Professional Documents
Culture Documents
PROJECT :
LOCATION :
SUBJECT :
ii
iii
iv
vii
viii
ix
xi
xii
xiii
ix
xi
xii
xiii
xiv
xv
xvi
xvii
Notes:
M/s. Space Matrix Design Consultants Pvt Ltd., Page1 of Contractor's Seal Signature
GN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
M/s. Space Matrix Design Consultants Pvt Ltd., Page2 of Contractor's Seal Signature
GN
30
31
32
33
34
35
36
37
10
11
12
13
14
M/s. Space Matrix Design Consultants Pvt Ltd., Page3 of Contractor's Seal Signature
GN
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
M/s. Space Matrix Design Consultants Pvt Ltd., Page4 of Contractor's Seal Signature
GN
10
11
M/s. Space Matrix Design Consultants Pvt Ltd., Page5 of Contractor's Seal Signature
GN
10
11
12
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
M/s. Space Matrix Design Consultants Pvt Ltd., Page6 of Contractor's Seal Signature
GN
10
11
12
M/s. Space Matrix Design Consultants Pvt Ltd., Page7 of Contractor's Seal Signature
GN
These general notes are applicable for all work in this contract.
This work is to be read in conjunction with the Drawings, Specifications, Preambles to Work Sections and General
Condition and Preliminaries in BOQ which shall be construed as being complementary to one another. Any
discrepancy discovered should be reported to the Engineer before commencing work. The words 'as specified'
wherever used in this work shall mean as specified in the above stated documents.
This work is wholly PROVISIONAL and is subject to final remeasurement on completion of the Works.
Unless otherwise specified, method of measurement shall be in accordance with IS 1200.Measurement to be done
with laser digital measurement for measurement and marking
The description provided are brief. The Contractor shall inspect the site, STUDY THE DRAWINGS AND DETAILS
and fully determine for himself the full scope of each item and price the same accordingly. No claim shall be
permissible for lack of knowledge on Contractor's part in pricing of these items.
The work shall be carried out as per drawings, specifications, the description of the items in the schedule and / or
architects instructions.
Items of work provided in this schedule but not covered in the specifications shall be executed strictly as per
instructions of the project manager/architect.
Rates quoted must have full compliance with the following including the cost of grey cement, Cement mortar and
white cement.
The owner reserves the right to supply or issue price basis for any material item.
The owner reserves the right to 'lend' his name for all imported items in order to avail any possible duty
exemptions and the said benefit shall go to the owner.
The items which are supplied free of cost need to be reconciled at the end of the project based on material
constraints.
Special attention to be paid to Technical specifications.
Basic rate shall material to include (Material cost, transportation, delivery and handling charges (delivered
at site).
Upon receipt of majority of good for construction ( GFC ) Drawings, the contractor has to do a re-qualification of all
the items in this bill of quantities and shall get approved by project manager. All rate only items and items which
exceed
Only itemsthiswhich
BOQ are
needs to be and
present addressed
quantifiedandinsubmitted
this BOQ to the be
Shall project manager
considered forfor approval.
payment. The Contractor shall
prepare and submit to project manager a variation order for items excluding this BOQ,operation of rate only items
and
The non tendered
Quantities items ininorder
furnished to of
the Bill beQuantities
consideredare fortentative
payment. / Indicative and the probable quantities is liable to
alterations,omissions or additions and it may vary on the higher or lower side at the sole discretion of the Project
Manager
All concrete/ Owner.
works to be design mix and the contractor shall quote the rate as per minimum cement requirement
specified in the respective mix in the Bill of Quantities. If any variation of cement contents in the execution will be
considered
Any claims, only for reconciliation
disputes in the quotedbut not and
rates for payment.
extra items at later stages will not be entertained outside the scope of
above.
No asbestos - containing material in construction materials to be used by vendors / contractors.
Rates quoted must include protection for Staircase steps, passenger lift and service lift
The contractor is to note and allow the following preambles in his scope of work.
Granite slabs should be free of all defects and all grains / patterns shall be properly matched from the same lot.
Any colour / lot variation shall be rejected.
Please refer all detailed drawings for flooring and cladding works of stone to understand the variation in size of the
stone slab at the periphery or anywhere as per design and site condition.
M/s. Space Matrix Design Consultants Pvt Ltd., Page8 of Contractor's Seal Signature
GN
All Granite to be locally sourced and supplied unless and until specified in the drawings.
The vendor to consider undulance tolerance code as per IS Code for all civil works
For all 'hard flooring areas',(areas with Granite / marble/ceramic-vitrified tiles/etc,) only the 'laid area' (visible after
complete laying, etc.) shall be paid for. No 'extra' shall be paid for cutting / wastage / etc.
All 'inlays' in the flooring shall be paid for as per relevant item(s) in RMT. If, as per design, any 'module' of
the relevant inlay, (width / length) has to be executed at site and the same is not conforming to / with the
specification(s), the rate shall be derived on a prorata basis from the quoted rates.
All stones mentioned in the tender shall be brought to site only from the lots pre-approved /selected by the
architects.
Rates quoted for items of counter, etc. shall be inclusive of making necessary cutouts for sinks, basins and
inclusive of polishing the cut edge to the profile as indicated on the drawings, to the entire satisfaction of the
supervising architects.
All masonry and plastering works shall be sufficiently cured, to the entire satisfaction of the supervising architects,
before taking up finishing works on the same.
Rates quoted for the treads of the staircases shall be deemed to be inclusive of making all necessary cutouts, for
railing balustrades, etc., in 'workmanlike manner, and, to the entire satisfaction of the supervising architects
All Samples of tiles, fittings etc. Shall be presented after ensuring that the necessary quantities of the relevant
item(s) for which the same are invited are available, (ex-stock, or otherwise) and shall be approved by the architect
before
Vitrifiedplacing of mass
tile / ceramic orders.
tiles shall be flat and true to shape and free from cracks, crazing spots, chipped edges, even
color and corners. The tiles shall be of nominal sizes such as 600mm x 600mm size ( or as size specified) and of
colour and shade as approved/specified. They shall be of one consignment/lot.
The acid resistant tiles shall be as per the manufacturer’s specifications.
All the Dado and/ Flooring shall include rates of the 6mm thk spacers with colour matching grouts and
Edge Guards of
All appointed matching
agencies arecolor of the
required todado
ensurewherever thescope
that their wallsof
are in right
works areangles, as per
undertaken ininstructions
an absolutely/
related specifications
professional towardsmanner
and workmanlike the same, asfurthermore,
and, provided by to theensure
consulting architects
that 'housekeeping' activities are
undertaken , at the site / premises in question in such a manner that no debris/rejected materials/etc. are
retained at site in a disorderly manner, failing which, the Clients/Architects shall be at liberty to take
remedial action at the
Daily housekeeping soleareas
of work cost(s) andincludes
which consequences of the
segregation of appointed contracting
debris like cement agency
based, plastic, glass, wood
and collecting in containers provided to/by you, at an acceptable location inside the site premises.
All floor surfaces receiving the appropriate flooring material(s) need to be thoroughly cleaned prior to installation of
the desired flooring.
No allowances shall be made to undertake rectification works if the same are so desired to be undertaken for
improper adherence to recommended application procedures / standards.
All joints, wherever necessary, shall be undertaken after prior approval of the same from the Architects.
All finished flooring surfaces shall be free from bubbles/scratches/stains/etc. prior to final hand- over of the activity
at the desired locations. All finished flooring shall be covered with plaster of Paris of 6mm thick over a plastic film
without any extra cost till handing over to the Owner.
All materials utilised shall be as per tender recommendations and shall be applied according to manufacturer's
specifications.
Plastering rates to include Expanded metal mesh ( 24 gauge) of approved make which shall be provided at
the Junctions of masonry and concrete surfaces of 150mm wide on either side of the junction in double
fold stretched and nailed properly prior to plastering.
Receiving all materials supplied by the Owners / your vendors, unloading, storing at location specified by the
project manager. No additional payment will be paid for any increase lead from this location conveying to work site
&
Thefixing in position.
minimum quality benchmark will be decided by the Owner / Project manager / Architect based on mock up
samples before commencing the work.
Unless otherwise specified the rates quoted shall include only the following ~ Cost of material, transport and
labour. Overheads and profit shall be indicated separately as per bid summary sheet.
The basic rate of granite/marble/vitrified/ ceramic / etc., includes supply and delivery to site of approximately 8' x
4' ( granite / marble ) random slabs (or larger) delivered and unloaded to the point of cutting the same. All granite
material
If there isshall be "gang
a reduction is saw waterrate
the basic cut".the cost for the same shall be adjusted pro rata in the quoted rates. No
increase in basic rates shall be allowed without written approval from the Architect.
Base sub-grade/sub-floor to be prepared by cleaning all dust/loose particles, caked mortar droppings, etc by
scrubbing with steel wire brushes. Surface to be roughened if so required and surface cleaned with water and kept
wet for minimum
Bedding 12 hours.
layer of mortar to be provided as directed in the case of 19mm + slabs to correct level, step as instructed.
M/s. Space Matrix Design Consultants Pvt Ltd., Page9 of Contractor's Seal Signature
GN
Contractor to be responsible for hiring/operating of all machines/equipment. Approval to be obtained from Project
Manager before operating.
Finished floor must be cured by keeping wet for atleast 1 week after installation.
All granite / marble flooring slabs to be polished using tin oxide only.
In the instance of granite/marble floors, the contractor has to obtain prior approval on dry laying. Wet laying to be
carried out only on approval. Not extra cost shall be paid for dry laying.
General Notes-Interior
The rates for all tiles, slabs of marble, granite, Kota or any other stone should be inclusive of all materials,
transport, loading unloading, Octroi and all taxes thereon. The rate mentioned is the maximum and in no way
should exceed, the one mentioned.
The door size mentioned is the overall opening size.
The contractor should refer to the detailed drawings for details. All the rates so quoted should be inclusive of all
hardware. In case of discrepancy between drawing and Bill of Quantity the drawing supersedes, unless specifically
mentioned in the BOQ , before executing the works should be highlighted to the architect for approval.
Rates for all exposed wooden members and lipping shall include cost of melamine finish.
The rate of all units to be inclusive of approved locks for individual work space every drawer and shutter to be
provided with locks of approved make.
Details of the items under this schedule shall be read in conjunction with the corresponding specifications,
drawings and other Tender Documents.
The work shall be carried out as per drawings, specifications, the description of the items in the schedule and / or
architects instructions.
Items of work provided in this schedule but not covered in the specifications shall be executed strictly as per
Unless specifically
instructions mentioned
of the project otherwise in the contract, the tenderer shall quote for the finished items and shall
manager/architect.
provide for the complete cost towards labour, materials, plant and machinery, operational costs, levies, taxes,
transport,
The repairs,
quantities rectification,
of the maintenance
various items mentionedtillinhanding over, revenue
the schedule expenses,
in the schedule contingencies,
of items overheads,
are approximate profits
and may
and
vary all
upincidental items
to any extent ornot
be specifically mentioned
deleted altogether. but reasonably
he quoted rates of implied andshall
each item necessary
remain to complete
firm for boththe
theworks
variation
according to the The
and extra items. contract.
contractor, in his own interest, should get an indication of the probable extent of the work to
be executed under any particular item in this schedule, before undertaking any preliminary and enabling work or
Project managers
purchasing bought/ out
architects decision
components shall to
related bethe
final and binding on the contractor regarding clarifications of items
work.
in this schedule with respect to the other sections of the Contract.
It may be noted that the total work or any part / parts of the same may be awarded as mentioned in this schedule
of items.
The rates quoted shall be inclusive of all mock-ups, associated samples prior to any mass production or
procurement as per complete satisfaction of the Client and Architect. Inclusive of dismantling, demolition and
carting the material
All services works,and anymaking good
interface of thewith
works surface.
other vendors have to be completed before finishing of
partition paneling, other wall finishes and false Ceiling works. Signoff shall be taken from the Engineer in
charge before proceeding with the final finishing works.
TYPICAL NOTES - PARTITIONS
All cross sections of timber mentioned in the specifications for the frame works of the partition shall be of desired
type, free from knots/variations/indentations/etc., and, shall be with moisture content, if so, upto acceptable limits,
free from warpage and bends, upto desired lengths, and, shall be finished sizes, and, from lots, or as ,(pre)
approved
In case of bytwothe architects.
levels of false ceiling abutting the partitions on either side, the height of the partition shall be
measured upto the higher false ceilings.
In case of stepped ceilings abutting the partitions on the same side, then the higher of the two shall be measured
for the height of the partition if the taller portion of the partition is more than 1/2 the length of the partition. If not
then the
Rate two portions
quoted of the partition
for the partitions shall beshall be measured
inclusive separately.
of pre-approved anti termite treatment for the frames in case of
timber frames; application of the same,(mode of application/number of coats/etc.) shall be as per and conform with
the
Ratesrelated
quotedmanufacturer's
for full heightspecifications.
partitions shall be inclusive of insulation of glass wool/ rock wool / thermocol(of pre-
approved grains/massing, as specially required/recommended by consultants, for acoustic purposes) as specified
unless mentioned otherwise.
M/s. Space Matrix Design Consultants Pvt Ltd., Page10 of Contractor's Seal Signature
GN
Rates quoted for the partitions shall be inclusive of making cutouts for Electrical and Data outlets and for making
provisions for passing conduits through the framework.
Rates quoted for partitions shall be inclusive of additional vertical or horizontal frame members as required for
skirting, fixing soft board, white board, projection screens etc fixing of elec. Boxes etc. apart from the regular
framework members @ 600mm c/c bothways.
Any/all inserts/grooving and laying patterns shall be as per architects specifications and shall form part of the
relevant paneling detail(s) and shall not be paid for extra, unless otherwise specified/mentioned
Vendor to be provided extra GI Noggin channel & ply support wherever the LCD TV is coming as per the detail
drawings/architect's & PM's Instructions.
Vendor to provide extra additional GI Members / aluminium sections / Salwood sections for where the height of
partition is coming above 3m.
Vendor to provide necessary fire sealant filling wherever required in the walls/partitions as per the PM's / architects
instructions.
Contractor to make provisions of all necessary scaffoldings to facilitate high level installations.
Contractor to form openings on partition for services and to seal gaps using silicone sealant.
For partition frame work : 16/8 no. sheet metal screw 16mm in length.
For partition anchoring on floor & true ceiling : 75/10 no. sheet metal screw 75mm in length.
Quoted rates shall include transport, customs clearing, lead, lift, installation, rectification of defects or replacement
of defective material.
Storing, safe guarding of the supplied material shall be the scope of the vendor till handing over.
All glass to be of best quality of approved manufacture, and be free from bubbles, smoke wanes, air holes and
other defects. It is to accord with the indications given on the Material Selection Schedule.
Tempered glass shall have structural integrity and shall not contain any harmful scratches, pinholes, unevenness,
sharp angled or field edge.
On completion, all glass shall be cleaned both sides and any broken, cracked or defective panes shall be replaced
at Contractor’s own expense.
Glazing to be delivered to site in cut sizes, in packages bearing the manufacturer’s name and/or trade mark. The
type, quality, thickness or weight of the glazing is to be clearly marked on the package.
In cutting glass, proper allowance shall be made for expansion. Each square of glazing to be as large as possible.
Glazing is to comply with requirements of BS Code of Practice 152. All glass edges to be properly machine ground
and polished.
On completion, clean all glazing, replace all cracked, scratched or broken sections and leave in good condition to
the satisfaction of the Designer.
