Professional Documents
Culture Documents
Manual
Issue 1.0
A80 Amplifier
P80 Power Amplifier
ARCAM
Bringing music & movies to life
Contents List
! Circuit description
o A80/P80
! Technical specifications
! Circuit diagrams
o L943AY
! Transformers
o L916TX – 115/230VAC toroidal
o L917TX – 100VAC toroidal
o L907TX – 100VAC frame
The mains input to the unit is supplied at SK200 and is Supply Related components
filtered the Y Caps and locations C200 /C201 and X + 45v L Left power amp positive rail.
cap at location C209, these are in-place to reduce + 45v R Right power amp positive rail.
mains born HF interference and to prevent bridge - 45v L Left power amp negative rail.
rectifier noise from leaving the unit. - 45v R Right power amp negative rail.
- 38v VFD Display cathode rail derived from –45v(R)
The mains select switch at location SW200 works in +15v (A) IC 300, 301, 302, 303, 304, 305, 306,
conjunction with the dual primaries on the 115/230v 307, 308, 309 also including the input
transformers, the switch allows for the units to be used clamp diodes all within the pre-amp stage.
in territories running a 115v or 230v grid when the - 15v (A) IC 300, 301, 302, 303, 304, 305, 306,
switch is set to the 115v position the primary windings 307, 308, 309 also including the input
are connected in parallel. clamp diodes all within the pre-amp stage.
+ 5v (A) IC309 volume control
Fig 1. Fuse value information. +4.8 (D) Input trigger stages, signal detect IC700,
delayed off IC703, IC701. Main micro
Fuse location. Value. IC600.Remote pickup, Master reset
FS200 T2.5A (20mm) IC601, Over current detect-AC detect –
FS201 T2.5A (20mm) thermal cut-out IC600
FS200 (100v) T3.15A (20mm) Fil 1/Fil 2 3.3v~ filament supply.
FS201 (100v) T3.15A (20mm)
FS202 (s.m standby 9v a.c rms) T500mA (s.m)
FS203 (D.C inline) T2.0A (20mm) Pre-amp.
FS204 (D.C inline) T2.0A (20mm)
The A80 Pre-amp has inputs for Phono, Aux, CD, Tuner,
The standby Transformer TX200 continuously powers AV, DVD and Tape. All inputs except Phono have a simple
the digital circuitry (+4.8v(D)) when power is resistor-capacitor 340Khz low pass filter to remove any
connected to the unit, this supply powers the Micro via unwanted high frequency noise from the input signal/local
a regulating circuit based around regulator REG 201 area, a pair of diodes on each input connected to the
special mention should be made of fuse FS202 as any +15/-15v rails prevent damage to the CMOS input
interruption to this supply will render the unit switching chips at locations IC300 and IC301, if any offset
completely lifeless and as such this circuit should be is seen at the input the switching chips on a given input we
checked before inspecting any other areas of the may suspect the failure of one of the input diodes.
board.
Fig 3. Logic status of IC302 and 303 (switching chip).
We will see that the main power transformer TX200
supplies a separate secondary winding for the +15 and Low= 0V High=4.8 (Cmos).
–15v analogue regulation stages via the two fuses at Input. A0 (pin 1) A1 (pin 16) A2 (pin 15)
Phono Low Low Low
board locations FS203 and FS204, the failure of either
of these fuses will cause the op-amps connected to the Aux Low High Low
regulated rails to swing D.C. The regulator at location CD High High Low
REG 200 regulates the +15 rail and intern supplies the Tuner Low Low High
+5V(A) analogue supply via the reference Zener at AV High Low High
location DZ200 and drive transistor TR200. DVD Low High High
Tape High Low Low
The high level power amp A.C supplies arrive at
Con204 as a 4-wire supply this allows us to implement
a dual bridge network circuit with 4 individually The outputs of IC300 (L) and IC301(R) can be seen on pin
smoothed D.C rails these are labelled as +45(L), 8 as a current signal and such this can not be viewed via
+45(R) and -45(L), -45(R) we pull a –38v rail from this CRO although a 100 ohm resistor inline with the scope
point to form the VFD cathode bias voltage via R211 probe may yield some results, from here we drive into line
Con205 delivers the 3.3 V A.C supply to the main drive op-amp IC307 (L) and IC308 (R) signal can be seen
board and then onto the display VFD via R203 (2R2 at the output pin (1) and travelling into the volume control
f.u). chip (IC309) on pins 16 (L) and 9 (R) the output from the
Volume control is driven into IC307 at pin 6 (L) and IC308
pin 6 (R) and seen again on pins 7 on both IC307 and
IC308. After the Con 302 and Con 303 we drive directly
Into the power amp stages but from this point we can The transistors found at locations TR400 and
configure the unit as a separate Pre amp/Power amp TR401/TR402 form the PNP Wilson mirrors and TR416
by moving the jumpers to the pin 2 and 3 of Con 304 and TR411/TR417 form the Wilson NPN current mirrors,
and Con 305, and then remove the jumpers at Con emitter degeneration is provided by R405, R406 (+) and
302 and Con 303 this may also be of use when fault R407, R408 (-).
finding as we can effectively isolate the and D.C
offset/distortion problems coming from the Pre amp R415 and R416 decouple the current mirror stages from
stage to the power amp stages and test these stages the main power supply stages to allow the bootstrap circuit
as a separate entity. to operate this circuit is formed by C423 and C424 and the
Metal film 1 watt resistors at locations R452/R453, the
The Pre amp power up mute and power down mute is boots strap is provided to allow the output stage rails to go
controlled by the relay at location RLY300 A/B the up and down slightly with the output signal to the
relay also triggers to mute the switching noise when loudspeaker, this enables the driver stage to fully saturate
switching between inputs (see micro control/protection the output drivers giving the greatest output and the best
and display section). thermal efficiency.
Power amp stages. TR405 and TR407 are the Pre-drivers, TR412/TR414 and
R411/R434 provide a current limit of about 30mA under
The main power amplifiers are of a Class A/B design fault conditions. R423 and R428 loosely couple the
which use SAP “audio” transistors in a asymmetrical outputs of the output drivers to the inputs of the SAP
current feedback configuration, Input and feedback output devices, this allows the output devices inbuilt
paths are D.C coupled and there is a active integrating temperature sensing diodes to accurately control the
servo to remove D.C offsets from the outputs. quiescent current of the output drivers as the temperature
varies, C425 and C405 ensure that both halves of the
The basic principle of operation is as follows: Left output stage receive an equal A.C component.
channel description given only, read all references as
5xx for the right channel. The output transistors are TR413 and TR415 these are
specially designed for audio power use Sanken SAP15N
The input level of the power amp stage is clamped by and SAP15P devices they provide a inbuilt 0W22 thick film
the 3V9 zener diodes at positions DZ402 and DZ403 power resistor and temperature sensing diodes that track
this protects the power amp input stages from gross the VBE versus temperature characteristics of the power
overload and subsequent damage R410 and R402 and transistors allowing for accurate control of the quiescent
C416 in parallel form a 340khz filter. current.
IC400A is a V-I converter with a gain of 2 it’s output R459 and C427 form the Zobel network which is provided
will be a accurate amplification of it’s input voltage (i.e to ensure that the amplifier see a constant and resistive
the output voltage at pin 1 will be identical to the input load at high frequencies C421 locally couples the “High
at pin 3 but twice the amplitude) the output voltage is frequency” and signal grounds together at the input stage
driven unto a 44 ohm load formed by R445 and R446 for the same reason. Any signs of burning or scorching of
this op-amp is used in a slightly unusual configuration R459 will indicate that the unit amplifier channel(s) have
in that it’s power supply pins are used as a current been running unstable or oscillating.
output and the output pin is used as a current
feedback. Transistors TR404 and TR408 supply the +/- The Bias should be set for minimum distortion (THD+N)
15v rails and act as cascades to pass it’s supply pin using a 0.5v rms 20 Khz sine wave into the CD input with
currents through to the current mirrors. the amplifier set for full gain, the absolute maximum level
of Bias acceptable is 22mV measure across CON401 (L)
The “feedback current” flows back from the power amp or CON 501 (R) the adjustment is made using RV400 and
output via R447-R450 to allow IC400A to swing it’s RV500 we set the bias at the factory using an extremely
output, this is why the term current feedback is used – accurate Audio Precision-audio analyser.
it’s is the current flowing in the feedback resistors that
sets the overall gain of the amplifier. If you do not have access to a distortion level meter
capable of 0.05% or better accuracy you may be able to
IC400B acts as an inverting integrator and it’s purpose rough set the amplifier to a typical reading of 15mV (at
is to remove DC from the loudspeaker outputs. Any cold switch on).
positive D.C offset will cause the output of IC400B to
go negative thus increasing the current in it’s negative
supply pin and pulling the output voltage back to zero
R420 and C442 set the time constant of the integrator
so that audio frequencies are ignored
Fig 4. Suggested blanket replacement parts for Micro control/protection and display.
power amp failures.
Location Description Model Part no. The micro is tasked with providing an instantaneous safe
TR413 Output driver + SAP15NY 4CSAP15N operating area for both the amplifier and loudspeaker by
TR415 Output driver - SAP15PY 4CSAP15P monitoring the below areas.
TR410 Predriver + FMMT 497 4AFMMT497
TR412 Predriver + ZDT 6758 4AZDT6758
TR414 Predriver - ZDT 758 4AZDT758 o D.C at both left and right channel outputs.
TR405 Predriver - FMMT 597 4AFMMT597 o Over current within either power amp stage.
TR401 Current mirror PNP BC859B 4A859 o Over temp detection for both power amp stages.
TR402 Current mirror PNP FMMT 597 4AFMMT597 o A.C present detection.
TR411 Current mirror NPN FMMT 497 4AFMMT497
TR417 Current mirror NPN BC849B 4A849B Please see fig 5. For voltage readings with regards to the protection
TR412 Driver bias + ZDT 6758 4AZDT758 operations.
The Micro has direct control over all internal relays for Con 400 and Con 500 are for the Bias setting and should
protection and output control, the speaker relay control not be altered, if in doubt you should not measure more
lines can be seen on the diagram as SPKR1 for SP1 than 22mV across Con 401 and Con 501 when the
and the SPKR2 for SP2 outputs, these lines switch amplifier is idle and this should be adjustable using RV400
High to engage the relay. and RV500 (L&R channels).
