-holes in metal (7/16" and up), these bits require a special
machine. Similar to a hole saw, annular cutter bits cut the outer diameter of the hole and leave a solid center slug. This creates
a much more efficient drilling process with burr-free holes in tubing, sheet metal and iron bar stock. Annular cutter bits on our
site are made from Cobalt High Speed Steel.
HOME
PRODUCTS
SERVICES
ABOUT US
SITEMAP
REVIEWS SITEMAP
CONTACT US:1(800)346-8274
All prices are in USD Copyright 2022 Carbide Processors. Sitemap | Website by oBundle