Gaskets for glazing shall be preformed rubber gaskets to BS4255 Part 1 on approved neoprene gaskets, to be
used strictly in accordance with the manufacturer’s printed instructions.
The Tender shall be read in conjunction with the General Conditions & Preliminaries, Bill of Quantities /
Specification of Materials & Workmanship, Drawings and all other documents part of the Tender which shall be
If the Vendor
construed shouldcomplementary
as being find any discrepancy
to onein the Drawings or between the Drawings and the Bill of Quantities /
another.
Specification of Materials and Workmanship or any other Documents forming part of the Tender, she/he shall
immediately refer the same at the time of pre-bid meeting to the Architect and same shall be clarified on, if not the
Vendor shall not be liable for any further additional claim.
It will be the vendors responsibility to hand-over the installed Glass to clients/owner free of defects.
Lamination of glass shall be done using DuPont make acoustic PVB laminated only.
Payments shall be on Actual Installed quantities, Face elevation area is considered for measurements.
Scaffolding at shaft door areas to move from floor to terrace level to be included in the part of the rates
M/s. Space Matrix Design Consultants Pvt Ltd., Page11 of Contractor's Seal Signature
GN
The Fabric paneling / other paneling should be free from odour. Care has to be undertaken for the same. After execution any defects happens, vendor has to provide the appropriate solutions for the same. The rework cost will not payable.
For all Flush Doors mentioned in the specifications, approved brand Flush doors only shall be used.
The door frame sizes mentioned in the specifications shall be finished sizes of Timber.
All door frames fixed to partitions shall be embedded into the floor, in workman like manner, by atleast 38mm for
rigidity. The rates quoted for the door frames shall be inclusive of this extra length required.
All Door frames to be fixed to masonry in proper plumb and in workman like manner, and shall be inclusive of
desired number of hold fasts, per door, as specified, and all other hardware is required to fix the same, and upto
the entire satisfaction of the Architects.
The thickness of the flush door mentioned in the specifications shall be bare thickness of the flush door exclusive
of finishing
Rates quoted for the doors shall be inclusive of all hardware as specified in the specifications. Individual rates of
the hardware as asked for, shall be operated and the difference in the cost payable to the contractor in case of
alternate
All hardware
doors shall be ofbeing chosen
standard by the
32 mm architect/client
to 38mm thicknessduring
unlessexecution.
otherwise specified. In case of concealed door
closures mentioned in the specifications the doors shall be min.42mm thk (even if not specified). Rates to be
quoted accordingly.
Rates quoted for hardware shall be assumed to be quoted for based on the thickness of the door especially in
case of cylindrical locks. No extra shall be paid for in case longer cylinders need to be used in case of thicker
doors.
In case of variation in door and door frame sizes from those mentioned in the specifications, the rates shall be
arrived at on a prorata basis on the sizes.
All job works to be undertaken according to design / details, in workman like manner and to the entire satisfaction
of the supervising Architects.
All door locks to have a master key
All tables shall have provision for Wire management as per design and detail.
If required and instructed by the architect, the wire management system of the table shall be separately bought out
and fitted on to the table as per design and detail.
All tables to be finished in workman like manner upto desired and approved finishing standards, failing which, the
same shall be undertaken and achieved by the Architects at the sole risk and responsibility of the concerned
Contractors.
All tables to be factory finished
All storages unless otherwise mentioned in the item specifications shall be 450mm depth to 600mm depth.
All internal surfaces of cabinets, etc in conventional carpentry works shall be finished with 0.8mm thick matt
finished laminate of approved shade
M/s. Space Matrix Design Consultants Pvt Ltd., Page12 of Contractor's Seal Signature
GN
All under surfaces of furniture (tables, counters, etc) to be finished with 0.8mm thick matt finished laminate of
approved shade
All exposed horizontal laminated surfaces shall be finished with 1mm thick laminate of approved make shade
unless otherwise specified.
All exposed vertical laminated surfaces shall be finished with 1.0mm thick laminate of approved make shade
unless otherwise specified.
Storages shall be inclusive of approved hardware, brushed steel handles, tower bolts, ball catches, SS hinges of
approved make even if not explicitly mentioned in the specifications unless specifically mentioned otherwise.
If so specified by the architect during the progress of works at site, the storages shall be fabricated outside the site
and brought to the site and placed at instructed locations. No extra shall be payable for the transportation of
theexposed
All same. edges of ply / board etc. shall be finished with lipping Patti of TW of required size & All margins to be
finished with colour polish to match Laminate / Veneer. This shall apply for the carcass, shutters of the storages
and shelves if any.
All storages should be factory finished.
All internal woodwork shall be treated with anti termite and fire retardant paint where
All exposed veneer shall be group matched natural cut plain veneer of approved make and shade.
All exposed veneered, wood surfaces shall be finished with matt melamine polish to approved shade
All exposed edges of plywood, blockboard etc shall be finished with 3mm thick lipping beading of specified wood
All plywood, blockboard for office areas shall be water resistant, termite/borer proof commercial grade of specified
make.
All plywood, blockboard for wet areas (toilets/pantry) shall be termite/borer proof and waterproof marine grade of
specified make.
Timber used shall be kiln seasoned and should be free from shrinkage, warpage even after fabrication of furniture.
Provision to be made for additional supports and reinforcement that may be required for stability and evenness at
where curved partition is constructed
Where the use of spring loaded auto closing hinges is specified, the same shall be installed strictly as per
manufacturers guidelines and relevant tools required for the same.
All items to have sample approved prior to commencement of mass production
For fixing drawer channel : For bottom channel - 19/6 no., For side - 9.5/6 no. sheet metal screw.
For fixing meta box drawer channel : 9.5/6 no. sheet metal screw
For fixing auto closing hinge : 16/6 round Philip head screw.
M/s. Space Matrix Design Consultants Pvt Ltd., Page13 of Contractor's Seal Signature
GN
All job works need to be undertaken as per design / details supplied and to the entire satisfaction of the
supervising Architects.
Contractor to make provisions of all necessary scaffoldings to facilitate high level installations.
Taking care, covering all electrical fixtures with masking tape and removing painting spots from all floor areas,
surrounding areas, glass, walls, etc. complete. Leaving the premises clean and tidy.
Scope of Work shall include furnishing of all materials, equipment and labour to install the complete ceiling system.
It is the contractors/suppliers responsibility to ensure that materials delivered to the installation site as safeguard
from the time of His purchase until he hands over the finished ceiling. It is desirable to store materials in a flat,
clean and dry surface.
It is the contractor's responsibility to store the material as per manufacturer's installation guidelines to avoid any
kind of damage to the men, material, building.
Controlled ventilation should be used to disperse moisture laden air.
Ceiling system shall be installed by a sub contractor thoroughly experienced with this type of installation and
approved by the manufacturer. The contractor to inspect premises prior to commencement of work and verify that
the building is ready for installation.
Dust and loose particles should be removed by brushing or with a vacuum cleaner. Any pencil marks etc can be
removed using ordinary pencil eraser. All damaged tiles to be replaced.
Spot lights and other luminaries should not be supported by or on the ceiling tiles.
Suspension wire / rod must be Galvanised of diameter not be less than 3mm to 4mm. The rod shall always be
mechanically pre- straightened.
Finished area shall be measured in length & breadth for payment.
Quoted rate shall include making cutout for light fixture, diffuser or any other service cutouts.
Vendor to the submit samples, shop drawings and get the approval from the Architect/Designer before the
production.
M/s. Space Matrix Design Consultants Pvt Ltd., Page14 of Contractor's Seal Signature
GN
M/s. Space Matrix Design Consultants Pvt Ltd., Page15 of Contractor's Seal Signature
MEP APPROVED MAKE LIST
Sl No EQUIPMENTS MAKES
HVAC
1 VRF SYSTEM BLUE STAR / DAIKIN
DOL STARTER PANEL / SEQUENTIAL
2 CONTROLLER TITATIX / AIRCON / POWER ELECTRONIC SYSTEMS
3 REFRIGERANT PIPING - COPPER TOTALINE / RAJCO / NIPPON / MAXFLOW
4 DRAIN PIPING - CPVC SUPREME / ASHIRVAD
5 DRAIN PUMP ASPEN
6 MOTORIZED FIRE / SMOKE DAMPER - UL 555 GREENHECK / RUSKIN TITU
CERTIFIED
MOTORIZED FIRE / SMOKE DAMPER - UL 555
7 LISTED AIR MASTER / AIR ACTION / SYSTEMAIR
8 MOTORIZED ACTUATORS BELIMO / SIEMENS / HONEYWELL
9 GI SHEETS JINDAL / TATA STEEL / ESSAR
10 WIRE DUCT SUPPORTS GRIPPLE
11 ROD DUCT SUPPORTS HITECH / FISCHER / INDIANA
12 FACTORY FABRICATED GI RECTANGULAR DUCT ROLOSTAR/SA SPIRO / CAM DUCT
13 FACTORY FABRICATED GI OVAL DUCT GP SPIRAL / SPIRAL TUBE / DEV DUCT
14 SPIGOT / BUTTERFLY DAMPERS / GI VCD AIR MASTER / COSMOS/ AIR ACTION
15 NITRILE RUBBER INSULATION (CLOSED / OPEN KFLEX / ARMACELL
CELL)
16 FIBERGLASS INSULATION FOR WALL ACOUSTIC UP TWIGA / OWENS CORNING / KIMMCO
17 INSULATED / UNINSULATED FLEXIBLE DUCT SEVEN STAR / SUPAFLEX / 7 STAR / ATCO
18 NITRILE RUBBER INSULATION - ACOUSTIC / SUPERLON / A FLEX / K FLEX / ARMAFLEX
THERMAL
SUPPLY / RETURN AIR DIFFUSERS / GRILLES /
19 LOUVERS / JET NOZZLES / LINEAR SLIT / SLOT AIR MASTER / AIR ACTION / COSMOS/ VEDHA
DIFFUSER
20 POWER AND CONTROL CABILING POLYCAB / BENTON / RR / ANCHOR
21 POWDER COATED GI CABLE TRAY PUSHPAK / INDIANA / EQUIVALENT MAKE
22 PVC FRLS CONDUITS PRECISION / DIAMOND / VIP
23 VENTILATION FANS CARYAIRE / KRUGER / NICOTRA
24 SOUND ATTENATOR SYNCRO / AIR MASTER / AIR ACTION
25 DOUBLE SKIN PLENUM AAGAM / SKY AIRCON / KANVA COOL
26 STARTER PANEL SHARAN CONTROL / TITANIX / POWER MASTERS
27 FIRE SEALANT 3M / HILTI
28 FABRIC DUCT DURKEESOX / PRIHODA
29 DX. HIWALL UNITS LG / CARRIER / BLUESTAR
BMS
1 IP CONTROLLER & GRAPHIC SOFTWARE HONEYWELL TRIDIUM (Vykon)
2 GRAPHIC SOFTWARE HONEYWELL TRIDIUM (Vykon)
3 SENSORS OMICRON/ GREYSTONE/ DWYER
4 VAV HONEYWELL/TRANE/JCI/TROX
5 CABLES UNIFINE/ EXCEL/VARSHA
6 CONDUITS PRECISION/DIAMOND/VIP
7 CABLE TRAY PROFAB/PUSHPAK/ CLASSIC
8 HYDROGEN SENSOR HNL/KELE/AMBETRONICS/TRITEK/HONEYWELL/ MSR
9 CURRENT RELAY FOR ON / OFF STATUS MINILEC / SITU / KELE / SONTAY / VERIS / SENTRY
10 TOWER LAMP OMICRON/SCHINIDER/ SIBASS/ FINETECH
11 NETWORKING CABLES COMMSCOPE/PANDUIT/BELDEN
10 MANGED NETWORK SWITCHES CISCO
11 MONITORS/TV SAMSUNG/ LG
VAV
1 VAV & THERMOSTAT HONEYWELL/ JCI/TRANE/TROX
2 CABLES UNIFINE/ EXCEL/VARSHA
3 CONDUITS PRECISION/DIAMOND/VIP
4 CABLE TRAY PROFAB/PUSHPAK/ CLASSIC
FIRE ALARM
1 FA COMPONENTS EDWARDS/MIRCOM/NOTIFIER
2 DETECTORS & SPEAKERS ,AMPLIFIER EDWARDS/MIRCOM/NOTIFIER
3 RESPONSE INDICATOR EDWARDS/MIRCOM/NOTIFIER
4 MANUAL CALL POINT EDWARDS/MIRCOM/NOTIFIER
5 HOOTER CUM STROBE EDWARDS/MIRCOM/NOTIFIER
6 CONTROL / MONITOR MODULES EDWARDS/MIRCOM/NOTIFIER
7 CONDUIT VIP/ PRICISION
8 CABLES UNIFINE/VARSHA/POLYCAB/HAVELLS
RODENT & WLD, FLAP BARRIER
1 CONDUIT VIP/ PRICISION
2 RODENT & WLD C SYSTEM/ MASER/RSCAT
3 FLAP BARRIER BOOM EDAM 900 / MAGNETIC CONTROL
4 VESDA XTRALISIS/ SIEMENS/ SECURITON
FPS
1 GI PIPES TATA / JINDAL (HISAR)
VS ENGINEERING/ JK FORGING / BM /INDUSTRIAL
VALVES & COMPANY
2 FORGED FITTINGS
3 PAINTS ASIAN PAINTS / BERGER / ICI
4 SPRINKLER BULB TYCO / SAFEX / VICTAULIC
5 FLEXIBLE HOSE TYCO / SAFEX / VICTAULIC
6 VALVES AUDCO / INTERVALVE / ZOLOTO
7 GSS NOVEC KIDDE / SAPPHIRE / SINOREX
8 FIRE CURTAIN ORIENT
9 EXTINGUISHER SAFEX / KANNEX
SECURITY
1 ACS SOFTWARE, SOFTWARE LENEL
2 CCTV INTERLOGIX/ AXIS/ AVIGILON
3 CONDUIT VIP/ PRICISION
4 CABLES UNIFINE/VARSHA/POLYCAB/HAVELLS
5 COMPONENTS BELL/EAGLE/ MAG
6 READERS HID
ELECTRICAL
1 PVC FRLS CONDUIT PIPE AND ACCESSORIESVIP / PRECISION
2 PVC FRLS FLEXIBLE PIPE VIP / PRECISION
3 MS CONDUIT PIPE AND ACCESSORIES BEC / GUPTA
4 PVC FRLS COPPER CABLES HAVELLS / POLYCAB / KEI
5 PVC FRLS COPPER WIRES HAVELLS /POLYCAB/ KEI
6 SWITCHES & SOCKETS SCHNIEDER LIVIA/MK CITRIC/LEGRAND/HAVELLS
7 DB & MCB's LEGRAND/SCHNEIDER/ABB
8 FLOOR BOX LEGRAND/CONNECT/MK
9 INDUSTRIAL SOCKET NEPTUNE / LEGRAND
10 LT CABLES POLYCAB/KEI / RR / RAJANIGANDHA
11 CABLE GLANDS DOWELLS / COMEX / HMI
12 LUGS DOWELLS / COMEX
13 CABLE TRAY /RACEWAY 2mm tk. REPUTED
14 LIGHT FITTINGS WIPRO/PHILIPS/HAVELLS/LT
15 LIGHT FITTINGS- DESIGNER Purple Turtle /chandra Lmap/ Ripple /AS PER DESIGNER
16 ELECTRICAL PANELS SHARAN CONTROL / LOAD CONTROLS
17 LMS LUTRON/CRESTRON
18 METERS SCHNEIDER/ELMEASURE
19 MCB /MCCB/ISOLATOR SCHNEIDER / ABB /L&T
20 INDICATING LAMPS (LED TYPE) TECKNIC / ABB
21 AUXILLARY CONTACT PLA/OMRAN
22 CTs & PTs KAPPA / KALPA
23 ELR WITH CBCT -MICROPROCESSER BASEDPROK DIVIS
24 TVSS OBO / ABB / SCHNEIDER
25 AUTO CHANGE OVER SWITCH / ATS SOCOMEC / SCHNEIDER
26 DEDICATED EARTHING Ashlok/Gel earthing
27 UPS Vertiv /Socomec
28 PAC Vertiv/Stulz
OMSAI-LOI OMSAI - GFC QTY
Sl. No DESCRIPTION OF WORKS AMOUNT IN INR AMOUNT IN INR
A POWER RECEPTICALS
Supply, Installation, Testing & Commissioning of the following
components of approved make like type of switches, socket
etc,.housed in GI enclosure, duly wired.