The A80 pre-amp relay should disengage when Con 601 and Con 602 are for re-programming (move the
switching inputs to prevent any chip switching noise jumper from Con 601 to Con 602 when reprogramming
from leaving the pre-amp stage the control line can be otherwise the jumper should be on Con 601).
seen on R385 and switches High to engage the relay.
Con 700 and Con 701 are used to set the P80 signal
detect sensitivity as default the link is fitted giving a input
Signal Detect and Delayed off – P80 only. sensitivity of roughly ~500uV if the jumpers are removed
the sensitivity decreases roughly x4 to 2mV this setting
Signal detection is achieved by amplifying the signal can be used for operation with noisy source equipment.
present at the power amp inputs by a large amount
using two channels of a quad op-amp at location Con 702 is used to set the time coefficient of the auto
IC700 A/B the outputs of this op-amp are summed by power off delay, the default pins are 1 & 2 this gives a
a non-inverting comparator formed using the two delay of 12 minutes until the amp powers down under a no
remaining op-amp channels these will produce a active signal period, if we place the jumpers on pin 2 & 3 this
High reset pulse at the output pin 14. time increases to 45 minutes +/- 20%.
When mains is plugged into the P80, the master Fig 8. Jumper settings.
*Reset line goes low and the 0.38Hz clock starts
ticking. The *Reset pulse resets the latch effecting a Jumper A80 P80
HIGH *Q output and thus a LOW circuit output. When Con 300, Con 301 Not fitted Fitted
Con 302, Con303 Fit (NF for pre/pwr) Not fitted
the signal detect Latch and Counter Reset go HIGH Con 304, Con 305 1&2 (2&3 for Not fitted
(an input is detected), the *SD latch input is driven pre/pwr)
LOW by the inverter and *Q goes LOW the circuit Con 306, Con 307 1&2Phono;(2&3 Not fitted
output then goes high switching the Amplifier on. Aux2)
Con 400,Con 500 Factory set Factory set
Con 601 Fit (NF to program) Not fitted
Con 602 Fit (NF to program) Not fitted
Con 700, Con 701 Not fitted Fit (0.5mv), NF (2mV)
Con 702 Not fitted 1&2 (12 mins; 2&3
45mins).
Fig 9. Major components pin identification.
1=Collector 1
2=Collector 1
3=Collector 2
4=Collector 2
5=Emitter 2
6=Base 2
7=Emitter 1
8=Base 1
TLO 72
FMMT 497/597
NJM2114
BC849/BC859
1=Base
2=Emitter
3=Collector
DG408DY
1=Anode
2=Cathode
3=Common connection
74HC00D
ITEM101 1 F205 Tape D/Sided 12MM X 70MM DS Polyester 4965 Placed between VFD and PCB; NF ON P80
ITEM104 4 F232 13/16 inch O-Ring Rubber O-Rings fitted over main power supply caps
R100
+45V_L GENERAL NOTES
5R6
Power Amp Left
2W
L943C4_5.1.SCH
CF This is the Master Schematic for A80 (L943AY) and P80 (L944AY) PCB
+45V_L RLY100A
FIX100 FIX101 FIX102 FIX103 FIX104 Omron
assemblies. Any changes to the schematics in this document must be
Dia 3.5mm Dia 3.5mm Dia 3.5mm Dia 3.5mm Dia 3.2mm PRE_OUT_L VIPROT_L
L100 G5Z-2AE reflected in the relevant child documents.
OUTPUT_L RLY101A
1 P101 2U2
Omron
0V_FB_L
0V_FB_L
0V_LS_L
0V_HF_L
G5Z-2AE When generating BOMs for L943AY or L944AY, ensure that the relevant
C101
-45V_L
components are fitted or not fitted (those with "NF" or "FIT" in the nearby text).
100N
50V -45V_L
0805 0V_HF_L
0V_LS_L
These schematics follow a simple heirarchy scheme. Sheet symbols on the top
0V(D) sheet represent a child or sub-sheet. Net labels on sub-sheets are local or
Power Supplies
specific to that sheet. Ports on the sub-sheets connect to sheet entries on
LS101 Right Outputs
G P PRECISION
the parent sheet, where they are connected together.
Primary power nets are denoted by type in parenthesis, e.g. 0V(D).
+45V_R
R101 Secondary nets are denoted by underscores, e.g. 0V_LS_L.
5R6
Power Amp Right
2W
L943C5_5.1.SCH
CF To perform an electrical rule check or synchronise with the PCB, set Net
+45V_R RLY100B
Power Supplies
L943C2_5.1.SCH Omron
Identifier Scope to Sheet Symbols/Port Connections.
PRE_OUT_R VIPROT_R
9VRMS L101 G5Z-2AE
9VRMS
+4.8V(D)
+4.8V(D) OUTPUT_R RLY101B
PWR_ON 2U2
+45V_R Omron
+45V_R 0V_LS_R
+45V_L 0V_FB_R G5Z-2AE
+45V_L 0V_FB_R 0V_HF_R
0V(D)
0V(D)
0V_LS_L
0V_LS_L
-45V_R HEADPHONE OUTPUT & MUTE
0V_HF_L -45V_R (NF ON P80)
0V_HF_L
0V_FB_L 0V_HF_R
0V_FB_L NF
0V(SIG) 0V_LS_R
0V(SIG) R102 0R0
0V(SIG_2)
0V(SIG_2)
0W125 0805
0V_FB_R
0V_FB_R
0V_HF_R R105 R104 RLY102A
0V_HF_R
0V_LS_R 330R 330R R106 NEC
0V_LS_R
1W 1W 100R EB2-5NU
0V(PSU)
+45V_L CF CF 1W NF
+4.8V(D) CF R103 0R0
0V(D) NCL SKT100
-45V_L
-45V_L 0W125 0805
-45V_R
-45V_R RLY102B
A80/P80 Protection & Micros R107 CL
-38V_VFD L943C6_5.1.SCH CON100 CON101 100R NEC
-38V_VFD
FIL_1 Q106 1 1 Q113 1W EB2-5NU 2 L
FIL_1 OUTPUT_L
FIL_2 Q111 2 2 Q114 CF 3 R
FIL_2 OUTPUT_R
Q118 3 3 Q115 1
+15V(A) Q121 4 4 Q116 CR
+15V(A)
+5V(A) +45V_L Q125 5 5 Q117
+5V(A) +45V_L RLY102C D102
+45V_R
+45V_R NEC BAS16
-15V(A) +4.8V(D) AMP AMP NCR
-15V(A) +4.8V(D) EB2-5NU SOT-323
0V(D) CT CT HOSIDEN
0V(D) 0.38Hz_CLK
HLJ
PreAmp Controls
0V(SIG)
0V(SIG)
-45V_L
-45V_L
-38V_VFD
-38V_VFD
FIL_1
FIL_1
FIL_2 A80 Trigger, RC5 & P80 Sig Detect
FIL_2
A80 PreAmp L943C7_5.1.SCH
SPKR2_ON
L943C3_5.1.SCH TAPE_0
TAPE_0 SPKR1_ON +45V_L
TAPE_1
0V_PREOUT TAPE_1 +4.8V(D) REMOTE_P
TAPE_2
TAPE_2 PWR_ON 0V(D) REMOTE_N
VOL_SCLK
*PRE_MUTE
*PRE_MUTE 0V(SER)
VOL_SCLK
0V_SER
0V_CHASS TRIG_IN OUTPUT MUTING
0V(D) VOL_SDATA
0V_D_PRE VOL_SDATA 0.38Hz_CLK
*RESET *RESET
TAPE_0 LISTEN_0
TAPE_0 LISTEN_0
TAPE_1 LISTEN_1
TAPE_1 LISTEN_1 PRE_OUT_L
TAPE_2 LISTEN_2
TAPE_2 LISTEN_2 0V_PREOUT D100 D101
+4.8V_D_PRE PRE_OUT_R RLY100C RLY101C
VOL_SCLK 0V(D) 1N4003 Omron Omron 1N4003
VOL_SCLK 0V_D_PRE DO-41 DO-41
0V(SER) *PRE_MUTE G5Z-2AE G5Z-2AE
0V_SER *PRE_MUTE
VOL_SDATA VOL_*CS
VOL_SDATA VOL_*CS
VOL_*CS
VOL_*CS VIPROT_L
VIPROT_R
9VRMS
9VRMS
LISTEN_0
LISTEN_0 R108 220R TR100 TR101
LISTEN_1 SPKR2_ON
LISTEN_1 REMOTE_P BD179 BD179
LISTEN_2
LISTEN_2 REMOTE_N 0W25 MF TO-126 TO-126
TRIG_IN
+15V(A)
+15V(A) R109 220R
+5V(A) SPKR1_ON
+5V(A)
+4.8V_D_PRE 0W25 MF
*PRE_RLY R110 R112 R111 R113
0V(SIG) 220R 2K2 220R 2K2
0V(SIG)
0V(SIG_2) 0W25 0W125 0W25 0W125
0V(SIG_2)
-15V(A) MF 0805 MF 0805
-15V(A)
PRE_OUT_L
PRE_OUT_R R114
0R0
0W25
MF
+45V_L
0V(D)
Flexfoil
DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
A80/P80 - Top Level Sheet 03_E230 MJT 04 Aug 03
Changed P80 s/w & fitted IC socket for IC603 (P80 only).
5.0
Display snapoff fixing holes reduced to 3.2mm
Filename: L943C1_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
23425 Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 1 of 8 DRAWING NO. L943C1
ITEM203 1 F006 Clip For SW Profile Heatsink
1 TX200 5
9VRMS
D214
SH200 BAS16
EMC Shield NF SOT-323
115V 9V
SKT200
C200 +4.8V(D)
2A
2B
3N3
2
N REG201 +4.8V(D)
250V 2 6 LM317T
E CER EARTH C209
220N 115V 230V
3 7
FS202 +4.8V(D) RLY200C
R218 D215
ADJ
L C201 275V Takamisawa
FS200 T500mA 220R BAS16
3N3 PP X2 F1CA005V
1A
1B
1
T2.5A R452 0W25 SOT-323
250V C221 TO-220
S506 MF
BULGIN CER 100N HS201A
SW200 115V 9V 100V
PX0580 DBR203 SW50-2 R219
1 FS201 FHLDR200 MKS2 C226
18-000-0019 20mm HLDR 8.8C/W 22R 1000UF
T2.5A 3BDF01M
S506 C225 0W125 10V
4 8 YK
1000UF 0805 R216 P202 TR202
PCB Mount Frame PWR_ON FMMT497
This EMC can should now not appear FHLDR201 25V
20mm HLDR 7A9301 R217 2K2 SOT-23
on any BoM as there is a safety LIVE YK
issue regarding the can shorting to a 680R 0W125
live mains track on the top layer. 0W125 0805
RLY200A 0805
Takamisawa 0V(D)
Consider removing the holes for the F1CA005V 0V(D)
can or perhaps move mains tracks
onto bottom layer for next PCB C202 0V(D)
revision.
