Professional Documents
Culture Documents
SPEC 2015/01247010
TECHNICAL DRAWING
75 minutes
1. This test consists of 60 items. You will have 75 minutes to answer them.
4. On your answer sheet, find the number which corresponds to your item and shade the space
having the same letter as the answer you have chosen. Look at the sample item below.
Sample Item
The best answer to this item is “hidden details,” so (B) has been shaded.
5. If you want to change your answer, erase it completely before you fill in your new choice.
6. When you are told to begin, turn the page and work as quickly and as carefully as you can. If
you cannot answer an item, go on to the next one. You may return to that item later.
7. You may do any rough work in this booklet.
8. Figures are not necessarily drawn to scale.
(A) segments
(B) round, smooth lines
(C) ellipses or part of ellipses
(D) round arcs without distortions
(A) Compass
(B) Protractor
(C) Flexicurve 4. In the drawing above, which of the
(D) Radius curve following letters indicates the centre of the
arc which is tangential to the two circles?
01247010/SPEC 2015
-3-
6. Which of the following correctly defines Item 8 refers to the following diagram.
the locus of a point?
(B) 36 Dia
Item 9 refers to the following diagram.
36
(C)
R 18
10. Which of the following is a view of a right Item 12 refers to the following diagram.
triangular pyramid?
14. Which of the following drawings shows a Item 16 refers to the following construction.
rectangle equal in area to a triangle?
(A) 30°
(B) 45°
(C) 60°
(D) 90°
18. A cube with an edge of 80 mm is to be 19. Which of the following is a true elevation
drawn in oblique projection. The length of of the drawing shown above?
the receding lines, in mm, should be
(A) 10
(B) 20
(C) 30
(D) 40
20. Which of the following illustrates the 22. Which of the following patterns can be
normal of an ellipse? folded to form a square prism with an
oblique top?
Item 23 refers to the following diagram. Item 26 refers to the following diagram.
R
R
R
29. When sketching pictorial figures, one Item 32 refers to the following diagram.
should first
(A) 10
(B) 15
(C) 20
(D) 30
Item 34 refers to the following diagram. Item 36 refers to the following diagram.
(A) Scale
(B) Sketch
(C) Detail
(D) Engineering
35. In the diagram above, the circles and (A) three medians
curves are shown in their true shapes. The (B) bisectors of any two sides
method of projection used is (C) bisectors of any two angles
(D) perpendicular to any side and a
(A) oblique median
(B) trimetric
(C) isometric
(D) orthographic 39. In a perspective drawing, all vertical lines
Item 40 refers to the following diagram. 43. Which of the following drawings
represents a truncated prism?
(A) 1:2
44. On which of the following planes would
(B) 1:1
the plan of an orthographic projection
(C) 5:1
appear?
(D) 10:1
(A) Profile
(B) Vertical
Item 42 refers to the following figure.
(C) Auxiliary
(D) Horizontal
Item 46 refers to the following diagram. 50. RS is a straight line. A line segment 25 mm
long is marked. Exterior angles of 45° are
marked off at each end of the line segment.
The two angled lines formed are 25 mm
long. If this construction is continued until
a closed figure is formed, the figure
obtained is
(A) a pentagon
(B) a hexagon
(C) an octagon
(D) a nonagon
(A) 75 and 80
(B) 80 and 75
(C) 80 and 105 51. The drawing above shows the development
(D) 100 and 80 of a
53. When a plane figure has a linear reduction Item 56 refers to the following drawing.
only, the
END OF TEST
01247010/SPEC 2015
Item Key Syllabus Reference
1 C 2B.1:1.2 (i)
2 C 1.2:2.2
3 A 2A.1:1.1 (iii)
4 C 2A.1:1.2
5 C 2B.1:1.3
6 B 2A.1:1.4
7 A 1.2:2.5
8 A 2A.1:1.1 (v)
9 C 2A.1:1.1 (iii)
10 C 2B.1:1.5
11 B 2A.1:1.1 (ii)
12 B 2B.1:1.3
13 A 2B.1:1.8
14 C 2A.1:1.5
15 B 2B.1:1.1
16 A 2A.1:1.2
17 D 2A.1:1.2
18 D 2B.1:1.2 (ii)
19 A 2B.1:1.3
20 D 2A.1:1.3
21 B 2A.1:1.3
22 D 2B.1:1.8
23 C 2A.1:1.2
24 A 2A.1:1.2
25 C 2A.1:1.1 (vi)
26 A 2B.1:1.2 (ii)
27 B 2A.1:1.6
28 D 1.2:2.1
29 D 2B.1:1.1
30 C 2B.1:1.8
31 B 2A.1:1.6
32 B 2A.1:1.2
33 B 2B.1:1.3
34 C 2A.1:1.1 (iv)
35 A 2B.1:1.2 (ii)
36 A 2A.1:1.3
37 B 1.3:3.1
38 B 2A.1:1.1 (vi)
39 D 2B.1:1.2 (iii)
40 B 2A.1:1.2
41 A 1.2:2.6
42 B 2B.1:1.2 (i)
43 A 2B.1:1.5
44 D 2B.1:1.3
45 C 1.1:1.4
46 A 2A.1:1.2
47 C 2A.1:1.3
48 C 1.2:2.5
49 B 2A.1:1.1 (vi)
Item Key Syllabus Reference
50 C 2A.1:1.1 (v)
51 D 2B.1:1.8
52 D 2B.1:1.3
53 B 2A.1:1.7
54 A 2A.1:1.1 (vi)
55 B 1.1:1.6
56 C 2A.1:1.1 (vi)
57 A 1.2:2.6
58 C 2A.1:1.1 (iii)
59 C 2A.1:1.1 (iii)
60 C 2B.1:1.3