B CIRCUIT WIRING
C DISTRIBUTION BOARDS
415V / 240V, 3 Phase / 1 Phase factory assembled totally
enclosed wall mounted, IP43, shall be made out of0.8mm
CRCA sheet enclosure and powder coated complete with
cable gland plate with knock out at the top & bottom. The
shall have double door with hinged lockable external door.
MCB distribution boards shall be as per standard specification
and with electrolytic grade copper busbars for phases and
neutral. Suitable earth links for earthing. The RCCB / RCBO
shall be Hpi / Si-series. MCBs shall be 'D' Curve for UPS related
s (U) and 'C' Curve for other application.
Outgoing
5 Nos, 63A DP ' D ' curve MCB 's
5.02 Supply & Installtion of 16swg Wire way/drawbox/raceways
for DBS sides etc., using MS sheet complete with powder
coated painting hardware, etc., to match DB colour
sq ft 1011 1011 834 843174 834 843174
D LT CABLES
E CABLE TERMINATION
Supply & Installation of 1.1kV grade type Cables termination
using Single/double compression PG cable glands with earth
tags, crimping type tinned copper lugs, earthing clamps
consumables for the following size of cables.
Functional lighting
1.00 Light fixture with HF ballast
1.01 2'x2', 30-35 W LED light fixture for achieveing uniform
horizontal and vertical illumination
no. 129 129 150 19350 150 19350
1.02 20-30W 4 feet direct type suspended LED light fixture no. 29 29 150 4350 150 4350
1.03 18-20W batten type surface/wall mounted LED light fixture no. 34 34 125 4250 125 4250
1.04 9W LED recess mounted round/square downlighter no. 143 143
1.05 15W LED recess mounted round/square downlighter no. 143 143
1.06 14-18W LED suspended mounted cylinder type downlighter
( 200mm height)
no. 705 179 179 125917
1.07 14.4W LED strip light with required driver with al casing and
acrylic diffuser
m 143 143
1.08 14.4W LED strip light with required driver m 200 200 125 25000 125 25000
G.1 POINT WIRING with PVC conduits with 1.5 Sq.mm flexibl
wires
1.00 Supplying and installation of wiring for light points
with/without sensors by using 19mm dia,2mm thick FRLS PVC
conduit of required dia as per IS732, PVC conduit accessories,
PVC flexible conduit with couplers for drops with accessories.
All points shall be earthed with 1.5 Sqmm FRLS flexible copper
wire. Wires shall be terminated at light fixtures with ferrules,
15A 4 way connector; wire ends shall not be loose / bare.
1.01 1 light point controlled by a 6A switch with 1.5Sqmm wire no. 74 74 1,230 91020 1,230 91020
1.02 2 light point controlled by a 6A switch with 1.5Sqmm wire no. 48 48 1,660 79680 1,660 79680
1.03 3 light point controlled by a 6A switch with 1.5Sqmm wire no. 16 16 2,200 35200 2,200 35200
1.04 4 light point controlled by a 6A switch with 1.5Sqmm wire no. 8 8 2,650 21200 2,650 21200
1.05 5 light point controlled by a 6A switch with 1.5Sqmm wire no. 1 1 3,500 3500 3,500 3500
1.06 6 light point controlled by a 6A switch with 1.5Sqmm wire no. 4,216 4,216
1.07 7 light point controlled by a 6A switch with 1.5Sqmm wire no. 4,988 4,988
1.08 8 light point controlled by a 6A switch with 1.5Sqmm wire no. 5,670 5,670
1.09 9 light point controlled by a 6A switch with 1.5Sqmm wire no. 6,262 6,262
1.10 10 light point controlled by a 6A switch with 1.5Sqmm wire no. 6,854 6,854
1.11 1 light point controlled by a 6A switch with 1.5Sqmm wire -
for Emergency lighting
no. 23 23 1,230 28290 1,230 28290
1.12 2 light point controlled by a 6A switch with 1.5Sqmm wire -
for Emergency lighting
no. 22 22 1,660 36520 1,660 36520
H EARTHING
Note : The rate quoted shall include providing earthing for the
Wireway trunking with support hardware. (Usage of jumper
wire at joining is acceptable)
4.01 (60x60x55)mm GI floor junction box with 2 mm thick cover. no. 335 335
4.02 (110x110x55)mm GI floor junction box with 2 mm thick cover.
no. 419 595 350 146650 350 208250
4.03 (160x160x55)mm GI floor junction box with 2 mm thick cover.
no. 146 222 460 67160 460 102120
4.04 (210x210x55)mm GI floor junction box with 2 mm thick cover.
no. 102 128 580 59160 580 74240
4.05 (260x260x55)mm GI floor junction box with 2 mm thick cover.
no. 79 120 660 52140 660 79200
4.06 (310x310x55)mm GI floor junction box with 2 mm thick cover.
no. 86 230 960 82560 960 220800
4.07 (460x460x55)mm GI floor junction box with 2 mm thick cover.
no. 3 150 1,450 4350 1,450 217500
J MISCELLANIOUS ITEMS
1.00 Supply & Installation of 415V enameled type danger boards
150mm x 150mm Size including the cost of fixing
arrangement etc. no. 11 11 250 2750 250 2750
2.00 Supply & Installation of 415V enameled type 2mm thick ISI
mark 1100V grade rubber mat of standard length of 2m x 1m
including the cost of fixing arrangement etc. no. 25 25 2,200 55000 2,200 55000
3.00 Supply & Installation of 415V enameled type Shock treatment
chart duly framed and laminated including the cost of fixing
arrangement etc. no. 11 11 350 3850 350 3850
4.00 Supply & Installtion of A1 size power distribution laminated
SLD in electrical room LS 11 11 2,500 27500 2,500 27500
5.00 Supply & Installation of First aid box complete with all
standard first aid materials. no. 11 11 1,200 13200 1,200 13200
6.00 Removing & refixing of existing basebuilder DB at basebuilder
electrical room located in both 7th & 8th FLoor no. 8 8 1,100 8800 1,100 8800
Execution
The contractor is responsible for the installation of temporary
lighting systems.
The system shall be installed at the earliest and coordinated
with other
construction activities.
8.01 30KVA, 3ph. input, 3ph Output. 215V Set 733,950 733,950
K EMPTY CONDUITS
1.00 Supply & installation of 2 mm thick conduits of following sizes
for open / enclosed wiring complete with all necessary
accessories
1.01 19 mm dia, 2mm thick, FRLS type PVC conduit m 300 300 62 18600 62 18600
1.02 25 mm dia, 2mm thick, FRLS type PVC conduit m 4200 6200 67 281400 67 415400
1.03 32 mm dia, 2mm thick, FRLS type PVC conduit m 20 20 123 2454 123 2454
1.04 20 mm dia, 1.8 mm thick, MS conduit m 116 116
1.05 25 mm dia, 1.8 mm thick, MS conduit m 144 144
L CABLE TRAYS
2.01 (150x50)mm wide cable tray m 870 1118 680 591600 680 760240
2.02 (300x50)mm wide cable tray m 460 720 990 455400 990 712800
2.03 (300x70)mm wide cable tray m 1,079 1,079
2.04 (450x70)mm wide cable tray m 480 480 1,740 835200 1,740 835200
2.05 (600x70)mm wide cable tray m 266 266 2,100 558600 2,100 558600
2.06 (750x70)mm wide cable tray m 80 80 2,580 206400 2,580 206400
M LT PANEL
Supply, installation, testing, commissioning, loading
unloading Shifting upto site of following Electrical Panels
1.00 7F Main W/S UPS Input PANEL - Wing A - C2 Set 1 1 11,500 11500 11,500 11500
2.00 W/S & IT-SB UPS O/P PANEL-1 Set 1 1 6,500 6500 6,500 6500
3.00 CRITICAL UPS O/P PANEL-01 Set 1 5,733 5733 5,733
IT-SA UPS O/P PANEL-01 Set 1 8,000 8000
4.00 SERVER PANEL SA & SB Set 2
5.00 7F W/S UPS O/P PANEL-01 (WING A,TOWER-C1) Set 1 1 3,500 3500 3,500 3500
6.00 7F W/S UPS O/P PANEL-02 (WING A,TOWER-C2) Set 1 1 3,500 3500 3,500 3500
7.00 8F W/S UPS O/P PANEL-01 (WING A,TOWER-C1) Set 1 1 3,500 3500 3,500 3500
8.00 8F W/S UPS O/P PANEL-02 (WING A,TOWER-C2) Set 1 1 3,500 3500 3,500 3500
9.00 4P 630A ATS (Manual) Set 2 2 2,000 4000 2,000 4000
10.00 630A 4P MCCB TYPE ISOLATOR WITH ENCLOSURE BOX Set 2 2 3,500 7000 3,500 7000
11.00 7F Floor RP Panel Wing A-C1 Set 1 1 4,500 4500 4,500 4500
12.00 7F Floor RP Panel Wing B-C1 Set 1 1 4,500 4500 4,500 4500
13.00 7F Floor RP Panel Wing A-C2 Set 1 1 4,500 4500 4,500 4500
14.00 7F Floor RP Panel Wing B-C2 Set 1 1 4,500 4500 4,500 4500
15.00 8F Floor RP Panel Wing A-C1 Set 1 1 4,500 4500 4,500 4500
16.00 8F Floor RP Panel Wing B-C1 Set 1 1 4,500 4500 4,500 4500
17.00 8F Floor RP Panel Wing A-C2 Set 1 1 4,500 4500 4,500 4500
18.00 8F Floor RP Panel Wing B-C2 Set 1 1 4,500 4500 4,500 4500
19.00 LAB UPS OUTPUT PANEL-1 Set 1 1 7,500 7500 7,500 7500
20.00 7F ENGINEERING W/s PANEL-1 C1
Set 1 1 4,500 4500 4,500 4500
21.00 7F ENGINEERING W/s PANEL-2 C1
Set 1 1 4,500 4500 4,500 4500
22.00 7F ENGINEERING W/s PANEL-3 C1
Set 1 1 4,500 4500 4,500 4500
23.00 7F ENGINEERING W/s PANEL-4 C1
Set 1 1 4,500 4500 4,500 4500
24.00 7F ENGINEERING W/s PANEL-5 C2 Set 1 1 4,500 4500 4,500 4500
25.00 7F ENGINEERING W/s PANEL-6 C2 Set 1 4,500 4500 4,500
26.00 7F ENGINEERING W/s PANEL-7 C2 Set 2 4,500 9000 4,500
NT 7F ELECTRONICS LAB-1 Set 1 12,000 12000
NT 7F ELECTRONICS LAB-2 Set 1 12,000 12000
26.00 8F ENGINEERING W/s MAIN PANEL-1 Set 1 1 4,500 4500 4,500 4500
27.00 8F ENGINEERING W/s PANEL-1 C1 Set 1 1 4,500 4500 4,500 4500
28.00 8F ENGINEERING W/s PANEL-2 C1 Set 1 1 4,500 4500 4,500 4500
29.00 8F ENGINEERING W/s PANEL-3 C1 Set 1 1 4,500 4500 4,500 4500
30.00 8F ENGINEERING W/s PANEL-4 C1 Set 1 1 4,500 4500 4,500 4500
31.00 8F ENGINEERING W/s PANEL-5 C2 Set 1 1 4,500 4500 4,500 4500
32.00 8F ENGINEERING W/s PANEL-6 C2 Set 1 1 4,500 4500 4,500 4500
33.00 8F ENGINEERING W/s PANEL-7 C2 Set 2 4,500 9000 4,500
NT 8F ELECTRONICS LAB-1 Set 1 15,000 15000
NT 8F ELECTRONICS LAB-2 Set 1 15,000 15000
33.00 MAIN ELDB PANEL Set 1 1 4,500 4500 4,500 4500
N TAP-OFF BOX
S. No. Description Unit Total Qty GFC QTY Rate Amount Remarks Rate Amount Remarks
(Actual)
A LT CABLES
-
1.01 1C x 300 Sqmm Cu unArmoured Cable no. 1660 1,660
1.02 1C x 240 Sqmm Cu unArmoured Cable no. 48 86 680 32640 680 58480
1.03 1C x 185 Sqmm Cu unArmoured Cable no. 104 104 510 53040 510 53040
1.04 1C x 150 Sqmm Cu unArmoured Cable no. 20 380 7600 380
1.05 1C x 120 Sqmm Cu unArmoured Cable no. 112 962 962 107724
1.06 1C x 95 Sqmm Cu unArmoured Cable no. 10 18 402 4020 402 7236
1.07 1C x 70 Sqmm Cu unArmoured Cable no. 20 584 584 11687
1.08 1C x 50 Sqmm Cu unArmoured Cable no. 190 170 220 41800 220 37400
1.09 1C x 35 Sqmm Cu unArmoured Cable no. 10 251 2510 251
1.1 1C x 25 Sqmm Cu unArmoured Cable no. 10 233 2330 233
1.11 1C x 16 Sqmm Cu unArmoured Cable no. 10 18 202 2020 202 3636
1.12 1C x 10 Sqmm Cu unArmoured Cable no. 127 127
1.13 1C x 6 Sqmm Cu unArmoured Cable no. 110 110
-
C EARTHING -
-
1 Earthing Station -
4.01 300mm long, (40x6)mm Copper Earth bus no. 2 2 966.4 1933 966 1933
4.02 300mm long, (25x6)mm Copper Earth bus no. 756.0 756
4.03 300mm long, (25x3)mm GI Earth bus no. 1 1 348.4 348 348 348
4.04 300mm long, (25x3)mm Copper Earth bus no. 675.0 675
-
5 Earthing Cables -
-
4.1 1Cx300 Sqmm Cu unArmoured Cable- Yellow- Green
color m 1050 3,262.1 3,262 3425199
4.11
1Cx300 Sqmm Cu unArmoured Cable end termination
no. 18 1,659.9 1,660 29879
- -
4.1 1Cx240 Sqmm Cu unArmoured Cable- Yellow- Green
color m 1050 2,830.6 2972156 2,831
4.11
1Cx240 Sqmm Cu unArmoured Cable end termination
no. 18 680.0 12240 680
- -
4.1 1Cx70 Sqmm Cu unArmoured Cable- Yellow- Green
color m 160 160 883.0 141280 883 141280
4.11 1Cx70 Sqmm Cu unArmoured Cable end termination no. 16 16 390.0 6240 390 6240
- -
5.1 1Cx50 Sqmm Cu unArmoured Cable- Yellow- Green
color m 654.0 654
5.11 1Cx50 Sqmm Cu unArmoured Cable end termination no. 454.2 454
- -
6.1 1Cx16 Sqmm Cu unArmoured Cable- Yellow- Green
color m 40 40 233.1 9325 233 9325
6.11 1Cx16 Sqmm Cu unArmoured Cable end termination no. 4 4 202.0 808 202 808
- -
7.1 1Cx10 Sqmm Cu unArmoured Cable- Yellow- Green
color m 158.6 159
7.11 1Cx10 Sqmm Cu unArmoured Cable end termination no. 127.0 127
- -
8.1 1Cx6 Sqmm Cu unArmoured Cable- Yellow- Green
color m 74.3 74
8.11 1Cx6 Sqmm Cu unArmoured Cable end termination no. 96.6 97
14992175 14758098
HVAC-ELECTRICAL ALLIED WORKS
OmSai OmSai
LOI GFC QTY
GFC QTY
S. No. Description Unit Total Qty (Actual) Rate Amount Remarks Rate Amount Remarks
A POWER RECEPTICALS
Supply, Installation, Testing & Commissioning of the following components
of approved make like type of switches, socket etc,.housed in GI enclosure,
duly wired.