3N3
250V
CER
CON201
WAGO
3
256
BLUE
POWER AMP SUPPLIES
2
DK GREY
RLY200B 1
Takamisawa 1
ORANGE
GREEN
L916TX SP200
F1CA005V
CON202
WAGO
(CHASSIS-MOUNTED) +45V_R
C203
256 +45V_L
3N3
250V BLUE DBR200
CER 0V(SIG)
CON204 GBU8D C228 C229 0V(SIG)
1
BLUE 3,300UF 3,300UF R221 0R0
WHITE 2 0V(D)
LT GREY C205 63V 63V 0V(D)
BLUE 3
DK GREY 470N USR USR 0W125 0805
BLACK 4 0V_FB_R
GREY 100V 0V_FB_R
115V ac WAGO MKS2 0V_LS_L
256 0V_LS_L
BLACK GREY
0V_LS_R
0V_LS_R
ORANGE WHITE
3.2Vac
PCB Traces to route as shown here SP202
0V_HF_R
115V ac 0V_HF_R
WHITE
GREEN 0V_HF_L
0V_HF_L
ORANGE
16Vac
DBR201 C230 C231 0V(PSU)
BLUE
FIX200 GBU8D 3,300UF 3,300UF
Dia 3.2mm 16Vac 63V 63V 0V_FB_L
C206 USR USR 0V_FB_L
ORANGE
CON203 470N
1 1 GREEN/YELLOW
GREEN 100V
Interwinding Screen
WAGO MKS2 -45V_L
256 -45V_R
SP201
0W125
SOT-323
0805
-15V(A)
TO-220
HS202A
DRAWING TITLE 03_E264 MJT 09 Sept 03 Remove EMC can from around IEC inlet. 5.1
6043PB
23C/W A80/P80 Power Supplies 03_E230 MJT 04 Aug 03 None to this sheet. Display snapoff fixing holes reduced to 3.2mm 5.0
D211
BAS16
Filename: L943C2_5.1.SCH 03_E147 MJT 23 May 03 Removed double connection from R221 to star point. PCB change. 4.0
23425
SOT-323
Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 R204, R205 CHANGED FROM 2R2 TO 0R 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 2 of 8 DRAWING NO. L943C2
-> +45V_L
C408
R415 22UF
220R 63V
0W25 YK
MF ANNOTATION
0V_HF_L
R405 R406
D400 C404
47R 47R
BAS16 10N
0W125 0W125
SOT-323 100V
0805 0805
P401 0805
R400 P408
22K
0W125 0V_FB_L
TR401
0805 TR400
BC859B D405
BC859B
SOT-23 1N4003
SOT-23
PNP CURRENT MIRROR DO-41
P409
P404 TR402
FMMT597
SOT-23
R436
R417
C402 PRE DRIVER TR412A 10K
P405
ZDT6758 0W125
DZ400
1K0 SM-8 0805
100P 22V
0W125 BZX84C TR403
0805 100V FMMT597
0805 P407 SOT-23 P413
P410 R422 SOT-23
P411
NF R431 P414
R419 100R
NF 22R R442 R401
NF 0W125 P403
C400
R409
470K TR407
0805 0W125 4K7 10K VI PROTECT
P402 0W125 FMMT497 SIGNAL TO MICRO
0805 0W125 0W125
0805 SOT-23
1K0 0805 0805
47P 0W125 VIPROT_L
100V 0805
0V_FB_L OUTPUT STAGE V-I PROTECTION
0805
TR408
FMMT497
INTEGRATING DC SERVO TR412B P432
SOT-23 C422 ZDT6758 D402 C426
R420 SM-8 R438 10UF
C417 BAS16 R444 DZ406
C410 R423 10K 50V
DZ404 100N TR413 SOT-323 10K BZX84C
100UF 1M0 C423 220R 0W125 YK
BZX84C 50V 470N 0W125 3V9
25V 0W125 100UF 0W25 0805
15V 0805 100V P431 0805 SOT-23
YK 0805 100V MF R426 TR410
SOT-23 MKS2
BOOTSTRAP
YK FMMT497
0V_FB_L P430 100R SOT-23
6 D409
0W125
7 0V_HF_L
R456 0805
0V_HF_L 5 P420 R452
P427
R425 P429 TR409
R443 1K0 330R FMMT497
4K7 IC400B 1W R424 R432
Q403 0W125 100R SOT-23
0W125 TL072CD BAV99 CF 100R 22R
0805 0W125 D406
0805 SO-8 SOT-23 SAP15NY R411 0W125 0W125 0805 1N4003
SAP 1K0 0805 0805
DO-41
0W125
0V_FB_L 0V_FB_L 0805 CON401
RV400 HARWIN C412
D401 220R M20-973 100UF
R454 25V
BAS16 LIN 1
NF 100K YK
SOT-323 2
R451 18K 0W125
0805
0W25 MF NF
R458 18K
BIAS MEASURE BIAS
INPUT FILTER V TO I AMP IC400A ADJUST
TL072CD
R410 0W25 MF
8
3 SO-8
PRE_OUT_L R447 R449
1 OUT_L
DZ402 1K0 OUTPUT_L
2 R445
0W125 820R 820R
SHEET 3
BZX84C
22R
4
BOOTSTRAP
C419 0V_FB_L REF400 ZOBEL NETWORK
1W 0805 0W125
100N
R403 10K CF R414 0805 D407
50V C427
1K0 1N4003
0805 TR415 100N
0W125 0805 P440 0W125 DO-41
100V
Q409 0805 R430 P451 TR406
0V_HF_L LM431AIM3 MKS2
R439 C424 R457 FMMT597
22K SOT-23 100R SOT-23
100UF
0W125 330R P449 0W125
100V
0805 YK 0W125 0805 P452
0805 C421
R441
0V_HF_L
PRE DRIVER BIAS R428 10K D403 0V_LS_L
C406 & TEMP. COMP. 220R 0W125 BAS16
DZ405 R460 0W25 0805 SOT-323 100N
C414 10N SAP15PY 50V
100UF BZX84C 330R TR414A MF
100V ~1.6V SAP 0805
25V 15V 0W125 ZDT758
0805
YK SOT-23 TR404 0805 SM-8
P439 0V_LS_L
FMMT597 C415
SOT-23 100UF R413
25V 1K0 R433
C420
YK 0W125 22R
100N
0805 0W125 V-I PROTECTION
50V
0805
0805 NF TR405
NF R434
C401 FMMT597
R412 22R 0V_HF_L
0V_FB_L SOT-23 0W125 P406
P433 1K0 R427 0805
47P 0V_HF_L
0W125 P400 DZ401
100V 0805 P444 100R
0805 22V
P442 0W125 BZX84C
C403 0805 SOT-23
R418 P438 TR414B
NF
R421 ZDT758
1K0 SM-8
0W125 100P 470K PRE DRIVER
100V 0W125
0805 TR411 0805
0805 FMMT497
P456 SOT-23
0V_FB_L
P458
NPN CURRENT MIRROR D408
1N4003
TR417 DO-41
R404 TR416
BC849B
22K BC849B
SOT-23
0W125 SOT-23 0V_FB_L
0805 P454 P459
R407 R408
D404 C407
47R 47R
BAS16 10N
0W125 0W125
SOT-323 100V
0805 0805
0805
0V_HF_L
R416
220R C409
0W25 22UF
MF 63V
YK
-45V_L
DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
* - Default jumper setting on pins 2 & 3; fit jumper A80/P80 - Power Amp Left 03_E230 MJT 04 Aug 03 None to this sheet. Display snapoff fixing holes reduced to 3.2mm 5.0
on pins 1 & 2 to increase bias voltage; Filename: L943C4_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
remove jumper to decrease bias voltage 23425 Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
ITEM400 1 8K004 Con Jumper Socket 0.1IN Gold Blue Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 4 of 8 DRAWING NO. L943C4
-> +45V_R
C508
R515 22UF
220R 63V
0W25 YK
MF ANNOTATION
0V_HF_R
R505 R506
D500 C504
47R 47R
BAS16 10N
0W125 0W125
SOT-323 100V
0805 0805
P508 0805
R500 P501
22K
0W125 0V_FB_R
TR501
0805 TR500
BC859B D505
BC859B
SOT-23 1N4003
SOT-23
PNP CURRENT MIRROR P509 DO-41
P504 TR502
FMMT597
SOT-23
R536
R517
C502 PRE DRIVER TR512A 10K
P505
ZDT6758 0W125
DZ500
1K0 SM-8 0805
100P 22V
0W125 BZX84C TR503
0805 100V P513 FMMT597
0805 P507 SOT-23
R522 SOT-23
P511
NF P510 100R R531 P514
NF R519 Q500
NF 0W125 22R R542 R501
C500
R509
470K TR507
0805 0W125 4K7 10K VI PROTECT
P502 0W125 FMMT497 SIGNAL TO MICRO
0805 0W125 0W125
0805 SOT-23
1K0 0805 0805
47P 0W125 VIPROT_R
100V 0805
0V_FB_R OUTPUT STAGE V-I PROTECTION
0805
TR508
FMMT497
INTEGRATING DC SERVO TR512B P532
SOT-23 C522 ZDT6758 D502 C526
R520 SM-8 R538 10UF
C517 BAS16 R544 DZ506
C510 R523 10K 50V
DZ504 100N TR513 SOT-323 10K BZX84C
100UF 1M0 C523 220R 0W125 YK
BZX84C 50V 470N 0W125 3V9
25V 0W125 100UF 0W25 0805
15V 0805 100V 0805 SOT-23
YK 0805 100V MF R526 P531 TR510
SOT-23 MKS2
YK FMMT497
0V_FB_R
BOOTSTRAP
100R SOT-23
6 D509 P530 0W125
7 0V_HF_R
R556 0805
0V_HF_R 5 P520 R552
P527
R525 P529 TR509
R543 1K0 330R FMMT497
4K7 IC500B 1W R524 R532
Q503 0W125 100R SOT-23
0W125 TL072CD BAV99 CF 100R 22R
0805 0W125 D506
0805 SO-8 SOT-23 SAP15NY R511 0W125 0W125 0805 1N4003
