ns Ganz
Hot-rolled steel plates, sheets and
strip for automobile structural uses
1. Sexe
cifes the hot-rolled steel plates,
shoots and steips (Hereafter referred to as the "steal shoots and coils") with
press drawabiity to be used mainly for automobile frames, wheel
Remark: The units and nunericel values given in ( ) in this Standard
ze based on the International System of Unite (SI) and are
tppended for informative reference.
Further, the traditionsl units accompanied by numerical
valuey in this Standard shall be converted to the SI units and
umerical Values on Jenuary 1, 1981.
2, Grades and symbole
Steet sheets and coils shall be classified into 4 catogories, and thelr
symbole shall be ae given in ‘Table I-l o Table 1~
Table 1-1. Symbols of Grades
(Applicable tll the end of 1990)
‘Grade ‘Applicable thioknes
SAPH 9
SAPH 98 1.6 mm or over up to
Tarn snd iol. 18 om
SAPH &8—¢ aa
‘Table 1-2. Symbols of Grades
(Applicable on and after January 1, 1981)
‘Grade
Gor informative | APplouble thiekne
st units | “reference) 7
Sitional unite
SAPH HO | SAPH 32,
Sari sro | SAPH 38 1.6 mm or over up to
saPH 0 | SAPH «I and nel. 14 wo
SAPH 440 | SAPH &S
3. Chemloa! Composition
Stool sheets and coils shall be tested in secordance with 7.1 and their
wt analyele valies shall conform to Tablo 2-1 or Table 2-2.
‘Table 2-1. Chemical Composition
(Applicable till the end of 1980) aye,
Grade P 5
SAPH 32
SAPH 38
0.040 mex. 0,000 max.
SAPH «I
SAPH «5
‘Table 2-2. Chemical Composition
(Applicable on and after January 1, 1991)
unit:
Grade P 3
SAPH 810
‘APH 370
0,040 mex. 0,040 max,
SAPH 400
‘SAPH 440
6 ms
4. Mochanfeal Properties
Steel sheets and coils shall be tested in accordance with 7.2 and thel=
tensile strength, yield point, elongation and bendability shall’ be as specified
in Table 3-1 or Table 2.
Im the case of bond test, # shall be bent without ersck on the outside
of the bent portion.
‘Table 1. Mechanical Propertios
(Applicable til the end of 1990)
a) ee ae Ge S|
Be) R09)
i a eee
race} E ye. [t ate ls
Hy 24, 2 fiteq 23] 3 :
an Peli| |ByBy*
cris zal] Ee #3
a 1 i
= in sot |main| s0inta, i
"ls
— ee [ele a
sapmag Mim] ies | BR) B85 06o,| somin,|s2utn.|SSatn,|Seain.| Zain, a) se |S
4a | on | sa | gs) ple
Remarks 1. ‘The values specified in Table 3-1 shall not be applied to the
irregular portions of both ends of the stool coll.
2. ‘The figures in ( ) axe given for informative reference.~6 s3—~
—@ a
Table 3-2, Mechanioal Properth Table 4, Tolerances on Thicknes
(Applosble on and after January 1, 1981) Units
TF oo Mo] oo na re eet
vase pint | | Sion er ar ar
ee ee om [aa [oom 7
i, i vex [wom | som [oom
a tom som aoe [ae
fe we [sow [soar [aoa
a | wea [aie [ea [ea
so | aa | atae |wote4 26800 = soa | sow | su | 400
ape 7 if [aes | see [aoa [ane
am | ata. | ata, steal! Es fo. | 20% | 200 | 20m
wy ele ssn] ain ee Renarks 1. The position of measurement on
0 _| ate | atm a RE aera
sari | 40] ‘pul wenlaan|wanluanlaan 3s tis @ uss.
a —— 2, ‘The values specified in Table 4
shi not be applied to the lreogular
Remarks 1, The values specified in Table 3-2 shall not be epplied to the portions of both ends of the steel”
{eregular portions of both ends of the steal coll
2, ‘Tho figures in ( ) are given for informative reference.
5. Shapes, Dimensions, Mass ané Tolerances
‘The shapes, dimensions, mass and their tolerences for stee! sheets and
colts shall conform to J18 0°
‘With this respect, tolerances on length for steel sheets and those on
wiath for eut edged tec! shosts shall, unless otherwise specified, be in ac~
cordance with ‘the tolerance A, and the tolerances on thickness for steel
Shoots and coils shall be ss specified in Table 4.
568
ails
3. The tolerances on thickness for
steel sheets whieh are not manu
factured from steel colla mty be
‘agreed between the purchaser and
the supplier.
5. Appearance
‘The appearance of steel sheets and colls shall conform to 6. of JIS 0 3183,
1. Beste
7.1 Chemical Analyste
Sneiyels, and the general requirements for chemcal analy
fmothod of specimens for anaiyaie shall be aa specified in 3. of JIS G 0303-
1.1.2 Test Mothod The method for chemical ensiyste shall comply with
‘one of ihe Tollowing Standards:
wis @ ie ais 1215,
GIs G 1257 is G 1258
318 1283418 @ 1256
5691.2.1 Tests in Generel The general requirements for the mechanics
test shall be us Specified im 4. of JIS G 0503. However, the sampling
Inethod of specimens shall coniorm to Class A, and the number of test pieces
fand the senpling position shall be es follows:
(1) Number of Test Pisces for Tensile Test and Bend Test
(a) In the Case of Steel Coll and Sheets Cut Length Take each one
‘Wat pisce Tor the tenaile Test andthe end test from each lot of the
Same heet rolled to the sane thickness. When the mass of one lot
Guecads 501, however, take two sete of test pieces from the lot.
(b) Im the Caso of Stet Shoots (Excluding Shoots n_Cut Length
Heats) Bean one taal plese for the tonal tort and the”
bond test shall be taken from each lot of the same heat where
the maximum thickness of the stool sheet 1s not more than twice
the minimum thickness thereof. When the mass of one lot
exceeds 80 t, howaver, take two sets of test plecer from the
ket.
@
The Tolling direction ana the Bend test pioce shall be taken
tranaversely thereto, and the center of a teat plece shall be at
Squasterwidth from the alde edge. When te infesalble to
flow the center of test piece to be at # quarter-wiath from
the side edge, however, the sampling should be made as clove to
the specified position as possible.
1.2.2 ‘Test Piece The tensile tost pioce and the bond test piece shall
conform to the Tollowing requirements
(1) No, 5 oF No. 1A test plece specified in JIS 2 2201
(2) No. 3 test plece specified in a8 Z 2204
1.2.3 Test Methods The methods of tensile test and bend ‘est shall
conform to the Tollowing Standards
@ as ae
(a) is 22008
8. Inspection
8.1 Inspection The inspection shall be carvied out as follows:
(2) The general requirements for the inpection shall be as specified in
ms ¢ 0303.
(2) The chemical composition shall conform to the requirements of 8.
(8) The mechanical properties shall conform to the requlrenents of 4.
—310—
6 su—
(A) Tho shapes, dimensions and mass shall conform to the requirements
Toe to the require
(3) The appearance shall conform to the requirements of 6.
8.2 Reinspection Steel shoots and coils having failed to meet the re-
guivenents of the tense test and bend test my be subjected to s actest for
‘nal eeceptance according to the specification of 4-4 in JIG 0908.
9. Marking
a Miao te et arent i et
G2) ante o petn mse
6) onan
(0 ste eo ting
10. Report
2 repr sao hh elt
- in JIS 6 0303.
-sIL