- -
1.00 3 Core - 2.5 Sqmm flexible FRLS copper conductor cables in already laid
conduit / raceway.(For Rawpower/ UPS) (Colour for cable Black for Raw
power & White for UPS)
m 4950 4950 95 470,250.0 95 470,250.0
- -
C LT CABLES - -
Supply, Laying, Testing & Commisioning of following sizes of 1.1 kV grade,
Aluminium/ Copper conductor XLPE/ PVC insulated Armoured/ Unarmoured
PVC sheathed LT power/control cables placed at different locations and
different lengths in cable trays, complete with all necessary consumables,
fixing clamps, identification tags etc.
- -
- -
1 Copper Conductor Cables- YFY - -
1.01 4CX16sqmm Cu Armoured Cable m 172 172 774 133,162.4 774 133,162.4
1.02 4CX10sqmm Cu Armoured Cable m 1150 1150 519 596,850.0 519 596,850.0
1.03 4CX6sqmm Cu Armoured Cable m 230 230 352 80,960.0 352 80,960.0
1.04 4CX4sqmm Cu Armoured Cable m 92 92 330 30,360.0 330 30,360.0
1.05 3CX6sqmm Cu Armoured Cable m 370 - 370 -
1.06 3CX4sqmm Cu Armoured Cable m 524 524 186 97,621.2 186 97,621.2
- -
2 Copper Conductor Cables- YY - -
2.01 4CX10sqmm Cu UnArmoured Cable m 503 - 503 -
2.02 4CX6sqmm Cu UnArmoured Cable m 329 - 329 -
2.03 3CX4sqmm Cu UnArmoured Cable m 187 - 187 -
- -
D CABLE TERMINATION - -
Supply & Installation of 1.1kV grade type Cables termination using
Single/double compression PG cable glands with earth tags, crimping type
tinned copper lugs, earthing clamps consumables for the following size of
cables.
- -
(Note:- 120Sqmm & above Size cable should have double compression cable
glands )
- -
- -
1 Copper Conductor Cables- YFY - -
1.01 4CX16sqmm Cu Armoured Cable no. 4 4 580 2,320.0 580 2,320.0
1.02 4CX10sqmm Cu Armoured Cable no. 50 50 280 14,000.0 280 14,000.0
1.03 4CX6sqmm Cu Armoured Cable no. 288 - 288 -
1.04 4CX4sqmm Cu Armoured Cable no. 10 10 215 2,150.0 215 2,150.0
1.05 3CX6sqmm Cu Armoured Cable no. 259 - 259 -
1.06 3CX4sqmm Cu Armoured Cable no. 12 12 280 3,360.0 280 3,360.0
- -
2 Copper Conductor Cables- YY - -
2.01 4CX10sqmm Cu UnArmoured Cable no. 302 - 302 -
2.02 4CX6sqmm Cu UnArmoured Cable no. 288 - 288 -
2.03 3CX4sqmm Cu UnArmoured Cable no. 219 - 219 -
- -
E CABLE TRAYS - -
Supply and installing of following size of fabricated HOT
Dipgalvanised 2mm thick cable tray made of suitable type of angles /
sheets, including horizontal and vertical bends, reducers, tees, cross
members and other accessories as required and suspended from the
ceiling.
- -
Note: The rate shall include all necessary supporting structure / supports as
required at distance of 1500mm.
- -
150 x 50mm cable tray shall be with 6mm threaded rod.
300 x 50mm cable tray shall be with 8 mm threaded rod.
300 x 70mm to 450 x 70mm cable tray shall be with 12mm threaded rod.
450 x 70mm to 750 x 70mm cable tray shall be with 75 x 75mm MS angle
- -
- -
1 Ladder type cable tray - -
1.01 (150x50)mm wide Cable Tray m 872 - 872 -
1.02 (300x50)mm wide Cable Tray m 30 30 1030 30,900.0 1030 30,900.0
S. No. DESCRIPTION MAKES & MODEL Unit R1 - QTY GFC - QTY Rate AMOUNT REMARKS Rate AMOUNT REMARKS
General Note:-
a Storing, safe guarding of the supplied material shall be the scope of the vendor till
handing over.
b Availibality of material & timelines shall be discussed & agreed at the time of pre-bid
meeting, Architect's shall not be liable for any deviation from there on.
c Quoted rate shall include all charges towards transportation, loading, unloading,
lifting,installation and rectification of defects or replacement of defective material.
1.07 Supply,Installation, Testing and Commssioining of 64 Access Readers upgrade for all RUP RO 0 0
PRO systems
1.08 Supply, installation, testing and commissioning of Lenel LNL-1200 Output Control LNL-1200-S3 NO 0 0
Module.
1.09 Supply, installation, testing and commissioning of HID Dual IClass/Prox clamshell, HID NO 0 0
16K/16 applications
Supply, installation, testing and commissioning of customized Junction Box including
Enclosure to accomonadate 10 nos of 1 interface module + 1 no of Controller with
power supply module to handle Controllers / reader interface Modules / Input / Output
1.10 Modules and Locks LenelS2 CE Listed Power Supply – 12VDC output (switch LSP / Lenel NO 0 0
selectable), 220/230 VAC (1.6 amps) input, continuous supply current with enclosure
(24” x 18”x 4.5”), lock and open frame transformer, tamper switch, power distribution
module, UPS capable (Battery Optional) CE Approved (can house six standard sized
boards, 6"x8")
1.11 Supply, installation, testing and commissioning of 12V DC 7 AH Battery Exide NO 0 0
Supply, Installation, Testing and Commssioining of INTEL XEON Quad Core processor
SILVER 4108 (8C/16T, 3.5 Hz Frequency, 11MB CACHE or Better) Vcpu16 in case of
VM
2. 32 GB - RDIMM - 2666MHz [2x16GB RDIMMS]
3. 1GPBS Fast ethernet port
1.12 4. Hard Disk (SAS / SSD – C -Drive 200 GB, D-Drive- 500 GB Miminium) Dell / HP RO 0 0
5. Monitor, Keyboard, Mouse as required
6. DVD+/-RW Drive.
7. Optional - H740 Integrated RAID Controller - 1GB Cache; iDRAC9 Enterprise;
Broadcom 5720 QP 1Gb Network Daughter card PowerVault RD1000 along Windows
10 OS and SQL DB compatabile as per Lenel system
Supply, Installation, Testing and Commssioining of Processor: Min. i7 processor
2. RAM: 16GB
1.13 3. HDD: 500GB with minimum Drive Dell / HP RO 0 0
4. 1Gbps Ethernet Port
5. Keyboard, Mouse & 21’’ LED Monitor
0 0
2.00 READERS AND SWITCHES 0 0
Supply, installation, testing and commissioning of Multi-Technology Mullion Reader:
2.01 Designed to be mounted to a door mullion; Black ; Wiegand interface;75 bit PIV [will 0 0
also read cards encoded through OnGuard; Secure Mifare] HID - RP10/Sign0 20 NO
Supply, installation, testing and commissioning of Multi-Technology Mullion TYPE Bio
2.02 metric Reader: Designed to be mounted to a door mullion; Black ; Wiegand interface;75 0 0
bit PIV [will also read cards encoded through OnGuard; Secure Mifare] HID - RPK40 R1
2.03 Supply, installation, testing and commissioning of 600 LBS Ul listed Single Door EM Locks 0 0
Bel / Equivalent NO
2.04 Supply, installation, testing and commissioning of 1200 LBS Ul listed Double door EM 0 0
Locks Bel / Equivalent NO
2.05 Supply, installation, testing and commissioning of GE Interlogix 1078C Series Steel Door 0 0
contacts, Recessed steel door magnetic contacts with wire leads 3/4 in. dia. GE -1078-M NO
2.06 Supply, installation, testing and commissioning of Duress button GE - 3040-W NO 0 0
Supply, installation, testing and commissioning of Push bar , Door contacts, Hooter Dafikas/Stanley/
2.07 0 0
wuth power supply Dorma NO
Supply, installation, testing and commissioning of Eagle KF105 Break Glass White Dual
2.08 0 0
Pole without Flip Cover. Eagle - KF105 NO
0 0
0 0
3.00 CABLES, CONDUITS AND CABLE TRAYS 0 0
Supply, installation, testing and commissioning of multicore 2C, 22 SWG, 300 V, 2A,
3.01 Aluminium/PET Foil,Screened,Grey flame retardant non-corrosive jacket, 30 swg of 0 0
strands, Beldfoil shield tape with drain wire UNIFINE
/VARSHA/POLYCAB MTRS
Supply, installation, testing and commissioning of multicore 4C, 22 SWG, 300 V, 2A,
3.02 Aluminium/PET Foil,Screened,Grey flame retardant non-corrosive jacket, 30 swg of 0 0
strands, Beldfoil shield tape with drain wire UNIFINE
/VARSHA/POLYCAB MTRS
Supply, installation, testing and commissioning of multicore 8C, 22 SWG, 300 V, 2A,
3.03 Aluminium/PET Foil,Screened,Grey flame retardant non-corrosive jacket, 30 swg of 0 0
strands, Beldfoil shield tape with drain wire UNIFINE
/VARSHA/POLYCAB MTRS
3.04 Supply, installation, testing and commissioning of PVC FRLS 2MM thick, Green colour 3800 3350 254600 224450
and 25MM dia conduit VIP/Pricision MTRS 67 67
Supply, installation, testing and commissioning of MS Raceway : 1.6 x 100 x 100mm
3.05 255 75 211650 62250
Powder Coated Raceway with Cove Reputed MTRS 830 830
3.06 Supply, installation, testing and commissioning of MS Raceway : 1.6 x 200 x 200mm 220 265 281600 339200
Powder Coated Raceway with Cove Reputed MTRS 1280 1280
0
Total 747850 625900
BOQ-CCTV WORKS
OmSai OmSai
LOI GFC Amt
S. No. DESCRIPTION Makes & Models Unit TOTAL - Qty GFC QTY Rate AMOUNT REMARKS Rate AMOUNT REMARKS
General Note:-
a Storing, safe guarding of the supplied material shall be the scope
of the vendor till handing over.
b Availibality of material & timelines shall be discussed & agreed
at the time of pre-bid meeting, Architect's shall not be liable for
any deviation from there on.
c Quoted rate shall include all charges towards transportation,
loading, unloading, lifting,installation and rectification of defects
or replacement of defective material.
1 CAMERA
Supply , Installation testing and commissioning of 2 MP, IP66, IR,
2.8mm fixed,IP fixed dome camera with H.264 compression,IR
1.01 Interlogix No 76 0 0
True D/N functionality and infrared illuminators, technology
with dual-streaming capability,
1.09 Supply, installation, testing and commissioning CCTV with dual HP/Dell RO 0 0 0
graphic card Note
0 0
2 CABLES AND CONDUITS 0 0
2.01 Supply, installation, testing and commissioning of 23 AWG,CAT Tyco/ AMP MTR 3550 0 0
6, Data cable
2.02 Supply, installation, testing and commissioning of Amp Cat6 2 AMP No 3550 0 67 0
mtr patch cord Blue
2.03 Supply, installation, testing and commissioning of 100mm x Profab/ Classic MTR 71 680 48280 680 0
40mm,1.6 mm Thick GI raceways try with 2mm thick cover.
Supply, installation, testing and commissioning of IO module
2.04 Tyco/ AMP 142 1186.78 168522.76 1186.78 0
plate with RJ 45 connector with back box
Total 216802.76 0
Sl No Description Image Units Total Qty GFC QTY RATE AMOUNT Remarks RATE AMOUNT Remarks
(Actual QTY)
General Notes
no. 29 29
no.
no.
no. 701
m 200 200
2.02 40W 8 feet direct type suspended LED light fixture no. 526 526
2.03 40W 6 feet direct type suspended LED light fixture no. 229 229
2.04 20-30W 4 feet direct type suspended LED light fixture no. 31 31
2.05 14-20W 2 feet direct type suspended LED light fixture no. 135 135
2.07 15W LED recess mounted round/square downlighter no. 952 937
2.08 14-18W LED suspended mounted cylinder type no. 1439 537
downlighter ( 200mm height)
2.09 14.4W LED strip light with required driver with al m 415 415
casing and acrylic diffuser
TOTAL 0 0
DESIGNER LIGHTING
OmSai OmSai
LOI GFC QTY
GFC QTY
Sl No Description Image Units Total Qty RATE AMOUNT REMARKS RATE
(Actual)
General Notes
Pendant Light
3 Dia-300mm & 450mm height Nos 2 2
Wattage-35W LED
Area/ Room: 7F SOCIAL HUB
Chandelier
Dimension-150/300/450mm dia
4 Set 1 1
Wattage-40W LED
Area/ Room: 7F SOCIAL HUB
Transparent Military Light
(5 lights in one set)
5 Dia-300mm Set 1 1
Wattage-35W LED
Linear
Area/ Profile
Room: Lights-Suspended
7F SOCIAL HUB
Dimesion-50mm wide
6 Wattage-15W LED Mtrs 70 70
Area/ Room: Cafeteria
Chandelier
Dimension-250 dia each
8 Wattage-35W LED Nos 1 1
Area/ Room: Cafeteria
TOTAL 0
OmSai
GFC QTY
AMOUNT REMARKS
0
BILL OF QUANTITIES FOR UPS
OmSai
LOI
Sl. No DESCRIPTION UNIT QTY GFC QTY Rate AMOUNT
1 UPS
1.01 LAB UPS & Engineering w/s UPS:
Supply, Installation, Testing and Commissioning of 400kVA KWFrame Modular
Type UPS Sutiable for 50kVA power
modules, UPS shall cater 350kVA with 7+1nos(N+1) in parallel operation & 300kVA
with 6+1nos(N+1) in paralell operation. The UPS shall be with isolation transformer.
Each power modules shall be hot swapable, 3phase I/P and 3phase O/P, On-line
UPS system with IGBT based with Hormonic filters, pf: >0.99 & THDi < 3%.
The rate shall include all necessary interconnecting cables, bypass breaker, SNMP
& Backnet over IP for BMS intergatation and EPO. Sets. 2 2
(Base frame & required chequred plate to withstand load of 1000kg/sqm).
False Floor height - 600mm is available.
NT
250KVA Copper Isolation transformer rating equal to 250Kva Frame rating of the
UPS with soft starter and change over switch Each frame need a dedicated Sets. 1
Isolation transformer.
NT 150KVA Copper Isolation transformer rating equal to Frame 150Kva rating of the
UPS with soft starter and change over switch Each frame needs a dedicated Sets. 1
Isolation transformer.
1.04 Supply, Installation, Testing and Commissioning of 1 nos 20 kVA conventional UPS
without Isolation transformer , 3phase I/P and 3phase O/P, On-line UPS system
with IGBT based with Hormonic filters - For Emergency lighting .