SAP 1K0 0805 0805
DO-41
0W125
0V_FB_R 0V_FB_R 0805 CON501
RV500 HARWIN C512
D501 220R M20-973 100UF
R554 25V
BAS16 LIN 1
NF 100K YK
SOT-323 2
R551 18K 0W125
0805
0W25 MF NF
R558 18K
BIAS MEASURE BIAS
INPUT FILTER V TO I AMP IC500A ADJUST
TL072CD
R510 0W25 MF
8
3 SO-8
PRE_OUT_R R547 R549
1 OUT_R
DZ502 1K0 OUTPUT_R
2 R545
0W125 820R 820R
SHEET 3
BZX84C
22R
4
BOOTSTRAP
1W 0805 0W125
100N
R503 10K CF R514 0805 D507
50V C527
1K0 1N4003
0805 TR515 100N
0W125 0805 P540 0W125 DO-41
100V
Q509 0805 R530 P551 TR506 MKS2
0V_HF_R R539 LM431AIM3
C524 R557 FMMT597
22K SOT-23 100R SOT-23
100UF
0W125 100V 330R P549 0W125
0805 YK 0W125 0805
0805 P552
C521
R541
0V_HF_R
PRE DRIVER BIAS R528 10K D503 0V_LS_R
C506 & TEMP. COMP. 220R 0W125 BAS16
DZ505 R560 0W25 0805 SOT-323 100N
C514 10N SAP15PY 50V
100UF BZX84C 330R TR514A MF
100V ~1.6V SAP 0805
25V 15V 0W125 ZDT758
0805
YK SOT-23 TR504 P539 0805 SM-8
0V_LS_R
FMMT597 C515
SOT-23 100UF R513
25V 1K0 R533
C520
YK 0W125 22R
100N
0805 0W125 V-I PROTECTION
50V
0805
0805 NF TR505
NF R534
C501 FMMT597
R512 22R 0V_HF_R
0V_FB_R SOT-23 0W125 Q511
P533 1K0 R527 0805
47P 0V_HF_R
0W125 P546 DZ501
100V 0805 P544 100R
0805 22V
P542 0W125 BZX84C
C503 0805 SOT-23
R518 P538 TR514B
NF
R521 ZDT758
1K0 SM-8
0W125 100P 470K PRE DRIVER
100V 0W125
0805 TR511 0805
0805 FMMT497
P556 SOT-23
0V_FB_R
DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
* - Default jumper setting on pins 2 & 3; fit jumper A80/P80 - Power Amp Right 03_E230 MJT 04 Aug 03 None to this sheet. Display snapoff fixing holes reduced to 3.2mm 5.0
on pins 1 & 2 to increase bias voltage; Filename: L943C5_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
remove jumper to decrease bias voltage 23425 Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
ITEM500 1 8K004 Con Jumper Socket 0.1IN Gold Blue Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 5 of 8 DRAWING NO. L943C5
ANNOTATION
A80 ITEMS COMMON ITEMS P80 ITEMS
+4.8V(D)_DISP (Fitted on A80 only) (Fitted on both A80 & P80) (Fitted on P80 only)
TO MAIN PCB - SHEET6
R802 R803
C802
100N
10K
0W125
10K
0W125 CON800 MOLEX 52044 NOTE:
50V
MOUNTED 0805
0805 0805 R825
REMOTE_DISP All resistor / small capacitor
Q802
UNDER IR EYE
combinations are placed near
10
11
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
8
9
330R C825
0V(D)_DISP
P803 TR801 0W125 1N0
RX800
Q803
Q804
Q805
Q806
Q807
Q808
Q809
Q810
Q811
Q812
Q813
Q814
Q815
Q816
Q817
Q818
Q819
LED806 BC849B 0805 100V flexfoil connector for EMC filtering
+5V
SM SOT-23 0805 +4.8V(D)_DISP
R800 P802 TR800
O/P BC849B
CHAS_DISP
10K SOT-23
GND
RED 0V(D)_DISP
0W125 R801
SML-010
0805 10K
PIC-26043TM2 0W125
P801
0805
R810
-38V_VFD
0V(D)_DISP
R856 330R 0R0
0W125 R811 R812 R813 R850 R814 R815 R816
DZ800 0V(D)_DISP
0W125 0805 0805 0R0 0R0 0R0 0R0 0R0 0R0 0R0
BZX84C
0W125 0W125 0W125 0W125 0W125 0W125 0W125
22V FIX800
R855 P805 0805 0805 0805 0805 0805 0805 0805
SOT-23 Dia 3.2mm
VFD LOCATORS Q876 CHAS_DISP
1K0 R853 R854 (used to
DZ801 C830 C831 C826 C827 C828 1 0V(D)_DISP
R807 0R0 BZX84C 0805 CATHODE BIAS 100R 100R
C804 10N 10N 1N0 1N0 1N0 tie down
0W125 0W125 0W125 Q820 track at
5V6 100N 100V 100V 100V 100V 100V
0805 0805
330R
330R
330R
0W125 0805 display side)
0805
0805
0805
SOT-23 50V 0805 0805 0805 0805 0805 C806
R808 0R0 C800 C803 0805 100N
C812 C813
10UF 100N CHAS_DISP 50V
0W125 0805 R851 R852 10UF 10UF
Q877 50V 50V C835 C836 0V(D)_DISP 0805
10K 10K 50V 50V
C801 SM 0805 10UF 10UF
0W125 0W125 SM SM
50V 50V C837 C838 0V(D)_DISP
0W125
0W125
0W125
0805 0805 Q873
R827
R828
R829
10UF SM SM 47P 47P
0V(D)_DISP 50V 0V(D)_DISP P804 100V 100V FIX808
SM TR806 FMMT597 -25V(FL)_A80 0805 0805 Dia 3.2mm
SOT-23 CHAS_DISP
CHAS_DISP 1
*PWR_LED_GRN_DISP
*PWR_LED_RED_DISP
100N +4.8V(D)_DISP
0R0 C805 C832 C833 C811 50V
0W125 100N 100UF 100UF 100N 0805
+4.8V(D) / 0V(D)
VFD_CS / 0V(D)
0805 6.3V 6.3V
*RESET_DISP
50V 50V
PCOM
SM SM
FIL1 / 0V(D)
FIL2 / 0V(D)
0805 0805
PAp
PDp
G10
0V(D)_DISP
Pm
G9
G8
G7
G6
G5
G4
G3
G2
G1
Pn
Pg
Pk
Pb
Ph
Pd
Pe
Pa
Pc
Pf
Pj
Pl
Pi
TR804 TR805
F
Q853
0V(D)_DISP 0V(D)_DISP FIX807 MMUN2111LT1 MMUN2111LT1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
32
1
4
5
6
7
8
9
Q828
Q829
Q831
Q832
Q833
Q834
Q835
Q836
Q837
Q838
Q839
Q840
Q841
Q842
Q843
Q844
Q845
Q846
Q847
S7
S6
S5
S4
S3
VCC
P22/D14/S13
P23/D15/S12
P11/S9
P10/S8
GND
50V C815
0805 0W125 100N
1 33
P21/D13/S14 S2 0805 50V
2 32 -25V(FL)_A80 LM809M3-3.08
P20/D12/S15 S1 0805
3 31 SOT-23
2
P03/D11 S0
4 30
P02/D10 P34/K4
5 29 0V(D)_DISP CHAS_DISP
P01/D9 P33/K3
6 28
P00/D8 P32/K2
7 27
D7 P31/K1
8 26
D6 P30/K0 R818
9 25 Q858 VFD_SDO / *SP1_SW DISP
Q862
Q863
Q864
D5 SDO
10 24 Q859
D4 SDI 0R0
11 23 Q860
NC SCK 0W125
R840 R841 0805
47K 47K R820
0W125 0W125 PHASE_B / *SP2_SW DISP
D800
OSC1
OSC2
NCS
VPP
VSS
BAS16
NC
0R0
D3
D2
D1
D0
SOT-323 0W125
0W125 0805
-25V(FL)_A80 PT6351
12
13
14
15
16
17
18
19
20
21
22
0805 R819
LQFP-44 VFD_SCLK / *PWR_BTN DISP
Q861 0R0
TUNER
0W125
SW801 0805
0V(D)_DISP R821
0R0
-25V(FL)_A80 0W125
1
0805
+4.8V(D)_DISP X800
P800 4.00MHz
D802 CHAS_DISP
C816 C817 3 1
BAS16 ENTER SELECT PHONO CD FIX801 FIX802 FIX803 FIX804 FIX805 FIX806 R822 R823 R824
100N 100N Dia 3.2mm Dia 3.2mm Dia 3.2mm Dia 3.2mm Dia 3.2mm Dia 3.2mm
SOT-323 SW804 SW806 SW808 SW810 0R0 0R0 0R0
50V 50V
0W125 0W125 0W125
0805 0805 1 1 1 1 1 1 0805 0805 0805
0V(D)_DISP SIL-3 2 Q885 Q886 Q887 Q888 Q889 Q890
1
LED805 LED804 LED803 DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
5mm 5mm 5mm A80 & P80 Display Circuitry 03_E230 MJT 04 Aug 03 Display snapoff fixing holes reduced to 3.2mm 5.0
GRN GRN GRN
LED 5mm LED 5mm LED 5mm
ARCAM
Filename: L943C8_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
0V(D)_DISP 0V(D)_DISP 0V(D)_DISP
Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
SP1_LED SP2_LED PROCESSOR_LED
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
Cambridge CB5 9QR Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 8 of 8 A2 DRAWING NO. L943C8
ITEM700 3 8K004 Con Jumper Socket 0.1IN Gold Blue NF ON A80
ANNOTATION
+45V_L
R724 R725
22K 22K
TRIGGER OUT TR700
0W125
0805
0W125
0805
BD179
TO-126
R715 P707 TR701
P708 BC849B
R726 100R SOT-23
22R 0W125 Q709
SKT700 0W125 0805
HOSIDEN HSJ ~13.5V @ 30mA max 0805
NC1
C720