The rate shall include all necessary interconnecting cables, bypass breaker. Cost
should include Backnet over IP for BMS intergatation. Sets. 1 1
(Base frame require to take load of 1000kg/sqm).
Available false floor height - 600mm is available.
2.02 MS racks for housing batteries suitable for SI No. 2.01, battery bank, including
battery circuit breaker & enclosure.
(Existing floor loading capacity is 1000kg/sqm. Hence vendor to consider the MS
base frame & chequred plate accross the battery room to limit the floor loading Sets. 2 2
capacity with in 1000kG/sqm.)
Available False floor height is 600mm.
2.03 Supply, Installation, Testing and commissioning of required Ah SMF Battery bank of
approved make suitable for UPS described under 1.02, to feed 200kVA load with
minimum 15 minutes backup including all necessary breakers and accessories.
The battery bank should have on board display to monitor the Capacity and
remaining running time, alarm etc.
The Li-ion Batteries should be highly safe, reliable and compliant with international
standard regulations.
Battery bank string detail to be specified.
Sets. 1 1
Vendor to consider 15 to 20 mtrs of cable length from UPS to Battery. The type of
Cable shall be Uni-nyvin.
(Base frame required considering the floor loading of 1000kg/sqmt).
Available False floor height is 600mm.
2.04 MS racks for housing batteries suitable for SI No. 2.03, battery bank, including
battery circuit breaker & enclosure.
(Existing floor loading capacity is 1000kg/sqm. Hence vendor to consider the MS
base frame & chequred plate accross the battery room to limit the floor loading Sets. 1 1
capacity with in 1000kG/sqm.)
Available False floor height is 600mm.
2.05 Supply, Installation, Testing and commissioning of required Ah SMF Battery bank of
approved make suitable for UPS described under 1.03, to feed 100kVA load with
minimum 15 minutes backup including all necessary breakers and accessories.
The battery bank should have on board display to monitor the Capacity and
remaining running time, alarm etc.
The Li-ion Batteries should be highly safe, reliable and compliant with international
standard regulations.
Battery bank string detail to be specified.
Vendor to consider 15 to 20 mtrs of cable length from UPS to Battery. The type of Sets. 1 1
Cable shall be Uni-nyvin.
(Base frame required considering the floor loading of 1000kg/sqmt).
Available False floor height is 600mm.
2.06 MS racks for housing batteries suitable for SI No. 2.05,battery bank, including
battery circuit breaker & enclosure.
(Existing floor loading capacity is 1000kg/sqm. Hence vendor to consider the MS
base frame & chequred plate accross the battery room to limit the floor loading Sets. 1 1
capacity with in 1000kG/sqm.)
Available False floor height is 600mm.
2.08 MS racks for housing batteries suitable for SI No. 2.07,battery bank , including
battery circuit breaker & enclosure.
(Existing floor loading capacity is 1000kg/sqm. Hence vendor to consider the MS
base frame & chequred plate accross the battery room to limit the floor loading Sets. 1 1
capacity with in 1000kG/sqm.)
Available False floor height is 600mm.
Total
1 AMC CHARGES
Comprehensive AMC charges for maintaining above said kVA UPS system for 3
Years including Batteries after Warranty period. (with 100% faulty spares /
components replacement)
4th year
5th year
6th year
Note:
Vendor shall arrange UPS factory test inspection for client / consultanats /PMC
before dispatching UPS from UPS systems.
BOQ: DX PAC UNIT
OmSai
LOI
Sr. No. Particulars Unit Total Qty GFC QTY Rate AMOUNT REMARKS
-
1.00 PAC UNITS WITHOUT HEATER & HUMIDIFIER -
Supply Installation, testing and commissioning of following rating of DX
type Precision Packaged unit of top discharge and front suction type
(without Heater and Humidifier) Comprising of following items.
Refrigerant shall be LOI10 A. Unit cost shall be inclusive of Lifting
shifting and positioning of PAC indoor and outdoor unit to desired floor
as per approved shop drawing. The out door unit shall consist of the
multirow condenser coil, propeller fan with IP54 motor and electrical
isolator for servicing. The indoor unit shall comprise the invertor type
Compressers, cooling coil, filters to achieve 5micron filteration level,
Thermostatic Expansion valve, liquid line strainer, refrigerant drier etc.
The blower shall be with EC fans and shall be provided with fan guard.
Water leak detector, Microprocessor control shall also be included. All
these components shall be suitably interconnected in a powder coated
sheet metal cabinet of strong construction. The unit shall be of double
skin construction on all Four Sides with Class O Fire rated Insulation.
PAC shall be compatible for third party BMS integration with BACnet
with open protocol. The quoted price to include the following. Machine -
mounted microprocessor with digital display panel, Auto restart in the
event of power disruption, Moisture sensor below the false floor,
Sequence controller, 1 sets of Potential free contacts for all drives etc.
Actual Capacity at design conditions. Inside Condition DBT/RH : 22 Deg
C +/- 1 Deg C & RH 50%. +/- 5%. Outside Condition DBT :45 deg C.
Note: Quoted price shall be inclusive of Refrigerant charge (LOI10A) for
both IDU and ODU. The compressor MCB trip alarm generation
provision should be available in the BMS communication
The PAC units should be covered with 3 years standard warranty and
necessary cost for the same should be considered. The PAC warranty
should be comprehensive type & cost for scheduled visits, preventive
maintatenance should be included in the unit cost
0
7.00 Supply & Installation of GSS motorized On/off Damper (18 G GSS)
complete with all standard accessories in accordance with the approved
shop drawings and technical specifications. Size of the damper shall be Nos 4 4
suitable to PAC unit return air opening.
0
8.00 Supply & Installation of Non spring return actuators, control panel, and
all accessories in accordance with the approved shop drawings and Nos 4 4
technical specifications.
0
9.00 Supply & installation of adjustable type MS stand for Indoor units &
Set 4 4
Static type for out door unit with Anti-corrosive paint and vibration
isolators. 0
10.00 Supply, installation, testing & commissioning of Extended piping kit to
include NRV and Solenoid valves with control wirirng. Set 4 4
0
11.00 Supply of Refrigerant gas (Measurment to be provided during
commissioning) Kg 210 4
0
12.00 Supply & installation of height adjustable type MS stand for Indoor units
with Anti-corrosive paint and vibration isolators. For outdoor unit refer Set 6 4
Tender drawing sectional detail.
0
13.00 CPVC Pipes with 6mm thick Closed Cell Polyethylene 0
Supply, installation testing and Commissioning of Drain Piping for indoor
units. CPVC piping complete with fittings, supports as per specifications 0
and insulated with 6 mm thick closed cell polyethylene.
13.01 40 mm dia. Rmt 60 60
13.02 32 mm dia. Rmt 40 40
13.03 25 mm dia. Rmt 0
0
14.00 Supply, installation testing and Commissioning of Condensate Drain
pump (2 Pumps 1 Working + 1 Standby) kit complete with Insulated SS
Tank with cover for indoor units. Net holding capacity must be minimum
of 5 liters capacity & minumum head should be 6 meters from the floor
Set 2 2
level. Size shall be as per OEM recommendation. Additional overflow
tank should also be considered in the costing for these pumps with
atleast twice capacity as that of default capacity
0
15.00 CPVC Piping 0
Supply, installation, testing and commissioning of CPVC piping for fresh
water to Humidifier in PAC indoor unit in accordance with the approved 0
shop drawings and technical specifications .
15.01 40 mm dia. Rmt 50 50
15.02 32 mm dia. Rmt 20 40
15.03 25 mm dia. Rmt 0
0
16.00 Ball Valve with screwed end 0
Supply & Installation of Ball valve with screwed ends. For details refer
spec. & Pressure Rating PN 16) 0
16.01 40 mm dia. Nos. 1 1
16.02 32 mm dia. Nos. 2 2
16.03 25 mm dia. Nos. 0
0
17.00 Supply, installation, testing and balancing of powder coated Extruded
Aluminium Antistatic Supply Air Floor grilles with opposed blade damper
in accordance with the approved shop drawings and technical Nos. 29 29
specifications to fit in the floor tile size of 600 x 600 mm.
0
18.00 Supply and installation of powder coated Extruded Aluminium Return air
egg crate grilles in accordance with the approved shop drawings and Nos. 29 29
technical specifications to fit in the ceiling tile size of 600 x 600 mm.
0
19.00 Supply and Installation of 19 mm thick Class 'O' Elastomeric Nitrile
rubber insulation with factory laminated Aluminium foil and all
accessories like adhesive, tape etc.Measurement shall be considered as Sqmt 240 320
floor as well as side wall upto false flooring.
0
20.00 GI C Type Tray 0
Supply and Laying of GI C type 1.6 mm thick perforated cable tray with
all fixing accessoroes for copper pipe covering to protect the physical 0
damages. Quantities are considered inside the shaft as well.
20.01 150 mm Width - 100 mm height without GI cover Rmt 0
20.02 450 mm Width - 100 mm height with GI cover in shaft & terrace Rmt 0
20.03 300 mm Width - 100 mm height without GI cover Rmt 200 200
0
21.00 Third party Testing and Commissionin of Complete system and
necessary reports shall be submitted to Consultant / Client Lot 2 2
0
22.00 Charges towards Factory acceptance test (FAT) for 3 people
(consultant, PM, client) for all units inclusive of flight charges, Lot 0
accommodation & local travel.
0
23.00 Charges towards Site acceptance test (SAT) for all units by creating
artificial load scenario by equivalent loads as per the design.
Site acceptance test should be done via creating an artificial heat load
in the server room / UPS room by external heater banks of equivalent
Lot 0
capacity to that of proposed heat load. This is carried out for a minimum
period of 24 hours to understand the behaviour of the PAC units in a real
operational scenario.
24.00 Supply of Pre commissioning filters with equivalent filtration rating and
one set of additional filters till hand over of the units Set 4 4
TOTAL 0
OmSai
LOI
SI NO DESCRIPTION UNIT QTY GFC QTY REMARKS Rate Amount REMARKS
LIGHT MGMT SYSTEM
Supply, Installation, Testing and Commissioning of following Lighting
1 Sensors with necessary Accessories Complete
SITC of Wireless Daylight Sensor for rooms which works on 865 MHz,
ceiling mount, battery-powered, 44 mm (1.6 in) diameter similar to 36 36
8 LRF5-DCRB-WH nos
VAV Boxes shall also be able to reset any air flow between zero
and the maximum air quantity that the boxes can handle without
changing orifices or other parts, but the boxes shall be factory set
at 20% of the maximum flow as minimum flow. The noise level
from the VAV boxes shall not exceed 35dbA. The quoted price
shall be inclusive of the Digital type thermostat with display of
occupied one temperature for each VAV unit & associated cable in
FRLS PVC Conduit required for the functioning of the VAV system.
4.00 The TEC series VAV thermostat for Variable Air Volume (VAV) With
Display equipment with or without local reheat, and other zoning
equipment utilizing damper actuators with on/off, floating, or NOS 292 284
proportional 0-10 VDC control inputs
5.02 Supply, Laying, Termination of ISI Certified 3 Core 1.0 sq.mm ATSC,
FRLS ,PVC insulated, Unarmored, Tinned Copper, twisted, shielded,
PE insulated, Power cabling with proper ferrules, lugs and other
necessary accessories. The spec shall meet the system Rmt 2774 3152
manufacturer spec
5.03 Supply, Laying, Termination of ISI Certified 4 Core 1.0 sq.mm ATSC,
FRLS ,PVC insulated, Unarmored, Tinned Copper, twisted, shielded,
PE insulated, Power cabling with proper ferrules, lugs and other
necessary accessories. The spec shall meet the system Rmt
manufacturer spec
5.04 ISI Certified 25mm Dia, 2mm thick, PVC Conduit with Orange
colour band in 1mtr interval bends, collar, saddles, saddle base
and other accessories for Signal Cable / DDC Communication Cable Rmt 5577 6310
Total -
BOQ FOR FIRE EXTINGUISHER
OmSai
LOI
Total 0
HVAC lowside BOQ
OmSai OmSai
LOI GFC - ACTUAL
S. No. Description Unit
Total qty GFC QTY (Actual) Rate Amount Remarks Rate Amount Remarks
A) High Side Equipments
Supply and installing of following size of fabricated galvanised 2mm thick ladder
type/ Perforated Type cable tray made of suitable type of angles / sheets,
including FACTORY MADE horizontal and vertical bends, reducers, tees, cross
members and other accessories as required and suspended from the ceiling.
Note: The rate shall include all necessary supporting structure / supports as
required.
150 x 50mm cable tray shall be with 6mm threaded rod.
300 x 50mm cable tray shall be with 8 mm threaded rod.
300 x 70mm to 450 x 70mm cable tray shall be with 12mm threaded rod.
450/600 x 70mm to 750 x 70mm cable tray shall be with 75 x 75mm MS angle
1.00
Supply & Installation of Factory fabricated, powder coated Double skin GSS
plenum with 25 +/- 2 mm thick sandwich RPUF injected panel. Outerskin shall
be 0.63mm pre plasticized or powder coated GSS sheet. Inner sheet shall be Sqm 353 425
0.63mm plain GSS with extruded Aluminum corners in accordance with the
approved shop drawings and technical specifications.
2.00
Supply & Installation of Factory fabricated Sound Attenuator of 0.8mm GSS
Outer Casing & 0.8mm GSS Perforated inner baffles filled with inorganic fibre
Sqm 182 231
glass of Class'O' Acoustic Material. Insertion loss should be approx. 18 dB to 23
dB. Min. Length should be 900 mm
4.00 GI Spiral Oval Duct (Factory Fabricated) with 9mm Thick Insulation
Supply & Installation of UL-555 Certified Fire damper complete with outer shell
with 1.6mm thick galvanized steel frame and the blade/Leaf with 16G GSS,Class-
1 Leakage, control panel,temperature Sensors,Duct type smoke detectors,
transformer to convert 240 V AC to DC Voltage, motorized electric actuator,
spring return type with complete boxing as per specification in accordance with
the approved shop drawings and technical specifications.
6.00 Supply & Installation of GSS motorized modulating Damper (18 G GSS)complete
with all standard accessories in accordance with the approved shop drawings Sqm
and technical specifications.
7.00 Supply & Installation of GSS motorized On/off Damper (18 G GSS)complete with
all standard accessories in accordance with the approved shop drawings and Sqm 3
technical specifications.
8.00 Supply & Installation of Non spring return actuators, control panel, and all
accessories in accordance with the approved shop drawings and technical No 23
specifications.
10.00 Supply & Installation of GSS Volume Control Dampers (18 G GSS)with operating
handle for Supply air duct branches in accordance with the approved shop Sqm 22 24
drawings and technical specifications.
11.00 Supply & Installation of OVAL GSS Volume Control Dampers (18 G GSS)with
operating handle for Supply air duct branches in accordance with the approved Sqm 123 129
shop drawings and technical specifications.
Supply & Installation of Powder coated Extruded Aluminium (18 G) Return air
diffuserswith removable core, in accordance with the approved shop drawings
and technical specifications to fit in the tile size of 600 x 600 mm. The neck size
shall be of following sizes
16.01 225 x 225 mm No
16.02 300 x 300 mm No 46 60
16.03 375 x 375 mm No 46
16.04 450 x 450 mm No 25 21
NT 525 x 525 mm No 5
Supply & Installation of Spill Air Plenum / Mixing boxes made of 22G G.I sheet
with necessary spigot connection for fixing flexible duct and suitable collar for
connecting to various neck diffuser / slot diffuser. The box should be internally
insulated with 6mm thick open cell nitrile rubber. And with necessary chains for
supporting and anchor fasten in accordance with the approved shop drawings
and technical specifications of following sizes.