10UF
50V
R727 YK
NC2 10K
DZ700
0W125
BZX84C
0805
C700 15V
100N SOT-23
GND2
GND1
50V
0805
P80 TRIGGER IN
C710 (NF ON A80)
REMOTE_P
TO SHEET 6
100P
100V
0805
REMOTE_N
D704
<-------- Vin
NF ON P80 R706 +4.8V(D)
C705 C701
0R0 R738
100N 100N
0W125 2K2
50V 50V
0805 0W125
0805 0805 SOT-23 BAT54S
0805 R707
Vout=0.82Vin Q715 1 2
TRIG_IN
0V_CHASS
4K7
L700 R728 0W125
DZ701
70R@100MHz 10K 0805
BZX84C
0W125
4V7
0805
+45V_L SOT-23
+45V_L
+4.8V(D) 0V(D)
+4.8V(D)
0V(D)
0V(D)
0V_CHASS
0V_CHASS
0.38Hz_CLK
0.38Hz_CLK
*RESET
+4.8V(D) +4.8V(D)_2
R700 P701
C702
P700
0W125
0805 SO-14
0805 YK 0805
P80 DELAYED OFF IC701B +4.8V(D)_2
4
4
100V 0V(D) IC703A
0805 0805 100K R708
0805 CON700 2 5 IC703C +4.8V(D)_2
SD
R709 0W125 100K D Q
33K 2 0W125 14
0805 VCC
0W125 1 R711 0805 3 C709
CLK
0805 D700 22K IC701A 100N
HARWIN C716 9 6
RD
NF 100UF 0W125 Q0 Q718 Q 50V
M20-973 0805 7 0805
P716 R714 P715 25V Q1 Q719
+4.8V(D)_2 6 74HCT74D 7
1
0V_PREOUT YK Q2 GND
5 SO-14
0R0 SET SENSITIVITY Q3
R721 BAV99 SOT-23 R736 3 74HCT74D 0V(D)
0W125 Q4 AUTO-OFF
0R0 R710 Jumper Fitted = ~0.5mVrms (default); 0V(D) +1.6V(D) IC700B 3K3 2 0V(D) SO-14
0805 Q5 Q724
0W125 33K Jumper Not Fitted = ~2mVrms D701 LM324D 0W125 IC700D 4 DELAY SET LATCH
Q6
0805 0W125 SO-14 0805 LM324D 13
10
C706 Q7
0805 5 SO-14 12 IC703B
Q8
C712 7 P711 12 Q713 10 14 CON702 12 9 +4.8V(D)_2
SD
100P P712 CP Q9 D Q
0V(D) 6 P706 14 Q714 LATCH & COUNTER RESET 11 15 1 0V(D)
100V P714 MR Q10
BAV99 SOT-23 100N 13 1 2 11
0805 Q11 CLK
+1.6V(D) 50V 3 TR702
0805 74HCT4040D 8 P724 MMUN2111LT1
RD
R712 R713 R737 Q
R703 22K 2K2 SO-16 HARWIN SOT-23
IC700C M20-973 74HCT74D
13
100K 0W125 100K 0W125 Q727
0W125 LM324D 0805 0805 SO-14
C703 0W125
0805 SO-14 R733
R701 P709 0805
10 Pins 1&2: ~12 mins (default) 3K3
PRE_OUT_R P713
P704 8 Pins 2&3: ~45 mins 0W125
100K P705
100N 9 0805
0W125
50V 0V(D) Power-On Reset
0805
0805
0V(D)
R717 R723
330R 680R R705
0W125 0W125
0805 0805 100K
CON701
0W125
2
0805
1
D702
HARWIN C717
M20-973 100UF
25V
YK
SET SENSITIVITY BAV99 SOT-23
Jumper Fitted = ~0.5mVrms (default); 0V(D)
Jumper Not Fitted = ~2mVrms D703
DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
A80/P80 Trig, RC5 & P80 Sig Det 03_E230 MJT 04 Aug 03 None to this sheet. Display snapoff fixing holes reduced to 3.2mm 5.0
Filename: L943C7_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
23425
BAV99 SOT-23
Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 7 of 8 DRAWING NO. L943C7
ITEM600 1 8K004 Con Jumper Socket 0.1IN Gold Blue Fit on CON601 after programming; NF ON P80
VOL_SDATA_u
*PRE_MUTE_u
+4.8V_D_PRE
SO-8
VOL_SCLK_u
0W125 0805
LISTEN_2_u
LISTEN_1_u
LISTEN_0_u
VOL_*CS_u
Q600 *PRE_MUTE_u +45V_L
THERMAL CUTOUT
TAPE_2_u
TAPE_1_u
TAPE_0_u
*PRE_MUTE
+4.8V(D)
Q601 +4.8V_D_PRE
+4.8V_D_PRE
RTH600 0V(D)
PTC 110DEG
0V_D_PRE DZ600 PTC
P601 R611 10K
Q603 TAPE_0_u BZX84C VFD_CS +4.8V(D) IC604B
TAPE_0 P617 SP602
TO SHEET 3
3V9 *PWR_LED_RED 8
P602 0W125 0805 R612 10K R638 VCC
Q604 TAPE_1_u Connect near SOT-23 *PWR_LED_GRN
TAPE_1 680R C608
IC602 0W125 100N
P603 R613 10K 0W125 0805
Q605 TAPE_2_u VFD_SCLK / *PWR_BTN
TAPE_2 0805 50V
VFD_SDO / *SP1_SW 0805
P604 0W125 0805 R614 1K0
Q606 VOL_SCLK_u P618 VFD_SDATA / *SP1_LED 4
VOL_SCLK GND
P605 R626 10R 0W125 0805
Q607
Q614 TR602
CON601 0V(D) 24C02
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
0V_SER FMMT597
IC600B HARWIN IC602 SO-8
P606 0W125 0805 R615 1K0
Q608 VOL_SDATA_u 0V(D)
SOT-23
IC601D 4 M20-973 Fit jumper for
P55/WKP5/ADTRG
P12
P11
P75/TMCIV
P74/TMRIV
P56/SDA
P76/TMOV
NC
NC
NC
NC
P57/SCL
P10/TMOW
P54/WKP4
P53/WKP3
P52/WKP2
VOL_SDATA R640 P619 R620 Q640
33K 9 8 6 normal operation
P607 R616 10K 0W125 0805
Q609 LISTEN_0_u 5
LISTEN_0 0W125 2K2 P628
0805 R645 R646 0W125 74HC14 33 16 C610
2
1
P608 0W125 0805 R617 10K
Q610 LISTEN_1_u DZ603 C603 SO-14 74HC00D 34
NC NC
15
LISTEN_1 4K7 4K7 0805 SO-14 NC NC 100N
BZX84C 100N *NMI 35 14
P609 R618 10K 0W125 0805 0W125 0W125 NMI P51/WKP1 50V
Q611 LISTEN_2_u 4V7 50V 36 13
LISTEN_2 0805 0805 R637 P80/FTCI P50/WKP0 0805
SOT-23 0805 37 12
0W125 0805 100K P81/FTIOA Vcc
0W125 38 11
P82/FTIOB OSC1
+4.8V(D) 0V(D) 0805 39 10
P83/FTIOC OSC2
+45V_L +45V_R +4.8V(D) 40 9
R631 P633 P84/FTIOD Vss
R629 P600 41 8 C609
+45V_L P85 TEST
47R 42 7 0V(D) 100N
10K P86 RES
+45V_R 0W125 RTH601 IC600C 43 6 50V
0W125 P87 Vcl
IC601G 0805 PTC 110DEG 9 DC_OFFSET 44 5 0805
+45V_R 0805 P20/SCK3 X1
14 P613 DZ601 PTC 8 Q638 THERM *PWR_LED_RED RS232_RX 45 4 P631
VCC BZX84C P21/RXD X2
+4.8V(D) 10 *PWR_LED_GRN RS232_TX 46 3
P17/IRO3/TRGV
C602 C619 C620 3V9 P620 P22/TXD AVcc
R639 47 2 P632
+4.8V(D) 100N 100UF 100UF SOT-23 74HC00D NC NC
2
1
680R 48 1
25V 25V SO-14 NC NC
P14/IRQ0
P15/IRQ1
P16/IRQ2
50V
PB4/AN4
PB5/AN5
PB6/AN6
PB7/AN7
PB3/AN3
PB2/AN2
PB1/AN1
PB0/AN0
0W125 Fit jumper to
7 0805 YK YK re-program
0V(D) GND 0805 P630
CON602
NC
NC
NC
NC
0V(D) 74HC14 0V(D) P621 HARWIN
SO-14 M20-973 HD64F3664FP
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Q616 TR603
L943SW
FMMT597
IC600D LQFP-64
SOT-23
R641 IC601E 12
REMOTE_P P622 R621 Q641
33K 11 10 11
(From Sheet 7)
0W125 P629 13
REMOTE_N 2K2
0805 R647 R648 0W125 74HC14 0V(D)
DZ604 C604 SO-14 74HC00D
4K7 4K7 0805 SO-14
BZX84C 100N
0W125 0W125
4V7 50V
AC PRESENT DETECT 0805 0805
SOT-23 0805 REMOTE
3
PHASE_A / *SP2_LED
+4.8V(D) 0V(D) PHASE_B / *SP2_SW X600
*RESET
SPKR2_ON
SPKR1_ON
2
4.00MHz
R630 AC_PRESENT SIL-3
3K3 DC_OFFSET 0V(D)
0W125 NF ON P80 VI_LIM
C625
1
0805 1N0 THERM
C606 SPKR2_ON 4 25
P80:*SP2_LED
P80:*SP1_LED
0W125
P80:*SP2_SW
P80:*SP1_SW
PA2 PA5
P80:0V(D)
P80:0V(D)
P80:0V(D)
P80:0V(D)
AC_PRESENT 10 19
PB0 RES C611
11 18
IC601B VSS PC5
A80:VFD_SDATA
12 17 100N
A80:VFD_SCLK
P611
A80:PHASE_A
A80:PHASE_B
3 4 1 THERM 13 16 50V
A80:REMOTE
A80:+4.8V(D)
A80:VFD_CS
Q620
Q621
Q622
Q623
Q624
Q625
Q626
Q627
Q630
Q643
Q644
Q645
NF NF
C614 C615 +4.8V(D)
FIX600
IC601C Dia 3.5mm
NF ON P80
R628 P612 C618 C632 C633
5 6 10N 10N 0V(D) -38V_VFD C605
22
21
20
19
18
17
16
15
14
13
12
11
10
VIPROT_R 10N 47P 47P DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
9
8
7
6
5
4
3
2
1
1
4K7
0W125
C613
74HC14
P616 100V
0805
100V
0805
100V
100N
50V
100V 100V Q639 A80/P80 Protection & Micros 03_E230 MJT 04 Aug 03
Changed P80 s/w & fitted IC socket for IC603 (P80 only).