22.00 Supply & Installation of Powder coated Extruded Aluminium (18 G) grilles
without collar damper & four side flanges for return air in accordance with the Sqm 36 51
approved shop drawings and technical specifications of following sizes.
NT Supply & Installation of Powder coated Extruded Aluminium (18 G) grilles with
collar damper & four side flanges for Supply air in accordance with the approved Sqm 12
shop drawings and technical specifications of following sizes.
23.00
Supply & Installation of Powder coated Extruded Aluminium (18 G) Continuous
Linear grilleswith necessary flanges for supply & return air, Distance between
balade shalle 12.5 mm to 15 mm and balde thickness shall be 20 G in Sqm 46 35
accordance with the approved shop drawings and technical specifications of
following sizes.
24.00 Supply & Installation of Aluminium Powder coated collar damper for
supply air in accordance with the approved shop drawings and technical Sqm 21 14
specifications.
25.00 Supply & Installation of Aluminium Powder coated double frame, Non-Vision
louverwith flange width of 30mm to be used in pantry doors. The Color of the Sqm 3.3 2.5
non vision louver shall match with that of doors.
26.00 Supply & Installation of GI Duct Access doors. It shall be ultra low leakage
design, suitable for connected duct pressure rating and externally insulated. The Sqm 4 10
operation shall be using camlock.
27.00 Installation of VAV Box with necessary Hi-tech support & Anchor Fastners in
accordance with the approved shop drawings and technical specifications. NOs 292 296
28.00 Supply & Installation of 24 G GI VAV Transition piece in accordance with the
approved shop drawings and technical specifications.
28.01 VAV Inlet - Cone Connection Nos 292 283
28.02 VAV Outlet - Rectangular Connection Nos 292 283
E) Insulation Works
1.00
Supply & Installation of Acoustic liningon the walls of AHU room wall exposed to
office space with 50 mm thick fibre glass of 48 Kg/Cum density with GI frame
grid covered with 26G perforated GI sheet & the same shall be kept 50 mm Sqm 461 425
away from the AHU room wall to act as air gap to increase the acoustic property
in accordance with the approved shop drawings and technical specifications.
2.00
Supply & Installation of Acoustic liningon GI Supply air ducts. The Acoustic
material shall be 15 mm thick open cell elastomeric foam class '1'. The density
shall be 140 kg.m3 with thermal conductivity of 0.05 W/ m Deg K.Material shall
have anti-bacterial properties The insulation shall be as per technical Sqm 971 750
specification and drawings etc, All joints to be sealed with anti condensation
tapes. All loose ends to be trated with nosing frames as per details provided in
Typical connection details drawing
3.00
Supply and installation Under deck insulation with FM approved Class 'O' Closed
Cell antimicrobial Elastomeric Nitrile Rubberwith density of 40 - 55 kg/cum as
per the thickness mentioned below, with fire retardant adhesive and joints
sealed with 3mm thick, 50mm wide nitrile rubber self adhesive tape in
accordance with the approved shop drawings and technical specifications.
Quoted price shall be inclusive of adhesive, tapes, etc.
4.00
Supply & Installation of External Thermal insulationon Supply air ducts with
Class 'O' Elastomeric nitrile rubber Thermal Closed Cell in accordance with the
approved shop drawings and technical specifications. Quoted price shall be
inclusive of adhesive, tapes, etc.
4.01 9 mm thick Sqm 1803 1400
4.02 13 mm thick Sqm
5.00
Supply & Installation of 26G G.I duct type Cross Talk
Attenuator(FACTORY FABRICATED) The Acoustic material shall be 15
mm thick open cell elastomeric Nitrile rubber insulation class '1'. The
density shall be 140 kg.m3 with thermal conductivity of 0.05 W/ m Deg
K.Material shall have anti-bacterial properties & grills in the open ceiling
area that insulation shall be as per technical specification and drawings
etc
5.01 (200x200)mm No
5.02 (250x250)mm No 72 50
5.03 (300x300)mm No 24 97
5.04 (450x300)mm No
6.00 Minor civil works (Icluding Gyp)such as making any small openings /
closing the same for refrigerant pipes / chilled water pipes / ducts / Lot 3 3
dampers etc.
8.00
Supply & Installation of Powder coated Extruded Aluminium (18 G) Curved
Linear / patch grilles with necessary flanges for supply air with multi blade collar
damper, Distance between balade shalle 12.5 mm to 15 mm and balde Sqm 50 40
thickness shall be 20 G in accordance with the approved shop drawings and
technical specifications of following sizes.
9.00 Executing & witnessing of electronic air balancing of AHU's for the project.
Quote should be inclusive of the electronic devices namely aenemometers etc
and personnel. Pre occupancy & post occupancy air balacing to be considered
for quote per AHU.
Note: All necessary and additional sockets as required in the chilled water piping
system for BMS / Automatic operation need to be provided at no extra cost.
Bidders are advised to visit site before quoting and understand the complete
work involvement.
All the paints used shall have VOC level below 250 g/ltrs. VOC level for any
sealants shall be less than 250 g/ltrs and for rubber lining including Nitrile
Rubber Insulation shall be less than 850g/ltrs.
Total
BOQ FOR VRF WORKS
OmSai OmSai
LOI GFC Amount
S. No. Description Unit Total Qty GFC Qty - DX GFC Qty - DX GFC Qty Amount Remarks Amount Remarks
Critical Room NonCritical Rate Rate
Room
A) VRF Units
Set
11.00 DX Units
Supply and Installation, testing and commissioning Hi-
Wall Split Ac units. Each Indoor unit shall be complete
with cooling coil, Fan. Filter, controls and accessories.
The outdoor unit shall be complete with Inverter
compressor, condenser fans and other accessories. The
unit shall be charged with R-410A refrigerant. The noise
level shall not be more than 40 dB(A)at normal
operation measured horizontally 1m away and 1.5m
above ground. The capacities of each machine and
quantities are as indicated below. The quoted price shall
be inclusive of cordless remote control, wiring, electrical
cable with plug from isolator provided by others near
outdoor / indoor unit and also hiwall with drain pumps
should also be included with Power cabling from
stabilizers to ODU. 5 STAR
1.1TR RO
1.3 TR RO
NT 1.6TR No 27 27
1.5TR RO
2 TR RO
Supply Installation, testing and commissioning Cassette
Ac units. Each Indoor unit shall be complete with
cooling coil, Fan. Filter, controls and accessories.
The outdoor unit shall be complete with rotary
compressor, condenser fans and other accessories. The
unit shall be charged with R-410A refrigerant. The
indoor unit noise level shall not be more than 40
dB(A)at normal operation measured horizontally 1m away
12.00 and 1.5m above ground. The capacities of each machine
and quantities are as indicated below. The quoted
price shall be inclusive of cordless remote control,
wiring, electrical cable with plug from isolator
provided by others near outdoor / indoor unit. The
quaote should be inclusive of with drain pump.
12.01 1.5 TR - RO
12.02 2.0 TR - RO
12.03 3.0 TR - RO
12.04 4.0 TR - RO
Total
BOQ FOR FIRE SPRINKLER SYSTEM
OmSai OmSai
LOI GFC - ACTUAL
GFC QTY
SL No. Description Unit Total Qty (Actual) Rate Amount REMARKS Rate Amount REMARKS
Supply and installation of standard response chrome finish quartzoid bulb Pendent type
2 sprinkler with 15mm screwed ends. Temp rating: 68 deg C; K factor: 80. Sprinklers shall be UL Nos 649 440
Listed approved.
Supply and installation of standard response chrome finish quartzoid bulb upright type sprinkler
3 with 15mm screwed ends. Temp rating: 68 deg C; K factor: 80. Sprinklers shall be UL Listed Nos 649 501
approved.
Supply and installation of Rosette plates ( Recessed type, in two piece, for false ceiling areas )
4 for Sprinklers below false ceiling area of 2 mm thick MS metal. Finish shall be powder coated Nos. 909 752
and color shall be as approved by architects / clients.
Supply, installation and testing of Stainless steel corrugated flexible pipe(hose) for dropping
5 sprinklers below false ceiling, pipe of 13.5 bar pressure rating and specified long 25 mm dia
with union / reducer collar, clamps etc. as required. (UL listed Unbraided)
Reusing of dismantled existing sprinkler fire pipes heavy class including cutting ,welding and
7 jointing with all fittings i.e. tees , bends , elbows , flanges , reducers & pipe hanger assembly
(struts, rods, brackets, straps) etc., complete as per approved respective floor drawing provided.
Disconnected / Dummy of existing pendent sprinkler bulbs with proper end cap wherever
8
required. Complete as per approved floor drawing provided.
8.01 Pendent sprinkler bulb Nos. 323 379
Removing the existing dummy point provision provided by builder for Upright piping work
9
considering cutting and welding works for the same. Nos. 649 493
Refixing of existing pendent sprinkler bulbs wherever required rigid drops or flexible hose.
10
Complete as per approved respective floor drawing provided.
10.1 pendent sprinkler bulb Nos. 506 446
Supply, Installation, Testing & Commissioning of Cast Iron Butterfly Valve (PN-16) with
11
matching flanges etc., complete. Shall be with ISI /international certification Listed.
Supplying, installing, testing and commissioning approved make Pressure gauge 15mm dia of
12 RO 0 0
4" dial with valve tee and fittings
Supply, Installation, Testing & Commissioning of Brass Ball Valve with necessary union etc.,
13
complete.
13.01 50 mm dia. Nos.
13.02 25mm dia. Nos. 9 9
Charging of sprinkler pipes with builder water provided for 2.5 times the working pressure up to
14 Nos. 9 9
18-24 hours for entire respective floor.
Total 0 0
BOQ FOR GAS SUPPRESSION SYSTEM
OmSai OmSai
LOI GFC QTY
GFC QTY
SL No. Description Unit 7th Floor (Actual) Rate Amount Remarks Rate Amount Remarks
Supply & installation of Seamless cylinder CCOE/PESO approved, complete with valve assembly
and arrangement for supervisory switch connection for monitoring cylinder pressure, a pressure
1 gauge with a safety burst disc and a safety cap complete.
Supply, installation & testing of Master cylinder Electric control head operated electrically from the
3 Detection and control system or locally with manual lever on the control head. Nos 1 2
Supply & installation of discharge Nozzle are designed to provide the proper flow rate and
4 distribution of Novec 1230 to total flood a hazard area: 180/360 deg. Nos 3 4
Supply & installation of flexible discharge hose route the gas agent from the storage cylinder to the
discharge piping by a flexible rubber hose with wire braided reinforcements. This hose is connected
5 to the discharge outlet Novec 1230 cylinder valve and terminates at the system piping or discharged Nos 1 2
manifold.
6 Supply & installation of Warning plate for use Inside/outside room Nos 1 1
Supply, installation & testing of Pressure switch for discharge pipe.(3 Pole double throw)
9 Nos 1 1
Supply, installation, testing of Piping, fittings, hose & support pipes : M.S. Seamless pipes as per
ASTM A 106, schedule 40. Pipe shall be supported from required ht of true slab including
10 necessary structural supports for cylinder mounting as per approved dwg. Pressure test to be done L/S 1 1
with nitrogen gas up to 14 Kgs/cm2.
Supply, installation, testing and commissioning of 2 Zone (loop) Conventional fire alarm panel with
11 gas release module. UL Listed Nos 1 1
Supply, installation, testing and commissioning of Conventional Manual call point. UL Listed
14 Nos 1 1
15 Supply, installation, testing and commissioning of Sounder cum strobe. UL Listed Nos 1 1
16 Supply, installation, testing and commissioning of Abort release switch. UL Listed Nos 1 1
17 Supply, installation, testing and commissioning of Manual release switch. UL Listed Nos 1 1
18 Supply and laying of 2C X 1.5 Sq.mm Armoured FRLS Cable. Mtrs 268 268
19 Room Intergrity Test report (Fan test carried out by OEM team only) L/s 1 1
Total
BOQ FOR FIRE CURTAIN
OmSai OmSai
LOI GFC Qty
Total Qty-
SL No. Description Unit 7th Floor 8th Floor Total Qty-R0 7th Floor 8th Floor Total Qty-R1 Rate Amount REMARKS Rate Amount REMARKS
GFC QTY
Supply & Installation of 120 minutes rated Fire Curtain with Galv. MS Head
Top Box (200mm x 200mm minimum dimensions), Powder Coated Side
Guides (100mm x 53mm minimum dimensions) ,Adjustment Channels and
Bottom Bars with geared motors for power up operation with Standard Battery
backup and operated system Safe fixed into Steel rollers with woven glass fiber
fabric, reinforced with stainless steel wire having micronized aluminium
polymer coating on each side of the fabric (silver/grey) with its control panel
and all installation assemblies & accessories required to complete the
installation. The operation shall be suitable for dedicated 230 Volts UPS, 50 Hz
AC supply.Complete system tested in accordance with BS EN 1634-1 (for 120
minutes Integrity & tested at 1000°C) to BS 476-22.8 and BS 7346-3 . The
Emergency Retract Switch is needed on both side of the curtain. The curtain
should reset automatically when Fire Control Panel is reset. Vendor /
Manufacturer to submit valid Test Report for the complete systems and not just
for fabric from an independent international accredited laboratory. The Test
Report of complete system should not be more than 5 years old.
Vendor/Supplier should duly submit current dated authorization letter from the
manufacturer or principal that he is representing.
1
The automatic smoke or fire curtain control panel require a UPS supply or
220v-240v (Selectable) (AC) 3 core 1.5mm thickness wire Supply in order to
keep the batteries charged up; The mains supply does not have any other
function apart from keeping the batteries charged-up, this is because the current
required for driving the system is taken from the lead-acid cells; however it is
advise that the panel should have an uninterrupted mains supply under normal
conditions, where possible to ensure correct functionality of the system. (FC-
01)
Curtains including Top box, Side Guides, Curtains, barrel including motor,
dummy end and
b bottom rail. (Mode of measurement shall be the Sq.Mtr 128 150 278 21 37 58 35.5 0 0
area of curtain covering the opening)
0 0
BOQ FOR FIRE ALAMR WORKS ( LIFE SAFETY)
OmSai Omsai
LOI GFC QTY
S. NO DESCRIPTION UNIT QTY GFC QTY Rate AMOUNT REMARKS Rate AMOUNT REMARKS
Supply, installation, testing and commissioning of 2000 watt Amplifier box with
1.02 integration of Networkable Intelligent Analogue Addressable Fire Control Panel Nos 1 1
Supply, installation, testing and commissioning of 8 Loop wall recess/surface
mounting microprocessor based Networkable Intelligent Analogue Addressable Fire
Control Panel. The panel shall be networkable and shall communicate with all the
Fire Alarm Panels in the networks. The Events, alarms and any other function which
1.03 is feasible in the local Fire Control panels shall be feasible in the Master panels for all Nos 1 1
the panels that are networked.