5.0
10N 0805 0805 0805 C607 Display snapoff fixing holes reduced to 3.2mm
0805 SO-14 0805
100V CON600 MOLEX 52045 100N
Filename: L943C6_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
23425
0805 0V(D) 0V(D) 50V
0805
Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
0V(D)
TO DISPLAY - SHEET 8 0V(D)
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 6 of 8 DRAWING NO. L943C6
ITEM300 6 8K004 Con Jumper Socket 0.1IN Gold Blue 4 of these NF on P80
TAPE INPUT TAPE OUTPUT ITEM301 2 E802AP Pad Damping 15x6x3MM Sorbothane 1/2 pad placed on top of C386, C387, C388 & C389 (NF on P80)
C334
+15V(A) 1N0
100V FIT ON P80 ANNOTATION
D302 0805
R318
A80 Line Out / A80 PreAmp Out /
SCRN
C322
470P
100K
0W125 0V(SIG) TAPE OUTPUT SELECT TAPE OUTPUT P80 Pre Out Loop P80 PowerAmp In
-15V(A) 100V 0805 SKT300 IC304B R338
BAV99 SOT-23 +15V(A) P343 5 C335
FKP2 P349 R332 47R 10R 0V_PREOUT
+15V(A) 7 TOP_L 1N0
R303 0W125 (Sheet 7)
TOP_R 6 100V
0805
13
13
D300 0W125 0805 0805
KUNMING IC300 IC301 R330 SP300 D305
1K0 TL072CD
GOLD PHONO L 4 PHONO R 4 D303 +15V(A)
V+
V+
0W125 X0 X0 1M0 SO-8
SCRN
5 5 0W125 +15V(A)
R302 0805 X1 X1
TOP_L AUX L 6 8 AUX R 6 8 0805 0V(SIG)
REAR PANEL VIEW X2 D X2 D
R317 C320 CD L 7 CD R 7 -15V(A)
1K0 X3 X3
+15V(A) 100K 470P TUNER L 12 TUNER R 12 -15V(A) BAV99
0W125 X4 X4 C340
0W125 100V AV L 11 AV R 11 0V(SIG) +15V(A) BAV99 SOT-23
TAPE IN R
0805 X5 X5
TAPE IN L
BAV99 C302 C303 +15V(A) DVD L 10 DVD R 10 IC304A SOT-23
0805 FKP2 X6 X6
C300 SOT-23 AUX2 L 9 AUX2 R 9 TL072CD KUNMING
10N X7 X7
-15V(A) +5V(A) +5V(A) SO-8 100N GOLD
100V 0V(SIG) -15V(A) 10N 10N 2 2 50V 0V(SIG)
0805 EN EN P344
8
100V 0V(SIG) 100V TAPE_0_PRE 1 TAPE_0_PRE 1 3 0805
A0 A0 P350 R333 47R REAR PANEL VIEW
0805 0805 TAPE_1_PRE 16 TAPE_1_PRE 16 1 TOP_R
C301 A1 A1
0V(SIG) TAPE_2_PRE 15 TAPE_2_PRE 15 2 SKT301
10N A2 A2 C341 0W125 0805
+15V(A) R331 D306
4
100V R300
DVD R 14 14 1M0 D304 +15V(A)
0805 D301 GND GND
1
2
R316 C321 0W125 +15V(A)
1K0 CON301
V-
V-
0W125 100K 470P 0805 100N HARWIN
-15V(A) 0W125 100V 0V(SIG) DG408DY 0V(SIG) DG408DY -15V(A) 50V -15V(A)
3
0805 M20-973
0805 FKP2 SO-16 SO-16 0805 -15V(A) BAV99
0V(SIG) BAV99 SOT-23
1
2
-15V(A) SOT-23
CON300
0V(SIG)
R301 HARWIN
BAV99
SOT-23
DVD L
M20-973 FIT JUMPERS
-15V(A) BAV99 SOT-23
1K0
0805
R319
100K
C323
470P
ONLY ON P80
DVD INPUT +15V(A)
SKT302
0W125 0W125
0805
100V
FKP2
PHONO PREAMP LINE OUTPUT
PHONO L IC305B
REAR PANEL VIEW
-15V(A) 0V(SIG) 5
C336 D309 0V(SIG) +15V(A) C343 7 P351 R334 47R +4.8V_D_PRE
R379 P304 6
SCRN KUNMING IC306A
C306 C308 0W125 0805 D320 RLY300C
1
2
3
GOLD +15V(A) NJM2114M R381
10K TL072CD C376 BAS16
D310 DMP-8 D311
0V(SIG) 1N0 100N 0W125 SO-8 22P
10K
SOT-323
NEC
100V +15V(A) 50V 0V(SIG) 0W125 +15V(A) EB2-5NU
C373 0805 100V
8
0805 -15V(A) 10N 10N PHO L 3 0805 0805
100V 0V(SIG) 100V 1 0805 CON304
C355 Q320 *PRE_RLY
-15V(A) 0805 0805 2 R375 R346 -15V(A) HARWIN
0V(SIG) BAV99 SOT-23 47P C342 100N 10UF BAV99 M20-973
2K2 820R
4
R306 100V
+15V(A) AV L 0W125 50V 0W125 SOT-23
R385
AV INPUT R322 C326
0805
0805 YK 0805 TR300P363
D307 1K0 *PRE_MUTE
50V 0805 BC849B
0W125
0805
100K
0W125
470P
100V -15V(A)
C365 0V(SIG)
FIT JUMPERS ON SOT-23
3K3
0W125
C353 R339 +15V(A) C344
R305 0805 FKP2
47K R349 R307 P300 R351 P301 R373 220UF PINS 1 & 2 (2 & 3 0805
0W125 16V IC305A
*PRE_MUTE_PRE
1K0
0W125
R320
100K
C324
470P 0V(SIG) 100P 0805
R345
820R
680K
0W125
1K0
0W125
22K
0W125
33K
0W125
YK TL072CD
SO-8 100N FOR PRE/PWR) 0V_D_PRE
100V 50V 0V(SIG)
0805 0W125 100V 0W125 0805 0805 0805 0805
FKP2
8
+15V(A) BAV99 0805 FKP2 AV R 0805 0V(SIG) 3 0805
R376 P352 R335 47R
SOT-23 C361 1 +15V(A)
2K2 R380 P305
-15V(A) 1N0 2
C304 C357 C359 C363 0W125 C345 0W125 0805
1
2
3
0V(SIG) 100V R382 FIT ON P80
4
10N C307 C309 22UF 0805 10K C377 C310
+15V(A) FKP2 10K D312
100V 50V 0W125 22P 10N
0W125 +15V(A)
0805 CFNE 0805 100V 100V
4N7 330P -15V(A) 100N 0805 TAPE_0_PRE
0805 0805 TAPE_0
-15V(A) 10N 10N 100V 100V -15V(A) 50V TAPE_1_PRE
FROM SHEET 6
CON305 TAPE_1
0V(SIG) C305 100V 0V(SIG) 100V 0V(SIG) FKP2 FKP2 0805 -15V(A) HARWIN TAPE_2_PRE
10N FIT ON P80 TAPE_2
0805 0805 BAV99 M20-973 0V(SIG) C311
100V +15V(A) PHONO R SOT-23
R304 10N
0805 TUNER R VOL_*CS_PRE
100V VOL_*CS
D308 VOL_SDATA_PRE
1K0 R321 C325 0805 VOL_SDATA
-15V(A) PHO R 5 C374 0V_SER_PRE
0W125 100K 470P 0V_SER
0W125 100V 7 -15V(A) VOL_SCLK_PRE
0805 C356 VOL_SCLK
0805 FKP2 6 R377 R347
47P IC306B 10UF +15V(A)
2K2 820R
100V NJM2114M LISTEN_0_PRE
0W125 50V 0W125 LISTEN_0
0V(SIG) 0805 DMP-8 YK FIT ON P80 LISTEN_1_PRE
R310 0805 0805 LISTEN_1
BAV99 TUNER L C354 R340 C318 LISTEN_2_PRE
47K R350 R313 P302 R360 P303 R374 10N LISTEN_2
SOT-23 1K0 R324 C328
-15V(A) BAV99 SOT-23 0W125 C366 0V(SIG) 100V
0805 100K 470P R348 680K 1K0 22K 33K 220UF
TUNER INPUT +15V(A)
0W125 0W125 100V
100P 0805
820R 0W125 0W125 0W125 0W125
0805 +15V(A)
+15V(A)
SKT303 100V 16V +5V(A)
0805 FKP2 0W125 0805 0805 0805 0805 YK FIT ON P80 +5V(A)
FKP2 0V(SIG) 0V(SIG)
REAR PANEL VIEW
12
0W125 0W125 0805 R357 22K P328
4
0W125 100V CD L IC302 100V IC307A IC309 HARWIN
0805
+15V(A) BAV99 CD R 4 0805 NJM2114M PGA2310UA M20-973
VA+
VD+
V+
0805 FKP2
2
1
R354 22K 0W125 0805 X0 C387
SOT-23 TUNER L P329 5 DMP-8 100N SO-16W 5
X1 Q328 C386 R336
8
-15V(A) 6 8 2 50V 0V(SIG) 7
C312 0W125 0805 R358 22K X2 D R387 P358 PRE_OUT_L
0V(SIG) AV L 7 1 0805 VINL 16 6
10N C315 C316 X3 VINL 47R
+15V(A) 12 3 R383 14 R388 100UF
100V R355 22K 0W125 0805 X4 C346 VOUTL 3K3 C379 0W125
P354
DVD L P330 11 100UF 10K 3K3 IC307B 25V
0805 X5 4 0W125 22P 0805 NF
P331 10 0V(SIG) 25V 0W125 0W125 NJM2114M CFNE R399
R312 P319 0W125 0805 R359 22K X6 0805 100V
-15V(A) 10N 10N AUX2 L 9 CFNE 0805 0805 DMP-8 R362 22K
C313 X7 0805
0V(SIG) 100V 0V(SIG) 100V +5V(A) -15V(A) 100N 15 VOUTL
10N 1K0 R326 C330 0W125 0805 P332 AGNDL 22K 0W125
0805 0805 100K 470P 2 R341 50V 0V(SIG) R386 0W125 0805
100V 0W125 EN C367 C368
0W125 100V LISTEN_0_PRE 1 47K 0805 3K3 0V(SIG) 10 0805
0805 R308 0805 A0 220UF 220UF AGNDR
+15V(A) AUX R 0805 FKP2 LISTEN_1_PRE 16 0W125 0W125
A1 16V 16V
R327 C331 LISTEN_2_PRE 15 0805 0805 R393
D317 1K0 A2 YK YK C381
-15V(A) 100K 470P 0V(SIG) VOUTR 3K3 IC308B 0V(SIG) CON303
0W125 22P
0W125 100V 0V(SIG) 14 R342 R389 0W125 NJM2114M HARWIN
0805 GND 100V
0805 FKP2 100K 3K3 VINR 9 11 0805 DMP-8 M20-973
2
1
VINR VOUTR R392
V-
P355
0805 6 C389
0W125 0W125 R337
0V(SIG) DG408DY 0805 0805 P360 7
3
3K3 PRE_OUT_R
DGND
SO-16
MUTE
0V(SIG) 0V(SIG_2) 5
ZCEN
SCLK
R314 0W125 47R
SDO
VA-
AUX L
SDI
100UF
CS
0805 0W125
BAV99 R328 C332 -15V(A) -15V(A) 0V(SIG) 0V(SIG) 25V
1K0 R363 22K P334 R371 22K 0805
SOT-23 BAV99 SOT-23 PHONO R -15V(A) CFNE
13
100K 470P
1
8
2
6
3
5
0805
-15V(A) +15V(A) 0W125 100V R372
0W125 0W125 0805 R367 22K P335 0W125 0805 C385
AUX INPUT SKT304 0805 FKP2 TAPE IN R C380 C352 0V(SIG) 22K
+15V(A) 10UF 100N *PRE_MUTE_PRE RLY300A RLY300B
REAR PANEL VIEW
X5 0R0
BAV99 SOT-23 PHO L P340 10 0V(SIG) 25V 0W125 0V(SIG) 1N0 0V(SIG)
R315 P320 0W125 0805 R370 22K X6 0W125
PHONO/ 0V(SIG) AUX2 R 9
X7 CFNE 0805 100V 0805
-15V(A)
+5V(A) -15V(A) 100N 0805
AUX2 INPUT CON307 1K0 R329 C333 0W125 0805 P341
+15V(A) 100K 470P 2 R343 50V 0V(SIG) R390
HARWIN 0W125 EN C370 C371
0W125 100V LISTEN_0_PRE 1 47K 0805 3K3 0V(SIG)
0805 A0 220UF 220UF DRAWING TITLE 03_E264 MJT 09 Sept 03 None to this sheet. Remove EMC can from around IEC inlet. 5.1
INPUT BUS
GND Filename: L943C3_5.1.SCH 03_E147 MJT 23 May 03 None to this sheet. PCB change. 4.0
PLACE JUMPERS ON PINS 1 & 2 100K 3K3
23425
V-
AUX2 R 0W125 0W125 Notes: 03_E120 TGP 13 May 03 LEDs, BIAS & DOCUMENTATION CHANGE 3.0
TO ENABLE PHONO (DEFAULT), PHO R 0V(SIG) DG408DY
3
0805 0805
BAV99 SO-16
A & R Cambridge Ltd. A80 03_E116 TGP 17 APR 03 NO CHANGE TO THIS SHEET 2.1
SOT-23
-15V(A)
PINS 2 & 3 FOR AUX2 -15V(A) -15V(A)
Pembroke Avenue
ECO No. INITIALS DATE DESCRIPTION OF CHANGE ISSUE
Waterbeach
-15V(A)
Cambridge CB5 9PB Contact Engineer: Mark Tweedale Contact Tel: (01223) 203 200 Printed: 9-Sep-2003 Sheet 3 of 8 DRAWING NO. L943C3
Transformer Specification for 115/230V 50/60Hz mains transformer (for audio).
Arcam Part Number L916TX.
3. Transformer to have dual 115V primaries to allow parallel operation for 115V
input and series operation with 230V input. 3.2Vac WINDING
4. Transformer input voltage range as follows:
PRIMARIES
115V -15% +15% (97.5V to 132.5V)
230V -15% +15% (195V to 265V)
ORANGE
Mechanical Specification
--------------------------------------------------- WHITE
3.2Vac @ 55mA*
12. Primary wires self-ended and individually sleeved, then sleeved together. WHITE
Secondary wires self-ended and individually sleeved. Low power secondary
centre tap to share common sleeve. Use PVC sleeving.
GREEN/YELLOW
13. Primary/Secondary leadout separation to be minimised. Interwinding Screen
14. Product is for hi-fi audio; hum must be minimised. * - wire diameter at least 0.4mm
15. All wire lengths are +20, -0 mm. All wires stripped 8 +/-2mm and tinned.
+Vout +Vout
BLACK + WHITE GBU8D 8A 200V
Input Voltage (series primaries) 230V 265V
+
6800uF
On-Load Current 6.0A 6.0A
63V
BLUE Min On-Load Trough Voltage 41 +1.5/-0 V - Peak Voltage
Load
Off-Load Current - 100mA Trough Voltage
+
6800uF
63V
Max Off-Load Peak Voltage - 63V
0V (Black + White)
-Vout
DRAWING TITLE
DiVA A80 Power Transformer
Filename: L916TX_1.0.Sch
Notes:
3. Transformer to have dual 100V primaries to allow parallel operation with 100V
input. 3.2Vac WINDING
4. Transformer input voltage range as follows:
PRIMARIES
100V -15% +15% (85V to 115V)
9. Max core flux density 1.5T at nominal rating (referred to M4 core material; see
100V ac
BLACK BLUE
14 below).
10. Core must not saturate at 20% over nominal primary voltage. B: 125mm max ORANGE ORANGE
(may have 5mm 'bulge' for leadouts & sleeves) LEADS EXIT NEAR TOP 17Vac @ 100mA*
11. Temperature rise to be less than 60°C at 30% duty cycle (referred to 100V
input voltage and On-Load current). 100V ac BLUE
GREEN 17Vac @ 100mA*
A: 55mm max
ORANGE
Mechanical Specification
---------------------------------------------------
WHITE
12. Primary wires self-ended and individually sleeved, then sleeved together. 3.2Vac @ 55mA*
Secondary wires self-ended and individually sleeved. Low power secondary WHITE
centre tap to share common sleeve. Use PVC sleeving.
+Vout +Vout
BLACK + WHITE GBU8D 8A 200V
Input Voltage (parallel primaries) 100V 115V
+
6800uF
On-Load Current 6.0A 6.0A
63V
BLUE Min On-Load Trough Voltage 41 +1.5/-0 V - Peak Voltage
Load
Off-Load Current - 100mA Trough Voltage
+
6800uF
63V
Max Off-Load Peak Voltage - 63V
0V (Black + White)
-Vout
DRAWING TITLE
100V DiVA A80 Power Transformer
Filename: L917TX_1.0.Sch
Notes:
x3
23
3 x4
33
15
24 x2
IV
17 x2
16
25
14
35
29
II
36 32
22
37
18 AROUND 27 x8
PRIMARIES
7
I
20 x7
III
30
29
27 x5 21 x2
19 32
I
x2
22
28 32
5 IV
x2
27
INTO SUB-PANEL
I 6 4
INTO CONNECTOR
ON PCB
34 x3 ONTO LED'S
12
10
III
26 x4
27 x9
13 x10
8
31
1
11
9 x4
A80 Mechanical and packing parts list
Part No Item No Description
GENERAL MECHANICAL PARTS
E119AY 4 Diva A80 Rear Panel And Silk Screen Assembly
E139AY 5 A80 Chassis Assembly
E83001 7 Gasket Transformer M01/0158
E869PM 8 Button Tact Switch Power Diva
E879PM 9 Foot Black Diva
E891PM 11 Knob A80 Volume & DT81 Selector
E896PM 12 Button DT81 (MODIFED SHANK) Select Button
E897PM 13 Button DT81 Confirm Button (MODIFIED SHANK)
E917HK 14 Heatsink Diva A80 Amp - Using E908EX, A85
E920MC 15 Diva A85/P85 Heatsink Clamp
E954MC 16 Koolpad O/P Device Diva A80 Used ON Heatsink
E956MC 17 Clamp A80 Transistor
HA3V10A 20 M Screw Torx M3x10MM ST ZP
HA3V10B 21 M/C Torx M3X10 Black (500)
HA4A12B 22 M Screw Pan Supa M4x12MM ST BLK
HA5K60A 23 Bolt Hex HD M5x60MM ST ZP
HA5L20B 24 M/C Hex HD. Bolt M5-0.8X20MM Steel - Zinc Black Passivate
HA6K55A 25 Bolt Hex HD M6x55MM ZP
HE6V06B 26 Screw Sftp Torx No.6x6MM BLK
HF4V09B 27 Screw Self-Tapping-Sems NO.4 X 9MM Pan Torx-Slot Steel Zinc-Plate BLK
HJ3A00F 28 M3 Hex Nut Nyloc
HJ4A00A 29 Nut M4 Full ST ZP
HJ4C00D 30 Nut M4 Waisted BR SC
HJ9A01E 31 Hex Half Nut M9
HL4SB 32 Washer M4 Int Shakeproof BLK
HL5EB 33 Washer M5 ST BLK
K5406 34 Sleeve For Light Pipes
L822CA 35 Cable Flat Flex 22WAY 300MM
L933CA 36 5 Way Amp CT 100MM
L916TX 37 115/230 VAC Toroid transformer
L917TX 37 100 VAC only Toroid transformer
L943AY A80 Main cct board & Display cct board PCB Assembly
BLACK CASE PARTS
E845CPB 2 Cover Black DiVA A80/P80
HA4V06B 3 M Screw Torx M4x6MM ST BLK
E189AYB 1 DiVA Black A80 Fascia Complete Assembly
Made up of the following parts :-
E820AP Pad Adhesive Diva DT81 Display Window
E190AYB Front Panel Assembly Black Diva A80
E855MC Diva Black End Cap Low
E917PM Display Window For Diva A80
E871PM Lightpipe Power Diva
E878PM Lightpipe Power Surround Diva
E827SP Sub-Panel Diva A80 Amp
PACKAGING MATERIAL
E948SL Diva A80 Integrated Amplifier Carton Label
L813RC Remote Control Handy 3 Diva Series CR389
SH117 Handbook Diva A80/P80 Amplifier Multi
E922PK One-Piece inner printed DiVA Carton with Integral Partition
E928PK Single generic DiVA End Cap
E888PM Blanking Plug For 4MM Binding Post
E929PK Single heavy DiVA right hand End Cap
P80 Mechanical and packing parts list
Part No Description
GENERAL MECHANICAL PARTS
E917HK Heatsink Diva A80 Amp - Using E908EX, A85
E139AY A80 Chassis Assembly
E879PM Foot Black Diva
HA3V06A M Screw Torx P/H M3x6MM ST ZP
HA4A12B M Screw Pan Supa M4x12MM ST BLK
HJ4A00A Nut M4 Full ST ZP
HA6K55A Bolt Hex HD M6x55MM ZP
HF4V09B Screw Self-Tapping-Sems NO.4 X 9MM Pan Torx-Slot Steel Zinc-Plate BLK
HL4SB Washer M4 Int Shakeproof BLK
HL5EB Washer M5 ST BLK
E121AY Diva P80 Rear Panel And Silk Screen Assembly
E869PM Button Tact Switch Power Diva
8K006 Connector 14MM Shorting Bar P2148
F018 Grommet For Shorting Link
HA5K60A Bolt Hex HD M5x60MM ST ZP
E83001 Gasket Transformer M01/0158
E920MC Diva A85/P85 Heatsink Clamp
E954MC Koolpad O/P Device Diva A80 Used ON Heatsink
E956MC Clamp A80 Transistor
HA5L20B M/C Hex HD. Bolt M5-0.8X20MM Steel - Zinc Black Passivate
HE6V06B Screw Sftp Torx No.6x6MM BLK
L822CA Cable Flat Flex 22WAY 300MM
E897PM Button DT81 Confirm Button (MODIFIED SHANK)
HJ3A00F M3 Hex Nut Nyloc
HA3V10B M/C Torx M3X10 Black (500)
L916TX 115/230 VAC Toroid transformer
L917TX 100 VAC only Toroid transformer
L944AY P80 Main cct board & Display cct board PCB Assembly
BLACK CASE PARTS
E845CPB Cover Black DiVA A80/P80
HA4V06B M Screw Torx M4x6MM ST BLK
PACKAGING MATERIAL
SH117 Handbook Diva A80/P80 Amplifier Multi
E922PK One-Piece inner printed DiVA Carton with Integral Partition
E928PK Single generic DiVA End Cap
E947SL Diva P80 Power Amplifier Carton Label
E888PM Blanking Plug For 4MM Binding Post
E929PK Single heavy DiVA right hand End Cap
F236 Snap Latch Plunger
A80 L943AY_5.0.0 ASSEMBLY DRAWING
Rubber 13/16 inch ID O-rings to be placed around main power supply capacitors C228, C229, C230 A80 Default Jumper Settings (circled on drawing):
and C231. O-rings to be situated midway between PCB and top of cap. CON300, CON301 NOT FITTED
CON302, CON303 FITTED