Supply, Installation, Testing & Commissioning ofn low profile design, 1/4, 1/2, 1 and 2
3.04 Watt, upto 100db at 1meter and 90 db at 3 meter with white housing . Ceiling Nos 425 362
mounted
Supply, Installation, Testing & Commissioning of low profile design, 1/4, 1/2, 1 and 2
3.05 Watt, upto 100db at 1meter and 90 db at 3 meter with 4" electrical standard box and Nos 282 301
white housing . True cieling mounted
Supply, Installation, Testing & Commissioning of low profile design, 1/4, 1/2, 1 and 2
3.06 Watt, upto 100db at 1meter and 90 db at 3 meter with 4" electrical standard box and Nos 16 16
white housing . Wall mounted
Supplying, installing, testing and commissioning of Emergency Telephone Stations
3.07 comprising a portable telephone handset with latch type enclosure Nos 33 33
Supplying, installing, testing and commissioning of Emergency Telephone Station jack
3.08 with SS face plate. Nos 21 21
3.09 Supplying, installing, testing and commissioning of Emergency Telephone Hand set Nos 5 5
Supply, Installation, Testing and Commssioining of 2 core twisted pair 1.5 Sqmm,
ATC, Multi strand, over all PVC sheathed with Grey color outersheath FRLS armoured
5.02 shielded cable with all mounting saddles, GI spacers, GI screws with the required Mtrs 12350 11250
junction boxes, cables glands.
Supply & Laying of ISI Certified 25 mm", 2mm thick, FRLS, PVC Conduit of RED Colour
5.03 with bends, collar, saddles, saddle base and other accessories Mtrs 370 370
Supply and Installation of 2mm thick, 50mm hieght, 300mm GI Powder coated,
5.04 perfrated type cable try with 1.6mm Thick top cover Mtrs 160 105
Supply and Installation of 2mm thick, 40mm hieght, 200mm GI Powder coated
5.05 perfrated type cable try with1.6mm Thick top cover. Mtrs 400 290
Total - -
Supply, installation, testing and commissioning of 2 Normal lane + 1 Wider
lane Sensor Swing type flap Barrier:- 1000 or 1200mm Hieght, Passage width
should be 550/650mm for normal passage, 900 mm for pedetrain passage,
The housing and the base columns are made of AISI 304 stainless steel with
BOQ FOR FLAP
semigloss and Technopolymer top, Emitter/receiver BARRIER
infrared sensors
technology, Tailgatting, Wrong way entry, Piggy bagging, leave aisle time out, OmSai
S.No intrution, Lane indicator displays,Bi-directional
Item Descriptionoperation,Flap material with Unit 7th 08th Qty Rate Amount REMARKS
10mm acrylic or Pure tefflon glass, Safety sensor prevents closing of flaps
1.00 (Flap
During emergency flaps to open automatically & Should be detect trolly ) ,
Barrier
ensuring pedestrian safety, MHTM™ drive, ADA-compliant passage for
wheelchairs,Fail-Safe manual push opening, Accurate presence sensing,
1.01 SLIM LANE-to2fix
Provisions Lane
thepassage
readerswidth 550/650
without mm 10 poles.
any separate Million MCBF, 1 lane Set 0 0 0 0
passage width 900mm 10 Million MCBF
Flap Barrier should monitors the individual passages in both directions. This
sensor
Total system also monitors the swinging area and the blocking elements and 0
acts as a protection device. In the event of a power failure, both directions
may be freely accessed. Automatic reset upon resumption of power supply –
the unit resets to its regular function without manual intervention. The access
area is secured immediately upon resumption of power supply. Unit should
have capabale to terminate the frire signal inacase of an emergency.
BOQ FOR WLD WORKS
OmSai OmSai
LOI GFC QTY
S. No. Description Unit 7TH GFC QTY Rate Amount Remarks Rate Amount Remarks
Total - -
BOQ FOR RODENT REPELLENT SYSTEM
OmSai OmSai
LOI GFC Amt
S. No. Description Unit GRD 7TH 8TH QTY GFC QTY Rate Amount REMARKS Rate Amount REMARKS
Total 0 0
BOQ FOR VESDA SYSTEM
OmSai OmSai
LOI GFC Amt
S. No. Description Unit 7TH GFC Qty Rate Amount Remarks Rate Amount
1.00 VESDA
Supply, installation, testing and commissioning of 1 zone
1.01 VESDA Laser Scanar, including 24V DC Power supply including 1 1
battery and all necessary accessories, including programing &
configuration.
Nos.
Supply, installation, testing and commissioning of FRLS PVC
1.02 Pipes, 2mm thick, 25mm dia, FRLS, for Aspiration capillary 165 165
tubes. Including end caps etc. Mtrs.
Supply, installation, testing and commissioning o Air
1.03 termination Nozzles including accessories for above units as 18 18
per design calculation. Nos.
Supply, installation, testing and commissioning o Electronic
1.04 Hooter with Strobe. 1 1
Nos.
Supply, installation, testing and commissioning of Aspiration
1.05 capillary tube including end caps for above units as per design 18 18
calculation. Nos.
Supply, installation, testing and commissioning of Armoured
1.06 cable 2C x 1.5sq.mm. for internal VESDA Panel to Monitor 15 15
Module. Nos.
Total - -
OmSai
GFC Amt
Remarks
BOM FOR BUILDING MANAGEMENT SYSTEM
OmSai
LOI
S. NO DESCRIPTION UNIT QTY GFC QTY Rate AMOUNT REMARKS
1.00 GRAPHICS, SOFTWARE AND PC
Supply, Installation and Testing of Rack mounted IBMS Server Station with
min Xeon E5 processor or greater with min 16 GB RAM with DVD drive,
H.V.G.A. Card, 4 GB Graphics card, min 1 TB Mirror HDD (or) Required
Storage for loading Data base/OS software + 2 years logs & events(which
ever is higher),1 GB Ethernet Network Interface card, Scroll Mouse & original
Software with RAID 5 The original 64 bit OS Windows Server (2008 or above)
software, Latest MS office software, Anti virus software(as per client
requirement- Antivirus software should automatically scan the computer
1.01 bios and all files opened, created, copied, and/or received for viruses. Include Nos 1 1
directions for updating virus definition files upon expiration of warranty
within the record documentation), with the required serial & parellel ports, 4
USB Ports 21” LED Colour HD Monitor. If the vendor Server requirement is
more than what is specified here, the vendor shall quote the configuration
that meets their requirement and shall indicate the configuration quoted.
Vendor shall consider the required hardware, licenses, software , not listed
here,if required, to meet all the requirements given in the Technical
Specifications
3.01 For Electrical Meters - TVM Meter, MDM, LOAD Meter Set
3.02 For UPS Set
3.02 For VAV's Set 1 1
3.03 For VFDs Set 1 1
3.03 For Fire Alarm System - All point integration Set
3.04 PAC Set 1 1
3.04 VESDA Set
3.05 WLD Set
3.05 VRF Set 1
3.06 LMS Set
Supply, installation, testing and commissioning of Duct type CO2 Sensor with
4.07 detecting range of 0- 2000ppm and power operating of 24 Volt AC/DC , output Nos 18 18
of 0-10v or 4-20mA
Supply, Installation, Testing Diffrential Pressure Transmitter (Water Pressure
4.08 Sensor) With output of 4 to 20 mA or 0-10V DC Supply and Input of 24V DC/AC Ro
Supply, Installation and Testing of Current Relay for sensing On / Off status of
4.09 Fans as per point summary Nos 36
Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm FRLS,PVC insulated,
5.01 Mtr 1100 1100
Unarmored,Cable with proper ferrules, lugs and other necessary accessories.
Supply, Laying, Termination of ISI Certified 2 Core 1.0 sq.mm ATSC,(Aluminium
Mylar with Atc Drain wire of 0.5 Sq. mm) FRLS,PVC insulated, Unarmored,
5.02 Mtr 6750 6750
Tinned Copper, twisted, shielded, PE insulated, lugs and other necessary
accessories.
Supply & Laying of ISI Certified 25 mm", 2mm thick, PVC Conduit of Orange
5.06 Colour with bends, collar, saddles, saddle base and other accessories for Signal Mtr 2340 2340
Cable / DDC Communication Cable.
Supply & Laying of ISI Certified 19 mm", 2mm thick, PVC Conduit of Orange
5.07 Colour with bends, collar, saddles, saddle base and other accessories for Signal Mtr 2150 2150
Cable / DDC Communication Cable.
Supplying, laying and fixing of heavy class GI conduits of 25mm dia complete
5.08 with all accessories. RO
5.16 Supply, Installation, Testing & Commissioning of 4-port BS style Faceplate White RO
5.17 Supply, Installation, Testing & Commissioning of 2-port BS style Faceplate White RO
Supply, Installation, Testing & Commissioning of Cat6 UTP Jack , Blue/Black, For
5.18 Jack pane RO
Supply, Installation, Testing & Commissioning of Cat6 RJ45 UTP Patch Cords, - 1
5.19 Meter, RO
Supply, Installation, Testing & Commissioning of Cat6 RJ45 UTP Patch Cords, - 7
5.20 ft, RO
GRAND TOTAL -
BOQ FOR PLUMBING WORKS FOR PANTRY
OmSai OmSai
LOI GFC BOQ Amt
Sl.No. Description Unit Grd floor 7th floor 8th floor Total Qty GFC QTY Rate Amount Rate Amount
General note :
a Storing, safe guarding of the supplied material shall be the scope of the vendor till handing over.
b Availibality of material & timelines shall be discussed & agreed at the time of pre-bid meeting, Architect's shall not be liable for any deviation from there on.
c Quoted rate shall include all charges towards transportation, lead, lift, mathadi charges , Octroi, installation, levies, royalties, insurance, ESI & PF premiums, overheards, fees and rectification of defects or replacement of defective material.
SANITARY FIXTURES & FITTINGS
1 Supply, Installation, testing and commissioning of approved make starwhite Coloured wash basin with single lever basin mixer
and brass nuts, 32 mm CP brass bottle trap of casted type, 40 mm OD PVC waste pipe class 3 ( 6 Kg/cm2 ) concealed in wall
and taken upto the floor trap with necessary specials, 15 mm CP brass angular stop cock with wall flange with necessary
fittings etc., complete. (For Handwash )
Particular
Wash Basin: Jaquar make under counter type Model No: CNS-WHT-701
Flexible tube: Make VIKING
Bottle Trap: Noway p traps- NW-040-AP
Waste Coupling: Jaquar make ALD-CHR-709L130
Angular stop cock : Jaquar make Model CON-CHR-053KN
Basin faucet : Jaquar make Model No SNR-CHR-51011N (Battery operated) Each 0 4 4
Supply, Installation, testing and commissioning of approved make starwhite Coloured wash basin with single lever basin mixer
and brass nuts, 32 mm CP brass bottle trap of casted type, 40 mm OD PVC waste pipe class 3 ( 6 Kg/cm2 ) concealed in wall
and taken upto the floor trap with necessary specials, 15 mm CP brass angular stop cock with wall flange with necessary
fittings etc., complete. (For Handwash )
Particular
Wash Basin: Jaquar make under counter type Model No: CNS-WHT-701
Flexible tube: Make VIKING
Bottle Trap: Noway p traps- NW-040-AP
Waste Coupling: Jaquar make ALD-CHR-709L130
Angular stop cock : Jaquar make Model CON-CHR-053KN
Basin faucet : Jaquar make Model No SNR-CHR-51011 sensor based battery operted (GE-1.3 LPM FLOW RATE ) Each 5
2 Supply, fixing and commissioning of Stainless steel sink without Drain Board(Overall size 510 mm x 432 mm) supported by
C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain
rubber plug, including cutting and making good the wall / floors wherever required. (In Pantry area).
Particular
SS sink : NIRALI Grace plain
Angular stop cock : Jaquar make model: CON-CHR-053
Sink Cock : Jaquar make model : SNR-CHR-6359 table mounted
Bottle Trap: Noway p traps- NW-040-A Each 1 6 7 14
Supply, fixing and commissioning of Stainless steel sink without Drain Board(Overall size 510 mm x 432 mm) supported by
C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain
rubber plug, including cutting and making good the wall / floors wherever required. (In Pantry area).
Particular
SS sink : NIRALI Grace plain
Angular stop cock : Jaquar make Model CON-CHR-053KN
Waste Coupling: Jaquar make ALD-CHR-709
Sink Cock : Jaquar make model: SOL-6359 (GE-1.3 LPM FLOW RATE ) table mounted (Manual Operated)
Bottle Trap: Noway p traps- NW-040-AP Each 14
3 Supply, fixing and commissioning of Stainless steel sink with Drain Board (Overall size 1145 mm x 432 mm) supported by
C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain
rubber plug, including cutting and making good the wall / floors wherever required. (Cafeteria)
Particular
SS sink : NIRALI Elegence
Angular stop cock : Jaquar make model: CON-CHR-053
Sink Cock : Jaquar make model : SNR-CHR-51445PK table mounted (Battery operated)
Bottle Trap: Noway p traps- NW-040-A Each 0 1 1
Supply, fixing and commissioning of Stainless steel sink with Drain Board (Overall size 1145 mm x 432 mm) supported by
C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain
rubber plug, including cutting and making good the wall / floors wherever required. (Cafeteria)
Particular
SS sink : NIRALI Elegence
Angular stop cock : Jaquar make model: CON-CHR-053
Sink Cock : Jaquar make model : CON-CHR-309KNBM( GE-1.3 LPM @ 3.0 Bar pressure) - Sink Mixer with Swinging Spout (Table
Mounted Model)
Bottle Trap: Noway p traps- NW-040-A Each 1
Supply, fixing and commissioning of Stainless steel sink without Drain Board(Overall size 510 mm x 432 mm) supported by
C.I. / M.S. Brackets, C.P. cast brass bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass chain
rubber plug, including cutting and making good the wall / floors wherever required (Mother's Room)
Particular
SS sink : NIRALI Grace plain
Angular stop cock : Jaquar make model: CON-CHR-053
Sink Cock : Jaquar make model : CON-CHR-309KNBM( GE-1.3 LPM @ 3.0 Bar pressure) - Sink Mixer with Swinging Spout (Table
Mounted Model)
Bottle Trap: Noway p traps- NW-040-A Each 1
4 Supply, installation, testing and commissioning of storage type Water Heater of approved shade with copper container,
glasswool insulation, stove enamlled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, angle valve on
inlet connection, 15 mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 5/8 kg/sqcm
complete as required.cost should include all accessories as required for installation
5 Supply, Installation, testing and commissioning of approved make fixing of angle stop cock with wall flange etc., complete.
6 Supplying and fixing in position PVC floor trap of "P" trap for wet areas. Making proper connection with cement solvent
joints, cutting chase / hole / core cut in floors / slabs and bringing the same in proper condition and shape after placing the trap
in right position complete as required.