One whole sorbothane piece to be fitted to top of each of output relays RLY100 and RLY101. CON304, CON305 PINS 1 & 2
CON306, CON307 PINS 1 & 2
One half piece of sorbothane to be fitted to top of each of C386, C387, C388 and C389. CON400, CON500 BIAS SET (AT ARCAM)
CON601 FITTED (NOT FITTED TO PROGRAM A80)
CON602 NOT FITTED (FIT TO PROGRAM A80)
CON700, CON701 NOT FITTED
CON702 NOT FITTED
P80 L944AY_5.0.0 ASSEMBLY DRAWING Insert IC socket IC603-1 into PCB for soldering.
Insert programmed IC603 into socket.
D215 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D300 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D301 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D302 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D303 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D304 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D305 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D306 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D307 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D308 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D309 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D310 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D311 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D312 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D313 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D314 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D315 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D316 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D317 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D318 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D319 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D320 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D400 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D401 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D402 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D403 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D404 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D405 3B4003 Diode 1N4003 DO-41 Package
D406 3B4003 Diode 1N4003 DO-41 Package
D407 3B4003 Diode 1N4003 DO-41 Package
D408 3B4003 Diode 1N4003 DO-41 Package
D409 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D500 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D501 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D502 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D503 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D504 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D505 3B4003 Diode 1N4003 DO-41 Package
D506 3B4003 Diode 1N4003 DO-41 Package
D507 3B4003 Diode 1N4003 DO-41 Package
D508 3B4003 Diode 1N4003 DO-41 Package
D509 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D600 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D601 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D602 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D603 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D608 3F54S Diode Schottky BAT54S SOT-23 Package
D700 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D701 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D702 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D703 3AV99W Diode Dual Surface Mount Small Signal BAV99 SOT-23 Package
D704 3F54S Diode Schottky BAT54S SOT-23 Package
D800 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D801 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
D802 3AS16W Diode Surface Mount Small Signal BAS16W SOT-23 Package
DBR200 3BGBU8D Diode Bridge Rectifier GBU8D Plastic Package 8A 200V
DBR201 3BGBU8D Diode Bridge Rectifier GBU8D Plastic Package 8A 200V
DBR203 3BDF01M Diode Bridge Rectifier DF01 Plastic Package 1A 100V
DISP800 B1016 Display VF 10 14-segment 6mm Characters
DZ200 3CW35V6 Zener Diode 0.25W Surface Mount BZX84C5V6 SOT-23 Package
DZ400 3CW322V Zener Diode 0.25W Surface Mount BZX84C22V SOT-23 Package
A80 Amplifier main/display cct board L943AY issue 5.1
P80 Amplifier main/display cct board L944AY issue 5.1
DZ401 3CW322V Zener Diode 0.25W Surface Mount BZX84C22V SOT-23 Package
DZ402 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ403 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ404 3CW315V Zener Diode 0.25W Surface Mount BZX84C15V SOT-23 Package
DZ405 3CW315V Zener Diode 0.25W Surface Mount BZX84C15V SOT-23 Package
DZ406 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ500 3CW322V Zener Diode 0.25W Surface Mount BZX84C22V SOT-23 Package
DZ501 3CW322V Zener Diode 0.25W Surface Mount BZX84C22V SOT-23 Package
DZ502 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ503 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ504 3CW315V Zener Diode 0.25W Surface Mount BZX84C15V SOT-23 Package
DZ505 3CW315V Zener Diode 0.25W Surface Mount BZX84C15V SOT-23 Package
DZ506 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ600 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ601 3CW33V9 Zener Diode 0.25W Surface Mount BZX84C3V9 SOT-23 Package
DZ602 3CW34V7 Zener Diode 0.25W Surface Mount BZX84C4V7 SOT-23 Package
DZ603 3CW34V7 Zener Diode 0.25W Surface Mount BZX84C4V7 SOT-23 Package
DZ604 3CW34V7 Zener Diode 0.25W Surface Mount BZX84C4V7 SOT-23 Package
DZ700 3CW315V Zener Diode 0.25W Surface Mount BZX84C15V SOT-23 Package
DZ701 3CW34V7 Zener Diode 0.25W Surface Mount BZX84C4V7 SOT-23 Package
DZ800 3CW322V Zener Diode 0.25W Surface Mount BZX84C22V SOT-23 Package
DZ801 3CW35V6 Zener Diode 0.25W Surface Mount BZX84C5V6 SOT-23 Package
FHLDR200 8S004 Fuseholder 20MM PCB
FHLDR201 8S004 Fuseholder 20MM PCB
FS200/201 C56225 115/230 vac units T2.5A fuse
FS200/201 C54232 100 vac fuse T3.15A fuse
FS202 C3501 Fuse Littelfuse T500mA SM
FS203 C3202 Fuse Littelfuse T2A SM
FS204 C3202 Fuse Littelfuse T2A SM
HS200 F007 Heatsink TO-220 6043PB 23 Degc/W Clip ON
HS201 F008 Heatsink TO-220 SW50-2 8.8 Deg C/W
HS202 F007 Heatsink TO-220 6043PB 23 Degc/W Clip ON
IC300 5S408DY IC Analogue Mux DG408DY SO-16 Package
IC301 5S408DY IC Analogue Mux DG408DY SO-16 Package
IC302 5S408DY IC Analogue Mux DG408DY SO-16 Package
IC303 5S408DY IC Analogue Mux DG408DY SO-16 Package
IC304 5B072D Opamp TL072CD SO-8 Package
IC305 5B072D Opamp TL072CD SO-8 Package
IC306 5B2114M Opamp NJM2114M DMP-8 Package
IC307 5B2114M Opamp NJM2114M DMP-8 Package
IC308 5B2114M Opamp NJM2114M DMP-8 Package
IC309 5A2310 IC Audio Digital Stereo Volume Ctrl
IC400 5B072D Opamp TL072CD SO-8 Package
IC500 5B072D Opamp TL072CD SO-8 Package
IC600 5K7400 IC Quad 2-INPUT Nand Gate 74HC00D SMT
IC601 5K7414 IC Hex Inverting Schmitt Trigger 74HC14 SMT
IC602 L027AY Programmed H8HD64F3664FP With Software For A80
IC603 L028AY Programmed HT48R30A-1 With Software For P80
IC603-1 8S028N IC Skt 28PIN 0.3IN
IC604 5G2402 IC Eeprom I2C 2kbit SO-8 Package
IC700 5B324D Opamp Quad ON Semi LM324D SO-14 Package
IC701 5K4040 IC 12-STAGE Binary Ripple COUNTER74HCT4040D SMT
IC703 5K7474T IC Latch 74HCT74D SMT
IC800 5H6351 IC VFD Driver PT6351
IC801 5H809308 IC Micro Reset LM809M3-3.08 SOT-23
ITEM100-1 L943PB Blank PCB Diva A80 Amp
ITEM101-1 F205 Tape D/Sided 12MM X 70MM DS Polyester 4965
ITEM102-1 8M101 Earth Lead Assy 75MM
ITEM103-1 E802AP Pad Damping 15x6x3MM Sorbothane
ITEM103-2 E802AP Pad Damping 15x6x3MM Sorbothane
ITEM104-1 F232 13/16 inch O-Ring
A80 Amplifier main/display cct board L943AY issue 5.1
P80 Amplifier main/display cct board L944AY issue 5.1