7 Supply & fixing of 5"X5" SS grating (heavy quality Chilly make cockroach trap) etc., complete.
Make: Chilly (CCT-S-129)
a) 5" X 5" SS grating No's 1 0 3 4 12
2 Providing and fixing nitrle rubber insulation on hot water supply / return pipes.
20/22 mm dia (9 mm thickness) Rmt 0 6 6 12
3 Supply and fixing brass gun metal level operated Ball valve, tested to a pressure of 16 Kg/Sq.cm. including flanges / union,
nuts, bolts, washer etc., complete as required.
a) 20 mm dia No's 1 2 2 5 4
b) 25 mm dia No's 0 0 0 0
c) 32 mm dia No's 0 1 1 1
WASTE (INTERNAL)
1 Supplying, laying, jointing, testing and commissioning approved make PVC pipes SWR Type-B 10 Kg/cm2 with solvent
cement joints confirming to IS: 13592:92 and fittings IS 14735:99 for soil, waste & vent installation, cut to required lengths
including all necessary fittings and specials such as Bends, junctions, offsets, access pieces (plan or door) & vent cowl. Fixing
at wall / ceiling level supported by clamps & hangers etc. Making proper connection with cement solvent / rubber ring joint of
required depth including cutting, chases / holes in floors / walls / slab etc., and making good the same after pipe have been
duly laid and testing complete.
a) 40 mm dia Rmt 0 12 12 16
b) 50 mm dia Rmt 2 6 19 27 37
2 Supplying, laying, jointing, testing and commissioning approved make PVC pipes SWR pipe class III 6 Kg/cm2 with solvent
cement joints confirming to IS: 13592 for soil, waste & vent installation, cut to required lengths including all necessary fittings
and specials such as Bends, junctions, offsets, access pieces (plan or door) & vent cowl. Fixing at wall / ceiling level supported
by clamps & hangers etc. Making proper connection with cement solvent / rubber ring joint of required depth including
cutting, chases / holes in floors / walls / slab etc., and making good the same after pipe have been duly laid and testing
complete.
a) 75 mm dia (Silencio pipe-Astral/ Ashirwad) Rmt 16 0 42 58 46
Supply, installation, testing and commissioning of Kessel make minilift (Art 28560) model pump with all necessary
3 accessories etc., complete. Make: Kessel Minilift (Model no 28560) No's 1 1 1
Supply, installation and commissioning of Lifting station near Sink waste discharge (Tank capacity: 35 ltrs) with (1W+1S)
4 submersible pump with all automatic control valves etc., complete. Make: Kessel AQUA LIFT F CAMPACT DUO (Model no No's 1 1 2 2
28743-C)
Supply, installation of Grease Interceptor KESSEL make Article No.: 93025 (or) Nugreen make SS 304 Grease separator
5 NGT- 14 No's 0 1 1 1
Supply, installation and transportation to respective location : RO (RO+UV+UF)- WAE-VAR 150 ltrs LPH Capacity storage
6 standlone unit having dispensers, Cold water 20 ltrs, Hot water 5 ltrs, Ambient 130 ltrs, with sensor dispenser with proper No's 1 1 2 2
drain board facilities. Make : WAE
Total Amount - -
PROJECT NAME
CLIENT NAME
SERVICE CONSULTANT
REVISION & DATE
TITTLE
BUILDING MANAGEMENT SYSTEM - DATA POINT SUMMARY
DDC CONFIGURATIONS TOTAL
DDC-1 TO AHU 18 18
DDC 18
SR NO POINT DESCRIPTION AI DI AO DO SOFT POINTS
MONITORCONTROL ALARM
1.00 GNED, 7TH & 8TH FLOOR - TOTAL 18 NOS
1.01 Supply Air Velocity Monitoring 1 √ √
1.02 AHU Pre Filter clean status monitoring 1 √ √
1.03 Chilled Water Modulating Valve Control 1 √ √
1.04 Chilled Water Modulating Valve Status Monitoring 1 √
1.05 chilled water inlet & Out let tempearture monitoring 2 √
1.06 Supply Air Temperature Monitoing 1 √ √
1.07 AHU ON /OFF command 1 √
1.08 AHU Trip status 1 √ √
1.09 AHU Run status monitoring 1 √ √
1.10 Return air CO2 sensor input 1 √ √
1.11 Fire Damper open close Status monitoring+ fresh air fire dampe 4 √
1.12 ON/OFF damper command and Monitor 4 4
1.13 Differential pressure monitoing in Main Duct. 2 √ √ √
1.14 AHU Return air temperature and RH Monitoring Monit 2 √ √
1.15 Fire Status monitoring 1 √ √
1.16 Fire alarm Status @ floor level 1 √ √
SOFT POINT
1.00 PAC 200 √ √ √
2.00 VRF 750 √ √ √
3.00 VFD 360 √ √ √
4.00 VAV 2000 √ √ √
APTIV BANGALORE
APTIV BANGALORE
SPACE MATRIX DESIGN CONSULTANT
R1- 23-02-2022
IBMS - INPUT & OUTPUT SUMMARY
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
7th Floor-IDF-03
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
TOTAL 500
7th Floor-MDF-01
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
TOTAL 162
7th Floor-IDF-04
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
1 Workstations 253 1 1 0 253 253 253
1.1 Adhoc Ws 6 1 1 0 6 6 6
2 Soldering Area 1 1 1 0 1 1 1
3 Small conference Room 1 2 1 1 0 2 1
4 Small Conference Room AV 1 1 1 0 1 1 1
5 Large Conference Room 1 5 5 2 1 5 5
6 Large Conference Room AV 1 1 1 0 1 1 1
7 Room schedulers 2 1 0 0 0 2 0
8 Repro 1 1 1 0 1 1 1
9 IDF Room 1 1 1 0 1 1 1
10 RFID 3 1 1 0 3 3 3
11 Soldering Area 1 1 1 0 1 1 1
12 BMS 4 1 0 0 4 4 0
13 WAP Approx 10 1 1 0 10 10 10
14 ACS/CCTV Approx 14 1 0 0 14 14 0
TOTAL 3 297 305 284 6.35417 5.91667
TOTAL 589
8th Floor-IDF-01
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
1 Workstations 245 1 1 0 245 245 245
1.1 Adhoc Ws 107 1 1 0 107 107 107
2 Cabin 1 2 2 0 2 2 2
3 2 Pax Room 4 1 1 1 4 4 4
4 Huddle Room 2 1 1 0 2 2 2
5 Huddle Room AV 2 1 1 0 2 2 2
6 Small conference Room 2 1 1 0 2 2 2
7 Small Conference Room AV 2 1 1 0 2 2 2
8 Large Conference Room 3 5 5 6 3 15 15
9 Large Conference Room AV 3 6 6 6 0 18 18
10 Room schedulers 7 1 0 0 0 7 0
11 Repro 2 1 1 0 2 2 2
12 Reception 1 2 1 1 0 2 1
13 Display KIOSK 1 1 1 0 1 1 1
14 IDF Room 1 1 1 1 0 1 1
15 Electrical Room 1 1 1 0 1 1 1
16 RFID 2 1 0 0 2 2 0
17 WAP Approx 10 1 1 0 10 10 10
18 LMS 1 1 0 0 1 1 0
19 BMS 3 1 0 0 3 3 0
20 ACS/CCTV Approx 14 1 0 0 14 14 0
TOTAL 15 403 443 415 9.22917 8.64583
TOTAL 858
8th Floor-IDF-02
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
1 Workstations 268 1 1 214 0 268 268
1.1 Adhoc Ws 6 1 1 6 0 6 6
2 2 Pax Room 4 1 1 4 0 4 4
3 Cabin 1 2 2 1 0 2 2
4 Huddle Room 2 1 1 4 0 2 2
5 Huddle Room AV 2 1 1 0 2 2 2
6 Small conference Room 1 1 1 1 0 1 1
7 Small Conference Room AV 1 1 1 0 1 1 1
8 Small conference Room 1 1 1 3 0 1 1
9 Small Conference Room AV 1 1 1 0 1 1 1
10 Large Conference Room 3 5 5 3 3 15 15
11 Large Conference Room AV 3 6 6 12 0 18 18
12 18 Pax Board Room 1 5 5 3 0 5 5
13 18 Pax Board Room AV 1 8 8 4 0 8 8
14 Room Schedulers 8 1 0 0 0 8 0
15 Repro 2 1 1 2 0 2 2
16 Social hub 1 2 2 1 1 2 2
17 IDF Room 1 1 1 1 0 1 1
18 Electrical Room 1 1 1 1 0 1 1
19 RFID 2 1 0 0 2 2 0
20 Security 1 1 1 0 1 1 1
21 WAP Approx 10 1 1 0 10 10 10
22 ACS/CCTV Approx 14 1 0 0 10 14 0
TOTAL 260 31 375 351 7.8125 7.3125
TOTAL 726
8th Floor-IDF-03
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
1 Workstations 180 1 1 103 0 180 180
1.1 Adhoc Ws 40 1 1 40 0 40 40
2 2 Pax 4 1 1 2 0 4 4
3 Huddle Room 2 1 1 0 2 2 2
4 Huddle Room AV 2 1 1 0 2 2 2
5 Small conference Room 1 1 1 1 0 1 1
6 Small Conference Room AV 1 1 1 0 1 1 1
7 Small conference Room 1 1 1 0 1 1 1
8 Small Conference Room AV 1 1 1 0 1 1 1
9 Large Conference Room 2 5 5 4 2 10 10
10 Large Conference Room AV 2 6 6 6 0 12 12
11 Room schedulers 6 1 0 0 0 6 0
12 Security control room 1 2 2 2 0 2 2
13 IDF Room 1 1 1 1 0 1 1
14 Cafeteria 1 4 4 3 0 4 4
15 Electrical Room 1 1 1 1 0 1 1
16 RFID 3 1 0 0 3 3 0
17 WAP Approx 10 1 1 0 10 10 10
18 LMS 1 1 0 0 1 1 0
19 BMS 2 1 0 0 2 2 0
20 ACS/CCTV Approx 14 1 0 0 10 14 0
TOTAL 163 35 298 272 6.20833 5.66667
TOTAL 570
8th Floor-IDF-04
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
1 Workstations 277 1 1 227 0 277 277
1.1 Adhoc Ws 19 1 1 19 0 19 19
2 2 Pax Room 2 1 1 4 0 2 2
3 Cabin 2 1 1 1 0 2 2
4 Huddle Room 1 1 1 4 0 1 1
5 Huddle Room AV 1 1 1 0 1 1 1
6 BMS Room 1 2 1 1 0 2 1
7 Soldering Area 1 2 1 2 2 2 1
8 Large Conference Room 1 5 5 2 2 5 5
9 Large Conference Room AV 1 6 6 2 0 6 6
10 Room schedulers 2 1 0 0 0 2 0
11 Repro 1 1 1 2 0 1 1
12 Reception 1 2 1 1 0 2 1
13 IDF Room 1 1 1 1 0 1 1
14 Electrical Room 1 1 1 1 0 1 1
15 RFID 2 1 0 0 2 2 0
16 Security 1 1 1 0 1 1 1
17 Soldering Area 1 1 1 0 1 1 1
18 WAP Approx 10 1 1 0 10 10 10
19 BMS 3 1 1 0 3 3 3
20 ACS/CCTV Approx 14 1 0 0 10 14 0
TOTAL 267 32 355 334 7.39583 6.95833
TOTAL 689
GF
NETWORK POINTS FACE PLATE TOTAL NETWORK POINTS
SL DESCRIPTION NO. OF LOC. DATA-01 DATA-02 QUAD DUAL TOTAL DATA-01 TOTAL DATA-02
2 GRN Room 1 1 1 0 1 1 1
3 Electronic Lab 9 1 1 0 9 9 9
4 Garage Hill Farm 3 4 0 3 0 12 0
5 Lab Garage 2 4 0 2 0 8 0
6 Reception 1 2 2 1 0 2 2
7 Small conference Room 2 1 1 0 2 2 2
8 Small Conference Room AV 2 1 1 0 2 2 2
9 Room schedulers 2 1 0 0 0 2 0
10 Repro 1 1 1 0 1 1 1
11 RFID 2 1 1 0 2 2 2
12 BMS 3 1 0 0 3 3 0
13 LMS 1 2 0 0 1 2 0
14 WAP Approx 3 1 1 0 3 3 3
15 ACS/CCTV Approx 5 1 0 0 5 5 0
TOTAL 6 29 54 22
TOTAL 76
SL. NO. DESCRIPTION TOTAL
HORIZONTAL CABLING
OmSai
SL. NO. DESCRIPTION MAKE PART NUMBER UOM TOTAL RATE Amount REMARKS
DATA-01 POINTS
INSTALLATION
SL. NO. DESCRIPTION Make PART NUMBER UOM TOTAL RATE Amount REMARKS
Net-Verse D-Type Cabinet, 800mm x 42RU x 1000mm. Single hinge perforated front door.
1 Split perforated rear doors. Horizontally split side panels. Two full length PDU brackets. Panduit DAE8212BF Each 17
Cable Management. Casters. Dimensions: 80.5"H x 31.5"W x 39.4"D (2045mm x 800m
Net-Verse D-Type Cabinet, 800mm x 42RU x 1200mm. Single hinge perforated front door.
1 Split perforated rear doors. Horizontally split side panels. Two full length PDU brackets. Panduit DAE8222BF Each 3
Cable Management. Casters. Dimensions: 80.5"H x 31.5"W x 39.4"D (2045mm x 800m
The Wyr-Grid® Pathway protects cables between the main distribution area and the
2 equipment distribution area. The optional side walls snap-on without extra hardware or Panduit WG18BL10 Each 38
tools. It measures 2.09 inches H x 10 feet L x 18 inches W (53.1mm x 3m x 457.2mm).
3 32A, 1PH, Switched PDU, (20)IEC C13+(4)IEC C19 sockets, NMC Display, Hydraulic- Enlogic EN2325 Each 38
Magnetic CB, with IEC60309 Imput Plug, 3 metre power cord
4 CE-13 to CE-14 Power cords 1.8 mtrs Black Longwell Each 255
5 NetManager™ HC Horizontal Single Sided Manager, 2RU, Black Panduit NMF2 Each 19
TOTAL FOR RACKS
BACKBONE CABLING
OmSai
LOI
SL. NO. DESCRIPTION Make PART NUMBER UOM TOTAL RATE Amount REMARKS
FIBER- 2 RUNS OF 24 CORE MM FIBER CABLE FROM SERVER ROOM TO EACH HUB ROOMS
1 50um OM4 24 Fiber Indoor-Outdoor Tight Buffered Cable, LSZH, 900um FLKLZ24 Mtrs 2785
Buffered Fibers Panduit
The Panduit® Opticom® Tray is designed to organize fiber distribution
when space is limited. When partnered with the Panduit CFAPPBL1 Patch FMT1+CFAPPBL1+4*
Panel, it accommodates up to 4 QuickNet cassettes, FAP and FMP adapter FAP6WAQDLCZ+48*
2 NKFPZ1BN1NNM001 Each 16
panels- 48 PORT OM4 LOADED
+4*FSC24
Panduit
The Panduit® Opticom® Tray is designed to organize fiber distribution
when space is limited. When partnered with the Panduit CFAPPBL1 Patch FMT1+CFAPPBL1+2*
Panel, it accommodates up to 4 QuickNet cassettes, FAP and FMP adapter FAP6WAQDLCZ+24*
3 NKFPZ1BN1NNM001 Each 4
panels- 24 PORT OM4 LOADED
+2*FSC24+2*FAPB
Panduit
4 2 fiber OM4 patch cord, riser (OFNR) rated, LC duplex to LC duplex, Each 166
16mm jacket, Std IL 3 meters Panduit NKFPZ22LLLSM003
TOTAL
INSTALLATION
INTERACK
Each 288
2 Category 6A, RJ45, 10 Gb/s, 8-position, 8-wire universal module, Green Panduit CJ6X88TGGR
Each 288
3 Category 6A, RJ45, 10 Gb/s, 8-position, 8-wire universal module, Green Panduit CJ6X88TGGR
4 Mini Each 5
Mini Com
Com 48-port modular high
24-port modular density
patch panel patch panel in black,
with faceplates (1RU).
in black, with Panduit CPP48HDWBLY
5 label and label covers, (1RU). Panduit CPPL24WBLY Each 10
Category 6A Performance, 28AWG, UTP Patch Cord, CM/LSZH, GREEN, UTP28X2MGR Each 120
6 2m. Panduit
Category 6A Performance, 28AWG, UTP Patch Cord, CM/LSZH, GREEN, UTP28X3MGR Each 120
7 3m. Panduit
8 Wire mesh with all accessories in mtrs Legrand local Mtrs 30
TOTAL
INSTALLATION